ALESIS M 20
P ROFESSIONAL 20 -BIT DIGITAL
RECORDER
OW NER’S M ANUAL
FIRST EDIT ION VERSION 1.0 6
AP P LIES TO OP ERAT ING SOFT W ARE VERSION 1.11
INCLUDES SOFTW ARE VERSION 2.10 ADDENDUM
Ó19 9 9 ALESIS CORP ORAT ION
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONT ENT S
Im p o r t a n t Sa fe t y In s t r u ct io n s a n d Co m p lia n ce No t ice s ...................................... vii
Safety symbols used in this product ................................................................................................ vii
Please follow these precautions when using this product: ............................................................ vii
Instructions de Sécurité Importantes .................................................................................................ix
Symboles utilisés dans ce produit ......................................................................................................ix
Beim Benutzen dieses Produktes beachten Sie bitte die folgenden Sicherheitshinweise: ..............x
Information to the User for Class A Digital Device (FCC Part 15, Class A)...................................xi
CE Declaration of Conformity...........................................................................................................xii
Ove r vie w , Se t u p , a n d Ba s ics .............................................................................. 1
1.1 M20 Highlights ..............................................................................................................................1
1.2 Unpacking and Inspection ............................................................................................................2
1.3 AC Power Hookup ........................................................................................................................2
1.4 Line Conditioners and Protectors.................................................................................................3
1.5 About Audio Cables ......................................................................................................................3
1.6 Basic Audio Hookup .....................................................................................................................4
1.7 Use the Right Tape.........................................................................................................................4
1.8 Preparing the Tape Prior to Use ...................................................................................................4
1.9 Eject Tape Properly........................................................................................................................4
1.10 Backup ..........................................................................................................................................4
1.11 Operating Environment ..............................................................................................................5
1.12 Avoid Electromagnetic Interference...........................................................................................5
Co n t r o l a n d Co n n e ct o r Ba s ics ............................................................................ 1
2.1 About the Front Panel ...................................................................................................................1
2.2 About the Rear Panel.....................................................................................................................3
2.2a Punch Footswitch ...........................................................................................................3
2.2b Locate/ Play or LRC Remote Control Jack ...................................................................3
2.2c Analog Inputs and Outputs...........................................................................................3
2.2d Time Code In and Out...................................................................................................3
2.2e Word Clock In and Out .................................................................................................3
2.2f ADAT Optical In and Out..............................................................................................3
2.2g Video In and Thru..........................................................................................................4
2.2h ADAT Sync In and Out .................................................................................................4
2.2i MIDI In and Out .............................................................................................................4
2.2j RS-422 In (Sony 9-Pin).....................................................................................................4
2.2k Meter Bridge/ Remote Panel Out..................................................................................4
2.2l Power ...............................................................................................................................4
Ed it in g M 20 Op e r a t in g P a r a m e t e r s .................................................................... 1
3.1 The Keypad ....................................................................................................................................1
3.1a 0 through 9 buttons ........................................................................................................1
3.1b Up Arrow/ Yes/ Upper Case.........................................................................................1
3.1c Down Arrow/ No/ Lower Case.....................................................................................1
3.1d Cursor Left .....................................................................................................................1
3.1e Cursor Right ...................................................................................................................1
3.1f Enter/ Name ....................................................................................................................2
3.1g Selecting Pages ...............................................................................................................3
3.1h Selecting Page Parameters.............................................................................................3
3.1i Entering Parameter Values.............................................................................................3
3.2 The Edit Button ..............................................................................................................................4
ALESIS M 20 REFERENCE M ANUAL 1.0 6
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Ta b le o f Co n t e n t s
3.3 Editing Conventions......................................................................................................................4
Ta p e Fo r m a t t in g ...............................................................................................1
4.1 Sample Rate Selection....................................................................................................................2
4.1a Pull-up and Pull-down Sample Rate Selection ............................................................3
4.2 Word Length Selection ..................................................................................................................3
4.3 Format a New Tape .......................................................................................................................4
4.4 Record Tracks While Formatting..................................................................................................4
4.5 Extend a Partially-Formatted Tape ..............................................................................................5
4.6 End Formatting ..............................................................................................................................5
4.7 Certify Tape Format ......................................................................................................................5
4.8 Reformatting: Caution!..................................................................................................................5
4.9 Lock Out Formatting (Safe Mode).................................................................................................6
4.10 Bulk Erasing .................................................................................................................................6
4.11 Recording a “Benchmark” Tape .................................................................................................6
T r a ck Re co r d En a b lin g a n d M o n it o r in g ..............................................................1
5.1 Track Basics....................................................................................................................................1
5.2 Track Input Enables.......................................................................................................................2
5.3 Auto Input Switch .........................................................................................................................2
5.4 Record Enable ................................................................................................................................2
5.5 Safety Mode (All Safe)...................................................................................................................3
5.6 Monitor Inputs (All Input)............................................................................................................3
Dig it a l/An a lo g In p u t Se le ct io n a n d Ro u t in g ........................................................1
6.1 Digital Source.................................................................................................................................1
6.2 Input Select.....................................................................................................................................1
6.3 Track Output Selection..................................................................................................................2
6.4 Input Signal Routing (Analog And Digital).................................................................................2
6.4a Analog Input Routing ....................................................................................................3
6.4b Digital Input Routing.....................................................................................................4
6.4c Record-Enabling the Destination Tracks ......................................................................5
6.5 Aux Routing (input and output) ..................................................................................................6
M e t e r in g 1
7.1 Meter Mode Selection....................................................................................................................1
7.1a Clearing Peaks ................................................................................................................1
7.2 Meter Setup ....................................................................................................................................2
Tr a n s p o r t Co n t r o ls a n d Ba s ic Re co r d in g .............................................................1
8.1 About the Tape Counter................................................................................................................1
8.2 Stop .................................................................................................................................................1
8.3 Play .................................................................................................................................................2
8.3a Play Button and Sync Status..........................................................................................2
8.4 Jog/ Shuttle Wheel and Search ......................................................................................................2
8.4a Jog Mode.........................................................................................................................2
8.4b Shuttle Mode ..................................................................................................................3
8.4c Search Button ..................................................................................................................3
8.4d Search Master.................................................................................................................4
8.5 Other Transport Buttons ...............................................................................................................5
8.6 Record .............................................................................................................................................6
8.6a Punching Into Record ....................................................................................................6
8.6b Punching Out of Record ................................................................................................6
8.6c Record Write-Protection ................................................................................................7
8.6d Recording with a Footswitch ........................................................................................7
8.7 Rehearse Mode................................................................................................................................7
8.8 Auto Record ...................................................................................................................................8
ii
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ta b le o f Co n t e n t s
8.8a Setting Auto Record Punch Points................................................................................8
8.8b Enable Auto Record .......................................................................................................9
8.8c Set Auto Punch Points “On the Fly” .............................................................................9
Au t o lo ca t io n .................................................................................................... 1
9.1 Entering, Selecting, and Editing Location Points ........................................................................1
9.1A Set Locate........................................................................................................................1
9.1B Copy Tape Location........................................................................................................1
9.2 Deferred Play and Record .............................................................................................................3
9.3 Play-After-Locate (Auto Play) ......................................................................................................3
9.4 Loop Between Start and End Locate Points (Auto Return)........................................................3
9.4a Setting Loop Start and End Points................................................................................4
9.5 Set Pre-Roll.....................................................................................................................................4
9.6 Set Post-Roll ...................................................................................................................................5
9.7 Footswitch-Controlled Location ...................................................................................................6
Va r is p e e d ........................................................................................................ 1
SM P TE, Syn c, a n d Offs e t Fu n ct io n s ................................................................... 1
11.1 Clock Source.................................................................................................................................1
11.2 SMPTE Rate..................................................................................................................................2
11.3 Time Code Source........................................................................................................................2
11.3a Internal ...........................................................................................................................2
11.4 Chase Reference ...........................................................................................................................3
11.5 Reference Counter .......................................................................................................................4
11.6 SMPTE Chase ...............................................................................................................................4
11.6a Set SMPTE Offset Value (Page 1)................................................................................4
11.6b Set SMPTE Chase Mode (Page 2)................................................................................5
11.6c Set Flywheel Duration (Page 3) ...................................................................................5
11.6d Park Ahead (Page 4) ....................................................................................................5
11.7 Internal Generator........................................................................................................................6
11.7a Generator Mode (Page 1).............................................................................................6
11.7b Time Code Start Reference (Page 2) ...........................................................................7
11.7c ABS/ Start Offset (Page 3)............................................................................................7
11.7d User Bits (Page 4, or Page 3 if the Page 2 value is TC Track)...................................8
11.8 Tape Offset ...................................................................................................................................8
11.9 Track Delay ................................................................................................................................10
M IDI Fu n ct io n s ................................................................................................. 1
12.1 MIDI Device (Page 1)...................................................................................................................1
12.2 MMC Output (Page 2).................................................................................................................1
12.3 MTC Follow Gen (Page 3)...........................................................................................................1
12.4 Send Sysex Dump? (Page 4)........................................................................................................1
12.5 Receive Sysex Dump? (Page 5) ...................................................................................................2
12.6 Send Software? (Page 6) ..............................................................................................................2
12.7 Load Software? (Page 7)..............................................................................................................2
Ut ilit y M e n u ..................................................................................................... 1
13.1 Digital Out (Page 1) .....................................................................................................................1
13.2 Online Source (Page 2).................................................................................................................1
13.2a Online Button................................................................................................................1
13.2b Independent Slave Mode.............................................................................................2
13.3 Online Control (Page 3)...............................................................................................................2
13.4 One-Button Record (Page 4)........................................................................................................2
13.5 Input Monitor (Page 5) ................................................................................................................2
13.6 Crossfade Time (Page 6)..............................................................................................................3
13.7 Time Code Output Level (Page 7)..............................................................................................3
ALESIS M 20 REFERENCE M ANUAL 1.0 6
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Ta b le o f Co n t e n t s
13.8 Rewind/ Fast Forward TC Output (Page 8)...............................................................................3
13.9 Unthread Timeout (Page 9).........................................................................................................3
13.10 Search Enable (Page 10).............................................................................................................4
13.11 Locate Before Play (Page 11).....................................................................................................4
13.12 Mute Until Lock (Page 12).........................................................................................................4
13.13 Dynamic Punch (Page 13)..........................................................................................................4
13.14 Track Groups (Page 14) .............................................................................................................4
13.15 Save Data to Tape? (Page 15)....................................................................................................4
13.16 Load Data from Tape? (Page 16) ..............................................................................................5
13.17 Tape Type (Page 17)...................................................................................................................5
13.18 ID Status (Page 18).....................................................................................................................5
13.19 User Bits (Page 19) .....................................................................................................................5
13.20 Error Rate (Page 20)...................................................................................................................6
13.21 Front Panel Software Version (Page 21)...................................................................................6
13.22 Software Version (Page 22) .......................................................................................................6
Th e LRC Re m o t e Co n t r o l....................................................................................1
T u t o r ia ls a n d Ap p lica t io n s ................................................................................1
TUTORIAL 1: Multiple M20 Operation..............................................................................................1
Overview .................................................................................................................................1
Synchronizing Machines ........................................................................................................1
Automatic ID Renumbering...................................................................................................1
Master/ Slave Interaction........................................................................................................2
Achieving Lock .......................................................................................................................2
Independent Slave Mode........................................................................................................2
Formatting Multiple Tapes ..................................................................................................................3
Master Format Enabled, Complete Format ..........................................................................3
Master Format Enabled, Format Extend ...............................................................................3
Master Format Disabled .........................................................................................................4
Master Format Disabled, Format Extend..............................................................................4
TUTORIAL 2: Making Digital Backups ..............................................................................................5
Dealing with Damaged Tape .................................................................................................6
Making a 16-bit copy from a 20-bit master ...........................................................................6
TUTORIAL 3: Recording Digital Audio from Other Sources...........................................................7
Digital Clock Considerations .................................................................................................7
TUTORIAL 4: Combining M20s and ADATs ....................................................................................8
M20 Transport Speed .............................................................................................................8
Sample rate vs. Pitch Control.................................................................................................8
Input Monitoring ....................................................................................................................8
Polarity Differences ................................................................................................................9
TUTORIAL 5: Setting up Inputs........................................................................................................10
TUTORIAL 6: Updating M20 Software ............................................................................................11
TUTORIAL 7: Using the M20 with Unbalanced Inputs and Outputs............................................12
M 20 SM P TE Syn ch r o n iz a t io n Ove r vie w ..............................................................1
16.1 Synchronization Basics .................................................................................................................1
Master or Slave?......................................................................................................................1
Digital Timing Requirements.................................................................................................1
16.2 The One Clock Principle..............................................................................................................2
16.2a House Sync ...................................................................................................................2
16.2b “Genlocked” Time Code...............................................................................................2
16.3 Reference Counters vs. Clock Sources .......................................................................................3
16.3a Location Reference ........................................................................................................3
16.3b Reference Clock .............................................................................................................3
16.3 Offsets in the M20........................................................................................................................5
iv
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ta b le o f Co n t e n t s
16.3a SMPTE Chase Offset ....................................................................................................5
16.3b Internal Generator ABS Offset .....................................................................................6
16.3c Tape Offset....................................................................................................................6
16.4 SMPTE Time Code Rates and Types...........................................................................................7
16.4a Drop Frame....................................................................................................................7
16.4b Auto-detection of SMPTE Rates ..................................................................................7
16.4c VITC (Vertical Interval Time Code)............................................................................8
16.4d MTC (MIDI Time Code)...............................................................................................8
Tim e Co d e Tu t o r ia l ........................................................................................... 1
17.1 Generating Time Code onto a VCR............................................................................................1
17.2 Synchronizing Without a T/ C Track...........................................................................................2
17.3 Recording a Time Code Track ....................................................................................................3
17.3a Recording SMPTE from ABS Time ..............................................................................3
M a in t e n a n ce a n d Tr o u b le s h o o t in g ..................................................................... 5
18.1 ADAT Head Cleaning .................................................................................................................5
18.1a Head Cleaning Cassettes (optional)............................................................................6
18.1b Manual Head and Tape Path Cleaning ......................................................................6
18.2 ADAT Head Life..........................................................................................................................7
18.2a Head Alignment ...........................................................................................................7
18.3 Tape Maintenance: Safe Tape .....................................................................................................8
18.3a Tape Wear .....................................................................................................................8
18.3b Care of ADAT Tapes ...................................................................................................8
18.4 Maintenance/ Service...................................................................................................................9
18.4a Exterior Cleaning..........................................................................................................9
18.4b Maintenance .................................................................................................................9
18.4d Obtaining Repair Service...........................................................................................10
M 20 Hid d e n Fu n ct io n s ...................................................................................... 1
Power-On Button Combinations .........................................................................................................1
Miscellaneous Button Combinations ..................................................................................................1
Advanced Functions.............................................................................................................................3
Us in g Th e M 20 Da t a Se ct io n Of Ta p e ................................................................. 1
General data section convention on the M20 .....................................................................................1
M20 Locate Points and SMPTE Offsets ..............................................................................................1
BRC Û M20 Song Start / SMPTE Start Offset and Locate Point Map.............................................1
BRC Û M20 Parameter Map ...............................................................................................................2
M 20 Tr a n s p o r t & Sys t e m Er r o r M e s s a g e s ........................................................... 1
M 20 M a jo r Fe a t u r e Up d a t e : Ve r s io n 2 ................................................................ 1
RS-422 (Sony 9-pin) slave operation....................................................................................................1
RS-422 Track Arm: On/ Off....................................................................................................1
RS-422 Mapping: 1-2, OddEvn, (Local).................................................................................1
ID 1 offline with the CADI remote......................................................................................................2
CADI Tape and Reference Counter indications when ID 1 is offline...............................................2
Storing locate points when ID 1 is offline...........................................................................................2
Tape TC detection in fast wind modes ...............................................................................................3
Tape TC in the Tape Counter ..............................................................................................................4
Fixed mode time code generation: “TC Start Ref: Fixed” .................................................................4
Digital Scrub: “Dig Scan: On/ Off, nn dB”..........................................................................................5
I/ O Card as the digital source.............................................................................................................5
SMPTE Chase with the Stop button ....................................................................................................5
Tape TC updating when in Input mode .............................................................................................5
Vari-Speed and Pull-Up/ Down ..........................................................................................................5
ALESIS M 20 REFERENCE M ANUAL 1.0 6
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Ta b le o f Co n t e n t s
MIDI Thru .............................................................................................................................................6
New Utility page order ........................................................................................................................6
CADI display changes..........................................................................................................................6
Cassette Auto-Inject .............................................................................................................................6
Deck Standby Mode .............................................................................................................................7
Auto-Park After Formatting ................................................................................................................7
Deferred Eject .......................................................................................................................................7
New RS-422 Device ID .........................................................................................................................7
Improved SMPTE Clock Source Recognition.....................................................................................7
Sample Rate Change During Play/ Record .........................................................................................7
vi
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
IM P ORTANT SAFET Y
INST RUCT IONS AND COM P LIANCE
NOT ICES
SAFETY SYM BOLS USED IN THIS P RODUCT
This symbol alerts the user that there are important operating and
maintenance instructions in the literature accompanying this unit.
This symbol w arns the user of uninsulated voltage w ithin the
unit that can cause dangerous electric shocks.
P LEASE FOLLOW THESE P RECAUTIONS W HEN USING THIS
P RODUCT:
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a damp cloth.
Do not spray any liquid cleaner onto the faceplate, as this may damage the front panel
controls or cause a dangerous condition.
7. Do not block any of the ventilation openings. Install in accordance with the
manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
(more on next page)
ALESIS M 20 REFERENCE M ANUAL 1.0 6
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Sa fe t y No t ice s
9. Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has tw o blades w ith one w ider than the other.
A grounding-type plug has tw o blades and a third grounding prong.
The w ide blade or the third prong is provided for your safety. When
the provided plug does not fit into your outlet, consult an electrician
for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Use only attachments/ accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, rack, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/ apparatus combination to avoid injury from tip-over.
Alesis recommends the use of standard 19” racks designed for use with professional audio
or music equipment, and the use of rear rack rail supports or sliders. In any installation,
make sure that injury or damage will not result from cables pulling on the apparatus and
its mounting.
13. Unplug this apparatus during lightning storms or when unused for long periods
of time.
14. Refer all servicing to qualified service personnel. Servicing is
required w hen the apparatus has been damaged in any w ay,
such as w hen the pow er-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
15. This unit produces heat when operated normally. If this unit is installed in a rack, make
sure that there is proper ventilation when operated. Do not operate in an enclosed rack
with closed front and back doors. If there are other units in the rack that generate a large
amount of heat, spread them apart. Do not sandwich this product between two large
heat-producing units.
16. This product, in combination with an amplifier and headphones or speakers, may be capable of
producing sound levels that could cause permanent hearing loss. Do not operate for a long period
of time at a high volume level or at a level that is uncomfortable. If you experience any hearing
loss or ringing in the ears, you should consult an audiologist.
viii
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Sa fe t y No t ice s
INSTRUCTIONS DE SÉCURITÉ IM P ORTANTES
SYM BOLES UT ILISÉS DANS CE P RODUIT
Ce symbole alèrte l’utilisateur qu’il existe des instructions de fonctionnement et de maintenance
dans la documentation jointe avec ce produit.
Ce symbole avertit l’utilisateur de la prèsence d’une tension non isolèe à l’intèrieur de l’appareil pouvant
engendrer des chocs èlectriques.
Ve u ille z s u ivr e ce s p r è ca u t io n s lo r s d e l’u t ilis a t io n d e
l’a p p a r e il:
1. Lisez ces instructions.
2. Gardez ces instructions.
3. Tenez compte de tous les avertissements.
4. Suivez toutes les instructions.
5. N’utilisez pas cet allareil à proximitè de l’eau.
6. Ne nettoyez qu’avec un chiffon humide. Ne pas vaporiser de liquide nettoyant sur
l’appareil, cela pourrait abîmer les contrôles de la face avant ou engendrer des conditions
dangeureuses.
7. Installez selon les recommandations du constructeur.
8. Ne pas installer à proximilè de sources de chaleur comme radiateurs, cuisinière ou autre
appareils (don’t les amplificateurs) produisant de la chaleur.
9. Ne pas enlever la prise de terre du cordon secteur. Une prise murale avec terre deux
broches et une troisièrme relièe à la terre. Cette dernière est prèsente pour votre sècuritè.
Si le cordon secteur ne rentre pas dans la prise de courant, demandez à un èlectricien
qualifiè de remplacer la prise.
10. Evitez de marcher sur le cordon secteur ou de le pincer, en particulier au niveau de la
prise, et aux endroits où il sor de l’appareil.
11. N’utilisez que des accessoires spècifiès par le constructeur.
12. N’utilisez qu’avec un stand, rack ou table conçus pour l’utilisation d’audio professionnel
ou instruments de musique. Dans toute installation, veillez de ne rien endommager à
cause de câbles qui tirent sur des appareils et leur support.
13. Dèbranchez l’appareil lors d’un orage ou lorsqu’il n’est pas utilisè pendant longtemps.
14. Faites rèparer par un personnel qualifiè. Une rèparation est nècessaire lorsque l’appareil
a ètè endommagè de quelque sorte que ce soit, par exemple losrque le cordon secteur ou
la prise sont endommagès, si du liquide a coulè ou des objets se sont introduits dans
l’appareil, si celui-ci a ètè exposè à la pluie ou à l’humiditè, ne fonctionne pas
normalement ou est tombè.
15. Cet appareil produit de la chaleur en fonctionnement normal. Si cet appareil est utilisè
dans un rack, veillez à sa bonne ventilation lors de son utilisation. Ne pas faire
fonctionner dans un rack fermè. S’il y a d’autres appareils dans le rack gènèrant
beaucoup de chaleur, èloignez les. Ne pas intercaler cet appareil entre deux appareils
produisant beaucoup de chaleur.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Sa fe t y No t ice s
16. Ce produit, utilisè avec un amplificateur et un casque ou des enceintes, est capable de
produite des niveaux sonores pouvant engendrer une perte permanente de l’ouïe. Ne
l’utilisez pas pendant longtemps à un niveau sonore èlevè ou à un niveau non
confortable. Si vous remarquez une perte de l’ouïe ou un bourdonnement dans les
oreilles, consultez un spècialiste.
BEIM BENUTZEN DIESES P RODUKTES BEACHTEN SIE
BITTE DIE FOLGENDEN SICHERHEITSHINW EISE:
1. Lesen Sie die Hinweise.
2. Halten Sie sich an die Anleitung.
3. Beachten Sie alle Warnungen.
4. Beachten Sie alle Hinweise.
5. Bringen Sie das Gerät nie mit Wasser in Berührung.
6. Verwenden Sie zur Reinigung nur ein weiches Tuch. Sprühen Sie keine flüssiger
Reiniger auf die Oberfläche, dies könnte zur Beschädigung der Vorderseite führen und
auch weitere Schäden verursachen.
7. Halten Sie sich beim Aufbau des Gerätes an die Angaben des Herstellers.
8. Stellen Sie das Gerät nich in der Nähe von Heizkörpern, Heizungsklappen oder anderen
Wärmequellen (einschließlich Verstärkern) auf.
9. Verlegen Sie das Netzkabel des Gerätes niemals so, daß man darüber stolpern kann oder
daß es gequetscht wird.
10. Benutzen Sie nur das vom Hersteller empfohlene Zubehör.
11. Verwenden Sie ausschließlich Wagen, Ständer, Racks oder Tische, die speziell für
professionelle Audio- und Musikinstrumente geeignet sind. Achten Sie immer darauf,
daß die jeweiligen Geräte sicher installiert sind, um Schäden und Verletzungen zu
vermeiden. Wenn Sie einen Rollwagen benutzen, achten Sie darauf, das dieser nicht
umkippt, um Verletzungen auszuschließen.
12. Ziehen Sie während eines Gewitters oder wenn Sie das Gerät über einen längeren
Zeitraum nicht benutzen den Netzstecher aus der Steckdose.
13. Die Wartung sollte nur durch qualifiziertes Fachpersonal erfolgen. Die Wartung wird
notwendig, wenn das Gerät beschädigt wurde oder aber das Stromkabel oder der
Stecker, Gegenstände oder Flüssigkeit in das Gerät gelangt sind, das Gerät dem Regen
oder Feuchtigkeit ausgesetzt war und deshalb nicht mehr normal arbeitet oder
heruntergefallen ist.
14. Bei normalem Betrieb des Gerätes kommt es zu Wärmeentwicklungen. Wenn Sie das
Gerät in einem Rack eingebaut haben, sollte während des Betriebes die Zufuhr von
Kühlluft stets gewährleitstet sein. Arbeiten Sie nie bei geschlossenem Rack. Bei
mehreren Rackgeräten sollten diese mit einem geringen abstand voneinander eingebaut
werden. Stapeln Sie dieses Gerät nicht zwischen Geräten mit hoher Wärmeentwicklung.
15. Dieses Produkt kann in Verbindung mit einem Verstärker und Kopfhörern oder
Lautsprechern Lautstärkepegel erzeugen, die anhaltende Gehörschäden verursachen.
Betreiben Sie es nicht über längere Zeit mit hoher Lautstärke oder einem Pegel, der Ihnen
unangenehm is. Wenn Sie ein Nachlassen des Gehörs oder ein Klingeln in den Ohren
feststellen, sollten Sie einen Ohrenarzt aufsuchen.
x
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Sa fe t y No t ice s
INFORM ATION TO THE USER FOR CLASS A DIGITAL
DEVICE (FCC P ART 15, CLASS A)
This equipment has been tested and found to comply with the limits for a class A digital
device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause interference to radio
communications. Operation of this equipment in a residential area is likely to cause
interference in which case the user will be required to correct the interference at his own
expense.
The user is cautioned that changes and modifications made to the equipment without the
approval of manufacturer could void the user’s authority to operate this equipment.
Use only shielded and grounded cables with this equipment to ensure compliance with FCC
Rules.
INDUSTRY CANADA (DIGITAL AP P ARATUS)
INT ERFERENCE-CAUSING EQUIP M ENT STANDARD
ICES-0 0 3 ISSUE 2
This Class A digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Sa fe t y No t ice s
CE DECLARATION OF CONFORM ITY
Manufacturer’s Name:
Alesis Corporation
Manufacturer’s Address:
1633 26th Street
Santa Monica, CA 90404
USA
declares, that the product:
Product Name:
Product Type:
M20
Modular Digital Multitrack Recorder
conforms to the following Standards:
Application of Council Directive:
Safety:
89/ 336/ EEC; 73/ 23/ EEC
EN 60 065
(1993) First Edition, Amendment No.1 (1994)
EMC:
EN 55022:1988 Class A
IEC 801-2:1991 2nd Edition, 4kV direct,
8kV air
IEC 801-3:1984 2; 3V/ m 150MHz-1GHz
IEC 801-4:1988 1st Edition 2; 1kV, 0.5kV
All tests were performed with fully-shielded
cabling.
European Contact:
Sound Technology
17 Letchworth Point, Lechworth,
Hertfordshire, SG6 1ND, England.
Phone: +44.1462.480000
Fax: +44.1462.480800
April, 1998
xii
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAP TER 1
OVERVIEW , SET UP , AND
BASICS
The Alesis M20 is an 8-track digital tape recorder that records on S-VHS videotape
cassettes. It is compatible with the ADAT format used with several other digital recorders
(Alesis ADAT, ADAT XT, LX20, and XT20; Studer V-Eight; Fostex RD-8 and CX-8; and
Panasonic MDA-1).
1.1 M 20 HIGHLIGHTS
·
Direct-drive full-servo S-VHS transport, designed for continuous shuttling and heavy-
duty professional use
·
Two available bit resolutions: 16-bit standard ADAT Type I, and 20-bit ADAT Type II
·
·
·
·
·
·
·
·
·
·
·
·
24-bit A/ D and D/ A converters
+4 dBu balanced XLR and ELCO (multipin) connectors
Selectable 16-bit dithered output for transfer to 16-bit systems
Jog/ shuttle wheel for fast navigation
Analog Aux track for superb scrub and jog monitoring
ADAT , SMPTE, video and word clock synchronization capabilities
Dedicated SMPTE time code track
Optional EC-1 8 channel AES/ EBU digital audio interface
Two custom vacuum fluorescent displays
Extensive error reporting capability
Optional CADI remote control
Optional RMD remote meter display
ALESIS M 20 REFERENCE M ANUAL 1.0 6
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Ove r vie w , Se t u p a n d Ba s ics , Ch a p t e r 1
1.2 UNP ACKING AND INSP ECTION
Please retain the M20’s shipping carton, which is designed to protect the unit during
shipping, in the unlikely event that you need to return the M20 for servicing. Some carriers
have restrictions on shipping electronic equipment without the original packing.
The shipping carton contains:
§
§
§
§
§
§
§
M20 with the same serial number shown on shipping carton
Power Cable
Optical Cable
M20 LRC (remote control unit)
This instruction manual
Blank S-VHS ST-120 cassette
Alesis warranty card
In order to be advised of future updates, please register your purchase immediately by
filling out the warranty card and mailing it back to Alesis.
1.3 AC P OW ER HOOKUP
1
Make sure the M20 is turned off. It’s good practice not to turn on the M20 until all other
cables are hooked up.
2
Before plugging in to AC power, note that the M20’s IEC-spec AC cord (do not
substitute any other AC cord) must feed a 3-pin outlet, where the third, round pin
connects to ground. The ground connection is an important safety feature designed to
keep the chassis of electronic devices at ground potential. Unfortunately, the presence
of a third ground pin does not always indicate a properly grounded outlet; check this
with an AC line tester. If the outlet is not grounded, consult with a licensed electrician.
3
Plug the power cord’s female end into the M20’s power input socket, and the male
(plug) end into any AC power source from 90 to 250 volts, 50 or 60 Hz.
Your M20 includes the correct power cord for your country or local area. When using an
M20 abroad , use only the following alternative power cords approved for use with ADAT:
·
For 90-120 VAC 50/ 60 Hz operation in the US, Canada and/ or Japan, use Alesis
UL/ CSA power cord #7-41-0001.
·
·
For 240 VAC 50 Hz operation in England, use Alesis UK power cord #7-41-0004.
For 220 VAC 50 Hz operation in Europe and Scandinavia, use Alesis EU power
cord #7-41-0002.
·
For 240 VAC 50 Hz operation in Australia, use Alesis AS power cord #7-41-0003.
1-2
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 1, Ove r vie w , Se t u p a n d Ba s ics
Alesis cannot be responsible for problems caused by using the M20 or any
associated equipment w ith improper AC w iring.
1.4 LINE CONDITIONERS AND P ROTECTORS
Although the M20 tolerates typical voltage variations, the AC line voltage may contain
spikes or transients that can possibly stress your gear and, over time, cause a failure. There
are three main ways to protect against this, listed in ascending order of cost and
complexity:
·
Line spike/surge protectors. Relatively inexpensive, these help protect against strong
surges and spikes (they usually need to be replaced after enduring an extremely strong
spike).
·
·
Line filters. These generally combine spike/ surge protection with filters that remove
some line noise (dimmer hash, transients from other appliances, etc.).
Uninterruptible power supply (UPS). This is the best option. A UPS provides power
even if the AC power line fails completely. Intended for computer applications, a UPS
allows an orderly shutdown in the event of a power outage. Furthermore, the isolation
it provides from the power line minimizes all forms of interference ó spikes, noise, etc.
1.5 ABOUT AUDIO CABLES
The connections between the M20 and your studio are your music’s lifeline. Use only high
quality, low-capacitance, shielded cables with a stranded (not solid) internal conductor and
low-resistance shield. Although quality cables cost more, they make a difference. When
routing cables:
·
·
Do not bundle audio cables with AC power cords.
Avoid running audio cables near sources of electromagnetic interference such as
transformers, monitors, computers, etc.
·
Do not place cables where they can be stepped on. Stepping on a cable may not cause
immediate damage, but it can compress the insulation between the center conductor
and shield (degrading performance) or reduce the cable’s reliability.
·
·
Avoid twisting the cable or making sharp, right angle turns.
Never unplug a cable by pulling on the wire itself. Always unplug by firmly grasping
the plug’s body, and pulling directly outward.
·
Although Alesis does not endorse any specific product, chemicals such as Tweek and
Cramolin, when applied to electrical connectors, are claimed to improve the electrical
contact between connectors.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Ove r vie w , Se t u p a n d Ba s ics , Ch a p t e r 1
1.6 BASIC AUDIO HOOKUP
When connecting audio cables and/ or turning power on and off, turn off all devices in
your system and turn down your monitor system’s volume controls.
The M20 provides 10 pairs of XLR connectors (8 pairs for audio in/ out, 1 pair for the
auxiliary analog channel, and 1 pair above for SMPTE time code). The nine sets of audio
XLRs connect to your mixer’s tape or line inputs and outputs. An additional multipin
ELCO connector , wired in parallel with the 8 XLR audio pairs, can connect to a “snake”
that goes to your mixer. Several manufacturers make ADAT/ M20-specific cables that break
out the ELCO connector into individual ins and outs.
1.7 USE T HE RIGHT TAP E
Use only premium quality, name brand S-VHS cassettes such as Quantegy 489 DM Digital
Mastering Audio Tape, or Alesis ADAT Mastering Audio Cassettes. Other acceptable brands
include Maxell XR-S Black, JVC XZ, Sony DASV, BASF Digital Master 938, Apogee AA-40,
HHB ADAT45, and TDK SP Super Pro. The cassette shell, hubs, rollers and tape guides in S-
VHS cassettes are precision devices that properly handle and protect the tape within them.
Caution: Do not use VHS cassettes. While they may appear to function properly at
first, their less-than-premium formulation w ill decrease the reliability of
your recording. They may also shed oxide and leave behind a coating of
dirt that w ill interfere w ith future recordings, even if you sw itch back to
premium quality tape. Defective tape may even clog the head, requiring
service. Trust your w ork only to premium quality S-VHS tape.
1.8 P REP ARING THE TAP E P RIOR TO USE
Fast forward and rewind all new tapes at least once from end to end before attempting to
format and record on them. This important step “unpacks” the tape properly, and leads to
far more reliable operation (this is also recommended practice for DAT tapes).
1.9 EJECT TAP E P ROP ERLY
After a session, eject the tape and put it in a protective case. Do not:
·
·
·
Leave the tape in the M20 when power is off.
Leave the tape halfway ejected in the well. Always remove completely after ejection.
Eject in the middle of recorded material. Malfunctions that could possibly damage the
tape are statistically most likely to occur when inserting or ejecting a tape, so always
eject where nothing is recorded.
1.10 BACKUP
Accidents can happen ó so, like computer floppy disks and hard disks, back up your M20
tapes to another M20 or ADAT using the fiber optic digital connector (see Tutorial 2 for
step-by-step instructions on backing up M20 tapes).
1-4
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 1, Ove r vie w , Se t u p a n d Ba s ics
1.11 OP ERATING ENVIRONM ENT
Mount the M20 in an equipment rack (requires 4 rack spaces) or place it on a table or shelf.
Alesis advises against tilting the recorder; keep it horizontal. Also remember that heat
shortens the life of electronic equipment.
Please observe the following:
·
The M20 is designed to perform properly over a range of ambient temperatures from
10° C to +40° C (50° F to 104° F), in up to 80% non-condensing humidity. These are not
absolute limits, but Alesis cannot guarantee that the M20 will meet its published specs
or remain reliable if operated outside of these ranges.
·
·
Always allow adequate ventilation behind the M20. Do not seal any enclosure that
holds the M20. It is not necessary to leave an empty rack space above or below the
M20.
You will need to remove the screw-on feet from the bottom of the M20 if any
equipment will be mounted directly below it.
1.12 AVOID ELECTROM AGNETIC INT ERFERENCE
Like all tape machines, the M20 uses magnetic tape that can be sensitive to electromagnetic
interference. Generally this is not a problem, but avoid mounting the M20 next to devices
that generate strong magnetic fields such as power amplifiers, monitors and video display
devices, speakers, etc., and always treat your tapes with care. In particular, avoid excess
heat, cold, and humidity.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Ove r vie w , Se t u p a n d Ba s ics , Ch a p t e r 1
Figure 1 (M20 Front Panel)
1-6
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAP TER 2
CONT ROL AND CONNECT OR
BASICS
2.1 ABOUT THE FRONT P ANEL
Referring to Fig. 1, the front panel includes:
·
·
S-VHS cassette door and Eject button
Main vacuum fluorescent display (toward the center) with two sets of 10-character 7-
segment readouts. The left readout shows the current tape location. The right readout
shows information such as incoming SMPTE time, locate address, current offset, etc. A
24-character alphanumeric display above the 7-segment display shows edit location
points, pre/ post-roll times, pitch value, and various messages.
·
·
·
·
·
·
·
·
9 function buttons (below the main display)
5 transport buttons
4 locate-related buttons
Rehearse button
Jog/ shuttle wheel and search button
15-button numeric keypad for data entry
15 editing switches
Secondary vacuum fluorescent display with VU meters for the 8 audio channels and
auxiliary track, the time code track signal, error lights, track input and record lights, and
input selection and routing indicators.
·
·
·
·
22 track enable and track record buttons
6 routing, source selection, and metering buttons
Online/ offline button
Recessed power switch
ALESIS M 20 REFERENCE M ANUAL 1.0 6
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Co n t r o l a n d Co n n e ct o r Ba s ics , Ch a p t e r 2
Figure 2 (M20 Rear Panel with optional EC-1 AES/ EBU Card)
2-2
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 2, Co n t r o l a n d Co n n e ct o r Ba s ics
2.2 ABOUT THE REAR P ANEL
Referring to Fig. 2, the rear panel includes:
2.2A P UNCH FOOT SW IT CH
This allows foot-controlled punch in and out. Use a momentary footswitch, either normally-
open or normally-closed (the M20 senses the type on power-up and calibrates itself).
2.2B LOCATE/P LAY OR LRC REM OTE CONT ROL JACK
This 1/ 4” jack accepts a momentary footswitch (normally closed or open) to allow foot-
controlled location functions. It also accepts the LRC remote control (see Chapter 14) for
remote access of transport functions.
Note: If using a normally open footswitch, the footswitch and LRC remote control can be
interchanged, or used simultaneously with a Y-cord, without restarting (powering
down and powering up) the M20. However, if using a normally closed footswitch,
the M20 unit should be restarted after switching from footswitch to remote control
and vice-versa.
2.2C ANALOG INP UT S AND OUT P UT S
18 XLR connectors carry the +4 dBu balanced analog inputs and outputs. There are 9 audio
input and output channels (channels 1 through 8 plus Aux). Channels 1 through 8 inputs and
outputs are also accessible through a multi-pin ELCO connector, which is wired in parallel
with the XLR inputs and outputs. All XLR connectors are wired with pin 2 “hot,” in
accordance with IEC standards.
2.2D TIM E CODE IN AND OUT
The time code input and output use balanced XLR connectors for use with SMPTE/ EBU
standard time code systems. Time code input allows the M20 to be slaved to an external
device; time code output provides timing reference to an external device.
2.2E W ORD CLOCK IN AND OUT
These are BNC connector, TTL-level word clock inputs and outputs. A master word clock
signal, which the M20 can provide, allows synchronizing the audio data stream for all digital
audio devices in a system. If a master word clock signal already exists, the M20 can sync to
it.
2.2F ADAT OP T ICAL IN AND OUT
The optical input and output are an industry-standard digital audio interface, pioneered by
Alesis, that carries 8 digital audio channels (with up to 24 bits of resolution) on a single fiber
optic cable. The standard cable is a 1mm diameter plastic fiber with Toslink connectors. One
1-meter cable is provided with the M20; additional cables of different lengths are available
from your dealer. Applications include digitally dubbing from one deck to another,
interfacing with hard disk recording systems and synthesizers, and feeding translators that
change the ADAT optical format to other formats.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Co n t r o l a n d Co n n e ct o r Ba s ics , Ch a p t e r 2
2.2G VIDEO IN AND THRU
The BNC connector video input (with 75 ohm termination switch) accepts composite video
as well as black burst video inputs.
2.2H ADAT SYNC IN AND OUT
These 9-pin D connectors synchronize multiple ADATs together to single-sample accuracy.
Computer interface cards with ADAT sync, such as the Alesis ADAT-PCR, allow
transferring ADAT data to and from a computer for editing with single-sample accuracy.
Interface cards without ADAT sync allow transferring ADAT data with 1/ 4 frame accuracy
via MIDI Time Code.
2.2I M IDI IN AND OUT
These 5-pin DIN connectors can output and/ or receive MIDI Machine Control commands,
save and load sysex dumps defining the M20 status, allow for software updates via MIDI
sysex files, and output MTC (MIDI Time Code) when selected.
2.2J RS-4 22 IN (SONY 9 -P IN)
This 9-pin D connector connects to a video editor or other controller that supports the Sony
9-pin protocol. This feature will not be operational until M20 Version 2.0 software becomes
available.
2.2K M ETER BRIDGE/REM OTE P ANEL OUT
This RJ-45 connector connects to an optional remote controller like the Alesis CADI remote,
and/ or RMD meter bridge.
2.2L P OW ER
The IEC-standard, grounded AC input plug accepts AC voltages from 90 to 250 volts,
eliminating the need for transformers or voltage switches.
2-4
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAP TER 3
EDITING M 20 OP ERAT ING
P ARAM ET ERS
3.1 THE KEYP AD
The keypad block contains switches for editing the various parameters that control the M20’s
features.
3.1A 0 T HROUGH 9 BUT T ONS
Use the 10 numeric keys to enter number parameter values and letters for names. When
editing a parameter value, pressing a key enters its associated number. When editing a name,
pressing a key cycles through the letters indicated on the keycap (e.g., pressing 7 repeatedly
cycles through 7, s, t, u, v, 7, s, t…etc.).
3.1B UP ARROW /YES/UP P ER CASE
This key:
·
Increments parameter values, as well as scrolls up through a list of parameter values.
Holding this button for 2 or more seconds increases the speed at which the values
increment. After 7 seconds, this speed increases again.
·
·
·
Enters “Yes” in response to Yes/ No queries.
In a sign (polarity) field, selects the positive (+) sign.
In a name field, changes lower case letters to UPPER CASE.
3.1C DOW N ARROW /NO/LOW ER CASE
This key:
·
Decrements parameter values, as well as scrolls down through a list of parameter values.
Holding this button for 2 or more seconds increases the speed at which the values
decrement. After 7 seconds, this speed increases again.
·
·
·
Enters “No” in response to Yes/ No queries.
In a sign (polarity) field, selects the negative (-) sign.
In a name field, changes UPPER CASE letters to lower case.
3.1D CURSOR LEFT
When editing, this key positions the cursor (a single underline character, showing that a
parameter is ready for editing) under the next field to the left. (Note: It will not move across
page boundaries.)
3.1E CURSOR RIGHT
When editing, this key positions the cursor (a single underline character) under the next field
to the right. (Note: It will not move across page boundaries.)
ALESIS M 20 REFERENCE M ANUAL 1.0 6
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Ed it in g M 20 P a r a m e t e r s , Ch a p t e r 3
3.1F ENT ER/NAM E
This key has two main uses:
·
·
Speed up numeric entry by eliminating the need for “leading zeroes.” For example, the
varispeed setting is a 3-digit value. Instead of having to key in something like 0 - 0 - 9,
you can simply key in 9, then press Enter.
Edit location point names. When the locate time is the currently selected field, pressing
the Enter/ Name button positions the cursor at the first character of the name. The cursor
buttons now select individual characters within the name field or other displayed fields;
use the keypad buttons to change the character. For upper case, use the Up Arrow. For
lower case, use the Down Arrow.
To exit the name field, press the Enter/ Name button again.
Using the default name list instead of entering letters individually: An additional
name editing option is available. Holding down the Name button while using the
Up/ Down buttons scrolls through a default set of 16 generic names (e.g., Verse 1,
Chorus, Bridge, etc.). This list may be customized for your working style.
To customize the default set of names:
1
2
3
Select the default name to be changed.
Edit it.
To store the new name in the default name list, hold the Enter/ Name button and press
the Record button.
3-2
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 3, Ed it in g M 20 P a r a m e t e r s
3.1G SELECTING P AGES
Most buttons have at least one associated display page, which contains one or more
parameters. If there are multiple pages, the main display’s left side shows the current page
number; repeatedly pressing the associated button cycles through the pages.
Shortcut: To access a particular page directly, hold the associated button and use the keypad to enter
the desired single-digit page number.
Functions with double-digit page numbers (e.g., the Utility function) have a different access
procedure. Hold the current function button and press the 2 digits within 3 seconds of each
other. To select a single digit page number (1 through 9), press and hold the current function
button and either:
·
·
Enter 0, then the digit; or
Press the single digit, then the Enter button. (Note: If the Enter button is not pressed
within 3 seconds, the display reverts to its previous state.)
3.1H SELECTING P AGE P ARAM ET ERS
To select the desired parameter for editing in multi-parameter pages, position the cursor
with the Left or Right Cursor button under the parameter value’s rightmost digit.
3.1I ENT ERING P ARAM ET ER VALUES
Entering complete values: Use the numeric keypad and enter the most significant digit first.
Enter all of a field’s digits to complete the entry. The cursor automatically advances through
the fields.
Increment/decrement a value by one: Use the keypad’s Up and Down buttons. Holding the Up
or Down button for more than 2 seconds increments (or decrements) the value continuously.
The value above the cursor will be changed. If the value goes beyond a boundary (for
example, increasing from 59 seconds to 0), the next field will be calculated automatically (in
this example, the minute field will be automatically increased).
ALESIS M 20 REFERENCE M ANUAL 1.0 6
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Ed it in g M 20 P a r a m e t e r s , Ch a p t e r 3
3.2 THE EDIT BUTTON
The Edit button toggles the M20 in and out of Edit Mode. Enabling Edit mode (button lit)
allows editing parameter values for the functions grouped with the Edit button: Track Delay,
Tape Offset, SMPTE Chase, Internal Gen, Format, Pre-Roll, Post-Roll, Auto Return, and Auto
Record. While Edit is On, only the currently selected function’s switch will light. However,
the M20 retains the current on/ off status of all switches, and these become visible after
exiting Edit mode.
Note: Don’t be confused! Editing a function does not turn it on. For example, while
editing the Post Roll value the Post Roll switch will be lit, but if the light goes out
when you leave Edit mode, Post Roll is not yet active.
If the Edit LED is not lit, pressing the various switches toggles these functions on and off.
Example: If you’ve used the Edit button to edit the amount of Tape Offset and the Edit button
is off, turning on the Tape Offset button enables the programmed amount of offset.
Pressing the Display, Pitch Value, or Utility button will also exit Edit mode and enter the
Display, Pitch, or Utility pages, respectively.
3.3 EDITING CONVENTIONS
·
The rightmost 7-segment display shows locate times in hours, minutes, seconds, frames,
subframes and samples. Subframes equal 1/ 100th of a frame and range from 0…99. The
number of samples per subframe depends on the Tape Counter and Sample Rate settings.
If the tape counter is in ABS Time mode, there are always 15 samples per subframe in 48
kHz and 14 per subframe at 44.1 kHz. If the counter is in a SMPTE Time Code mode and
the sample rate is 48 kHz, Sample steps range from 0 - 15 for 30 frames/ sec, 0 - 15 or 16 for
29.97 frames/ sec, 0 - 18 for 25 frames/ sec, and 0 - 19 for 24 frames/ sec.
·
A lit arrow above the subframe (SF) indicator indicates that there is a non-zero sample
value. To access the samples field, with the subframe field selected press the Right
Cursor button. This selects a second page that shows only the sample value.
·
·
·
When editing any tape address, the cursor steps in fields (hours, minutes, seconds,
frames, subframes, and samples) instead of stepping every digit.
When editing any tape address, entering digits with the keypad automatically advances
the cursor or selected field (using the Up/ Down Arrows does not advance the field)
When editing a field in the 7-segment display, the digit(s) of the selected (and currently
editable) field will flash.
3-4
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAP TER 4
TAP E FORM ATTING
Formatting is essential to the ADAT system. It creates a sample-accurate time reference (i.e.,
it’s accurate to 1/ 48,000th of a second when recording at 48 kHz) on each tape, in addition to
block ID codes, linear control track, and other essential markers. This provides tight
synchronization ó far better than SMPTE sync ó between ADAT-compatible devices, as well
as precision tape counter readings and intelligent autolocation functions.
The format process first records 15 seconds of leader (the display shows LEAd), followed by
two minutes of data (the display shows dAtA), then ABS time code starting at 00:00:00.00
and continuing to the end of the tape.
Caution: formatting a tape erases all material on all tracks. Always check that the tape is either blank
or contains unwanted material before formatting.
You can either:
·
·
·
Format a tape completely before recording (recommended)
Format while you are recording, for as long as needed
Extend the format of an incompletely formatted tape
Before formatting a blank tape, you must select:
·
·
The sample rate (44.1 or 48 kHz)
The word length (20-bit for Type II tapes, or 16-bit for compatibility with Type I
ADAT and ADAT-XT tapes)
ALESIS M 20 REFERENCE M ANUAL 1.0 6
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Fo r m a t t in g Ta p e , Ch a p t e r 4
4 .1 SAM P LE RATE SELECTION
Choose between 44.1 kHz (CD/ consumer standard) or 48 kHz (DAT/ professional standard).
Here are some general hints:
·
·
·
If mixing the tape through a digital mixer for a CD master, use 44.1 kHz to avoid sample
rate conversion.
If mixing the tape through an analog mixer, use 48 kHz for slightly better high frequency
response.
If you plan to transfer M20 tracks over to a hard disk system for editing, note that audio
recorded at 48 kHz requires about 10% more storage capacity than the equivalent audio
recorded at 44.1 kHz.
The following sample rate selection procedure assumes that Clock Source is set to INTernal.
Operation
Select sample rate
You press…
Sample Rate
button
You see…
Sample Rate block toggles between 44.1
or 48 kHz (default) with each Sample
Rate button press
About changing sample rates: The sample rate chosen during the format process does
not have to be used during playback or recording of that particular tape; the ADAT
format always allows you to override the default sample rate from the tape. When
loading a formatted tape, the sample rate will automatically switch to the tape’s
original settings. You may change the sample rate setting to playback or record with
a different sample rate, but the sample rate indicator will flash to indicate that it is
not at the original setting. Changing the sample rate directly affects the pitch and
speed of any audio recorded.
When extending a format, the sample rate will automatically assume the existing
format’s values. There is no way to format a tape with a “44.1” marker on one
section and a “48” marker on another.
4-2
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 4 , Fo r m a t t in g Ta p e
4 .1A P ULL-UP AND P ULL-DOW N SAM P LE RATE SELECTION
The Sample Rate button is also used to select the respective 0.1% pull-up and pull-down
rates. A pull-up is available with a 30 fps SMPTE rate only. A pull-down is available with a
29.97 fps SMPTE rate only.
Use pull-up or pull-down after a standard tape format: It is not necessary to pre-select
a pull-up or pull-down prior to formatting since the “pull” status is not recalled
when tapes are subsequently reinserted. Use the pull-up/ pull-down feature after
formatting your tape. If you are formatting and recording simultaneously, using the
pull-up/ pull-down feature may be appropriate.
Operation
Select a Pull-up
sample rate
You press…
…and hold
Sample Rate
button then press
Up button
You see…
“+0.1%” displayed in the Sample Rate
block
Select a Pull-down
sample rate
…and hold
“- 0.1%” displayed in the Sample Rate
block
Sample Rate
button then press
Down button
…and hold
Sample Rate
button then press
the 0/ Space
button
Return to a normal
44.1/ 48 kHz sample
rate from a “pulled”
rate
Sample Rate block returns to normal
sample rate display (44.1 or 48 kHz)
Refer to section 16.4 for more information on pull-up and pull-down.
4 .2 W ORD LENGTH SELECTION
Select 20 bits unless you want compatibility with older, Type I format ADAT tapes.
Operation
You press…
You see…
Initiate word length
selection
Select word length
Edit button, then
Format button
Up or Down
Display says “Format Data Type” and
16 or 20 bits
The desired word length (16 or 20)
Arrow button so
that the display
shows…
ALESIS M 20 REFERENCE M ANUAL 1.0 6
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Fo r m a t t in g Ta p e , Ch a p t e r 4
4 .3 FORM AT A NEW TAP E
Use only S-VHS blank tapes formulated specifically for Super VHS video or digital audio
applications. Never use standard VHS tapes.
“Exercise” the tape: Before formatting, fast forward the tape to the end and rewind it to
even out the tape pack and sweep any contaminants off the tape.
Operation
Insert blank tape
You press…
Tape into tape
chamber. Do this
gently; the
You see…
Display shows “noFO,” Format button
flashes
machine will
“grab” the tape
Format button
(with Edit button
off)
Enable formatting
Initiate formatting
All record lights turn on
Hold Record
then press Play
Display message advises you of
formatting progress
What happens between initiating formatting and the actual process of formatting depends on
the current tape status.
Tape status
The M20…
Unformatted, at start of tape
Unformatted, partway through tape
While rewinding from current position,
goes from unformatted to previously
formatted portion
Begins formatting immediately
Rewinds, then begins formatting
Disables formatting to avoid re-
formatting a partially formatted tape.
Either extend the format from this
point on, or for a complete format,
rewind, then initiate formatting
Rewinds, then begins formatting
Formatted, in Leader or Data section of
tape
Formatted, in Audio section of tape
Extends format after entering record
(see section 4.5 for information on
extending a format)
4 .4 RECORD TRACKS W HILE FORM ATTING
The procedure is similar to standard formatting, except:
·
·
Record-enable (section 5.4) any tracks to be recorded prior to pressing the Format button.
No audio will be recorded before the counter shows 00:00:00.00 ABS time.
4-4
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 4 , Fo r m a t t in g Ta p e
4 .5 EXTEND A P ARTIALLY-FORM ATTED TAP E
·
·
The procedure is similar to standard formatting, except:
Make sure the tape is located at least 20 seconds before the end of a previously-formatted
section before attempting to extend the format.
·
·
Regardless of the current sample rate and word length, these will change automatically
to match the original format.
After pressing the Format button, press and hold Play then press Record. Formatting
will begin when a lock is established.
Note: The above assumes the tape is somewhere after ABS time 00:00:00.00. If the tape to
be extended is in the leader or data sections (i.e., prior to ABS time 0:00:00.00),
entering Format mode automatically rewinds the tape to the leader and begins
reformatting. While rewinding, the display shows “…format begun” and the Rewind
button will light to remind you that the M20 must format over from the tape’s leader
and data sections.
4 .6 END FORM ATTING
When the tape reaches the end, formatting ends automatically and the tape will stop.
To stop formatting prior to the end-of-tape, press Stop. You cannot simply punch out with
the Play button.
4 .7 CERTIFY TAP E FORM AT
After formatting, consider playing the tape through to the end to check for a suitably low
error count (see section 13.20), thus verifying the tape’s integrity.
4 .8 REFORM ATTING: CAUTION!
Do not stop in the middle of re-formatting over a previously formatted tape. When the tape
transitions from the newly formatted section to the previously formatted section, there will
be timing discontinuities, and you will not be able to record anything over the transition.
Either re-format the entire tape from beginning to end, or rewind a bit and extend the
existing format.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Fo r m a t t in g Ta p e , Ch a p t e r 4
4 .9 LOCK OUT FORM ATTING (SAFE M ODE)
You may lock out the format option to prevent accidental formatting. This remains in effect,
even if you insert different tapes, until the setting is changed. To lock out formatting:
Operation
You press…
You see…
Select safe function
Edit button, then
Format button
until display
Display says “Format Safe:” and
format safe status (on or off)
shows Page 2
(Format Safe)
Up or Down
Arrow button to
choose On or Off
respectively
Select format safe
status
Selected format safe status
4 .10 BULK ERASING
You can bulk-erase M20 tapes with a video tape eraser.
4 .11 RECORDING A “BENCHM ARK” T AP E
Alesis recommends that you format and record a new tape with any signal, such as a test
tone, in a single pass with no overdubs during the first week of operation. Store this tape in
a safe, dry location and don’t use it for any other purpose. Such a “benchmark” tape is useful
to determine if the error correction rate is increasing over time because the heads need to be
cleaned, or if a tape is defective.
4-6
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAP TER 5
TRACK RECORD ENABLING AND
M ONIT ORING
5.1 TRACK BASICS
The M20 can record a total of 10 tracks:
·
·
8 digital audio tracks. These record standard audio signals, either from the analog
inputs, optional AES/ EBU card, or ADAT Optical Interface.
1 analog Aux track. This track records audio information from the Aux input, along with
any of the eight audio tracks routed to the Aux track. This provides quality scrubbing
(which is difficult to do solely in the digital domain) and the ability to hear audio from
the Aux output during rewind, fast forward, and autolocate operations. During Search
operations, the Aux track can be routed to any of the eight standard audio track outputs
(see section 6.5).
·
1 time code track. This track records only SMPTE/ EBU time code information, and
stores this data digitally on tape. It receives its input from the Time Code In jack if the
TC Source is set to External (section 11.3), or from the Internal Time Code Generator if
the TC Source is set to Internal.
SMPTE vs. ABS time code: The ADAT ABS time reference is separate from this SMPTE
time code track, and is written in a subcode of the tape automatically as part of the
format operation covered in Chapter 4.
To record, a track must first be record-enabled (see section 5.4; the record enable button light
will flash).
Aux and TC track record enabling: The Aux and TC tracks cannot be record enabled
simultaneously. For example, if the Aux track is record enabled and the TC Track
record enable button is pressed, record will disable on the Aux track and the TC
Track will become record enabled. This will occur in any transport mode, so if a
record is in progress on the TC Track, pressing the Aux track record enable button
will punch-out of the TC Track.
You typically press the Play and Record transport buttons to allow track-enabled tracks to
begin recording, although you can also use a footswitch (section 8.6e) and/ or program
automatic punch in points (sections 8.8a and 8.8c). During recording, any armed Record
Enable buttons stay lit steadily.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
T r a ck Re co r d En a b lin g a n d M o n it o r in g , Ch a p t e r 5
5.2 TRACK INP UT ENABLES
An input-enabled track monitors the associated input signal. There is one Input Enable
button (with associated indicator light) for each track (10 total). The Input Enable button
toggles between monitoring the input signal or monitoring the tape.
Operation
You press…
You see…
Enable track input
(monitors input signal)
Disable track input
(monitors tape signal)
The track Input Enable
button until…
The track Input Enable
button until…
Track input light turns
on
Track input light turns
off
5.3 AUTO INP UT SW ITCH
This switch determines whether or not a record-enabled track (audio or aux) will monitor
from input or tape automatically, depending on the recording context. Disabling Auto Input
is preferred for recording basic tracks, while Auto Input is usually enabled during
overdubbing and punching.
What the tracks
monitor
Auto Input
Off
Auto Input On
Record-enabled
tracks monitor the…
Non-record-enabled
tracks monitor the…
Input signal
Input while recording or stopped, tape
while playing
Tape while playing or recording, input
signal when stopped
Tape
5.4 RECORD ENABLE
Pressing a track’s Record Enable button allows it to record when the M20 is in Record mode.
Any number of channels can punch in simultaneously, or punch out simultaneously, and any
channel or channels can punch in or out while other channels are in record.
Operation
You press…
You see…
Record enable a track
The track Record Enable
button
The Record Enable light
flashes, then lights solid
while recording
Turn off record enable
for a track
The track Record Enable
button
The Record Enable light
turns off
Punch in using Record
Enable button
While in Record mode
and the tape is running,
press Record Enable
button
Record Enable button
lights solid
Punch out using Record
Enable button
While recording, press
Record Enable button
Record Enable button
turns off
If you press Play and Record with no tracks record-enabled, the Record light will flash
indicating a Record Pending mode. When the Record light is lit (or flashing if Rehearse is
enabled; see section 8.7), pressing individual track Record Enable buttons can punch
individual tracks in or out independently. The Record light will remain lit (or flashing in
Rehearse mode) until you punch out of Record, usually by pressing Play or any other
transport key.
5-2
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 5, T r a ck Re co r d En a b lin g a n d M o n it o r in g
5.5 SAFETY M ODE (ALL SAFE)
To prevent any accidental recording, pressing All Safe places all tracks (channels 1-8 plus
Aux and TC) into a safe (non-record ready) mode. This is particularly useful when mixing.
Operation
You press…
You see…
Place all tracks into a safe
(non-recordable) mode
All Safe
All track record ready
lights and auto-enabled
track input lights turn off
All track record ready
lights, and auto-enabled
track input lights return
to their state prior to
pressing All Safe
Exit safe mode
All Safe
5.6 M ONITOR INP UTS (ALL INP UT)
Pressing All Input sets all tracks, excluding the TC track, to monitor the input signal
regardless of the record-ready/ auto-input status (section 5.3). Tape playback cannot be
heard while All Input is on. While enabled, the track input buttons will have no effect. This
is useful for live recording situations.
Operation
You press…
You see…
Have all tracks (except
TC) monitor the input
signal
All Input
All Input Enable lights
(except TC) are lit solid
Exit All Input mode
All Input
All Input Enable lights
return to their state prior
to pressing All Input
This function can also be used while All Safe is on.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
T r a ck Re co r d En a b lin g a n d M o n it o r in g , Ch a p t e r 5
5-4
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAP TER 6
DIGITAL/ANALOG INP UT
SELECT ION AND ROUT ING
6 .1 DIGITAL SOURCE
When using digital inputs, this function selects one of two or three digital input options. The
I/ O card option will appear in the display only if an I/ O card (such as the Alesis AES/ EBU
card) is installed in the machine. Settings are retained in memory.
Operation
You press…
You see…
Select ADAT optical
digital input (default)
Select digital track copy
function
The Digital Source button
until you see…
The Digital Source button
until you see…
ADAT optical in the Dig
Source block
Track Copy in the Dig
Source block
Select I/ O card as the
digital input
The Digital Source button
until you see…
I/ O card in the Dig
Source block
For more information on Track Copy, see section 6.4b.
6 .2 INP UT SELECT
Not valid in Track Copy mode: If the Digital Source has been set to Track Copy, you
cannot enter Input Select mode. In Track Copy mode, only internal tape tracks may
be recorded.
Inputs can come from digital or analog signal sources. Use the Input Select button to choose
digital or analog inputs as the signal source for each adjacent track pair (1/ 2, 3/ 4, 5/ 6, or
7/ 8). In addition, all tracks may be set to receive analog or digital.
If no track buttons are pressed within 10 seconds of entering Input Select mode, the M20
automatically exits.
Operation
You press…
You see…
Enter Input Select mode
The Input Select button
Input Select display
indicator flashes
A and D indicators at the
base of the VU meters
indicate analog or digital
input, respectively
A and D indicators all
show D
Select analog or digital
input source
Either Track Input button
of a stereo pair to toggle
between analog or digital
source for the track pair
The All Input button
Select all channels for
digital input
Select all channels for
analog input (default)
Exit Input Select mode
The All Safe button
A and D indicators all
show A
Input Select indicator
turns off to confirm the
exit
The Input Select button
ALESIS M 20 REFERENCE M ANUAL 1.0 6
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
In p u t Se le ct io n a n d Ro u t in g , Ch a p t e r 6
If no digital signal input is detected, the D indicators for the channel(s) without a digital
signal source will flash until signal is detected.
6 .3 TRACK OUTP UT SELECTION
It is not necessary to select an output destination. Audio data always appears simultaneously
at the analog, ADAT optical, and optional AES/ EBU outputs. Audio always appears at the
same-numbered output it was recorded on.
6 .4 INP UT SIGNAL ROUTING (ANALOG AND DIGITAL)
The Input Route button selects how the M20’s analog and digital inputs are routed to the 8
tape channels. If no track buttons are pressed within 10 seconds of entering Input Route
Mode, the M20 automatically exits.
Operation
You press…
You see…
Enter Analog Routing
page (available only if at
least one track pair’s
input has been set to “A”
using Input Select mode)
Choose Analog Routing
The Input Routing button
Every track’s A indicator
lights, display says
“Select analog input trks”
Input (white button
below record) for Track 1
or 2 to select Odd/ Even,
Track 3 or 4 to select Half
& Half, Track 5, 6, 7, or 8
to select One-to-One
(default; see diagram
below)
Odd/ Even lights tracks 1
&2, Half & Half lights
tracks 1—4, One-to-One
lights tracks 1—8
Enter Digital Routing
page (available only if at
least one track pair’s
input has been set to “D”
using Input Select mode)
The Input Routing button
again (or press twice if
not already in Input
Route mode)
Every track whose Input
Select is set to Digital’s D
indicator lights, display
says “Select optical src
trks” or “Select I/ O card
src trks”
Choose Digital Routing
Exit Input Routing mode
See section 6.4b
See Section 6.4b
Press the Input Routing
button until the Input
Route indicator turns off
Channel indicators and
track select buttons
return to their normal
status
Analog and Digital Routing not available in Track Copy mode: If the Digital Source
has been set to Track Copy, Input Routing sets which internal tape tracks will be
copied (see 6.4b).
6-2
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 6 , In p u t Se le ct io n a n d Ro u t in g
6 .4 A ANALOG INP UT ROUT ING
The three analog routing modes accommodate 2, 4, or 8 bus mixing consoles. With two
buses, connect them to inputs 1 and 2. With four buses, connect them to inputs 1 through 4.
With 8 buses, direct outs or a patch bay, run each bus out to its like-numbered M20 input.
The analog routing choices are:
·
Odd/ Even: Press either the Track 1 or 2 button. Input 1 feeds channels 1, 3, 5, 7, and
Input 2 feeds channels 2, 4, 6, 8. To record on an odd-numbered track, route the
signal(s) to bus #1 or left. To record onto an even-numbered track, route the signal(s)
to bus #2 or right. By simply putting the desired track into record, the proper signal
will get there, even though it is not connected directly to the track’s input jack.
·
·
Half & Half: Press either the Track 3 or 4 button. Input 1 feeds channels 1, 5; input 2
feeds 2, 6; input 3 feeds 3, 7; input 4 feeds 4, 8). To record on tracks 1 or 5, route the
signal(s) to bus #1. Likewise, to record onto tracks 2 or 6, route the signal(s) to bus
#2, and so on.
One-to-one: Press either the Track 5, 6, 7, or 8 button in Input Routing mode. This is
the power-on default, where each input feeds its corresponding channel. To record
on track 1, send the signal to mixer bus 1, to record on track 2 send the signal to
mixer bus 2, etc. This is also the recommended mode when feeding the M20 from a
mixer channels’ direct outs.
Alternate method: In Input Routing mode for analog inputs, the All Safe button selects
the odd/ even configuration and the All Input button selects one-to-one.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
In p u t Se le ct io n a n d Ro u t in g , Ch a p t e r 6
6 .4 B DIGIT AL INP UT ROUT ING
The Digital Source setting (section 6.1) influences the digital input routing process. This
feature makes it possible to record incoming digital data on any track desired, without
manually repatching.
If digital source = ADAT Optical:
Any of the 8 incoming optical channels may be individually selected or de-selected with the
Track Input buttons while in Digital Routing mode.
·
·
·
·
A lit track input light indicates that the incoming ADAT optical channel is a digital
source.
If a track input light is dark, that means the incoming ADAT optical channel will be
skipped as a source.
Pressing the All Input button selects all eight channels as optical sources (this is the
normal state).
Pressing All Safe turns off all channels, which results in a one-to-one routing (just as
if all 8 channels were selected as sources). All Safe simply “clears the slate” for
additional digital source channel selections.
If digital source = I/O Card (AES/EBU):
Because AES/ EBU is a 2-channel digital format, only channel pairs (1-2, 1-4, or 1-8) may be
selected or de-selected. Pressing the All Input button selects all channels. As in ADAT
Optical, a lit track input light indicates that the channel is a digital source.
If digital source = Track Copy:
Any of the 8 channels, to a maximum of 4 total, may be individually selected or de-selected.
A lit track input light indicates that the channel is a track copy source, i.e., the selected
channels are the internal source channels eligible for digital bouncing within a single M20.
Pressing the All Input button selects channels 1 through 4 as track copy sources.
·
·
No more than 4 tracks may be copied within a single machine, so if 4 source tracks
are already selected, one must be de-selected before you can select another track.
A digital source track cannot be record-enabled in Track Copy mode. If you try, the
message “Source cannot equal dest” will appear in the display.
·
·
When copying tracks, any track delays (section 11.9) will be in effect.
Pressing All Safe deselects any track copy source channels.
6-4
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 6 , In p u t Se le ct io n a n d Ro u t in g
6 .4 C RECORD-ENABLING T HE DEST INAT ION TRACKS
In Digital Routing mode, inputs need not be routed only to same-numbered tracks. Any
selected digital source inputs can be re-routed to any record-enabled destination tape tracks,
in ascending order.
Example: if ADAT optical source inputs 1 and 5 are selected using Input Routing, and
tracks 3 and 4 have digital sources (“D” selected as Input Select) and are record-
enabled, then incoming digital audio on optical channel 1 goes to track 3, and
incoming digital audio on input 5 feeds track 4.
If more destination tracks are enabled than there are source inputs, the source inputs will
repeat (cycle). Note that this technique allows copying a single incoming signal to multiple
tracks.
Example: if in the previous example tracks 7 and 8 were record-enabled as well as tracks
3 and 4, audio from input 1 would go to tracks 3 and 7, and incoming audio from
input 5 would feed tracks 4 and 8.
If all 8 source tracks are selected, then no digital routing occurs as this gives a one-to-one
relationship (the power-on default).
Example: if all eight ADAT optical sources are selected, and tracks 3 and 4 are record-
enabled, they will receive digital audio from ADAT optical channels 3 and 4
respectively.
The track copy function works the same way. If Digital Source is set to Track Copy and
tracks 7 and 8 are the only tracks selected in Input Routing mode, track 7 will be copied on
the lowest-armed track and track 8 will be copied onto the next higher armed track. For
example, if tracks 2, 4, 5 and 6 are armed, track 7’s data will be copied onto tracks 2 and 5
and track 8 onto tracks 4 and 6.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
6-5
Download from Www.Somanuals.com. All Manuals Search And Download.
In p u t Se le ct io n a n d Ro u t in g , Ch a p t e r 6
6 .5 AUX ROUTING (INP UT AND OUTP UT)
The analog Aux track of the M20 is a unique feature that has special application in Search
mode, because it allows you to hear audio at extremely slow speeds for cueing. The Aux
Routing feature allows you to automatically mix other tracks for recording onto this track.
The back panel Aux Input is permanently routed to the Aux track. The Aux Routing button
selects whether additional inputs will also feed the Aux track (e.g., if tracks 1 and 6 are routed
to the Aux track, then the Aux track will record tracks 1 and 6 and the Aux Input). You can
route any track or group of tracks to the Aux track. If no track buttons are pressed within 10
seconds of entering Aux Route mode, the M20 automatically exits this mode.
It is also possible to automatically record a copy of whatever tracks are currently armed onto
the aux track, so the Aux track always contains the last overdub only. This is called “Auto”
mode.
Operation
You press…
You see…
Enter Aux Route mode
The Aux Routing button
Aux Route indicator
flashes
Select Aux tracks
manually
The desired channels’
Track Input buttons
Aux indicator (below VU
meter for each selected
track input) lights
“Auto” indicator below
the Aux track input
lights; any individual
track “Aux” indicators
disappear
Select Aux tracks
automatically (this
directs all record-enabled
tracks to the Aux track)
Aux Input button (white
button above Aux Rec
Enable)
Exit Aux Route mode
The Aux Route button, or
wait 10 seconds without
pressing any buttons
Aux Route indicator
turns off; channel
indicators and track
select buttons return to
their normal status
Aux routing takes effect only after Record: The routing to the Aux track changes only
upon entering Record mode. Thus, even with Auto Routing enabled, the current
manual or previous auto routing remains in effect until the Aux track goes into
record.
Aux output routing: When in Jog/ Shuttle mode (section 8.4), the Aux output routing
always follows the input routing. Example: If tracks 1 and 5 are routed to the Aux
track, then the Aux track output (which sums tracks 1 and 5 and feeds them to the
Aux Out) will appear on both outputs 1 and 5, unless tracks 1 and 5 are selected as
inputs. This makes it unnecessary to keep a channel on the console dedicated to the
Aux output.
If you turn off Auto mode (press Aux Routing, then press the Aux Input button), the Aux
routing tracks do not return to what had been selected manually prior to automatic Aux
selection; they will show the tracks last armed and recorded.
6-6
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAP TER 7
M ET ERING
With digital recording, it is very important not to exceed the available headroom (and with
20 bits to play with, you have so much dynamic range that there’s no need to push it). The
M20 provides three different metering modes to make it easier to avoid overloads.
7.1 M ET ER M ODE SELECTION
The Peak Mode button cycles through three different meter modes:
·
·
No Peak Hold. Meter levels reflect the current input signal levels.
Momentary Peak Hold (default). Although the meter reflects the current input
signal, the meter also retains the peak level briefly. This is useful if the signal to be
recorded has short transients, which you might miss seeing when they occur.
·
Continuous Peak Hold. The meter also reflects the current input signal, but retains
the highest peak until cleared. Thus, if you can’t monitor a track continuously during
the recording process, you can look at the meter after the recording is over to see the
highest recorded peak.
As you cycle through these options, the main display briefly shows the selected mode.
7.1A CLEARING P EAKS
With continuous peak hold, you will eventually want to clear the peak level indicators on all
8 channels. Press Peak Clear to reset the meters.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
M e t e r in g , Ch a p t e r 7
7.2 M ET ER SETUP
The VU meter scaling, headroom, decay time, and peak hold time are all adjustable using the
Display menus. The Display button is in the lower left group of buttons beneath the meter
display.
Scaling determines whether the meter range is -72 dB to 0 (Normal; this is the default) or -2.0
to +2.0 (Fine).
Headroom sets the headroom amount for the Fine VU meter mode (it does not affect the
normal mode) by letting you specify what value the 0 dB marking represents. The value
ranges from 2 to 22 dB, in 1 dB steps (default = 15 dB).
Decay sets the time for a meter segment to turn off after the signal goes below that level, with
a range of 1 to 99. Each step represents 5 milliseconds, with higher numbers standing for
longer decays. The maximum decay of 99 means a segment will hold for 500 ms. (1/ 2
second). Default = 10.
Peak hold time sets how long peaks will be held when the meters are in momentary Peak
Hold mode, from 1 to 99. Each step represents 250 milliseconds, with higher numbers
standing for longer holds. The maximum decay of 99 means a segment will hold for
24.75 seconds after level has fallen. Default = 8
Operation
You press…
You see…
Enter VU meter scaling
setup
Display button
Display says VU Meter
Scale
Edit VU meter scaling
Up/ Down buttons
Display shows Normal
or Fine scaling
Enter VU meter
headroom page
Display button again
Display says Fine
Headroom
Edit VU meter headroom
Keypad or Up/ Down
buttons to choose the
headroom amount
Display shows amount of
Fine headroom in dB
Enter VU meter decay
page
Display button again
Display says VU Decay
Edit VU meter decay
Keypad or Up/ Down
buttons to choose the
amount of decay
Display shows amount of
meter decay time
Enter VU peak hold page
Edit VU peak hold
Display button again
Display says VU Peak
Hold
Display shows amount of
peak hold time
Keypad or Up/ Down
buttons to choose the
peak hold time
7-2
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAP TER 8
TRANSP ORT CONT ROLS AND
BASIC RECORDING
The transport buttons include Rewind, Fast Forward, Stop, Play, Record, and Eject. The
transport movement may also be controlled by the jog/ shuttle wheel, or various built-in
automatic features.
8 .1 ABOUT THE TAP E COUNTER
The tape counter, located on the right side of the right display, shows the current tape
location. The Tape Counter button selects the counter mode (the 10-digit location counter is
above the Tape Counter switch). Pushing the switch cycles through three different modes.
·
·
ABS Time references the current tape location to the proprietary sample-accurate
ADAT time code formatted into each ADAT tape.
Relative references the current tape location to the relative zero location. The
relative zero point is set by entering an absolute time value into the Locate 00
address. That value is subtracted from the absolute time code value when the tape
counter display is in Relative mode.
·
SMPTE references the current tape location to SMPTE (i.e., ABS + any SMPTE offset,
as described in section 11.6a).
Note: this is NOT necessarily the SMPTE time code printed onto the T/ C track. That
code is displayed in the Reference counter on the left side of the display.
8 .2 STOP
Press to stop the tape transport (Stop button lights steadily). The tape stops moving, but
remains threaded around the head drum.
The tape will unthread (i.e., disengage from the head drum) automatically if no transport
movement occurs during a user-definable timeout period (default = 4 minutes; see section
13.9). Stop will flash. To re-thread the tape, press Stop again (it lights steadily). Note that
entering play from the unthreaded position takes slightly longer than when the tape is
already threaded, due to the time required to wrap the tape around the head drum.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
8-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Tr a n s p o r t Co n t r o ls a n d Ba s ic Re co r d in g , Ch a p t e r 8
8 .3 P LAY
How Play affects tape motion depends on the tape’s status.
If the tape
is…
Pressing Play causes…
You see…
Stopped
Playing
Formatting
Locating
Playback
Play button lights steadily
Play button lights steadily
Play button lights steadily
Play light flashes during
locate, then stays lit when
locate is complete
No change (playback continues)
No change (formatting continues)
Playback after the locate is
complete
Locating
Pressing Play twice stops
Play button lights steadily
autolocation and begins playback
Punch out, and enter Play
Recording
Play button lights steadily
8 .3A P LAY BUT T ON AND SYNC ST AT US
When the M20 is playing and in sync, the Locked indicator (under the last field of the tape
counter) will light solid.
If the M20 loses sync while playing (either as a master or as a slave), the Locked indicator
will turn off.
8 .4 JOG/SHUTTLE W HEEL AND SEARCH
The jog/ shuttle wheel provides convenient access to capstan-engaged rewind, fast forward,
and “scrub” functions (in scrub mode, audio normally comes from the analog Aux track). In
master/ slave situations, the master’s jog/ shuttle wheel controls the slaves, regardless of the
slave’s physical wheel position.
Pushing the Jog/ Shuttle wheel selects between the two modes, as indicated by LEDs above
the Search button. The Search button works with the Jog/ Shuttle wheel, as described toward
the end of this section.
8 .4 A JOG M ODE
Jog advances or rewinds the tape at a rate proportional to thespeed of wheel rotation. This
allows you to move the tape as if you were “rocking the reels” on a n analog machine.
Action…
Turn wheel
clockwise
Result…
You see…
Tape moves forward at a rate
proportional to rotation
speed (1/ 8X to 1X play
speed)
The Search and Play buttons
light, and right arrow above
wheel lights
Turn wheel
counterclockwise
Tape move in reverse at a
rate proportional to rotation
speed (1/ 8X to 1X play
speed)
The Search and Play buttons
light, and left arrow above
wheel lights
When in Jog mode and the transport is idle, the Search and Play buttons will remain lit, and
the Stop button will light steadily (indicating that jogging is paused).
8-2
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 8 , Tr a n s p o r t Co n t r o ls a n d Ba s ic Re co r d in g
8 .4 B SHUTTLE M ODE
Shuttle advances or rewinds the tape at a rate proportional to the degree of wheel rotation.
The greater the degree of rotation from the center detent, the faster the rate.
Action…
Turn wheel
clockwise
Result…
You see…
Tape moves forward at a
rate determined by amount
of rotation (from 1/ 4X to 16X
play speed)
The Search and Play buttons
light, and right arrow above
wheel lights
Turn wheel
counterclockwise
Tape moves in reverse at a
rate determined by amount
of rotation (from 1/ 4X to 16X
play speed)
The Search and Play buttons
light, and left arrow above
wheel lights
Push lit Search
button while in
Shuttle mode
Transport goes into Play
Search and Transport Stop
buttons goes out, Play
remains illuminated
8 .4 C SEARCH BUT T ON
The Search button toggles transport control between the Jog/ Shuttle wheel (Search button lit)
and the transport buttons (Search button dark), making it easy to go in and out of Play mode
while using the Jog or Shuttle function to locate a specific piece of audio.
Action…
Result…
You see…
Push lit Search
button while in
Jog or Shuttle
mode (disable
Search mode)
Push unlit Search
button while in
Jog or Shuttle
mode (enable
Search mode)
Transport goes into Play
Search and Transport Stop
buttons go out, Play remains
illuminated
Transport enters jog/ shuttle
mode:
If in Jog mode, stops;
If in Shuttle mode, moves in
the direction and speed
indicated
Search and Transport Stop
buttons light, Play remains
illuminated
Direction arrows may be lit
in Shuttle mode
Search mode can be initiated simply by turning the jog/ shuttle wheel, or enabled only by
pressing the search button, according to the settings on Page 10 in the Utility menu (section
13.10).
ALESIS M 20 REFERENCE M ANUAL 1.0 6
8-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Tr a n s p o r t Co n t r o ls a n d Ba s ic Re co r d in g , Ch a p t e r 8
8 .4 D SEARCH M ASTER
This function (available only in the ID 1 master M20 in a system) accommodates situations
where you want to use jog on a machine that is not the master (e.g., to find a particular point
on the tape of a slave ADAT only). In this case, you don’t want the slave M20 to follow the
master, but instead, to act as a “temporary locate master” so all machines (including the ID 1
master) park where the designated search master machine parks after a jog or shuttle
operation. The default Search Master machine is ID1. Search Master status is not retained
when the power goes off.
To set which online M20 controls the parking address for all other M20s in a system:
1. Press and hold Search for 2 seconds to enter Search Master Edit mode. The display
shows “Search Master: n” (n = 1 — 8 or All).
2. While continuing to hold Search, use the numeric keypad buttons (1-8, 0) or Up/ Down
buttons to select a search master (default is 1). Releasing the Search button exits the edit
mode without changing the Search mode status.
Selecting a machine other than ID 1 as a search master and activating Search mode (Jogging
or Shuttling) causes the display to indicate momentarily “Machine n Search Master” (n = 1 -
8) or “No Search Master” when All is selected. If you pause a search, ID 1 will query the
search master, update ID 1’s tape counter, and locate all connected machines to the position
of the designated search master.
When search master equals All, ID 1 will not send a locate command to the slaves. All decks
will remain parked after a search.
Releasing the Search button exits Search Master Edit mode, and the M20 reverts to the
display prior to selecting the Search Master.
Note: ID1 must remain online, and the user must observe the time code display when
actively jogging or shuttling because when a slave is the search master, the master’s
tape counter display will only reflect ID1’s tape position until Search mode is paused
and ID1 has located to the search master’s tape position.
8-4
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 8 , Tr a n s p o r t Co n t r o ls a n d Ba s ic Re co r d in g
8 .5 OTHER TRANSP ORT BUTTONS
You press…
If tape is
stopped
If tape is moving
You see…
Eject
Tape ejects
Tape stops
prior to ejection
Tape stops
Tape exits cassette
well, eject button lights
Tape exits master and
slave cassette wells,
eject button lights
Tape exits master
cassette well, eject
button lights
Eject on Master
deck (ID 1)
Master and
slave tapes eject
prior to ejection
Hold Peak
Clear while
pressing Eject
Master tape
only ejects,
MMC Stop
command is
sent to slaves
Tape begins
rewinding at
16X play
Master tape
ejects, MMC
Stop command
is sent to slaves
Rewind
Same
Rewind button lights
steadily
speed,then
accelerates to
85X play speed
Tape rewinds
at 3X real time
and plays
Rewind + Play
(Review mode)
Same, except if
recording,
punches out
first
Play button lights
steadily, Rewind light
flashes
pieces of audio
Tape fast
Fast Forward
Same
Fast Forward button
lights steadily
forwards at 16X
play speed,
then accelerates
to 85X play
speed
Fast Forward +
Play (Cue
mode)
Tape fast
Same, except if
recording,
punches out
first
Play button lights
steadily, Fast Forward
light flashes
forwards at 3X
real time and
plays pieces of
audio
To end a Cue or Review operation, press Play, Stop, Rewind, Fast Forward, or Search.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
8-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Tr a n s p o r t Co n t r o ls a n d Ba s ic Re co r d in g , Ch a p t e r 8
8 .6 RECORD
This button’s operation depends on whether One-Button Record (section 13.4) is enabled or
disabled.
You press…
If tape is
stopped
Recording
begins
If tape is moving
You see…
Record, and
while holding,
press Play
Record
Recording
begins
Record button lights
Recording
begins
No change in
existing status
If recording, record
button lights
If the Format light is lit, entering Record mode will format the tape (see Chapter 4 on
formatting).
8 .6 A P UNCHING INT O RECORD
There are five ways to punch into record while the tape is playing.
·
·
·
Press and hold Record, then press Play at the punch-in point (or vice versa).
With One-Button Record enabled, press Record at the punch-in point.
Use the Record Enable buttons for enabled source inputs. If no tracks are record-enabled
and you press Play and Record, the Record button will flash to indicate Record mode is
pending. At the punch-in point, press the appropriate Record Enable buttons (dynamic
punch, section 13.13, must be enabled for this function to work).
·
·
Use a footswitch (section 8.6e).
Program Auto Record (section 8.8).
8 .6 B P UNCHING OUT OF RECORD
There are five ways to punch out of record.
·
·
·
·
·
Press Stop. The transport punches out of record, then stops.
Press and hold Record, then press Play.
Press Play.
Use the footswitch (section 8.6e).
Turn off a track’s Record Enable button (dynamic punch, section 13.13, must be enabled
for this function to work).
8-6
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 8 , Tr a n s p o r t Co n t r o ls a n d Ba s ic Re co r d in g
8 .6 C RECORD W RIT E-P ROT ECT ION
S-VHS cassettes have a write-protect tab on the side of the tape opposite the “door” that,
when removed to create a small “window,” prevents recording. The M20 senses the write-
protect tab status. If the tape is write-protected, the M20 will not allow recording or
formatting to take place. Attempting to record causes the display to show “ERROR - Write
Protected,” and the transport will enter or remain in play.
How to Override Write-Protection
It is possible to record on a tape that has been write-protected (without resorting to the usual
tactic of taping over the tab). A tape must be in the transport to perform this procedure:
Operation
You press…
You see…
Enable write-protect
override
Press and hold Peak
Clear, then press
Display says “Override
Write Protect”
transport Record button
Press and hold Peak
Clear, then press
Disable write-protect
override
Display says “Sense
Write Protect”
transport Record button
Sense Write Protect auto-reset: Write-protect override resets to the default “Sense Write
Protect” status automatically whenever the tape is ejected.
8 .6 D RECORDING W IT H A FOOT SW IT CH
If any tracks are record-enabled and the tape is playing, pressing the punch footswitch is
equivalent to pressing Record and Play.
If the M20 is already recording, pressing the punch footswitch exits Record mode but the
transport continues to play.
If you plug in a footswitch while the M20 is on, turn the M20 off and then on again so the
machine can sense whether the momentary footswitch is a normally open or normally closed
type.
Note: Footswitch-controlled recording also works in conjunction with Rehearse mode (section 8.7) and
Auto Record mode (section 8.8).
8 .7 REHEARSE M ODE
Rehearse mode allows checking punch point accuracy without actually entering Record
mode. Record-enabled tracks will switch from tape monitor to input monitor at the punch-in
point, and back to tape monitor at the punch-out point.
Operation
You press…
You see…
Enable Rehearse mode
Rehearse button
Rehearse switch lights,
Record light flashes (not
lit solid) while rehearsing
the punch
Disable Rehearse mode
Rehearse button
Rehearse switch light
turns off
ALESIS M 20 REFERENCE M ANUAL 1.0 6
8-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Tr a n s p o r t Co n t r o ls a n d Ba s ic Re co r d in g , Ch a p t e r 8
8 .8 AUTO RECORD
In Auto Record mode, you can program punch in and out points. Pressing Play and Record
prior to the punch-in point causes the M20 to automatically punch in and out at the
programmed points.
You first must set auto-punch points, then enable the function. The auto-punch in and out
points default to autolocation points 98 and 99 respectively. These points automatically store
the locations of the last manual punch in and out, so anytime you have gone into record
manually you can repeat that punch exactly using Auto Record mode if desired.
If the auto punch-out location address is lower than the punch-in address, the Auto Record function
will be disabled (light off), and attempting to enable this causes an error message in the display.
8 .8 A SET T ING AUT O RECORD P UNCH P OINT S
To edit the auto record in and out points (as displayed in the right side of the main display),
follow the steps below.
Operation
You press…
You see…
Display punch in or out
point
Edit button followed by
the Auto Record button
(Auto Record toggles
between displaying
punch in and punch out
points)
Display shows punch in
or out point
Choose specific location
as punch in or punch out
point
Up/ Down buttons
Display shows new
punch in or punch out
point
Edit punch in or punch
out point
Cursor buttons, then
enter numbers (keypad,
Up/ Down buttons, Copy
Tape Location) in the
appropriate fields
Field to be edited
flashing, then replaced
by your entry
Disable punch out point
Exit Auto Record setup
Both Up and Down
buttons simultaneously
(cursor must not be in a
time field)
Display shows Out Pt
Disabled
Press Edit button
Display returns to
normal
8-8
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 8 , Tr a n s p o r t Co n t r o ls a n d Ba s ic Re co r d in g
8 .8 B ENABLE AUT O RECORD
To enable and disable Auto Punch, make sure the machine is not in Edit mode (if necessary,
press the Edit button so that it turns off).
Operation
You press…
You see…
Enable Auto Record
Auto Record button
Auto Record button
lights
Disable Auto Record
Use Auto Record
Auto Record button
Auto Record button
turns off
Record buttons light
solid during punched
region
Press Play and Record
prior to the punch in
point
Note: If the currently selected locate number equals the punch-in locate number, then the In label
lights in the Locate Point block. Similarly, if the currently selected locate number equals the punch-out
locate number, then the Out label lights in the Locate Point block.
8 .8 C SET AUT O P UNCH P OINT S “ON T HE FLY”
Whenever you punch in/ out manually (as opposed to auto-record), the default auto-punch
points assume the times of the manual punch points, and stores them in locations 98 and 99.
Note: This is not the case if punching is enabled/disabled with the Record Enable buttons.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
8-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Tr a n s p o r t Co n t r o ls a n d Ba s ic Re co r d in g , Ch a p t e r 8
8-10
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAP TER 9
AUT OLOCAT ION
The M20 can autolocate to specific points on the tape. Its built-in memory contains 100
different location points, complete with 8-character names. Locate points are used not only
for convenience, but in several other functions of the M20 such as Auto Record and Tape
Offset. These points are saved in the memory of the M20 even when power is turned off,
and may even be saved to the data header of each tape or to a MIDI file via a sysex dump.
The Locate button is positioned next to the other transport buttons (left of the Rewind
button). The currently chosen point is shown in the lower right corner of the main display.
Normally, the upper line of the display shows the location number and name.
Tip: Most M20 users find it convenient to leave the display in Locate Select mode, and
the reference counter in Locate Point mode. If a Display, MIDI, Vari Speed, or Utility
button (these are grouped next to the green Online button) are pressed, they will take
over the top line of the main display, and their button will light. Press Locate Select
to return the display to its default state.
The Locate Point display uses the ADAT’s ABS time as a reference, not the SMPTE time code
track. It can, however, display locate points in SMPTE, Absolute, or Relative modes. If the
Tape Counter (lower left counter in the main display) is in SMPTE, it uses the fixed SMPTE
offset (set in the SMPTE Chase menu) to calculate its value. If the Tape Counter is in Relative
mode, it will subtract the Locate 00 number to calculate its value.
9 .1 ENTERING, SELECTING, AND EDITING LOCATION
P OINTS
9 .1A SET LOCATE
Pressing the Set Locate button (located just above the Stop button) at any time stores the
current tape location (rounded to the nearest subframe) into the next memory location for
later recall. If the Location point is currently 00, the first press of Set Locate stores the
current ABS time into Locate point 01 (shown in the display lower right). The next locate
point is 02, the next 03, and so on up to a maximum of 97. Any previous location address,
but not its name, will be overwritten when using Set Locate. The location block also
indicates whether the location point is one of four special locations (In, Out, Start, or End).
Note: Set Locate will not increment to points 98 and 99, as these are reserved for punch points set
manually. You must select these points with the Up/Down Arrow buttons to update them with the Set
Locate function.
9 .1B COP Y TAP E LOCAT ION
Pressing the Copy Tape Location button stores the current tape location from the tape
counter to the currently-showing locate point indicator; this function is useful for grabbing
location points “on the fly,” as well as for manual auto-punch and loop points. Unlike Set
Locate, doing this does not increment to the next location point number. You must increment
manually.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
9-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Au t o lo ca t io n , Ch a p t e r 9
To select and edit location points:
Operation
Copy Tape Location to
memory
You press…
Copy Tape Location
button
You see…
Tape counter time
(display left side) is
copied to the Locate
Point indicator on the
display’s right side
(Reference Counter).
Locate Point display
shows the current time;
the location block shows
the locate point number
Locate Select display
shows the location point
number and name; the
locate point block shows
the locate point number;
Reference Counter (if in
Locate Pt mode) shows
the point time.
Store Locate Point
Select Locate Point
Set Locate button
Locate Select button, then
Up/ Down Arrows or
number keys to select the
desired location point
Edit Locate Point
Locate Select button, then
press Cursor Left/ Right
to select the field to be
edited (it will flash). Use
Up/ Down Arrows, or
number keys to enter the
new value
Locate Point display
(Reference Counter)
shows the location point
time; the locate point
block shows the locate
point number
Edit Locate Name
Go to Locate Point
Locate Select button, then
Enter/ Name button.
Enter the name.
Locate point block shows
the locate point number
After selecting the
The Rewind or Fast
Forward button flashes
to indicate the direction
of the search. The Locate
button stays lit until the
tape reaches its
desired Locate Point
(using Select Locate
mode), press Locate.
destination.
Locate to Zero*
Locate 0 button
The Rewind or Fast
Forward button flashes
to indicate the direction
of the search. Locate 0
lights stays lit until the
tape reaches its
destination.
*Whether the tape counter display is ABS (Absolute), Relative, or SMPTE, the zero point is
always at ABS 00:00:00:00 (the beginning of the audio section, just after the leader).
9-2
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 9 , Au t o lo ca t io n
9 .2 DEFERRED P LAY AND RECORD
To automatically enter Play mode after locating, press Play before a locate completes. To
cancel while tape is moving, press Stop, Rewind, FF, or Search.
To automatically enter Record mode after locating, press Play and Record before a locate
completes. To cancel while tape is moving, press Play, Stop, Rewind, FF, or Search.
9 .3 P LAY-AFT ER-LOCATE (AUTO P LAY)
To always enter Play mode after completing a locate, press Auto Play (its button lights). This
button can be pressed at any time. To cancel, press Stop or some other transport control
before the location is complete.
9 .4 LOOP BETW EEN START AND END LOCATE P OINTS
(AUTO RETURN)
You can set up “loop points” (start and end locate points; see section 9.1), and program the
M20 to automatically return to the start locate point after reaching the end locate point. This
works during play or record. The start and end locate points are chosen from the possible
100 locate points in memory, and default to locations 01 and 02 respectively.
To enable Auto Return, press the Auto Return button at any point (stopped, playing, or
recording) as long as the tape is before the end point. Enabling Auto Return when the tape is
past the end point has no effect.
If the end point is reached while recording, the M20 will punch out before rewinding to the
start point.
Turning off Auto Return while it’s returning to the start point initiates normal Rewind mode.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
9-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Au t o lo ca t io n , Ch a p t e r 9
9 .4 A SET T ING LOOP ST ART AND END P OINT S
To edit the start and end locate points, follow the steps below.
Operation
You press…
You see…
Show start locate point
Edit button followed by
the Auto Return button
Up/ Down buttons or
number keys
Cursor Right button,
then enter numbers
(keypad, Up/ Down
buttons,) in the
Display shows Start
Point location
Display shows new start
Point location
Field to be edited
flashing, then replaced
by your entry
Choose start locate point
Edit start locate point
appropriate fields (or use
Copy Tape Location)
Auto Return button
again (toggles between
start and end points)
Up/ Down buttons or
number keys
Cursor buttons, then
enter numbers (keypad,
Up/ Down buttons, Copy
Tape Location) in the
appropriate fields
Display end locate point
Display shows End Point
location
Choose end locate point
Edit end locate point
Display shows new End
Point location
Field to be edited
flashing, then replaced
by your entry
Loop Count feature: For continuous looping of a section, Auto Return and Auto Play are
both turned on. Hold Peak Clear while pressing Auto Return to temporarily display
the current loop count. To preserve the tape from accidental wear, the M20 will
automatically exit Auto Play mode after 100 continuous loops of Auto Return.
9 .5 SET P RE-ROLL
For rehearsal or recording, it’s often important to hear a few seconds of music prior to an
entry point. Setting a pre-roll time locates the tape prior to any location point by the specified
amount of pre-roll (0 to 25 seconds; default is 5 seconds). Setting pre-roll = 0 causes the tape
to locate to the cue point (same as disabling pre-roll).
Pre-roll also works when looping between two points.
Operation
You press…
You see…
Display Pre-Roll time
Edit button followed by
the Pre-Roll button
Enter time with numeric
keypad or Up/ Down
buttons
Display shows existing
pre-roll time
Display shows new Pre-
Roll time
Edit Pre-Roll time
Leave Pre-Roll Edit mode
Press Edit button again
Edit light goes out. Pre-
Roll button light returns
to its on or off status.
9-4
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 9 , Au t o lo ca t io n
9 .6 SET P OST-ROLL
For rehearsal or recording in Auto Record mode, setting a post-roll time causes the tape to go
beyond the punch-out point by the specified post-roll time prior to stopping (0 to 25 seconds;
default is 5 seconds). Setting post-roll = 0 causes the tape to locate to the cue point (same as
disabling post-roll).
Operation
You press…
You see…
Display Post-Roll time
Edit button followed by
the Post-Roll button
Enter time with numeric
keypad or Up/ Down
buttons
Display shows existing
post-roll time
Display shows new Post-
Roll time
Edit Post-Roll time
End Post-Roll edit mode
Press Edit button again
Edit light goes out. Post-
Roll button light returns
to either on or off
Post-roll also affects the time when looping between two points.
Tip: If you have to do a number of takes/ overdubs at the same locations, use Auto
Return and Auto Record together. Set the Loop Start point to the Punch In point,
and the Loop End point to the Punch Out point. Setting a Pre-Roll and Post Roll
allows the M20 to be in sync before the punch, and allow the talent to hear their cues.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
9-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Au t o lo ca t io n , Ch a p t e r 9
9 .7 FOOTSW ITCH-CONTROLLED LOCATION
If the transport is playing, pressing the Locate/ Play footswitch locates the transport to the
Auto Return locate point, then stop or enter play, depending on the setting of the Auto Play
switch (section 9.3).
Pressing the Locate/ Play footswitch while the tape is locating initiates stop.
Note: If the transport is stopped, pressing the Locate/Play footswitch initiates play.
9-6
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAP TER 10
VARISP EED
Varispeed changes the sampling rate to change the audio’s pitch. This feature only applies
when the Clock Source is set to INT (Internal). Pitch mode is automatically set to Fixed
whenever the M20 is being controlled by an external unit (for example, when SMPTE Chase
is on).
The varispeed range is -300 through +100 cents (-15.91% to +5.95%) at a base 48 kHz sample
rate and -200 through +200 cents (-10.91% to +12.25%) at a base 44.1 kHz sample rate. This
allows a total sample rate range from approximately 39.289 kHz (-200 cents @ 44.1 kHz) to
50.854 kHz (+100 @ 48 kHz). Note that pitch changes affect all slave machines. Varispeed
settings are retained in memory.
Operation
You press…
You see…
Enter Varispeed Edit
mode
Varispeed button
Display shows amount of
varispeed change in cents
and as a percentage
Display shows amount of
varispeed change
Set varispeed amount
Enter amount with
numeric keypad or
Up/ Down buttons.
When Vari is set to 000,
Up/ Down buttons select
+ or - before entering a
number. If Vari is any
other value, Up/ Down
increments/ decrements
the value.
Enable varispeed
Disable varispeed
Press Pitch Mode button
until…
Press Pitch Mode button
until…
Vari in the pitch block
Fixed in the pitch block
In Varispeed mode, the time counters will not show the true elapsed (i.e., “clock on the
wall”) time intervals.
Synchronization warning: Any time code being sent from the M20 will be sped
up or slowed down when using Varispeed mode. This may cause synchronization
problems in other equipment that is slaved to the M20. If you’re using SMPTE time
code synchronization anywhere in your project, use varispeed with great caution.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
10-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Va r is p e e d , Ch a p t e r 10
10-2
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAP TER 11
SM P TE, SYNC, AND OFFSET
FUNCT IONS
The buttons described in sections 11.1 through 11.5 are located under the main (right)
display.
The buttons described in sections 11.6 through 11.9 are part of the Edit button group toward
the M20’s lower left under the meter display and track arming buttons.
11.1 CLOCK SOURCE
This switch cycles through up to seven different clock selections.
·
·
·
·
·
·
·
Internal (M20 internal clock)
Video
ADAT (if the unit is seeing a valid 9-pin ADAT Sync In connection)
Word Clock
I/ O card (if one is installed in the Expansion Slot on the back panel)
SMPTE
Optical
Note: Setting the clock to Int on an ADAT slave M20 automatically selects its ADAT clock option.
Also, selecting any source other than Internal when no valid clock is available automatically switches
the M20 to internal clock, and flashes the currently selected clock indicator until the M20 senses a
valid clock.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
11-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SM P TE, Syn c, a n d Offs e t , Ch a p t e r 11
11.2 SM P TE RATE
SMPTE Rate cycles through six different SMPTE frame rates and types; this affects both
SMPTE time code input and M20 SMPTE time code output. It is not possible to receive and
transmit different frame rates simultaneously.
·
·
·
·
·
·
24
25
film
European (PAL) video
NTSC color video
NTSC color video drop frame
American monochrome video, most audio applications
American monochrome video drop frame
29.97
29.97 Drop
30
30 Drop
When receiving SMPTE time code, input and output frame rates are set to the incoming
frame rate (displayed by the SMPTE frame rate indicator). 29.97 and 30 frames/ sec are not
identified automatically due to possible source speed variations, and must be set manually.
Frame rates when receiving video are adjusted automatically, as follows:
Clock Source is set
to…
Incoming video
is…
Frame rate…
Video
Video
NTSC
PAL/ SECAM
can select 29.97 or 29.97 drop frame
is set to 25 fps
11.3 TIM E CODE SOURCE
This switch selects either:
·
The time code generated by the M20, with the start time set in the Internal Gen pages
(Internal mode)
·
An outside SMPTE source (External mode)
11.3A INT ERNAL
Time code generated by the M20 appears at the Time Code Output jack. The internal
generator generates SMPTE/ EBU time code according to several parameters that are set in
Int Gen Edit mode. Code may be generated only when the transport is moving, or when it is
stopped. The numbers of the time code being generated may be referenced to tape in several
ways, or set independently by the user.
TC Input button: In any case, the internal generator of the M20 will only start issuing
code when the white TC Input button, below the TC Track meter and Record Arming
button, is turned on. As long as the TC Source is set to Internal, the internal
generator (NOT the rear panel Time Code In jack) is considered the “input” source
for this button.
When the TC track is not in Input mode and is playing back, the time code output comes
from the TC track on the tape, if there is time code printed.
11-2
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 11, SM P TE, Syn c a n d Offs e t
For example, Int Gen always generates time code when the Internal Generator TC Start Ref
parameter is set to User Set, Free Run, and the TC Input button is lit. Setting this parameter
to ABS Time generates time code only if there is a valid, ADAT-formatted tape in the
transport. Setting this parameter to TC Track generates time code only if there is valid time
code recorded on the TC track of the tape.
With the Time Code track in Input mode, the time code start point and internal generator
functions vary, as shown below.
TC
Int Gen
Start Ref
Intern
Gen
status
Disabled
Internal Gen will…
How Time Code Starts
Source
Mode
External
N/ A
N/ A
Input time code passes through
to the output
Internal
Internal
Internal
ABS
Time
Enabled
Enabled
Enabled
Run immediately (in
Free Run mode) or when
tape is moving (in
Time code starts from the ABS
time + internal generator ABS
offset
Play/ Rec mode)
User Set
TC track
Run immediately (in
Free Run mode) or when
tape is moving (in
Time code starts from the
specified time
Play/ Rec mode)
Run immediately (in
Free Run mode) or when
tape is moving (in
Internal generator time code
starts from the TC track.
Play/ Rec mode)
Caution: If the TC track is put into record when the internal generator is disabled and the TC track is
in Input mode, the TC track will record no time code and will erase any previous TC track time code.
11.4 CHASE REFERENCE
Chase Reference chooses between two chase (synchronization) reference options. The tape
time code playback mode automatically follows the incoming time code frame rate.
·
·
With ABS Time mode, the M20 will chase incoming SMPTE based on its absolute time
reference (the standard ADAT-format time code).
With Tape TC mode, the time code track recorded on tape provides the reference for
locking to incoming SMPTE. If there is no time code on tape, the tape will not chase
incoming SMPTE.
Note: In both cases, when synchronizing to optical or word clocks, the time code must be synchronous
to the sample rate (this will always be the case if synchronizing to absolute time; if synchronizing to
tape time code, the TC track must be synchronous to the clock). For the M20 to lock, you must also
make sure that the incoming time code is synchronous to the incoming word clock.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
11-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SM P TE, Syn c, a n d Offs e t , Ch a p t e r 11
11.5 REFERENCE COUNTER
This button cycles through the reference counter display options (this display is above the
Reference Counter button). The selected display option (just below the display digits) shows
one of the following times:
·
·
·
·
·
SMPTE In
Locate Pt
Tape TC
Incoming time code
2-digit locate address shown in the Locate Pt block
TC track time code
Int Generator
Offset
Internal generator time code
Tape or chase offset
11.6 SM P TE CHASE
This switch toggles Chase mode on and off. When enabled (Chase LED on), the M20 chases
(follows) any external SMPTE Time Code input.
To display or edit the chase parameters, press the Edit button then the SMPTE Chase button.
There are 4 pages of parameters. Pressing the SMPTE Chase button cycles through the 4
pages.
11.6 A SET SM P TE OFFSET VALUE (P AGE 1)
You may specify a SMPTE offset (up to ±24 hours) that is added to or subtracted from the
Time Code reference (either ABS TIME or TAPE Time Code). Example: If you add an offset of
00:01:00:00 (1 minute), the M20 interprets an incoming SMPTE time of 00:05:30:00 as
00:06:30:00, and the SMPTE Tape Counter display shows 00:06:30:00.
Note: To edit the Samples field, select the Subframes field, then press the Cursor Right button (for
more on subframes, see section 3.3).
Operation
You press…
You see…
Select field to edit
Left/ Right Arrow
buttons to scroll to
desired field
Selected field flashes
Change sign (+ to add
offset, - to subtract)
Change numeric field
value
Up/ Down buttons
Flashing sign changes
from + to -
Field to be edited flashes,
then is replaced by your
entry
Enter two-digit number
from keypad (leading
zeroes must be entered)
or use Up/ Down buttons
Edit button or any other
Edit Group button
Exit SMPTE Offset setup
Display leaves SMPTE
Offset function
11-4
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 11, SM P TE, Syn c a n d Offs e t
11.6 B SET SM P T E CHASE M ODE (P AGE 2)
There are two chase modes: Frame-Lock (default) and Lock/ Release (i.e., Lock and Release
to clock). Chase must be enabled.
The Down Arrow button or keypad button 0 selects Frame-Lock. With Frame-Lock mode,
the M20 will relocate to incoming time code if it does not match the current tape location.
The Up Arrow button or any keypad button greater than 0 selects Lock/ Release. In
Lock/ Release, the M20 references the incoming time code location to establish a lock. Once
locked, it ignores the time code data and follows the selected external clock source to
maintain lock.
Definition of Lock/Release mode: In Lock/ Release, if the incoming time code stops for
more than the flywheel amount (section 11.6c), is running but not advancing its
frame numbers, starts counting frames backwards, or begins to advance at a non-
play speed, the M20 will stop playing and attempt to chase to the time code location.
If the time code is advancing forward but has a discontinuity, the M20 will continue
to play without attempting to chase to the new time code location. Lock and release
mode is a more “forgiving” mode in difficult time code applications where the
master code has dropouts or jumps from one type to another.
11.6 C SET FLYW HEEL DURAT ION (P AGE 3)
This parameter selects the maximum number of invalid or missing time code frames that will
be ignored (up to 150 maximum). In Frame-Lock chase mode, the M20 keeps playing for the
flywheel time as if valid time code was present, then chases when valid time code data
reappears. In Lock/ Release chase mode, flywheel sets the amount of time that the M20 will
continue to play in the absence of incoming time code before stopping the tape.
Use the Up/ Down buttons, or enter a 3-digit number with the keypad (leading zeroes must
be entered).
11.6 D P ARK AHEAD (P AGE 4 )
The M20 can park tape ahead of the last valid time code input, up to 59:29 (seconds/ frames).
Default is 00:00 (tape does not park ahead). The Park Ahead parameter is available to make
lockup times shorter in situations where the master time code source drops out or drifts for a
few seconds as it stops and starts (for example, when a VTR disengages).
Operation
You press…
You see…
Select field to edit
Left/ Right Arrow
buttons to scroll to
desired field
Cursor under selected
field
Change numeric field
value
Enter two-digit number
from keypad (leading
zeroes must be entered)
or use Up/ Down buttons
Edit button or any other
Edit Group button
Your entry replaces
current field value
Exit Park Ahead setup
Display leaves Park
Ahead function
ALESIS M 20 REFERENCE M ANUAL 1.0 6
11-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SM P TE, Syn c, a n d Offs e t , Ch a p t e r 11
11.7 INTERNAL GENERATOR
This button turns the internal time code generator on and off (Time Code Source must be set
to Internal; see section 11.3). Setting the Time Code Source to External automatically turns off
the Internal Gen function. If you press Int Gen when TC Source is External, the display will
read “TC Source not internal”. If the TC Source is Internal, then the generator may be turned
on or off.
TC Input button: In any case, the internal generator of the M20 will only start issuing
code when the white TC Input button, below the TC Track meter and Record Arming
button, is enabled.
If chase is enabled, Time Code Source = Internal and the Time Code Track is in Input mode,
then the time code output will be the Chase reference (ABS TIME or TAPE TC) plus any
SMPTE Offset.
If chase is disabled, Time Code Source = Internal and the Time Code Track is in Input mode,
then the time code output is selected on the following pages.
Note: If the TC Source is Internal, the time code track is in record, and the internal generator is off,
then any previously recorded time code will be erased.
11.7A GENERAT OR M ODE (P AGE 1)
In Free Run mode, enabling/ disabling Internal Gen respectively starts/ stops the internal
generator. In Play/ Rec mode, enabling Internal Gen causes the internal generator to run only
while playing or recording. Disabling Internal Gen always stops the internal generator.
The Down button or keypad button 0 selects Play/ Rec (default).
The Up button or any keypad button greater than 0 selects Free Run.
11-6
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 11, SM P TE, Syn c a n d Offs e t
11.7B TIM E CODE ST ART REFERENCE (P AGE 2)
This page sets the internal generator’s starting reference. Use the Up/ Down buttons to select
one of three options, or use the keypad numbers given below.
·
·
·
With ABS Time (keypad 0), the internal generator’s start address is the current ABS
address plus any ABS offset (set on Page 3). The generator outputs time code based on
the M20’s absolute time track. Note: For time code to appear at the rear panel time code output,
the time code track must be input-enabled, the generator must be running, and a formatted tape
must be loaded.
With TC Track (keypad 1), the current TC track time code becomes the internal
generator’s start address. The generator will continue generating the same format code
as on the time code track when the input is enabled and the generator is running. If no
code exists on tape, no time code will be output or recorded; the display temporarily
shows “TC Reference not present” if you try to turn Int Gen on.
With User Set (any keypad number >1), the generator will output time code that is
synchronous to the absolute time, but starting at an arbitrary address as defined in the
next page. The time code will only be generated while the time code track is input-
enabled. The generator retains the address at which it was stopped, and continues when
re-started. In other words, whenever the generator is running with a User Set TC Start
reference, it updates the User Set Start number.
11.7C ABS/ST ART OFFSET (P AGE 3)
This page shows “ABS” if Page 2 is set to ABS, and “START” if Page 2 is set to User Set.
If the Internal Generator is set to ABS, you can enter an offset for the time code output
compared to the ABS time.
If the Internal Generator is set to User Set, you can enter a new generator start time. The
display shows the current generator location when last stopped in User Set mode.
If the generator is running, this page will show the previous start value, but the cursor will
not be displayed as the start time cannot be edited while the generator is running.
Here’s how to edit the ABS/ Start offset value:
Operation
You press…
You see…
Select field to edit
Left/ Right Arrow
buttons to scroll to
desired field
Cursor under selected
field
Change numeric field
value
Enter two-digit number
from keypad (leading
zeroes must be entered)
or use Up/ Down buttons
Edit button or any other
Edit Group button
Your entry replaces
current field value
Exit ABS/ Start setup
Display leaves ABS/ Start
function
ALESIS M 20 REFERENCE M ANUAL 1.0 6
11-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SM P TE, Syn c, a n d Offs e t , Ch a p t e r 11
11.7D USER BIT S (P AGE 4 , OR P AGE 3 IF THE P AGE 2 VALUE
IS T C T RACK)
This page allows entering 8 hex characters (0 - F) into the user bits of the SMPTE time code.
These bits are used to identify reels, projects etc. and may be displayed by an appropriate
SMPTE time code reader.
Operation
You press…
You see…
Select digit to edit
Left/ Right Arrow
buttons to scroll to
desired digit
Cursor under selected
digit
Change digit value
Use Up/ Down buttons
or enter digit from
keypad (the 1 key cycles
through 1-A-B-C, the 2
key cycles through 2-D-
E-F)
Your entry replaces
current digit
Exit User Bits setup
Edit button or any other
Edit Group button
Display leaves User Bits
function
11.8 TAP E OFFSET
This function is intended for offsetting individual M20s or ADATs from each other
within a multi-ADAT system only, not for setting an offset from an external SMPTE
time code master. For setting a SMPTE offset see section 11.6a.
This offsets (shifts in time) the master ADAT (ID1) compared to the slave ADATs, or
individual slaves compared to the master. The offset can be referenced to ABS time code or
between two locate points.
An offset-enabled slave is offset by the specified amount from the master machine. With
offset enabled on the master, it is offset by the specified amount from all slave units (i.e., all
slaves are offset by the negative amount compared to the master unit).
In Edit Tape Offset mode, the Up/ Down buttons choose between (ABS) Time Code and
Location.
If Offset Mode = Time code, the reference counter displays the offset amount (up to ±24
hours) in hours, minutes, seconds, frames, and subframes. (To edit the Samples field, select
the Subframes field, then press the Cursor Right button.)
11-8
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 11, SM P TE, Syn c a n d Offs e t
Operation
You press…
You see…
Select Time Code field to
edit
Left/ Right Arrow
buttons to scroll to
desired field
Selected field flashes
Change sign (+ to add
offset, - to subtract)
Change numeric field
value
Up/ Down buttons
Flashing sign changes
from (+) to (-)
Field to be edited flashes,
then is replaced by your
entry, cursor goes to next
field to the right
Enter two-digit number
from keypad (leading
zeroes must be entered)
or use Up/ Down buttons
Edit button or any other
Edit Group button
Exit Tape Offset setup
Display leaves Tape
Offset function
If Offset mode = Locate, the time code counter displays the two locate points that define the
offset as “aa to bb,” where aa and bb are locate numbers ranging from 00 through 99. They
both default to 00 on power-on, since identical locate points result in no offset. Setting Locate
aa before or after Locate bb creates a positive or negative offset, respectively (offset = locate
bb - locate aa). To see the actual offset time, change the mode to Time Code and the time
code display will show the offset amount.
Operation
You press…
You see…
Select 1st Locate point
Right Arrow button to
scroll to Locate 1 field
Enter two-digit number
from keypad (leading
zeroes must be entered)
or use Up/ Down buttons
Right Arrow button to
scroll to Locate 2 field
Enter two-digit number
from keypad (leading
zeroes must be entered)
or use Up/ Down buttons
Tape Offset button
Selected field flashes
Change numeric field
value
Field to be edited flashes,
then is replaced by your
entry
Select 2nd Locate point
Selected field flashes
Change numeric field
value
Field to be edited flashes,
then is replaced by your
entry
(Optional) check time of
offset
Cursor jumps to Offset
mode line
Change offset readout to
Time Code
No (Down Arrow)
button
Offset mode changes to
Time Code, display
shows offset time in
H:M:S:F:SF
Exit Tape Offset setup
Edit button or any other
Edit Group button
Display leaves Tape
Offset function
Note: ABS has priority over Locate settings. In other words, if you choose a Locate offset, then go to
the ABS display to see the time offset, then change the ABS setting, the machine will follow the ABS
setting.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
11-9
Download from Www.Somanuals.com. All Manuals Search And Download.
SM P TE, Syn c, a n d Offs e t , Ch a p t e r 11
11.9 TRACK DELAY
Track Delay allows offsetting individual tracks in time. Example: Delaying a snare part
slightly compared to other drums can give a more “laid back” feel.
Maximum delay time is 170.0 ms at 48 kHz and 185.0 ms at 44.1 kHz, adjustable in 0.1 ms
steps (0 through 8160 samples). The delay time displayed is accurate only while playing at
normal pitch (48 kHz or 44.1 kHz), and will not compensate for pitch changes or external
clock variations.
To change delay for individual tracks:
Operation
You press…
You see…
Select track to edit
Track Delay button to
cycle through the 8
tracks, or press track
input enable button
Cursor right
Track # in Trk Delay line
changes, cursor appears
under matching track
meter
Select Delay Time
display (ms or samples)
Change Delay Time
display (ms or samples)
Select Delay time for
editing
Cursor appears under ms
Up/ Down buttons
ms or smp in Trk Delay
line
Cursor parks under
rightmost digit
Use Cursor Left/ Right
buttons to place cursor
under numeric field
Change Delay time
Use Up/ Down buttons
or enter 4-digit number
(leading zeroes required)
Your entry replaces field
to be edited, track meter
shows rough “bar graph”
of delay time
Exit Track Delay setup
Edit button or any other
Edit Group button
Display leaves Track
Delay function
11-10
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 11, SM P TE, Syn c a n d Offs e t
To change delay for several tracks at once:
Operation
Select tracks to edit
You press…
Press track Input Enable
You see…
Trk Delay line changes
name to Group Delay
button for one track to be
delayed and while
holding it, press Input
Enable buttons for other
tracks to be delayed. The
All Input button selects
all tracks.
Select Delay Time
display (ms or samples)
Change Delay Time
display (ms or samples)
Select Delay time for
editing
Cursor right
Cursor appears under ms
Up/ Down buttons
ms or smp in Trk Delay
line
Cursor parks under
rightmost digit
Use Cursor Left/ Right
buttons to place cursor
under numeric field
Change delay time
Use Up/ Down buttons
or enter 4-digit number
(leading zeroes required)
Your entry replaces field
to be edited, track meter
shows rough “bar graph”
of delay time
Exit Track Delay setup
Edit button or any other
Edit Group button
Display leaves Track
Delay function
ALESIS M 20 REFERENCE M ANUAL 1.0 6
11-11
Download from Www.Somanuals.com. All Manuals Search And Download.
SM P TE, Syn c, a n d Offs e t , Ch a p t e r 11
11-12
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAP TER 12
M IDI FUNCT IONS
There are seven pages of MIDI functions. Pressing the MIDI button cycles through the pages
in order.
12.1 M IDI DEVICE (P AGE 1)
Selects the M20’s device ID (1—127 or All) so that MIDI Machine Control systems with
multiple M20s can address them separately. Selecting All means that M20s respond to all
incoming MIDI messages. Default ID = 000.
Use the Up/ Down buttons or number keys to enter the desired ID. To enter All, scroll past
127, or enter any number greater than 127.
12.2 M M C OUTP UT (P AGE 2)
Enables or disables the M20 from transmitting MIDI Machine Control commands from the
MIDI output. Default is Off.
Use the Up/ Down buttons to choose on or off.
12.3 M TC FOLLOW GEN (P AGE 3)
Sets whether MTC (MIDI Time Code) will be generated simultaneously with SMPTE. Default
is Off.
Use the Up/ Down buttons to choose on or off.
12.4 SEND SYSEX DUM P ? (P AGE 4 )
Sends the current setup information (as MIDI system exclusive data) via the MIDI Out port.
Setup information includes all data currently in the unit such as locate point names and
addresses, track delays, tape offsets etc. Sending a Sysex dump to the input of another M20
gives it the same setup as the transmitting M20. This data can also be saved to a storage
device (Alesis Data Disk, sequencer program, etc.) to store specific setups for later recall.
Action to perform…
Display shows…
With Page 4 selected, press Yes
Wait for dump to end
Sending Sysex Dump
Initial Page 4 display
ALESIS M 20 REFERENCE M ANUAL 1.0 6
12-1
Download from Www.Somanuals.com. All Manuals Search And Download.
M IDI Fu n ct io n s , Ch a p t e r 12
12.5 RECEIVE SYSEX DUM P ? (P AGE 5)
Receives setup information (as MIDI system exclusive data) via the MIDI In port. This could
come from another M20 or a data storage device.
Action to perform…
Display shows…
With Page 5 selected, press Yes
Initiate dump from the
transmitting device
Rdy to Recv Sysex Dump
Receiving Sysex Dump
Wait for dump to end
Sysex Receive Complete briefly when dump is
complete
Note: The current setup does not update unless a complete dump is received. If the reception is
interrupted, the display shows Received Incomplete Dump until any other button is pressed.
12.6 SEND SOFTW ARE? (P AGE 6 )
This function sends the M20’s current operating system software via the MIDI Out port,
typically to another M20 to update its operating system, or to a data storage device for
backup. The tape must be ejected prior to sending software. This operation will take
approximately 12 minutes.
Action to perform…
Display shows…
With Page 6 selected, press Yes
Initiate send
Press ENTER to confirm or NO to exit
Press Enter
Wait for software to be transmitted
Exit by pressing any edit or keypad
button
Percentage of send completed
Whatever is associated with button you
pushed
Note: To cancel a transmission, hold the Stop button and press Eject. Be careful ó cancelling a send
may leave a receiving unit non-functional.
12.7 LOAD SOFTW ARE? (P AGE 7)
This page allows updating the M20 operating system via data received at the MIDI In port,
typically from another M20, a data storage device, or computer sequencer. The tape must be
ejected prior to loading software. This operation will take from 6 to 12 minutes depending
on the sysex file source (e.g. M20, computer sequencer, etc.).
Action to perform…
Display shows…
With Page 7 selected, press Yes
Code seg will be erased. Press ENTER to
confirm or press NO to exit.
Erasing code block…
Erase existing code by pressing
Enter
Update M20 software
Rdy To Receive Software
Please Wait — Updating
Initiate send at transmitting device
(if using an M20, see section 12.6)
Wait for load operation to end
(approximately 6 minutes from the
Alesis sourced MIDI file, 12
minutes from another M20).
Software Updated. After 4 seconds, the
message changes to Restarting … The
machine automatically restarts.
12-2
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 12, M IDI Fu n ct io n s
Before loading new softw are into your M20, alw ays save a “backup” of the existing
softw are in the M20 to your computer sequencer or data storage device.
This w ill safeguard against any mishaps that could occur during the
softw are loading process (i.e. corrupted MIDI file, equipment failure, etc.).
WARNING: If the M20 loads an incomplete update or incorrect data, the main
display will show an error message. If a software load attempt fails, it is necessary to
properly load the software before using the M20. The M20 will be nonfunctional
until the operating system is successfully loaded. You will need to power-cycle the
M20 (turn the unit off then on again) after an incomplete load. When the M20
restarts, the main display will prompt you to erase the software again. Erase the old
software and re-send the updated M20 software.
For more on M20 software, see Tutorial 6 in Chapter 15.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
12-3
Download from Www.Somanuals.com. All Manuals Search And Download.
M IDI Fu n ct io n s , Ch a p t e r 12
12-4
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAP TER 13
UTILITY M ENU
There are 22 pages of Utility functions. Pressing the Utility button cycles through the pages in
order.
Shortcut: To jump directly to a particular page, hold Utility down and enter the page
number form the keypad, using leading zeroes to access pages 01-09.
13.1 DIGITAL OUT (P AGE 1)
Selects the digital output format and resolution for tapes formatted in 20-bit mode (there is
no choice of digital output with 16-bit tapes).
Procedure: Use the Up/ Down buttons (or keypad buttons 0-4) to choose among the following:
20-bit (default). All 20 bits of audio are available at the optical and I/ O card outputs.
16-bit dithered. The digital audio optical output from a 20-bit tape or digital input source is
dithered down (using the 4 least-significant bits of the 20-bit signal) to a 16-bit output. This is
the preferred 16-bit mode.
16-bit. This simply truncates the 4 least-significant bits from a 20-bit tape or digital input
source.
Digital Thru. The digital audio input from an optical or I/ O card source goes directly to the
optical or I/ O card output. The source word length is unchanged.
13.2 ONLINE SOURCE (P AGE 2)
Sets the control source when Online mode (section 13.2a) is enabled.
Procedure: Use the Up/ Down buttons (or keypad buttons 0-3) to choose among the following:
ADAT (default). Receives control commands from the ADAT 9-pin Sync In connector.
MIDI. Receives MIDI Machine Control commands from the MIDI In port.
RS-422 (Software version 2.0 and above only). Receives commands from the RS-422 port.
Note: MIDI does not need to be selected to receive Sysex and software dumps (sections 12.5 and 12.7).
13.2A ONLINE BUT T ON
The Online button determines whether the M20 will respond to control commands from the
source specified in Online Source (section 13.2). Regardless of the Online status and source,
the machine will continue to monitor and pass commands back and forth on its sync port.
Online cannot be switched off on a lone-M20 system.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
13-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Ut ilit y M e n u , Ch a p t e r 13
When enabled (Online = LED lit), the machine responds to commands from the selected
Online Source. Local control may be allowed or ignored, as set on Utility Page 3 (section
13.3).
When disabled (Offline = LED off), the machine ignores commands from the selected Online
Source.
Note: Certain user parameters are not editable when a machine is online, and only some parameters
may be edited regardless of online status. The relevant parameters are duplicated and stored in 2
groups. One group is used when the machine is online, and the other when the machine is offline.
13.2B INDEP ENDENT SLAVE M ODE
A slave machine will always respond to front panel transport button presses (subject to the
local/ remote setting on Utility Page 3, section 13.3), regardless of whether it is online or
offline.
13.3 ONLINE CONTROL (P AGE 3)
Chooses whether local control is also available if a remote control source is selected.
Procedure: Use the Up/ Down buttons (or keypad buttons 0 and 1) to choose between the
following:
Local/Remote (default). Receives control commands from front panel and LRC as well as the
selected online source.
Remote. Allows control only from the selected remote source. There is no local control from
any button on the front panel other than to disable the Online function.
13.4 ONE-BUTTON RECORD (P AGE 4 )
With One-Button Record off, it is necessary to press both Play and Record to initiate
recording. With One-Button Record on, simply pressing Record initiates recording.
Procedure: Use the Up/ Down buttons to turn One-Button Record on or off.
13.5 INP UT M ONITOR (P AGE 5)
Determines whether the analog input is monitored directly from the inputs or through the
A/ D and D/ A converters.
Procedure: Use the Up/ Down buttons to choose between the following:
ADC/DAC (default). The analog input is monitored after going through the A/ D and D/ A
converters. Monitoring through the converters adds a very slight bit of latency
(approximately 600 µseconds), but accurately reflects any changes to the signal that occur
from the conversion process.
Direct. The analog input is monitored directly from the inputs without going through digital
conversion.
13-2
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 13, Ut ilit y M e n u
13.6 CROSSFADE TIM E (P AGE 6 )
Sets the crossfade time when the M20 transitions from Play to Record, or Record to Play.
With a 48 kHz sample rate, the crossfade values range from 5.4 ms - 1.365 seconds. At 44.1
kHz, the crossfade values range from 5.8 ms - 1.486 seconds. Default is 10 ms.
Procedure: Use the Up/ Down buttons to cycle through the 32 crossfade times.
When punching into the middle of a low-frequency tone, a crossfade time that is too
short may cause a click.
13.7 TIM E CODE OUTP UT LEVEL (P AGE 7)
Adjusts the time code peak-to-peak output level from 0.1V to 3.0V in 0.1V increments.
Procedure: Use the Up/ Down buttons to increment/ decrement in 0.1V increments, or enter
the two-digit number directly with the keypad. Leading zeroes must be entered (e.g., for a
0.5V output, enter 0 then 5). Default is 1.0V.
13.8 REW IND/FAST FORW ARD T C OUTP UT (P AGE 8 )
The M20 can output SMPTE and MTC any time the tape is moving (fast forward, cue,
rewind, jog, shuttle, etc.) if this option is enabled. When off, time code is transmitted only in
Play mode. Default is off.
Procedure: Use the Up/ Down buttons to turn Rewind/ Fast Forward Time Code Out on or
off.
Turn this OFF if your system (mixer automation, computer sequencer etc.) acts strangely
when you fast wind the M20; it probably can’t understand the fast bursts of time
code and “gets lost”.
Turn this ON for faster locating of slave machines in code-only master systems.
13.9 UNTHREAD TIM EOUT (P AGE 9 )
Sets how long the transport must be idle (from 1 to 20 minutes) before the tape is unthreaded
from the head drum. Shorter times trade off less head and tape wear for less convenience, as
it takes slightly longer to go into Play or Record mode from stop if the tape is unthreaded.
Default is 4 minutes.
Procedure: Use the Up/ Down buttons to increment/ decrement in 1-minute increments, or
enter the two-digit number directly with the keypad. Leading zeroes must be entered (e.g.,
for a 3 minute timeout, enter 0 then 3). If both numbers are not entered within 3 seconds, the
display reverts to the previous setting.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
13-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Ut ilit y M e n u , Ch a p t e r 13
13.10 SEARCH ENABLE (P AGE 10 )
Determines how to enable Search mode, where the Jog/ Shuttle wheel is active.
Procedure: Use the Up/ Down buttons to choose between the following:
Normal (default). Moving the Jog/ Shuttle wheel or pressing the Search button (it lights
solid) automatically enables Search mode.
Button. You must press the Search button to enable the Jog/ Shuttle wheel.
13.11 LOCATE BEFORE P LAY (P AGE 11)
When On (default), the master M20 will not play until all ADAT slaves have located to the
master’s tape location. When Off, initiating Play causes the master M20 to play immediately.
Any ADAT slaves that are not at the master tape’s location “catch up” while the master
plays. This parameter is relevant only if ADAT slaves are online with tapes inserted.
Procedure: Use the Up/ Down buttons to choose between On and Off.
13.12 M UTE UNTIL LOCK (P AGE 12)
This allows all ADAT tracks in a multi-machine system to be heard simultaneously when all
machines in the system are locked. When On, M20 masters and slaves will mute their audio
outputs until all M20s in the system have locked. When Off (default), audio will be output
from individual M20s as each one locks, prior to all machines establishing a lock.
13.13 DYNAM IC P UNCH (P AGE 13)
When On and Record mode is pending (section 8.6a), pressing any track record-enable
button toggles between recording and playback. When Off, punching cannot be
accomplished on a per-track basis using the record enable buttons. All tracks must be armed
before record mode is entered.
Procedure: Use the Up/ Down buttons to choose between On and Off.
13.14 TRACK GROUP S (P AGE 14 )
This feature applies only if the M20 is connected to an optional CADI remote control unit.
When Off, CADI Track Groups are ignored (i.e. no Track Groups can be recalled from the
CADI). This prevents accidental group recording or erasing when using a CADI. When On,
CADI Track Groups affect the M20s controlled by the CADI and can therefore be recalled.
13.15 SAVE DATA TO TAP E? (P AGE 15)
Saves the Table of Contents data (TOC) such as location points and names, tape offsets, track
delays, etc. in a BRC-compatible format to the tape’s Data section.
Procedure: Press Yes to save data (the No key has no effect). The tape rewinds immediately to
the beginning while the display shows Preparing to Save. The display then shows Saving
Tape Data. After saving, (approximately 2 minutes) the screen reverts to Save Data to Tape.
13-4
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 13, Ut ilit y M e n u
13.16 LOAD DATA FROM TAP E? (P AGE 16 )
Loads the Table of Contents data from tape into the M20.
Procedure: Press Yes to load data (the No key has no effect). The tape rewinds immediately to
the lead and data sections while the display shows Preparing to Load. The display then
shows Loading Tape Data. After loading, the screen reverts to Load Data from Tape.
13.17 TAP E TYP E (P AGE 17)
Shows the length of an inserted tape (ST60, 120, 160, or 180) and the PAL equivalent (SE90,
180, 240, 260). If no tape is inserted, the display shows Type Unknown.
This screen is display-only. There are no adjustable parameters because the M20
automatically calculates the tape length when each tape is inserted (i.e.
“Calibrating...Standby”).
13.18 ID STATUS (P AGE 18 )
Shows the M20 device ID number. If the M20 is a master (ID 01), the display will also
indicate the number of M20s slaved to the master (up to 15).
This screen is display-only. There are no adjustable parameters.
13.19 USER BITS (P AGE 19 )
This page allows viewing user bits of the tape time code track, incoming SMPTE, or internal
generator.
When the Time Code Track plays back, the display will be continually updated by the user
bits data being read off tape.
If this page is entered while not in Play mode, it will display the last valid user bits read from
tape.
If no time code user bits have ever been read from the current tape, or the tape is playing but
there is no current Time Code Track, the display reads No TC Trk.
This screen is display-only. There are no adjustable parameters.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
13-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Ut ilit y M e n u , Ch a p t e r 13
13.20 ERROR RATE (P AGE 20 )
During playback or record, this screen shows the number of sync block errors per 14 drum
revolutions (280 ms), from 0000 to 6720 (maximum number of errors possible). In any mode
other than Play or Record, the display reads ----. Sync block errors are normally 100%
corrected by the ADAT’s error correction circuitry, but this display acts as a kind of early
warning system. Errors of a properly functioning M20 and tape typically fall in the 0000-
0008 range. All errors are corrected unless the red ERROR indicator flashes in the main
display between the Tape Counter and the Reference Counter; this typically happens when
sync block errors are in the 25-100 range or above. Errors in the hundreds or thousands
indicate severe problems with the tape or with the heads.
If the error rate increases significantly during the course of working with a tape, check
performance with a benchmark or known good tape to see if the tape itself or dirty heads are
at fault. If the tape is dropping out, clone the tape immediately to another M20. If the heads
are dirty, get them cleaned by a knowledgable technician, or as a temporary fix use an
approved dry cleaning tape only.
This screen is display-only. There are no adjustable parameters.
13.21 FRONT P ANEL SOFTW ARE VERSION (P AGE 21)
This screen shows the current front panel software version. If you need to call Alesis tech
support, make a note of this number before calling.
This screen is display-only. There are no adjustable parameters.
13.22 SOFTW ARE VERSION (P AGE 22)
Displays the version and date of the M20’s operating system software. If you need to call
Alesis tech support, make a note of this data before calling.
This screen is display-only. There are no adjustable parameters.
13-6
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAP TER 14
THE LRC REM OT E CONT ROL
The M20 hand-held LRC remote provides the following functions:
·
·
Transport functions: Rewind, Fast Forward, Stop, Play and Record.
Autolocation functions: Locate 1, Locate 2, Locate 3, Locate 4, Set Locate and Auto
Loop
·
Track functions: Auto Record and Rehearse.
These functions are the same as can be accessed from the front panel controls.
The Auto Loop button, which does not exist on the M20 front panel, toggles both Auto Play
and Auto Return functions on and off simultaneously with one button press.
Note: To enable the Auto Play function by itself without the Auto Return function (i.e.
without looping), initiate a deferred play with the Play button ó that is, press any of the
Locate 1 - Locate 4 buttons, followed by the Play button.
To use the LRC, plug it into the Locate/ Play/ LRC Remote jack. If connected to the master
M20 in a multiple ADAT system, the LRC can control the entire chain of ADATs.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
14-1
Download from Www.Somanuals.com. All Manuals Search And Download.
LRC Re m o t e Co n t r o l, Ch a p t e r 14
14-2
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAP TER 15
TUT ORIALS AND AP P LICAT IONS
This chapter gives guidance for entire procedures, assuming a basic familiarity with how the
controls and menus work from previous chapters.
TUTORIAL 1: M ULTIP LE M 20 OP ERATION
OVERVIEW
Because the M20 is ADAT-compatible, it can work together with up to 16 other ADAT-
family machines to provide a total of 128 tracks.
ADAT machines have a sync bus that provides timing information and commands for all
ADATs in a system. When linking multiple ADATs together, the first machine in the chain is
the “master,” and the rest are “slaves.” Each slave locks to the master and synchronizes to
the master machine’s time reference.
Using the 8-channel ADAT Optical Interface, you can also bounce tracks between machines
in the digital realm. The result is a perfect copy (ideal for safety backups and archives) that is
synchronized to the original with single-sample accuracy.
SYNCHRONIZING M ACHINES
Synchronization requires a dual male, 9-pin D connector cable for each slave to be
synchronized. Use only Alesis cables, which are available in three different lengths: 8", 30",
and 30'. Other cables may cause erratic sync performance.
To connect the bus (power must be off), patch one 9-pin D connector cable from the master
sync out to the slave sync in. A slave in a multiple machine system will automatically detect
a master and enter slave mode. With more slaves, connect the slave 2 sync out to the slave 3
sync in, slave 3 sync out to slave 4 sync in, etc.
Power on the machines from first to last, with the CADI remote control (if present) powered
on after all of the ADATs.
After connecting multiple M20s and/ or ADATS together and turning them on, the master’s
display will show “ ID 1” (identifying itself as the number 1 machine in the system). The
second machine will display ID 2, the third ID 3, and so on. The ID order is automatically
assigned according to how the cables are hooked up.
If a slave does not display an ID number on power-up, then it does not see anything
connected to the Sync In jack. Check the cables and connections.
To check a machine’s ID, go to Utility page 18.
AUT OM AT IC ID RENUM BERING
Machines in a multiple ADAT system will renumber their IDs if more M20s or ADATs are
connected later. Example: Suppose in a 3-ADAT system that machine 1 is the master, and
machines 2 and 3 are slaves. If you turn on only machines 2 and 3, machine 1 will not be
ALESIS M 20 REFERENCE M ANUAL 1.0 6
15-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Tu t o r ia ls a n d Ap p lica t io n s , Ch a p t e r 15
active, so machine 2 decides it’s the master (ID 1) and machine 3 the only slave (ID 2). If you
then turn on machine 1, the machines will renumber themselves so that machine 1 becomes
the master (ID 1), and machines 2 and 3 become the slaves (ID 2 and 3, respectively).
Sync signals cannot pass through a machine that is turned off. For example, if machines 1
and 3 are turned on but machine 2 is turned off, machine 3 will not slave to machine 1
because the sync signal cannot pass through machine 2.
M ASTER/SLAVE INT ERACT ION
Pressing any of the Transport, Auto Rec, Auto Input, Pitch, All Input, or Locate buttons
automatically triggers the same functions on the slave machine(s).
To minimize confusion, Alesis recommends initiating all operations from the master,
including transport control functions. When you press Play on the master, the slave(s) will
locate to the same time code point and begin playing once sync is achieved.
Pressing Eject on the master ejects all slaves’ tapes as well. To eject only the master’s tape,
press and hold Peak Clear, then press Eject on the master.
When recording or punching in on the slaves, initiate recording on the master but do not
record-enable any master tracks (unless, of course, you need to record tracks on the master).
Any record-enabled slave tracks will go into record, while the master will simply play. This is
why record enable is an independent function for each slave.
There are two other functions where the slave(s) act independently:
·
·
Formatting is initiated independently on each slave, however, simultaneous formatting
on all slaves is possible.
Digital Input is independent for the slave(s) as you may want to record via the analog
inputs on some machines and the digital inputs on others.
ACHIEVING LOCK
In a multiple-ADAT system, the slaves will “chase” the master (the M20’s Chase indicator
lights) and can only enter record once they are locked. Audio will not appear at an ADAT’s
outputs until it is locked, as shown by a lit Locked indicator. For the fastest chase-lock
performance in a multi-ADAT system, use the Locate points when possible to go to different
points on the tape.
INDEP ENDENT SLAVE M ODE
If a slave M20 is taken offline (Online button is off), its transport can be controlled
independently. Example: Press Play on the offline slave and it will play, but the other slaves
and master will not respond. When the slave in placed online again, it will respond to
transport commands from the master.
15-2
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 15, Tu t o r ia ls a n d Ap p lica t io n s
FORM ATTING M ULTIP LE TAP ES
Formatting works similarly to formatting on a single ADAT, however there are some
considerations unique to formatting multiple tapes. For more information on formatting, see
Chapter 4.
M ASTER FORM AT ENABLED, COM P LETE FORM AT
If the master’s Format indicator is on, performing a complete start-to-finish format, and the
slave tape is not already formatted:
·
·
If the slave’s Format indicator is on, the slave rewinds to the start of the tape and does a
complete format along with the master.
If the slave’s Format indicator is off, the slave rewinds to the start of the tape and plays,
but the TIME counter reads “noFO” (no format) while flashing the FORMAT indicator.
If the master’s Format indicator is on, performing a complete start-to-finish format, and the
slave tape is already formatted:
·
·
If the slave’s Format indicator is on, the slave rewinds to the start of the tape and does a
complete format.
If the slave’s Format indicator is off, the slave rewinds to the start of the tape and plays
in sync with the master.
Any record-enabled channels will start recording at time 0:00:00.00.
M ASTER FORM AT ENABLED, FORM AT EXT END
If the master’s Format indicator is on, you are extending the format, and the slave tape is not
formatted, the slave plays, but its Time counter reads “noFo” (no format) while flashing its
Format indicator.
If the master’s Format indicator is on, you are extending the format, and the slave tape is
formatted:
·
·
If the slave’s Format indicator is on, the slave autolocates to the same time as the master,
then format extension begins with the master.
If the slave’s Format indicator is off, the slave autolocates to the same time as the master
and plays or records in sync.
To properly extend the format, the master and slaves should be playing in sync (i.e., the
Locked icon should be on) before punching into format record.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
15-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Tu t o r ia ls a n d Ap p lica t io n s , Ch a p t e r 15
M ASTER FORM AT DISABLED
If the master’s Format indicator is off, you initiate record anywhere in the tape, and the
slave’s Format indicator is off:
·
·
If the slave tape is unformatted, the slave plays, but the Time counter reads “noFo” (no
format) while flashing the Format indicator.
If the slave tape is formatted, the slave autolocates to the same time as the master and
plays or records in sync.
To properly punch in, the master and slave should be in sync before punching. Otherwise,
the master will punch in immediately, but the slaves won’t punch in until sync is achieved.
M ASTER FORM AT DISABLED, FORM AT EXT END
If the master initiates recording from the audio portion of the tape and the slave’s Format
button is on:
·
·
If the slave tape is unformatted, the slave plays, but the Time counter reads “noFo” (no
format) while flashing the Format indicator.
If the slave’s tape is formatted, the slave autolocates to the same time as the master, then
format extension begins.
If the master initiates recording from the start of the tape and the slave’s Format button is on,
start-to-finish formatting begins regardless of whether the slave tape is formatted or not.
15-4
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 15, Tu t o r ia ls a n d Ap p lica t io n s
TUTORIAL 2: M AKING DIGITAL BACKUP S
You can create safety copies of M20 tapes by copying all eight tracks to another M20 (or
ADAT-compatible machine) via the digital bus.
Alesis recommends creating a backup whenever you have irreplaceable material on tape.
Synchronizing two machines together via the 9-pin sync bus allows for making sample-
accurate copies, referred to the internal time code. This is preferred. Without sync, you can
simply start recording on the slave and play back from the master. This faithfully copies the
audio information, but in all likelihood there will be a timing offset between the two tapes.
Here’s the procedure for creating a backup tape.
Action
You do...
You see...
Synchronize the master and
slave
Connect a male/ male, 9-pin D
connector cable between the
master Sync Out and the slave
Sync In
The master becomes ID 1 and the
slave ID 2 on power-up
Establish digital audio
connection
Connect a fiber optic cable
between the master ADAT
Optical Out and the slave
ADAT Optical In
No visible change on machine
Load machines with tapes
Insert the tape to be backed up Eject lights go off
into the master, and a blank or
formatted tape into the slave
·
·
To make a 20-bit backup, both machines must be Type II with tapes formatted in 20-bit mode.
If the tape is unformatted, put the slave into Format mode (see Chapter 4). If the tape is partially
formatted, the slave tape needs to have its format extended (see section 4.5).
For safety’s sake, write-protect the tape to be copied by breaking off (or sliding open) the tape’s
write protect tab.
·
Return both machines to a
common start point
Press the Locate 0 button
Both Time counters read 0:00:00.00
Enable optical inputs
Select ADAT Optical Digital
Digital Source block shows ADAT
Source on both the master and Optical
slave M20
Select digital as the Input
Press Input Select then press
A “D” will be displayed beneath
Select source on both machines All Input
all 8 channel meters
Enable all slave tracks for
recording
Press all slave Record Enable
buttons
The Record indicators for all slave
tracks will flash
Be sure that the Record Enable buttons are switched off for tracks 1—8 of the master M20!
Initiate tape cloning
Press both Play and Record on Both machines start, Record
the master
Enable indicators on slave
machine light solid
End backup
Press Stop on the master after
backup is complete
Both machines stop
ALESIS M 20 REFERENCE M ANUAL 1.0 6
15-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Tu t o r ia ls a n d Ap p lica t io n s , Ch a p t e r 15
DEALING W IT H DAM AGED TAP E
If a tape is in very bad condition, it may be difficult to copy it from the master to a slave. If
there are so many errors that the M20 momentarily loses sync during playback, all slaves will
be taken out of record automatically. In this case, put the new tape into the master, the
damaged tape in the slave, and copy from the slave to the master.
M AKING A 16 -BIT COP Y FROM A 20 -BIT M AST ER
With over 100,000 ADAT 16-bit Type I machines in use, you may need to trade tapes with
someone who owns an older machine. You can still with the M20 in 20-bit Type II mode, and
make Type I “clones” for use in older machines. You can also use an older Type I machine as
a slave to an M20, using the same procedures and hookup listed earlier in this chapter.
Alesis recommends creating 16-bit “clone” tapes using dithering, a process that provides
better apparent resolution than standard 16-bit copies (however, do not add dither if the
material will be re-dithered later on). The process is the same as making a standard backup,
except that you select a dithered 16-bit output from the master, as described in section 13.1.
15-6
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 15, Tu t o r ia ls a n d Ap p lica t io n s
TUTORIAL 3: RECORDING DIGITAL AUDIO FROM
OTHER SOURCES
Recording digital audio onto the M20 from a source other than an ADAT-compatible device
requires a digital audio interface, like the Otari UFC-24 or Kurzweil DMTi, or inserting an
Alesis EC-1 AES/ EBU interface into the M20’s Expansion Card slot. These convert other
digital audio formats to the Alesis Optical format. The ADAT-PCR card can also output
audio recorded into a hard disk editing program as ADAT Optical format-compatible
signals.
When recording digital audio into the M20 from another ADAT-family device in a multiple
ADAT system, the M20 recording the audio is already synchronized with the other machines
because all slave machines are automatically set to External Clock mode. They follow the
master precisely.
When recording digital audio from some other source, the M20 must synchronize its clock to
the incoming digital audio. How this is done depends on whether you are using a single M20
or a multiple ADAT system. We will assume an ADAT Optical interface cable is carrying the
incoming digital audio, perhaps from an ADAT-PCR card.
With a single M20, connect the incoming Optical Out (e.g., from the ADAT-PCR card) to the
M20’s Digital In using a single fiber optic connector. Press the M20’s Clock Source button,
and set its clock source to Optical. The M20 will synchronize to the clock information present
in the Optical Out.
In a multiple ADAT system, you have two choices: synchronize the digital audio source to
the ADAT system (as described above for a single ADAT), or sync the ADAT system to the
digital audio source.
If the source does not have a clock input (i.e., it cannot sync to an external clock), you need to
choose the latter option. Connect the Optical Out to the master ADAT’s Optical In, whose
Optical Out already connects to the next slave, and so on. Set the master’s Clock Source to
ADAT (or I/ O card if using the AES/ EBU interface). If no digital audio clock is detected, the
master M20 will continue using its own internal clock. When the master receives digital
audio (and therefore, a digital clock), the master M20 will sync to the incoming digital clock.
DIGIT AL CLOCK CONSIDERAT IONS
Switching between the M20’s two internal clock sample rates (48 kHz and 44.1 kHz), changes
the reference used for computing tape location. Therefore, the same tape location will appear
to have two different time addresses depending on the selected sample rate.
Since the M20 cannot detect an external clock’s sample rate, you need to choose the reference
base the M20 should use to calculate tape position while syncing to the digital clock. Select
either 48 kHz or 44.1 kHz with the Sample Rate button.
If you hear clicks in the audio after recording from a digital source, either the Clock
Source is set incorrectly, or there is some other timing problem. Most commonly,
clock problems are the result of trying to use SMPTE Chase and receive digital input
simultaneously, where the digital source itself is not chasing the same SMPTE or
clock reference as the M20, or the SMPTE isn’t referenced to digital clock. There
must be one, and only one clock source in a multi-machine system.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
15-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Tu t o r ia ls a n d Ap p lica t io n s , Ch a p t e r 15
TUTORIAL 4 : COM BINING M 20 S AND ADATS
M 20 TRANSP ORT SP EED
The M20’s transport speed is much faster in engaged mode than the original ADAT. Because
of this and other unique features, make the M20 the master (ID 1) and any ADAT(s) should
be the slave(s).
When locating, the M20 will locate to a specific tape position, stop, and wait for the ADAT(s)
to catch up. Therefore, until you need more than 8 tracks, don’t put any tape(s) into the slave
unit(s) so that the M20 won’t have to wait for the slave(s) to locate.
SAM P LE RATE VS. P IT CH CONT ROL
The M20’s Sample Rate function, which allows choosing between 48 kHz or 44.1 kHz
sampling rates, was not directly available on the original ADAT. This function also allows
selecting a digital clock for applications involving the recording of digital audio from a non-
ADAT source.
The M20 writes sample rate information when formatting a tape, so that it automatically
knows a formatted tape’s sample rate (even though either rate may be used).
Example: When playing back a tape formatted at 48 kHz with the sample rate set to 44.1 kHz,
the 44.1 indicator will flash, to indicate that you are using 44.1 kHz but it isn’t the original
sample rate used when the tape was formatted. The same goes when you play back a tape
formatted using 44.1 kHz with the sample rate set to 48 kHz; the 48 kHz indicator will flash.
The M20 Pitch Controls supplement the sample rate selection. With the original ADAT, you
had to pitch down a tape to play back at a 44.1 kHz sample rate. If you play back a tape that
was formatted on an original ADAT, it will not have any sample rate information written on
it. The M20 will automatically select the 48 kHz setting. If you had been pitching-down such
a tape to play at 44.1 kHz, you must press the Sample Rate button to manually change the
M20’s sample rate to 44.1 kHz.
INP UT M ONIT ORING
The original ADAT was designed so that when monitoring a track’s input signal, you heard
the actual analog input ó the signal did not pass through the A/ D and D/ A converters.
There was an advanced feature, accessed by holding Set Locate and pressing All Input, that
allowed monitoring after the converters. This allowed hearing exactly how the signal would
sound when played back from tape.
The M20 monitors the input signals through the converters at all times (unless overridden as
described in section 8.6d). This creates a minuscule delay as the digital audio passes through
the converters’ buffers. If you were to listen to both the original signal on your mixer and the
tape return of the same signal coming back from the M20, the M20’s delay would cause some
phase cancellation when combined with the original signal. Therefore, it is important that
you either monitor the original signal or the tape’s input signal on your mixer, but not both.
15-8
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 15, Tu t o r ia ls a n d Ap p lica t io n s
P OLARIT Y DIFFERENCES
The original ADAT inverted the polarity of the signal being recorded on tape, then flipped
polarity again before going to the output jacks. As a result, the output was the same polarity
as the input, so no phase problems were possible when using a single ADAT or a multiple
ADAT system.
However, neither the digital input nor the digital output was inverted. Therefore, if one
transfers the ADAT’s digital audio data to a DAT machine or hard disk recording system
(using the AI-1 or a similar digital interface), the audio output from the other device would
likely be out of phase with the ADAT, since it probably does not invert the analog signal
after its D/ A converters. Although this in itself will usually not be a problem, it may cause
some confusion if multiple correlated audio signals are combined from multiple sources
since there is a possibility that signals could become out of phase.
To prevent this from occurring, with the M20 the polarity remains constant from the analog
to digital, and back to analog, domain. Like the original ADAT, the result from one machine,
or multiples of the same machine, is the same: The input to output phase is correct.
However, if two cloned tapes (copied digitally either with ADATs, M20s, or both) are played
back in sync on both an ADAT and an M20, the outputs of the two machines will be out of
phase relative to each other. Since it does not usually serve any practical purpose to play the
same signal from two different tapes with two different model machines simultaneously, this
should not present a problem for you. This design improvement is only mentioned here to
explain this possible situation should you happen to experience it.
Possible problem: Let’s say you had been using a multiple ADAT system and you recorded a
stereo signal across two machines (a stereo drum recording on tracks 8 and 9), where there is
a common element to each track (i.e. center signal). If you replace one of these machines with
an M20, the result would be that the track being played back on the M20 will be out of phase
from the track played on the ADAT, canceling the center signal.
Here are some possible solutions:
·
·
Use a phase switch on your mixer (if your mixing board provides this) to invert the
phase of the problem track to compensate.
Wire your patchbay to reverse the input and output polarity of the M20s in the system,
but use standard cables on the ADATs in the system. This is recommended only for
studios where master tapes will be exchanged between units or sent out of house.
·
·
Digitally bounce one of the stereo tracks to the other ADAT so that both sides play back
from the same machine.
Most importantly, plan recording sessions so that stereo tracks reside on the same
physical tape in a multiple ADAT system.
Note that if you overdub over an older ADAT tape in an M20, that track will now be in
phase.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
15-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Tu t o r ia ls a n d Ap p lica t io n s , Ch a p t e r 15
TUTORIAL 5: SETTING UP INP UTS
The M20 offers unparalleled flexibility in terms of setting up inputs for recording: signals can
come from analog sources, digital sources (ADAT optical or from optional AES/ EBU cards),
or a combination of the two. As a result, it is important to understand the proper procedure
for selecting the right sources for the right inputs. The following gives an overview of the
process; for more details, see Chapter 6.
1
2
If you are going to be using any digital sources, specify ADAT Optical or I/ O Card using
the Digital Source button.
Decide which track pairs will accept analog inputs, and which will accept digital inputs.
To do this, first press the Input Select button. Each push of one of a track pair’s Track
Input Enable buttons toggles between analog and digital (from the digital source selected
in step 1). A small “D” or “A” indicator lights under the VU meters to show the selected
input source.
3
4
Set up the input routing for the analog signals by pressing the Input Routing button. This
function determines which inputs go to which tracks. For more details, see section 6.4a.
Set up the input routing for the digital signals. Press the Input Routing button twice (or
only one more time if you are already in the analog routing page). There can be a simple
one-to-one correspondence (e.g., input 1 goes to track 1, input 2 goes to track 2, etc.) or
tracks can be reassigned.
5
To reassign tracks, when in the digital routing page, press the Input enable buttons for
the desired digital source tracks. When you record-enable tracks, the lowest-numbered
source track will be assigned to the lowest-numbered record enabled track; the next-
lowest-numbered source track will be assigned to the next lowest-numbered record
enabled track; and so on.
Your inputs are now set up to record from the desired source tracks.
15-10
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 15, Tu t o r ia ls a n d Ap p lica t io n s
TUTORIAL 6 : UP DATING M 20 SOFTW ARE
The M20 accepts software updates via MIDI. This allows Alesis to offer improvements and
changes to the operating system without requiring the unit to be professionally serviced.
The fastest way to update the software is to go to the Alesis web site
(http:/ / www.alesis.com). Go to the “Software” section, and locate the area containing M20
software updates.
Files are in Standard MIDI File format, and can be downloaded as .hqx (binhex encoded)
files for Macintosh computers or as .zip (compressed) files for Windows based computers.
WinZip will decode zipped files. Mac users can use Stuffit to decode binhexed files.
After downloading, decode and import the file into a MIDI sequencer or other device
capable of playing back MIDI files. It should be able to handle fairly long sysex dumps.
Before plugging the MIDI cable from your MIDI sequencer to the M20 MIDI in, first check
the output with a MIDI activity indicator. You want to make sure that your MIDI device is
indeed capable of transmitting the data before trying to load it into the M20. Loading
incomplete or corrupted data into the M20 could require a trip to the dealer if there is a
problem transmitting the sysex to the M20. As a precaution, you may wish to save the
existing M20 software in your unit to a MIDI file as a backup in case the downloaded version
became corrupted during the download or decoding process. Once you verify that your
MIDI device is sending data properly, proceed.
For example, if you import the file into Cakewalkä , a dialog box appears that says “File has
System Exclusive auto send banks. Send them now?” Click on yes. With Mac sequencers, you
may need to press Play after importing the sequence, or use the Freeloaderä utility (also on
the Alesis web site), to start transmitting the sysex. The software updating process will take
about 6 minutes to complete.
Software updating has been tested with Cakewalkä on the PC, and Cubaseä and Performerä
on the Mac. Other programs are likely to work as well.
If you do not have access to the web or to MIDI sequencers, contact your Alesis dealer about
alternate ways to update your software. A simple MIDI connection from another M20 with a
new software version can update your unit in about 12 minutes.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
15-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Tu t o r ia ls a n d Ap p lica t io n s , Ch a p t e r 15
TUTORIAL 7: USING THE M 20 W ITH UNBALANCED
INP UTS AND OUTP UTS
It is possible to use unbalanced signals with the M20, however you will need adapters like
the following:
Note that it is probable that unbalanced lines will not have enough level to drive the M20 to
full scale, and will require preamplification, or the input trimmers of your M20 must be reset
to accommodate lower levels. The standard factory setting is +19 dBu = 0 dBFS (just before
clipping). A mixer with a standard output of +4 dBu at 0 VU should light “-15 dB” on the
M20’s meter.
15-12
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAP T ER 16
M 20 SM P TE
SYNCHRONIZAT ION OVERVIEW
This chapter is an overview of the M20’s SMPTE time code features, in addition to the basics
covered in Chapter 11. Before you design a synchronization system, and particularly if you
have not used time code before, please read this chapter carefully. It is impossible for any
manual to cover all the possible combinations of synchronizers, decks, automated mixing
consoles, sequencers, and video editors; but a solid understanding of synchronization
principles will help you be successful no matter what equipment you plan to combine with
the M20.
16 .1 SYNCHRONIZATION BASICS
When machines are synchronized, they move together at exactly the same speed, passing
through corresponding locations. To do this, there must be some kind of time marker
recorded continuously on each machine, along with the audio and video tracks. One
machine must be designated the master or controlling machine, and others are considered
slaves. Each slave machine must have the intelligence to compare the incoming time signal
from the master machine to its own location, and speed up, slow down, or locate to match
the master’s position. When it’s doing this, this is called chase mode.
M ASTER OR SLAVE?
The M20 may be used as master or slave because of its built-in time code synchronizer.
When it’s a master, you command the entire recording system by using the transport
controls on the M20 (or CADI). The M20’s SMPTE OUT jack will issue SMPTE time code
(depending on the parameters you set) to video or other audio decks. If they are also
equipped with synchronizers and are in chase mode, they will follow the M20 system’s lead.
When the M20 is used as a slave, it receives time code from the master (a video deck, hard
disc recorder, or edit controller) and moves to match it, depending on the M20’s time code
and SMPTE Chase parameters. On a slightly higher level, it may also receive direct
commands (play, rewind, record etc.) from a controller via MIDI Machine Control or (when
2.0 software becomes available) via the RS-422 port.
DIGIT AL TIM ING REQUIREM ENT S
In addition to SMPTE time code synchronization, digital audio recording has its own
synchronization needs. When recording from a digital source (either ADAT Optical or the
optional EC-1 AES/ EBU card), the M20’s speed must match the flow of digits as they come
in. This can lead to certain problems that analog recorders did not face.
For example, suppose you have the M20 in SMPTE Chase mode, following time code and
video clock from a VCR. You want to record a sound effect from a CD player digitally into
the AES/ EBU card at a certain cue. But at the cue, when you press PLAY on the CD player,
you notice clicks and pops in the audio. What happened?
ALESIS M 20 REFERENCE M ANUAL 1.0 6
16-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SM P TE Syn ch r o n iz a t io n Ove r vie w , Ch a p t e r 16
The CD player’s digital clock is uncontrolled. The M20 normally would automatically
synchronize to an incoming digital signal, but in this case it’s following the video which is
traveling at its own speed. Since a slave can’t follow two masters, the slight timing
discontinuities appear as clicks and pops as samples are lost. Depending on your equipment,
there may be several ways to solve this problem, but in any case the solution will involve the
following principle:
16 .2 THE ONE CLOCK P RINCIP LE
To prevent synchronization problems, every piece of equipment in the system must
ultimately refer to the same clock. There may be only one master at a time, and all
others must follow it. If different types of clock are required by different pieces of
equipment, all slave clocks must be derived from or synchronized to one master
clock. For example, there must be exactly one frame of video for every SMPTE time
code frame, and exactly the right number of digital samples for each frame.
If you violate the one clock principle in your system design or operation, the consequences
will range from the severe (ticks and pops in the audio, sudden fast-forwards or jumping out
of record) to the less obvious (an increasing drift in the lock between different machines as
they travel).
16 .2A HOUSE SYNC
For a system to operate smoothly, you need all your audio gear taking “sonic pictures” and
your video gear taking pictures at the same rate. Professional video houses achieve this by
having a black burst or house sync generator with a clean, steady wow-and-flutter-free video
signal that is distributed to all VCRs in a building. Several companies make these kinds of
generators, and for complex systems a unified video/ word clock/ AES black generator (such
as MOTU’s Digital Timepiece™) may be the best solution. Depending on your system, you
would connect house sync to the M20’s Video In or Word Clock In jacks.
16 .2B “GENLOCKED” TIM E CODE
A solid and steady video or digital reference by itself is not enough, because only SMPTE
time code carries the actual data of hours:minutes:seconds:frames required for a chase-lock
system. A common mistake is to generate “wild” time code, not referenced to the video or
digital signal. In other words, your time code generator must start its frame message at the
exact same time that the video signal is starting its scan of the frame and the first sample of
the digital audio is going to the converters.
Just because it’s time code doesn’t mean it’s going at the same rate as everything else in the
system. By common standards, it may seem right, but even small errors add up when you’re
trying to divide each second into 48,000 slices. This brings to light another important
principle: understanding the difference between location references and clock references.
16-2
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 16 , SM P TE Syn ch r o n iz a t io n Ove r vie w
16 .3 REFERENCE COUNTERS VS. CLOCK SOURCES
A wristwatch indicates the passage of time in two ways. One is the face of the watch, which
gives the information of hours, minutes, and seconds. The other is the “ticking” of the watch
several times per second. Conceivably, you could always know what the time is by looking
at the face of the watch one time, then counting how many ticks had elapsed. In video, the
“ticking” is provided by the edge of the video fields (approximately 60 per second), and in
digital audio by the number of samples (48,000 per second).
When locking the M20 to video or another digital recorder, it’s important to understand the
distinction between the location reference, and the reference clock. The row of buttons below
the M20’s main display allow you to set these two clocks independently from each other,
because they have slightly different functions.
16 .3A LOCAT ION REFERENCE
Location reference describes the actual position (or address) of each device. This is usually
determined by the SMPTE time code coming from each machine being synchronized. Unlike
reference clock, location reference always knows exactly where it is because the time
reference information (hours/ minutes/ seconds/ frames) is embedded in the code.
The ADAT format used in the M20 has two different location references recorded on tape:
1. ABS time is the sample-accurate time code written on every formatted ADAT tape.
Every ADAT machine can read ABS time, which counts the number of minutes and
seconds from the head of the tape, starting at -00:05 (after 15 seconds of Lead and 2
minutes of Data), continuing to about 40 minutes at the end of a typical ST-120 tape.
There is never a break or interruption in the ABS time of a properly formatted ADAT
tape, and it always starts at zero. It is the ABS time which is transmitted via the ADAT
Sync to all ADATs in a multi-ADAT system so they can sync to the ID1 ADAT.
2. The TC track is a read/ write SMPTE time code track recorded in a separate subcode area
from the ABS time. The TC track is only readable in ADAT machines with TC track
capability (currently, the Alesis M20, the Studer V8, and the Fostex RD-8). Unlike ABS
time, the TC track can be blank, have interruptions, start at any
hour/ minute/ second/ frame desired, and/ or be discontinuous (i.e., jump in values) if it
was recorded that way. In a typical multi-ADAT system connected via the ADAT Sync,
only the lead (ID1) M20 uses its TC track as a location reference. The ADAT slaves (ID2
or higher) do not know the master’s SMPTE time; they only know the ABS time and
chase to it.
The M20 allows you to select either of these references as a Chase Reference or a Tape
Counter at any time.
16 .3B REFERENCE CLOCK
Reference clock is the “heartbeat” of your studio. It is a constant, steady “ticking”, without
any other information, connected to all synchronizer systems in your studio. Black burst
video and word clock are both forms of reference clock. Reference clock has no regard for
time code position, but instead is concerned only with making everything travel at exactly
the same speed. In a digital audio-to-video synchronization system, all elements (the SMPTE
time code, the digital sample rate, and the video frame rate) must advance in lock-step with
each other.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
16-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SM P TE Syn ch r o n iz a t io n Ove r vie w , Ch a p t e r 16
Another illustration of the need for reference clock comes from the video world. In order to
make clean edits between several video recorders, all video sources must display their
pictures at the same rate with the frame edges occurring at exactly the same time. If each
VCR were left to run freely on its own, the transports would move at slightly different rates,
the respective pictures wouldn’t line up, and we’d see a black bar (the vertical interval) roll
through the picture every time an edit was made. By referencing all VCRs to house sync,
they all start each frame simultaneously.
In a typical 3-deck video editing situation, note that the location references are usually
intentionally different, but all reference clocks are unified: a shot at 02:30:44:00 may be
followed by a segment whose location is 14:02:00:15 (and so on), but the master deck
recording video and the two slave decks sending video all start their pictures at the top of
the video screen simultaneously.
This introduces another concept important to successful and flexible synchronization: the
offset.
16-4
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 16 , SM P TE Syn ch r o n iz a t io n Ove r vie w
16 .3 OFFSETS IN THE M 20
An offset is an intentional difference in location between decks. In the simplest situations,
offsets are not required: when it’s 2 o’clock on the master, it’s 2 o’clock on all the slaves. But
more often, tapes were recorded at different times, in a different order, and now must be
edited together at a particular sync point.
In particular, in the M20, there are two different Chase References which may provide time
code: ABS time and Tape (SMPTE) time code. Most of the time, these two time codes will
not numerically match (although they should advance at exactly the same rate). You may
use offsets to transform any ABS or SMPTE location to any time code desired, depending on
the needs of your project.
Example: While ABS time always begins at 00:00:00 on every ADAT tape, it is
customary for SMPTE time code to start no earlier than 00:58:00:00. You can set the
ABS offset so that the internal generator will issue SMPTE time code at 58 minutes
after midnight at the actual ABS location zero.
There are three different places to set offsets in an M20 system:
16 .3A SM P T E CHASE OFFSET
This is set in the first page of Edit SMPTE Chase mode (see section 11.6a).
The SMPTE Chase Offset is used to offset the M20 from incoming time code. It is added to
the ABS time to equal the SMPTE Tape Counter display. If the M20 is slaving to an external
time code source, the SMPTE Chase Offset will be added to the Chase Reference (either ABS
or Tape TC) to offset the M20 from the incoming master time code.
Example: If the SMPTE Chase Offset is 4 hours, and the Chase Reference is ABS time,
and the Timecode Source is External, when the SMPTE IN reference counter is
04:30:15, the M20 will chase to ABS location 00:30:15.
Note: The Tape Counter SMPTE display is always based on ABS Time plus the SMPTE Chase
Offset, even when the Chase Reference is set to Tape TC. This may lead to
confusion in applications where Tape TC was recorded without reference to the
ABS time for some reason. But despite the “SMPTE display” not matching the
incoming time code, it does synchronize and chase to the Tape TC plus the SMPTE
Offset. To avoid confusion, turn the Tape Counter to ABS.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
16-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SM P TE Syn ch r o n iz a t io n Ove r vie w , Ch a p t e r 16
16 .3B INT ERNAL GENERAT OR ABS OFFSET
This is set in INT GEN EDIT mode, pages 2 and 3 (see section 11.7c).
This is used when you want to issue time code from the M20 based on the ABS time plus an
offset, usually to record on the TC track of the M20 and/ or an external recorder. This is
most often used when pre-striping tapes, or when the M20 is a master in a system.
Example: If the ABS offset in INT GEN is set to 12:00:00, and INT GEN and the TC
INPUT switches are on, the M20 will generate SMPTE time code starting at 12:00:00
at ABS time 00:00:00. To see this clearly, set the Tape Counter to ABS and the
Reference Counter to INT GEN.
When you rewind or fast forward the M20 in this mode, it will not issue time code from the
internal generator until you enter Play mode again (at which point the INT GEN display will
immediately “catch up” to the ABS time plus the offset).
16 .3C TAP E OFFSET
Tape Offset in the M20, as in all ADATs before it, is designed for offsetting one ADAT from
another, usually for the purposes of digital copying one section of tape to a different location.
In a multi-ADAT system, the Tape Offset allows any ADAT to be ahead of or behind of the
master time location. But the Tape Offset button is not used for setting an offset from
incoming SMPTE Time Code: that is set in the first page of the SMPTE Chase menu.
Tape Offset in SMPTE Chase mode is exclusively for offsetting slave offsets from the ID1
ADAT.
If you press Tape Offset on the top ID1 ADAT, it turns on Tape Offset on all ADAT slaves
and sends them a message setting their Tape Offsets so they will be ahead of or behind the
top ADAT by the specified amount. This overwrites whatever the slaves’ Tape Offsets were
previously.
If the Tape Offset of a slave (ID2 and above) ADAT is turned on, only that particular
machine will be offset. Each slave may have its own tape offset (but, as noted above, if you
turn Tape Offset on the master machine, the slaves’ offset values will be overwritten).
If the top ID1 ADAT is in SMPTE Chase mode, and has a Tape Offset, it will not affect the
relationship between the top ADAT and the incoming time code. (Effective with Version 1.01
software.) Any ADAT slaves below the master will be offset from the master, and from
incoming time code, by the specified amount.
Example: If the top M20 is in SMPTE Chase mode, with ABS as the Chase Reference, a
SMPTE offset of -1 hour, and a Tape Offset of -10 minutes, incoming time code of one
hour will cause the master to chase to 01:00:00 SMPTE time (00:00 ABS time). The
bottom M20s or ADATs will be at 01:10:00 SMPTE time (10:00 ABS time), as long as
their Tape Offset buttons are lit.
If a slave ADAT is offset to a point out of tape range (for example, if the master is at a point that puts
the slave at the LEAD section at the beginning of its tape), the message “Tape Offset Standby” will
appear. When the master advances to a point where the slave is past 00:00:00 ABS time, audio will
start automatically.
16-6
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 16 , SM P TE Syn ch r o n iz a t io n Ove r vie w
16 .4 SM P TE TIM E CODE RATES AND TYP ES
SMPTE time code is the universal standard for transmitting location reference in audio and
video systems. SMPTE is primarily a location reference, though it may also be used as a
reference clock if necessary, because its signal is sent on a pulse-width modulated audio tone.
It transmits time as hours, minutes, seconds, and frames; by looking at the tone it may be
divided into subframes. The M20 can read and generate SMPTE time code in any one of
several formats.
The Society of Motion Picture and Television Engineers agreed on several code rates to
accommodate the needs of film and television work all around the world, which already had
different television standards. The frame rate of television in the United States was
originally 30 frames per second (fps) for black-and-white monochrome transmission, which
slowed for technical reasons to 29.97 fps at the advent of color television (the NTSC
standard). The standard television frame rate in Europe and many other parts of the world
using the PAL/ SECAM standard is 25 fps, and the standard film rate worldwide is 24 fps.
When transferring between American television and film (the telecine process), a slight 0.1%
variation on the frame rate is necessary in some situations. This is called pull-up and pull-
down.
16 .4 A DROP FRAM E
In addition to the different SMPTE rates, there is a need to number or count the frames
differently in NTSC systems. The two slightly different speeds (29.97 vs. 30) leads to a
problem: if the SMPTE time code numbers 29.97 frames as if there are 30 per second, a
progressive error occurs. After half an hour, the SMPTE reader will show “00:29:58:06”
instead of “00:30:00:00”– almost two seconds short of real time. By using the “drop frame”
frame counting feature of SMPTE time code, certain numbers in the frame sequence are
skipped so that real time and SMPTE time agree. Note that this is only a numbering
convention: frames are not actually lost, they are just counted differently. An analogy is
when we add February 29 to our calendars during leap years to keep our counting of days in
sync with the seasons of the year.
SMPTE time code carries a bit identifying the code as drop or non-drop code, so all receivers
will know the counting method being used. If you are trying to locate to a particular frame
(i.e., the 00 or 01 frames at the start of most minutes) and it “doesn’t exist”, it’s because the
code is drop frame.
Tip: Drop-frame code is typically used with the 29.97 fps rate, and non-drop with the 30
fps rate. Most music projects use 30 non-drop if they’re not syncing to NTSC
television. Use non-standard codes (29.97 non-drop, and 30 drop frame) under
special circumstances. Check with the other people on your project to find out the
best rate to use.
16 .4 B AUT O-DETECTION OF SM P TE RATES
When the M20 is set to synchronize to an external SMPTE source, it will automatically detect
if the incoming time code rate is 24 fps or 25 fps. It will also automatically detect if the
incoming code is drop frame or not.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
16-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SM P TE Syn ch r o n iz a t io n Ove r vie w , Ch a p t e r 16
But since the speed difference between 29.97 and 30 fps is small (only .1%), the M20 cannot
detect that fine difference in frequency and will default to the last selected non-drop fps rate
(which may not correlate to the incoming time code). If your project is supposed to run at
29.97 fps, make sure the SMPTE rate is set properly. If necessary, change the SMPTE rate
using the SMPTE Rate button. Otherwise, your audio tracks will drift slightly from the
audio and/ or video material the M20 is chasing.
All tapes should be clearly labelled with the time code type, speed, and start time. This
will save you time and avoid confusion.
The most challenging synchronization projects are those that cross media boundaries. For
example, a project may be shot on film (24 fps), transferred to NTSC video for editing (29.97
drop frame), and transferred to PAL video (25 fps) for overdubbing in Europe. If you’re
involved in such a project, make sure that those in charge have experience with such
transfers and have specified exactly what they require. Film-to-video transfers involving
digital audio need special pull-up and/ or pull-down sample rates. In every case, the
principle of “one clock” applies to avoid weird pitch and tempo changes and falling out of
sync.
16 .4 C VITC (VERTICAL INT ERVAL TIM E CODE)
SMPTE time code can be written in the vertical interval between frames of a video signal;
this is called VITC. The advantage of VITC is that the video deck knows what frame it is
sitting on even when it is in pause mode or moving at too slow a speed to read its standard
LTC (linear time code track).
The M20 does not have the necessary electronics to read VITC appearing at its Video
Reference Input. In most cases, VITC-encoded tapes are also striped with SMPTE on a linear
track, which should be plugged into the SMPTE In jack of the M20. If the tape only has
VITC, obtain an interface (such as Mark of the Unicorn’s MIDI Time Piece AV®) capable of
converting it to a standard audio SMPTE signal for plugging into the M20.
16 .4 D M TC (M IDI TIM E CODE)
The M20 can also generate MTC (MIDI Time Code), used for MIDI sequencers and
computers; this is essentially the SMPTE message broken up into four parts and sent in
packets over a MIDI line. Unlike the analog SMPTE signal, MTC is not carried on a signal
that can provide a clock reference; it is sent on an interrupt basis between the other messages
of the MIDI signal such as note on/ off, aftertouch, pitch bend, etc.
For this reason, a digital audio system like the M20 cannot “slave to MTC” in a true
phase-lock manner. MTC is not stable enough a timing reference to derive a 48 kHz
digital clock from.
On the other hand, the normal use of MTC is to provide a location reference to machines that
don’t need that timing clock, such as computer sequencers and automated mixing consoles.
Even in these cases, standard analog SMPTE will often provide a more stable, jitter-free time
base than MTC. Consult the manuals for your other equipment for more information.
16-8
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAP T ER 17
TIM E CODE TUT ORIAL
17.1 GENERATING TIM E CODE ONTO A VCR
The first step in time code operations is to record time code onto a master and make sure the
slaves can read it. If you’re starting from scratch (i.e., no one is providing you with a video
tape already striped with time code), and you simply want to use the M20 as a time code
generator without simultaneously having it chase video, follow this procedure:
1
Press EDIT, then INT GEN. The display may read “1 GEN MODE:...”. If not, press INT
GEN again until it does.
2
3
Press the UP/YES key until the display reads “1 GEN MODE: Free Run”.
Press INT GEN again. The display will read “2 TC START REF:...” Press the UP/YES
or DOWN/NO keys until it says “User Set”.
Alternative: If you want to generate time code several times from the same starting
point, you may set the TC START REF to “Abs”. Unlike the User Set, this will keep
the same starting point if a tape is in the M20 and the transport’s stopped.
4
5
Press INT GEN again. The display reads “3 START: XX:XX:XX:XX” where X stands for
the last number generated in User Set mode. Using the keypad, enter the number you
want time code to start at. Optionally, you may press INT GEN again and enter the
User Bits following the procedure in section 11.7d. (Often, this is set to the month, day
and year the tape is being made.)
Connect the Time Code Out jack of the M20 to the input of the VCR (or analog audio
recorder) you want to record time code on. Usually, this is on audio track 2 of a VCR or
on the highest track of an analog multitrack.
If it’s a VCR, run a video output from the VCR to the Video Ref In of the M20. This
will be used as a clock source for the M20 so that the time code generated is “gen-
locked”, i.e., in sync with the actual video frames. If no other video units are connected,
turn on the 75 ohm termination switch below the jack. Set the M20’s Clock Source to
“VIDEO”.
Black burst generator: For the best results, use a video black generator connected to the
M20 and the VCR’s reference inputs instead of the VCR’s own video signal.
6
7
8
Press EDIT to leave edit mode. The blue light will turn off.
Set the desired SMPTE Rate and type (24, 25, 29.97, or 30 fps, drop or non-drop).
Press the REFERENCE COUNTER button until INT GEN is shown in the right
numeric display. Press INT GEN to turn its light on. Press the TC INPUT button so its
lamp is on.
At this point, the M20 is generating time code. You can see the right display counter count
the time, and the M20’s TC meter will light (“SIG”). Check the meter of the VCR for a good
level (usually from -5 to 0 dB). The VCR will normally have its own input level control. If
not, adjust the M20’s TC Output level using UTILITY (see section 13.7).
ALESIS M 20 REFERENCE M ANUAL 1.0 6
17-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Tim e Co d e Tu t o r ia l, Ch a p t e r 17
9
Press INT GEN or TC INPUT to stop the time code generator.
The variations of INT GEN should be easy to explore from this point on. Using different
options in steps 2, 3, and 4 above, you could generate time code that’s in lock-step with the
ABS time of the M20, that starts from the TC track reference, or only generates time code
when the M20 itself has a tape in it and is running.
17.2 SYNCHRONIZING W ITHOUT A T /C T RACK
Now that you have a master tape with time code, let’s get the M20 to chase and lock to the master
tape. The built-in ABS time code of the M20 may be used as a Chase Reference, without having to
pre-stripe a tape’s TC track. ABS Time is the sample-accurate time code written onto each ADAT
tape during the FORMAT process. It is used as the ultimate time reference for the system. This is
the time that shows in the 4-digit display of any ADAT ever built.
Using ABS as the Chase Reference is particularly useful in live recording when you don’t
have time to pre-stripe a tape. You can even synchronize while formatting, a unique
advantage of the ADAT format.
ADAT's internal time code is more accurate than conventional SMPTE time code. The M20 can
translate this ABS Time into any speed or type of SMPTE time code in order to synchronize with
non-ADAT masters or slaves. Since ABS Time covers only a 40 to 60-minute span, and SMPTE
covers a 24-hour day, the M20 was designed so it can translate any point of ADAT’s ABS Time to
any desired point on the 24-hour SMPTE/ EBU time code clock.
If you use the default settings of the M20, the zero point of every ADAT tape will translate to
"midnight" (00 hours, 00 minutes, 00 seconds, 00 frames) SMPTE. If you need to change this
"zero-to-zero" relationship between ADAT's ABS Time and incoming/ outgoing SMPTE time
code, you change either the INT GEN ABS offset or the SMPTE Chase offset.
Set SMPTE offset, frame-lock or lock & release, flywheel, park ahead
Chase = Abs time
Clock source: video (or word, or optical, etc.)
Make connections of SMPTE and clock source
Set Reference Counter to SMPTE IN, Tape Counter to ABS or SMPTE
17-2
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 17, Tim e Co d e Tu t o r ia l
17.3 RECORDING A TIM E CODE TRACK
The most stable and trouble-free method of synchronization for any SMPTE time code
system is to pre-stripe all tapes with generator-locked time code first, then perform any
transfers, recordings, and edits. If all time codes equal the same number, with no offsets,
and are the same SMPTE rate and type (drop or non-drop), and tapes are striped completely
from head to tail, this is the easiest and most foolproof system.
Make sure you record time code using the sample rate intended for the project! In a
digital audio recorder like the M20, there is a direct relationship betw een
the speed of time code and the sample rate. Time code recorded at 48 kHz
w ill play back slow if the w ord clock rate coming in is 44.1 kHz w hen the
tape is synchronized, making it impossible to lock properly.
17.3A RECORDING SM P TE FROM ABS TIM E
As explained in section 17.1, you can always generate SMPTE referenced to the ADAT’s
internal ABS time, even if there is no time code on the TC track. However, if you send that
tape out of your facility, they must set their INT GEN ABS Offset settings to the same as
yours before synchronizing. By recording the ABS Time with offset onto the TC track, they
merely have to set their Chase Reference to Tape TC, and the time code will be the same as
you used.
A benefit of having the TC track related directly to the ABS track is that all locate points will
be numerically related, causing a minimum of confusion. In addition, if the project requires
a different type or rate of time code for some reason later, it can easily be regenerated using
the INT GEN feature.
1
2
Press EDIT, then INT GEN until the display reads “1 GEN MODE: Play/Rec”.
Press INT GEN again. The display will read “2 TC START REF:...” Press the UP/YES
or DOWN/NO keys until it says “ABS Time”.
3
Press INT GEN again. The display reads “3 ABS: XX:XX:XX:XX” where X stands for the
last number entered in this page. Using the keypad, enter the number you want to
correspond to zero ABS time. Optionally, you may press INT GEN again and enter the
User Bits following the procedure in section 11.7d. (Often, this is set to the month, day
and year the tape is being made.)
Tip: In most typical video applications, programs start on the hour, with a two minute
preroll at the head of the tape. Set the ABS Offset to 00:58:00:00 in most cases. This
will make “1 o’clock” equal ABS time 00h 02m 00s 00f 00sf (two minutes from the
zero point). Often each reel of a program will have a different hour marker; the “two
minutes before the hour” convention usually still applies.
4
5
Leave EDIT mode, turn on INT GEN, and arm the TC track.
Set the M20’s Clock Source to “INT”. Set the Sample Rate to either 44.1K or 48K.
44.1K is used to conserve space on hard disk systems and if the project will be mixed
digitally to compact disc without sample rate conversion. 48K is the better choice if the
project will be mixed on an analog desk.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
17-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Tim e Co d e Tu t o r ia l, Ch a p t e r 17
6
7
Set the SMPTE Rate and type (24, 25, 29.97, or 30 fps, drop or non-drop).
Press the REFERENCE COUNTER button until TAPE TC is shown in the right
numeric display. This isn’t a required step, but it’s good practice.
8
Press PLAY and RECORD.
At this point, the M20 is recording time code of the specified type and number onto the TC
track, at the specified sample rate and speed.
Time code cannot be recorded on the LEAD and DATA sections of the tape. If the
tape is before ABS time 00h 00m 00s, no time code will be recorded, even though
the INT GEN will count properly through those sections.
SMPTE T/C coming from an analog deck or VCR is not recommended as a reference
clock for the M20, because it typically has too much w ow and flutter to be
multiplied into a stable 48 kHz sample clock. Use INT, VIDEO, or WORD clock
as a clock source whenever it’s available, using the SMPTE signal as a clock source
only if it’s extremely stable (from an external hardware generator or digital
source).
17-4
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 18 , M a in t e n a n ce a n d Tr o u b le s h o o t in g
CHAP T ER 18
M AINTENANCE AND
TROUBLESHOOT ING
Under no circumstances should you remove the top or bottom cover
of the M20 unless you are a qualified and careful technician. It is
possible to damage your heads and other sensitive parts of your
ADAT w henever the cover is open. Do not open up your ADAT to
clean the heads unless you are experienced in MDM or VCR
maintenance, have the approved tools and materials, and follow all
safety procedures.
18 .1 ADAT HEAD CLEANING
The most common cause of problems in playback or recording is dirty heads.
Depending on the quality of the tapes used and the environmental conditions where the
M20 and its tapes are stored, head cleaning will eventually become necessary. In
typical professional applications where many different tapes are used, a complete
head cleaning is recommended every 100 to 250 “drum on” hours, or whenever the
error rate (shown on Utility menu #20) begins to climb with a tape that is known to be
good (see section 4.11, “Recording a Benchmark Tape”).
To display the number of hours the head has been against the tape, hold PEAK
CLEAR and press STOP.
Note that due to the error correction process built into the M20, the actual sound quality
of an ADAT recording will not be affected unless there is quite a bit of dirt on the heads.
If the ERROR indicator (in between the two counters in the display) flashes on a
regular basis, even on newly-formatted tapes, we recommend that you bring your
M20 to an authorized Alesis Service Center for cleaning. If the indicator is not
appearing and the unit is performing normally, there is no reason to clean the heads.
Periodic or preventative maintenance on the M20 is NOT required as often as it is on
analog or video decks; in fact, overdoing it may cause premature wear.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
18-5
Download from Www.Somanuals.com. All Manuals Search And Download.
M a in t e n a n ce a n d Tr o u b le s h o o t in g , Ch a p t e r 18
18 .1A HEAD CLEANING CASSETTES (OP T IONAL)
For preventative maintenance, you may use a DRY VHS head cleaning cassette if you
wish, but Alesis does not see these as a substitute for thorough manual cleaning. Dry
cleaning tapes are simply VHS video tapes purposely made with a slightly coarse
surface. We recommend:
Sony Video Cleaning tape (model V-25CL)
TDK Video Head Cleaner (dry type only)
3M VHSHC Black Watch Head Cleaner Video Cassette
3M ASD HC Digital Audio Head Cleaning Cassette
Insert the tape into the M20 every 10-20 drum hours, play the tape through once,
(normally 2-3 minutes) rewind it, then eject it. Most of these tapes are encoded with a
video signal; you may erase that by formatting the cleaning tape. If you play the tape
without formatting it, it will still do the job, but various error messages may appear
during the process.
Dry head cleaning tapes become less effective each time they are used; many brands
recommend a new tape after 20 passes through the machine. While they are mildly
abrasive, they do not wear the heads significantly when used properly.
On the down side, head cleaning cassettes are seldom effective on a head that is already
dirty enough to cause significant errors. In an emergency, you may use a cleaning tape
several times in a row to get the heads clean enough to get through a session, but a
complete cleaning by a qualified service technician will still be needed.
·
Do NOT use any other type of head cleaning cassette. They are abrasive and will
damage or wear out your heads.
·
·
Do NOT use head cleaning cassettes that require any kind of liquid.
Do NOT attempt to clean the heads yourself unless you are a skilled technician
experienced in the maintenance of video cassette recorders. Information for such
technicians is available below and from Alesis Product Support. ADAT head
cleaning requires different materials and procedures from analog head cleaning,
similar to VCR maintenance. Cleaning the heads with a cotton swab, or rubbing
in the wrong direction, will destroy them. Opening the case of your ADAT will
void the warranty.
18 .1B M ANUAL HEAD AND TAP E P AT H CLEANING
If the error count is high, or more than 250 “drum on” hours have elapsed since the last
complete cleaning, a manual cleaning of the head drum and tape path is recommended.
If you are experienced in VCR maintenance, you may clean the heads of the M20
yourself. Otherwise, this service may be performed by an Alesis service center for a
nominal charge.
Eject the tape, turn the POWER sw itch off, and unplug the M20 from
AC pow er before opening the unit!
18-6
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 18 , M a in t e n a n ce a n d Tr o u b le s h o o t in g
We do not recommend cleaning the heads with cotton or foam swabs, or chamois.
The safest and most effective cleaning is performed using a hydroentangled polyester
wipe (Techclean® Wiper #2350, available from Tech Spray) soaked in pure 99%
anhydrous (water free) isopropyl alcohol. This particular wipe is lint and particle-free,
designed for use in laboratory clean rooms. Note: other Techclean wipes are NOT
necessarily lint free; make sure you obtain this type or equivalent. If the head is severely
soiled or has been exposed to tobacco smoke or silicone-contaminated tape, you may
use a plastic-safe non-toxic VCR tape head cleaning solution such as Techclean
Professional Head Cleaner #1673 instead of isopropyl alcohol.
Hold the wipe against the head drum with your finger and rotate the drum counter-
clockwise. You should feel the head tips against your fingertip.
Do not move your finger on the drum; only rotate the drum. Moving
your hand may throw the heads out of alignment, requiring factory
service!
Clean all other objects in the tape path using the same materials, as instructed, paying
special attention to the linear head, and lower drum guide. Call Alesis Product
Support for more detailed information about head cleaning . Instructional videotapes
are available for a small charge.
18 .2 ADAT HEAD LIFE
The expected head life for each ADAT varies according to a number of factors. Given
optimum conditions, tape quality, tape care, and operating environment, head life for
the average ADAT will always be better than if your ADAT is abused, placed in bad
environmental conditions and used with badly maintained tapes. Properly cared for,
your heads should last for thousands of hours; in fact, Alesis warrants the heads for a
period of 1,500 drum hours or one year, whichever comes first.
You should not subject your M20 to environmental extremes, humidity or moisture of
any kind, dust, dirt, extreme temperatures, extreme temperature fluctuations or any
kind of physical abuse (drops, shocks). Even though it has been built for heavy
professional use, ADAT is a very sophisticated piece of digital technology. It is going
to be used for your important projects so take the best care of your ADAT and your
ADAT heads possible.
Head replacement is not indicated unless a service technician cannot get an acceptable
signal from the head drum during a test procedure.
18 .2A HEAD ALIGNM ENT
The heads of each ADAT are pre-aligned at Alesis. No user adjustment is necessary.
Take care not to hit the rotary head drum or the linear head with any metal tools during
service.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
18-7
Download from Www.Somanuals.com. All Manuals Search And Download.
M a in t e n a n ce a n d Tr o u b le s h o o t in g , Ch a p t e r 18
18 .3 TAP E M AINTENANCE: SAFE TAP E
18 .3A TAP E W EAR
Head maintenance of the ADAT should be based on the ERROR Indicator (or Error
Count Display) or if the unit begins to behave erratically. However, these same
symptoms may appear in an M20 with clean heads if the tape being used is worn out or
defective.
To determine if a high error rate is being caused by dirty heads or by a defective or
worn tape, keep a “benchmark” tape from the first weeks of operation set aside in a safe
place (see section 4.11). If the ERROR Indicator lights frequently when playing back
this tape, it is likely that head cleaning is needed, particularly if several hundred drum-
on hours have elapsed since the last cleaning.
But if errors appear only with certain tapes, that tape is experiencing dropouts or
other wear. Make a digital backup immediately onto a new tape and use the backup
for future work.
18 .3B CARE OF ADAT TAP ES
ADAT tapes are no different than any standard tape: they must be treated with care.
Never expose ADAT tapes to temperature extremes, strong magnetic fields (such as
speakers), high humidity, dust and so on. High humidity is a particular problem with
magnetic media, as it causes the binders to soften, increasing wear and depositing tape
oxide on the heads.
You should always practice “SAFE TAPE”:
·
At the end of every session you should rewind the tape all the way to the leader,
stop, eject the tape, remove it from the ADAT and place it in its protective case.
This cuts down on the amount of dust that can enter the transport and keeps wear
on the tape at a minimum.
·
Don’t leave your tapes near speakers, power amps or other potential magnetic fields
such as televisions or electrical devices.
·
·
·
Don’t subject your tapes to extreme temperatures or wild temperature fluctuations.
Don’t expose your tapes to high humidity, moisture or high dust levels.
Don’t leave your tapes on the dashboard of your car. (In fact, never leave ADAT
tapes in a car EVER. Keep them with you at all times!)
·
Certainly, no matter how tempted you are to open the shutter to see what is inside,
NEVER TOUCH THE TAPE. The magnetic particles on your ADAT tape need to be
preserved in the condition in which they were recorded. The oils from your fingers
may damage your tapes as well as get on the heads and get them dirty.
·
Never turn off the ADAT power while the tape is threaded. This leaves the tape
bent around the rollers and head. Eject the tape or press STOP until the tape is
unthreaded (STOP button blinking) before turning off power.
18-8
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r 18 , M a in t e n a n ce a n d Tr o u b le s h o o t in g
Practice “safe tape” at all times because you can never retrieve lost data.
If you are archiving your tapes, make sure they are stored in environmentally stable
conditions, i.e. a cool dry place. If you do archive your tapes, you need to check them
once a year. Run each tape through your ADAT from end to end. This will prevent
buildup that can occur when a tape is left simply “sitting”.
Of course, for your super sensitive or important material, nothing beats making multiple
digital backups. Every year or so, simply do another digital backup onto a brand new
tape.
18 .4 M AINTENANCE/SERVICE
18 .4 A EXT ERIOR CLEANING
Disconnect the AC cord, then use a damp cloth to clean the front panel’s metal and
plastic surfaces. For heavy dirt, use a non-abrasive household cleaner such as Formula
409 or Fantastik.
DO NOT SPRAY THE CLEANER DIRECTLY ONTO THE FRONT OF THE
UNIT AS IT MAY DESTROY THE LUBRICANTS USED IN THE SWITCHES
AND CONTROLS! Spray onto a cloth, then use the cloth to clean the
unit.
18 .4 B M AINT ENANCE
Here are some tips for preventive maintenance.
•
•
•
Periodically check the AC cord for signs of fraying or damage.
Unplug the M20 when not in use for extended periods of time.
Do not leave tapes inserted halfway into the M20 when not in use, as this allows
dust to enter the transport chamber. Always leave tapes either fully inserted, or
remove them completely.
18 .4 C REFER ALL SERVICING T O ALESIS
We believe that the M20 is one of the most reliable digital recorders that can be made
using current technology, and should provide years of trouble-free use. However,
should problems occur, DO NOT attempt to service the unit yourself. The full AC line
voltage, as well as high voltage/ high current DC voltages, are present at several points
within the chassis. Service on this product should be performed only by qualified
technicians. THERE ARE NO USER-SERVICEABLE PARTS INSIDE.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
18-9
Download from Www.Somanuals.com. All Manuals Search And Download.
M a in t e n a n ce a n d Tr o u b le s h o o t in g , Ch a p t e r 18
18 .4 D OBT AINING REP AIR SERVICE
Before contacting Alesis, check over all your connections, and make sure you’ve read
the manual.
Customers in the USA:
If the problem persists, call Alesis USA at 1-800-5ALESIS and request the Product
Support department. Please have your serial number (located on the back of the
machine and starting with a “3D”) when you call. Talk the problem over with one of our
technicians; if necessary, you will be given a repair order (RO) number and instructions
on how to return the unit. All units must be shipped prepaid and COD shipments will
not be accepted.
For prompt service, indicate the RO number on the shipping label. If you do not have
the original packing, ship the M20 in a sturdy carton, with shock-absorbing materials
such as styrofoam pellets (the kind without CFCs, please) or “bubble-pack” surrounding
the unit. Shipping damage caused by inadequate packing is not covered by the Alesis
warranty.
Tape a note to the top of the unit describing the problem, include your name and a
phone number where Alesis can contact you if necessary, as well as instructions on
where you want the product returned. Alesis will pay for standard one-way shipping
back to you on any repair covered under the terms of this warranty. Next day service is
available for a surcharge.
Field repairs are not normally authorized during the warranty period, and repair
attempts by unqualified personnel may invalidate the warranty.
Correspondence address for customers in the USA:
Alesis Product Support
1633 26th Street
Santa Monica, CA 90404
This is not a service location. Do not ship units to the above address.
Customers outside the USA:
Contact your local Alesis dealer for warranty assistance. The Alesis Limited Warranty
applies only to products sold to users in the USA and Canada. Customers outside the
USA and Canada are not covered by this Limited Warranty and may or may not be
covered by independent distributor warranty in the county of sale. Do not return
products to the factory unless you have been given specific instructions to do so.
18-10
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
AP P ENDIX 1
M 20 HIDDEN FUNCT IONS
P OW ER-ON BUTTON COM BINATIONS
Holding the following button combinations when the M20 is powered-on will allow
access to the following special functions:
·
Play and Record
Performs a user reset which initializes all parameters to their default values. The
display will show “Initializing …”
M ISCELLANEOUS BUTTON COM BINATIONS
Accessing hidden functions involves holding the Peak Clear button in combination with
the following buttons:
·
·
Stop
Displays drum head hours.
Eject
When pressed on the master unit, only the master tape is ejected, i.e. the eject
command is not sent to the slaves.
·
Record
This allows the user to record on a write-protected tape. It toggles between
“OVERRIDE WRITE PROTECT” which allows recording regardless of the write-
protect tab status, and “SENSE WRITE PROTECT” which only allows recording if
the write-protect tab is intact. Note that this function can only be toggled if a tape is
loaded. The override is reset to sense the write-protect tab whenever a tape is
ejected.
·
Auto Return
Displays the number of continuous auto-loops.
Accessing other hidden functions involves holding the Peak Mode button in
combination with the following buttons:
·
·
Stop
The transport enters deck standby mode. In this mode, the cassette remains loaded
in the transport and the tape is completely withdrawn into the cassette.
Eject
This performs an auto-inject. When a cassette is partially inserted (as is the case
when a cassette remains in the transport door after an eject command), the cassette
will automatically load into the transport.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
A1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Ap p e n d ix 1, M 20 Hid d e n Fu n ct io n s
A1-2
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
M 20 So ft w a r e Ve r s io n 2.0 0
ADVANCED FUNCTIONS
Although not technically hidden functions, the following are additional advanced
features that are not obvious:
·
·
Holding Stop for at least 3 seconds will force the tape to unthread.
Double-clicking the Fast Forward or Rewind button (pressing the button twice
within 500 milliseconds) will cause the tape to wind at the fastest possible speed
(approximately 85X play speed) with the capstan disengaged.
·
·
Holding the Search button for at least 3 seconds will allow editing of the Search
Master (see M20 manual section 8.4d).
While in a locate name field, pressing the Up or Down button while holding Name
will scroll through a list of 16 default names. To customize a name in this list, edit
the name, then hold Name and press Record. The list of user-defined names will be
retained through a power-cycle and will resort back to the default names with a
user reset.
·
·
Holding Sample Rate and pressing Up, Down, or 0 will allow Pull Up, Pull Down or
No Pull Up/ Down, respectively.
Holding Edit while pressing Rollback will allow editing of the Rollback time. Refer
to the CADI user manual for further details.
M 20 ADDENDUM 2.0
MA-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
AP P ENDIX 2
USING THE M 20 DATA
SECT ION OF TAP E
GENERAL DATA SECTION CONVENTION ON THE M 20
The M20 saves setup data to an ADAT tape’s data section using the Alesis BRC Table of
Contents (TOC) as a template. In other words, the M20 will only save and recall a TOC
for those locate points and parameters that have a BRC equivalent. To save and recall
the entire M20 locate point and parameter set, perform a system exclusive MIDI dump
(see M20 manual sections 12.4 and 12.5).
M 20 LOCATE P OINTS AND SM P TE OFFSET S
The M20 has 100 locate points and 1 SMPTE offset value. With a CADI, the M20 can
recall 10 Setups. Each Setup has a dedicated SMPTE offset value, bringing the total
number of available SMPTE offsets to 10. The M20’s locate points are independent of
the Setups, so the same 100 locate points are available to each Setup.
BRC Û M 20 SONG START / SM P TE START OFFSET
AND LOCATE P OINT M AP
BRC
M20
Song Start 01
Ê
Û
SMPTE Offset Value or CADI Setup 01 SMPTE Offset Value
Song 01/ Loc 00
Song 01/ Loc 01
Song 01/ Loc 02
.
Û
Û
Û
(Not Saved) Ë
Loc 01
Loc 02
.
.
Song 01/ Loc 20
Song 01/ Loc 21
Song 01/ Loc 22
Û
Û
Û
Loc 20
Loc 98 Ì
Loc 99 Ì
Song Start 02
Song 02/ Loc 01
Song 02/ Loc 02
Song 02/ Loc 03
Û
Û
Û
Û
(Not Recalled) Í
Loc 21
Loc 22
Loc 23
.
.
.
Song 02/ Loc 20
Song 02/ Loc 21
Song 02/ Loc 22
Û
Û
Û
Loc 40
(Not Recalled)
(Not Recalled)
.
.
ALESIS M 20 REFERENCE M ANUAL 1.0 6
A2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Ap p e n d ix 2, Us in g Th e M 20 Da t a Se ct io n Of Ta p e
.
Song 05/ Loc 01
Song 05/ Loc 02
Song 05/ Loc 03
.
Û
Û
Û
Loc 81
Loc 82
Loc 83
.
.
Song 05/ Loc 17
Song 05/ Loc 18
Song 05/ Loc 19
Song 05/ Loc 20
Song 05/ Loc 21
Song 05/ Loc 22
Û
Û
Û
Û
Û
Û
Loc 97
(Not Recalled)
(Not Recalled)
(Not Recalled)
(Not Recalled)
(Not Recalled)
Song 06
.
Locates Û
(Not Recalled)
.
.
Song 20
Locates Û
(Not Recalled) Î
Ê Only the Song 01 Start Offset is recalled by the M20.
Ë The BRC does not save Locate 00 to the data section of tape.
Ì Only the Song 01 Punch-In/ Out Points are recalled by the M20.
Í The M20 does not recall this value from the data section of tape.
Î The M20 does not recall the Song Start or Locate addresses for Song 6 through Song
20.
BRC Û M 20 P ARAM ETER M AP
BRC
M20
All Safe
All Input Enable
Display Type
Ext Sync/ Clock Source
SMPTE
Enable
Û
Û
Û
Û
Û
Û
Û
Û
Û
Û
Û
Û
Û
Û
Û
Û
Û
Û
Û
Û
Û
Û
All Safe Enable
All Input Enable
Tape Counter Mode
Clock Source
SMPTE Rate
Pitch Mode
Pitch Mode
Ext Sync/ Locate Reference-SMPTE Input
SMPTE Start Offset
Ext Sync/ Ext Sync Mode
Gen Sync/ SMPTE On
Tape Offset Enable
Tape Offset/ Offset Mode
Offset Tape 01 Value
Offset Tape 01 “From” Point
Offset Tape 01 “To” Point
Track Delay Enable
Delay Value for ID 1
Pre-Roll Enable
SMPTE Chase Enable
SMPTE Chase/ SMPTE Offset Value
SMPTE Chase/ Chase Mode
Internal Generator Enable
Tape Offset Enable
Tape Offset/ Offset Mode
Offset Value
Offset Loc Pt 1
Offset Loc Pt 2
Track Delay Enable
Delay Value
Pre-Roll Enable
Pre-Roll/ Pre-Roll Time
Post-Roll Enable
Post-Roll/ Post-Roll Time
Auto-Punch Enable
Pre-Roll/ Pre-Roll Time
Post-Roll Enable
Post-Roll/ Post-Roll Time
Auto Record Enable
A2-2
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ap p e n d ix 2, Us in g Th e M 20 Da t a Se ct io n Of
Ta p e
Auto-Punch/ In
Auto-Punch/ Ot
Loop Enable
Loop/ St
Û
Û
Û
Û
Û
Û
Û
Û
Û
Û
Û
Auto Record/ In Pt
Auto Record/ Out Pt
Auto Return Enable
Auto Return/ Strt Pt
Auto Return/ End Pt
Auto Input Enable
Auto Play Enable
Loop/ En
Auto Input Enable
Auto Play Enable
Pitch Control Value
MIDI/ Util/ MIDI Device Value
Record Xfade/ Crossfade Time
Rehearse Enable
Vari-Speed Value
Utility/ MIDI Device Value
Utility/ Xfade Time
Rehearse Enable
ALESIS M 20 REFERENCE M ANUAL 1.0 6
A2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Ap p e n d ix 2, Us in g Th e M 20 Da t a Se ct io n Of Ta p e
A2-4
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
AP P ENDIX 3
M 20 TRANSP ORT &
SYST EM ERROR M ESSAGES
PLAY STATE ERRORS:
"QuarterToPlay ERROR"
If current speed is assumed to be 1/ 4x
when actually not
"Track Skip timeout error"
"ERROR: StopPoint default"
"CAP SERVO CNTR TIMEOUT 1"
Track skipping not completed within 6
seconds
Default case when calculating play stop
point
Capstan FG error feedback from servo chip
is not within range after 2 seconds when
transitioning from stop to play
BRAKING STATE ERRORS:
"BRAKING TIMEOUT ERROR 1"
"BRAKING TIMEOUT ERROR 2"
"Default case StopTape"
If capstan direction bit does not flip within
2 seconds of braking
If a capstan disengaged stop exceeds 3
seconds
Error with value passed to stop tape
LOCATE STATE ERRORS:
"ERR: SLAVE CAN'T LOCATE"
If master cannot confirm a slave has
successfully located before a play if locate
before play is enabled OR after a locate if
auto play is enabled or a play is pending
If master cannot confirm a slave has
successfully located after a replay if auto
play is enabled or a play is pending
If master cannot confirm a slave has
successfully located after a rollback if auto
play is enabled or a play is pending
Invalid result from capstan engaged wind
when locating
"ERR: SLAVE CAN'T REPLAY"
"SLAVE CAN'T ROLLBACK"
"INVALID LOCATE CONDITION"
ALESIS M 20 REFERENCE M ANUAL 1.0 6
A3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Ap p e n d ix 3, M 20 Tr a n s p o r t & Sys t e m Er r o r M e s s a g e s
WIND STATE ERRORS:
"FORWARD TIMEOUT ERROR 1"
"REWIND TIMEOUT ERROR 1"
Slowdown time from capstan disengaged
fast wind to capstan engaged wind exceeds
3 sec
Slowdown time from capstan disengaged
fast wind to capstan engaged wind exceeds
3 sec
"INVALID FWD CONDITION 1"
"INVALID REW CONDITION 1"
"INVALID FWD CONDITION 2"
"INVALID REW CONDITION 2"
"INVALID FWD CONDITION 3"
"INVALID REW CONDITION 3"
“TC wait state invalid”
Invalid result of capstan engaged slower
wind
Invalid result of capstan engaged slower
wind
If a destination is reached during a capstan
engaged wind
If a destination is reached during a capstan
engaged wind
If a destination is reached during a capstan
disengaged wind
If a destination is reached during a capstan
disengaged wind
Tape is fast-forwarding or rewinding and
the local time code is the same for 200
consecutive queries, which is about a 3-
second timeout
TAPE TYPE DETECTION ERRORS:
"CALIBRATION ERROR 1"
"CALIBRATION ERROR 2"
"CALIBRATION ERROR 3"
Tape type determined when not at play
speed
Problem in getting tape to necessary speed
to allow calibration
Problem in getting tape to necessary speed
to allow calibration
"CALIBRATION ERROR 4"
"CALIBRATION ERROR 5"
"CALIBRATION ERROR 6"
"CALIBRATION ERROR 7"
"CALIBRATION ERROR 8"
"CALIBRATION ERROR 9”
Problem when calibrating takeup reel
Supply tach can’t use timer resource
Trying to calibrate an unformatted tape
Beginning of tape sensor error
No supply tachs present for calibration
Capstan speed feedback from servo chip is
not in range
"CALIBRATION ERROR 10"
"CALIBRATION ERROR 11"
Clock source changed during calibration
Local time code value out of range for large
hub tape
"CALIBRATION ERROR 12"
"CALIBRATION ERROR 13"
Local time code value out of range for small
hub tape
Error in result of hub size calculation
A3-2
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ap p e n d ix 3, M 20 Tr a n s p o r t & Sys t e m Er r o r
M e s s a g e s
CAPSTAN STATE TRANSITION ERRORS:
"CAPSTAN CONSTANTS ERROR"
"CAP PWM TO SERVO SWITCH"
"NO CAPSTAN FGs ERROR 1"
"NO CAPSTAN FGs ERROR 3"
"NO CAPSTAN FGs IN JOG"
"NOISY CAPSTAN FG"
Default case when loading capstan
constants
When capstan is not off when switching to
servo control
No capstan tach pulses are detected when
changing capstan speeds
No capstan tach pulses are detected when
changing capstan speeds
No capstan tach pulses are detected when
in jog
Capstan tach pulse period is outside
acceptable range
"CAP CAN'T GET TO SPEED 1"
"CAP CAN'T GET TO SPEED 2"
"CAP SERVO COUNTR TIMEOUT"
Capstan can’t get to target speed within 5
seconds when slowing down
Capstan can’t get to target speed within 5
seconds when speeding up
Capstan FG error feedback from servo chip
is not within range after 5 seconds
immediately following a speed change
If capstan not off and current direction is
not the same as the desired direction
If capstan target speed is not a servo-
defined speed
"RAMP CAP ILLEGAL CASE 1"
"RAMP CAP ILLEGAL CASE 2"
"RAMP CAP ILLEGAL CASE 3"
"RAMP CAP ILLEGAL CASE 4"
When capstan is not off when switching to
servo control
If capstan target speed is illegal (format)
DRUM STATE TRANSITION ERRORS:
"ERROR: NO DRUM FGs"
No drum tach pulses are detected when
drum is turned on
"DRUM STARTUP ERROR 0"
"DRUM STARTUP ERROR 1"
"DRUM STARTUP ERROR 2"
"DRUM STARTUP ERROR 3"
"DRUM STARTUP ERROR 4"
Drum is already turned full on when servo
lock is attempted
Drum jitters for more than 5 seconds when
starting up
Drum not at target speed (measured with
µP) within 5 seconds
Drum not at target speed (measured with
servo chip) within 5 seconds
Drum speed feedback from servo chip is
not stable within 2 seconds
ALESIS M 20 REFERENCE M ANUAL 1.0 6
A3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Ap p e n d ix 3, M 20 Tr a n s p o r t & Sys t e m Er r o r M e s s a g e s
DECK STATE TRANSITION ERRORS:
"DECK INIT ERROR"
Error in deck mode switch when initializing
deck mode
"DECK MODE ERROR"
Error in deck mode switch during deck
monitoring
"DECK MODE TIMEOUT ERROR"
"UnthreadSem TIMEOUT ERROR"
"ERROR: EjectSem1 Timeout"
"ERROR: EjectSem2 Timeout"
Deck does not reach destination mode
within 2 seconds
During load, deck didn’t reach unthreaded
within 2 seconds
Problem with cassette present sensor, load
switch, or load motor
Problem with cassette present sensor, load
switch, or load motor
"ERROR: EjectSem3 Timeout"
"END OF TAPE SENSOR ERROR"
Problem with load switch or load motor
After threading tape, end of tape sensor still
active after rewinding
"ERROR: DEW SENSOR ACTIVE"
"ERROR: TAPE DOWN TIMEOUT"
Dew sensor is active when loading
During load, load switch didn’t get to
proper state within 2 seconds
BACKGROUND ERROR MONITORING:
"END SENSOR ERROR"
When the sensors are in an illogical state,
the tape will be ejected
"DEW SENSOR TRIGGERED"
"SUPPLY REEL ERROR"
When the dew sensor is activated, the tape
will be ejected
When no supply motor tachs are detected,
the tape will be ejected
"TAKEUP REEL ERROR"
"CAPSTAN ERROR"
When no takeup motor tachs are detected,
the tape will be ejected
When no capstan motor tachs are detected,
the tape will be ejected
"DRUM SPEED ERROR"
When the drum period is out of range, the
tape will unthread and the drum will
attempt to reservo
“Crossfade error!!”
The crossfade error checking routine makes
sure that each tape is correctly crossfaded.
Displays this error message if in the
crossfade error checking routine, a tape
state crossfade is wrong.
A3-4
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ap p e n d ix 3, M 20 Tr a n s p o r t & Sys t e m Er r o r
M e s s a g e s
OTHER ERRORS MESSAGES:
"SUPPLY CAN'T USE TIMER 2"
"TAKEUP CAN'T USE TIMER 2"
"LT CAN'T USE TIMER 2"
Takes longer than 3 seconds for supply tach
to use timer resource
Takes longer than 3 seconds for takeup tach
to use timer resource
Takes longer than 3 seconds for linear track
to use timer resource
"CAPSTAN CAN'T USE TIMER 2"
"DRUM CAN'T USE TIMER 2"
Takes longer than 3 seconds for capstan
tach to use timer resource
Takes longer than 3 seconds for drum tach
to use timer resource
"GET TIMER 2 NOW ERROR"
"Search Master is Offline"
"Err: Search Master Poll"
Error with value passed to grab timer
If search master is offline
If master (ID1) gets no response from search
master within 2 seconds
"ERROR - Dew detected"
"ERROR - Write Protected"
"Beyond Auto-Punch Region"
When the dew sensor is active when a
record enter is performed
When a record to a write protected tape is
attempted
If a record strobe is performed beyond auto
punch out point when auto record is
enabled
WARNING MESSAGES:
"Tape Offset Standby"
If slave with offset wants to chase to
negative time code
"WARNING - Non SVHS Tape"
"SVHS TAPES RECOMMENDED"
"TAPE WRITE PROTECTED"
When a non-SVHS tape is punched in on
When a non-SVHS tape is inserted
Tape can’t be recorded on is inserted (i.e.
write protect tap is removed)
When a locate destination is beyond the end
of tape
When a locate destination is beyond the end
of tape
When ADAT clock is present but outside
acceptable frequency range
When word clock is present but outside
acceptable frequency range
When audio clock is present but outside
acceptable frequency range
When SMPTE clock is present but outside
acceptable frequency range
When video clock is present but outside
acceptable frequency range
"LOCATE OUT OF RANGE"
"LOCATION OUT OF RANGE"
"ADAT clock out of range"
"Word clock out of range"
"Audio clock out of range"
"SMPTE clock out of range"
"Video clock out of range"
"Calibrating ... Standby"
"Timecode invalid"
Software is determining what type of tape
was inserted
Tape is formatted but time code cannot be
read
ALESIS M 20 REFERENCE M ANUAL 1.0 6
A3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Ap p e n d ix 3, M 20 Tr a n s p o r t & Sys t e m Er r o r M e s s a g e s
A3-6
ALESIS M 20 REFERENCE M ANUAL 1.0 6
Download from Www.Somanuals.com. All Manuals Search And Download.
M 20 M AJOR FEAT URE
UP DAT E: VERSION 2
Version 2.00 Features
RS-4 22 (SONY 9 -P IN) SLAVE OP ERATION
The Online Source page in the Utility menu now has the “RS-422” parameter added to
its choice of online control source settings. Two new utility pages have also been added
to facilitate RS-422 slave track arming operations. When Online Source is set to RS-422,
the M20 will recognize standard Sony 9-pin control commands. The M20 is optimized
for BVU-950 emulation.
The way RS-422 Edit Preset commands record arm M20 tracks is determined by the RS-
422 Track Arm and RS-422 Mapping settings. These Utility pages are defined as
follows:
RS-4 22 TRACK ARM : ON/OFF
When on, the M20 will respond to RS-422 Edit Preset commands by record arming M20
tracks according to the mapping page setting. When off, local track arming from the
M20 front panel is allowed i.e., Edit Preset commands are ignored. Local track arming is
recommended when slave M20s (ID 2 and above) must be record enabled, or when ID 1
record arming that does not follow the assigned RS-422 mapping scheme is desirable.
RS-4 22 M AP P ING: 1-2, ODDEVN, (LOCAL)
This parameter sets the mapping for 2-track (BVU-950) Edit Preset commands. When
set to 1-2, an A1 or A2 track arm command will record arm M20 tracks 1 and 2
respectively. No mapping to other M20 tracks will occur. When OddEvn (Odd/ Even) is
selected, an A1 track arm command will record arm tracks 1, 3, 5, and 7 (the odd
channels) and an A2 track arm command will record arm tracks 2, 4, 6, and 8 (the even
channels). If an RS-422 controller can force an emulation type other than SONY BVU-
950 (e.g. Sony DVR-10 or Fostex RD-8) for the purposes of using A1-A4 (4 track Edit
Preset) or Da1-Da8 (8 track Edit Preset) arming with the M20, the map setting will be
ignored. This, for example, will allow an A1 or A2 track arm command from a DVR-10
(a VTR with 4 audio tracks) to record arm track 1 or track 2 of the M20 without
mapping, i.e. M20 tracks 3 and 4 can be record armed independently with an A3 or A4
Edit Preset command regardless of the map setting.
If RS-422 Track Arm is off, “(Local)” is indicated in place of the mapping selection and
editing is not allowed. When Track map is turned back on, the previously selected RS-
422 mapping selection is reverted to and editing is allowed.
M 20 ADDENDUM 2.1
MA-1
Download from Www.Somanuals.com. All Manuals Search And Download.
M 20 So ft w a r e Ve r s io n 2
ID 1 OFFLINE W ITH THE CADI REM OTE
When the CADI remote is connected to multiple M20 recorders, the ID 1 master can now be
taken offline. ID 1 maintains clock and serial control over all slaves (excluding 32-bit ABS
time code). Using a CADI, when ID 1 is offline, its transport remains idle while the CADI
transport controls operate the next online slave (known as the pseudo-master). Without a
CADI connected, an offline ID 1 M20 transport will continue to operate normally and
control online slaves.
CADI TAP E AND REFERENCE COUNTER INDICATIONS
W HEN ID 1 IS OFFLINE
The CADI’s display shows the pseudo-master’s ABS and Tape TC values on the Tape and
Reference Counters respectively. The CADI’s Reference Counter will not show the pseudo-
master’s SMPTE In, Locate Point, Internal Generator, or SMPTE Offset values.
STORING LOCATE P OINTS W HEN ID 1 IS OFFLINE
When updating locate points (e.g. pressing Set Locate on the CADI), ID 1 locate points are
overwritten based on the pseudo-master’s tape position. For example, pressing Copy Tape
Location on the CADI will write ID 2’s tape position into ID 1’s currently selected locate
address. The following scenarios suggest operation when ID 1 is offline:
M20 master and two slaves (ID 1 à ID 2 à ID 3)
ID 1 Offline
·
With ID 1 offline, the system will function normally. Transport operations performed
on ID 1 will control online slaves (32-bit ABS time code is transmitted). The only
difference is that ID 1 will ignore any remote online source input.
CADI with M20 master and two slaves (CADI à ID 1 à ID 2 à ID 3)
ID 1 Offline
·
·
·
The first online unit becomes the pseudo-master. The pseudo-master will operate like a
master in regards to all transport functions, including Rollback, Replay, Loc Before
Play, Mute Until Lock, etc.
The CADI will reflect ID 1 parameters with the following exceptions: Tape Counter,
Reference Counter – Tape TC only, and transport status. The CADI will reflect the
pseudo-master status in these cases.
All track enable selections and track groups along with All Input, All Safe, and All
Clear functions initiated from the CADI will be ignored by ID 1. The “Machine
Offline” message is temporarily displayed when a track selection is attempted (similar
to what occurs when trying to record or input enable an offline ID 2 or greater unit).
·
There is no independent use of the ID 1 front panel functions other than Eject and
Online functions.
M 20 ADDENDUM 2.1
MA-2
Download from Www.Somanuals.com. All Manuals Search And Download.
M 20 So ft w a r e Ve r s io n 2
·
Using Tape Offset mode.
1. Tape Offset is enabled, ID 2’s tape offset value is non-zero and user tries to take ID
1 offline:
ID 1 offline is not allowed and “ID 2 Tape Offset Not Zero” is temporarily displayed.
2. ID 1 is offline, ID 2’s tape offset value is non-zero and the user tries to enable Tape
Offset:
Tape Offset enable is not allowed and “ID 2 Tape Offset Not Zero” is temporarily
displayed.
·
When ID 1 is put back online, all slaves will stop. CADI and slave memory is updated
to be consistent with ID 1 parameters.
All Machines Offline
·
If no machines are online, then the CADI will display “No Machines Online” when any
action is attempted.
Special notes when operating a CADI with ID 1 offline
No SMPTE Chase
·
SMPTE Chase remains a function of the ID 1 machine. ID 1’s SMPTE Chase parameter
settings are reflected on the CADI display even when ID 1 is offline. When ID 1 is
offline, SMPTE Chase for the pseudo-master and remaining slaves is not permitted.
Internal Generator operation
·
ID 1’s internal generator parameter settings are reflected on the CADI display even
when ID 1 is offline. The pseudo-master’s internal generator will operate, but its
output is subject to its own internal generator parameter settings (which may differ
from the ID 1 settings). Therefore, in most situations, time code generation should
remain a function of the ID 1 machine.
TAP E T C DETECTION IN FAST W IND M ODES
Detecting discontinuous and noncontiguous Tape TC in fast wind modes has been
implemented. The M20 will recognize TC Track time code discontinuities and time code
gaps in fast wind modes, i.e., when chasing time code or during a locate, scan, search, fast
forward, or rewind). In addition, when Rew/ Fwd TC Out is on, time code accurate with
the TC Track will be present at the M20’s Time Code and MIDI Outputs in fast wind
modes.
Please note that for speeds less than 1X (one times) play speed, the Tape TC is extrapolated
from the last valid reading.
M 20 ADDENDUM 2.1
MA-3
Download from Www.Somanuals.com. All Manuals Search And Download.
M 20 So ft w a r e Ve r s io n 2
Note the following exceptions when using tapes previously formatted with v1.xx software:
·
·
When a version 1.xx formatted tape has tc recorded to it using version 1.xx software,
time code discontinuities and non-contiguities in fast wind will not be recognized. In
this case, the M20 will extrapolate time code values when in wind modes (based on the
last valid tape tc detected in Play or Record mode).
When a version 1.xx formatted tape has tape tc recorded to it using version 2.xx
software, time code discontinuities will be detected in wind modes. However, time
code values will be extrapolated when a section of tape without time code
(noncontiguous time code) is encountered while winding. Once Play or Record is
pressed, the actual tape tc value (if present and different) will be detected and properly
displayed.
TAP E T C IN THE TAP E COUNTER
When the Tape Counter selection is SMPTE, the display is now based upon the chase
reference selection:
·
·
When the chase reference is ABS Time, the display shows the ABS Time plus SMPTE
Offset value, as before.
When the chase reference is TapeTC, the display now shows the Tape TC plus SMPTE
Offset value.
When Tape TC is selected as a chase reference and no Tape TC is detected on tape, the
Tape Counter will indicate “no tAPE tc” when in SMPTE mode.
FIXED M ODE TIM E CODE GENERATION: “T C START REF:
FIXED”
The internal generator’s TC start reference parameter can now be set to “Fixed”. When in
Fixed mode, the start offset does not update to the last generated value when time code
generation stops as is the case with User Set mode. Fixed mode will maintain the same start
offset value after generation stops, i.e., the start offset value remains fixed, therefore, every
time generation is restarted, time code output will always begin with the same start offset
value.
MA-4
M 20 ADDENDUM 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
M 20 So ft w a r e Ve r s io n 2
DIGITAL SCRUB: “DIG SCAN: ON/OFF, NN d B”
A Digital Scan page has been added to the Utility pages. This allows the user to have
control over digital audio output when in jog/ shuttle mode. The output may be attenuated
in 6 dB increments (0 dB to –42 dB).
Note the following when using Aux Track routing:
·
·
Aux routing play back through the “AUX” selected channels is defeated when Digital
Scan mode is enabled.
Cue and review scanning will always output audio at –6 dB regardless of the DigScan
status and the attenuation setting.
I/O CARD AS THE DIGITAL SOURCE
·
The “D” indicators in the Meter Display are now always lit solid when the Digital
Source is I/ O Card and the Clock Source is from a source other than I/ O Card (even
when the selected clock source is not present).
·
When the Digital Source is set for I/ O Card, there are some limitations on the routing.
Basically, the AES/ EBU and analog input share the routing, i.e., they are one in the
same. What this means is that when the Dig Source = I/ O Card, only I/ O Card routing
(1/ 2 à 3/ 4, 5/ 6, 7/ 8, 1-4 à 5-8, or 1-8 à 1-8) is allowed. The analog input routing will
not be editable and will follow (be the same as) the I/ O Card routing. If control of
analog input routing is desired, the digital source cannot be I/ O Card. Also, note that if
the user wants to mix the I/ O Card and analog inputs, Input Routing mode must be set
to 1-to-1.
SM P T E CHASE W ITH THE STOP BUTTON
If currently chasing SMPTE, pressing the Stop button will now stop the tape and disable
SMPTE Chase.
TAP E T C UP DATING W HEN IN INP UT M ODE
When the TC Track is input enabled, the SMPTE Rate will not automatically change when
transitioning from an area of tape with no tape TC into tape TC.
VARI-SP EED AND P ULL-UP /DOW N
When the M20 is set for a pull-up/ down, changing the pitch mode to VARI (by pressing
Pitch Mode or by entering a non-zero vari-speed value) now disables the pull-up/ down.
Likewise, when the M20 is in vari-speed, enabling pull-up/ down returns the M20 to FIXED
pitch mode operation.
M 20 ADDENDUM 2.1
MA-5
Download from Www.Somanuals.com. All Manuals Search And Download.
M 20 So ft w a r e Ve r s io n 2
M IDI T HRU
“Soft” MIDI Thru (automatically echoing non-F0 commands) is now defeated in order to
accommodate a MIDI closed loop more effectively.
NEW UTILITY P AGE ORDER
The Utility menu page order in version 2.00 has changed as follows:
Utility Pages
1 Dig Out
2 Online Source
14 Mute Until Lock
15 Dynamic Punch
16 Track Groups
17 RMD Error LEDs
18 Dig Scan
19 Save data to tape?
20 Load data from tape?
21 Tape Type
3 RS-422 Track Arm
4 RS-422 Mapping
5 Online Control
6 One-Button Record
7 Input Monitor
8 Unthread Timeout
9 TC Output Level
10 Rew/Fwd TC Out
11 XFade Time*
22 ID status
23 User Bits
24 Error Rate
12 Search Enable
13 Loc(ate) Before Play
25 Front Panel
26 Main
CADI DISP LAY CHANGES
·
Machine-specific Utility pages 21 (Tape Type), 23 (User Bits), 24 (Error Rate), 25 (Front
Panel), and 26 (Main) now indicate “See Local” in the CADI display.
·
When the master M20 (ID 1) parks at a locate point before other slaves have completed
the locate, the CADI now continues to indicate a locate in progress by flashing the
Locate or Locate 0 buttons. The stop is also lit solid to indicate the master is stopped.
·
The CADI now displays the more general “Select digital src trks” message when
routing digital input, since a system can have several M20s with various digital input
sources.
Version 2.10 Features
CASSET T E AUTO-INJECT
The M20 now has an inject command. When a cassette is partially inserted (as is the case
when a cassette remains in the transport door after an eject command), it is possible to
remotely load the cassette into the transport by pressing the Peak Mode and Eject buttons
simultaneously. Auto-Inject works from the M20’s front panel or from the CADI.
MA-6
M 20 ADDENDUM 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
M 20 So ft w a r e Ve r s io n 2
DECK STANDBY M ODE
A deck standby mode has been added as a user-optional transport load condition. Place the
M20 in Deck Standby by pressing the Peak Mode and Stop buttons simultaneously. In this
mode, the cassette remains loaded in the transport and the tape is completely withdrawn
into the cassette. When the tape is withdrawn, the drum is turned off and drum hours do
not accumulate. The counter display will indicate “DECK STANDBY” until it is refreshed
by another operation; however, the transport will remain in standby. Pressing any
transport control button (Rew, FFwd, Stop, Play, Rec, Loc, Loc 0,) will first rethread the
tape, then perform the selected transport operation.
AUTO-P ARK AFT ER FORM ATTING
When a tape format is completed by reaching the end of tape, the tape will autolocate to
00:00 ABS time and park, i.e., enter deck standby mode until another transport operation is
performed.
DEFERRED EJECT
Deferred Eject has been added. Pressing Eject when a locate is in progress will defer the
Eject action until the locate is complete. Pressing Eject twice before the locate is completed,
will abort the locate and result in an immediate tape eject.
NEW RS-4 22 DEVICE ID
The M20's RS422 device ID is now a BVW-75 instead of a BVU-950. Many Sony 9-pin
editor/ controllers will identify the M20 as this standard Betacam SP videotape recorder.
Changing the ID to the BVW-75 specifically improves performance with AVID’s Media
Composer Version 7.1.
IM P ROVED SM P T E CLOCK SOURCE RECOGNITION
The algorithm for determining if a SMPTE clock is valid has been improved to increase
transport and drum motor performance.
SAM P LE RATE CHANGE DURING P LAY/RECORD
Sample rate can no longer be changed when the tape is in Play or Record. This guarantees
the output of MTC at the proper frequency for the selected sample rate.
M 20 ADDENDUM 2.1
MA-7
Download from Www.Somanuals.com. All Manuals Search And Download.
|