Quick Installation Guide
5-Port 10/100 Mbps
Green Switch
Model# ASW305
Ver. 1A
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1
Hardware Description
Front Panel
LED Indicators
LED
Color
Status
Description
On
The switch is powered on.
The switch is powered off.
LAN port is connected.
POWER
Green
Off
On
LNK/ACT Green
Off
LAN port is not connected.
Transferring or receiving data.
Flashing
Rear Panel
Item Name
Power
Description
Power connector, DC 8V / 0.6A.
10/100 Mbps LAN ports 1 to 5.
1 - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
Connecting the Switch
Note: Operating Environment
This switch must be installed and operated within the limits of specified
operating temperature (32~1310F) and humidity (10~90%
Non-condensing). Do not place objects on top of the unit. Do not obstruct
any vents at the sides of the unit. Do not position the unit near any
heating source such as heater, radiator, or direct exposure to sun.
Prevent entering of water and moisture into the unit. If necessary, use
dehumidifier to reduce humidity.
Step 1 Connecting to network devices
The RJ-45 ports on the switch support Auto-MDI/MDI-X function which
allows using straight-through or cross-over type cables to connect this
switch to workstation or hub.
Connect one end of the network cable to the RJ-45 port on the rear panel,
and connect the other end of the network cable to the RJ-45 port on the
network device. Follow the same procedure to connect all the RJ-45 ports
of the switch. The UTP network cables must be two pairs Category 5 for
100Mbps data transmission; two pairs Category 3, 4 or 5 standards for
10Mbps data transmission. Maximum length, using UTP cable, between
the switch and connected device is 100 meters (300ft).
Step 2 Connecting the power
Connect the output end of the power adapter to the power connector on
the right panel of the switch. Connect the power adapter to the power
outlet. The green Power LED on the front panel should be lit. Once the
network cable is connected to both ends in Step 1 and the attached
network device is powered on, the green LNK/ACT LED should be lit.
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3
Troubleshooting
1. Power LED is not lit
•
Check if the power adapter is properly connected to the power outlet.
Make sure the power jack is firmly plugged into the power socket of
the switch.
2. Link/Activity is not lit when connect to 10/100 Mbps device
•
•
•
Check the power switch of the network device attached to the switch;
make sure it is turned ON.
Check the network cable; make sure it is properly connected to the
switch and the network device.
Check the network cable; make sure the UTP cables comply with the
specifications described in Section 2.
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4
Technical Support
E-mail: [email protected]
Website: www.airlink101.com
*Power savings may vary depending on products used. Actual data throughput will vary.
Network conditions and environmental factors lower actual data throughput rate.
Specifications are subject to change without notice. All rights reserved. Copyright © 2011
AirLink101®. AirLink101®, the stylized AirLink101® logo, specific product designations, and
all other words and logos that are identified as trademarks and/or service marks are, unless
noted otherwise, the trademarks and service marks of AirLink101®. All other product or
service names are the property of their respective holders. AirLink101® products are
protected under numerous U.S. and foreign patents and pending applications, mask work
rights, and copyrights.
Download from Www.Somanuals.com. All Manuals Search And Download.
|