American Standard Plumbing Product M968582 User Manual

Installation  
Instructions  
4335.020.XXX  
PEKOE EXTENDER  
SINGLE CONTROL KITCHEN  
POP-OUT SPRAY  
Thank you for selecting American-Standard...the benchmark  
of fine quality for over 100 years.  
To ensure that your installation proceeds smoothly--please  
read these instructions carefully before you begin.  
Certified to comply with ANSI A112.18.1M  
M968582 REV.1.1  
Recommended Tools  
Phillips Screwdriver  
Channel Locks  
Adjustable Wrench  
Tubing Cutter  
Plumbers' Putty or Caulking  
INSTALL FITTING  
1
Turn off hot and cold water  
supplies before beginning.  
CAUTION  
Make certain the SEAL (1) is properly seated in recess  
of faucet body.  
Insert supply HOSES (2) and SHANK (3) through center  
hole of sink or mounting surface.  
Assemble RUBBER WASHER (4), PLASTIC WASHER (5),  
METAL WASHER (6) and threaded LOCKNUT (7) onto  
SHANK (3) from underside of sink or mounting surface.  
Hand tighten LOCKNUT (7) and check that faucet is centered.  
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (7).  
Work your way around LOCKNUT (7), tightening the screws  
slightly each time until all are snug to ensure even pressure.  
RECESS  
3
1
2
4
5
6
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE  
4
Clogged CARTRIDGE outlets or inlets may cause reduced  
flow. To clean, first turn off water supply then:  
Loosen and remove LEVER HANDLE (1). Loosen  
HANDLE SCREW (2) with 2.5mm Hex Wrench and  
then pull HANDLE BASE (3) off.  
Unscrew ESCUTCHEON CAP (4). Unscrew the  
CARTRIDGE NUT (5) and remove METAL WASHER (8).  
Remove CARTRIDGE (6). Clean inlets of  
CARTRIDGE (6) and MANIFOLD (7).  
METAL  
WASHER  
8
CLEAN  
Reassemble CARTRIDGE (6). Replace CARTRIDGE  
NUT (5), CAP (4), METAL WASHER (8) and  
HANDLE assembly, check flow.  
1
5
4
7
2
6
3
SERVICE  
5
If SPOUT (1) leaks at swivel point the O-RINGS (2) need  
to be replaced. To remove SPOUT (1):  
Turn faucet to off position. Loosen the SPOUT SET SCREW (3)  
with a 3mm Hex wrench.  
Rotate the SPOUT (1) side to side while pulling upward to  
remove SPOUT (1) from faucet body.  
Replace the defective parts and grease O-RINGS (2). Push  
SPOUT (1) back into position. Tighten SET SCREW (3).  
1
REMOVE  
INSTALL  
Check that SPOUT (1) rotates freely and does not leak  
at the swivel point.  
2
3
3mm HEX  
WRENCH  
CARE INSTRUCTIONS:  
6
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.  
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A  
CLOTH WITH A COARSE SURFACE.  
M968582 REV.1.1  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Abit Computer Hardware AW8 User Manual
ADC Network Card InterReach User Manual
Agilent Technologies All in One Printer 03561 90010 User Manual
Allied Telesis Network Card AT 2916LX10 LC 901 User Manual
Alpine Flat Panel Television TME M580 User Manual
American Power Conversion Switch MasterSwitch User Manual
American Standard Outdoor Shower 1043 Series User Manual
BC Speakers Speaker 6NDL44 User Manual
Behringer Stereo System SX3040 User Manual
Beko Oven GM 15120 DA PR User Manual