Audiovox Automobile Electronics AS GMDLT03 User Manual

INSTALLATION GUIDE FOR THE:  
GM Data Bus  
Door Trigger Interface  
AS-GMDLT03  
With Door Locking  
The AS-GMDLT03 Interface module connects to the Class II Data Bus wire, (OBD2), of the vehicle and detects the  
vehicle’s door condition (open or close), provide door lock/unlock information as well as arm/disarm for those  
vehicles with factory alarm systems. This device is used on Chevrolet/GMC & Cadillac, Seirra, Yukon, Denali,  
Light and Medium Duty Pickups, Suburbn, Tahoe, CK Series, Escalade,Avalanche and Hummer H2.  
These vehicles use the on board data bus instead of a common door trigger wire. T ypical installation would  
include the removal of door panels to connect the latch wires of each door.  
The AS-GMDLT03 allows you to pick up the door open close status of the vehicle as well as provide door lock  
unlock signals when required. Simply connect to the alarms negative door trigger input wire, negative door lock  
unlock wires, connect + 12 volts, ground, and one wire to the vehicle’s data bus and your done. No additional  
labor is required to remove panels or run trigger wires throughout the vehicle for door locks and door triggers.  
This module when receiving RF commands fromAudiovox alarm will provide door lock/arm , door unlock drivers &  
disarm & or door unlock all disarm.  
Wiring The Module:  
NOTE: All wires must be verified prior to connection. If you are uncertain of a wire’s function found in  
the DLC, (Data Link Connector), consult the shop manual or callAudiovox Technical Service (1-800-225-6074).  
One Side Of Interface  
Red/White: + 12 Volts  
Connect this wire to the + 12 volt constant wire found in the DLC. Typical vehicle color is Orange.  
Black: Chassis Ground  
Connect this wire to a clean unpainted metal surface in the vehicle or a pre-existing chassis ground wire. Typical  
vehicle color found in the DLC is Black, or Black/White.  
Purple: Data Bus Input  
Connect this wire to the data wire in the DLC connector. Typical vehicle color is Purple.  
Other Side Of Interface  
Brown: Negative Trigger Output  
Connect this wire to the Brown negative door trigger input wire of your Audiovox alarm system.  
Red: Lock  
Connect this wire to the negative door lock wire from the Audiovox Alarm System.  
Green: Unlock 1 Drivers Door  
Connect this wire to the Green unlock 1 wire of the Audiovox Alarm System  
Red/Black: Unlock 2 All Doors Unlock  
Connect this wire to the Red/Black unlock 2 wire of the Audiovox Alarm System.  
White Loop Wire: Keyless/Non Keyless Select  
If the vehicle you are installing this interface into does have Factory Keyless Entry, then the white loop wire  
remains intact, (Closed)  
If the vehicle you are installing this interface into does not have Factory Keyless Entry then this loop must be cut,  
(Open)  
NOTE: If the vehicle does not offer separate drivers door/all door unlock feature or if the customer does not  
want sperate control of driver/all doors, connect the Red/Black of the interface to the green door unlock 1 wire of  
the Audiovox Alarm. If the Audiovox Alarm you are using does not have 3 pin door lock/unlock connector then  
the feature is not available and you must wire the Red/Black of the interface to the Green - door unlock wire of the  
Audiovox Alarm System.  
Once all wires have been connected, turn ignition on then off before testing to ensure proper initialization of the  
interface module.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

ADC Clothes Dryer ML 122 User Manual
Adcom Surge Protector ACE 615 User Manual
ADS Technologies Switch USBH 2004 User Manual
ADTRAN Heart Rate Monitor 1204002L2 User Manual
Amana Microwave Oven UMTK27 User Manual
American Standard Bathroom Aids 2664 User Manual
American Standard Indoor Furnishings 0211008 User Manual
Avery Printer Accessories M09800 User Manual
Baby Trend Stroller 9100 User Manual
Barco Projector DATA 708 User Manual