|
FPC-8057
5.7” STN LCD, Xscale-based touch screen
computer
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
ESD Precautions
Integrated circuits on computer boards are sensitive to static electricity. To
avoid damaging chips from electrostatic discharge, observe the following
precautions:
•
Do not remove boards or integrated circuits from their anti-static
packaging until you are ready to install them.
•
Before handling a board or integrated circuit, touch an unpainted
portion of the system unit chassis for a few seconds. This helps to
discharge any static electricity on your body.
•
Wear a wrist-grounding strap, available from most electronic component
stores, when handling boards and components.
Trademarks Acknowledgments
Acnodes Corp is a trademark of Acnodes Co., Ltd.
IBM is a registered trademark of International Business
Machines Corporation.
MS-DOS, Microsoft C and QuickBasic are trademarks of
Microsoft Corporation.
TURBO C is a trademark of Borland Inc. BASIC is
a trademark of Dartmouth College. Intel is a
trademark of Intel Corporation.
Other brand names and trademarks are the properties
and registered brands of their respective owners.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
The FPC-8057 is packed in an anti-static bag. The product has components that
are easily damaged by static electricity. Do not remove the anti-static wrapping until
proper precautions have been taken. Safety instructions in front of this User’s
Manual describe anti-static precautions and procedures.
After unpacking the product, place it on a raised surface and carefully inspect the
board for any damage that might have occurred during shipment. Ground the
product and exercise extreme care to prevent damage to the product from static
electricity.
Integrated circuits will sometimes come out of their sockets during shipment. The
FPC-8057 5.7” STN LCD, Xscale-based touch screen computer package
includes the following:
•
FPC-8057 * 1
•
•
•
•
•
Driver CD *1
USB sync. cable *1
Touch pen * 1
Fuse * 1
Panel mount * 2
Make sure that all of the items listed above are present.
What To Do If There Is A Problem
If there are damaged or missing parts, contact your supplier and/or dealer
immediately. Do not attempt to apply power to the product if there is damage to any
of its components.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
Overview
This section states the safety instructions, which must be followed when installing,
operating and servicing the FPC-8057. If neglected, physical injury and death may
follow, or damage may occur to controller and related equipment. The material in
this chapter must be studied before attempting any work on, or with, the unit.
Warnings and Notes
This manual distinguishes safety instructions. Warnings are used to inform of
conditions, which can, if proper steps are not taken, lead to a serious fault
condition, physical injury or death. Notes are used when the reader is required to
pay special attention or when there is additional information available on the
subject. Notes are less crucial than warnings, but should not be disregarded.
Readers are informed of situations that can result in serious
physical injury and/or serious damage to equipment with the
symbol shown to the left. A Warning symbol indicates that the
reader should pay special attention to the accompanying text.
Precautionary steps should be taken to insure that the
installation is in compliance with warnings. Warnings include
Warnings
Warnings
hazardous conditions that could cause personal injury or
equipment damage if care is not taken. The text next to this
symbol describes ways to avoid the danger.
Dangerous Voltage Warnings: Warns of situations in
which high voltage can cause physical injury and or
v
Download from Www.Somanuals.com. All Manuals Search And Download.
damage equipment.
General warning: Warns of situations, which can cause
physical injury and or damage equipment by means other than
electrical.
Electrostatic Discharge Warning: Warns of situations in
which an electrostatic discharge can damage equipment.
Readers are notified of the need for special attention or additional in formation
available on the subject with the following symbols:
CAUTION!
Aims to draw special attention to it.
Note:
Note: gives additional information or points out more
information available on the subject.
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Disclaimers --------------------------------------------------------ii
ESD Precautions --------------------------------------------------iii
Unpacking ---------------------------------------------------------iv
Safety Instructions ------------------------------------------------ v
Chapter 1 Introduction-------------------------------------------- 1
1.1 General Description .........................................................1
1.2 Features ...........................................................................2
1.3 Specifications ...................................................................2
Chapter 2 Installation Instructions---------------------------- 5
2.1 Mounting Instructions .....................................................5
2.1.1 Location Considerations ......................................... 5
2.1.2 Making a NEMA-4 Mounting .................................. 5
2.1.3 Environmental Considerations .............................. 7
2.2 Power Connections ............................................................ 8
2.2.1 Power Requirements......................................................9
2.2.2 Grounding Requirements ..........................................11
2.2.3 CE Requirements ........................................................ 12
2.2.4 Safety Guidelines......................................................... 12
2.3 Communications Connections ..................................... 14
2.3.1 COM 1 [RS-232] ........................................................14
2.3.2 COM2 [RS-232] & COM3 [RS-422/485] ................16
2.3.3 Dip Switch ..................................................................17
Table of Contents
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4 CE Requirements ..........................................................18
2.5 Dimensions of FPC-8057 .............................................19
Chapter 3 Windows CE.NET ------------------------------ 21
3.1
Introduction ...............................................................21
3.2
Utilities .......................................................................22
3.2.1 Soft-Keyboard ......................................................... 22
3.2.2 System Settings ....................................................... 23
3.2.3 IPSM ............................................................................ 26
3.2.4 Startup........................................................................ 27
3.2.5 Remote Desktop Connection (Windows XP
only) ....................................................................... 28
3.3 FPC-8057 Networking ..................................................31
3.3.1 Networking via Ethernet ....................................... 31
3.3.2 Networking via USB Client Port ........................... 32
3.3.3 Web browser ........................................................... 34
3.4 Application program development ...............................35
3.4.1 Microsoft eMbedded Visual C++ 4.0 ................ 35
3.4.2 FPC-8057 SDK............................................................ 37
Appendix A Example --------------------------------------- 39
Appendix B How to Update WindowsCE image ------- 41
Appendix C How to use development tools-eMbedded
C++4.0--- 43
Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
Chapter 1
Introduction
1.1 General Description
The FPC-8057 series are fan-less and compact-size touch panel
computers. It equips with 5.7” STN LCD display, Windows CE.NET and
low power consumption CPU, Intel Xscale PXA255. Therefore, FPC-
8057 series are good cost-effective choices for operator interface
applications.
The FPC-8057 adopts most reliable and stable design. With fan-less CPU
and CompactFlash card, FPC-8057 is especially suitable for vibration
environment such as transportation, semiconductor etc. In addition, FPC-
8057 is also bundled with Windows CE.NET, which forms a bridge that lets
FPC-8057 be an open HMI solution for system integration. For connecting
other devices, the FPC-8057 also provides several interfaces: RS-
232/422/485, Ethernet etc.
Introduction
1
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
1.2 Features
z Fan-less and low power consumption CPU- Xscale PXA255 z
5.7” QVGA color STN LCD
z Windows CE.NET supported and flash ROM on-board z
Slim and compact size design
z Suitable for reliable and vibration application – Fan less and
CompactFlash card
z NEMA 4 / IP65 compliant front panel z
Support Compact Framework
z Over-voltage power protection – fuse
1.3 Specifications
z Construction: plastic molding housing
z Display: 5.7" QVGA Color STN LCD
z CPU and core logic: Intel™ Xscale PXA255 z
Flash ROM/SDRAM on board
32 MB Flash ROM / 64MB SDRAM z
1 CompactFlash™ card slot z I/O: 2
serial ports
COM1: RS-232, COM2: RS-232/422/485 z
1 Ethernet port (10Base-T) z 2 USB host ports
z 1 USB client for ActiveSync
z Sound output: 16 bit sound output z
RTC: Dallas DS1685
z Power input: 24 VDC, 0.5A maximum
z Dimension (W x H x D): 204 x 150 x 48mm z
Weight: 1.0kg
Introduction
2
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
LCD Display
z Display type: STN color LCD
z Display size (diagonal): 5.7" z
Max colors: 4096 z Resolution:
320 x 240
z Pixel pitch (HxV, mm): 0.36 x 0.36 z
Viewing angle: 100° z Luminance
(cd/m2): 150 z Storage temperature: -
20~60°C z Operating temperature:
0~45°C z Backlight: CCFL z Contrast
ratio 30:1
Touch screen
z Type: 4-wire, analog resistive
z Resolution: 320*240
z Light transmission: above 80% z
Life: 1 million activation minimal
Fuse
z BUSSMANN
z Fast Acting, Glass Tube z
Rating: 250VAC, 1A z Size:
5x20mm
Environmental Specifications
z Operating temperature: 0° ~ 45°C (32° ~ 113°F)
z Relative humidity: 10% ~ 90% @ 40°C, non-condensing z
Shock (operation): 10 to 25Hz(X,Y,Z direction 2G
30minutes) z
EMI: Complies FCC class A
Introduction
3
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
z CE: Complies with EN50081-2 and EN50082-2 standards z
Front panel meets NEMA4 / IP65
Introduction
4
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
Chapter 2
Installation Instructions
2.1 Mounting Instructions
2.1.1 Location Considerations
Care should be taken when locating equipment behind the unit to ensure
that AC power wiring, PLC output modules, contactors, starters and relays,
and any other source of electrical interference are located away from the
back of the unit.
Particular note should be taken to the position of variable speed drives and
switching power supplies. Their input and load cables should be screened
to a central star earth point.
2.1.2 Making a NEMA-4 Mounting
The unit can be mounted into panels with a depth of
4”(105mm). It is recommended that the unit be mounted
Panel Details on the front panel of a steel enclosure, through an
appropriate opening*. Allow a clearance of 1”(25mm)
around the sides of the unit for mounting hardware. Allow
clearance for cable connections to the back of the unit. Unit
depth may vary according to cable type used. Typically,
plan a depth to accommodate at least 4”(105mm) behind
the panel.
Put the unit through the panel cut out. Slide the clamps
into the 6 holes provided around the case. Tighten the
clamping screws in an even pattern until
NEMA-4
Mounting
Installation Instructions
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
the unit is secured in the panel. Caution!
Do not over tighten mounting clamps!
Specifications Note:
Note:
To seal to NEMA-4 specifications, all supplied mounting
clamps must be used and panel cannot flex more than
0.010”.
Installation Instructions 6
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
2.1.3 Environmental Considerations
z The FPC-8057 are to be used indoors as built in displays. Make sure
that the displays are installed correctly and that the operating limits are
followed (See Specifications).
z
Do not operate the unit in areas subject to explosion hazards due to
flammable gases, vapors or dusts.
z The unit should not be installed where fast temperature variations and/or
high humidity are present. This will cause condensation of water in
the device.
z
Do not install these terminals in environments where have
inflammable gases.
Installation Instructions
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
2.2 Power Connections
Make sure that all local and national electrical standards are met when the
installing the unit. Contact your local authorities to determine which codes
apply.
Installation Instructions 8
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
2.2.1 Power Requirements
The FPC-8057 can be powered by DC power only. The
specified voltage range is +21 to 25 Volts DC. This
insures compatibility with most controller DC systems. The
power conditioning circuitry inside the unit is accomplished
by a switching power supply. The peak starting current can
be as high as 700mA.
Power
If the display does not come on within 2 seconds of
power up, remove power. An internal fuse will prevent
damage if the polarity of the DC power is incorrect. Check
wiring to insure proper connections and try to power up
again.
Fusing
Requirements
An Internal fuse will prevent damage for over voltage
condition however it isn’t guaranteed.
DC voltage sources should provide proper isolation from
main AC power and similar hazards.
Caution
High Voltage
A Hard-wired EMERGENCY STOP should be fitted in
any system using a FPC-8057 to comply with ICS
Safety Recommendations.
Do not power the FPC-8057 and inductive DC loads, or
input circuitry to the controller, with the same power
supply. Note: The 24 VDC output from some controllers
may not have enough current to power the FPC-8057
Caution
Emergency
Stop
Wire lengths should be minimized (Maximum 1600’ (500
m) shielded, 1000’ (300 m) unshielded).
Caution
Supply Voltage
Wires should be run in pairs with a neutral or
Condition
Caution
Wire Routing
Installation Instructions
9
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
common paired with a hot or signal line.
If wiring is to be exposed to lightning or surges, use
appropriate surge suppression devices.
Keep AC, high energy, and rapidly switching DC
wiring separate from signal wires.
Equip ungrounded DC supplies with a resistor and
capacitor in parallel to earth ground. This provides a path
for static and high frequency dissipation. Typical values to
use are 1MOhm and 4700pF.
To make a connection, strip about 3/8” of insulation off the
end of the wire, turn the connector screw
counterclockwise until the gap is wide open, insert the
wire all the way in, and turn the screw clockwise until it’s
tight.
Connection
Connect positive DC line to the ‘+24V’ terminal and the
DC ground to the ‘0V‘ terminal.
10
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
FUSE Replacement:
The fuse use on FPC-8057 is:
BUSSMANN
Fast Acting, Glass Tube
Rating: 250VAC, 1A Size:
5x20mm
Warning:
Make sure the power off before replace the fuse. Do
1.
2.
not replace the fuse with a different rating fuse.
2.2.2 Grounding
Requirements
Chassis ground must be used. DC ground is not directly coupled to Earth
ground internally. It is preferable not to ground DC negative return to
chassis ground as poor site earths can introduce noise into a system, but if
necessary an earth connection should be made, from the power supply
return point to the central star earth point. Ground conductors should be as
short and as large in size as possible. The conductors must always be
large enough to carry the maximum short circuit current of the path being
considered. Ground conductors should be connected to a tree from a
central star earth ground point. This ensures that no ground conductor
carries current from any other branch.
Installation Instructions
11
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
2.2.3 CE Requirements
To make a FPC-8057 comply with EMC directives, and to reduce
susceptibility to electrical interference, a separate #14 AWG ground wire
should be taken to the chassis ground terminal of the power connector. This
ground connection should be run directly to the central star earth
connection point (as recommended in most Installation Instructions).
2.2.4 Safety Guidelines
This section presents recommended installation practices, and
procedures. Since no two applications are identical, these
recommendations should be considered as guidelines.
Hardware Considerations WARNING!
The system designer should be aware that devices in Controller systems
could fail and thereby create an unsafe condition. Furthermore, electrical
interference in an operator interface, such as a FPC-8057 can lead to
equipment start-up, which could result in property damage and/or physical
injury to the equipment operator.
If you, or your company, use any programmable control systems that
require an operator or attendant, you should be aware that this potential
safety hazard exists and take appropriate precautions. Although the specific
design steps depend on your particular application, the following
precautions generally apply to installation of solid-state programmable
control devices. In addition, these precautions conform to the guidelines for
installation of Controllers as recommended in the NEMA ICS 3-304 Control
Standards.
12
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
Programming Considerations
To conform to ICS Safety Recommendations, checks should be placed in the
controller to ensure that all writable registers that control critical parts of
plant or machinery have limit checks built into the program, with an out-of-
limit safe shut down procedure to ensure safety of personnel.
ICS 3-304.81 Safety Recommendations:
Consideration should be given to the use of an emergency stop
function, which is independent of the programmable controller.
Where the operator is exposed to the machinery, such as in loading or
unloading a machine tool, or where the machine cycles automatically,
consideration should be given to the use of an electromechanical override
or other redundant means, independent of the programmable controller, for
starting and interrupting the cycle.
If provision is required for changing programs while the equipment is in
operation, consideration should be given to the use of locks or other
means of assuring that only authorized personnel can make such
changes.
These recommendations are intended as safeguards against the failure of
critical components and the effects of such failures or the inadvertent
errors that might be introduced if programs are changed while the
equipment is in operation. *
z The ICS 3-304.81 Safety Recommendations are reproduced by
permission of the National Electrical Manufacturers Association from
NEMA ICS 3-304
Installation Instructions
13
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
2.3 Communications Connections
There are several ports in the back of the case. Please take the
following information for reference.
2.3.1 COM 1 [RS-232]
Different cables are required for
various devices.
Cable
Restrict cable length to less than 50’
(15m) for RS-232 devices to avoid
communications problems.
Requirements
Caution
Shielded cable must be used for long
lengths or cables run in an electrically
noisy environment.
Do not run cables next to AC power
lines or near sources of electrical noise.
Be sure that the cable ends have been
inserted all of the way into mating
connectors and are secure
14
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
Pin assignment of the 9 Pin, Female,
SUB-D, COM1 [RS-232] Port.
Pin Designations
Note: This port is not used for
downloading or for printing functions.
COM1 [RS-232]
Pin# Symbol Function
1
2
3
4
5
6
7
DCD
RxD
TxD
Data Carrier Detect
Received Data
Transmitted Data
Data Terminal Ready
Signal Ground
DTR
GND
DSR
RTS
Data Set Ready
Ready to send
output
8
9
CTS
RI
Clear to send input
Ring Indicator
Installation Instructions
15
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
2.3.2 COM2 [RS-232] & COM3 [RS-422/485]
The 9 Pin, male, SUB-D, COM2 [RS-232] & COM3 [RS-422/485] Port
on the back of the unit is the downloading port (PC Connector) and RS-
485/422 communications port for connecting to a device.
Connector COM2 [RS-232] & COM3 [RS-2422/485]
Pin Designations
COM2
COM3
COM3
Pin# Symbol
(RS-232)
(RS-422)
(RS-485)
GND
GND
GND
1
2
3
4
5
6
7
8
9
GND
Tx+
RS-422 Transmit
RS-422 Transmit
RS-422 Receive
RS-422 Receive
Tx-
Data+
Data
Rx+
Rx-
GND
RxD
TxD
Receive
Transmit
Not used
16
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
2.3.3 Dip Switch
Pin1 Pin2 Mode
OFF OFF Normal
ON
OFF Touch Screen Calibrate mode
OFF ON Boot Loader mode
Pin3, 4 unused
z Touch Screen Calibrate mode: In this mode when you power on the
FPC-8057, the screen will display a “+” sign at the center of the
screen. Use a stylus or finger to push the center of the “+” until it
moves. The “+” moves to upper-left, lower-left, lower-right and upper-
right corners. When all five “+” are done the “+” will disappear. The
Touch Screen parameter will store at Flash Rom.
Installation Instructions
17
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
z Boot Loader mode: Load new Windows CE.NET image file. If the FPC-
8057 already load the CE image with boot loader. Set the DIP SW2
ON then power ON into boot loader mode. Refer the load Win CE
image document.
2.4 CE Requirements
EU directives that apply to the FPC-8057 Series:
z EMC Directive (89/336/EEC, 92/31/EEC, 93/68/EEC)
electromagnetic emissions and immunity
z Machinery Directive (89/392/EEC, 91/368/EEC, 93/44/EEC, 93/
68/EEC) machine safety
The FPC-8057 Series has been designed to operate satisfactorily in
electromagnetic noise (immunity) and without emitting high levels of electrical
noise into the environment (emission). The units are designed to meet
European Community standards when installed per the wiring instructions in
this manual.
Compatibility
Standards
The FPC-8057 has been designed to meet
electromagnetic compatibility for industrial
environments.
• CISPR (EN 55011) Group 1, Class A Radiated
Emissions levels
• EN50081-2 Generic emission standard,
industrial environment (Also US FCC Class A)
• EN50082-2 Generic immunity standard,
industrial environment
18
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
2.5 Dimensions of FPC-8057
Installation Instructions
19
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
20
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
Chapter 3
Windows CE.NET
3.1 Introduction
The FPC-8057 series operator interface terminal is designed to serve on the
Windows CE.NET platform. Designed from the ground up for the
embedded marketplace, Windows CE.NET delivers a robust real-time
operating system for rapidly building the next generation of smart mobile and
small footprint devices. With a complete operating system feature set and
end-to-end development environment, Windows CE.NET contains
everything you need to create a custom Windows CE.NET–based device
that requires rich networking, hard real-time, and a small footprint, as well
as rich multimedia and Web browsing capabilities.
Windows CE.NET
21
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
3.2 Utilities
There are several useful utilities built in the standard Windows CE.NET
OS of FPC-8057:
3.2.1 Soft-Keyboard
The FPC-8057 is dedicated to the small-sized operator interface. It is often
inconvenient for users to attach a keyboard to such small machine. Thus,
a software keyboard is embedded in the standard Windows CE.NET OS.
Upon boot-up, a small keyboard icon will appear on the status bar. Tap
this icon by the stylus to activate/hide this Soft-keyboard.
22
Windows CE.NET
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
3.2.2 System Settings
FPC-8057 provides an integrated utility for users to make basic setting of
the machine.
Windows CE.NET
23
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
disappear. The Touch
Screen parameter will
store at Flash Rom.
Backlight
“LCD Settings” page of the cecp provides the function to turn off the LCD
backlight, and thus elongates the period of service. For example, if the user
wants the backlight turned off automatically after 10 minutes when the device
was no longer used. The user must select “10 minutes” in the put down
box and then press “OK” button. Then the screen save function is
enabled. Once the backlight was turned off, events or perturbations from
the touch screen can turn it on.
On the other hand, if users want to disable the screen save function,
select “Never” and press “OK” button.
Windows CE.NET
25
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
MAC address
The MAC address p
age the block shows the
network MAC address. S ave
T ap the Save registry
button, would save the reg istry data to the IPSM folder. Next time reboot
the
FPC-8057, Window s CE.NET system will use the stored registry data.
26
Windows CE.NET
Download from Www.Somanuals.com. All Manuals Search And Download.
Or in FPC-8057 \Windows folder click the “backupreg.exe” and it will
save the registry data too.
IPSM(Intel Persisten t Storage Manager)
The IPSM serves as a small capacity hard disk. You can store your dat a
and application in the Flash ROM via IPSM function to prevent nexpected
loss of data as power failure. Whe
u
n power is
shutdown and cold boot, the data in the Flash ROM area would be
saved.
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
3.2.4 Startup
After the system boot up, the startup execution function would
a utomatically perform. This function is useful for control system to do the
initialization p rocesses or some other programs.
Step1: Create "startup" directory in in "\IPSM\".
Step2: Copy executable files or Shortcut to "StartUp" directory,
which is created in Step 1.
An
py
alternative way to setup startup files is to make a shortcut and co it to
"IPSM
ecute a program with
\StartUp". A shortcut can ex P
arameters.
Follow the following procedure to create the shortcut (.lnk) file.
Windows CE.NET
27
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
A .lnk file is a text file that contains the command line for the linke d target,
which may be enclosed in double quotation marks, along with the length of
that command line. Optionally, you can also pass parameters into the
linked target. By default, a .lnk file uses the following format.
[number of ASCII characters after pound sign]#[command line]
[optional parameters]
For example, to start M yApp.exe and pass two optional parameters into
the application, a sample MyApp.lnk file contains the following.
40#\Windows\MyApp.exe parameter1 parameter2
3.2.5 Remote Desktop Connection (Window s XP only)
Use Remote Desktop Connection you can remotely control your
computer.
To use Remote Desktop, you need the following:
Windows XP installed on your office computer, or
Professional inst
whichever computer you plan to operate remotely. This
computer is known as the host.
You must first enable the Remote Desktop feature on your office computer
so that you can control it remotely from another computer. You must be
logged on as an administrator or a member of the Administrators group to
enable Remote Desktop on your Windows XP Professional-based
computer.
28
Windows CE.NET
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
To create a new Remote Desktop Connection 1.
Open Remote Desktop Connection.
2. In Computer, type the computer nam e for your computer running Windows
XP Professional that has Remote Desktop enabled and for which you
have Remote Desktop permissions.
Windows CE.NET
29
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
3.
appears.
Click Connect. The Log On to Windows dialog box
4. In the Log On to Windows dialog box, type your user name, password,
and domain (if required), and then click OK. The Remote Desktop
window will open and you will see the desk top settings, files, and
programs that are on your office computer. Your office computer will
remain locked. Nobody will be able to work at your office computer without
a password, nor will anyone see the work you are doing on your office
computer remotely.
Note: To change your connection settings, (such as screen size,
automatic logon information, and performance options), click Option s
before you connect.
30
Windows CE.NET
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
3.3 FPC-8057 Networking
3.3.1 Networking via Ethernet
The FPC-8057 is equipped with a 10Base-T Ethernet controller. To utilize it,
change the device name when the FPC-8057 is first turned on.
Step
1 Click
“Start/Settings/Control
___ Panel” _____________________________________________
2 Double click “Network and Dial-up Connections”
3 Find the default device name.
Change it to a unique one
depending on
the plan of individual LANs. ____ LAN90001 _______________________
4 If the FPC-8057 is a nod e of a
LAN with DHCP servers, it is
now available.
5 If the FPC-8057 is a nod e
___ of a LAN with fixed IP
Windows CE.NET
31
Download from Www.Somanuals.com. All Manuals Search And Download.
server, please consult with
MIS to get specific IP address.
Click “Start/Settings/Control
Panel”. Double click “Network
and Dial-up Connections” and
update
___ the IP address. _______________________________________
6 Use the cecp utility “Save
registry” to save this
changed.
The FPC-8057 can use the USB client to USB host cable connect the
USB client port of the FPC-8057 and the USB host port of the host
computer as following:
Step
Make sure the
1
Microsoft ActiveSync
service is properly
installed on the host
PC.
Microsoft
ActiveSync
Power ON the
2
FPC-8057.
Before the Windows
CE.NET boot up, don’t
connect the USB
cable.
Windows CE.NET
32
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
3 Connect the USB client
port of the FPC-8057
and the USB host port
of the host PC by the
USB client to USB host
___cable. _______________________________________________
4 When the “Add New
Hardware Wizard”
asks for the driver,
select the file
D:\FPC-8057\USBdri
__ ver\ wceusbsh.inf _____________________________________
5 Follow the onscreen
instructions to establish a
partnership and
synchronize your FPC-
8057with your desktop
computer.
6 Now you can
synchronize the
information between
the FPC-8057 and host
computer with
ActiveSync.
Windows CE.NET
33
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
3.3.3 Web browser
The FPC-8057 built-in Windows CE.NET OS includes Microsoft IE sample. It
can be used to browse web pages on World Wide Web via LAN or dial-up
connection.
Windows CE.NET
34
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
3.4 Application program development
The FPC-8057 is bundled with built-in Windows CE.NET operating
system and with Compact Framewrok. In real applications users need to
execute various applications programs on it. However, unlike its other
family the Windows CE.NET is a hardware-dependent operating system. That
is to say, Windows CE.NET application programs are only portable in the
source code level. Users must rebuild the runtime file for a different
Windows CE.NET platform even though the source code may not be
changed at all.
To develop your application program, you can use two development
tools. Visual Studio.NET or eMbedded Visual C++ 4.0.
For Visual Studio.NET, you can download newest version of Compact
Framework from Microsoft website.
For eMbedded Visual C++4.0; the following development tools must be
installed on the PC:
z Microsoft eMbedded Visual C++ 4.0
z Microsoft eMbedded Visual C++ 4.0 Service Pack 1 z FPC-
8057 SDK
3.4.1 Microsoft eMbedded Visual C++ 4.0 System
Requirements
To use Microsoft eMbedded Visual C++ 4.0 you need the following:
z A desktop computer with a Pentium-II class processor, 450 MHz or
faster
Windows CE.NET
35
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
z Microsoft Windows® 2000 Professional SP2, Microsoft Window
2000 Server SP2, or Microsoft Windows XP Professional.
z 96 MB (128 MB recommended) memory for Windows 2000
Professional or Windows XP Professional. 192 MB (256 MB
recommended) memory for Windows 2000 Server.
z CD-ROM drive required
z VGA or higher-resolution monitor. A Super VGA (800 x 600 or larger)
monitor is recommended.
z
Mouse or compatible pointing device. z
200 MB hard disk space.
36
Windows CE.NET
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
3.4.2 FPC-8057 SDK
The FPC-8057 SDK provides developers with access to an extensive set of
functions that are specific to the FPC-8057 hardware.
Installing the FPC-8057 SDK
Step
Download or from
1.
FPC-8057 SDK CD
find the
FPC-8057_SDK.msi
file.
Double click the file’s
name start the Setup
Wizard.
The installer will be
2
prompted for
acceptance of a
license agreement.
Following that, the
SDK should install
itself automatically on
the host machine
without further
operator intervention.
Windows CE.NET
37
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
When installation is
3
complete the following
message should
appear: “Completing
the FPC-8057 Setup
Wizard”. The installer
must press the “Finish”
button in the install
window to exit.
38
Windows CE.NET
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
Appendix A
Example Program
The FPC-8057 offers loop back test program for two comports. Please
select the program D:\FPC-8057\Example\Serial Test.
Serial port loop back test program
Before running the program, you need to connect two comports of the
FPC8057.
COM2
(RS-232)
COM1 (RS-232)
RxD
7
8
TxD
Example Program
39
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
This page does not contain any information.
40
Example Program
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
Appendix B
How to Update WindowsCE image
If you want to update new WindowsCE image to FPC-8057, you can follow
the procedure.
1. Download newest version of WindowsCE image from
2. Save new WindowsCE image into CompactFlash card and
rename it to “nk.bin”.
3. Set the DIP switch as follows.
4. Power on the FPC-8057. Then, it updates FPC-8057 image and
automatic reboot and into Windows CE.
How to Update WindowsCE image
41
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
This page does not contain any information.
42
How to Update WindowsCE image
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
Appendix C
How to use development tools-
eMbedded C++4.0
The following procedure will show you how to use development
tools-eMbedded C++4.0.
1. Before you start to develop the application program, you need to install
following three S/W to Host PC.
(1) USB driver in the driver CD.
(2) eMbedded C++ 4.0
(3) Microsoft ActiveSync. software
(4) SDK (Software Development kit) in the driver CD.
How to use development tools
43
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
2. Plug synchronized cable which is in the package to the USB client port
of the FPC-8057.
3. Run Microsoft ActiveSync. software.
44
How to use development tools
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
4. Select “No”
5. Host PC synchronizes to FPC-8057. Click the item “Explore” and
fine all folders in the FPC-8057.
How to use development tools
45
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
6. If you plug the CompactFlash card in the FPC-8057. You can fine out the
folder “StorgeCard” in FPC-8057.
7. Run eMbedded VC++4.0 in host PC..
46
How to use development tools
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
8. Open a new project
How to use development tools
47
Download from Www.Somanuals.com. All Manuals Search And Download.
FPC-8057 User’s Manual
10. If you install FPC-8057’s SDK successfully, you can select FPC-8057 in
the item. Then, click “Run” to compile your application program
into “.exe” file.
11. The “.exe” file is being sent to the FPC-8057 sync. You can find it in
FPC-8057.
48
How to use development tools
Download from Www.Somanuals.com. All Manuals Search And Download.
|
ABC Office Trimmer 440 User Manual
Abocom Network Router FSW410 User Manual
Adcom Stereo Amplifier GFP 750 User Manual
Agilent Technologies Blood Glucose Meter AN 372 1 User Manual
Air King Ventilation Hood SEV24SSH User Manual
Alesis Stereo Equalizer DEQ230 User Manual
Alpha ToolComHK Limited Sander AIR 658 User Manual
Amana Dishwasher L0503010 User Manual
ATN Binoculars ATN PS 15 User Manual
Behringer Speaker B208D User Manual