Introduction
The ACE-615 is a very carefully engineered product designed to protect
your audio, video, and computer systems while providing them with clean
AC power. The surge protection is a nonsacrificial patented technology
(U.S. patents 4,870,534 and 4,870,528) that conforms to the strictest
Federal Guidelines for surge protection.
A C E - 6 1 5
A
C
E
-
6
1
5
AC enhancer
accessories
amplifiers
unswitched
b
c
d
e
fb
fa gb
ga
1@
circuit breaker
Surge Protector and AC Enhancer model ACE-615
voltage: 120V AC/60Hz, internal power consumption: 10w max
max 1500W
B
coax 1
coax 2
12v trigger
in
max 300W
accessories (switched 30 sec delay on turn-off)
out
in
out
in
unswitched
amplifiers (switched 10 sec delay on turn-on)
E
out
in
15A
GND
phone 1
phone 2
serial #
WARNING: For indoor use in dry locations only.
To reduce the risk of shock, do not expose this unit
to rain or moisture.
WARNING: Equipment with high-current requirements, such as hobby arc-welders, hair
dryers and heaters must not be plugged into these AC receptacles. Never allow total power
consumption of all equipment connected to these outlets to exceed 1800 watts.
10 Timber Lane
Marlboro, NJ 07746 USA
Made in the USA
power 120v 60Hz
max 1800W
hb
ib ia ha
1#
1$
j
1)
1!
owner’s manual
AC Enhancer
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Front Panel Control
indicating it is waiting for an external 12v trigger to power
on. Turn on the component supplying the 12v trigger. The
ACE-615 power button LED b and switched LED c and
amplifiers LED d will glow red indicating AC power is
being supplied to all connected components. Turn off
the 12v trigger supply to return the ACE-615 to
standby mode.
Press the ACE-615 power button b to activate the unit.
The power LED b, accessories LED c, and amplifiers
LED d will glow red. AC power is being supplied to all
connected components.
The unswitched front panel LED e indicates that AC
current is passing through the ACE-615 and into the
components connected to the unswitched AC rear
panel outlets 1). The unswitched LED e is always on
provided the unit is plugged into an active AC source.
To prevent turn-on thump, the jacks for the accessories
and amplifiers have seperate relays. When the ACE-615 is
turned on, the accessories power up before the amplifiers.
When powering down, the relay works in reverse. These
delays are in effect both with the 12V trigger source, and
without, and the duration may be adjusted by your autho-
rized ADCOM dealer.
Remote 12v Trigger Control
* Note: This section only applies when an external trigger is
connected to the 12v trigger in jack 1@.
* Note: The unit only responds to an external trigger when the
power button b is pressed in. The power button b can
be used to override the 12v trigger input and turn the
ACE-615 off.
Press the ACE-615 power button b to put the unit
into standby mode. The power LED b will glow amber
Typical Connections
to device
from wall
circuit breaker
Surge Protector and AC Enhancer model ACE-615
voltage: 120V AC/60Hz, internal power consumption: 10w max
B
coax 1
coax 2
12v trigger
in
max 300W
max 1500W
out
in
out
in
accessories (switched 30 sec delay on turn-off)
unswitched
amplifiers (switched 10 sec delay on turn-on)
out
in
15A
GND
phone 1
phone 2
serial #
WARNING: For indoor use in dry locations only.
To reduce the risk of shock, do not expose this unit
to rain or moisture.
WARNING: Equipment with high-current requirements, such as hobby arc-welders, hair
dryers and heaters must not be plugged into these AC receptacles. Never allow total power
consumption of all equipment connected to these outlets to exceed 1800 watts.
10 Timber Lane
Marlboro, NJ 07746 USA
Made in the USA
power 120v 60Hz
max 1800W
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble shooting
Symptom
Possible Causes
-Unswitched LED does not come on when the ACE-615 AC power cord is
plugged into an outlet
-Outlet may be shut off at the main breaker box
-Power button pushed in, but switched outlets are off and power LED glows
amber
-Unit may be in standby mode
-Remove any plug in the 12v trigger jack
-ACE-615 does not respond to 12v input
-Power button must be pressed in for remote activation
-The trigger voltage maybe outside the allowable + (5-12) volts
-
-No delay between accessories and amplifiers outlets
-Delay settings are incorrect. Return to authorized dealer for adjustment.
Factory settings are approximately ten seconds for amplifier turn-on and
thirty seconds for accessories turn-off.
Servicing
Technical Specifications
ADCOM has a technical service department to answer
questions pertaining to the installation and operation of your
unit. In the event of difficulty, please contact us for prompt
advice. If your problem can not be resolved through our
combined efforts, we may refer you to an authorized repair
agency, or authorize return of the unit to the factory. To aid us
in directing you to a convenient service station, please
indicate which major city is accessible to your home.
Electrical
Input power..........................................120VAC, +/-10%, 5-/60Hz
Protection.......................................................15A Circuit Breaker
Internal Power Consumption.........................Less than 5 watts
Control Input..................................................+/-5V to 24V AC/DC
Total Output................................................................................15A
Environmental: OperatingTemperature...............0 to +50 C
StorageTemperature...............-40 to +80 C
Filter
Phone or Fax inquiries to:
Phone (732) 683-2356
Fax (732) 683-9790
Mon - Fri 9AM - 5PM EST
Noise: Normal Mode................-5dB at 5kHz; -38 dB at 300kHz
Common Mode........-3dB at 300kHz; -40 dB at 1 MHz
Surge Protection
Endurance................................................1,000 surges 6 kV; 3 kA
Clamping.............................................................................172 volts
ResponseTime........................................................................0 sec.
(Passive protection / always on)
Maximum Applied Pulse (CombinationWave):
• Voltage: 6,000 volts
Please direct inquiries to:
ADCOM Service Department
Please include a return phone or fax number for the reply.
email and website info:
Please include a return e-mail address for the reply.
• Current: Unlimited due to current limiting
• Joules: Unlimited due to current limiting
Please address all mail inquires to:
ADCOM Service Corporation
10 Timber Lane
Marlboro, NJ 07746 USA
Please include a return address for the reply.
Mechanical
Dimensions....17”(430mm) x 12” (305mm) x 3.5”(89mm)
Weight..........................................................................10 lbs. (2.7 kg)
AC Cord............................................................................6 ft. (1.8m)
Download from Www.Somanuals.com. All Manuals Search And Download.
|