Allied Telesis Switch 8648T 2SP User Manual

AT-8600 Series Switch  
Installation and Safety Guide  
AT-8624T/2M  
AT-8624PoE  
AT-8648T/2SP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2
AT-8600 Series Switch  
AT-8600 Installation & Safety Guide  
Document Number C613-000083 REV D.  
© 2006 Allied Telesis Inc. All rights reserved. No part of this publication may be  
reproduced without prior written permission from Allied Telesis Inc.  
Allied Telesis Inc. reserves the right to change specifications and other  
information in this document without prior written notice. The information  
provided herein is subject to change without notice. In no event shall Allied  
Telesis Inc. be liable for any incidental, special, indirect, or consequential  
damages whatsoever, including but not limited to lost profits, arising out of or  
related to this manual or the information contained herein, even if Allied Telesis  
Inc. has been advised of, known, or should have known, the possibility of such  
damages.  
All company names, logos, and product designs that are trademarks or  
registered trademarks are the property of their respective owners.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation & Safety Guide  
3
Electrical Safety and Emission Compliance Statement  
STANDARDS: This product meets the following standards:  
Category  
Approval Agency and Requirement  
UL60950-1  
CAN/CSA-C22.2 No. 60950-1-03  
EN60950-1  
EN60825-1  
Electromagnetic Compliance  
FCC CFR47 Part 15 Class A  
EN55022 Class A  
EN61000-3-2  
EN61000-3-3  
VCCI Class A  
AS/NZS CISPR22 Class A  
Immunity  
EN55024  
U.S. Federal Communications Commission  
RADIATED ENERGY  
Note: This equipment has been tested and found to comply with the limits for a Class A digital device  
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection  
against harmful interference when the equipment is operated in a commercial environment. This  
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in  
accordance with this instruction manual, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful interference in which case  
the user will be required to correct the interference at his own expense.  
Canadian Department of Communications  
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing  
Equipment Regulations.  
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel  
brouilleur du Canada.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4
AT-8600 Series Switch  
Electrical Safety  
IMPORTANT: This equipment must be installed in accordance with safety  
precautions (page 20).  
Elektrische Sicherheit  
WICHTIG: Für die Installation dieses Gerätes ist die Einhaltung von  
Sicherheitsvorkehrungen erforderlich (Seite 21).  
Elektrisk sikkerhed  
VIGTIGT: Dette udstyr skal installeres i overensstemmelse med  
sikkerhedsadvarslerne (side 23).  
Elektrische veiligheid  
BELANGRIJK: Dit apparaat moet in overeenstemming met de  
veiligheidsvoorschriften worden geïnstalleerd (pagina 24).  
Sécurité électrique  
IMPORTANT: Cet équipement doit être utilisé conformément aux instructions  
de sécurité (page 25).  
Sähköturvallisuus  
TÄRKEÄÄ: Tämä laite on asennettava turvaohjeiden mukaisesti (sivu 26).  
Sicurezza elettrica  
IMPORTANTE: questa apparecchiatura deve essere installata rispettando le  
norme di sicurezza (pagina 28).  
Elektrisk sikkerhet  
VIKTIG: Dette utstyret skal installeres i samsvar med sikkerhetsregler  
(side 29).  
Segurança eléctrica  
IMPORTANTE: Este equipamento tem que ser instalado segundo as medidas de  
precaução de segurança (página 30).  
Seguridad eléctrica  
IMPORTANTE: La instalación de este equipo deberá llevarse a cabo cumpliendo  
con las precauciones de seguridad (página 31).  
Elsäkerhet  
OBS! Alla nödvändiga försiktighetsåtgärder måste vidtas när denna utrustning  
används (sida 33).  
EC Declaration of Conformity  
EC Declaration of Conformity (page 35).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation & Safety Guide  
5
Table of Contents  
Veiligheid ........................................................................................................................... 24  
Sécurité ............................................................................................................................. 25  
Turvallisuus ....................................................................................................................... 26  
Norme di Sicurezza ........................................................................................................ 28  
Sikkerhet ........................................................................................................................... 29  
Segurança .......................................................................................................................... 30  
Seguridad .......................................................................................................................... 31  
Säkerhet ............................................................................................................................ 33  
EC Declaration of Conformity .................................................................................... 35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
AT-8600 Series Switch  
Models Covered By This Guide  
This Installation & Safety Guide includes information on these models:  
AT-8624T/2M 24-port 10BASE-T/100BASE-TX Layer 3 Fast Ethernet  
Switch  
AT-8624PoE 24-port 10BASE-T/100BASE-TX Layer 3 Fast Ethernet Switch  
AT-8648T/2SP 48-port 10BASE-T/100BASE-TX Layer 3 Fast Ethernet  
Switch  
You can download Installation & Safety Guide updates from  
Package Contents  
These items are included with each AT-8600 Series switch:  
One AC power cord  
One power cord retaining clip  
One serial cable for connecting the switch to a terminal or PC  
One 19 inch rack-mount kit  
One AT-8600 Series Installation & Safety Guide (which includes statutory and  
safety information)  
One AT-8600 Series Documentation and Tools CD-ROM (which includes  
the complete AT-8600 Series document set and utilities)  
One warranty card  
Contact your authorised distributor or reseller if any items are damaged or  
missing.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Installation & Safety Guide  
7
Selecting a Site  
You can install the switch in a standard 19-inch rack, on a level surface such as a  
desktop or bench, or against a wall using the optional wall-mount kit. How to  
install the switch using the 19-inch rack-mount kit is described below. .  
When you install the switch, choose a site that:  
allows adequate airflow around the switch and its vents.  
is free of dust and moisture.  
will maintain an ambient temperature range of 0 º C to 40º C  
(32º F to 104º F) and a humidity range of 5% to 80% non-condensing.  
has a reliable and earthed (grounded) power supply, preferably dedicated  
and filtered.  
does not expose cabling to sources of electrical noise such as radio  
transmitters, broadband amplifiers, power lines, electric motors, and  
fluorescent fixtures.  
allows easy access to the switch’s power and cable connections.  
allows all related network devices to be connected to the switch without  
exceeding maximum cable length limitations as specified in the AT-8600  
Series Hardware Reference.  
ensures that when the switch is mounted in a rack, the switch is mounted  
evenly to prevent uneven mechanical loading of the rack.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
8
AT-8600 Series Switch  
How to Install the Switch  
Warning All versions of this equipment must be earthed.  
Prepare to install the switch  
1. Read the safety information  
Read the safety information included in this Installation & Safety Guide. This  
Installation & Safety Guide is also on the Documentation and Tools CD-ROM  
and you can download a copy from http:// www.alliedtelesis.com.  
2. Gather the tools and equipment you will need  
You will need a Phillips #2 flat-head screwdriver and cage nuts to attach the  
brackets to your rack. These are not supplied.  
3. Choose a suitable operating location  
Follow the guidelines described in “Selecting a Site” on page 7 to choose a  
suitable location.  
You can install the switch either in a 19-inch rack, on a flat bench, or against  
a wall.  
4. Unpack the switch  
Verify the package contents. If any items are damaged or missing, contact  
your authorised distributor or reseller.  
5. Install expansion modules (optional)  
The only expansion module supported by the AT-8624T/2M is the AT-A46.  
If you purchased expansion modules, install them now by following the  
instructions in the AT-A45/xx Series , AT-A46, and AT-A47 Expansion Modules  
Installation Guide that comes with the modules. The AT-A46 expansion  
module is supported by AT-8000 Series switches as well as AT-8600 Series  
switches.  
Hot swap of expansion modules is not supported on AT-8624T/2M  
switches. If you insert or remove a module when the switch is already  
powered on, you must restart the switch before the module can be used.  
6. Place the switch in its operating location  
If installing the switch in a rack:  
Remove the rubber feet on the bottom of the switch with a flat-head  
screwdriver.  
Attach the two rack-mounting brackets to the switch with the screws  
provided in the rack-mount kit.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation & Safety Guide  
9
Mount the switch in the rack using standard screws (these are not  
provided).  
7. Install SFPs  
For the AT-8648T/2SP, you may also need an optional SFP (Small Form-  
factor Pluggable module).  
Do not look into the optical ports of SFP cables or transceivers. Invisible  
laser radiation may be emitted from disconnected fibres or connectors.  
The SFP transceivers must be inserted the right way into the SFP 49 or SPF  
50 slots. See the figure below.  
Slide the transceiver into the SFP socket, and firmly press it until it engages.  
To remove it, first release it by gently pulling the release lever, and then pull  
it out of the socket. Never force a transceiver into or out of a socket.  
When an SFP is installed into one of the two SFP ports, that SFP port takes  
precedence over its corresponding 10/100/1000T port. When the SFP is  
removed, the 10/100/1000T port is once again active.  
8. Check the supply voltage and the switch’s rated voltage  
AT-8600 Series switches are fitted with a universal main power supply that  
will function over the range 100–240 VAC and 50–60 Hz.  
The specific power supply requirements for a particular model are clearly  
displayed on the rear or underside of the switch. If the supply is outside the  
accepted range for the switch, the switch may not operate or damage to  
the switch may result.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
AT-8600 Series Switch  
9. Apply AC power to the switch  
Plug the power cord into the AC power connector. This is on the switch’s  
rear panel, as shown in the below figures.  
Figure 1: AT-8624T/2M front and rear panel with AC power inlet.  
AT-8624T/2M  
Layer  
3
Fast Ethernet Switch  
1
3
5
7
9
11  
13  
15  
17  
19  
21  
23  
MODE  
RS-232  
TERMINAL PORT  
STATUS  
1
2
3
4
5
6
7
8
9
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
COL  
100  
LINK  
MODE  
LINK  
FAULT  
MASTER  
RPS  
25  
26  
FULL  
ACT  
MODE  
PWR  
10  
2
4
6
8
10  
12  
14  
16  
18  
20  
22  
24  
Figure 2: AT-8624PoE front and rear panel with AC power inlet  
AT-8624POE  
Layer  
3
Fast Ethernet Switch  
STATUS  
1
3
5
7
9
11  
13  
15  
17  
19  
21  
23  
100 LINK  
FULL DUP  
PD ON  
ACT  
10 LINK  
HALF DUP  
PD ERR  
ACT  
COL  
MAX CURRENT  
MODE  
RS-232  
TERMINAL PORT  
1
3
5
7
9
11 13 15 17 19 21 23  
FAULT  
MASTER  
RPS  
25  
26  
PWR  
2
4
6
8
10 12 14 16 18 20 22 24  
2
4
6
8
10  
12  
14  
16  
18  
20  
22  
24  
Figure 3: AT-8648T/2SP front and rear panel with AC power inlet  
LINK  
49R MODE  
CLASS  
1
LASER PRODUCT  
AT-8648T/2SP  
Layer  
3
Fast Ethernet Switch  
DO NOT STARE  
49  
INTO BEAM  
LINK  
STATUS  
COL  
FLT  
SFP  
50  
LINK  
SPD  
FDX  
ACT  
MSTR  
RPS  
PWR  
LINK  
50R MODE  
MODE  
10. Check that the PWR LED on the switch’s front panel lights green  
If the PWR (power) LED fails to light, refer to the AT-8600 Series Hardware  
Reference for troubleshooting information.  
11. Connect the data cables  
Make sure each cable connection is secure. The switch will now perform  
basic Layer 2 switching functions.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation & Safety Guide  
11  
How to Configure the Switch  
Some configuration is necessary to enable the switch’s advanced switching  
capabilities. This is achieved via the Command Line Interface (CLI). On the  
AT-8624T/2M, you can also use the Graphical User Interface (GUI).  
Using the CLI to configure a switch  
1. Connect a terminal or PC to the Terminal Port (ASYN0).  
Using the supplied RS-232 DB9 serial straight-through cable, connect your  
terminal or PC to the RS-232 Terminal Port:  
For the AT-8624T/2M and AT-8624PoE, the RS-232 Terminal Port is on  
the front panel.  
For the AT-8648T/2SP, the RS-232 Terminal Port is on the back panel.  
2. Set the communication parameters.  
Set the communication parameters on your terminal or terminal emulation  
program to:  
Bit rate: 9600  
Data bits: 8  
Parity: None  
Stop bits: 1  
Flow control: None  
3. Log in.  
After the switch has booted, the login prompt appears. If the login prompt  
does not appear, press [Enter] two or three times.  
When the switch boots for the first time it automatically creates an  
account with manager privileges. The account has the login name manager  
and the password is friend.  
At the login prompt, enter the login name and password:  
Login: manager  
Password: friend  
The switch’s command prompt appears. Now use the CLI to configure the  
switch.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
12  
AT-8600 Series Switch  
4. Change password and display help.  
Change the password as soon as possible because a manager account left  
with the default password is a serious security risk. Remember the new  
password as there is no way to retrieve it if it is lost.  
To change the account password, use the command:  
set password  
To display a list of help topics, use the command:  
help  
To display help on a specific topic, use the command:  
help topic  
Alternatively, type a question mark (?) at the end of a partially completed  
command to see a list of valid options.  
How to configure the switch is explained in detail in the AT-8600 Series Software  
Reference.  
Using the GUI to configure the AT-8624T/2M switch  
This section describes how to establish a connection to the AT-8624T/2M switch  
through the GUI so you can configure it before installing it in your LAN.  
1. Select a PC to use and identify its subnet.  
You can browse to the switch from any PC that is running a supported  
operating system with a supported browser installed. JavaScript must be  
enabled. If you are using a toolbar or plug-in on your browser to block pop-  
ups, disable it while using the GUI. The GUI displays detailed configuration  
options and information in pop-up windows.  
2. Connect the PC to the switch.  
Use an Ethernet cable to connect an Ethernet card on the PC to any one of  
the switch ports.  
You can browse to the router through any VLAN, as long as you give that  
VLAN an IP address. These instructions assume you are using vlan1. All  
switch ports belong to vlan1 by default.  
3. Access the switch’s command line interface.  
Access the CLI from the PC, as described in the previous section, “Using  
the CLI to configure a switch”.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation & Safety Guide  
13  
4. Enable IP.  
enable ip  
5. Assign the vlan1 interface an IP address in the same subnet as the  
PC.  
add ip interface=vlan1 ip=ipaddress mask=mask  
6. Save the configuration and set the switch to use it on bootup.  
create config=your-name.cfg  
set config=your-name.cfg  
7. On the PCs web browser, bypass the HTTP proxy server, if  
necessary.  
8. Point your web browser at IP address for vlan1.  
9. At the login prompt, enter the user name and password.  
User Name: manager <the default>  
Password: friend  
The System Status page is displayed. Select options from the sidebar menu  
to configure and manage the switch.  
For context-sensitive online help, click the Help button at the top of the  
sidebar menu or on any pop-up page.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
AT-8600 Series Switch  
LEDs on AT-8600 Series Switches  
The following tables outline how the switch and expansion modules report faults  
and operational activities. Expansion modules are optional and can be purchased  
separately. Contact an authorised Allied Telesis distributer or reseller, or visit  
System LEDs  
LED  
State  
Off  
Description  
FAULT  
Switch operation is normal.  
Red  
The switch or management software is  
malfunctioning.  
1 flash  
A switch fan has failed.  
3 flashes  
The main PSU has failed and the RPS is now  
providing power.  
4 flashes  
The RPS Monitor is set to ON, and the RPS  
is not functioning, either because it has failed  
or has been switched off.  
5 flashes  
7 flashes  
The RPS Monitor is set to ON, but the RPS  
is not connected.  
For the AT-8624T/2M and AT-8624PoE  
switches: An expansion module has been  
inserted or removed while the switch is  
powered on.  
MASTER  
RPS  
This LED is not supported and will never be lit.  
Green  
An optional redundant power supply is  
connected to the switch.  
OFF  
There is no optional redundant power  
supply connected to the switch.  
PWR  
Green  
Off  
The switch is receiving power and the  
voltage is within the acceptable range.  
The switch is not receiving power.  
Note Use the Mode Select button to toggle the Mode LEDs to the desired state.  
Toggling the Mode Selection button does not affect the normal operations of the  
switch.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation & Safety Guide  
15  
Link and Mode LEDs for the AT-8624T/2M switch  
LED  
State  
Description  
LINK  
OFF  
There is no link between the port and the  
end-node.  
Green  
A valid link has been established between  
the port and the end-node.  
Mode - COL OFF  
No data collisions are occurring on the  
port.  
Flashing Green  
OFF  
Green  
Mode - FULL OFF  
Data collisions are occurring on the port.  
The port is operating at 10 Mbps.  
The port is operating at 100 Mbps.  
Mode - 100  
The port is operating in half-duplex  
mode.  
Green  
The port is operating in full-duplex  
mode.  
Mode - ACT  
OFF  
Flashing Green  
There is no activity on the port.  
There is activity on the port. It is  
transmitting and/or receiving data.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16  
AT-8600 Series Switch  
Link and Mode LEDs for the AT-8624PoE switch  
LED  
State  
Description  
L/A Status  
(Top LED)  
OFF  
There is no link between the port  
and the end-node.  
Green  
The port is operating at 100 Mbps.  
Flashing Green  
There is activity on the port. It is  
transmitting and/or receiving data  
at 100 Mbps.  
Red  
The port is operating at 10 Mbps.  
Flashing Red  
There is activity on the port. It is  
transmitting and/or receiving data  
at 10 Mbps.  
Mode LEDs  
OFF  
Either DC Mode or PoE Mode.  
(Bottom LED)  
D/C Mode  
OFF  
There is no link between the port  
and the end-node.  
Green  
Red  
The port is operating in full duplex  
mode.  
The port is operating in half-duplex  
mode.  
Flashing Red  
The port is operating in half-duplex  
mode and data collisions are  
occurring on the port.  
PoE Mode  
OFF  
There is no powered device  
detected.  
Green  
The end-node is a powered device  
and the port is providing power to  
it.  
Red  
The port is experiencing a problem  
providing PoE to the end-node.  
Flashing Red  
The port is connected to a  
powered device but providing  
power to it would exceed the  
maximum PoE power budget of the  
switch.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation & Safety Guide  
17  
Link and Mode LEDs for the AT-8648T/2SP switch  
LED  
State  
Description  
LINK  
OFF  
There is no link between the port  
and the end-node.  
Green  
A valid link has been established  
between the port and the end-  
node.  
Mode - COL  
OFF  
No data collisions are occurring on  
the port.  
Flashing Green  
Data collisions are occurring on  
the port.  
Mode - SPD  
Mode - FDX  
OFF  
The port is operating at 10 Mbps.  
The port is operating at 100 Mbps.  
Green  
OFF  
The port is operating in half-duplex  
mode.  
Green  
The port is operating in full-duplex  
mode.  
Mode - ACT  
OFF  
There is no activity on the port  
There is activity on the port.  
Flashing Green  
Download from Www.Somanuals.com. All Manuals Search And Download.  
18  
AT-8600 Series Switch  
SFP and 10/100/1000Base-T LEDs for the AT-8648T/2SP switch  
LED  
State  
Description  
LINK  
OFF  
There is no link between the port  
and the end-node.  
Green  
A valid link has been established  
between the port and the end-  
node.  
Mode - COL  
Mode - SPD  
Mode - FDX  
Mode - ACT  
OFF  
No data collisions are occurring on  
the port.  
Flashing Green  
OFF  
Data collisions are occurring on  
the port.  
The port is operating at 10/100  
Mbps.  
Green  
OFF  
The port is operating at 1000  
Mbps.  
The port is operating in half-duplex  
mode.  
Green  
The port is operating in full-duplex  
mode.  
OFF  
There is no activity on the port  
There is activity on the port.  
Flashing Green  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation & Safety Guide  
19  
Documentation and Tools CD-ROM  
The Documentation and Tools CD-ROM bundled with each switch contains the  
complete documentation set for AT-8600 Series switches and their expansion  
options, as well as tools to manage the switch.  
The documentation and tools CD-ROM includes:  
This Installation & Safety Guide, which also provides safety and statutory  
information for the AT-8600 Series switch and its expansion options.  
The AT-8600 Series Hardware Reference, which provides detailed information  
on the switch unit and its hardware features.  
The AT-8600 Series Software Reference, which provides detailed information  
on configuring the switch unit and its software.  
The AT-A45/xx Series, AT-A46, and AT-A47 Expansion Modules Installation Guide,  
which outlines the procedure for installing expansion modules, and  
provides technical specifications for the modules.  
AT-TFTP Server for Windows for downloading software releases.  
How To notes, white papers, Visio Stencils, and information about related  
Allied Telesis products.  
MIBs supported by the switch  
Adobe Acrobat Reader for viewing online documentation.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
20  
AT-8600 Series Switch  
Safety  
WARNING: In a domestic environment this product may cause radio  
interference in which case the user may be required to take adequate measures.  
WARNING: Class 1 Laser product.  
WARNING: Do not stare into the laser beam.  
CAUTION: Use of controls or adjustments of performance or procedures  
other than those specified herein may result in hazardous radiation exposure.  
ELECTRICAL NOTICES  
WARNING: ELECTRIC SHOCK HAZARD  
To prevent ELECTRIC shock, do not remove the cover. No user-serviceable  
parts inside. This unit contains HAZARDOUS VOLTAGES and should only be  
opened by a trained and qualified technician.  
LIGHTNING DANGER  
DANGER: DO NOT WORK on equipment or CABLES during periods of  
LIGHTNING ACTIVITY.  
CAUTION: POWER CORD IS USED AS A DISCONNECTION DEVICE. TO  
DE-ENERGIZE EQUIPMENT, disconnect the power cord.  
ELECTRICAL - TYPE CLASS 1 EQUIPMENT  
THIS EQUIPMENT MUST BE EARTHED. Power plug must be connected to a  
properly wired earth ground socket outlet. An improperly wired socket outlet  
could place hazardous voltages on accessible metal parts.  
PLUGGABLE EQUIPMENT, the socket outlet shall be installed near the  
equipment and shall be easily accessible.  
CAUTION: Air vents must not be blocked and must have free access to the  
room ambient air for cooling.  
OPERATING TEMPERATURE: This product is designed for a maximum ambient  
temperature of 40 degrees C.  
ELECTRICAL - AC MAINS CIRCUIT OVERLOADING  
When installing product, consideration must be given to the accumulative  
nameplate ratings when connecting the equipment to the AC supply wiring.  
CAUTION: MECHANICAL LOADING - Mounting of the equipment in the rack  
should be such that a hazardous condition is not achieved due to uneven loading.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation & Safety Guide  
Lithium Battery - Should only be changed by authorised service personnel.  
21  
CAUTION: Danger of explosion if battery incorrectly replaced. Replace only  
with Lithium Battery, type CR2032, and dispose of in accordance with the  
manufacturer’s recommendations and all local codes.  
ALL COUNTRIES: Install product in accordance with local and National  
Electrical Codes.  
WARNING: Only trained and qualified personnel are allowed to install or  
replace this equipment.  
CAUTION: This unit does not contain serviceable components. Please return  
damaged units for servicing.  
CAUTION: The AT-8624PoE Ethernet ports are only intended for installation in  
Environment A as defined in IEEE 802.3af. All interconnected equipment must be  
contained in the same building including the interconnected equipment’s  
associated LAN connections.  
CAUTION: The surface-mount fuses F1 to F24 on the Power over Ethernet  
daughterboard in the AT-8624PoE switch are 60V, max 2A fuses. These fuses are  
not field-replaceable, and should only be serviced by a trained Allied Telesis  
service technician.  
Sicherheit  
WARNUNG: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen  
hervorrufen. In diesem Fall müßte der Anwender angemessene  
Gegenmaßnahmen ergreifen.  
WARNUNG Laserprodukt der Klasse 1.  
WARNUNG Nicht direkt in den Strahl blicken.  
ACHTUNG: GEFÄHRLICHE SPANNUNG  
Das Gehäuse nicht öffnen. Das Gerät enthält keine vom Benutzer wartbaren  
Teile. Das Gerät steht unter Hochspannung und darf nur von qualifiziertem  
technischem Personal geöffnet werden.  
GEFAHR DURCH BLITZSCHLAG  
GEFAHR: Keine Arbeiten am Gerät oder an den Kabeln während eines  
Gewitters ausführen.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
22  
AT-8600 Series Switch  
VORSICHT: DAS NETZKABEL DIENT ZUM TRENNEN DER  
STROMVERSORGUNG. ZUR TRENNUNG VOM NETZ, KABEL AUS DER  
STECKDOSE ZIEHEN.  
GERÄTE DER KLASSE 1  
DIESE GERÄTE MÜSSEN GEERDET SEIN. Der Netzstecker darf nur mit einer  
vorschriftsmäßig geerdeten Steckdose verbunden werden. Ein  
unvorschriftsmäßiger Anschluß kann die Metallteile des Gehauses unter  
gefährliche elektrische Spannungen setzen.  
STECKBARES GERÄT: Die Anschlußbuchse sollte in der Nähe der Einrichtung  
angebracht werden und leicht zugänglich sein.”  
VORSICHT  
Die Entlüftungsöffnungen dürfen nicht versperrt sein und müssen zum Kühlen  
freien Zugang zur Raumluft haben.  
BETRIEBSTEMPERATUR: Dieses Produkt wurde für den Betrieb in einer  
Umgebungstemperatur von nicht mehr als 40° C entworfen.  
NETZSICHERUNG  
Bei der Installation muß der auf dem Typenschild angezeigte Nennwert des  
Gerätes für den Anschluß an das Netz beachtet werden.  
VORSICHT: RAHMENEINBAU  
Die Geräte müssen so in den Rahmen montiert werden, daß keine Gefahren  
durch unebenen inbau des Rahmens verursacht werden.  
Lithium-Batterie - Sollte nur von einem geschulten qualifizierten Techniker  
ausgetauscht werden.  
VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Nur  
mit einer gleichen Batterie oder einem gleichwertigen Batterietyp nach  
Empfehlung des Herstellers ersetzen. Gebrauchte Batterien nach Anweisungen  
des Herstellers beseitigen.  
ALLE LÄNDER: Installation muß örtlichen und nationalen elektrischen  
Vorschriften entsprechen.  
Maschinenlärminformations-Verordnung - 3. GPSGV, der höchste  
Schalldruckpegel beträgt 70dB(A) oder weniger gemäss EN ISO 7779  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation & Safety Guide  
23  
Sikkerhed  
ADVARSEL: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse.  
Bliver det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige  
foranstaltninger.  
ADVARSEL Laserprodukt av klasse 1.  
ADVARSEL Stirr ikke på strålen.  
ELEKTRISKE FORHOLDSREGLER  
ADVARSEL: RISIKO FOR ELEKTRISK STØD  
For at forebygge ELEKTRISK stød, undlad at åbne apparatet. Der er ingen indre  
dele, der kan repareres af brugeren. Denne enhed indeholder LIVSFARLIGE  
STRØMSPÆNDINGER og bør kun åbnes af en uddannet og kvalificeret tekniker.  
FARE UNDER UVEJR  
FARE: UNDLAD at arbejde på udstyr eller KABLER i perioder med  
LYNAKTIVITET.  
ADVARSEL: DEN STRØMFØRENDE LEDNING BRUGES TIL AT AFBRYDE  
STRØMMEN. SKAL STRØMMEN TIL APPARATET AFBRYDES, tages ledningen  
ud af stikket.  
ELEKTRISK - KLASSE 1-UDSTYR  
DETTE UDSTYR KRÆVER JORDFORBINDELSE. Stikket skal være forbundet  
med en korrekt installeret jordforbunden stikkontakt. En ukorrekt installeret  
stikkontakt kan sætte livsfarlig spænding til tilgængelige metaldele.  
UDSTYR TIL STIKKONTAKT, stikkontakten bør installeres nær ved udstyret og  
skal være lettilgængelig.  
ADVARSEL: Ventilationsåbninger må ikke blokeres og skal have fri adgang til den  
omgivende luft i rummet for afkøling.  
BETJENINGSTEMPERATUR: Dette apparat er konstrueret til en omgivende  
temperatur på maksimum 40 grader C.  
ELEKTRISK-OVERBELASTNING AF SPÆNDINGSKREDSLØBET  
Ved installation af produktet, bør der tages hensyn til den kumulative kapacitet  
der angives på navneskiltet, når udstyret forbindes med vekselstrømsledningen.  
ADVARSEL: MEKANISK OPSTILLING-Udstyret skal opstilles i stativet, på en  
sådan måde, at der kke opstår fare p.g.a. ujævn opstilling.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
24  
AT-8600 Series Switch  
Lithium batteri - Bør kun udskiftes af uddannet og kvalificeret tekniker.  
ADVARSEL : Eksplosionsfare, hvis batteriet udskiftes ukorrekt. Udskift kun med  
samme eller en tilsvarende type der anbefales af producenten. Kassér brugte  
batterier i overensstemmelse med producentens instruktioner.  
ALLE LANDE: Installation af produktet skal ske i overensstemmelse med lokal  
og national lovgivning for elektriske installationer.  
Veiligheid  
WAARSCHUWING: Binnenshuis kan dit product radiostoring veroorzaken, in  
welk geval de gebruiker verplicht kan worden om gepaste maatregelen te  
nemen.  
WAARSHUWING Klasse-1 laser produkt.  
WAARCHUWING Neit in de straal staren.  
WAARSCHUWINGEN MET BETREKKING TOT ELEKTRICITEIT  
WAARSCHUWING: GEVAAR VOOR ELEKTRISCHE SCHOKKEN  
Verwijder het deksel niet, teneinde ELEKTRISCHE schokken te voorkomen.  
Binnenin bevinden zich geen onderdelen die door de gebruiker onderhouden  
kunnen worden. Dit toestel staat onder GEVAARLIJKE SPANNING en mag  
alleen worden geopend door een daartoe opgeleide en bevoegde technicus.  
GEVAAR VOOR BLIKSEMINSLAG  
GEVAAR: NIET aan toestellen of KABELS WERKEN bij BLIKSEM.  
WAARSCHUWING: HET TOESTEL WORDT UITGESCHAKELD DOOR DE  
STROOMKABEL TE ONTKOPPELEN.OM HET TOESTEL STROOMLOOS TE  
MAKEN: de stroomkabel ontkoppelen.  
ELEKTRISCHE TOESTELLEN VAN KLASSE 1  
DIT TOESTEL MOET GEAARD WORDEN. De stekker moet aangesloten zijn  
op een juist geaarde contactdoos. Een onjuist geaarde contactdoos kan de  
metalen onderdelen waarmee de gebruiker eventueel in aanraking komt onder  
gevaarlijke spanning stellen.  
AAN TE SLUITEN APPARATUUR, de contactdoos wordt in de nabijheid van de  
apparatuur geïnstalleerd en is gemakkelijk te bereiken.”  
OPGELET: De ventilatiegaten mogen niet worden gesperd en moeten de  
omgevingslucht ongehinderd toelaten voor afkoeling.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation & Safety Guide  
25  
BEDRIJFSTEMPERATUUR: De omgevingstemperatuur voor dit produkt mag niet  
meer bedragen dan 40 graden Celsius.  
ELEKTRISCH: OVERBELASTING VAN WISSELSTROOM HOOFDCIRCUIT  
Tijdens de installatie van het produkt dient men rekening te houden met de  
gecombineerde waarden op de naamplaatjes bij het aansluiten van het toestel op  
de wisselstroom-voedingsdraden.  
LOPGELET: MECHANISCH LADEN - De montage van het toestel in het rek  
dient zo uitgevoerd te worden dat geen gevaar ontstaat door een ongelijke  
lading.  
Lithium batterij. Mag alleen worden vervangen door een daartoe opgeleide en  
bevoegde technicus.  
OPGELET: Gevaar voor ontploffing indien de batterij verkeerd wordt vergangen.  
Alleen vervangen door hetzelfde of een gelijkwaardig, door de fabrikant  
aanbevolen type.  
ALLE LANDEN: het toestel installeren overeenkomstig de lokale en nationale  
elektrische voorschriften.  
Sécurité  
MISE EN GARDE : dans un environnement domestique, ce produit peut  
provoquer des interférences radioélectriques. Auquel cas, l’utilisateur devra  
prendre les mesures adéquates.  
ATTENTION Producit laser di classe 1.  
ATTENTION Ne pas fixer le faisceau des yeux.  
INFORMATION SUR LES RISQUES ÉLECTRIQUES  
AVERTISSEMENT: DANGER D’ÉLECTROCUTION  
Pour éviter toute ÉLECTROCUTION, ne pas ôter le revêtement protecteur du  
matériel. Ce matériel ne contient aucun élément réparable par l’utilisateur. Il  
comprend des TENSIONS DANGEREUSES et ne doit être ouvert que par un  
technicien dûment qualifié.  
DANGER DE FOUDRE  
DANGER: NE PAS MANIER le matériel ou les CÂBLES lors d’activité orageuse.  
ATTENTION: LE CORDON D’ALIMENTATION SERT DE MISE HORS  
CIRCUIT. POUR COUPER L’ALIMENTATION DU MATÉRIEL, débrancher le  
cordon.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
26  
AT-8600 Series Switch  
ÉQUIPEMENT DE CLASSE 1 ÉLECTRIQUE  
CE MATÉRIEL DOIT ÊTRE MIS A LA TERRE. La prise de courant doit être  
branchée dans une prise femelle correctement mise à la terre car des tensions  
dangereuses risqueraient d’atteindre les pièces métalliques accessibles à  
l’utilisateur.  
EQUIPEMENT POUR BRANCHEMENT ELECTRIQUE, la prise de sortie doit  
être placée près de l’équipement et facilement accessible”.  
ATTENTION: Ne pas bloquer les fentes d’aération, ceci empêcherait l’air  
ambiant de circuler librement pour le refroidissement.  
TEMPÉRATURE DE FONCTIONNEMENT: Ce matériel est capable de tolérer  
une température ambiante maximum de ou 40 degrés Celsius.  
SURCHARGE DES CIRCUITS PRINCIPAUX DE COURANT ALTERNATIF  
ÉLECTRIQUE  
Lors de l'installation du matériel, il faut prendre en compte la somme des  
puissances indiquées sur les étiquettes au moment de connecter le matériel à  
une source de courant alternatif.  
ATTENTION : RÉPARTITION DE LA CHARGE MÉCANIQUE - Le montage du  
matériel dans le bâti doit être effectué de telle manière que la répartition de la  
charge mécanique ne pose aucun danger.  
Pile en Lithium-Doit uniquement être remplacée par un technicien dûment  
qualifié  
ATTENTION : Un danger d'explosion existe en cas de remplacement incorrect  
de la pile. Remplacer uniquement avec une pile du même type ou d'un type  
recommandé par le fabricant. Mettre au rebut lespiles usagées conformément  
aux instructions du fabricant).  
POUR TOUS PAYS: Installer le matériel conformément aux normes électriques  
nationales et locales.  
Turvallisuus  
VAROITUS: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä,  
missä tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin  
toimenpiteisiin.  
VAROITUS Luokan 1 Lasertuote.  
VAROITUS Älä katso säteeseen.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation & Safety Guide  
27  
SÄHKÖÖN LIITTYVIÄ HUOMAUTUKSIA  
VAROITUS: SÄHKÖISKUVAARA  
Estääksesi SÄHKÖISKUN älä poista kantta. Sisällä ei ole käyttäjän huollettavissa  
olevia osia. Tämä laite sisältää VAARALLISIA JÄNNITTEITÄ ja sen voi avata vain  
koulutettu ja pätevä teknikko.  
SALAMANISKUVAARA  
HENGENVAARA: ÄLÄ TYÖSKENTELE laitteiden tai KAAPELEIDEN KANSSA  
SALAMOINNIN AIKANA.  
HUOMAUTUS: VIRTAJOHTOA KÄYTETÄÄN  
VIRRANKATKAISULAITTEENA. VIRTA KATKAISTAAN irrottamalla virtajohto.  
SÄHKÖ - TYYPPILUOKAN 1 LAITTEET  
TÄMÄ LAITE TÄYTYY MAADOITTAA. Pistoke täytyy liittää kunnollisesti  
maadoitettuun pistorasiaan. Virheellisesti johdotettu pistorasia voi altistaa  
metalliosat vaarallisille jännitteille.  
PISTORASIAAN KYTKETTÄVÄ LAITE; pistorasia on asennettava laitteen lähelle  
ja siihen on oltava esteetön pääsy.”  
HUOMAUTUS: Ilmavaihtoreikiä ei pidä tukkia ja niillä täytyy olla vapaa yhteys  
ympäröivään huoneilmaan, jotta ilmanvaihto tapahtuisi.  
KÄYTTÖLÄMPÖTILA: Tämä tuote on suunniteltu ympäröivän ilman  
maksimilämpötilalle 40°C.  
SÄHKÖ-VAIHTORVIRTASÄHKÖPIIRIN YLIKUORMITUS  
Tuotetta asennettaessa on otettava huomioon osien nimikilvissä osoitettu teho  
silloin kun osat liitetetään vaihtovirtaverkkoon.  
HUOMAUTUS: MEKAANINEN KUORMITUS--Osien asennuksen alustaan  
tulee tapahtua siten, että epätasainen kuormitus ei aiheuta vaaraa.  
Litiumparisto - Vaihdon voi suorittaa vain koulutettu ja pätevä teknikko.  
Varoitus: Räjähdysvaara, jos paristo on vaihdettu väärin. Vaihda vain samaan tai  
vastaavaan tyyppiin, jota valmistaja suosittelee. Hävitä käytetyt paristot  
valmistajan ohjeiden mukaan.  
KAIKKI MAAT: Asenna tuote paikallisten ja kansallisten  
sähköturvallisuusmääräysten mukaisesti.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
28  
AT-8600 Series Switch  
Norme di Sicurezza  
AVVERTENZA: in ambiente domestico questo prodotto potrebbe causare radio  
interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli  
adeguati provvedimenti.  
AVVERTENZA Prodotto laser di Classe 1.  
AVERTENZA Non fissare il raggio con gli occhi.  
AVVERTENZE ELETTRICHE  
ATTENZIONE: PERICOLO DI SCOSSE ELETTRICHE  
Per evitare SCOSSE ELETTRICHE non asportare il coperchio. Le componenti  
interne non sono riparabili dall’utente. Questa unità ha TENSIONI  
PERICOLOSE e va aperta solamente da un tecnico specializzato e qualificato.  
PERICOLO DI FULMINI  
PERICOLO: NON LAVORARE sul dispositivo o sui CAVI durante  
PRECIPITAZIONI TEMPORALESCHE.  
ATTENZIONE: IL CAVO DI ALIMENTAZIONE È USATO COME  
DISPOSITIVO DI DISATTIVAZIONE. PER TOGLIERE LA CORRENTE AL  
DISPOSITIVO staccare il cavo di alimentazione.  
ELETTRICITÀ - DISPOSITIVI DI CLASSE 1  
QUESTO DISPOSITIVO DEVE AVERE LA MESSA A TERRA. La spina deve  
essere inserita in una presa di corrente specificamente dotata di messa a terra.  
Una presa non cablata in maniera corretta rischia di scaricare una tensione  
pericolosa su parti metalliche accessibili.  
APPARECCHIATURA COLLEGABILE, la presa va installata vicino  
all’apparecchio per risultare facilmente accessibile”.  
ATTENZIONE: le prese d’aria non vanno ostruite e devono consentire il libero  
ricircolo dell’aria ambiente per il raffreddamento.  
TEMPERATURA DI FUNZIONAMENTO: Questo prodotto è concepito per una  
temperatura ambientale massima di 40 gradi centigradi.  
ELETTRICITÀ - SOVRACCARICO DEL CIRCUITO DI RETE A C.A.  
Durante l'installazione ed il collegamento del dispositivo alla rete di  
alimentazione a corrente alternata, è necessario tenere in considerazione le  
capacità cumulative riportate sulla targhetta.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation & Safety Guide  
29  
ATTENZIONE: CARICAMENTO MECCANICO - Il montaggio del dispositivo  
sul supporto va effettuato in maniera tale da evitare qualsiasi potenziale  
condizione di pericolo eventualmente dovuta al montaggio irregolare.  
Batteria al litio - Va sostituita solo da un tecnico specializzato e qualificato.  
ATTENZIONE: l'errata sostituzione della batteria può causare pericolo di  
esplosioni. Sostituire solamente con lo stesso tipo o con uno equivalente  
raccomandato dal produttore. Eliminare le batterie usate secondo le istruzioni  
del produttore.  
TUTTI I PAESI: installare il prodotto in conformità delle vigenti normative  
elettriche nazionali.  
Sikkerhet  
ADVARSEL: Hvis dette produktet benyttes til privat bruk, kan produktet  
forårsake radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige  
forholdsregler.  
ADVARSEL Laserprodukt av klasse 1.  
ADVARSAL Stirr ikke på strålen.  
ELEKTRISITET  
ADVARSEL: FARE FOR ELEKTRISK SJOKK  
For å unngå ELEKTRISK sjokk, må dekslet ikke tas av. Det finnes ingen deler som  
brukeren kan reparere på innsiden. Denne enheten inneholder FARLIGE  
SPENNINGER, og må kun åpnes av en faglig kvalifisert tekniker.  
FARE FOR LYNNEDSLAG  
FARE: ARBEID IKKE på utstyr eller KABLER i TORDENVÆR.  
FORSIKTIG: STRØMLEDNINGEN BRUKES TIL Å FRAKOBLE UTSTYRET. FOR  
Å DEAKTIVISERE UTSTYRET, må strømforsyningen kobles fra.  
ELEKTRISK - TYPE 1- KLASSE UTSTYR  
DETTE UTSTYRET MÅ JORDES. Strømkontakten må være tilkoplet en korrekt  
jordet kontakt. En kontakt som ikke er korrekt jordet kan føre til farlig  
spenninger i lett t ilgjengelige metalldeler.  
UTSTYR FOR STIKKONTAKT. Stikkontakten skal monteres i nærheten av  
utstyret og skal være lett tilgjengelig.”  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
30  
AT-8600 Series Switch  
FORSIKTIG: Lufteventilene må ikke blokkeres, og må ha fri tilgang til luft med  
romtemperatur for avkjøling.  
DRIFTSTEMPERATUR: Dette produktet er konstruert for bruk i maksimum  
romtemperatur på 40 grader celsius.  
ELEKTRISK OVERBELASTNING PÅ AC HOVEDKRETSLØP  
Når produktet installeres, må de samlede navneplateverdiene kontrolleres nøye  
når strøm påsettes.  
FORSIKTIG: MEKANISK LASTNING Installering av utstyret på hyllen må  
utføres på en slik måte at ingen farlige situasjoner oppstår som en følge av ujevn  
lastning.  
Litiumbatteri — Må kun byttes ut av en faglig kvalifisert tekniker.  
FORSIKTIG: Eksplosjonsfare hvis batteriet feilinnsettes.Batteriet må bare  
erstattes med samme type eller en tilsvarende type som er anbefalt av  
fabrikanten. Batteriene må kasseres i samsvar med fabrikantens instruksjoner.  
ALLE LAND: Produktet må installeres i samsvar med de lokale og nasjonale  
elektriske koder.  
Segurança  
AVISO: Num ambiente doméstico este produto pode causar interferência na  
radiorrecepção e, neste caso, pode ser necessário que o utente tome as  
medidas adequadas.  
AVISO Produto laser de classe 1  
AVISO Não olhe fixamente para o raio.  
AVISOS SOBRE CARACTERÍSTICAS ELÉTRICAS  
ATENÇÃO: PERIGO DE CHOQUE ELÉTRICO  
Para evitar CHOQUE ELÉTRICO, não retire a tampa. Não contém peças que  
possam ser consertadas pelo usuário. Este aparelho contém VOLTAGENS  
PERIGOSAS e só deve ser aberto por um técnico qualificado e treinado.  
PERIGO DE CHOQUE CAUSADO POR RAIO  
PERIGO: NÃO TRABALHE no equipamento ou nos CABOS durante períodos  
suscetíveis a QUEDAS DE RAIO.  
CUIDADO: O CABO DE ALIMENTAÇÃO É UTILIZADO COMO UM  
DISPOSITIVO DE DESCONEXÃO. PARA DESELETRIFICAR O  
EQUIPAMENTO, desconecte o cabo de ALIMENTAÇÃO.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation & Safety Guide  
ELÉTRICO - EQUIPAMENTOS DO TIPO CLASSE 1  
31  
DEVE SER FEITA LIGAÇÃO DE FIO TERRA PARA ESTE EQUIPAMENTO. O  
plugue de alimentação deve ser conectado a uma tomada com adequada ligação  
de fio terra. Tomadas sem adequada ligação de fio terra podem transmitir  
voltagens perigosas a peças metálicas expostas.  
EQUIPAMENTO DE LIGAÇÃO, a tomada eléctrica deve estar instalada perto  
do equipamento e ser de fácil acesso.”  
CUIDADO: As aberturas de ventilação não devem ser bloqueadas e devem ter  
acesso livre ao ar ambiente para arrefecimento adequado do aparelho.  
TEMPERATURA DE FUNCIONAMENTO: Este produto foi projetado para uma  
temperatura ambiente máxima de 40 graus centígrados.  
ELÉTRICO - SOBRECARGA DA REDE DE CORRENTE ALTERNADA (AC)  
Antes de instalar o produto, verifique o efeito cumulativo da conexão de  
diversos aparelhos àrede de corrente alternada através das etiquetas que  
indicam potência ou amperagem.  
CUIDADO: CARREGAMENTO - O equipamento deverá ser montado no  
suporte de montagem de forma tal que não cause perigo devido a carregamento  
não uniforme.  
Bateria de lítio - Só deve ser trocada por técnico qualificado e treinado.  
CUIDADO: Se a bateria não for devidamente instalada há perigo de explosão.  
Substitua somente pelo mesmo tipo ou equivalente, conforme recomendado  
pelo fabricante. Descarte baterias usadas, de acordo com as instruções  
fornecidas pelo fabricante.  
TODOS OS PAÍSES: Instale o produto de acordo com as normas nacionais e  
locais para instalações elétricas.  
Seguridad  
ADVERTENCIA: en un entorno doméstico, este producto puede causar  
radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las  
medidas que sean convenientes al respecto.  
¡ADVERTENCIA! Producto láser Clase 1.  
¡ADVERTENCIA! No mirat fijamente el haz.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
32  
AT-8600 Series Switch  
AVISOS ELECTRICOS  
ADVERTENCIA: PELIGRO DE ELECTROCHOQUE  
Para evitar un ELECTROCHOQUE, no quite la tapa. No hay ningún  
componente en el interior al cual puede prestar servicio el usuario. Esta unidad  
contiene VOLTAJES PELIGROSOS y sólo deberá abrirla un técnico entrenado y  
calificado.  
PELIGRO DE RAYOS  
PELIGRO: NO REALICE NINGUN TIPO DE TRABAJO O CONEXION en los  
equipos o en LOS CABLES durante TORMENTAS ELECTRICAS.  
ATENCION: EL CABLE DE ALIMENTACION SE USA COMO UN  
DISPOSITIVO DE DESCONEXION. PARA DESACTIVAR EL EQUIPO,  
desconecte el cable de alimentación.  
ELECTRICO - EQUIPO DEL TIPO CLASE 1  
ESTE EQUIPO TIENE QUE TENER CONEXION A TIERRA. El cable tiene que  
conectarse a un enchufe a tierra debidamente instalado. Un enchufe que no está  
correctamente instalado podría ocasionar tensiones peligrosas en las partes  
metálicas que están expuestas.  
EQUIPO CONECTABLE, el tomacorriente se debe instalar cerca del equipo, en  
un lugar con acceso fácil”.  
ATENCION: Las aberturas para ventilación no deberán bloquearse y deberán  
tener acceso libre al aire ambiental de la sala para su enfriamiento.  
TEMPERATURA REQUERIDA PARA LA OPERACIÓN: Este producto está  
diseñado para una temperatura ambiental máxima de 40 grados C.  
ELECTRICO - SOBRECARGA DEL CIRCUITO PRIMARIO DE CORRIENTE  
ALTERNA  
Al instalarse el producto deberán considerarse las potencias nominales  
acumulativas, cuando se conecta el equipo al cable de alimentación de corriente  
alterna.  
ATENCION: CARGA MECANICA - El montaje del equipo en el bastidor debe  
realizarse de manera tal que no cause una condición peligrosa debido a la  
distribución desigual del peso.  
Batería de litio - Sólo deberá ser cambiada por un técnico entrenado y calificado.  
ATENCION: Peligro de explosión si la batería no se reemplaza en forma  
correcta. Reemplace sólo con el mismo tipo o equivalente que recomienda el  
fabricante. Deseche las baterías usadas según las instrucciones del fabricante.  
PARA TODOS LOS PAÍSES: Monte el producto de acuerdo con los Códigos  
Eléctricos locales y nacionales.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation & Safety Guide  
33  
Säkerhet  
VARNING: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket  
kan tvinga användaren till att vidtaga erforderliga åtgärder.  
VARNING! Laserprodukt av klass 1.  
VARNING! Laserstrålning när enheten är öppen.  
TILLKÄNNAGIVANDEN BETRÄFFANDE ELEKTRICITETSRISK:  
RISK FÖR ELEKTRISK STÖTFör att undvika ELEKTRISK stöt, ta ej av locket.  
Det finns inga delar inuti som behöver underhållas. Denna apparat är under  
HÖGSPÄNNING och får endast öppnas av en utbildad kvalificerad tekniker.  
FARA FÖR BLIXTNEDSLAG  
FARA: ARBETA EJ på utrustningen eller kablarna vid ÅSKVÄDER.  
VARNING: NÄTKABELN ANVÄNDS SOM STRÖMBRYTARE FÖR ATT  
KOPPLA FRÅN STRÖMMEN, dra ur nätkabeln.  
ELEKTRISKT - TYP KLASS 1 UTRUSTNING  
DENNA UTRUSTNING MÅSTE VARA JORDAD. Nätkabeln måste vara  
ansluten till ett ordentligt jordat uttag. Ett felaktigt uttag kan göra att närliggande  
metalldelar utsätts för högspänning. Apparaten skall anslutas till jordat uttag, när  
den ansluts till ett nätverk.  
UTRUSTNING MED PLUGG. Uttaget skall installeras i utrustningens närhet och  
vara lättåtkomligt”.  
VARNING: Luftventilerna får ej blockeras och måste ha fri tillgång till omgivande  
rumsluft för avsvalning.  
DRIFTSTEMPERATUR: Denna produkt är konstruerad för rumstemperatur ej  
överstigande 40 grader Celsius.  
ELEKTRISKT - ÖVERBELASTNING AV VÄXELSTRÖMSNÄTET: När  
produkten installeras bör den sammanlagda effekten på namnplåten beaktas när  
apparaten ansluts till växelströmsnätet.  
VARNING: MEKANISK BELASTNING: Utrustningen ska installeras i chassit på  
så sätt att fara inte uppstår p g a ojämn belastning.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
34  
AT-8600 Series Switch  
Litium batteri - Får endast bytas av utbildade och kvalificerade tekniker.  
VARNING: Risk för explosion om felaktigt batteri används. Byt endast mot  
samma eller likvärdig typ batteri, rekommenderat av tillverkaren. Kassera  
använda batterier i enlighet med tillverkarens instruktioner.  
ALLA LÄNDER: Installera produkten i enlighet med lokala och statliga  
bestämmelser för elektrisk utrustning.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation & Safety Guide  
35  
EC Declaration of Conformity  
We:  
ALLIED TELESIS LABS LIMITED  
27 NAZARETH AVENUE  
CHRISTCHURCH 8024  
NEW ZEALAND  
Declare under our sole legal responsibility that the following product meets the  
safety, protection and conformity requirements of council directives 73/23/EEC  
as amended by 93/68/EEC, and 89/336/EEC as amended by 93/68/EEC, 92/31/  
EEC and 91/263/EEC, on the approximation of the laws of member states  
relating to electromagnetic compatibility and electrical safety.  
AT-8600 SERIES SWITCHES  
to which this declaration relates are in conformity with the following relevant  
harmonized standards, the reference numbers of which have been published in  
the Official journal of the European community.  
EN55022: 1998  
Information Technology Equipment—Radio disturbance  
Incl A1:2000 and A2:2003  
EN55024: 1998  
Incl A1:2001 and A2:2003  
Information Technology Equipment—Immunity characteristics—  
Limits and methods of measurement.  
EN60950-1: 2001  
Information Technology Equipment including electrical business  
equipment—General Requirements.  
EN60825-1: 1994  
Incl A1:2002 and A2:2001  
Safety of Laser Products - part 1: Equipment classification,  
requirements and user’s guide.  
EN61000-3-2: 2000  
Electromagnetic compatibility (EMC) - part 3-2: Limits for  
harmonic current emissions (equipment input current up to and  
including 16A per phase).  
EN61000-3-3: 1995  
Incl A1:2001  
Electromagnetic compatibility (EMC) - part 3-3: Limitation of  
voltage fluctuations and flicker in low-voltage supply systems for  
equipment with rated current up to 16A.  
Name: John Shields  
On behalf of the Manufacturer  
Position: Managing Director  
Date: 2nd August 2006  
Signature:  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Download from Www.Somanuals.com. All Manuals Search And Download.  

3Com Switch 3CR16708 91 User Manual
8e6 Technologies Network Card ER3 100 5K02 55 User Manual
Abbott Diabetes Care Blood Glucose Meter ART06986 User Manual
Accusplit Heart Rate Monitor AX740SBL User Manual
ADIC Digital Camera 601355 Rev A User Manual
AEG Cooktop 41056VH MN User Manual
Alienware Laptop M17X R4 User Manual
Altinex Network Card MT106 101 User Manual
Behringer Music Pedal OD300 User Manual
Disney Interactive Studios Video Games High School Musical Sing It User Manual