Aiwa Stereo System XR DV700 User Manual

OPERATING INSTRUCTIONS

MANUAL DE INSTRUCCIONES

MODE D'EMPLOI

En (English)

E (Español)

F (Français)

DVD Stereo

System

XR-DV700

For assistance and information

(United States and Puerto Rico)

8B-CQA-903-01

010420ACK-U-M

Download from Www.Somanuals.com. All Manuals Search And Download.

Overloading — Do not allow anything to rest on the power

cord. Do not overload wall outlets and extension cords as

this can result in fire or electric shock. Do not locate this unit

where the cord will be abused by persons walking on it.

Lightning

TABLE OF CONTENTS

For added protection for this unit receiver during a lightning

storm, or when it is left unattended and unused for long periods

of time, unplug it from the wall outlet and disconnect the

antenna or cable system. This will prevent damage to the unit

due to lightning and powerline surges.

PRECAUTION ...................................... 2

PREPARATION .................................... 5

PARTS AND CONTROLS ......................... 8

ADJUSTMENT BEFORE OPERATION ......... 12

PLAYING DISCS

Outdoor Antenna

Power lines — An outside antenna system should not be

located in the vicinity of overhead power lines or other electric

light or power circuits, or where it can fall into such power

lines or circuits. When installing an outside antenna system,

extreme care should be taken to keep from touching such

power lines or circuits as contact with them might be fatal.

Outdoor Antenna Grounding — If an outside antenna or

cable system is connected to the unit, be sure the antenna or

cable system is grounded so as to provide some protection

against voltage surges and built-up static charges. Section

810 of the National Electrical Code, ANSI/NFPA No.70,

provides information with regard to proper grounding of the

mast and supporting structure, grounding of the lead-in wire

to an antenna discharge unit, size of grounding conductors,

location of antenna-discharge unit, connection to grounding

electrodes, and requirements for the grounding electrode. See

the figure.

Maintenance

Cleaning — Unplug this unit from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners. Use

a damp cloth for cleaning.

PREPARATORY INFORMATION ......... 14

BASIC PLAYBACK ........................ 15

SELECTING TRACKS/CHAPTERS ....... 17

OTHER PLAYBACK MODES .................. 18

DVD FEATURES ........................... 20

STATUS DISPLAY ......................... 22

DOLBY AND DTS SURROUND ................ 23

RADIO ............................................ 25

SOUND ........................................... 27

TIMER ............................................ 28

EXTERNAL EQUIPMENT ....................... 30

CUSTOMIZING DVD SETUP ................... 31

REFERENCE ..................................... 38

Damage Requiring Service

Unplug this unit from the wall outlet and refer servicing to

qualified service personnel under the following conditions:

1)When the power cord or plug is damaged or frayed.

2)If the liquid has been spilled into the unit.

3)If the unit has been exposed to rain or water.

4)If the unit does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions as improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the unit to normal operation.

5)If the unit has been dropped or the cabinet has been

damaged.

6)When the unit exhibits a distinct change in performance -

this indicates a need for service.

Antenna Grounding According

to the National Electrical Code

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE

UNIT

(NEC SECTION

810-20)

Do not attempt to service this unit yourself as opening or

removing covers may expose you to dangerous voltage or

other hazards. Refer all servicing to qualified service personnel.

Replacement Parts — When replacement parts are

required, be sure the service technician has used replacement

parts specified by the manufacturer or having the same

characteristics as the original part. Unauthorized substitutions

may result in fire, electric shock or other hazards.

Safety Check — Upon the completion of any service or

repairs to this unit, ask the service technician to perform safety

checks to determine that the unit is in proper operating

condition.

GROUND CLAMP

ELECTRIC

SERVICE

GROUNDING

CONDUCTORS

(NEC SECTION

810-21)

EQUIPMENT

POWER SERVICE

GROUNDING

GROUND CLAMPS

NEC-NATIONAL ELECTRICAL CODE

ELECTRODE SYSTEM

(NEC ART 250 PART H)

Download from Www.Somanuals.com. All Manuals Search And Download.

System and accessories

OWNER'S RECORD

Record the model number and serial number of your set

(found at the rear of your set) below. Refer to them when

contacting your Aiwa dealer.

XR-DV700

CX-LDV700 DVD stereo system

SX-L700 Five Surround speaker system (front speakers,

surround speakers, center speaker)

TS-LW700 Subwoofer

Remote control

Lithium battery (CR2025)

Model No. _____________________________

Serial No. _____________________________

FM antenna, AM antenna

Connecting cord (DIN 8-pin)

Video connecting cord

Front speakers cord (approx. 4 m / 13 ft.) × 2

Surround speaker cord (with plugs, approx. 8 m / 26 ft.) × 2

The red plug is for the right channel and the white plug is for

the left channel.

Center speaker cord (with an orange plug, approx. 3 m /

10 ft.) × 1

Pedestal × 2

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION

To attach the front speaker to the pedestal

Placing the main unit

Allow 15 cm (6 in.) clearance from the top of the unit for

movement of the disc compartment lid.

Placement

Place the speakers in their proper position. All speakers for a

full 5.1-channel home theater come supplied with your DVD

system.

Attaching the anti-skid patches

To prevent the surround and center speakers from slipping,

attach the supplied anti-skid patches to the bottom of the

speakers. Use 3 patches for each of these speakers.

To mount the surround speakers on the wall

Mount each speaker on a spot that can hold its weight.

AIWA disclaims any responsibility for injury to persons

or other accidents caused by not fitting the surround

speakers properly or if the place of the installation is not

suitable.

L&R: Front speakers (marked "FRONT")

C: Center speaker (marked "CENTER")

Place it in the center of the two front speakers, possibly on or

below the TV set.

LS&RS: Surround speakers (marked "REAR")

Place them directly to the side of or slightly behind the listening

area. Align them horizontally, preferably about 1 meter (3 feet)

above ear height.

SW: Subwoofer

Place it on the floor close to a wall or in a corner of the room.

•Either of the two front speakers can be used as the right or

the left one; likewise for the surround speakers.

•Do not place the left and right front speakers close to the TV

set, as doing so may cause picture noise.

•Sound output from the center and the surround speakers is

only available when the Dolby or the DTS surround system

is activated with the appropriate setting.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connection

Plug in the AC power cord to the AC power outlet after all other

connections are made.

Center speaker

Surround speaker

TV set

Surround speaker

Subwoofer

Front

speaker

Front

speaker

Download from Www.Somanuals.com. All Manuals Search And Download.

•Do not connect other equipment to the TO TS-LW700U

jack because this is used exclusively for the supplied

subwoofer.

The automatic demonstration will run on the display while

the power is turned off.

To deactivate the automatic demonstration, press DEMO/

ECO. The clock will flash on the display. For setting the

clock, see page 13.

Connect the bare ends of each speaker cord to

the corresponding speaker.

Be sure to use the correct cord for each speaker.

- Front speaker cords have bare leads at both ends

(approx. 4 m / 13 ft.).

- Surround speaker cords are the longer cords with a plug

at one end (approx. 8 m / 26 ft.).

The red plug is for the right channel and the white plug

is for the left channel.

Connect the supplied antennas.

Connect the FM antenna to the FM 75 Ω terminals and

the AM antenna to the AM LOOP terminals.

•Do not short-circuit the 0 and 9 speaker cord leads.

•Do not leave objects generating magnetism or objects

affected by magnetism near the speakers.

FM antenna

- Center speaker cord is the short cord with an orange

plug at one end (approx. 3 m / 10 ft.).

The copper-colored cords go to the 0 terminal of each

speaker.

Remote control

While sliding the latch, pull out the battery holder from the

bottom of the remote control. Place the supplied battery on

the battery holder with correct polarity. Finally, insert the holder

back into position.

Connect the cords from the front speakers to the

appropriate terminals on the subwoofer.

- Right front speaker: FRONT R terminals

AM antenna

- Left front speaker: FRONT L terminals

The copper-colored cords go to the 0 terminals.

Connect the television set.

If your TV set has an S-video input jack:

Connect the S-VIDEO OUT (S1) jack of this unit and the

S-video input jack of your TV with an optional S-video

connecting cord.

If your TV set does not have an S-video input jack:

Connect the VIDEO OUT jack of this unit and the video

input jack of your TV with the supplied video connecting

cord (the one with plugs at both ends).

Refer also to the Operating Instructions of your TV set.

The illustration shows the connection to the VIDEO OUT

jack.

•Replace the battery with a new one when the operational

distance between the remote control and main unit becomes

shorter.

•Remove the battery if the unit is not going to be used for an

extended period of time.

•The remote control may not operate if it is used under intense

sunlight or if its line of sight is obstructed.

Connect the cords from the surround speakers

to the appropriate jacks on the subwoofer.

- Right surround speaker: SURROUND R jack (red)

- Left surround speaker: SURROUND L jack (white)

Caution!

•If your TV set is a wide-screen set: you need to adjust

the TV aspect setting later (see “TV Aspect”, page 33).

•Do not use more than one connection to connect your

TV.

•Do not keep the battery near metallic objects such as rings,

bracelets, and keys. It may cause the battery to short circuit.

•After removing the battery, be sure to keep it out of reach of

children. In case it is swallowed, consult a doctor

immediately.

Connect the cord from the center speaker to the

CENTER jack (orange) on the subwoofer.

Connect the subwoofer to the main unit.

Connect the FROM CX-LDV700U jack of the subwoofer

to the TO TS-LW700U jack with the supplied connecting

cord (DIN 8-pin).

Connect the power supply.

Plug in the AC power cords of the main unit and the

subwoofer to AC outlets.

Download from Www.Somanuals.com. All Manuals Search And Download.

PARTS AND CONTROLS

Main unit: front

2 TUNER/BAND

8 VOLUME/MULTI JOG

Adjusts the volume.

Selects radio function and the radio band.

Changes the menu item selection in the MODE setting.

AUX

MODE

Selects AUX function.

Adjusts various mode and sound settings. Press

repeatedly to select among T-BASS, BASS, TREBLE,

SLEEP and TIMER.

DVD/CD

Selects DVD/CD function.

ENTER

3 zOPEN/CLOSE

Enters the item selected with MULTI JOG.

Opens and closes the disc compartment.

4 PHONES jack

Plug in here an optional headphones set with a stereo

mini plug (ø3.5 mm, ¹/8 in.). Speaker output is canceled.

5 POWER 6STANDBY/ON

Switches the unit on and off (standby).

1 aSET

Disc: pauses playback.

Radio: stores the received station to preset.

6 DEMO/ECO

When the unit is turned off: selects ECO mode, DEMO

mode or displays the clock.

When the unit is turned on: selects DEMO mode.

sCLEAR

Disc: stops playback.

Radio: clears a station preset.

DISPLAY

Disc: displays the title/chapter/track number being played

and remaining time of play.

Radio: displays the frequency of the tuned station.

cPRESET

Disc: starts playback.

Radio: tunes into a preset station.

COLOR

Selects the display color.

frDOWN, gtUP

Disc: skips to a previous or a succeeding chapter/track

when pressed, searches a title/track in fast forward or

fast reverse playback when held down.

7 SURROUND

Turns on the Dolby or DTS decoder. Press repeatedly to

select a listening mode.

Radio: manually tunes down or up within the band.

Download from Www.Somanuals.com. All Manuals Search And Download.

Main unit: rear

Subwoofer

2 AM LOOP, FM 75 Ω terminals

Plug in the supplied AM and FM antennas here.

3 TO TS-LW700U jack

Connect the supplied powered subwoofer here.

4 AC power cord

5 LINE OUT jacks

Outputs analog sound signals to external equipment.

6 AUX jacks

Accepts analog sound signals from external equipment.

1 VIDEO OUT jack

Outputs standard (composite) video signals.

7 FRONT 3 terminals

S-VIDEO OUT (S1) jack

Outputs S-VIDEO signals.

Connect the supplied front speakers here.

8 CENTER 3 jack (orange)

DIGITAL OUT (OPTICAL) jack

Outputs digital audio signals to external digital

equipment. Keep the jack covered with the supplied dust

cap when it is not being used.

Connect the center speaker here.

SURROUND 3 jacks (red or white)

Connect the surround speakers here.

9 FROM CX-LDV700U jack

Connect the main unit here with the supplied connecting

cord (DIN 8-pin).

CAUTION

NEVER play a multichannel Dolby Digital or a DTS

source through external digital equipment without a

Dolby Digital or a DTS decoder, respectively. Doing

so will generate high level noise which may be

harmful to your ears and damage the speakers.

0 AC power cord

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote control

vVBb

SUB TITLE ON/OFF

Changes the menu item selection.

Switches the subtitle on and off (DVDs only).

ENTER

T-SEARCH

Enter the selected item.

Enters the time search mode to locate a point in the disc

by specifying the title number, chapter number or the

playback time (DVDs only).

Displays the menu for DVDs.

MARK

SETUP

Enters the Mark mode to mark a point in the disc or to

start playback from a marked point (DVDs only).

During stop: enters the setup menu.

During playback: changes the playback time display of a

disc.

ANGLE

Selects the angle to view the scene (DVDs only).

SURROUND

REPEAT

Enters repeat playback mode.

RETURN

Returns to the previous menu screen. Displays the menu

for VCDs.

RANDOM/PRGM

Enters random or programmed playback mode (CDs and

VCDs).

SHIFT

Buttons with same or similar names with the main unit basically

have the same function.

Hold down when pressing a numbered button to change

its function to that printed above the number.

PBC

1 0-9, +10

Switches PBC(Playback Control) on and off for VCDs.

•e.g., "Press SHIFT+TIMER on the remote control"

means to hold down SHIFT and press 0/TIMER to use

the button for the timer function.

Disc: selects a title/chapter/track of the specified number.

Selects a menu item for VCDs with PBC.

Radio: tunes in to the station with the specified preset

number.

TIMER

Enters timer setting mode.

4 The following buttons take on these functions when pressed

SLEEP

Enters sleep-timer setting mode.

together with SHIFT:

Clears the Mark memory, etc.

MONO TUNER

Switches between stereo or monaural FM reception.

CLOCK

Enters clock adjustment mode.

2 The numbered buttons take on these functions when pressed

together with SHIFT:

ZOOM

Enlarge the picture (DVDs only).

3 T-BASS

Emphasizes low frequency sound.

AUDIO SELECT

Changes audio tracks (DVDs) or channels (VCDs).

TITLE

Displays the title menu for DVDs.

SUB TITLE SELECT

Changes the subtitle language (DVDs only).

Download from Www.Somanuals.com. All Manuals Search And Download.

Display window

CENTER(+, -)

7 T-BASS level indicators

Adjusts the sound level of the center speaker for Dolby

and DTS surround.

Displays the T-BASS level.

8 Disc type indicators

REAR(+, -)

Adjusts the sound level of the surround speakers for

Dolby and DTS surround.

Indicates the type of current disc (CD or VCD).

9 Track/preset number indicator

Displays the track number of CD or VCD and preset

number of radio. The current track/preset number flashes.

MAN/SEL (Manual/Select)

Enters speaker level and delay time setting mode.

0 Output type indicators

5 f/rDOWN

cPRESET

g/tUP

aSET

The surround playback mode indicators ("DOWNMIX"

and "hPRO LOGIC") indicate the surround output type

in which the source is actually being played.

The "OVER" level indicator lights up when external input

level from the AUX jacks is too high.

1 Disc indicators

! MONO/1(stereo) indicators

sCLEAR

Rotates during playback. Lights up during stop.

"DISC" lights up while the disc is loaded.

Indicates the type of radio reception.

6 POWER

7 TUNER BAND

AUX

@ SLEEP indicator

2 Audio signal type indicators

Lights up when the sleep function is active.

Indicates the signal type of the current audio track.

3 Main display

DVD/CD

Shows general information such as the active function,

current adjustment mode, title/chapter/track number,

elapsed time, radio frequency, or the time.

ON SCREEN DISPLAY

Displays disc playback status on the TV screen.

8 VOLUME (N,M)

4 5 indicator

Lights up when the timer function is active.

5 Playback mode indicators

Lights up to show the programmed, repeat, and random

playback modes.

6 KARAOKE indicator

Lights up when playing Dolby Digital karaoke disc.

Download from Www.Somanuals.com. All Manuals Search And Download.

ADJUSTMENTS BEFORE OPERATION

When power economizing mode is activated

When the unit turns off, "ECO MODE" is displayed for 4

seconds, and everything on the display clears.

Only the red indicator on the POWER button lights to show

that power is being supplied to the unit.

Standby power consumption

When power economizing mode is activated: 0.7 W

When power economizing mode is deactivated: 9 W

Power

DEMO

Press POWER 6STANDBY/ON (POWER on the

If the clock has not been set, "DEMO" appears on the display

remote control) to turn the unit on and off.

when the unit is turned off.

To deactivate the DEMO

While "DEMO" is displayed, press DEMO/ECO. The clock

flashes. For setting the clock, see page 13.

Volume

Turn VOLUME/MULTI JOG, or press VOLUME

N,M on the remote control.

Adjust from 0 (minimum) to 30 and MAX (maximum).

ECO mode

•Volume level setting is retained during power-off standby.

If the unit is turned off with the volume set to 21 or more, it

is automatically turned down to 20 the next time the unit is

turned on.

Reduces power consumption with the following operations.

After clock is set, this unit allows you to regulate its power

consumption by displaying nothing on the display while the

power is off. This is called power economizing mode.

Press DEMO/ECO while the unit is turned off.

Each press of this button changes the display status as follows:

1 Demo display (power economizing mode canceled)

2 Power economizing mode

3 Clock display (power economizing mode canceled)

Pressing a or ENTER turns on the backlight for 4

seconds.

Download from Www.Somanuals.com. All Manuals Search And Download.

Select color mode

Changing the display color

Setting the clock

The display color can be selected from among the preset colors

(Select color mode). 12 type of colors has already preset and

5 type of colors can be adjusted to your taste. In addition, the

display color can be selected for each function. (Function color

mode).

Press COLOR to display "SEL-COLOR" while the

power is on.

Press SHIFT+CLOCK on the remote control.

When the unit is turned off, you can also press a or

ENTER.

Within 4 seconds, turn VOLUME/MULTI JOG to

select the color.

Press f or g to set the time.

Each press changes the time in 1-minute steps.

Holding these buttons down will vary the time in 10-minute

units.

The selected color is automatically set after 4 seconds. It

is also set when pressing ENTER within 4 seconds. In

this case, "SET-COLOR" is displayed.

Adjust the preset colors

Press COLOR to display "SEL-COLOR" while the

If f or g is not pressed within 4 seconds, setting

is canceled.

•You can also turn VOLUME/MULTI JOG to the right to

advance the time and to the left to move the time back.

The speed with which the time changes varies according

to how fast you turn VOLUME/MULTI JOG.

power is on.

Function color mode

Within 4 seconds, turn VOLUME/MULTI JOG until

"COLOR M 1" to "COLOR M 5" is displayed.

Hold down COLOR until "-F-COLOR" is displayed.

Within 4 seconds, turn VOLUME/MULTI JOG to

select the source.

The source name and color number flashes on the display.

Within 4 seconds, press COLOR.

"50_50_50" is displayed and the left "50" flashes.

Press a or ENTER.

The time display stops flashing and the clock starts from

00 seconds.

Press DISPLAY repeatedly to select the color to

be adjusted.

Press ENTER.

The source name stops flashing.

- Left "50": adjust amber color.

- Center "50": adjust green color.

- Right "50": adjust blue color.

The selected item flashes.

Turn VOLUME/MULTI JOG to select the color.

To display the time while the power is on

Press SHIFT+CLOCK on the remote control.

The time will be displayed for 4 seconds.

Press ENTER.

"SET-COLOR"is displayed and the color number stops

flashing.

To switch to the 24-hour standard

Display the time and press s within 4 seconds.

With each press, the clock alternates between 12- and 24-

hour standard time.

Turn VOLUME/MULTI JOG to adjust the color.

The level can be adjusted from "00" to "50". "50" is

the brightest level.

Repeat steps 2 to 5 to set the colors for other

sources.

Repeat steps 4 and 5 to set the desired color.

Changing the color mode

Tip:

Press ENTER.

"SET-COLOR" is displayed.

In the 12-hour standard, "AM12:00" indicates midnight and

"PM12:00" noon.

Hold down COLOR until "ON COLOR" and "OFF

COLOR" flash alternately.

"ON COLOR" and "OFF COLOR" flash after "-F-

COLOR" is displayed.

- ON COLOR: function color mode

- OFF COLOR: select color mode

•If power is interrupted for more than approximately 12 hours,

all settings stored in memory after purchase need to be reset.

•If you select "00" in each color, it displays no color on the

display.

If the clock display flashes when the unit is turned

off

There has been a power interruption. Reset the clock.

•The display color may not change when you adjust only

one of the colors.

Release COLOR while the desired mode flashes.

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYING DISCS—PREPARATORY INFORMATION

Read the following information before playing discs.

Software dependent features of DVDs Types of VCDs

Video CDs equipped with PBC (Version 2.0)

PBC (PlayBack Control) allows you to select and play back

tracks via menu operations. High-resolution stills can also

be played back if available.

and VCDs

Supported disc formats

Since playback operations of DVDs and video CDs may be

intentionally fixed by software manufacturers, some playback

features of this player may not be available. For example, some

DVDs may not allow the pressing of STOP, r, t, or

other buttons at certain points in the disc. “ ” appears on

the TV screen if you press a button that cannot be used.

Refer to the instructions supplied with the disc.

This unit plays discs with the following logos.

DVDs

(12 cm disc)

Video CDs not equipped with PBC (Version 1.1)

These older types of VCDs are operated in the same way as

audio CDs.

Video CDs (VCDs)

(8 cm disc/12 cm disc)

•In some cases, you may want to play back VCDs equipped

with PBC with the PBC feature off. This is because some

disc playback features can only be used for VCDs without

PBC. See "Disabling PBC", page 16.

Audio CDs

(8 cm disc/12 cm disc)

Subdivision of discs

Title (DVD only)

•The unit may not play a CD-R/RW disc recorded on personal

computers or certain kinds of CD-R/RW recorders.

•Do not attach adhesive label, etc. to either side of a CD-R/

RW disc, as doing so may cause malfunction.

•Do not load an unrecorded CD-R/RW disc. The disc may be

damaged.

Largest subdivision of a DVD; a movie for video software, or

an album for audio software.

It is forbidden by law to copy, broadcast, show, broadcast via

cable, play in public, or rent copyright material without

permission.

Chapter (DVD only)

Sections within a title. A title is usually made up of several

chapters.

•Do not use irregular-shaped CDs.

Track (audio CD and VCD only)

Copy protection signals are included in some DVD and VCD

discs. If video recording equipment is connected directly or

indirectly to the video output of this unit, picture noise may

appear when playing back such discs. Recording of such discs

made on a VCR will also have picture noise.

Sections within an audio or video CD.

Color system for DVDs and VCDs

Scene (VCD with PBC only)

This unit conforms to the NTSC color system.

If the VCD of PAL color system is played, sometimes the

picture is distorted.

Sections within a VCD with the PBC function. Scenes are

displayed in tiles on the menu screen, each with a scene

number for easy selection.

This product incorporates copyright protection technology that

is protected by method claims of certain U.S. patents and other

intellectual property rights owned by Macrovision Corporation

and other rights owners. Use of this copyright protection

technology must be authorized by Macrovision Corporation,

and is intended for home and other limited viewing uses only,

unless otherwise authorized by Macrovision Corporation.

Reverse engineering or disassembly is prohibited.

DVD region code

This unit is designed and manufactured for playback of region

“1” encoded DVD software. Region code appears on most

DVD labels to indicate which type of player can play the disc.

•A DVD without a “1” or “ALL” on its disc label cannot be

played on this unit. If you try to play such a disc, the message

“REGIONAL CODE VIOLATION” will appear on the TV screen.

•Some DVDs may not be properly labeled with a region code,

although they may in fact be region encoded and thus limited

in its playback area.

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYING DISCS—BASIC PLAYBACK

•Do not open or close the disc compartment forcibly by hand.

If "LID ERR" is displayed, unplug the AC power cord and

contact your AIWA dealer.

•Do not place more than one disc.

•Do not tilt the unit with a disc loaded.

•Do not touch the pickup lens. If it is soiled, discs may not

be played normally.

To remove the disc

Press zOPEN/CLOSE in stop mode to open the disc

compartment. Then pull out the disc while pressing the center

pivot.

To play DTS audio CDs

Hold down SURROUND to select "DTS MODE". "

MODE" lights up. Otherwise, high-level noise will be

produced which may harm both your hearing and the unit.

Basic playback operation common to DVDs, audio CDs, and

Playing discs

video CDs are described in this section.

If "PCM CD" and the elapsed playback time

indication appear alternately in the display

You are trying to play a regular (PCM) audio CD when the

unit is in the DTS mode. Hold down SURROUND to select

"PCM MODE".

Press DVD/CD.

Check your TV connection first

•Make sure the TV set is connected and its input source is

selected properly.

Press z OPEN/CLOSE to open the disc

compartment.

Place a disc with the label side up. Then close the disc

compartment.

•Various guide displays of the current operation are available

on the TV screen. To view them, make sure you have “Guide

Message ON” in the Setup menu (see “Guide Message”,

page 32).

•You can select the language for the guide message out of 3

available languages (see “Menu Language”, page 32).

Pivot

zOPEN/CLOSE

Press c.

For a DVD, or a VCD with PBC, playback starts

automatically when the disc is loaded.

Download from Www.Somanuals.com. All Manuals Search And Download.

Playing back with the software

Stopping and pausing

Disabling PBC (VCD only)

To stop playback

Press SHIFT+PBC on the remote control.

"PBC" disappears from the display, and the menu playback

feature is disabled.

specific menu (DVDs and VCDs only)

Press s.

This unit supports the menu interface of DVDs, and VCDs with

PBC. The menu screen may be displayed automatically when

the disc is loaded.

Playback stops. The unit remembers the point at which

playback stopped.

•With PBC disabled, VCDs are played just like audio CDs.

This allows you, for example, to use repeat playback and

programmed playback for VCDs with PBC.

•If PBC is pressed during playback, playback stops.

•See also “Types of VCDs”, page 14.

Use the remote control.

To resume playback from the point where it stopped

Press c.

“RESUME” appears on the TV display and playback starts

where it last stopped (Resume function).

DVDs

Press vVBb to select your desired program.

Press ENTER to begin playback.

To clear the point to be resumed

Press s again during stop.

To display the menu

Press TITLE or MENU during playback or stop.

“RESUME OFF” appears on the TV display. The resume

memory is cleared, and playback starts at the beginning of

the disc when c is pressed.

VCDs

To select a program from the menu

Press the number button(s) to select your desired

program.

Notes on the resume function

•The point to be resumed is also cleared when the disc tray

is opened, the current disc is switched, the power is turned

off, or the function is switched.

•The resume function is not available for PBC playback of

VCDs. To turn off PBC, see “Disabling PBC” below.

To display the menu

Press RETURN.

•For some DVDs you can select the menu language out of

the ones available. See “Disc Menu”, page 33.

•Contents and operation of the software specific menu vary

with the disc. Follow the instructions on the disc and on the

menu screen.

To pause playback

Press a.

To resume playback, press c.

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYING DISCS—SELECTING TRACKS/CHAPTERS

Skipping

Press f or g repeatedly during playback.

- With each press of g, the disc position skips to the

beginning of the succeeding tracks (CDs/VCDs) or chapters

(DVDs).

- With each press of f, the disc position skips back first

to the beginning of the current track, then to the previous

tracks (CDs/VCDs) or chapters (DVDs).

•Skipping may be disabled on some DVDs.

Basic operations to locate a desired point are described here.

Fast forward/reverse playback

DVDs can also be searched by other methods (see "Playing

discs—DVD features", page 20).

Hold down f or g during playback.

- DVDs: “fx 2” or “gx 2” is displayed on the TV

screen.

Direct selection (CDs and VCDs only)

- CDs and VCDs: “fx 5” or “gx 5” is displayed on

the TV screen.

Select a track directly by entering the track number on the

remote control.

To change playback speed

Press the numbered buttons for the desired track.

Example:

To play track 12, press +10, 2.

Hold down f or g repeatedly.

- DVD: playback speed changes among double speed, 8 times

and 32 times.

To play track 20, press +10, +10, 0.

Playback begins at the beginning of the selected track and

continutes to the end of the disc.

- CDs and VCDs: playback speed alternates between 5 times

and 16 times.

To return to normal playback

•For VCDs with PBC, turn off PBC first (see "Disabling PBC",

page 16).

Press

•There is no audio during fast playback (DVDs and VCDs).

•Fast playback speed is the value for a disc with an average

bit rate.

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYING DISCS—OTHER PLAYBACK MODES

Repeat playback

DVDs

Press SHIFT+REPEAT repeatedly on the remote

control during playback.

With each press, the repeat playback mode changes as follows:

- CHAPTER: repeats the current chapter.

- TITLE: repeats the current title.

- OFF: cancels repeat mode (normal playback)

"[" appears on the unit's display when the unit is in the

title repeat mode and "[ 1" appears in the chapter repeat

mode.

CD and VCDs

Press SHIFT+REPEAT repeatedly on the remote

control.

With each press, the repeat playback mode changes as

follows:

Frame advance (DVDs and VCDs only) Slow playback (DVDs and VCDs only)

Press a to pause playback.

Hold down f or g.

- ALL: repeats all tracks on a disc.

- TRACK: repeats the current track.

- OFF: cancels repeat mode (normal playback)

"[" appears on the unit's display when the unit is in

the all repeat mode and "[ 1" appears in the track repeat

mode.

Press a repeatedly to advance frames.

To return to normal playback

Press c.

To change the slow forward playback speed

Hold down g repeatedly.

The slow playback speed changes among 1/30, 1/15 and

1/5.

•There is no audio during frame advance.

Press c to start playback.

•Only 1/15 speed is available for slow reverse playback.

•For VCDs with PBC, turn off PBC first (see "Disabling PBC",

page 16).

To return to normal playback

Press c.

To cancel repeat playback

Press SHIFT+REPEAT on the remote control repeatedly until

"[" disappears on the unit’s display.

•There is no audio during slow playback.

To repeat playback of selected tracks

Program the tracks with the programmed playback function,

and then press SHIFT+REPEAT to repeat playback of the

programmed tracks.

Download from Www.Somanuals.com. All Manuals Search And Download.

To clear the program

Press s again during stop.

Programmed playback (CDs and VCDs

only)

Changing audio channels (VCDs)

Use this function when playing Karaoke VCDs or VCDs with

different sound tracks in the left and right channels.

•The program is also cleared when the disc tray is opened,

the function is switched or the power is turned off.

Up to 30 tracks can be played back in the order of selection.

Press SHIFT+AUDIO SELECT repeatedly during

playback.

With each press, the audio channel changes as follows:

- Lch: left audio channel is output from both front speakers

- Rch: right audio channel is output from both front

speakers

Press SHIFT+RANDOM/PRGM on the remote

control in stop mode.

To check the program

Press g during stop.

With each press, the program number and the track number

are shown progressively on the unit’s display.

“PROGRAM” appears on the TV screen and "PRGM"

flashes on the unit’s display.

Press the numbered button(s) on the remote

control for the track to be played first.

To select track 12, press +10, 2.

To add tracks to the program

Repeat step 2 in stop mode. The new tracks are added to the

end of the program .

- STEREO: normal stereo playback

•It is impossible to connect a microphone to this unit and

sing along to music sources.

To select track 20, press +10, +10, 0.

To skip tracks

•Audio tracks of DVDs can also be switched. See "Changing

audio tracks", page 21.

Repeat step 2 to program other tracks.

Press f or g repeatedly during playback.

Playback skips to the previous or the succeeding track(s)

within the program.

Press c to start playback.

The programmed tracks are played back in the order of

entry.

When programmed playback is complete or when s is

pressed to stop playback, the program display reappears.

Random playback (CDs and VCDs

only)

•For VCDs with PBC, turn off PBC first (see "Disabling PBC",

page 16).

Tracks can be played back randomly.

Press SHIFT+RANDOM/PRGM repeatedly on the

remote control to display "RANDOM" on the

unit's display.

•During programmed playback, you cannot select a track with

the numbered buttons.

•If the total playing time of the program exceeds 99 minutes

and 59 seconds, the playing time is displayed as

"- -:- -".

“RANDOM” appears on the TV screen.

Press c to start playback.

To stop programmed playback

Press s.

At this point, the program is not cleared. Pressing c will

restart programmed playback from the first programmed track.

To cancel random playback

Press SHIFT+RANDOM/PRGM once on the remote control.

“OFF” appears on the TV screen and "RANDOM"disappears

on the unit’s display.

•For VCDs with PBC, turn off PBC first (see "Disabling PBC",

page 16).

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYING DISCS—DVD FEATURES

To recall a marked point

Chapter search

1 Press SHIFT+MARK to enter the mark mode.

2 Press Bb to move the cursor or press a number button

for the memory (1 - 5) to select the desired mark memory.

3 Press ENTER or c.

Specify the playback location of a DVD by the chapter number.

Press SHIFT+T-SEARCH twice.

Press the numbered button(s) for the desired

chapter number, or press vV to change the

displayed chapter number.

Playback starts from the recalled point.

To clear a marked point

1 Press SHIFT+MARK to enter the mark mode.

2 Press Bb to move the cursor or press a number button

for the memory (1 - 5) to select the desired mark memory.

3 Press C.

Example:

To play chapter number 7, press 7.

To play chapter number 20, press +10, +10, 0.

To clear the number, press C.

If needed, press Bb to move the cursor to or from the

title number.

4 Press SHIFT+MARK again to exit the mark mode.

•A marked point is recalled with the subtitle and audio

language setting at the time it was marked, regardless of

possible later changes to the setting.

•When the 6th DVD disc is inserted, the mark data for the

oldest disc is overwritten by the disc information of the new

disc and deleted, even when a new point is not memorized.

Press ENTER or c.

Playback begins from the specified chapter.

Features unique to DVDs, such as marking, searching, and

switching of angles, subtitles, and audio tracks are described

here.

•If you specify a chapter number which does not exist in the

title, the symbol is displayed. Repeat from step 1 with a

valid chapter number.

Title search

Marking

Specify the playback location of a DVD by the title number.

Mark points in a DVD to be recalled later. You can mark up to 5

discs, each with up to 5 points.

Press SHIFT+T-SEARCH.

Press SHIFT+MARK while playing back the

desired point.

Press the numbered button(s) for the desired title

number, or press vV to change the displayed

title number.

“

” appears on the TV screen and the unit enters the mark

mode. The current mark memory is highlighted by the

cursor.

Example:

To play title number 2, press 2.

To clear the number, press C.

Press Bb if needed to move the cursor to the

desired mark memory.

Press ENTER or c.

Playback begins from the specified title.

A numbered mark memory is occupied. An asterisk

appears on a vacant one.

•If you specify a title number which does not exist on the

disc, the symbol is displayed. Repeat from step 1 with a

valid title number.

Press ENTER.

The current point is marked in the mark memory.

Press SHIFT+MARK again to exit the mark mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Time search

Changing subtitles

Changing audio tracks

Locate a point in the title by specifying the time from its Display the subtitles on the screen when playing DVDs which Some DVDs have more than one audio tracks, for example,

beginning.

contain them. Subtitle language can be changed if more than soundtracks in different languages, or different sound mixes of

one is available.

Press SHIFT+SUB TITLE ON / OFF during playback.

The subtitles will be displayed.The current subtitle number

and the number of available subtitles are displayed on the TV.

the same recording. You can change the audio track when

playing such discs.

Press SHIFT+AUDIO SELECT during playback.

Each time you press the button, the audio track will change.

The current audio track number and the number of available

audio tracks are displayed on the TV.

Press SHIFT+T-SEARCH 3 times while the resume

function is activated or during playback.

Press the numbered buttons to enter the time for

the desired point.

Example:

To change the subtitle language

Press SHIFT+SUB TITLE SELECT to select the desired subtitle

language.

To specify 1:17:30 (1 hour 17 minutes 30 seconds), press

1, 1, 7, 3 and 0.

To specify 0:08:07 (8 minutes 7 seconds), press 8, 0 and

•The audio track can be changed only if the disc contains

multiple audio tracks. The number of available audio tracks

varies with the disc.

•The audio track language first played is specified by the

audio language setting (see “Audio Language”, page 32).

To turn off the subtitles

Press SHIFT+SUB TITLE ON / OFF again.

To clear the numbers, press C repeatedly.

•If you press SHIFT+SUB TITLE ON / OFF when playing a

Press ENTER or c.

disc without subtitles, the

•The subtitle language can be changed only if the disc

contains more than one subtitle language.

•Some discs have subtitles on by default and does not allow

you to remove them.

•The subtitle language first displayed is specified by the

subtitle setting (see “Subtitle Language”, page 33).

symbol is displayed.

Listening Karaoke DVD discs

Press SHIFT+AUDIO SELECT repeatedly during playback to

select your desired Karaoke track.

Playback begins from the specified location.

•If you specify a time greater than the length of the title, the

symbol is displayed. Repeat from step 1 with a valid

time.

•It is impossible to connect a microphone to this unit and

sing along to music sources.

Note on searching

•Title, chapter, and time search will not work with discs that

do not support the search function.

Zoom

Press SHIFT+ZOOM during playback.

The picture around the center of the screen is enlarged to

approximately 4 times.

Changing angles

Select the angle to view a scene when playing back DVDs shot

with multiangles.

To move the enlarged picture

Press vVBb.

To return to the center of the picture, press C.

Press SHIFT+ANGLE repeatedly to select a viewing

angle.

With each press, the angle will change. The current angle

number and the number of available angles are displayed on

the TV.

To cancel zoom

Press SHIFT+ZOOM again.

•If you press SHIFT+ANGLE when playing back a scene or a

disc without multiple viewing angles, the

displayed.

symbol is

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYING DISCS—STATUS DISPLAY

DVDs only

shows the title number and the chapter number

On the TV

Press ON SCREEN DISPLAY repeatedly.

Various playback status information appear on the TV screen

along with icons that indicate the type of information.

shows the type of audio track

D: Dolby Digital signal. The numbers below

indicate the number of front and rear audio channels.

For example,

“2/0” = [Conventional stereo] two front channels (left

and right) and no rear channel

“3/2.1” [5.1-channel surround] = three front channels

(left, right and center), two rear channels (left rear and

right rear) and LFE (Low Frequency Effects).

Common to all types of discs

shows the elapsed playing time during playback; total

playing time or the playback resume point during stop

shows the repeat mode status

Audio and video CDs only

dts: DTS signal.

shows the track number

LPCM: Linear PCM signal. The sampling frequency

and the D/A conversion bits are displayed below, such

as “48k-16b”.

KARAOKE: Karaoke signal. The currently active vocal

track is displayed below, such as “VOCAL 1 + 2”.

MPEG: MPEG audio signal.

shows the current angle number out of the available

number of angles

Various disc playback status information can be displayed on

the unit's display and on the TV screen.

shows the program/ random playback mode status

shows if PBC is on or off (VCD only)

On the unit’s display

Press SETUP repeatedly during playback.

DISPLAY on the unit is also available.

With each press, the playback time display changes as follows:

Audio and Video CDs

shows the current subtitle number out of the available

number of subtitles

shows the occupied mark memory numbers

- Number and elapsed time of current track

- Number and remaining time of current track

- Elapsed time of disc

- Remaining time of disc

DVDs

- Number and elapsed time of current title

- Number and remaining time of current title

- Number and elapsed time of current chapter

- Number and remaining time of current chapter

•Playback time information cannot be changed during

random playback.

•In some discs, playback time information may not be

displayed correctly during programmed playback.

•Playback time information display is not available for VCDs

with PBC.

Download from Www.Somanuals.com. All Manuals Search And Download.

DOLBY AND DTS SURROUND

Playing surround sources

Press DVD/CD and play the Dolby or the DTS

surround disc.

DVDs may contain several audio tracks. If necessary, press

SHIFT+AUDIO SELECT to select the desired playback

track.

Press SURROUND.

The Dolby or the DTS decoder is enabled, depending on

the source, and the source is played with the surround

effect in the “NORMAL” listening mode.

The surround playback mode indicators light up according

to the signal type and other conditions (see “Surround

playback mode indication”, page 24).

This unit comes equipped with a Dolby Digital/Pro Logic decoder

and a DTS decoder. With the full 5.1-channel speaker system

supplied, Dolby and DTS surround sources can be played back

in full scale home theater sound.

Dolby Pro Logic is an analog audio encoding system with

To play audio from external video equipment in

surround sound

1 Press AUX and play the surround video source on the

external equipment.

four independent channels: left, center, right, and surround.

These four channels are coded into the two tracks of a

conventional analog stereo source.

Dolby Pro Logic software is marked with the

Hlogo.

2 Press SURROUND.

Dolby and DTS surround

To cancel surround playback

Press SURROUND repeatedly until “OFF” is displayed.

•Make sure all supplied speakers are placed and connected

properly (pages 5 to 7).

•Make sure your TV is connected properly and the appropriate

input is selected.

Dolby Digital and DTS are two different digital encoding

systems of audio signals.

To adjust the sound level of the speakers during

playback

See “To adjust the speaker level balance without the test

signal”, page 24.

Both Dolby Digital and DTS, in their full configuration, can

have a total of “5.1” discrete channels: left, center and right

front channels, separate left and right surround channels, plus

a low-frequency effects (LFE) channel, counted as “0.1”

channel.

Dolby Digital and DTS tracks may also come in 1 or 2 channels

(monaural or stereo, respectively), or in fact, any number of

channels within the limit. Sources with 3 or more channels

will be refered to hereon as a multichannel source.

•Dolby Digital, DTS, or the Dolby Pro Logic surround system

is canceled when the headphones are plugged in.

•Dolby or DTS Surround sound can only be obtained when

playing back a disc recorded in the respective system.

•To play DTS audio CDs, see "Playing discs", page 15.

Dolby Digital software is marked with the

logo.

DTS software is marked with the

logo.

Download from Www.Somanuals.com. All Manuals Search And Download.

•The channel will not change while you are adjusting the

sound level.

•A clicking sound might be heard with the test signal during

level adjustment. This is not a malfunction.

Adjusting speaker level

Additional Dolby and DTS surround

listening modes

For optimum performance, the sound level of all available

channels should be adjusted to suit your listening environment.

In addition to the NORMAL mode, this unit is also equipped

with the PHANTOM and the 3 STEREO modes.

To stop speaker level adjustment

Press s or MAN/SEL.

The left and right front speakers create the stereo effect.

The center speaker helps achieve precise sound positioning

over a broad sound field.

•These modes are to be used when either the center speaker

unit or the surround speaker units are not available, and

therefore, not be needed under the normal use of this DVD

system.

To adjust the speaker level without the test signal

1 Play the surround source.

2 Press SURROUND repeatedly to select the mode for your

speaker configuration.

3 Press SHIFT+MAN/SEL repeatedly on the remote control

until "L/R" is displayed.

4 Press f or g on the remote control to adjust the

sound level of the front speakers.

5 Repeat steps 3 and 4 to adjust the sound level of the other

speakers (S-W: subwoofer, C, RS, or LS).

The surround speakers enhance the “depth” of the sound field.

Adjusting with the test signal

The unit is equipped with a built-in test signal generator for

easy balance adjustment of the channels.

To change the listening mode

Press SURROUND repeatedly until the desired listening mode

is displayed. With each press, the listening mode changes as

follows:

Press SURROUND repeatedly to select the mode

for your speaker configuration.

- NORMAL

- For playback with the supplied speakers, select

"NORMAL".

- PHANTOM: select this mode when no center speaker is

connected. The center channel signals are output

through the left and right speakers.

- 3 STEREO: select this mode when no surround speakers

are connected. The rear channel signals are output

through the front speakers.

- OFF: select this mode when neither the center nor the

surround speakers are connected.Multichannel Dolby

Digital or DTS sources are played back in a 2-channel

downmix.

Hold down SHIFT+MAN/SEL on the remote

control until "L" flashes in the display.

The test signal travels through the channels one by one.

Indication for the currently adjustable channel flashes in

the display:

•SHIFT+CENTER +/- and SHIFT+REAR +/- buttons are also

available for the level adjustment of these channels. LS and

RS channels cannot be adjusted separately with the REAR

buttons.

•Speaker level adjustment is available only for speakers that

are activated.

- L: left front speaker

- C: center speaker

- R: right front speaker

•Speaker level setting is common to Dolby Digital, DTS, and

Dolby Pro Logic.

- RS: right surround speaker

- LS: left surround speaker

Surround playback mode indication

The surround playback mode indicators light up on the display

to show the actual surround playback mode.

- “hDIGITAL” shows that a multichannel Dolby Digital

source is played back in surround sound.

Press f or g on the remote control to

adjust the sound level.

- Left and right front speakers: press f to shift the

balance to the left and g to shift to the right.

- Center and the surround speakers: press f to de-

emphasize the channel and g to emphasize the

channel.

- “hPRO LOGIC” shows that either a 2-channel source

or a multichannel Dolby Pro Logic source is played back

in surround sound.

- “DOWNMIX” shows that a multichannel source is played

back in a 2-channel downmix.

Adjust the sound level so that the test signal from each

channel is heard with the same loudness.

Download from Www.Somanuals.com. All Manuals Search And Download.

RADIO

Adjusting delay time

Sounds from the surround speakers and the center speaker are

reproduced a split second after the front speakers for the effect

of depth.

Play the surround source.

- Delay time adjustment of the center channel is available

only when playing Dolby Digital or DTS multichannel

sources.

Press SURROUND repeatedly to select the mode

for the speaker configuration.

Press SHIFT+MAN/SEL repeatedly on the remote

control to select delay time to adjust.

- C _MS: delay time setting for center speaker

- S _MS: delay time setting for surround speakers

Manual tuning

Preset tuning

Press TUNER/BAND repeatedly to select a band.

The unit switches to the radio from any other function and

alternates between FM and AM.

Preset your favorite stations and tune them in directly.

Press f or g on the remote control to

adjust the delay time.

Center speaker: adjust the delay time so that screen dialogs

are heard clearly and naturally, between 0 ms

(milliseconds) and 5 ms in 1 ms steps. The default is

"C 0MS" (no delay).

Surround speakers

Dolby Digital/DTS: adjust between 0 and 15 ms in 5 ms

steps. The default is "S 5MS".

Presetting stations

Press TUNER/BAND to select the band.

Press fDOWN or gUP to tune in to a

station.

Press fDOWN or gUP to tune in to the

desired station.

"TUNE" is displayed when a station is tuned in.

"1" lights up for FM stereo reception.

Press aSET to store the station.

The preset number, beginning from "1", appears on the

display.

To search for a station automatically (Auto Search)

Hold down fDOWN or gUP.

The unit searches for a station up or down the band and stops

at reception.

Dolby Pro Logic: adjust to 15 ms, 20 ms or 30 ms. The

default is "S 20MS".

Repeat step 1 to 3 to preset other stations.

•Delay time setting in Dolby Digital/DTS affects that of Dolby

Pro Logic, and vice versa.

•Delay time adjustment is available only for speakers that

are activated.

•You cannot store more than a total of 32 preset stations.

"FULL" is displayed.

•If power is interrupted for more than approximately 12 hours,

To stop the search manually, press fDOWN or gUP.

•Auto Search may not stop at stations with weak signals.

all settings stored in memory after purchase need to be reset.

Download from Www.Somanuals.com. All Manuals Search And Download.

Tuning in to preset stations

Adjustments

On the unit

Antennas

Press TUNER/BAND to select the band.

Keep antennas away from metallic objects, electrical equipment

and cords.

FM antenna: Extend fully in a T-shape. If receiving condition

is poor, connect optional outdoor antenna to FM 75 Ω

terminal. Be sure to connect the shield braid of the antenna

to the 2 terminal.

Press cPRESET repeatedly.

With each press, the station with the succeeding preset

number is tuned in.

On the remote control

AM antenna: Rotate to find best reception.

Press TUNER/BAND to select the band.

To switch to monaural FM reception

Press SHIFT+MONO TUNER on the remote control. With each

press, "MONO" and "STEREO" are displayed alternately

on the display.

Press the numbered button(s) for the preset

number of your desired station.

- To select preset number 20, press +10, +10 and 0.

- To select preset number 15, press +10 and 5.

cPRESET is also available.

•When FM stereo reception is poor, switching to monaural

reduces noise.

To clear a preset station

1 Tune in to the station by preset tuning.

2 Press sCLEAR, then press aSET within 4 seconds.

Preset numbers of preset stations in the band with higher

numbers decrease by one.

To switch the AM tuning interval

Hold down TUNER/BAND and press POWER on the unit. With

each press, the AM tuning interval alternates between 9 kHz/

step and 10 kHz/step.

•The default is 10 kHz/step. Change it only when using the

unit in a 9 kHz/step area. Switching AM tuning interval clears

all the station presets.

Download from Www.Somanuals.com. All Manuals Search And Download.

SOUND

TREBLE

Adjusts the treble level.

Press MODE repeatedly to display "TREBLE".

Within 7 seconds, turn VOLUME/MULTI JOG to

adjust the treble level.

The treble level can be adjusted from "–5" to "+5".

•If the sound becomes distorted with the TREBLE effect,

cancel the effect.

Adjusting left/right speaker balance

Press SHIFT+MAN/SEL repeatedly on the remote

control until "L/R" is displayed.

T-BASS

BASS

Press f or g on the remote control to

adjust the balance.

Emphasizes low frequencies for a powerful sound.

Adjusts the bass level.

Press within 4 seconds.

On the main unit

Press MODE repeatedly to display "BASS".

•When surround playback is activated, level adjustment of

other speaker channels is available as well. See "Adjusting

speaker level", page 24.

Press MODE repeatedly to display "T-BASS".

Within 7 seconds, turn VOLUME/MULTI JOG to

adjust the bass level.

The bass level can be adjusted from "–5" to "+5".

Within 7 seconds, turn VOLUME/MULTI JOG to

select one of the three emphasis levels or the off

position.

•If the sound becomes distorted with the BASS effect, cancel

the effect.

On the remote control

Press T-BASS repeatedly to select one of the three

emphasis levels or the off position.

•If the sound becomes distorted with the T-BASS effect, cancel

the effect.

Download from Www.Somanuals.com. All Manuals Search And Download.

TIMER

Press f or g to set the timer-on time, then

press ENTER or a.

Press f or g to set the timer-activated

duration, then press ENTER or a.

With each press, the timer-activated duration changes in

5-minute steps between 5 to 240 minutes.

If there is no button input for 4 seconds, the current setting

is entered automatically.

•VOLUME/MULTI JOG is also available in place of f

or g.

Adjust the volume and tone for timer playback.

If the volume level is set to 21 or higher, it is automatically

turned down to 20 when the unit is turned on by the timer.

Prepare the source.

To play the disc, insert a disc.

Sleep timer

Timer playback

To play the radio, select the band and tune in the desired

station.

To play external equipment connected to the AUX jacks,

set an external timer for the equipment so that playback

begins at the same time.

Turns off the unit automatically after a specified time.

Turns on the unit at a specified time for the specified duration.

Make sure the clock is set correctly.

Press MODE repeatedly to display "SLEEP".

On the remote control, press SHIFT+SLEEP.

Select the desired playback source.

Press f or g repeatedly to set the sleep

timer duration.

On the main unit

1 Press MODE repeatedly to display " ".

2 Within 7 seconds, turn VOLUME/MULTI JOG

to display " PLAY".

Press POWER 6STANDBY/ON to turn the unit

off.

"5" remains on the display to indicate the timer standby

mode (when ECO mode is deactivated).

At timer-on time, the unit turns on and plays the selected

source. After the specified timer-activated duration, the

unit turns off again.

With each press, the timer duration changes in 5-minute

steps between 5 to 240 minutes. If there is no button input

while "SLEEP"is displayed, the current setting is entered

automatically.

The unit turns off after the selected time.

•VOLUME/MULTI JOG is also available in place of f

or g.

On the remote control

Press SHIFT+TIMER.

"5" indicator lights up and " PLAY" appears on the

display. The timer-on time and the source name along

with the timer-activated duration appear alternately on the

display.

•Timer playback will not begin unless the unit is turned off

first.

•Connected equipment cannot be turned on or off by the built-

in timer of this unit. Use an external timer.

To check the remaining time until the unit turns off

Press MODE repeatedly (press SHIFT+SLEEP on the remote

control). The remaining time is displayed for 7 seconds.

Within 4 seconds, press ENTER (aon the remote

control).

To cancel the sleep timer

Follow steps 1 and 2 above (press SHIFT+SLEEP twice on

the remote control) so that "SLEEPoFF" is displayed.

The timer-on time and the source name along with the

timer-activated duration appear alternately on the display.

Download from Www.Somanuals.com. All Manuals Search And Download.

To check the timer setting

Press SHIFT+TIMER on the remote control.

The timer-on time, the source and the timer-activated duration

are displayed for a while.

To change the timer setting

Reset the timer again.

To turn off the timer

On the main unit

Press MODE repeatedly to display " PLAY" and turn

VOLUME/MULTI JOG to display "

OFF". Then press

ENTER. "5" disappears from the display.

On the remote control

Press SHIFT+TIMER repeatedly until " OFF" is displayed.

"5" disappears from the display.

Tip:

Your timer setting is retained even if the timer is turned off.

Next time the timer is turned on, you can change your previous

setting, or simply use the same setting again.

Download from Www.Somanuals.com. All Manuals Search And Download.

EXTERNAL EQUIPMENT

Connection besides those described in section "Preparation"

are described here.

•See section "Parts and controls" for illustration.

•Connecting cords for optional equipment are not supplied.

•Refer also to the operating instructions of the connected

equipment.

LINE OUT jacks

CAUTION!! When connecting to digital equipment

without a Dolby Digital or a DTS decoder

NEVER play a multichannel Dolby Digital source through

connected digital equipment without a Dolby Digital

decoder.

Similarly, NEVER play a multichannel DTS source through

connected digital equipment without a DTS decoder.

Doing so will generate high level noise which may be

harmful to your ears and damage the speakers.

Outputs analog audio signals to connected

equipment.

Connect to the line input jacks of audio equipment

with an optional audio connecting cord with RCA

phono plugs (red plug to R jack, white plug to L jack).

•Consult your local Aiwa dealer for optional equipment.

•Do not connect the same equipment to the LINE OUT jacks

and AUX jacks of this unit. Noise will be generated by a

signal loop which may damage the equipment.

•Connecting the LINE OUT jacks to a TV may cause noise on

this unit, depending on the TV. Disconnect the LINE OUT

jacks in such cases.

•When playing DTS CDs in the DTS mode, noise may be

output at the begininng of playback.

•When playing/recording the DTS source through the

equipment connected to the LINE OUT jacks, cancel the

surround playback (See page 23).

AUX jacks

Accepts analog audio signal input from connected

equipment.

•When recording a VCD through this jack, track numbers

are not copied and one long track will be made.

Connect to the line output jacks of VCRs, LD players,

turntables, etc. with an optional audio connecting

cord with RCA phono plugs (red plug to R jack, white

plug to L jack).

•When a disc with 96 kHz sampling frequency rate is played

back, output from the DIGITAL OUT (OPTICAL) jack is

automatically converted to 48 kHz.

•By connecting the audio output of a VCR, you can play sound

tracks of Dolby Pro Logic videos through this system in

surround sound. See section "Dolby and DTS surround".

•When connecting a turntable, use one equipped with a built-

in equalizer amplifier.

DIGITAL OUT (OPTICAL) jack

Outputs digital audio signals to connected

equipment.

To select input to these jacks

Press AUX.

Connect to the optical input jacks of digital audio

equipment with an optional optical cord.

To change input level

1 Press AUX.

2 Press fDOWN or gUP repeatedly.

The input level changes from "MIN" to "6" and "MAX".

•Remove the dust cap a from the jack before connection.

Reattach the cap when the jack is not used.

•When the "OVER" level indicator lights up on the display,

the input level is too high. Turn down the input level.

Download from Www.Somanuals.com. All Manuals Search And Download.

CUSTOMIZING DVD SETUP

Ratings

Basic menu operation

Sets the rating limit of DVDs allowed to play back on this unit

when playing discs with restriction level encoding.

Basic operation of the SETUP MENU is described here.

Press DVD/CD and press SETUP while the player

is stopped.

The default “TV Aspect” setting has to be changed if you

are connecting to a 16:9 (wide) ratio TV set.

Any other setting can be changed or kept as is, according

to your preferences.

The “SETUP MENU” screen is displayed.

SETUP MENU

Choose The Item ik

On-screen Menu

Disc Languages

TV Aspect

4 : 3 LB

Level

Ratings

ENTER

Choose item

SETUP Completion

Press vV to move the cursor (the yellow-

highlighted area) to the setting to be changed.

Various TV/DVD settings can be changed as needed or preferred.

Press ENTER.

The menu screen for the item you selected will be

displayed.

•The language in which this menu is displayed can be

selected from three available languages (see “Menu

Language”, page 32). The menu in English is used here for

explanation.

Press vV to move the cursor to the desired

setting.

Overview of the Setup Menu

Press ENTER to enter your selection.

The selected setting is entered and the display returns to

the main setup screen of step 1.

For some settings, however, the screen will display a more

detailed menu. Follow the directions shown on the screen.

There are 4 major menu items that can be adjusted:

On-screen Menu

•Sets the on-screen guide display on or off.

•Selects a background color for the TV screen.

•Selects the language for this setup menu and the on-screen

guide messages.

Press SETUP to exit the setup menu.

To return to the previous screen

Press RETURN.

Disc Languages

Selects the preferred audio soundtrack language, subtitle

language, and menu language for DVD playback.

To exit the setup menu

Press SETUP.

TV Aspect

Sets the aspect ratio of the video signal sent to your connected

TV set.

Download from Www.Somanuals.com. All Manuals Search And Download.

To confirm your setting

1 Follow steps 1 to 4 above to display the setting you want to

confirm.

2 Press SETUP to exit the setup menu without making

changes.

Menu Language

Selects the language in which this setup menu and the on-

screen guide messages are displayed.

The default is “English”.

On-Screen menu

Set or select the on-screen guide display, background color for

the TV screen, and the language for this setup menu and the

on-screen guides.

On-screen Menu

Select “On-screen Menu” in the “SETUP MENU”

and press ENTER.

Choose The Item ik

•If you pressed RETURN or SETUP before pressing ENTER

to enter your selection, you return to the previous screen or

exit the setup menu, respectively, without entering your

selection. If you are uncertain of your present setup, follow

the steps above to confirm your setting.

•Your setting is not saved in the unit's memory until you

press POWER to turn off the power. If the unit suffers a power

interruption before it is turned off with POWER, setting will

revert to the previous one when the unit is turned on the

next time.

Guide Message

Background

Menu Language

O N

English

Select “Menu Language”and press ENTER.

Select the desired language and press ENTER.

ENTER

SETUP

Choose item

Completion

RETURN

Previous menu

Press RETURN to return to the previous screen

or press SETUP to exit the setup menu.

Guide Message

Sets whether or not to show the on-screen guide display at

the upper right corner of the TV screen.

The default is “ON”.

Disc Languages

•While the setup screen is displayed, you will not be able to

perform other operations on the DVD player. Press SETUP

again to exit the setup screen first.

Selects the preferred audio sound track language, subtitle

language and menu screen language for DVD playback.

Select “On-screen Menu” in the “SETUP MENU”

and press ENTER.

Disc Languages

Choose The Item ik

•Setup is canceled if the disc compartment is opened.

Audio Language

Subtitle Language

Disc Menu

Original

Auto

English

Select “Guide Message” and press ENTER.

Select the desired setting and press ENTER.

Press RETURN to return to the previous screen

or press SETUP to exit the setup menu.

ENTER

SETUP

Choose item

Completion

RETURN

Previous menu

Audio Language

The default is “Original”.

Background

Sets the background color of the TV screen while stopped.

The default is “Wallpaper”.

Select “Disc Languages” in the “SETUP MENU”

and press ENTER.

Select “On-screen Menu” in the “SETUP MENU”

and press ENTER.

Select “Audio language” and press ENTER.

Select “Background” and press ENTER.

Select the desired setting and press ENTER.

Press RETURN to return to the previous screen

or press SETUP to exit the setup menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

Select the desired language and press ENTER.

- “Original”: plays discs in the language specified as the

default on the disc. Go to step 5.

- “English”, “French”, “Spanish”: plays discs in the

selected language. Go to step 5.

- “Others”: language code screen appears to select any

other language. See step 4 of “Audio Language” setting.

TV Aspect

Sets the aspect ratio of the video signal sent to your connected

TV set.

Press RETURN to return to the previous screen

or press SETUP to exit the setup menu.

TV Aspect

Choose The Item ik

•If your preferred language does not exist on the disc, the

disc’s default language will be used.

- “Others”: language code setting screen appears to select

any other preferred language. Go to step 4.

NORMAL TV

WIDE TV

4 : 3

16 : 9

•To turn subtitles on or off, or to manually change the

displayed subtitle language, see “Changing subtitles”, page

21.

If “Others” is selected in step 3, enter a four-digit

language code with vV and numbered buttons,

and press ENTER.

Refer to the list of language codes on page 35.

To move the cursor, use Bb.

ENTER

SETUP

Choose item

Completion

RETURN

Previous menu

Disc Menu

The default is “English”.

The default is “4:3 LB (letterbox)”.

If you are connecting to a 16:9 (wide) ratio TV set, change the

setting to “Wide TV”.

Press RETURN to return to the previous screen

or press SETUP to exit the setup menu.

Select “Disc Languages” in the “SETUP MENU”

and press ENTER.

NORMAL TV

•If your preferred language does not exist on the disc, the

disc’s default language will be used.

•To manually change the audio tracks, see “Changing audio

tracks”, page 21.

Select “Disc Menu” and press ENTER.

Select “TV Aspect” in the “SETUP MENU” and

press ENTER.

Select the desired language and press ENTER.

- “English”, “French”, “Spanish”: shows the disc menu

in the selected language.

Select “NORMAL TV 4:3” and press ENTER.

Subtitle Language

The default is “Auto”.

Select the preferred setting when playing a disc

recorded in wide format, and press ENTER.

- “LETTER BOX”

The width of the picture is fit to the TV screen so that no

part of the picture is cut off.

- “Others”: language code screen appears to select any

other language.See step 4 of “Audio Language” setting.

Select “Disc Languages” in the “SETUP MENU”

and press ENTER.

Press RETURN to return to the previous screen

or press SETUP to exit the setup menu.

•If your preferred language does not exist on the disc, the

disc’s default language will be used.

•For the operation of the disc menu, see “Playing back with

the software specific menu”, page 16.

- “PAN & SCAN”

Select “Subtitle Language” and press ENTER.

The left and/or the right portions of each scene are cut

off as specified by the manufacturer, and the picture is

diplayed at full screen height.

Select the desired language and press ENTER.

- “Auto”: automatically displays subtitles in the language

specified in the "Audio Language" setting when needed;

ex) when the "Audio Language" is set to English, no

subtitles are displayed if current audio track is in English;

if the audio track is in any other language, English

subtitles are displayed.

Press SETUP to exit the setup menu.

•The preference setting for the 4:3 representation of wide

format software is only effective when playing a disc offering

such a choice. Such a disc may be labeled as "16:9 LB PS",

where LB stands for "Letter Box" and PS for "Pan & Scan".

Other discs, such as those labeled "16:9 LB" or "16:9 PS",

are played according to the disc's setting, regardless of your

preference.

- “English”, “French”, “Spanish”: shows subtitles in the

selected language.

Download from Www.Somanuals.com. All Manuals Search And Download.

Press ENTER.

WIDE TV

The password entry screen is displayed.

Select “TV Aspect” in the “SETUP MENU” and

press ENTER.

Use the numbered buttons and vV to enter a

four-digit password, and press ENTER.

Confirm your password.

Select “WIDE TV 16:9” and press ENTER.

Press SETUP to exit the setup menu.

Do not forget your password!

If you forgot your password, reset the DVD setup (see

“Resetting DVD setup”, page 38) and re-set all settings

again, including the “Ratings” setting.

Ratings

Sets the rating limit to play discs with restriction level encoding.

After confirming the password, press ENTER

again.

Rating Limit

Choose The Item ik

Level

(for Adult)

Press SETUP to exit the setup menu.

Changing the setting

(for Family)

Once the ratings settings have been set, you first need to enter

the password to change them.

ENTER

SETUP

Choose item

Completion

RETURN Previous menu

Select “Ratings” in the “SETUP MENU” and press

ENTER.

Setting the rating

The default is “Level 8”.

Input your four-digit password and press ENTER.

Select “Ratings” in the “SETUP MENU” and press

ENTER.

Select the setting to be changed and press

ENTER.

“Unlock Player” resets the rating level, country and

password setting to default.

Select your desired level and press ENTER.

The smaller the number, the higher the level of restriction.

For example, setting the rating level to 1 will restrict

playback of all discs with a rating level from 2 to 8, either

by cutting certain scenes or disabling playback altogether,

depending on the disc. Check your disc for details.

If you chose “Unlock player”, the message “The

player is unlocked” appears on the display. Press

ENTER.

For other settings, change to your desired setting

and press ENTER.

Select the country code for your country.

The country code needs to be set correctly, since the rating

system differs with the country.

Press RETURN to return to the previous screen

or press SETUP to exit the setup menu.

When “Other Country” is selected in the country code,

the display changes to accept 4-digit numbers. Input a 4-

digit country code shown on page 36 in the same way as

the input of the language code (page 33).

Download from Www.Somanuals.com. All Manuals Search And Download.

Use these numbers to specify the language in the “Disc Languages” setting (page 32).

LANGUAGE CODES

Code

Language

Code

Language

Code

Language

Code

Language

3738

3737

3742

5553

3749

3754

4461

3755

3760

3762

3837

4157

3850

4062

3844

3854

3843

4961

3841

4749

3937

6244

3951

4454

3955

4037

5048

4150

4151

4156

4251

Abkhazian

Afar

Afrikaans

Albanian

Amharic

Arabic

Armenian

Assamese

Aymara

Azerbaijani

Bashkir

Basque

Bengali; Bangla

Bhutani

Bihari

Breton

Bulgarian

Burmese

Byelorussian

Cambodian

Catalan

Chinese

Corsican

Croatian

Czech

4246

4845

4254

4261

4348

4737

4041

4148

4748

4350

4357

4437

4559

4445

4457

4555

4550

4537

4337

4556

4637

4659

4750

4755

4747

4761

4751

4757

4851

4837

4858

Fiji

Finnish

French

4850

4856

4947

4943

4955

4948

4956

4945

4954

4951

4950

5037

5041

5051

5154

5255

4237

5248

5256

5237

5357

5449

5451

5457

5549

5537

4340

5554

5544

5550

5540

Lingala

5545

5547

5548

5551

4155

5557

5559

5558

5648

5643

5637

5656

5641

5644

3851

5645

5651

5654

5647

5659

5747

5754

5762

5845

5851

3961

5951

6044

4645

6151

6257

Singhalese

Slovak

Slovenian

Somali

Spanish

Sundanese

Swahili

Swedish

Tagalog

Tajik

Lithuanian

Macedonian

Malagasy

Malay

Malayalam

Maltese

Maori

Marathi

Moldavian

Mongolian

Nauru

Nepali

Norwegian

Oriya

Pashto; Pushto

Persian

Polish

Portuguese

Punjabi

Quechua

Rhaeto-Romance

Romanian

Russian

Frisian

Galician

Georgian

German

Greek

Greenlandic

Guarani

Gujarati

Hausa

Tamil

Tatar

Hebrew

Hindi

Telugu

Thai

Tibetan

Tigrinya

Tonga

Turkish

Turkmen

Twi

Ukrainian

Urdu

Hungarian

Icelandic

Indonesian

Interlingua

Irish

Italian

Japanese

Javanese

Kannada

Kashmiri

Kazakh

Kirghiz

Korean

Kurdish

Laothian

Latin

Uzbek

Vietnamese

Volapük

Welsh

Wolof

Xhosa

Yiddish

Yoruba

Zulu

Samoan

Sanskrit

Scots Gaelic

Serbian

Serbo-Croatian

Shona

Danish

Dutch

English

Esperanto

Estonian

Faroese

Latvian; Lettish

Sindhi

Download from Www.Somanuals.com. All Manuals Search And Download.

Use these numbers to specify the country in the “Ratings” setting (page 34).

COUNTRY CODES

Code Country

BRUNEI DARUSSALAM

Code Country

6570

6576

6890

6583

6568

6579

6573

6581

6571

6582

6577

6587

6585

6584

6590

6683

6672

6668

6666

6689

6669

6690

6674

6677

6684

6679

6665

6687

6686

6682

7379

AFGHANISTAN

ALBANIA

ALGERIA

AMERICAN SAMOA

ANDORRA

ANGOLA

6678

6671

6670

6673

7572

6777

6765

6786

7589

6770

8468

6776

6778

6788

6767

6779

7577

6771

6775

6782

6773

7282

6785

6789

6790

6875

6874

6877

6879

8480

6967

6971

8386

7181

6982

6969

6984

7075

7079

7074

7073

7082

7088

7170

8070

8470

7165

7177

7169

6869

7172

7173

7182

7176

7168

7180

7185

7184

7178

7187

7189

7284

EGYPT

7277

7278

7275

7285

7383

7378

7368

7382

7381

7369

7376

7384

7477

7480

7479

7590

7569

7573

7580

7582

7587

7571

7665

7686

7666

7683

7682

7689

7673

7684

7685

HEARD ISLAND AND MCDONALD ISLANDS

BULGARIA

BURKINA FASO

BURUNDI

CAMBODIA

CAMEROON

CANADA

CAPE VERDE

CAYMAN ISLANDS

CENTRAL AFRICAN REPUBLIC

CHAD

CHILE

CHINA

CHRISTMAS ISLAND

COCOS (KEELING) ISLAND

COLOMBIA

COMOROS

CONGO

COOK ISLANDS

COSTA RICA

COTE D’IVOIRE

CROATIA

CUBA

CYPRUS

EL SALVADOR

EQUATORIAL GUINEA

ERITREA

ESTONIA

ETHIOPIA

FALKLAND ISLANDS (MALVINAS)

FAROE ISLANDS

FIJI

FINLAND

FRANCE

FRANCE, METROPOLITAN

FRENCH GUIANA

FRENCH POLYNESIA

FRENCH SOUTHERN TERRITORIES

GABON

GAMBIA

GEORGIA

GERMANY

GHANA

GIBRALTAR

GREECE

GREENLAND

GRENADA

GUADELOUPE

GUAM

GUATEMALA

GUINEA

GUNEA-BISSAU

GUYANA

HONDURAS

HONG KONG

HUNGARY

ICELAND

INDIA

INDONESIA

IRAN (ISLAMIC REPUBLIC OF)

IRAQ

IRELAND

ISRAEL

ITALY

JAMAICA

JAPAN

JORDAN

KAZAKHSTAN

KENYA

KIRIBATI

KOREA,DEMOCRATIC PEOPLE’S REPUBLIC OF

KOREA, REPUBLIC OF

KUWAIT

KYRGYZSTAN

LAO PEOPLE’S DEMOCRATIC REPUBLIC

LATVIA

ANGUILLA

ANTARCTICA

ANTIGUA AND BARBUDA

ARGENTINA

ARMENIA

ARUBA

AUSTRALIA

AUSTRIA

AZERBAIJAN

BAHAMAS

BAHRAIN

BANGLADESH

BARBADOS

BELARUS

BELGIUM

BELIZE

BENIN

BERMUDA

BHUTAN

BOLIVIA

BOSNIA AND HERZEGOVINA

BOTSWANA

BOUVET ISLAND

BRAZIL

CZECH REPUBLIC

DENMARK

DJIBOUTI

LEBANON

LESOTHO

LIBERIA

LIBYAN ARAB JAMAHIRIYA

LIECHTENSTEIN

LITHUANIA

DOMINICA

DOMINICAN REPUBLIC

EAST TIMOR

ECUADOR

BRITISH INDIAN OCEAN TERRITORY

HAITI

LUXEMBOURG

Download from Www.Somanuals.com. All Manuals Search And Download.

Code Country

SEYCHELLES

Code Country

7779

7771

7787

7789

7786

7776

7784

7772

7781

7782

7785

8984

7788

7077

7768

7767

7778

7783

7765

7790

7777

7865

7882

7880

7876

6578

7867

7890

7873

7869

7871

MACAU

MADAGASCAR

MALAWI

MALAYSIA

MALDIVES

7885

7870

7780

7879

7977

8075

8087

8065

8071

8089

8069

8072

8078

8076

8084

8082

8165

8269

8279

8285

8287

8372

7578

7667

8077

8667

8783

8377

8384

8365

8378

NIUE

8367

8376

8371

8375

8373

8366

8379

9065

7183

6983

7675

8368

8382

8374

8390

8369

6772

8389

8487

8474

8490

8472

8471

8475

8479

8484

8478

8482

8477

8467

8486

8571

8565

6569

7166

8583

8577

8589

8590

UGANDA

UKRAINE

NORFOLK ISLAND

NORTHERN MARIANA ISLANDS

NORWAY

OMAN

PAKISTAN

PALAU

PANAMA

PAPUA NEW GUINEA

PARAGUAY

PERU

PHILIPPINES

PITCAIRN

POLAND

PORTUGAL

PUERTO RICO

QATAR

REUNION

ROMANIA

RUSSIAN FEDERATION

RWANDA

SAINT HELENA

SAINT KITTS AND NEVIS

SAINT LUCIA

SAINT PIERRE AND MIQUELON

SAINT VINCENT AND THE GRENADINES

SAMOA

SAN MARINO

SAO TOME AND PRINCIPE

SAUDI ARABIA

SENEGAL

SIERRA LEONE

SINGAPORE

SLOVAKIA

SLOVENIA

SOLOMON ISLANDS

SOMALIA

SOUTH AFRICA

SOUTH GEORGIA AND THE SOUTH SANDWICH ISLANDS 8685

SPAIN

SRI LANKA

SUDAN

SURINAME

SVALBARD AND JAN MEYEN

SWAZILAND

SWEDEN

SWITZERLAND

SYRIAN ARAB REPUBLIC

TAIWAN, PROVINCE OF CHINA

TAJIKISTAN

TANZANIA, UNITED REPUBLIC OF 9087

THAILAND

UNITED ARAB EMIRATES

UNITED KINGDOM

UNITED STATES

UNITED STATES MINOR OUTLYING ISLANDS

URUGUAY

MALI

MALTA

MARSHALL ISLANDS

MARTINIQUE

MAURITANIA

MAURITIUS

MAYOTTE

UZBEKISTAN

VANUATU

8665

8669

8678

8671

8673

8770

6972

8969

8985

9082

9077

VATICAN CITY STATE (HOLY STATE)

VENEZUELA

VIET NAM

VIRGIN ISLANDS (BRITISH)

VIRGIN ISLANDS (U.S.)

WALLIS AND FUTUNA ISLANDS

WESTERN SAHARA

YEMEN

MEXICO

MICRONESIA (FEDERATED STATES OF)

MOLDOVA, REPUBLIC OF

MONACO

MONGOLIA

MONTSERRAT

MOROCCO

MOZAMBIQUE

MYANMAR

NAMIBIA

NAURU

NEPAL

NETHERLANDS

NETHERLANDS ANTILLES

NEW CALEDONIA

NEW ZEALAND

NICARAGUA

NIGER

YUGOSLAVIA

ZAIRE

ZAMBIA

ZIMBABWE

TOGO

TOKELAU

TONGA

TRINIDAD AND TOBAGO

TUNISIA

TURKEY

TURKMENISTAN

TURKS AND CACOS ISLANDS

TUVALU

NIGERIA

Download from Www.Somanuals.com. All Manuals Search And Download.

REFERENCE

•The picture quality may be poorer compared to normal

playback during pause, frame advance, fast forward or fast

reverse.

•Many DVD features, such as menu, subtitles, multi-audio,

multi-angle, and rating are dependent on the DVD software

itself. Check the instructions of your disc.

•If a multichannel source does not seem to be played with

the full surround effect, check the type of your source (page

22), selected audio track (page 21), and selected listening

mode (page 23 and 24).

Care and maintenance

Troubleshooting

Occasional care and maintenance of the unit and the software If your unit fails to perform properly, check the following guide

are needed to optimize the performance of your unit.

and the relevant sections of the Operating Instructions.

To clean the cabinet

There is no sound.

•Check speakers and AC power connection.

Use a soft and dry cloth. If the unit surfaces are extremely

dirty, use a soft cloth lightly moistened with mild detergent

solution. Do not use strong solvents such as alcohol, benzine

or thinner.

The unit shuts off suddenly.

•Possibly a short circuit in the speaker terminals. Disconnect

the AC power cord from the AC power outlet and re-connect

the speaker cords correctly.

Care of Discs

Resetting the unit

If the display window gets mangled, reset the unit as follows:

1 Press POWER to turn off the power.

If the power cannot be turned off, disconnect the AC power

cord, then plug it in again.

2 Hold down s and press POWER.

When a disc becomes dirty, wipe it from the center out with a

cleaning cloth. After playing a disc, store it in its case. Do not

keep it in hot or humid places.

The unit blacks out when the unit is turned off.

•Check your ECO mode setting.

Erroneous display.

•Reset the unit.

Poor radio reception.

Everything stored in memory after purchase is cleared.

•Check antenna connection. Adjust the antenna to find the

best reception.

•Move unit and antenna away from other electric appliances

and cords.

Resetting DVD setup

If trouble concerning DVD playback is not fixed with the

troubleshooting tips mentioned above, or if you want to reset

the DVD setup to default for any other reason, reset as follows:

1 Press DVD/CD.

The disc plays poorly (general).

•Check if the disc is correctly loaded.

2 Press s to stop disc playback.

•Check if the disc is not dirty.

•Check if the pickup lens is not affected by condensation. If

so, wait approximately one hour and try again.

3 Hold down ENTER and press s. Release when "CLEAR"

appears on the unit's display.

The power turns off automatically in a few seconds.

4 Press POWER to turn the power back on.

All your setup menu setting is cleared to default. All mark

data are erased.

The disc plays poorly (DVDs).

•Check that the disc's rating level does not exceed your

setting.

•Check that the disc is a NTSC color system disc.

• Check that the unit is not connected to a video deck, through

a selector switch, or to a TV set with a built-in video deck.

Picture noise may appear due to the DVD copy protection

scheme. Turn off the power or disconnect these equipment.

Download from Www.Somanuals.com. All Manuals Search And Download.

SUB WOOFER TS-LW700

FIVE SURROUND SPEAKERS SYSTEM SX-L700

(Front, surround and center speakers)

Specifications

Input

FROM CX-LDV700U: DIN 8-pin

FRONT: IMP. 8 ohms

MAIN UNIT CX-LDV700

TUNER

Output

Speaker system

Speaker units

Impedance

1 way (magnetic shielded*)

80 mm (3 ¹/4 in.) cone

Front: 8 ohms

CENTER: IMP. 8 ohms

SURROUND: IMP. 8 ohms

Front:

FM tuning range

FM usable sensitivity (IHF) 13.2 dBf

87.5 MHz to 108 MHz

Power output

Surround: 8 ohms

30 W + 30 W (40 Hz - 20 kHz, THD

less than 1 %, 8 ohms)

37 W + 37 W (1 kHz, THD 10 %, 8

ohms)

FM antenna terminals

AM tuning range

75 ohms (unbalanced)

Center: 8 ohms

530 kHz to 1710 kHz (10 kHz step)

531 kHz to 1602 kHz (9 kHz step)

350 µV/m

Dimensions (W x H x D)

100 x 220 x 115 mm

(4 x 8 ³/4 x 4 ⁵/8 in.) (with pedestal)

100 x 110 x 115 mm

(4 x 4 ³/8 x 4 ⁵/8 in.) (without

pedestal)

0.55 kg (1 lbs 3 oz)

Wall mounting screws (5)

Anti-skid patches (9)

AM usable sensitivity

AM antenna

Rear (Surround):

Loop antenna

30 W + 30 W (40 Hz - 20 kHz, THD

less than 1 %, 8 ohms)

37 W + 37 W (1 kHz, THD 10 %, 8

ohms)

DISC PLAYER

Laser

Weight

Accessories:

Semiconductor laser (DVD video

discs λ = 650 nm, CDs λ = 780 nm)

90 dB (1 kHz, 0 dB)

0.05 % (1 kHz, 0 dB)

NTSC color system

Signal-to-noise ratio

Harmonic distortion

Signal format

Center:

* The surround speakers are not magnetic shielded.

30 W (40 Hz - 20 kHz, THD less than

1 %, 8 ohms)

37 W (1 kHz, THD 10 %, 8 ohms)

Subwoofer:

55 W (40 Hz - 200 Hz, THD less than

1 %, 6 ohms)

68 W (60 Hz, THD 10 %, 6 ohms)

Bass reflex type, (Magnetic shielded)

160 mm (6 ³/8 in.)

Specifications and external appearance are subject to change

without notice.

S-VIDEO OUT (S1)

output:

Vp-p (75 ohms,

unbalanced)

C output: 0.286 Vp-p

Video composite output, 1 Vp-p (75

ohms, unbalanced), one RCA jack

5°C to 35°C (41°F to 95°F)

DOLBY DIGITAL/DOLBY PRO LOGIC

VIDEO OUT

Manufactured under license from Dolby Laboratories.

"Dolby", "Pro Logic" and the double-D symbol are trademarks

of Dobly Laboratories. Confidential unpublished works.

Operating conditions

Speaker type

Speaker unit

Frequency response

GENERAL

Input

Output

40 Hz - 200 Hz

AUX: 400 mV

DTS

TO TS-LW700U: Din 8-pin

LINE OUT: 300 mV, 1 kohm

DIGITAL OUT (OPTICAL)

PHONES: 32 ohms or more

120 V AC, 60 Hz

Manufactured under license from Digital Theater Systems, Inc.

US Pat. No. 5,451,942 and other worldwide patents issued

and pending. “DTS” and “DTS Digital Surround” are

trademarks of Digital Theater Systems, Inc. 1996 Digital

Power requirements

Power consumption

Dimensions (W x H x D)

120 V AC, 60 Hz

170 W

220 x 383 x 450 mm

(8 ³/4 x 15 ¹/8 x 17 ³/4 in.)

12 kg (26 lb. 7 oz)

Power requirements

Power consumption

Weight

25 W

Standby power consumption ECO ON: 0.7 W

ECO OFF: 9 W

Dimensions (W x H x D)

249 x 92 x 289 mm

(9 ⁷/8 x 3 ⁵/8 x 11 ¹/2 in.)

3.6 kg (7 lbs 15 oz)

Weight

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTE

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation.

This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on circuit different from

that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for

help.

CAUTION

Modifications or adjustments to this product, which are not

expressly approved by the manufacturer, may void the user’s

right or authority to operate this product.

For assistance and information

(United States and Puerto Rico)

Printed in Malaysia

Download from Www.Somanuals.com. All Manuals Search And Download.

3Com Network Card WL 601 User Manual
Acer Computer Monitor AL1715 User Manual
Alcatel Carrier Internetworking Solutions Telephone 4008 User Manual
Amana Dishwasher L0503010 User Manual
Amana Ice Maker D7824703 User Manual
American Audio Stereo Amplifier V1500 User Manual
American Standard Plumbing Product 211AA User Manual
Atlona Plumbing Product AT HD4 V41 User Manual
Baldor Computer Drive VS1MD User Manual
BC Speakers Speaker 15NW100 User Manual