Alliance Laundry Systems Washer HWTB21 User Manual
NetMaster  
Topload Washer  
Refer to Page 7 for Model Numbers  
Keep These Instructions for Future Reference.  
(If this machine changes ownership, this manual must accompany machine.)  
Part No. 210140R2  
October 2006  
www.comlaundry.com  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE: The WARNING and IMPORTANT  
instructions appearing in this manual are not meant  
to cover all possible conditions and situations that  
may occur. It must be understood that common  
sense, caution, and carefulness are factors which  
cannot be built into these washers. These factors  
MUST BE supplied by the person(s) installing,  
maintaining, or operating the washer.  
WARNING  
Failure to install, maintain, and/or operate  
this machine according to the  
manufacturer's instructions may result in  
conditions which can produce bodily injury  
and/or property damage.  
W030  
Always contact the distributor, service agent, or the  
manufacturer about any problems or conditions you do  
not understand.  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
210140  
1
Notes  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
210140  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model Identification ...........................................................................  
Preliminary Information....................................................................  
About the Control .................................................................................  
Glossary of Terms.................................................................................  
Power Failure Recovery .......................................................................  
Communications...................................................................................  
Infra-red Communications (Optional)..................................................  
7
9
9
9
9
9
9
Table of  
Contents  
NetMaster Identification.................................................................... 11  
Select Cycle Pads.................................................................................. 11  
Select Wash Temp Pads........................................................................ 11  
VFD Display Identification................................................................ 13  
Light Emitting Diodes (LEDs) ............................................................. 13  
Washer Operation .............................................................................. 15  
Start Up................................................................................................. 15  
Ready Mode.......................................................................................... 15  
Cycle Sequence..................................................................................... 15  
Opening the Washer Lid....................................................................... 15  
Signals................................................................................................... 15  
Changing Cycles................................................................................... 15  
NetMaster Special Features............................................................... 17  
Programming NetMaster ...................................................................... 17  
Collecting Audit Information ............................................................... 17  
Testing Machine and NetMaster Functions.......................................... 17  
Sales Floor Feature ............................................................................... 17  
Rapid Advance Feature......................................................................... 17  
Clearing the NetMaster Vend Feature .................................................. 17  
Communications Mode......................................................................... 17  
Coin Drop ............................................................................................. 17  
Start Pulse Operation ............................................................................ 18  
Service Door and Coin Vault Openings ............................................... 18  
Break-In Alarm..................................................................................... 18  
Special Vend......................................................................................... 18  
Lucky Cycle.......................................................................................... 18  
Site Code Pricing.................................................................................. 18  
Special Cycle ........................................................................................ 18  
Opening the Service Door  
(Coin Models Only)............................................................................. 19  
Entering the Manual Mode................................................................ 21  
How to Enter the Manual Mode ........................................................... 21  
Programming NetMaster ................................................................... 23  
What Can Be Programmed? ................................................................. 23  
Programmable Options Available......................................................... 23  
1. Audio Signal “+001” ................................................................... 24  
2. Reg. Hot Wash Vend Price “+002” ............................................ 26  
3. Reg. Warm Wash Vend Price “+003” ........................................ 28  
4. Reg. Cold Wash Vend Price “+004” ........................................... 30  
5. Site Code #1 Hot Wash Vend Price “+005” ............................... 32  
6. Site Code #1 Warm Wash Vend Price “+006” ........................... 34  
7. Site Code #1 Cold Wash Vend Price “+007” ............................. 36  
8. Special Cycle Vend Price “+008” ............................................... 38  
9. Special Vend A Days Enable “+009” ......................................... 40  
10. Special Vend A Start Hour “+010” ............................................. 45  
11. Special Vend A Length in Hours “+011” ................................... 46  
12. Special Vend A Start Month “+012” .......................................... 47  
13. Special Vend A Start Date “+013” ............................................. 48  
14. Special Vend A End Month “+014” ........................................... 49  
15. Special Vend A End Date “+015” .............................................. 50  
© Copyright 2006, Alliance Laundry Systems LLC  
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any  
means without the expressed written consent of the publisher.  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
210140  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
16. Special Vend A Site Code #1 “+016” ......................................... 51  
17. Special Vend A Reg. Hot Wash Vend Price “+017” .................. 53  
18. Special Vend A Reg. Warm Wash Vend Price “+018” .............. 55  
19. Special Vend A Reg. Cold Wash Vend Price “+019” ................ 57  
20. Special Vend A Auto-Shutdown Enable “+020” ........................ 59  
21. Coin #1 Value “+021” ................................................................ 60  
22. Coin #2 Value “+022” ................................................................ 62  
23. Start Pulse Value “+023” ............................................................ 64  
24. Default Cycle/Temperature “+024” ............................................ 66  
25. Power Fail Reset “+025” ............................................................ 68  
26. Set Real-Time Clock Minutes “+026” ........................................ 70  
27. Set Real-Time Clock Hours “+027” ........................................... 71  
28. Set Real-Time Clock Day “+028” .............................................. 72  
29. Set Real-Time Clock Date “+029” ............................................. 73  
30. Set Real-Time Clock Month “+030” .......................................... 74  
31. Set Real-Time Clock Year “+031” ............................................. 75  
32. Set Real-Time Clock Century “+032” ........................................ 76  
33. Normal Wash Agitate Time “+033” ........................................... 77  
34. Normal Extra Rinse Agitate Time “+034” .................................. 78  
35. Normal Rinse Agitate Time “+035” ........................................... 79  
36. Normal Final Spin Time “+036” ................................................. 80  
37. Permanent Press Wash Agitate Time “+037” ............................. 81  
38. Permanent Press Extra Rinse Agitate Time “+038” ................... 82  
39. Permanent Press Rinse Agitate Time “+039” ............................. 83  
40. Permanent Press Final Spin Time “+040” .................................. 84  
41. Delicate Wash Agitate Time “+041” .......................................... 85  
42. Delicate Extra Rinse Agitate Time “+042” ................................ 86  
43. Delicate Rinse Agitate Time “+043” .......................................... 87  
44. Delicate Final Spin Time “+044” ............................................... 88  
45. Warm Rinse Enable/Disable “+045” .......................................... 89  
46. Control Configuration Data #1 “+046” ....................................... 90  
47. Control Configuration Data #3 “+047” ....................................... 94  
48. Lucky Option “+048” ................................................................. 96  
49. Special Cycle Option “+049” ...................................................... 97  
50. Special Cycle Extra Wash Time “+050” .................................... 99  
51. Special Cycle Extra Extra-Rinse Time “+051” .......................... 100  
52. Smart Card Maximum Value “+052” ......................................... 101  
53. Site Code #1 “+053” ................................................................... 103  
54. Error Code Programming Parameter “+054” .............................. 105  
55. Start Pulse Mode “+055” ............................................................ 107  
Collecting Audit Information ............................................................ 109  
Manual Reset....................................................................................... 111  
Testing Machine and  
Electronic Control Functions............................................................. 113  
Diagnostic Test Descriptions................................................................ 114  
Error Codes......................................................................................... 117  
Sales Floor Feature............................................................................. 121  
Rapid Advance Feature...................................................................... 123  
Clear Vend Feature ............................................................................ 125  
Power Fail Recovery........................................................................... 127  
Power Fail Reset Disabled.................................................................... 127  
Power Fail Reset Enabled..................................................................... 127  
Communications Mode ...................................................................... 129  
Infra-red Communications.................................................................... 129  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
210140  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Card Reader Communications  
(Card Models Only)............................................................................ 129  
Network Communications.................................................................... 129  
Default Washer Settings..................................................................... 131  
Default Settings .................................................................................... 131  
Default Cycle........................................................................................ 131  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
210140  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Notes  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
210140  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model Identification  
Information in this manual is applicable to these washer  
models:  
HWTB21  
HWTF21  
NWTF21  
SWLB20  
SWLB21  
SWLF20  
SWLF21  
SWTA21  
SWTBA0  
SWTBA1  
SWTB20  
SWTB21  
SWTC20  
SWTC21  
SWTF20  
SWTF21  
SWTH20  
SWTH21  
SWTJ21  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Notes  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Preliminary Information  
move to the Rinse Spin cycle and prompt the user to  
press the START pad. Once the START pad is  
pressed, the control will spin out the cycle.  
About the Control  
NetMaster on the commercial washer is an advanced,  
programmable computer that lets the owner control  
most machine features by pressing a sequence of  
SELECT CYCLE and SELECT WASH TEMP pads.  
Refer to Figure 1.  
Communications  
NetMaster may be programmed manually, by the  
Micro-Wand IIIE™, by the Network, or by a Smart  
Card.  
NetMaster allows the owner to program custom  
cycles, set vend prices, retrieve audit information,  
program and run diagnostic cycles, and program  
special vend features. Washers shipped from the  
factory have a default cycle and wash temperature  
setting of PERM PRESS, WARM built in. However,  
the owner can change the default cycle, or any cycle,  
as needs permit.  
Infra-red Communications  
(Optional)  
The Micro-Wand allows the owner to program and  
retrieve information from NetMaster without touching  
the keypad. The Micro-Wand greatly expands the  
programming options available to the owner. However,  
the Micro-Wand is not required to program and operate  
the washer. The operation of the Micro-Wand and the  
advanced features available are covered separately in  
IMPORTANT: In the event of a power failure,  
NetMaster will not have to be reprogrammed. It is  
designed with a memory system that will remember  
how it was programmed (for a minimum of six  
years) until the electrical power is restored.  
™
the Micro-Wand IIIE instruction manual.  
Smart Card Reader Communications  
(Card Models Only)  
IMPORTANT: It is extremely important that the  
washer has a positive ground and that all mechanical  
and electrical connections to NetMaster are made  
before applying power to or operating the washer.  
The control will accept communication with a Card  
Reader in order to perform vending transactions when  
a card is inserted to pay for cycles. The card reader can  
also allow the owner to program and collect audit  
information.  
Glossary of Terms  
The following are a few terms and abbreviations to  
learn. These are referred to throughout the instructions.  
For detailed information on Smart Card Reader  
Communications, refer to the Smart Card Setup  
Module in the NetMaster Smart Card Suite software  
package.  
VFD - Vacuum Fluorescent Display.  
This term refers to the window area of the  
control that displays words and values.  
Network Communications  
LED - Light Emitting Diode.  
This term refers to the lights on the keypads  
and status words of the control.  
The control will also accept communication with a  
Network Interface Board which allows the control to  
be linked to a personal computer. This network link  
allows an owner to program, collect data and run  
diagnostics on any machine.  
Power Failure Recovery  
If a cycle is in progress and the power fails, the cycle  
status is saved in memory for a minimum of six years  
without power. When the power recovers, the washer  
will resume into the previously active cycle if so  
programmed by the owner.  
For detailed information on Network Communications,  
refer to the Network instruction manual.  
The owner may program a special feature called  
POWER FAIL RESET which sets a maximum power  
failure duration. To program this feature, refer to  
Programming NetMaster, option 25.  
If the length of the power failure is greater than the  
POWER FAIL RESET time, the control will end the  
cycle and the display will revert back to the ready  
mode. If the washtub is full of water, the control will  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
Notes  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NetMaster Identification  
Select Cycle Pads  
(Refer to Figure 1)  
Select Wash Temp Pads  
(Refer to Figure 1)  
SELECT CYCLE pads are used to select the specific  
washer cycle. These pads include NORMAL, PERM  
PRESS, and DELICATES. These pads allow the user  
to select a cycle other than the default cycle (PERM  
PRESS). The SELECT CYCLE keypads are not active  
after the first fill cycle of the washer. The selected  
cycle is indicated by the light (LED) on the pad.  
Pressing the START pad will confirm the selection  
and the cycle will begin. When the Smart Card is used,  
the START pad flashes. Pressing the START pad will  
start the cycle and deduct the vend price from the card.  
SELECT WASH TEMP pads are used to select the  
temperature of the water used for the wash fill. These  
pads include HOT, WARM, and COLD. These pads  
allow the user to select a water temperature other than  
the default setting (WARM). The SELECT WASH  
TEMP pads are active only during the first fill cycle of  
the washer. The selected temperature is indicated by  
the light (LED) on the pad.  
Both the SELECT WASH TEMP pads and the SELECT  
CYCLE pads are used in various combinations for  
programming cycles, retrieving audit information,  
running diagnostic tests, and other hidden operations.  
These instructions cover the manual programming and  
data retrieval options.  
Electronic Display Control  
3
2
4
5
6
1
7
C832I  
1
2
3
4
5
6
7
LED Light  
SELECT CYCLE pads (top row)  
Four 7-Segment Digits  
VFD Display  
LED Status Lights  
START pad  
SELECT WASH TEMP pads (bottom row)  
Figure 1  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Notes  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VFD Display Identification  
INSERT COINS/CARD LED  
Light Emitting Diodes (LEDs)  
(Refer to Figure 1)  
INSERT COINS/CARD LED prompts the user for  
coins or a card to satisfy the vend price. Four digits  
and decimal point show the vend price remaining to be  
satisfied. The vend price displayed will decrease with  
each coin inserted. If a new wash temp is selected  
during the first fill of the wash cycle and it requires  
additional vend, the INSERT COINS/CARD light will  
flash one (1) second on and one (1) second off, and the  
display will show the vend price remaining to be  
satisfied.  
LIGHT EMITTING DIODES (LEDs) are used to  
indicate the chosen cycle, wash temperature and cycle  
status. See below for information on each LED.  
CYCLE LED (NORMAL, PERM PRESS or  
DELICATES)  
CYCLE LED will remain lit the entire cycle.  
WASH TEMP LED (HOT, WARM or COLD)  
REMOVE CARD LED (Card Models Only)  
WASH TEMP LED will remain on until the end of the  
cycle or will change to a rinse temperature if programmed  
to do so.  
REMOVE CARD LED flashes one second on and one  
second off after the START pad has been pressed and  
the vend has been deducted from the card. It will also  
flash when a card is inserted and no vend amount is  
required.  
WASH LED  
WASH LED is lit at the beginning of a Wash cycle and  
will remain lit until the wash cycle is complete.  
Four 7-Segment Digits  
RINSE LED  
The 7-SEGMENT DIGITS are used to display the  
time remaining in a cycle, vend price, error messages  
and descriptive codes. When displaying the time  
remaining the colon will flash, and when displaying  
the vend price the decimal point may be lit. During  
diagnostic testing or manual programming of the  
control, these digits will display descriptive codes and  
values (as described in Entering the Manual Mode).  
RINSE LED is lit at the beginning of the Rinse or  
Extra Rinse cycle and will remain lit until the cycle is  
complete.  
SPIN LED  
SPIN LED is lit for all Spin cycles.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
Notes  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Washer Operation  
coin entered after the first fill cycle will be added to  
Start Up  
the total coin counter, but the user will not be able to  
change cycles or water temperature.  
When power is applied to the washer, the control will  
display INSERT COINS/CARD, the decimal point, and  
the vend price. The INSERT COINS/CARD light will  
remain lit until the vend price has been satisfied. The  
default cycle setting is PERM PRESS, the default  
wash water fill temperature is WARM, and the default  
rinse water temperature is COLD. The LEDs will be lit  
on PERM PRESS and WARM at the start of the cycle.  
Refer to Figure 2. These default settings are owner  
programmable. Refer to Programming NetMaster.  
Opening the Washer Lid  
If the washer lid is opened anytime except the last three  
minutes of a cycle, the VFD will display “LId” and the  
timer will stop. Once the lid is closed, the cycle will  
restart from the point of interruption. If the lid is opened  
in the final three minutes of the final spin cycle, the timer  
will continue to count down to the end of the cycle.  
The cycle operation will stop and the VFD will display  
“LId”. When the timer reaches 0 minutes, the control  
will return to the “Ready” mode. Refer to Figure 2.  
Ready Mode  
Signals  
There are four options when a signal can be used during  
the washer operation. These four options are listed below:  
1. End of Cycle Signal  
By default, this signal is turned off. If turned on, the  
signal sounds for three (3) seconds at the end of a  
cycle.  
2. Signal On Keypad Depression  
By default, this signal is turned on and sounds for  
a quarter of a second each time a keypad is pressed.  
3. Signal On Coin Drop/Card Insertion  
By default, this signal is turned on and will sound  
for a quarter of a second each time a coin or card  
is entered.  
C833I  
Figure 2  
To start the cycle, the user must press the START  
keypad.  
4. Signal for Card Removal (Card Models Only)  
By default, this signal is turned on and will sound  
one second on and one second off when the  
REMOVE CARD LED is flashing.  
The user will be able to select a different cycle or wash  
water temperature by pressing a cycle pad when the  
machine is in the ready mode or in the first fill cycle. If  
not enough vend is entered to satisfy the vend price, the  
control will display the remaining vend price needed to  
start the cycle. If the first fill was interrupted to change  
the temperature (which requires more money), and the  
vend price is not satisfied within 1 minute, the washer  
control will go back to the first selection and the cycle  
will restart. After the first fill, all key presses will be  
ignored, allowing the washer to go through the  
complete cycle.  
NOTE: Refer to Programming NetMaster to  
program signal options.  
Changing Cycles  
Cycles and wash temperatures can be changed anytime  
during the first fill cycle. After the first fill cycle, all  
key presses are ignored.  
Selecting a higher priced wash temperature will stop the  
first fill cycle, and INSERT COINS/CARD will flash one  
(1) second on and one (1) second off until the vend price  
has been satisfied. After the vend price has been satisfied,  
the cycle will restart with the new wash temperature. If  
the vend price is not satisfied within 1 minute, the washer  
control will go back to the previously set wash  
temperature.  
When a cycle is complete, the control will display “:00”  
until the lid is opened, a key is pressed, or a coin/card is  
entered. When one of these three options occur, the display  
will revert back to the ready mode. Refer to Figure 2.  
Cycle Sequence  
Upon the start of a cycle, NetMaster will display the  
total cycle time. The appropriate LEDs will light while  
the machine passes through different cycle steps. Any  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15  
 
Notes  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NetMaster Special Features  
Programming NetMaster  
Sales Floor Feature  
NetMaster allows the washer owner to program the  
control with the use of the keypad. Audit, diagnostic,  
cycle and vend information may be programmed and  
retrieved by pressing combinations of the Select Cycle  
and Select Wash Temp pads.  
NetMaster washer has a built-in sales floor routine  
used to display all LED lights and the four digits with  
the colon and decimal point. This function is designed  
to show potential customers the high-tech features of  
NetMaster and to verify that all segments of the VFD  
work.  
For details on programming cycle and vend information,  
refer to Programming NetMaster.  
For detailed information on using the Sales Floor  
feature, refer to Sales Floor Feature.  
Collecting Audit Information  
Rapid Advance Feature  
The control will store audit information in its memory  
that can be retrieved by pressing various combinations  
of Select Cycle and Select Wash Temp pads. NetMaster  
will record coins entered, total wash cycles, and total  
start pulses.  
This feature allows the user to quickly advance  
through active cycles or advance into a cycle from the  
ready mode. This feature is useful when tests must be  
performed immediately on a washer currently in an  
active cycle. In this case, the user can quickly advance  
through the cycles to the ready mode. At this point, the  
user can perform the required tests and then return the  
washer to the point it was interrupted.  
For more information on the audit features, refer to  
Collecting Audit Information.  
NOTE: Additional audit information is retrievable  
with the Micro-Wand IIIE, the Card Reader or the  
Network. Refer to the appropriate instruction  
manual.  
For detailed information on using the Rapid Advance  
feature, refer to Rapid Advance Feature.  
Clearing the NetMaster Vend Feature  
Testing Machine and NetMaster  
Functions  
This feature allows the user to return NetMaster back  
to the ready mode if coins have been entered but the  
full vend price has not yet been satisfied. Refer to  
Figure 2.  
Special programmable diagnostic features built into  
NetMaster allow the owner to run specific diagnostic  
tests. By opening and closing the service door and then  
pressing various sequences of Select Cycle and Select  
Wash Temp pads, the owner may perform the  
following tests:  
For more information on using the Clear Vend feature,  
refer to Clear Vend Feature.  
Communications Mode  
●
●
●
●
●
●
●
●
●
●
●
Control Software Version Number  
Service Door Opening Test  
Coin Vault Opening Test  
Coin Drop #1 Input Test  
Coin Drop #2 Input Test  
Lid Switch Input Test  
Pressure Switch Opening Test  
Show Fill Time Test  
Show Drain Time Test  
This feature allows the washer control to communicate  
with the Micro-Wand IIIE, the Card Reader or the  
Network. This allows the washer control to be  
programmed and have its data read without using the  
keypad.  
For more detailed information on using the  
Communications Mode feature, refer to  
Communications Mode.  
Start Pulse Test  
Configuration Display Tests  
Coin Drop  
For detailed information on running diagnostic tests,  
refer to Testing Machine and NetMaster Functions.  
The control will accept pulses from a single or dual  
coin drop to satisfy vend price. Each coin drop will  
have the ability to start or run a cycle.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
17  
NetMaster Special Features  
Start Pulse Operation  
Lucky Cycle  
The control will accept pulses from a central card  
reader system. The machine can be programmed to  
receive a single start pulse or multiple start pulses, or  
the Start Pulse Option can be turned off. The Start  
Pulse Mode allows the machine to go from the  
“Ready” mode to the “START” mode after single or  
multiple pulses are received.  
This feature allows the owner to program the machine  
to provide a free vend cycle to customers after a  
certain number of cycles have occurred.  
For details on programming the Lucky Cycle Option,  
refer to Programming NetMaster.  
Site Code Pricing  
Service Door and Coin Vault  
Openings  
This feature allows owners to program the control to  
accept site codes for special vending that are specific  
to select groups or individuals when using cards.  
The control will capture the times and dates of the  
openings of the Coin Vault and the Service Door. The  
information is saved in memory. An open service door  
combined with various keypad presses allows the  
control to enter manual modes of operation if the  
Break-In Alarm is not on. These modes include Manual  
Programming, Audit Collection and Diagnostics.  
For details on programming the site code options, refer  
to Programming NetMaster.  
Special Cycle  
This feature allows the owner to offer extra features to  
customers for an added vend price. Features available  
include extra wash time, extra rinse time, and a warm  
rinse temperature.  
Break-In Alarm  
This feature allows the owner to program the machine  
to signal a network alarm if the service door or coin  
vault is opened without disabling the alarm first. To  
avoid the alarm during coin collections, the alarm  
must be disabled.  
For details on programming the Special Cycle option,  
refer to Programming NetMaster.  
Special Vend  
This feature allows the owner to program the control  
to allow programmable vend prices for specific hours  
and dates.  
For details on programming Special Vend, refer to  
Programming NetMaster.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
18  
Opening the Service Door  
(Coin Models Only)  
Manually programming NetMaster requires the user to  
NOTE: For card models, the manual programming  
option is accessed by disconnecting and reconnecting  
a plug behind the control panel, or by inserting the  
appropriate card into the card reader.  
open and close the service door. Opening and closing  
the service door trips a switch allowing access to  
various programming options, diagnostics and audit  
capabilities.  
The service door is located on the top of the meter case.  
Refer to Figure 3.  
WARNING  
Any disassembly requiring the use of tools  
must be performed by a suitably qualified  
service person.  
W299  
SERVICE DOOR  
W521IE1A  
Figure 3  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
19  
 
Notes  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Entering the Manual Mode  
For programming, testing, and retrieving information  
from NetMaster, it is often necessary to enter the  
Manual Mode by following the four simple steps below.  
Manual Mode is broken into two groups: Manual  
Programming and Manual Rapid Advance/Diagnostics.  
Manual Programming can only be turned on or off  
with the Micro-Wand IIIE, the Smart Card Reader or  
the Network. Refer to the appropriate instruction  
manual. Manual Rapid Advance/Diagnostics can be  
turned on and off using the Micro-Wand IIIE, by  
manual programming (refer to option 47 of  
How to Enter the Manual Mode  
1. Be sure the washer is in the ready mode before  
continuing to step 2. Refer to Figure 2. If the  
washer is in an active cycle, rapid advance  
through the cycle. Refer to Rapid Advance  
Feature. If coins or a card has been entered, refer  
to Clear Vend Feature.  
Programming NetMaster), with the Smart Card  
Reader, or with the Network.  
By default, both groups are turned “ON”.  
The manual features available in each group are as  
follows (the menu displayed on the VFD in this mode  
is in parenthesis).  
2. Open the service door. Refer to Opening the  
Service Door.  
3. While pressing and holding the NORMAL  
keypad with one hand, press the HOT keypad  
with the other hand.  
Manual Programming  
Manual Programming (PrOg)  
Manual Read Audit (AudT)  
Manual Reset (rSET)  
4. The VFD display will show “rAPd”. Refer to  
Figure 4.  
Rapid Advance/Diagnostics  
Rapid Advance (rAPd)  
Show Mode (SHOW)  
Diagnostic Tests (dIAg)  
If a group is turned “OFF”, the feature menu will still  
appear, but the features in the group cannot be entered.  
C834I  
Figure 4  
5. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the options until the  
desired option appears in the VFD.  
6. Press the START (enter) keypad.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
21  
 
Notes  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programming NetMaster  
What Can Be Programmed?  
OPTION  
019  
020  
021  
022  
023  
024  
025  
026  
027  
028  
029  
030  
031  
032  
033  
034  
035  
036  
037  
038  
039  
040  
041  
042  
043  
044  
045  
046  
047  
048  
049  
050  
051  
052  
053  
054  
055  
DESCRIPTION  
Special Vend A Reg. Cold Wash Vend Price  
Special Vend A Auto-Shutdown Enable  
Coin #1 Value  
This feature allows the owner to program cycle  
parameters, standard vend pricing, special vends and other  
features by using the keypads. The control must have  
the Manual Programming Mode enabled, which is the  
factory default. This mode can only be turned OFF and  
ON by using the Micro-Wand IIIE, the Smart Card  
Reader or the Network. Refer to this section when  
programming NetMaster.  
Coin #2 Value  
Start Pulse Value  
Default Cycle/Temperature  
Power Fail Reset  
This section offers a detailed description of all 55 options  
available to program.  
Set Real-Time Clock Minutes  
Set Real-Time Clock Hours  
Set Real-Time Clock Day  
Set Real-Time Clock Date  
Set Real-Time Clock Month  
Set Real-Time Clock Year  
Set Real-Time Clock Century  
Normal Wash Agitate Time  
Normal Extra Rinse Agitate Time  
Normal Rinse Agitate Time  
Normal Final Spin Time  
Each description includes instructions on when and  
why the option might be used and, more importantly,  
how to program the option.  
For more advanced users, a quick reference list of the  
options available through the programming mode is  
located on this page.  
NOTE: The three numbers in the Option column of  
the Programmable Options list are what will be  
shown in the VFD display when that option is  
selected.  
Programmable Options Available  
Perm Press Wash Agitate Time  
Perm Press Extra Rinse Agitate Time  
Perm Press Rinse Agitate Time  
Perm Press Final Spin Time  
Delicate Wash Agitate Time  
Delicate Extra Rinse Agitate Time  
Delicate Rinse Agitate Time  
Delicate Final Spin Time  
Warm Rinse Enable/Disable  
Control Configuration Data #1  
Control Configuration Data #3  
Lucky Option  
OPTION  
001  
002  
003  
004  
005  
006  
007  
008  
009  
010  
011  
012  
013  
014  
015  
016  
017  
018  
DESCRIPTION  
Audio Signal  
Reg. Hot Wash Vend Price  
Reg. Warm Wash Vend Price  
Reg. Cold Wash Vend Price  
Site Code #1 Reg. Hot Wash Vend Price  
Site Code #1 Reg. Warm Wash Vend Price  
Site Code #1 Reg. Cold Wash Vend Price  
Special Cycle Vend Price  
Special Vend A Days Enable  
Special Vend A Start Hour  
Special Cycle Option  
Special Vend A Length in Hours  
Special Vend A Start Month  
Special Cycle Extra Wash Time  
Special Cycle Extra Extra-Rinse Time  
Smart Card Maximum Value  
Site Code #1  
Special Vend A Start Date  
Special Vend A End Month  
Special Vend A End Date  
Error Code Programming Parameter  
Start Pulse Mode  
Special Vend A Site Code #1  
Special Vend A Reg. Hot Wash Vend Price  
Special Vend A Reg. Warm Wash Vend Price  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programming NetMaster  
4. Locate the desired number in the first column of  
1. Audio Signal “+001”  
Table 1 on the following page.  
This option allows the owner to program when the  
signal will sound.  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
number until correct. Refer to Figure 7.  
There are four occasions when a signal may sound  
during the washer operation. These four occasions are  
listed below:  
1
1. End of Cycle Signal  
By default, the signal is turned off. If turned on,  
the signal will sound for three seconds at the end  
of a cycle.  
2. Keypad Depression Signal  
By default, this signal is turned on and will sound  
for a quarter of a second. This signal will sound  
each time a keypad is pressed.  
3. Coin Input/Card Insertion Signal  
By default, this signal is turned on and will sound  
for a quarter of a second each time a coin or card  
is entered.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
4. Remove Card Signal (Card Models Only)  
By default, this signal is turned on and will sound  
one second on and one second off when the  
REMOVE CARD LED is flashing.  
3
Press this pad (-) to scroll back or decrease a value  
Figure 7  
How to Program the Audio Signal  
For Example: A user might wish to have the signal  
sound only when a keypad is pressed. Entering the  
number “1” in step 5 would turn off all the options  
except KEYPAD. In this instance, the signal would  
sound only when a keypad is pressed.  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad.  
6. Press the START (enter) keypad when the  
correct number appears in the VFD. The next  
option, “+002”, will appear in the VFD.  
NOTE: To program “+002” (Reg. Hot Wash Vend  
Price), refer to option 2. To program other options,  
refer to the appropriate section.  
C762I  
Figure 5  
3. “+001” will appear in the VFD. Press the  
START (enter) keypad. A number will appear in  
the VFD. This number corresponds to the current  
Audio Signal Programming Value.  
C821I  
Figure 6  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
24  
 
Programming NetMaster  
How to Exit Programming Feature  
Signal Remove Coin/Card End of  
Key  
Value  
Card  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
Input  
OFF  
OFF  
OFF  
OFF  
ON  
Cycle  
OFF  
OFF  
ON  
Pressed  
1. Be sure the control shows a programmable  
option, not a value.  
0
OFF  
ON  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
1
2
OFF  
ON  
3
ON  
How to Read Table 1  
4
OFF  
OFF  
ON  
OFF  
ON  
To determine the correct number required to program  
the Audio Signal, use the following chart. The Signal  
Value column contains the number required in step 5.  
The other columns correspond to individual options.  
5
ON  
6
ON  
OFF  
ON  
7
ON  
ON  
Each column of options contains a unique combination  
of the words “ON” and “OFF” that indicates if that  
column’s option is turned on or off when the Signal  
Value is entered. Select the desired combination of  
options and enter the number found in the Signal  
Value column.  
8
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
ON  
9
ON  
10  
11  
12  
13  
14  
15  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
Table 1  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programming NetMaster  
4. When “+002” appears in the VFD, press the  
START (enter) keypad. There are five digits in  
the Reg. Hot Wash Vend Price. The fifth digit  
will appear in the VFD and will flash one second  
on, one second off. Refer to Figure 10.  
2. Reg. Hot Wash Vend Price  
“+002”  
This option allows the owner to set the vend price for a  
hot wash. This vend price will be displayed in the  
VFD when HOT is selected.  
NOTE: If the vend price is $100.00 or more, the  
fifth digit is “1”. If the vend price is $99.99 or less,  
the fifth digit is “0”.  
How to Program the Reg. Hot Wash  
Vend Price  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
C826I  
C826I  
Figure 10  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
fifth digit. Refer to Figure 11.  
NOTE: The vend price can be set from 1 to 65,535.  
C762I  
Figure 8  
1
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+002” appears in the VFD. Refer  
to Figure 9.  
3
2
C860I  
C764I  
C764I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
Figure 9  
3
Press this pad (-) to scroll back or decrease a value  
Figure 11  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Programming NetMaster  
6. Press the START (enter) keypad to enter the fifth  
digit and display remaining four digits. The  
active digit will flash one second on and one  
second off. Refer to Figure 12.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C87
C827I  
Figure 12  
7. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
active digit and the START (enter) keypad to  
enter the value of the digit and advance to the  
next digit.  
8. Press the START (enter) keypad with the last  
active digit. The next option, “+003”, will  
appear in the VFD.  
NOTE: To program “+003” (Reg. Warm Wash  
Vend Price), refer to option 3. To program other  
options, refer to the appropriate section.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
27  
 
Programming NetMaster  
4. When “+003” appears in the VFD, press the  
START (enter) keypad. There are five digits in  
the Reg. Warm Wash Vend Price. The fifth digit  
will appear in the VFD and will flash one second  
on, one second off. Refer to Figure 15.  
3. Reg. Warm Wash Vend Price  
“+003”  
This option allows the owner to set the vend price for a  
warm wash. This vend price will be displayed in the  
VFD when WARM is selected.  
NOTE: If the vend price is $100.00 or more, the  
fifth digit is “1”. If the vend price is $99.99 or less,  
the fifth digit is “0”.  
How to Program the Reg. Warm Wash  
Vend Price  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
C826I  
C826I  
Figure 15  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
fifth digit. Refer to Figure 16.  
NOTE: The vend price can be set from 1 to 65,535.  
C762I  
Figure 13  
1
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+003” appears in the VFD. Refer  
to Figure 14.  
3
2
C860I  
C765I  
C765I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
Figure 14  
3
Press this pad (-) to scroll back or decrease a value  
Figure 16  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Programming NetMaster  
6. Press the START (enter) keypad to enter the fifth  
digit and display remaining four digits. The  
active digit will flash one second on and one  
second off. Refer to Figure 17.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C87
C827I  
Figure 17  
7. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
active digit and the START (enter) keypad to  
enter the value of the digit and advance to the  
next digit.  
8. Press the START (enter) keypad with the last  
active digit. The next option, “+004”, will appear  
in the VFD.  
NOTE: To program “+004” (Reg. Cold Wash  
Vend Price), refer to option 4. To program other  
options, refer to the appropriate section.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
29  
 
Programming NetMaster  
4. When “+004” appears in the VFD, press the  
START (enter) keypad. There are five digits in  
the Reg. Cold Wash Vend Price. The fifth digit  
will appear in the VFD and will flash one second  
on, one second off. Refer to Figure 20.  
4. Reg. Cold Wash Vend Price  
“+004”  
This option allows the owner to set the vend price for a  
cold wash. This vend price will be displayed in the  
VFD when COLD is selected.  
NOTE: If the vend price is $100.00 or more, the  
fifth digit is “1”. If the vend price is $99.99 or less,  
the fifth digit is “0”.  
How to Program the Reg. Cold Wash  
Vend Price  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
C826I  
C826I  
Figure 20  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
fifth digit. Refer to Figure 21.  
NOTE: The vend price can be set from 1 to 65,535.  
C762I  
Figure 18  
1
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+004” appears in the VFD. Refer  
to Figure 19.  
3
2
C860I  
C766I  
C766I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
Figure 19  
3
Press this pad (-) to scroll back or decrease a value  
Figure 21  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Programming NetMaster  
6. Press the START (enter) keypad to enter the fifth  
digit and display remaining four digits. The  
active digit will flash one second on and one  
second off. Refer to Figure 22.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C87
C827I  
Figure 22  
7. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
active digit and the START (enter) keypad to  
enter the value of the digit and advance to the  
next digit.  
8. Press the START (enter) keypad with the last  
active digit. The next option, “+005”, will appear  
in the VFD.  
NOTE: To program “+005” (Site Code #1 Reg. Hot  
Wash Vend Price), refer to option 5. To program  
other options, refer to the appropriate section.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
31  
 
Programming NetMaster  
4. When “+005” appears in the VFD, press the  
START (enter) keypad. There are five digits in  
the Site Code #1 Hot Wash Vend Price. The fifth  
digit will appear in the VFD and will flash one  
second on, one second off. Refer to Figure 25.  
5. Site Code #1 Hot Wash Vend  
Price “+005”  
This option allows the owner to set the vend price for a  
hot wash when cards with a special site code are used  
by specific groups or individuals.  
NOTE: If the vend price is $100.00 or more, the  
fifth digit is “1”. If the vend price is $99.99 or less,  
the fifth digit is “0”.  
How to Program the Site Code #1 Hot  
Wash Vend Price  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
C826I  
C826I  
Figure 25  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
fifth digit. Refer to Figure 26.  
NOTE: The vend price can be set from 0 to 65,535.  
C762I  
Figure 23  
1
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+005” appears in the VFD. Refer  
to Figure 24.  
3
2
C860I  
C835I  
C835I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
Figure 24  
3
Press this pad (-) to scroll back or decrease a value  
Figure 26  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Programming NetMaster  
6. Press the START (enter) keypad to enter the fifth  
digit and display remaining four digits. The  
active digit will flash one second on and one  
second off. Refer to Figure 27.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C87
C827I  
Figure 27  
7. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
active digit and the START (enter) keypad to  
enter the value of the digit and advance to the  
next digit.  
8. Press the START (enter) keypad with the last  
active digit. The next option, “+006”, will  
appear in the VFD.  
NOTE: To program “+006” (Site Code #1 Warm  
Wash Vend Price), refer to option 6. To program  
other options, refer to the appropriate section.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
33  
 
Programming NetMaster  
4. When “+006” appears in the VFD, press the  
START (enter) keypad. There are five digits in  
the Site Code #1 Warm Wash Vend Price. The  
fifth digit will appear in the VFD and will flash  
one second on, one second off. Refer to Figure 30.  
6. Site Code #1 Warm Wash Vend  
Price “+006”  
This option allows the owner to set the vend price for a  
warm wash when cards with a special site code are  
used by specific groups or individuals.  
NOTE: If the vend price is $100.00 or more, the  
fifth digit is “1”. If the vend price is $99.99 or less,  
the fifth digit is “0”.  
How to Program the Site Code #1 Warm  
Wash Vend Price  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
C826I  
C826I  
Figure 30  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
fifth digit. Refer to Figure 31.  
NOTE: The vend price can be set from 0 to 65,535.  
C762I  
Figure 28  
1
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+006” appears in the VFD. Refer  
to Figure 29.  
3
2
C860I  
C836I  
C836I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
Figure 29  
3
Press this pad (-) to scroll back or decrease a value  
Figure 31  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Programming NetMaster  
6. Press the START (enter) keypad to enter the fifth  
digit and display remaining four digits. The  
active digit will flash one second on and one  
second off. Refer to Figure 32.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C87
C827I  
Figure 32  
7. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
active digit and the START (enter) keypad to  
enter the value of the digit and advance to the  
next digit.  
8. Press the START (enter) keypad with the last  
active digit. The next option, “+007”, will  
appear in the VFD.  
NOTE: To program “+007” (Site Code #1 Cold  
Wash Vend Price), refer to option 7. To program  
other options, refer to the appropriate section.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
35  
 
Programming NetMaster  
4. When “+007” appears in the VFD, press the  
START (enter) keypad. There are five digits in  
the Site Code #1 Cold Wash Vend Price. The  
fifth digit will appear in the VFD and will flash  
one second on, one second off. Refer to Figure  
35.  
7. Site Code #1 Cold Wash Vend  
Price “+007”  
This option allows the owner to set the vend price for a  
cold wash when cards with a special site code are used  
by specific groups or individuals.  
NOTE: If the vend price is $100.00 or more, the  
fifth digit is “1”. If the vend price is $99.99 or less,  
the fifth digit is “0”.  
How to Program the Site Code #1 Cold  
Wash Vend Price  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
C826I  
C826I  
Figure 35  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
fifth digit. Refer to Figure 36.  
C762I  
NOTE: The vend price can be set from 0 to 65,535.  
Figure 33  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+007” appears in the VFD. Refer  
to Figure 34.  
1
3
2
C837I  
C837I  
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
Figure 34  
3
Press this pad (-) to scroll back or decrease a value  
Figure 36  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Programming NetMaster  
6. Press the START (enter) keypad to enter the fifth  
digit and display remaining four digits. The  
active digit will flash one second on and one  
second off. Refer to Figure 37.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C87
C827I  
Figure 37  
7. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
active digit and the START (enter) keypad to  
enter the value of the digit and advance to the  
next digit.  
8. Press the START (enter) keypad with the last  
active digit. The next option, “+008”, will appear  
in the VFD.  
NOTE: To program “+008” (Special Cycle Vend  
Price), refer to option 8. To program other options,  
refer to the appropriate section.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
37  
 
Programming NetMaster  
4. When “+008” appears in the VFD, press the  
START (enter) keypad. There are five digits in  
the Special Cycle Vend Price. The fifth digit will  
appear in the VFD and will flash one second on,  
one second off. Refer to Figure 40.  
8. Special Cycle Vend Price  
“+008”  
This option allows the owner to program the machines  
to offer extra features to the customers for an added  
vend price. This vend price will be displayed in the  
VFD for 30 seconds starting 5 seconds after the start  
(refer to option 49) of the first fill/agitate. Refer to  
option 49, 50 and 51 for programming these features.  
NOTE: If the vend price is $100.00 or more, the  
fifth digit is “1”. If the vend price is $99.99 or less,  
the fifth digit is “0”.  
How to Program Special Cycle Vend Price  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
C826I  
Figure 40  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
number until correct. Refer to Figure 41.  
NOTE: The vend price can be set from 1 to 65,535.  
1
C762I  
Figure 38  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+008” appears in the VFD. Refer  
to Figure 39.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
C770I  
C770I  
Figure 41  
6. Press the START (enter) keypad to enter the fifth  
digit and display the remaining four digits. The  
active digit will flash one second on and one  
second off. Refer to Figure 42.  
Figure 39  
C827I  
C827I  
Figure 42  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
38  
         
Programming NetMaster  
7. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
active digit and the START (enter) keypad to  
enter the value of the digit and advance to the  
next digit.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
8. Press the START (enter) keypad with the last  
active digit. The next option, “+009”, will appear  
in the VFD.  
NOTE: To program “+009” (Special Vend A Days  
Enable), refer to option 9. To program other  
options, refer to the appropriate section.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
39  
Programming NetMaster  
4. When “+009” appears in the VFD, press the  
START (enter) keypad. A number will appear in  
the VFD that corresponds to the current Special  
Vend A Days Enable Programming Value.  
9. Special Vend A Days Enable  
“+009”  
This option allows the owner to set the day or days of  
a special vend.  
5. Locate the desired number in the first column of  
Table 2 on the following pages.  
Special Vend A is used to change the standard vend  
prices for special occasions or to turn the machine off.  
The special vend can be programmed to start and end  
on a specific day or days of the week.  
6. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
number until correct. Refer to Figure 45.  
The owner may also turn the Special Vend A option  
on or off if desired.  
1
How to Program Special Vend A Days  
Enable  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
Figure 45  
C762I  
7. Press the START (enter) keypad when the  
correct number appears in the VFD. The next  
option, “+010”, will appear in the VFD.  
Figure 43  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+009” appears in the VFD. Refer  
to Figure 44.  
NOTE: To program “+010” (Special Vend A Start  
Hour), refer to option 10. To program other  
options, refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C771I  
C771I  
Figure 44  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
40  
     
Programming NetMaster  
How to Read Table 2  
To determine the correct number required to program  
the Special Vend A Days Enable, use the following  
table. The “SPA” Value column contains the number  
required in step 6. The other columns correspond to  
individual days.  
Each column of days contains a unique combination of  
the words “ON” and “OFF” that indicates if that  
column’s day is turned on or off when the “SPA”  
value is entered. Select the desired combination of  
days and enter the number found in the “SPA” value  
column.  
“+009”  
WED  
“SPA” VALUE  
SAT  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
FRI  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
THUR  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
TUE  
OFF  
OFF  
OFF  
OFF  
ON  
MON  
OFF  
OFF  
ON  
SUN  
OFF  
ON  
ON/OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
0
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
3
5
OFF  
ON  
7
ON  
9
OFF  
OFF  
ON  
OFF  
ON  
11  
13  
15  
17  
19  
21  
23  
25  
27  
29  
31  
33  
35  
37  
39  
41  
43  
45  
47  
49  
51  
53  
55  
57  
59  
61  
63  
65  
67  
69  
ON  
ON  
OFF  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
OFF  
Table 2  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programming NetMaster  
“+009” (continued)  
“SPA” VALUE  
71  
SAT  
FRI  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
THUR  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
WED  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
TUE  
OFF  
ON  
ON  
ON  
MON  
ON  
OFF  
OFF  
ON  
SUN  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON/OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
73  
75  
77  
79  
81  
83  
85  
87  
89  
91  
93  
95  
97  
99  
101  
103  
105  
107  
109  
111  
113  
115  
117  
119  
121  
123  
125  
127  
129  
131  
133  
135  
137  
139  
141  
143  
145  
147  
149  
151  
153  
155  
157  
159  
161  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
ON  
ON  
OFF  
ON  
ON  
ON  
OFF  
Table 2  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programming NetMaster  
“+009” (continued)  
“SPA” VALUE  
163  
165  
167  
169  
171  
173  
175  
177  
179  
181  
183  
185  
187  
189  
191  
193  
195  
197  
199  
201  
203  
205  
207  
209  
211  
213  
215  
217  
219  
221  
223  
225  
227  
229  
231  
233  
235  
237  
239  
241  
243  
245  
247  
249  
251  
253  
SAT  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
FRI  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
THUR  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
WED  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
TUE  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
MON  
OFF  
ON  
SUN  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON/OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
Table 2  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programming NetMaster  
“+009” (continued)  
“SPA” VALUE  
SAT  
ON  
FRI  
ON  
THUR  
ON  
WED  
ON  
TUE  
ON  
MON  
ON  
SUN  
ON  
ON/OFF  
255  
ON  
Table 2  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the start hour to  
the desired hour. Refer to Figure 48.  
10. Special Vend A Start Hour  
“+010”  
This option allows the owner to set the hour that  
Special Vend A will begin.  
1
How to Program Special Vend A Hour  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
C762I  
Figure 48  
Figure 46  
6. Press the START (enter) keypad when the  
correct hour appears in the VFD. The next option,  
“+011”, will appear in the VFD.  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+010” appears in the VFD. Refer  
to Figure 47.  
NOTE: To program “+011” (Special Vend A  
Length in Hours), refer to option 11. To program  
other options, refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C772I  
Figure 47  
4. When “+010” appears in the VFD, press the  
START (enter) keypad. The current start time (in  
military time) will appear in the VFD.  
NOTE: The hours will be displayed in military  
time.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
45  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current length  
of hours to the desired number of hours. Refer to  
Figure 51.  
11. Special Vend A Length in Hours  
“+011”  
This option allows the owner to set the length in hours  
for Special Vend A.  
1
How to Program Special Vend A Length  
in Hours  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
C762I  
Figure 51  
Figure 49  
6. Press the START (enter) keypad when the  
correct hour appears in the VFD. The next option,  
“+012”, will appear in the VFD.  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+011” appears in the VFD. Refer  
to Figure 50.  
NOTE: To program “+012” (Special Vend A Start  
Month), refer to option 12. To program other  
options, refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
77I  
C773I  
Figure 50  
4. When “+011” appears in the VFD, press the  
START (enter) keypad. The current length in  
hours will appear in the VFD.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
46  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the start month to  
the desired month. Refer to Figure 54.  
12. Special Vend A Start Month  
“+012”  
This option allows the owner to set the month that  
Special Vend A will begin.  
If “0” is selected and Special Vend A is on,  
Special Vend A will occur at the time and days of  
week selected, regardless of the month.  
NOTE: If Special Vend A Start Month, Start Date,  
End Month, or End Date are programmed to zero  
(default is zero), the special Vend A will be active  
every week on the days programmed in option 9.  
1
How to Program Special Vend A Start  
Month  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
Figure 54  
6. Press the START (enter) keypad when the  
correct month appears in the VFD. The next  
option, “+013”, will appear in the VFD.  
C762I  
Figure 52  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+012” appears in the VFD. Refer  
to Figure 53.  
NOTE: To program “+013” (Special Vend A Start  
Date), refer to option 13. To program other options,  
refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
1. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C774I  
Figure 53  
4. When “+012” appears in the VFD, press the  
START (enter) keypad. The current start month  
will appear in the VFD.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
47  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the start date to  
the desired date. Refer to Figure 57.  
13. Special Vend A Start Date  
“+013”  
This option allows the owner to set the date that  
Special Vend A will begin.  
If “0” is selected and Special Vend A is on,  
Special Vend A will occur at the time or days of  
week selected, regardless of the date.  
How to Program Special Vend A Start  
Date  
1
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
C762I  
3
Press this pad (-) to scroll back or decrease a value  
Figure 55  
Figure 57  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+013” appears in the VFD. Refer  
to Figure 56.  
6. Press the START (enter) keypad when the  
correct date appears in the VFD. The next option,  
“+014”, will appear in the VFD.  
NOTE: To program “+014” (Special Vend A End  
Month), refer to option 14. To program other  
options, refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
C775I  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
Figure 56  
4. When “+013” appears in the VFD, press the  
START (enter) keypad. The current start date  
will appear in the VFD.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
48  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the end month to  
the desired month. Refer to Figure 60.  
14. Special Vend A End Month  
“+014”  
This option allows the owner to set the month that  
Special Vend A will end.  
If “0” is selected and Special Vend A is on,  
Special Vend A will occur at the time or day of  
week selected, regardless of the month.  
How to Program Special Vend A End  
Month  
1
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
C762I  
3
Press this pad (-) to scroll back or decrease a value  
Figure 58  
Figure 60  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+014” appears in the VFD. Refer  
to Figure 59.  
6. Press the START (enter) keypad when the  
correct month appears in the VFD. The next  
option, “+015”, will appear in the VFD.  
NOTE: To program “+015” (Special Vend A End  
Date), refer to option 15. To program other options,  
refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
C776I  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
Figure 59  
4. When “+014” appears in the VFD, press the  
START (enter) keypad. The current end month  
will appear in the VFD.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
49  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the end date to the  
desired date. Refer to Figure 63.  
15. Special Vend A End Date “+015”  
This option allows the owner to set the date that  
Special Vend A will end.  
If “0” is selected and Special Vend A is on,  
Special Vend A will occur at the time or days of  
week selected, regardless of the date.  
How to Program Special Vend A End Date  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
1
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
C762I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
Figure 61  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+015” appears in the VFD. Refer  
to Figure 62.  
3
Press this pad (-) to scroll back or decrease a value  
Figure 63  
6. Press the START (enter) keypad when the  
correct date appears in the VFD. The next option,  
“+016”, will appear in the VFD.  
NOTE: To program “+016” (Special Vend A Site  
Code #1), refer to option 16. To program other  
options, refer to the appropriate section.  
How to Exit Programming Feature  
C777I  
1. Be sure the control shows a programmable option,  
not a value.  
Figure 62  
4. When “+015” appears in the VFD, press the  
START (enter) keypad. The current end date will  
appear in the VFD.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
50  
     
Programming NetMaster  
4. When “+016” appears in the VFD, press the  
START (enter) keypad. There are five digits in  
the Special Vend A Site Code #1. The fifth digit  
will appear in the VFD and will flash one second  
on, one second off. Refer to Figure 66.  
16. Special Vend A Site Code #1  
“+016”  
This option allows the owner to program the machines  
to accept site codes for Special Vend A that are  
specific to select groups or individuals when using  
cards. It also allows the owner to only give Special  
Vend A pricing for a card with this site code. If  
Special Vend A site code is zero, then Special Vend A  
pricing will apply to all cards.  
NOTE: If the Special Vend A Site Code #1 price is  
10000 or more, the fifth digit is “1”. If the Special  
Vend A Site Code #1 price is 9999 or less, the fifth  
digit is “0”.  
How to Program the Special Vend A Site  
Code #1  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
C826I  
C826I  
Figure 66  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
fifth digit. Refer to Figure 67.  
NOTE: The coin value can be set from 1 to 65,535.  
1
C762I  
Figure 64  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+016” appears in the VFD. Refer  
to Figure 65.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
C838I  
C838I  
3
Press this pad (-) to scroll back or decrease a value  
Figure 65  
Figure 67  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Programming NetMaster  
6. Press the START (enter) keypad to enter the fifth  
digit and display remaining four digits. The  
active digit will flash one second on and one  
second off. Refer to Figure 68.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C87
C827I  
Figure 68  
7. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
active digit and the START (enter) keypad to  
enter the value of the digit and advance to the  
next digit.  
8. Press the START (enter) keypad with the last  
active digit. The next option, “+017”, will appear  
in the VFD.  
NOTE: To program “+017” (Special Vend A Reg.  
Hot Wash Vend Price), refer to option 17. To  
program other options, refer to the appropriate  
section.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
52  
 
Programming NetMaster  
4. When “+017” appears in the VFD, press the  
START (enter) keypad. There are five digits in  
the Special Vend A Reg. Hot Wash Vend Price.  
The fifth digit will appear in the VFD and will  
flash one second on and one second off. Refer to  
Figure 71.  
17. Special Vend A Reg. Hot Wash  
Vend Price “+017”  
This option allows the owner to set the vend price for a  
Hot Wash in Special Vend A.  
How to Program Special Vend A Reg. Hot  
Wash Vend Price  
NOTE: If the vend price is $100.00 or more, the  
fifth digit is “1”. If the vend price is $99.99 or less,  
the fifth digit is “0”.  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
C826I  
C826I  
Figure 71  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
fifth digit. Refer to Figure 72.  
C762I  
Figure 69  
NOTE: The vend price can be set from 0 to 65,535.  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable options  
until “+017” appears in the VFD. Refer to  
Figure 70.  
1
C795I  
3
2
C860I  
Figure 70  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
Figure 72  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Programming NetMaster  
6. Press the START (enter) keypad to enter the fifth  
digit and display remaining four digits. The  
active digit will flash one second on and one  
second off. Refer to Figure 73.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C88
C828I  
Figure 73  
7. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
active digit and the START keypad to enter the  
value of the digit and advance to the next digit.  
8. Press the START (enter) keypad with the last  
active digit. The next option, “+018”, will appear  
in the VFD.  
NOTE: To program “+018” (Special Vend A Reg.  
Warm Wash Vend Price), refer to option 18. To  
program other options, refer to the appropriate  
section.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
54  
 
Programming NetMaster  
4. When “+018” appears in the VFD, press the  
START (enter) keypad. There are five digits in  
the Special Vend A Reg. Warm Wash Vend  
Price. The fifth digit will appear in the VFD and  
will flash one second on and one second off.  
Refer to Figure 76.  
18. Special Vend A Reg. Warm  
Wash Vend Price “+018”  
This option allows the owner to set the vend price for a  
Warm Wash in Special Vend A.  
How to Program Special Vend A Reg.  
Warm Wash Vend Price  
NOTE: If the vend price is $100.00 or more, the  
fifth digit is “1”. If the vend price is $99.99 or less,  
the fifth digit is “0”.  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
C826I  
C826I  
Figure 76  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
fifth digit. Refer to Figure 77.  
C762I  
Figure 74  
NOTE: The vend price can be set from 0 to 65,535.  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+018” appears in the VFD. Refer  
to Figure 75.  
1
94
C794I  
3
2
C860I  
Figure 75  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
Figure 77  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Programming NetMaster  
6. Press the START (enter) keypad to enter the fifth  
digit and display remaining four digits. The  
active digit will flash one second on and one  
second off. Refer to Figure 78.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C88
C828I  
Figure 78  
7. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
active digit and the START (enter) keypad to  
enter the value of the digit and advance to the  
next digit.  
8. Press the START (enter) keypad with the last  
active digit. The next option, “+019”, will appear  
in the VFD.  
NOTE: To program “+019” (Special Vend A Reg.  
Cold Wash Vend Price), refer to option 19. To  
program other options, refer to the appropriate  
section.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
56  
 
Programming NetMaster  
4. When “+019” appears in the VFD, press the  
START (enter) keypad. There are five digits in  
the Special Vend A Reg. Cold Wash Vend Price.  
The fifth digit will appear in the VFD and will  
flash one second on and one second off. Refer to  
Figure 81.  
19. Special Vend A Reg. Cold Wash  
Vend Price “+019”  
This option allows the owner to set the vend price for a  
Cold Wash in Special Vend A.  
How to Program Special Vend A Reg. Cold  
Wash Vend Price  
NOTE: If the vend price is $100.00 or more, the  
fifth digit is “1”. If the vend price is $99.99 or less,  
the fifth digit is “0”.  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
C826I  
C826I  
Figure 81  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
fifth digit. Refer to Figure 82.  
C762I  
Figure 79  
NOTE: The vend price can be set from 0 to 65,535.  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+019” appears in the VFD. Refer  
to Figure 80.  
1
C793I  
3
2
C860I  
Figure 80  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
Figure 82  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Programming NetMaster  
6. Press the START (enter) keypad to enter the fifth  
digit and display remaining four digits. The  
active digit will flash one second on and one  
second off. Refer to Figure 83.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C88
C828I  
Figure 83  
7. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
active digit and the START keypad to enter the  
value of the digit and advance to the next digit.  
8. Press the START (enter) keypad with the last  
active digit. The next option, “+020”, will appear  
in the VFD.  
NOTE: To program “+020” (Special Vend A  
Auto-Shutdown Enable), refer to option 20. To  
program other options, refer to the appropriate  
section.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
58  
 
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current value  
displayed in the VFD to the desired value. Refer  
to Figure 86.  
20. Special Vend A Auto-Shutdown  
Enable “+020”  
This option, when turned on, will force the control to  
shutdown during the Programmed Special Vend A  
time period, preventing customers from starting a new  
cycle after a selected time. “OFF” is displayed on the  
VFD when Auto-Shutdown is active.  
1
How to Program Special Vend A Auto-  
Shutdown Enable  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
Figure 86  
6. Press the START (enter) keypad when the  
correct value appears in the VFD. The next option,  
“+021”, will appear in the VFD.  
C762I  
Figure 84  
NOTE: To program “+021” (Coin #1 Value), refer  
to option 21. To program other options, refer to the  
appropriate section.  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+020” appears in the VFD. Refer  
to Figure 85.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C792I  
Figure 85  
4. When “+020” appears in the VFD, press the  
START (enter) keypad. The current Special  
Vend A Auto-Shutdown Enable parameter value  
will appear in the VFD. “0” will be displayed  
when Auto-Shutdown is disabled and “255” will  
be displayed when Auto-Shutdown is enabled.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
59  
     
Programming NetMaster  
4. When “+021” appears in the VFD, press the  
START (enter) keypad.There are five digits in  
the Coin #1 Value. The fifth digit will appear in  
the VFD and will flash one second on and one  
second off. Refer to Figure 89.  
21. Coin #1 Value “+021”  
This option allows the owner to set a specific  
numerical value for a coin entered. For example, in the  
United States the coin value for one quarter would be  
measured in cents (25). Therefore, the coin value  
entered for one quarter would be 00025.  
NOTE: If the coin value is $100.00 or more, the  
fifth digit is “1”. If the coin value is $99.99 or less,  
the fifth digit is “0”.  
If the Reg. Hot Wash Vend Price (option 2) is set for  
“.75”, and the Coin Value is set for “00025”, the vend  
price displayed will decrease by .25 for each coin  
entered.  
How to Program Coin #1 Value  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
C826I  
C826I  
Figure 89  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
fifth digit. Refer to Figure 90.  
NOTE: The coin value can be set from 1 to 65,535.  
1
C762I  
Figure 87  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+021” appears in the VFD. Refer  
to Figure 88.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
91
C791I  
Figure 90  
Figure 88  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Programming NetMaster  
6. Press the START (enter) keypad to enter the fifth  
digit and display remaining four digits. The  
active digit will flash one second on and one  
second off. Refer to Figure 91.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C89
C829I  
Figure 91  
7. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
active digit and the START (enter) keypad to  
enter the value of the digit and advance to the  
next digit.  
8. Press the START (enter) keypad with the last  
active digit. The next option, “+022”, will appear  
in the VFD.  
NOTE: To program “+022” (Coin #2 Value), refer  
to option 22. To program other options, refer to the  
appropriate section.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61  
 
Programming NetMaster  
4. When “+022” appears in the VFD, press the  
START (enter) keypad. There are five digits in  
the Coin #2 Value. The fifth digit will appear in  
the VFD and will flash one second on and one  
second off. Refer to Figure 94.  
22. Coin #2 Value “+022”  
This option allows the owner to set a specific  
numerical value for a coin entered when using the dual  
coin drop. For example, the coin value for a dollar  
coin would be measured in cents (1.00). Therefore, the  
coin value entered for one dollar coin would be 00100.  
NOTE: If the coin value is $100.00 or more, the  
fifth digit is “1”. If the coin value is $99.99 or less,  
the fifth digit is “0”.  
If the Reg. Hot Wash Vend Price (option 2) is set for  
“2.00”, and the Coin Value is set for “00100”, the  
vend price displayed will decrease by 1.00 for each  
dollar coin entered.  
How to Program Coin #2 Value  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
C826I  
C826I  
Figure 94  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
fifth digit. Refer to Figure 95.  
NOTE: The coin value can be set from 1 to 65,535.  
1
C762I  
Figure 92  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+022” appears in the VFD. Refer  
to Figure 93.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
C790I  
Figure 95  
Figure 93  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Programming NetMaster  
6. Press the START (enter) keypad to enter the fifth  
digit and display remaining four digits. The  
active digit will flash one second on and one  
second off. Refer to Figure 96.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C827I  
C827I  
Figure 96  
7. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
active digit and the START (enter) keypad to  
enter the value of the digit and advance to the  
next digit.  
8. Press the START (enter) keypad with the last  
active digit. The next option, “+023”, will appear  
in the VFD.  
NOTE: To program “+023” (Start Pulse Value),  
refer to option 23. To program other options, refer  
to the appropriate section.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
63  
 
Programming NetMaster  
4. When “+023” appears in the VFD, press the  
START (enter) keypad. There are five digits in  
the Start Pulse Value. The fifth digit will appear  
in the VFD and will flash one second on and one  
second off. Refer to Figure 99.  
23. Start Pulse Value “+023”  
This option allows the owner to program the value of  
the Start Pulse if used for multiple pulses with an  
after-market central card reader or pay system. Refer  
to option 55 for additional information.  
NOTE: If the Start Pulse Value is $100.00 or more,  
the fifth digit is “1”. If the Start Pulse Value is  
$99.99 or less, the fifth digit is “0”.  
How to Program Start Pulse Value  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
C826I  
C826I  
Figure 99  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
fifth digit. Refer to Figure 100.  
C762I  
NOTE: The Start Pulse Value can be set from 1 to  
65,535.  
Figure 97  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+023” appears in the VFD. Refer  
to Figure 98.  
1
C789I  
3
2
Figure 98  
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
Figure 100  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Programming NetMaster  
6. Press the START (enter) keypad to enter the fifth  
digit and display remaining four digits. The  
active digit will flash one second on and one  
second off. Refer to Figure 101.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C87
C827I  
Figure 101  
7. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
active digit and the START (enter) keypad to  
enter the value of the digit and advance to the  
next digit.  
8. Press the START (enter) keypad with the last  
active digit. The next option, “+024”, will appear  
in the VFD.  
NOTE: To program “+024” (Default  
Cycle/Temperature), refer to option 24. To  
program other options, refer to the appropriate  
section.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
65  
 
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current number  
to the desired number selected from Table 3 on  
the following page. Refer to Figure 104.  
24. Default Cycle/Temperature  
“+024”  
This option allows the owner to set the default cycle  
and temperature the machine will enter when in the  
ready mode. When programming the default cycle,  
refer to Table 3 on the following page.  
1
How to Program Default Cycle/Temperature  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
Figure 104  
C762I  
6. Press the START (enter) keypad when the  
correct number appears in the VFD. The next  
option, “+025”, will appear in the VFD.  
Figure 102  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+024” appears in the VFD. Refer  
to Figure 103.  
NOTE: To program “+025” (Power Fail Reset),  
refer to option 25. To program other options, refer  
to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C788I  
Figure 103  
4. When “+024” appears in the VFD, press the  
START (enter) keypad. A number will appear in  
the VFD. This number corresponds to the current  
default cycle value.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
66  
     
Programming NetMaster  
How to Read Table 3  
To determine the correct number required to program  
Default Cycle/Temperature, use the following table.  
The Default Value column contains the number  
required in step 5. The other columns correspond to  
individual options.  
column’s option is turned on or off when the Default  
Value is entered. Select the desired combination of  
options and enter the number found in the Default Value  
column.  
Each column of options contains a unique combination  
of the words “ON” and “OFF” that indicates if that  
“+024”  
Default  
Value  
Perm Press  
Cycle  
Delicate  
Cycle  
Normal Cycle  
Hot Wash  
Warm Wash  
Cold Wash  
9
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
ON  
ON  
ON  
OFF  
OFF  
ON  
OFF  
ON  
ON  
OFF  
OFF  
ON  
10  
12  
17  
18  
20  
33  
34  
36  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
ON  
OFF  
Table 3  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
number to the desired number selected from  
Table 4. Refer to Figure 107.  
25. Power Fail Reset “+025”  
This option allows the owner to set the amount of time  
NetMaster will store active cycle information in the  
event of a power failure. The default setting for Power  
Fail Reset is OFF. If Power Fail Reset is turned OFF,  
the cycle will be saved for up to six years.  
1
How to Program Power Fail Reset  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
C762I  
Figure 107  
Figure 105  
6. Press the START (enter) keypad when the  
correct number appears in the VFD. The next  
option, “+026”, will appear in the VFD.  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+025” appears in the VFD. Refer  
to Figure 106.  
NOTE: To program “+026” (Set Real-Time Clock  
Minutes), refer to option 26. To program other  
options, refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
87
C787I  
Figure 106  
4. When “+025” appears in the VFD, press the  
START (enter) keypad. A number will appear in  
the VFD. This number corresponds to the current  
Power Fail Reset setting.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
68  
     
Programming NetMaster  
How to Read Table 4  
Use this table to set the amount of time for Power Fail  
Reset.  
If 133 is entered, the current cycle will be saved for up  
to five minutes. If power is not restored within five  
minutes, the control will erase the cycle status. The  
minimum power failure time is five minutes. The  
maximum power fail reset time is 127 minutes.  
The table range begins at 0 and ends at 255. Numbers  
entered between 0 and 127 turn the option OFF. If a  
number in this range is entered, the current cycle status  
will be saved for up to six years. When power is  
restored, the cycle will begin where it was interrupted.  
“+025”  
NUMBER TO ENTER IN STEP 6  
POWER FAIL RESET TIME  
Turned OFF  
000 – 127  
Cycle will be saved for a minimum of 6 years  
133  
5 minutes without power before cycle is lost  
. . . add one minute for every number up to  
255  
127 minutes without power before cycle is lost  
Table 4  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the minutes to the  
correct time. Refer to Figure 110.  
26. Set Real-Time Clock Minutes  
“+026”  
This option allows the owner to set NetMaster’s  
internal clock to the correct time in minutes.  
1
How to Program the Clock Minutes  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
C762I  
Figure 110  
Figure 108  
6. Press the START (enter) keypad when the  
correct time in minutes appears in the VFD. The  
next option, “+027”, will appear in the VFD.  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+026” appears in the VFD. Refer  
to Figure 109.  
NOTE: To program “+027” (Set Real-Time Clock  
Hours), refer to option 27. To program other  
options, refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
76
C786I  
Figure 109  
4. When “+026” appears in the VFD, press the  
START (enter) keypad. The current time in  
minutes will appear in the VFD.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
70  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the hours to the  
correct time. Refer to Figure 113.  
27. Set Real-Time Clock Hours  
“+027”  
This option allows the owner to set NetMaster’s  
internal clock to the correct time in hours.  
1
How to Program the Clock Hours  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
C762I  
Figure 113  
Figure 111  
6. Press the START (enter) keypad when the  
correct time in hours appears in the VFD. The  
next option, “+028”, will appear in the VFD.  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+027” appears in the VFD. Refer  
to Figure 112.  
NOTE: To program “+028” (Set Real-Time Clock  
Day), refer to option 28. To program other options,  
refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C785I  
Figure 112  
4. When “+027” appears in the VFD, press the  
START (enter) keypad. The current time in hours  
will appear in the VFD.  
NOTE: The hours will be displayed in military time.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
71  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the day until  
correct. Refer to Figure 116.  
28. Set Real-Time Clock Day “+028”  
This option allows the owner to set NetMaster’s  
internal clock to the correct day of the week.  
NOTE: Sunday is considered day one (001),  
Monday is day two (002) and so on.  
How to Program the Clock Day  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
1
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
C762I  
Figure 114  
3
Press this pad (-) to scroll back or decrease a value  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+028” appears in the VFD. Refer  
to Figure 115.  
Figure 116  
6. Press the START (enter) keypad when the  
correct day appears in the VFD. The next option,  
“+029”, will appear in the VFD.  
NOTE: To program “+029” (Set Real-Time Clock  
Date), refer to option 29. To program other options,  
refer to the appropriate section.  
How to Exit Programming Feature  
C784I  
1. Be sure the control shows a programmable option,  
not a value.  
Figure 115  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
4. When “+028” appears in the VFD, press the  
START (enter) keypad. The current day of the  
week will appear in the VFD.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
72  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the day of the  
month until correct. Refer to Figure 119.  
29. Set Real-Time Clock Date  
“+029”  
This option allows the owner to set NetMaster’s  
internal clock to the correct day of the month.  
1
How to Program the Clock Date  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
C762I  
Figure 119  
Figure 117  
6. Press the START (enter) keypad when the  
correct day of the month appears in the VFD. The  
next option, “+030”, will appear in the VFD.  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+029” appears in the VFD. Refer  
to Figure 118.  
NOTE: To program “+030” (Set Real-Time Clock  
Month), refer to option 30. To program other  
options, refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
73
C783I  
Figure 118  
4. When “+029” appears in the VFD, press the  
START (enter) keypad. The current day of the  
month will appear in the VFD.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
73  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the month until  
correct. Refer to Figure 122.  
30. Set Real-Time Clock Month  
“+030”  
This option allows the owner to set NetMaster’s  
internal clock to the correct month.  
1
How to Program the Clock Month  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
C762I  
Figure 122  
Figure 120  
6. Press the START (enter) keypad when the  
correct month appears in the VFD. The next  
option, “+031”, will appear in the VFD.  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+030” appears in the VFD. Refer  
to Figure 121.  
NOTE: To program “+031” (Set Real-Time Clock  
Year), refer to option 31. To program other options,  
refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
72
C782I  
Figure 121  
4. When “+030” appears in the VFD, press the  
START (enter) keypad. The current month will  
appear in the VFD.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
74  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the year until  
correct. Refer to Figure 125.  
31. Set Real-Time Clock Year  
“+031”  
This option allows the owner to set NetMaster’s  
internal clock to the correct year.  
NOTE: The year 2000 is “00”, the year 2001 is “01”  
and so on.  
How to Program the Clock Year  
1. Control must be in Manual Mode. Refer to  
1
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
C762I  
3
Press this pad (-) to scroll back or decrease a value  
Figure 123  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+031” appears in the VFD. Refer  
to Figure 124.  
Figure 125  
6. Press the START (enter) keypad when the  
correct year appears in the VFD. The next option,  
“+032”, will appear in the VFD.  
NOTE: To program “+032” (Set Real-Time Clock  
Century), refer to option 32. To program other  
options, refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
71
C781I  
Figure 124  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
4. When “+031” appears in the VFD, press the  
START (enter) keypad. The current year will  
appear in the VFD.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
75  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the century until  
correct. Refer to Figure 128.  
32. Set Real-Time Clock Century  
“+032”  
This option allows the owner to set NetMaster’s  
internal clock to the correct century.  
NOTE: The digits “20” are used for century.  
How to Program the Clock Century  
1
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
C762I  
3
Press this pad (-) to scroll back or decrease a value  
Figure 126  
Figure 128  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+032” appears in the VFD. Refer  
to Figure 127.  
6. Press the START (enter) keypad when the  
correct century appears in the VFD. The next  
option, “+033”, will appear in the VFD.  
NOTE: To program “+033” (Normal Wash  
Agitate Time), refer to option 33. To program other  
options, refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
70
C780I  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
Figure 127  
4. When “+032” appears in the VFD, press the  
START (enter) keypad. The current century will  
appear in the VFD.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
76  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
33. Normal Wash Agitate Time  
“+033”  
number of minutes displayed in the VFD to the  
desired number of minutes. Refer to Figure 131.  
This option allows the owner to set the amount of  
wash agitate time for the Normal cycle.  
NOTE: The Normal Wash Agitate Time can be set  
from zero (0) to 15 minutes.  
How to Program Normal Wash Agitate  
Time  
1
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
C762I  
3
Press this pad (-) to scroll back or decrease a value  
Figure 129  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+033” appears in the VFD. Refer  
to Figure 130.  
Figure 131  
6. Press the START (enter) keypad when the  
correct number of minutes appears in the VFD.  
The next option, “+034”, will appear in the VFD.  
NOTE: To program “+034” (Normal Extra Rinse  
Agitate Time), refer to option 34. To program other  
options, refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
79
C779I  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
Figure 130  
4. When “+033” appears in the VFD, press the  
START (enter) keypad. The current number of  
minutes set for the Normal Wash Agitate Time  
will appear in the VFD.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
77  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
34. Normal Extra Rinse Agitate  
Time “+034”  
number of minutes displayed in the VFD to the  
desired number of minutes. Refer to Figure 134.  
This option allows the owner to set the amount of  
extra rinse agitate time for the Normal cycle.  
NOTE: The Normal Extra Rinse Agitate Time can  
be set from zero (0) to 15 minutes.  
How to Program Normal Extra Rinse  
Agitate Time  
1
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
C762I  
3
Press this pad (-) to scroll back or decrease a value  
Figure 132  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+034” appears in the VFD. Refer  
to Figure 133.  
Figure 134  
6. Press the START (enter) keypad when the  
correct number of minutes appears in the VFD.  
The next option, “+035”, will appear in the VFD.  
NOTE: To program “+035” (Normal Rinse Agitate  
Time), refer to option 35. To program other  
options, refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
C778I  
C778I  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
Figure 133  
4. When “+034” appears in the VFD, press the  
START (enter) keypad. The current number of  
minutes set for the Normal Extra Rinse Agitate  
Time will appear in the VFD.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
78  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
35. Normal Rinse Agitate Time  
“+035”  
number of minutes displayed in the VFD to the  
desired number of minutes. Refer to Figure 137.  
This option allows the owner to set the amount of time  
for a rinse agitate in the Normal cycle.  
NOTE: The Normal Rinse Agitate Time can be set  
from zero (0) to 15 minutes.  
How to Program Normal Rinse Agitate  
Time  
1
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
C762I  
3
Press this pad (-) to scroll back or decrease a value  
Figure 135  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+035” appears in the VFD. Refer  
to Figure 136.  
Figure 137  
6. Press the START (enter) keypad when the  
correct number of minutes appears in the VFD.  
The next option, “+036”, will appear in the VFD.  
NOTE: To program “+036” (Normal Final Spin  
Time), refer to option 36. To program other  
options, refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
C796I  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
Figure 136  
4. When “+035” appears in the VFD, press the  
START (enter) keypad. The current number of  
minutes set for the Normal Rinse Agitate Time  
will appear in the VFD.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
79  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
36. Normal Final Spin Time “+036”  
This option allows the owner to set the amount of time  
for a final spin in the Normal cycle.  
number of minutes displayed in the VFD to the  
desired number of minutes. Refer to Figure 140.  
How to Program Normal Final Spin Time  
NOTE: The Normal Final Spin Time can be set  
from zero (0) to 15 minutes.  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
1
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
C762I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
Figure 138  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+036” appears in the VFD. Refer  
to Figure 139.  
3
Press this pad (-) to scroll back or decrease a value  
Figure 140  
6. Press the START (enter) keypad when the  
correct number of minutes appears in the VFD.  
The next option, “+037”, will appear in the VFD.  
NOTE: To program “+037” (Permanent Press  
Wash Agitate Time), refer to option 37. To program  
other options, refer to the appropriate section.  
77
C797I  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
Figure 139  
4. When “+036” appears in the VFD, press the  
START (enter) keypad. The current number of  
minutes set for the Normal Final Spin Time will  
appear in the VFD.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
80  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
37. Permanent Press Wash Agitate  
Time “+037”  
number of minutes displayed in the VFD to the  
desired number of minutes. Refer to Figure 143.  
This option allows the owner to set the amount of  
wash agitate time for the Permanent Press cycle.  
NOTE: The Permanent Press Wash Agitate Time  
can be set from zero (0) to 15 minutes.  
How to Program Permanent Press Wash  
Agitate Time  
1
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
C762I  
3
Press this pad (-) to scroll back or decrease a value  
Figure 141  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+037” appears in the VFD. Refer  
to Figure 142.  
Figure 143  
6. Press the START (enter) keypad when the  
correct number of minutes appears in the VFD.  
The next option, “+038”, will appear in the VFD.  
NOTE: To program “+038” (Permanent Press  
Extra Rinse Agitate Time), refer to option 38. To  
program other options, refer to the appropriate  
section.  
How to Exit Programming Feature  
78
C798I  
1. Be sure the control shows a programmable option,  
not a value.  
Figure 142  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
4. When “+037” appears in the VFD, press the  
START (enter) keypad. The current number of  
minutes set for the Permanent Press Wash  
Agitate Time will appear in the VFD.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
81  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
38. Permanent Press Extra Rinse  
Agitate Time “+038”  
number of minutes displayed in the VFD to the  
desired number of minutes. Refer to Figure 146.  
This option allows the owner to set the amount of  
extra rinse agitate time for the Permanent Press cycle.  
NOTE: The Permanent Press Extra Rinse Agitate  
Time can be set from zero (0) to 15 minutes.  
How to Program Permanent Press Extra  
Rinse Agitate Time  
1
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
C762I  
3
Press this pad (-) to scroll back or decrease a value  
Figure 144  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+038” appears in the VFD. Refer  
to Figure 145.  
Figure 146  
6. Press the START (enter) keypad when the  
correct number of minutes appears in the VFD.  
The next option, “+039”, will appear in the VFD.  
NOTE: To program “+039” (Permanent Press  
Rinse Agitate Time), refer to option 39. To program  
other options, refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
79
C799I  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
Figure 145  
4. When “+038” appears in the VFD, press the  
START (enter) keypad. The current number of  
minutes set for the Permanent Press Extra Rinse  
Agitate Time will appear in the VFD.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
82  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
39. Permanent Press Rinse Agitate  
Time “+039”  
number of minutes displayed in the VFD to the  
desired number of minutes. Refer to Figure 149.  
This option allows the owner to set the amount of rinse  
agitate time for the Permanent Press cycle.  
NOTE: The Permanent Press Rinse Agitate Time  
can be set from zero (0) to 15 minutes.  
How to Program Permanent Press Rinse  
Agitate Time  
1
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
C762I  
3
Press this pad (-) to scroll back or decrease a value  
Figure 147  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+039” appears in the VFD. Refer  
to Figure 148.  
Figure 149  
6. Press the START (enter) keypad when the  
correct number of minutes appears in the VFD.  
The next option, “+040”, will appear in the VFD.  
NOTE: To program “+040” (Permanent Press  
Final Spin Time), refer to option 40. To program  
other options, refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
C800I  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
Figure 148  
4. When “+039” appears in the VFD, press the  
START (enter) keypad. The current number of  
minutes set for the Permanent Press Rinse  
Agitate Time will appear in the VFD.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
83  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
40. Permanent Press Final Spin  
Time “+040”  
number of minutes displayed in the VFD to the  
desired number of minutes. Refer to Figure 152.  
This option allows the owner to set the amount of final  
spin time for the Permanent Press cycle.  
NOTE: The Permanent Press Final Spin Time can  
be set from zero (0) to 15 minutes.  
How to Program Permanent Press Final  
Spin Time  
1
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
C762I  
3
Press this pad (-) to scroll back or decrease a value  
Figure 150  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+040” appears in the VFD. Refer  
to Figure 151.  
Figure 152  
6. Press the START (enter) keypad when the  
correct number of minutes appears in the VFD.  
The next option, “+041”, will appear in the VFD.  
NOTE: To program “+041” (Delicate Wash  
Agitate Time), refer to option 41. To program other  
options, refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
C801I  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
Figure 151  
4. When “+040” appears in the VFD, press the  
START (enter) keypad. The current number of  
minutes set for the Permanent Press Final Spin  
Time will appear in the VFD.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
84  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
41. Delicate Wash Agitate Time  
“+041”  
number of minutes displayed in the VFD to the  
desired number of minutes. Refer to Figure 155.  
This option allows the owner to set the amount of  
wash agitate time for the Delicate cycle.  
NOTE: The Delicate Wash Agitate Time can be set  
from zero (0) to 15 minutes.  
How to Program Delicate Wash Agitate  
Time  
1
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
C762I  
3
Press this pad (-) to scroll back or decrease a value  
Figure 153  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+041” appears in the VFD. Refer  
to Figure 154.  
Figure 155  
6. Press the START (enter) keypad when the  
correct number of minutes appears in the VFD.  
The next option, “+042”, will appear in the VFD.  
NOTE: To program “+042” (Delicate Extra Rinse  
Agitate Time), refer to option 42. To program other  
options, refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
C802I  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
Figure 154  
4. When “+041” appears in the VFD, press the  
START (enter) keypad. The current number of  
minutes set for the Delicate Wash Agitate Time  
will appear in the VFD.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
85  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
42. Delicate Extra Rinse Agitate  
Time “+042”  
number of minutes displayed in the VFD to the  
desired number of minutes. Refer to Figure 158.  
This option allows the owner to set the amount of  
extra rinse agitate time for the Delicate cycle.  
NOTE: The Delicate Extra Rinse Agitate Time can  
be set from zero (0) to 15 minutes.  
How to Program Delicate Extra Rinse  
Agitate Time  
1
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
C762I  
3
Press this pad (-) to scroll back or decrease a value  
Figure 156  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+042” appears in the VFD. Refer  
to Figure 157.  
Figure 158  
6. Press the START (enter) keypad when the  
correct number of minutes appears in the VFD.  
The next option, “+043”, will appear in the VFD.  
NOTE: To program “+043” (Delicate Rinse  
Agitate Time), refer to option 43. To program other  
options, refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
C803I  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
Figure 157  
4. When “+042” appears in the VFD, press the  
START (enter) keypad. The current number of  
minutes set for the Delicate Extra Rinse Agitate  
Time will appear in the VFD.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
86  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
43. Delicate Rinse Agitate Time  
“+043”  
number of minutes displayed in the VFD to the  
desired number of minutes. Refer to Figure 161.  
This option allows the owner to set the amount of rinse  
agitate time for the Delicate cycle.  
NOTE: The Delicate Rinse Agitate Time can be set  
from zero (0) to 15 minutes.  
How to Program Delicate Rinse Agitate  
Time  
1
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
C762I  
3
Press this pad (-) to scroll back or decrease a value  
Figure 159  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+043” appears in the VFD. Refer  
to Figure 160.  
Figure 161  
6. Press the START (enter) keypad when the  
correct number of minutes appears in the VFD.  
The next option, “+044”, will appear in the VFD.  
NOTE: To program “+044” (Delicate Final Spin  
Time), refer to option 44. To program other  
options, refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
C804I  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
Figure 160  
4. When “+043” appears in the VFD, press the  
START (enter) keypad. The current number of  
minutes set for the Delicate Rinse Agitate time  
will appear in the VFD.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
87  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
44. Delicate Final Spin Time “+044”  
This option allows the owner to set the amount of final  
spin time for the Delicate cycle.  
number of minutes displayed in the VFD to the  
desired number of minutes. Refer to Figure 164.  
How to Program Delicate Final Spin Time  
NOTE: The Delicate Final Spin Time can be set  
from zero (0) to 15 minutes.  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
1
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
C762I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
Figure 162  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+044” appears in the VFD. Refer  
to Figure 163.  
3
Press this pad (-) to scroll back or decrease a value  
Figure 164  
6. Press the START (enter) keypad when the  
correct number of minutes appears in the VFD.  
The next option, “+045”, will appear in the VFD.  
NOTE: To program “+045” (Warm Rinse Enable/  
Disable), refer to option 45. To program other  
options, refer to the appropriate section.  
How to Exit Programming Feature  
C805I  
1. Be sure the control shows a programmable option,  
not a value.  
Figure 163  
4. When “+044” appears in the VFD, press the  
START (enter) keypad. The current number of  
minutes set for the Delicate Final Spin Time will  
appear in the VFD.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
88  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-) keypad  
to increase or decrease the current number to the  
desired number. Refer to Figure 167.  
45. Warm Rinse Enable/Disable  
“+045”  
This option allows the owner to program an optional  
warm fill temperature for the final rinse fill. If this  
option is enabled and HOT or WARM water is  
selected for the wash fill, warm water will be used for  
the final rinse fill.  
1
How to Program the Warm Rinse Enable/  
Disable  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
Figure 167  
6. Press the START (enter) keypad when the  
correct number appears in the VFD. The next  
option, “+046”, will appear in the VFD.  
C762I  
Figure 165  
NOTE: To program “+046” (Control Configuration  
Data #1), refer to option 46. To program other  
options, refer to the appropriate section.  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+045” appears in the VFD. Refer  
to Figure 166.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C806I  
Figure 166  
4. When “+045” appears in the VFD, press the  
START (enter) keypad. A number will appear in  
the VFD. This number (found below) corresponds  
to the current Warm Rinse Enable/Disable Value.  
One (1) = Option Enabled  
Zero (0) = Option Disabled  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
89  
     
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
number to the desired number selected from  
Table 5. Refer to Figure 170.  
46. Control Configuration Data #1  
“+046”  
This option allows the owner to turn ON or turn OFF  
preprogrammed capabilities within NetMaster.  
1
How to Program the Control Configuration  
Data #1  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
C762I  
Figure 170  
Figure 168  
6. Press the START (enter) keypad when the  
correct number appears in the VFD. The next  
option, “+047”, will appear in the VFD.  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+046” appears in the VFD. Refer  
to Figure 169.  
NOTE: To program “+047” (Control Configuration  
Data #3), refer to option 47. To program other  
options, refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C807I  
Figure 169  
4. When “+046” appears in the VFD, press the  
START (enter) keypad. A number will appear in  
the VFD. This number corresponds to the current  
Control Configuration Data #1 Value.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
90  
     
Programming NetMaster  
Configuration #1 Programming  
Use the table on the following page (Table 5) to turn  
on or turn off the preprogrammed daylight savings  
option, wash temperature display option, infra-red  
access option, decimal point option, EC Power Fail,  
and the automatic collect option in NetMaster.  
To change any or all of these configuration options,  
review the following descriptions carefully and choose  
the appropriate configuration value from Table 5.  
Enter the appropriate value in step 5 on the previous  
page.  
Daylight Savings  
This option automatically sets the clock in NetMaster to account for the time change during  
Daylight Savings.  
OFF= Turns off the automatic daylight savings option programmed in NetMaster.  
ON = Turns on the automatic daylight savings option programmed in NetMaster.  
Wash Temperature  
This option determines if the temperature LEDs indicate the selected wash temperature during the  
entire cycle or indicates fill temperature during each rinse.  
OFF= Selected wash temperature remains on for entire cycle.  
ON = LEDs indicate actual water temperature during every fill step. LEDs will be off during steps  
when water is not filling in the wash drum.  
Infra-red Access  
Decimal Point  
This option determines if a Micro-Wand can access or program NetMaster.  
OFF= Turns off the infra-red access by the Micro-Wand.  
ON = Turns on the infra-red access by the Micro-Wand.  
This option determines if a decimal point is used when displaying the vend price (i.e. machines  
using token currency may choose to remove the decimal point).  
OFF= Turns off the decimal point from appearing in the VFD.  
ON = Turns on the decimal point to appear in the VFD.  
Automatic Collect  
EC Power Fail  
This option automatically collects all audit data information whenever the Micro-Wand  
communicates with the control.  
OFF= Turns off the automatic collect with the Micro-Wand.  
ON = Turns on the automatic collect with the Micro-Wand.  
This option determines if the European Community Power Fail feature is enabled. If enabled and a  
power failure lasts at least two seconds, the control will require the user to press the START pad to  
resume the cycle that was in operation at the time of the power failure.  
OFF= Turns off the European Community Power Fail feature.  
ON = Turns on the European Community Power Fail feature.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
91  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programming NetMaster  
“+046”  
Config #1  
Value  
EC Power  
Auto  
Decimal  
Point  
Infra-red  
Access  
Wash Temp  
Indicate  
Daylight  
Savings  
Fail  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
Collect  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
48  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
144  
145  
146  
147  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
ON  
OFF  
ON  
ON  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
OFF  
ON  
ON  
ON  
Table 5  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
92  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Programming NetMaster  
“+046” (continued)  
Config #1  
Value  
EC Power  
Fail  
Auto  
Decimal  
Point  
Infra-red  
Access  
Wash Temp  
Daylight  
Savings  
Collect  
Indicate  
OFF  
OFF  
ON  
148  
149  
150  
151  
152  
153  
154  
155  
156  
157  
158  
159  
176  
177  
178  
179  
180  
181  
182  
183  
184  
185  
186  
187  
188  
189  
190  
191  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
OFF  
ON  
OFF  
ON  
ON  
OFF  
OFF  
ON  
OFF  
ON  
OFF  
ON  
ON  
OFF  
OFF  
ON  
OFF  
ON  
OFF  
ON  
ON  
OFF  
OFF  
ON  
OFF  
ON  
OFF  
ON  
ON  
OFF  
OFF  
ON  
OFF  
ON  
OFF  
ON  
ON  
OFF  
OFF  
ON  
OFF  
ON  
OFF  
ON  
ON  
OFF  
OFF  
ON  
OFF  
ON  
OFF  
ON  
ON  
Table 5  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
93  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
number to the desired number selected from  
Table 6. Refer to Figure 173.  
47. Control Configuration Data #3  
“+047”  
This option allows the owner to turn ON or turn OFF  
preprogrammed capabilities within NetMaster.  
1
How to Program the Control Configuration  
Data #3  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
C762I  
Figure 173  
Figure 171  
6. Press the START (enter) keypad when the  
correct number appears in the VFD. The next  
option, “+048”, will appear in the VFD.  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+047” appears in the VFD. Refer  
to Figure 172.  
NOTE: To program “+048” (Lucky Option), refer  
to option 48. To program other options, refer to the  
appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C808I  
c808i  
Figure 172  
4. When “+047” appears in the VFD, press the  
START (enter) keypad. A number will appear in  
the VFD. This number corresponds to the current  
Control Configuration Data #3 Value.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
94  
     
Programming NetMaster  
NOTE: Selecting “Ready Mode” for the available  
output will turn off the available output after the  
first pulse is received. Selecting “Until Start Mode”  
will keep the available output on until the vend  
price is satisfied. This feature is used for  
Configuration #3 Programming  
Use the table below (Table 6) to turn on or turn off  
access for Manual Rapid Advance and Diagnostics,  
and to change the Available Output Mode.  
aftermarket card read or central pay systems.  
“+047”  
RADV/DIAG Access  
Config #3 Value  
Available  
Ready Mode  
0
1
2
3
OFF  
OFF  
ON  
Until Start Mode  
Ready Mode  
ON  
Until Start Mode  
Table 6  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
95  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Programming NetMaster  
the VFD. This number corresponds to the current  
Lucky Option Programming Value.  
48. Lucky Option “+048”  
This option allows the owner to program the machine  
to provide a free vend cycle to customers after a  
certain number of machine cycles have occurred.  
5. Locate the desired number in the first column of  
Table 7 below.  
For coin models, “FrEE” will be displayed five  
minutes after the completion of the programmed  
number of cycles has occurred. The cycle can then be  
started by pressing the START (enter) pad.  
“+048”  
Lucky Option  
Value  
Lucky Cycle  
ON/OFF  
Number of  
Cycles  
1 – 127  
129  
OFF  
ON  
ON  
ON  
1 – 127  
For card models, when a card is inserted, the VFD will  
display “bAL” followed by the card balance. When the  
user presses the START pad, a zero vend will be  
deducted from the card. The VFD will display  
“WAIT”. The VFD will then display “FrEE” for five  
seconds and then the cycle time will be displayed.  
When the card is removed, the VFD will flash the  
remaining balance for three seconds and will then revert  
back to the cycle time.  
1
2
130  
131 – 255  
3 – 127  
Table 7  
6. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
number until correct. Refer to Figure 176.  
How to Program Lucky Option  
1
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
C762I  
Figure 174  
Figure 176  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+048” appears in the VFD. Refer  
to Figure 175.  
7. Press the START (enter) keypad when the  
correct number appears in the VFD. The next  
option, “+049”, will appear in the VFD.  
NOTE: To program “+049” (Special Cycle  
Option), refer to option 49. To program other  
options, refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
C809I  
C809I  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
Figure 175  
4. When “+048” appears in the VFD, press the  
START (enter) keypad. A number will appear in  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
96  
       
Programming NetMaster  
5. Locate the desired number in the first column of  
49. Special Cycle Option “+049”  
Table 8 on the following page.  
This option allows the owner to program the machine  
to offer extra wash time, extra rinse time, warm rinse,  
or any combination of the above to the customers for  
an added vend price.  
6. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
number until correct. Refer to Figure 179.  
How to Program Special Cycle Option  
1
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
C762I  
3
Press this pad (-) to scroll back or decrease a value  
Figure 177  
Figure 179  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+049” appears in the VFD. Refer  
to Figure 178.  
7. Press the START (enter) keypad when the  
correct number appears in the VFD. The next  
option, “+050”, will appear in the VFD.  
NOTE: To program “+050” (Special Cycle Extra  
Wash Time), refer to option 50. To program other  
options, refer to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
C810I  
C812I  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
Figure 178  
4. When “+049” appears in the VFD, press the  
START (enter) keypad. A number will appear in  
the VFD. This number corresponds to the current  
Special Cycle Option Programming Value.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
97  
     
Programming NetMaster  
How to Read Table 8  
To determine the correct number required to program  
Special Cycle Option, use the following table. The  
Special Cycle Option Value column contains the  
number required in step 6. The other columns  
correspond to individual options.  
Each column of options contains a unique combination  
of the words “ON” and “OFF” that indicates if that  
column’s option is turned on or off when the Special  
Cycle Option Value is entered. Select the desired  
combination of options and enter the number found in  
the Special Cycle Option Value column.  
“+049”  
Special Cycle  
Option Value  
Special Cycle  
ON/OFF  
Warm Rinse ON/OFF  
0
OFF  
ON  
ON  
OFF  
OFF  
ON  
128  
129  
Table 8  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
98  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
50. Special Cycle Extra Wash Time  
“+050”  
number of minutes displayed in the VFD to the  
desired number of minutes. Refer to Figure 182.  
This option allows the owner to set the amount of  
additional wash time for the Special Cycle.  
NOTE: The Special Cycle Extra Wash Time can be  
set from zero (0) to 15 minutes.  
How to Program Special Cycle Extra  
Wash Time  
1
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
C762I  
3
Press this pad (-) to scroll back or decrease a value  
Figure 180  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+050” appears in the VFD. Refer  
to Figure 181.  
Figure 182  
6. Press the START (enter) keypad when the  
correct number of minutes appears in the VFD.  
The next option, “+051”, will appear in the VFD.  
NOTE: The Special Cycle option needs to be  
turned on (refer to option 49) for the Special Cycle  
Extra Wash Time to take effect.  
NOTE: To program “+051” (Special Cycle Extra  
Extra-Rinse Time), refer to option 51. To program  
other options, refer to the appropriate section.  
C811I  
C811I  
How to Exit Programming Feature  
Figure 181  
1. Be sure the control shows a programmable option,  
not a value.  
4. When “+050” appears in the VFD, press the  
START (enter) keypad. The current number of  
minutes set for the Special Cycle Extra Wash  
Time will appear in the VFD.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
99  
   
Programming NetMaster  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
51. Special Cycle Extra Extra-Rinse  
Time “+051”  
number of minutes displayed in the VFD to the  
desired number of minutes. Refer to Figure 185.  
This option allows the owner to set the amount of  
additional extra rinse time for the Special Cycle.  
NOTE: The Special Cycle Extra Extra-Rinse Time  
can be set from zero (0) to 15 minutes.  
How to Program Special Cycle Extra  
Extra-Rinse Time  
1
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
C762I  
3
Press this pad (-) to scroll back or decrease a value  
Figure 183  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+051” appears in the VFD. Refer  
to Figure 184.  
Figure 185  
6. Press the START (enter) keypad when the  
correct number of minutes appears in the VFD.  
The next option, “+052”, will appear in the VFD.  
NOTE: The Special Cycle option needs to be  
turned on (refer to option 49) for the Special Cycle  
Extra Extra-Rinse Time to take effect.  
NOTE: To program “+052” (Smart Card  
Maximum Value), refer to option 52. To program  
other options, refer to the appropriate section.  
C812I  
C812I  
How to Exit Programming Feature  
Figure 184  
1. Be sure the control shows a programmable option,  
not a value.  
4. When “+051” appears in the VFD, press the  
START (enter) keypad. The current number of  
minutes set for the Special Cycle Extra Extra-  
Rinse Time will appear in the VFD.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
100  
     
Programming NetMaster  
4. When “+052” appears in the VFD, press the  
START (enter) keypad. There are five digits in  
the Smart Card Maximum Value. The fifth digit  
will appear in the VFD and will flash one second  
on, one second off. Refer to Figure 188.  
52. Smart Card Maximum Value  
“+052”  
This option allows the owner to set the maximum card  
balance that will be accepted. If a cash value card is  
inserted with a balance greater than this value, it will  
not be accepted.  
NOTE: If the Smart Card Maximum Value is  
$100.00 or more, the fifth digit is “1”. If the Smart  
Card Maximum Value is $99.99 or less, the fifth  
digit is “0”.  
How to Program Smart Card Maximum  
Value  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
C826I  
C826I  
Figure 188  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
fifth digit. Refer to Figure 189.  
C762I  
1
Figure 186  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+052” appears in the VFD. Refer  
to Figure 187.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
C813I  
C813I  
3
Press this pad (-) to scroll back or decrease a value  
Figure 187  
Figure 189  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
101  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Programming NetMaster  
6. Press the START (enter) keypad to enter the fifth  
digit and display remaining four digits. The  
active digit will flash one second on and one  
second off. Refer to Figure 190.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C87
C827I  
Figure 190  
7. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
active digit and the START (enter) keypad to  
enter the value of the digit and advance to the  
next digit.  
8. Press the START (enter) keypad with the last  
active digit. The next option, “+053”, will appear  
in the VFD.  
NOTE: To program “+053” (Site Code #1), refer to  
option 53. To program other options, refer to the  
appropriate section.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
102  
 
Programming NetMaster  
4. When “+053” appears in the VFD, press the  
START (enter) keypad. There are five digits in  
Site Code #1. The fifth digit will appear in the  
VFD and will flash one second on, one second  
off. Refer to Figure 193.  
53. Site Code #1 “+053”  
This option allows the owner to program a site code to  
correspond with the Site Code #1 pricing. This allows  
different pricing for a specific site code.  
How to Program Site Code #1  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
C826I  
C826I  
Figure 193  
5. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
fifth digit. Refer to Figure 194.  
1
C762I  
Figure 191  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+053” appears in the VFD. Refer  
to Figure 192.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
C840I  
C840I  
3
Press this pad (-) to scroll back or decrease a value  
Figure 192  
Figure 194  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
103  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Programming NetMaster  
6. Press the START (enter) keypad to enter the fifth  
digit and display remaining four digits. The  
active digit will flash one second on and one  
second off. Refer to Figure 195.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C868I  
Figure 195  
7. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the value of the  
active digit and the START (enter) keypad to  
enter the value of the digit and advance to the  
next digit.  
8. Press the START (enter) keypad with the last  
active digit. The next option, “+054”, will appear  
in the VFD.  
NOTE: To program “+054” (Error Code  
Programming Parameter), refer to option 54. To  
program other options, refer to the appropriate  
section.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
104  
 
Programming NetMaster  
6. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
number until correct. Refer to Figure 198.  
54. Error Code Programming  
Parameter “+054”  
This option allows the owner to turn on or turn off  
certain errors in the control.  
1
How to Program Error Code Programming  
Parameter  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
Figure 198  
C762I  
7. Press the START (enter) keypad when the  
correct number appears in the VFD. The next  
option, “+055”, will appear in the VFD.  
Figure 196  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+054” appears in the VFD. Refer  
to Figure 197.  
NOTE: To program “+055” (Start Pulse Mode),  
refer to option 55. To program other options, refer  
to the appropriate section.  
How to Exit Programming Feature  
1. Be sure the control shows a programmable option,  
not a value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
C815I  
C815I  
Figure 197  
4. When “+054” appears in the VFD, press the  
START (enter) keypad. A number will appear in  
the VFD. This number corresponds to the current  
Error Code Programming Parameter Value.  
5. Locate the desired number in the first column of  
Table 9 on the following page.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
105  
     
Programming NetMaster  
How to Read Table 9  
To determine the correct number required to program  
Error Code Programming Parameter, use the following  
table. The Error Code Value column contains the  
number required in step 6. The other columns  
correspond to individual options.  
Each column of options contains a unique combination  
of the words “ON” and “OFF” that indicates if that  
column’s option is turned on or off when the Error  
Code Value is entered. Select the desired combination  
of options and enter the number found in the Error  
Code Value column.  
“+054”  
Error Code Value  
Drain Error  
OFF  
Fill Error  
OFF  
OFF  
ON  
Coin Error  
OFF  
0
1
OFF  
ON  
4
OFF  
OFF  
5
OFF  
ON  
ON  
8
ON  
OFF  
OFF  
ON  
OFF  
9
ON  
ON  
12  
13  
ON  
OFF  
ON  
ON  
ON  
Table 9  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
106  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Programming NetMaster  
5. Locate the desired number in the first column of  
55. Start Pulse Mode “+055”  
Table 10 below.  
This option allows the owner to program the Start  
Pulse Input. The Start Pulse Mode can be used for  
after-market central pay or card systems. The central  
system sends the start pulse to the Start Pulse Input of  
the control to start the cycle. If set for single pulse, one  
start pulse from the central system will start the cycle.  
If set for multiple pulses, each pulse will deduct from  
the vend price the value set up in option 23 (Start  
Pulse Value) until the vend is satisfied.  
“+055”  
Start Pulse  
Mode Value  
Start Pulse  
ON/OFF  
Single Pulse/  
Multiple Pulses  
0
OFF  
OFF  
ON  
Single Pulse  
Multiple Pulses  
Single Pulse  
64  
128  
192  
ON  
Multiple Pulses  
How to Program Start Pulse Mode  
Table 10  
1. Control must be in Manual Mode. Refer to  
6. Press the DELICATES (+) or the COLD (-)  
keypad to increase or decrease the current  
number until correct. Refer to Figure 201.  
Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “PrOg” appears in the VFD. Press  
the START (enter) keypad and “+001” will  
appear in the VFD.  
1
C762I  
Figure 199  
3
2
C860I  
3. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the programmable  
options until “+055” appears in the VFD. Refer  
to Figure 200.  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
Figure 201  
7. Press the START (enter) keypad when the correct  
number appears in the VFD.  
NOTE: To program other options, refer to the  
appropriate section.  
C816I  
C816I  
How to Exit Programming Feature  
Figure 200  
1. Be sure the control shows a programmable option,  
not a value.  
4. When “+055” appears in the VFD, press the  
START (enter) keypad. A number will appear in  
the VFD. This number corresponds to the current  
Start Pulse Mode Programming Value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
revert back to the ready mode. Refer to Figure 2.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
107  
       
Notes  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
108  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Collecting Audit Information  
This feature allows the owner to retrieve audit  
Audit Options List  
information stored in the washer by pressing a sequence  
of pads on the control. For an explanation of the audit  
options available, see the Audit Options List on this page.  
VFD  
Display  
#
Description  
“CyCL”  
“COI1”  
“COI2”  
“PLSE”  
“CArd”  
1
2
3
4
5
Total # of machine cycles  
Total # of coins #1  
How to Enter Audit Feature  
1. Control must be in Manual Mode to start. Refer  
Total # of coins #2  
to Entering the Manual Mode.  
Total # of Start Pulses  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “AUdT” appears. Refer to Figure  
202.  
Smart Card Reader Firm Ware Version #  
Table 11  
2. Once the desired option appears in the VFD,  
press the START (enter) keypad once to start the  
audit count. At this point, the display will show  
the first four-digit segment of the audit value.  
Press the START (enter) keypad again to view the  
last four digits of the number.  
C823I  
C823I  
NOTE: The VFD can display up to 4 digits at one  
time. All audit counts are separated into two 4-digit  
segments. Each time the START (enter) keypad is  
pressed in step 2, the VFD will show the next four-  
digit segment in the audit value.  
Figure 202  
3. Press the START keypad. “CyCL” will appear.  
If the procedure did not work, the control will return to  
the ready mode. Refer to Figure 2.  
For Example: In the Total Number of Coins #1 option  
with “COI1” displayed in the VFD, the audit has  
counted 10,009 coins. Pressing the START (enter)  
keypad one time will show “_ _ _ 1” to represent ten  
thousand. Pressing the START (enter) keypad a second  
time will display “0009” meaning nine. The total  
equals “00010009” or 10,009.  
How to Read Audit Data  
1. Use the DELICATES (+) or the COLD (-)  
keypad to scroll through various options until the  
desired option is displayed in the VFD. Refer to  
the Audit Options List, Table 11, for an  
explanation of the audit options available. Refer to  
Figure 203.  
3. Press the START (enter) keypad again. The  
control will go to the next audit option in the  
Audit Options List.  
1
4. To select other audit options, repeat steps 1 – 4.  
How to Exit Audit Feature  
1. Be sure the control shows an audit option, not a  
value.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand. The control will  
return to the ready mode. Refer to Figure 2.  
3
2
C860I  
1
2
Press this pad (+) to scroll forward or increase a value  
Press this pad (enter) to choose a selected value or  
option  
3
Press this pad (-) to scroll back or decrease a value  
Figure 203  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
109  
     
Notes  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
110  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Manual Reset  
This feature allows the owner to reset the washer  
control’s programming data to the factory default  
settings by pressing a sequence of pads on the control.  
For an explanation of the Factory Default Settings,  
refer to Default Washer Settings.  
How to Enter Manual Reset  
1. Control must be in Manual Mode to start.  
Refer to Entering the Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “rSET” appears. Refer to Figure  
204.  
C80
C830I  
Figure 204  
3. Press the START (enter) keypad. The control will  
display “WAIT” until the programming is  
complete. Once the program has been reset, the  
control will revert back to the ready mode.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
111  
 
Notes  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
112  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Testing Machine and  
Electronic Control Functions  
This feature allows the owner to run diagnostic tests  
on various washer operations without servicing the  
washer. The following tests are available:  
How to Enter Testing Feature  
1. Control must be in Manual Mode. Refer to  
Entering the Manual Mode.  
●
●
●
●
●
●
●
●
●
●
●
●
●
Control Software Version Number  
Pressure Switch Opening Test  
Service Door Opening Test  
Coin Vault Opening Test  
Coin Drop #1 Input Test  
Coin Drop #2 Input Test  
Lid Switch Input Test  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “dIAg” appears.  
3. Press the START (enter) keypad. Display will  
change to “+001” indicating the control software  
version number test.  
4. Press the DELICATES (+) or the COLD (-)  
keypad to scroll through the diagnostic test  
options.  
How to Start Tests  
Show Fill Time Test  
Show Drain Time Test  
To start a diagnostic test, refer to the quick reference  
chart below (Table 12). Press the START (enter)  
keypad when the desired test # is displayed. For detailed  
information on each test, read the appropriate description.  
Start Pulse Test  
Configuration #1 Display Test  
Configuration #2 Display Test  
Configuration #3 Display Test  
How to Exit Testing Feature  
While pressing and holding the NORMAL keypad  
with one hand, press the PERM PRESS keypad with  
the other hand. The display will return to the ready  
mode. Refer to Figure 2.  
Diagnostic (Testing) Mode – Quick Reference Chart  
Test Number  
Diagnostic Mode  
VFD Display  
“SXXX”  
“S:XX”  
1
2
Control Software Version # Test  
Service Door Opening Test  
Coin Vault Opening Test  
Coin Drop #1 Input Test  
Coin Drop #2 Input Test  
Lid Switch Input Test  
“U:XX”  
“C1:XX”  
“C2:XX”  
“L:XX”  
3
4
5
6
“PXXX”  
“FX:XX”  
“dX:XX”  
“ST:XX”  
“AXXX”  
“bXXX”  
“CXXX”  
7
Pressure Switch Opening Test  
Show Fill Time Test  
8
9
Show Drain Time Test  
10  
11  
12  
13  
Start Pulse Test  
Configuration #1 Display Test  
Configuration #2 Display Test  
Configuration #3 Display Test  
Table 12  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
113  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Testing Machine and Electronic Control Functions  
Diagnostic Test Descriptions  
Control Software Version Number Test  
Coin Drop #1 Input Test  
This option displays the control software version  
number. To start test, control must be in the Testing  
Mode. Refer to “How to Start Tests” at the beginning  
of this section.  
This option tests coin drop #1. To start test, control  
must be in the Testing Mode. Refer to “How to Start  
Tests” at the beginning of this section.  
To enter, press the START (enter) keypad. The VFD  
display will show “C1:XX”. The “XX” will show the  
number of coins entered. This test will add counts to  
the total number of test coins #1 counter. Refer to  
Collecting Audit Information.  
To enter, press the START (enter) keypad. The VFD  
display will show “SXXX” where “XXX” is the  
software version number.  
To exit the Software Version Number Test, press the  
NORMAL and PERM PRESS keypads. The control  
will return to the ready mode. Refer to Figure 2.  
To exit the Coin Drop #1 Input Test, press the  
NORMAL and PERM PRESS keypads. The control  
will return to the ready mode. Refer to Figure 2.  
Service Door Opening Test  
Coin Drop #2 Input Test  
This option tests the service door switch. To start test,  
control must be in the Testing Mode. Refer to “How to  
Start Tests” at the beginning of this section.  
This option tests coin drop #2. To start test, control  
must be in the Testing Mode. Refer to “How to Start  
Tests” at the beginning of this section.  
To enter, press the START (enter) keypad. The VFD  
display will show “S:XX”. The “XX” will show the  
number of service door openings.  
To enter, press the START (enter) keypad. The VFD  
display will show “C2:XX”. The “XX” will show the  
number of coins entered. This test will add counts to  
the total number of test coins #2 counter. Refer to  
Collecting Audit Information.  
The service door switch has to be closed for at least  
one second and opened for at least a half a second to  
make a valid count. This test will add counts to the  
service door opening counter for the audit and save the  
date/time for each opening of the test.  
To exit the Coin Drop #2 Input Test, press the  
NORMAL and PERM PRESS keypads. The control  
will return to the ready mode. Refer to Figure 2.  
To exit the Service Door Opening Test, press the  
NORMAL and PERM PRESS keypads. The control  
will return to the ready mode. Refer to Figure 2.  
Lid Switch Input Test  
This test will display whether the washer lid is open or  
closed.  
Coin Vault Opening Test  
This option tests the coin vault switch. To start test, the  
control must be in the Testing Mode. Refer to “How to  
Start Tests” at the beginning of this section.  
To start test, control must be in the Testing Mode.  
Refer to “How to Start Tests” at the beginning of this  
section.  
To enter, press the START (enter) keypad. The VFD  
display will show “U:XX”. The “XX” will show the  
number of coin vault openings.  
To enter, press the START (enter) keypad. If the lid is  
closed, the VFD will display “L:CL”. If the lid is open,  
the VFD will display “L:OP”.  
The coin vault switch has to be closed for at least one  
second and opened for at least a half a second to make  
a valid count. This test will add counts to the coin vault  
opening counter for the audit and save the time/date  
for each opening of the test.  
To exit the test, press the NORMAL keypad with one  
hand, then press the PERM PRESS keypad with the  
other hand. The control will return to the ready mode.  
Refer to Figure 2.  
To exit the Coin Vault Opening Test, press the  
NORMAL and PERM PRESS keypads. The control  
will return to the ready mode. Refer to Figure 2.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
114  
Testing Machine and Electronic Control Functions  
To enter, press the START (enter) keypad. The VFD  
display will show “ST:XX”. The “XX” will show the  
number of pulses entered. This test will add counts to  
the total number of Start Pulses counter. Refer to  
Collecting Audit Information.  
Pressure Switch Input Test  
This test will display whether the pressure switch is  
open or closed.  
To start test, control must be in the Testing Mode.  
Refer to “How to Start Tests” at the beginning of this  
section.  
To exit the Start Pulse Test, press the NORMAL and  
PERM PRESS keypads. The control will return to the  
ready mode. Refer to Figure 2.  
To enter, press the START (enter) keypad. The VFD  
display will show “P:OP” if the pressure switch is  
open and “P:CL” if the pressure switch is closed.  
Configuration Display Test  
This option shows the machine configuration values.  
Test #11 shows configuration value #1, Test #12 shows  
configuration value #2, and Test #13 shows configuration  
value #3. To start test, control must be in the Testing  
Mode. Refer to “How to Start Tests” at the beginning  
of this section.  
To exit the test, press the NORMAL keypad with one  
hand, and then press the PERM PRESS keypad with  
the other hand. The control will then return to the  
ready mode. Refer to Figure 2.  
Show Fill Time Test  
To enter, press the START (enter) keypad. For  
configuration value #1, the VFD will show “AXXX”.  
For configuration value #2, the VFD will show “bXXX”.  
For configuration value #3, the VFD will show  
“CXXX”. For all, “XXX” is the value of the number.  
This test will display the average fill time in minutes  
and seconds. This average will be calculated by taking  
the average of the last four (4) fill times.  
To start test, control must be in the Testing Mode.  
Refer to “How to Start Tests” at the beginning of this  
section.  
Refer to tables below for test information.  
To exit a Configuration Display Test, press the  
NORMAL and PERM PRESS keypads. The control  
will return to the ready mode. Refer to Figure 2.  
To enter, press the START (enter) keypad. The VFD  
will show “FX:XX”. The “X:XX” will be the average  
fill time in minutes and seconds for that machine.  
Machine Configuration #1 Table  
To exit the Show Fill Time Test, press and hold the  
NORMAL keypad with one hand, then press the  
PERM PRESS keypad with the other hand. The control  
will return to the ready mode. Refer to Figure 2.  
Value  
129  
Coin #1  
NO  
Coin #2  
NO  
161  
YES  
NO  
NO  
Show Drain Time Test  
193  
YES  
YES  
This test will display the average drain time in minutes  
and seconds. The average drain time is calculated by  
taking the average of the last four (4) drain times.  
225  
YES  
Table 13  
To start the test, press the START (enter) keypad. The  
VFD will show “dX:XX”. The “X:XX” will be the  
average drain time in minutes and seconds for that  
machine.  
Machine Configuration #2 Table  
Smart Card  
Value  
Network Board  
Reader  
0
NO  
NO  
NO  
To exit the Show Drain Time Test, press and hold the  
NORMAL keypad with one hand, then press the  
PERM PRESS keypad with the other hand. The control  
will return to the ready mode. Refer to Figure 2.  
32  
64  
96  
YES  
NO  
YES  
YES  
YES  
Start Pulse Test  
Table 14  
This option tests the Start Pulse. To start test, control  
must be in the Testing Mode. Refer to “How to Start  
Tests” at the beginning of this section.  
Machine Configuration #3 – unused.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
115  
Notes  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
116  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Error Codes  
Following is a list of possible error codes for an  
electronic control. Errors beginning with “EI” refer to  
NetMaster Infra-red communication errors. Errors  
beginning with “EC” refer to NetMaster card reader  
errors. All other errors refer to electronic control  
errors.  
Cause/  
Display  
EI:01  
Description  
Transmission Failure  
Corrective Action  
Communication failure. Re-aim Micro-Wand and try  
again.  
EI:02  
EI:03  
EI:04  
EI:05  
EI:06  
Device Timeout  
Communication failure. Re-aim Micro-Wand and try  
again.  
Invalid Command Code  
Expecting Upload Request  
Invalid or Out-of-Range Data  
Invalid Data Code  
Incorrect machine type. Before downloading, ensure  
data is for current machine type.  
Communication failure. Re-aim Micro-Wand and try  
again.  
Incorrect machine type. Before downloading, ensure  
data is for current machine type.  
Incorrect machine type. Before downloading, ensure  
data is for current machine type.  
EI:07  
EI:08  
EI:09  
Error Writing to RTC  
Error Writing to EEPROM  
CRC-16 Error  
Control failure. Replace control.  
Control failure. Replace control.  
Communication failure. Re-aim Micro-Wand and try  
again.  
EI:0A  
EI:0F  
Invalid Machine Type  
Incorrect machine type. Before downloading, ensure  
data is for current machine type.  
Invalid Wakeup or Infra-red Disabled  
Communication failure or infra-red is disabled.  
Manually enable infra-red on control or re-aim Micro-  
Wand and try again.  
EC:00  
EC:02  
EC:03  
General Communication Error  
Timeout Error  
Communication failure. Try card again.  
Communication failure. Try card again.  
Invalid Command Code  
Incorrect machine type. Before downloading, ensure  
data is for current machine type.  
EC:05  
EC:06  
Invalid or Out-of-Range Data  
Invalid Data Code  
Incorrect machine type. Before downloading, ensure  
data is for current machine type.  
Incorrect machine type. Before downloading, ensure  
data is for current machine type.  
EC:09  
EC:0A  
Corrupted Data Error  
Invalid Machine Type  
Communication error. Try card again.  
Incorrect machine type. Before downloading, ensure  
data is for current machine type.  
EC:19  
No Card Reader Communication  
Communication failure. Power down, power up and try  
again. If error persists, replace control or card reader.  
Table 15  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
117  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Error Codes  
Cause/  
Display  
Description  
Unreadable Card  
Corrective Action  
EC:20  
Faulty card or dirty contact. Clean chip on card or card  
reader contacts. Try card again. If error persists, card  
may be faulty.  
EC:21  
EC:22  
EC:23  
Security ID Mismatch  
Incorrect card. Use card with correct security code.  
Incorrect card. Use card with correct site code.  
Site Code Mismatch  
Card Maximum Value Exceeded  
Value on card over max. Use a card which does not  
exceed maximum value.  
EC:24  
Insufficient Memory on Card  
Card memory is full. Download card contents to PC and  
clear card for re-use.  
EC:25  
EC:26  
EC:27  
EC:28  
EC:29  
EC:2A  
EC:2b  
EC:2C  
EC:2d  
Card Reader Malfunction  
Faulty card reader. Replace card reader.  
Try card again. If error persists, card may be faulty.  
Faulty card reader. Replace card reader.  
Faulty card reader. Replace card reader.  
Faulty card reader. Replace card reader.  
Faulty card reader. Replace card reader.  
Card Write Error  
Diagnostic Test Card Write Failure  
Diagnostic Test Card Read Failure  
Diagnostic Test Memory Test Failure  
Diagnostic Test Card Interface Failure  
Diagnostic Test Flash Checksum Failure Faulty card reader. Replace card reader.  
Biberon or Non-biberon Device Failure  
Faulty card reader. Replace card reader.  
Firmware load failed. Replace card reader.  
Firmware Update Failed,  
S/W (Software) Intact  
EC:2E  
EC:2F  
EC:30  
EC:31  
EC:50  
EC:56  
Firmware Update Failed, S/W Not Intact Faulty firmware in reader. Replace card reader.  
Firmware Updated, S/W Not Intact  
Timeout Error  
Faulty firmware in reader. Replace card reader.  
Replace card reader.  
Hotlisted Card Inserted Into Reader  
Loyalty Purse Read Error  
Loyalty Purse Write Error  
Card hotlisted. Control will destroy card.  
Try card again. If error persists, card may be faulty.  
Try card again. If error persists, card may be faulty.  
Right most Network Communication Error  
DP (decimal  
point)  
Communication problem. Wait for 1.5 minutes for error  
to clear. If error doesn’t clear, power-down and power-  
up the machine. If error persists, replace control or  
network board.  
Lit  
Alrm  
OFF  
E:FL  
Break-in Alarm Error  
Break-in Alarm Shutdown Error  
Fill Error  
Service the door or coin vault switches.  
Service the door or coin vault switches.  
Pressure switch fails to open in 30 minutes in any fill  
agitate cycle.  
E:dr  
Drain Error  
Maximum drain time exceeded or water sensed at end of  
spin step.  
Table 15  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
118  
Error Codes  
Cause/  
Display  
Err  
Description  
Corrective Action  
Coin Error  
Invalid coin pulse or inoperative coin sensor. Check coin  
drop area and remove obstructions. If error persists,  
tampering may have occured. Evaluate security  
procedures.  
Table 15  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
119  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Notes  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
120  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sales Floor Feature  
The Sales Floor feature is used on a sales floor to  
allow the owner to turn on the entire VFD display and  
all LEDs.  
How to Exit Sales Floor Feature  
1. Be sure service door is open.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the PERM PRESS  
keypad with the other hand.  
How to Enter Sales Floor Feature  
1. Control must be in Manual Mode to start. Refer  
to Entering the Manual Mode.  
The display will return to the ready mode. Refer to  
Figure 2.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “SHOW” appears.  
3. Press the START (enter) keypad.  
The display will light up.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
121  
Notes  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
122  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rapid Advance Feature  
The Rapid Advance feature allows the owner to  
quickly advance through active cycles or advance into  
a cycle from the ready mode.  
How to Exit Rapid Advance Feature  
1. Advance through the cycles until reaching the  
ready mode. Refer to Figure 2.  
How to Enter Rapid Advance from  
Ready Mode  
NOTE: The Rapid Advance/Diagnostic Access  
option must be turned on for Rapid Advance to  
work. Refer to option 47 in Programming  
NetMaster.  
1. If control is in Ready Mode, control must be put  
into Manual Mode. Refer to Entering the  
Manual Mode.  
2. Press the DELICATES (+) or the COLD (-)  
keypad until “rAPd” appears in the display.  
3. Press the START (enter) keypad. The VFD will  
display cycle time and the START (enter) keypad  
LED will flash.  
4. Press the START (enter) keypad to start cycle.  
How to Enter Rapid Advance During  
an Active Cycle  
1. Be certain service door is open.  
2. While pressing and holding the NORMAL  
keypad with one hand, press the HOT keypad  
with the other hand. There will be no change on  
the VFD display.  
Control may be in an active cycle or in the ready mode  
to use the Rapid Advance feature.  
While in the Rapid Advance Mode, pressing the  
START (enter) keypad will advance the washer to the  
next cycle step. The cycle indicator lights will tell  
which cycle step the washer is in.  
For Example: If the washer is in the wash fill/agitate  
cycle step, pressing the START (enter) keypad will  
advance the washer into the WASH PAUSE cycle step.  
Continue pressing the START (enter) keypad until the  
cycle is completed.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
123  
Notes  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
124  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Clear Vend Feature  
The Clear Vend feature allows the owner to clear a  
control which is in the middle of satisfying a vend  
price, and set it back to the ready mode.  
How to Clear Vend  
1. Open the service door. Refer to Opening the  
Service Door.  
2. While pressing and holding the HOT keypad with  
one hand, press the PERM PRESS keypad with  
the other hand. The control will reset to the ready  
mode. Refer to Figure 2.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
125  
Notes  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
126  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Power Fail Recovery  
The Power Fail Recovery feature allows the cycle status  
to be saved in memory in the event of a power failure.  
Power Fail Reset Enabled  
If the length of the power failure is less than the  
programmed Power Failure Reset time, the control  
will resume the cycle from the point it left off. The  
cycle will resume automatically unless the EC Power  
Fail feature is enabled and the failure lasted more than  
two (2) seconds which requires the user to press the  
START pad.  
If a cycle is in progress when the power fails, the cycle  
status is saved in memory. When power recovers, the  
control will determine whether to automatically  
continue the cycle from the point it left off, requiring  
the user to press the START pad to continue the cycle,  
or end the cycle and put the control into the Ready  
Mode.  
If the power failure lasted more than the programmed  
power failure reset time, the contol will end the cycle  
and will return to the Ready Mode. If, however, the  
cylinder is filled with water when the power recovers,  
the control will not go directly to Ready Mode, but  
will spin out the water first. In this case the control  
will enter the Start Mode at the Rinse Spin #1 step of  
the DELICATE Cycle prompting the user to press the  
START pad. Once the START pad is pressed, the  
control will start the Rinse Spin #1 step, then the Final  
Spin step and then end the cycle.  
Power Fail Reset Disabled  
If the European Community (EC) Power Fail feature is  
disabled, the control will automatically resume the  
cycle from the point it left off. Whenever the EC  
Power Fail feature is enabled and the power failure  
lasted more than two (2) seconds, the control will go  
back to the Start Mode and will prompt the user to  
press the START pad to continue the cycle from the  
point it left off.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
127  
Notes  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
128  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Communications Mode  
Infra-red Communications  
Card Reader Communications  
(Card Models Only)  
The Infra-red Communications feature allows the  
washer control to communicate with the Micro-Wand  
IIIE. The washer control can be programmed and have  
its data read without using the keypad. It may also be  
used to start and stop various diagnostic tests.  
The Card Reader Communications feature allows the  
washer control to communicate with the Card Reader.  
The washer control can be programmed and have its  
data read without using the keypad.  
How to Begin Communications with  
Micro-Wand IIIE  
Network Communications  
The Network Communications feature allows the  
washer control to communicate with the Network. The  
washer control can be programmed and have its data  
read without using the keypad.  
The control will go blank and the VFD will display  
“-C-” until the communication is complete. The  
display will return to the previous mode. If an error  
occurs that terminates communication, the VFD will  
display “EI:XX” (“XX” represents the error code).  
NOTE: The Infra-red Communications option  
must be turned on. Refer to option 46 in  
Programming NetMaster.  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
Download from Www.Somanuals.com. All Manuals Search And Download.  
129  
Notes  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
130  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Default Washer Settings  
Default Settings  
Default Cycle  
The cycle listed is the default PERM PRESS cycle  
Cycle  
PERM PRESS  
WARM  
programmed in at the factory. This cycle can be made  
longer or shorter by reprogramming the agitate times.  
Refer to Programming NetMaster section to change  
these times. All other times are not programmable.  
Wash Water Temperature  
Rinse Water Temperature  
Special Vends  
COLD  
OFF. All items zero.  
Cycle  
Default  
Signals:  
Wash Fill  
Wash Agitate  
Wash Pause  
2:00  
10:00*  
0:10  
0:00  
1:30  
0:30  
1:30  
0:00  
0:00*  
0:00  
0:00  
3:00  
2:00  
4:00*  
0:10  
0:00  
1:30  
6:00*  
Keypress  
End of Cycle  
Coin Input/Card Insertion ON  
ON  
OFF  
Wash Pump  
Remove Card  
Coin #1 Value  
Coin #2 Value  
Power Fail Reset  
ON  
Wash Spin #1  
Wash Spin/Spray  
Wash Spin #2  
Extra Rinse Fill  
Extra Rinse Agitate  
Extra Rinse Pause  
Extra Rinse Pump  
Extra Rinse Spin #1  
Rinse Fill  
Rinse Agitate  
Rinse Pause  
Rinse Pump  
Rinse Spin #1  
Final Spin  
.25  
1.00  
OFF/5 minutes  
Control Configuration:  
Daylight Savings  
Wash Temp Indicator  
Infra-red Access  
Decimal Point  
ON  
SELECT (OFF)  
ON  
ON  
ON  
OFF  
Auto Collect  
EC Power Fail  
* = Programmable Times  
210140  
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT  
131  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Acoustic Research Speaker System HC6 User Manual
AEG Refrigerator K 7 10 43 4 I User Manual
Agilent Technologies Video Games E8285A User Manual
Agilent Technologies Water Dispenser Model A08xx User Manual
Aiphone Intercom System IS Series User Manual
AKG Acoustics Microphone C 426B User Manual
American Dish Service Dishwasher 5 CD LF RF User Manual
American Standard Laminate Trimmer Reliant 3 Bath and Shower Trim Kits with EverClean Finish User Manual
Axor Plumbing Product 14876001 User Manual
Axxess Interface Automobile Parts OESWC LAN29 STK User Manual