For Setup & Operation Videos Go To:
HAVING TROUBLE W/ YOUR SOUND SYSTEM?
CONDITION
No Sound (power LED off)
POSSIBLE SOLUTION
• turn POWER switch ON
• charge battery or plug in AC cord
• leave plugged in for 48 hours to repair battery
• check for output from source
Charge Indicator LED off
No Sound (power LED on)
• set Internal Speaker switch to ON
• make sure all cables are completely plugged in
• turn up volume control of input used
• remove plug from speaker output if not using external speaker output
• charge battery fully; if battery life continues to deteriorate, contact
Anchor Audio customer service: (888) 444-6077
• lower system volume control
Shortened Battery Life
Distorted Sound
Excessive Hum or Noise
• use shielded cables
• use balanced microphone
HAVING TROUBLE W/ YOUR WIRELESS SYSTEM? (WIRELESS MODELS ONLY)
CONDITION
No Sound (RX Indicator: ON)
POSSIBLE SOLUTION
• set MUTE switch to on (handheld mic only)
• turn up WIRELESS volume control
• make sure mic is plugged into body pack transmitter
• push mic power button
No Sound (RX Indicator: OFF)
• turn Acclaim POWER switch on
• make sure transmitter power switch is on
• set receiver and transmitter to same channel
• replace battery in transmitter
ANCHOR AUDIO CUSTOMER SERVICE
ACCLAIM
888/444-6077
310/784-2300
pORTABLE LECTERN SOUND SYSTEM
ACCLAIM TECHNICAL SpECIFICATIONS
Rated Power Output
Max SPL @ Rated Power
Frequency Response
AC Power Requirements
Dimensions
22 watts
114 dB @ 1 meter
60 Hz – 15 kHz ± 3 dB
Sensitivity For Rated Output
Lo-Z Microphone
Hi-Z Microphone
-52 dBV (2.5 mVrms)
-43 dBV (7.5 mVrms)
-14 dBV (200 mVrms)
OWNER’S MANUAL
90 – 264 VAC, 50/60 Hz, 50 W max Auxiliary (line)
Outputs
14 x 22.5 x 13.5”/ 35.6 x 57 x 34.3 Line (post fader)
Microphone
CONTENTS
Base (HWD)
cm
Lo-Z (<1k ohm), buffered, 1/4” phone
Lo-Z, balanced, XLR
switched – 8ohm, 1/4” phone
unswitched – 4ohm, 1/4” phone
GETTING STARTED ......................................................................................................................................... 2
CARING FOR YOUR BUILT-IN BATTERIES.......................................................................................................... 3
ACCLAIM LECTERN BASIC SYSTEM OPERATION............................................................................................ 4/5
OPERATING THE BUILT-IN UHF WIRELESS RECEIVER......................................................................................... 6
ACCLAIM ACCESSORIES.................................................................................................................................. 6
OPERATING THE WIRELESS MICROPHONE / TRANSMITTER............................................................................... 7
HAVING TROUBLE W/ YOUR SOUND SYSTEM? ................................................................................................ 8
ACCLAIM SOUND SYSTEM TECHNICAL SPECIFICATIONS.................................................................................... 8
Table Top
22.5 x 19” / 57 x 48 cm
Speaker
Weight
30 pounds / 13.6 Kg
Inputs
ACL-BASE
Lectern Mic
Lo-Z, balanced, phantom power, XLR
Dimensions (HWD)
30.5 x 21.5 x 18.5”/ 77.5 x 54.6 x 47
38 pounds / 17.2 Kg
Auxiliary Mic
Line
Lo-Z, balanced, phantom power, XLR cm
Hi-Z, unbalanced, 1/4” phone Weight
(Specifications subject to change without notice)
Anchor Audio, Inc.
Portable Sound Systems
•
Torrance, California
100-0163-000/C - 4/09
Download from Www.Somanuals.com. All Manuals Search And Download.
DIVERSITY WIRELESS BY ANCHOR AUDIO
Anchor Audio UHF wireless is a 16 channel, diversity wireless system that receives signals with two independent antennae. With diversity
wireless the receiver processes the stronger signal, effectively minimizing dropouts and interference from other transmitting sources. The
antennae are mounted internally so there are no obstructions or risk of damage.
CARING FOR YOUR BUILT-IN BATTERIES
It is very important that you fully charge the batteries in your new sound system before the first time its used. To preserve battery life it is also
recommended that batteries be fully charged as soon as possible after every use regardless of the length of operation.
UNDERSTANDING THE BATTERY LEVEL INDICATOR LIGHT
CHANNEL SELECTION - BUILT-IN RECEIVER
LED Flashing Red
Battery charge is very low, in 15-30 minutes the Battery Protection Circuit will turn the system off
WIRELESS MICROPHONE
VOLUME CONTROL
WIRELESS RECEIVER CHANNEL
Select a channel, set the built-in receiver and micro-
phone transmitter to that channel before using your
wireless system.
SELECTION KNOB
LED Off
Battery is completely drained and must be charged
NOTE: System Can Be Used When Batteries Are Being Charged!
1. Choose any available wireless channel/
frequency from 1 thru 16
OPERATING ACCLAIM IN AC MODE
(transmitter instructions - page 7)
Plug your sound system into an AC outlet and operate as normal while charging the built-in batteries at the same time. The Charger LED will
light during charging and flash when the battery is fully charged.
2. Set the Wireless Channel Selector Knob to
the channel/frequency you choose in step
1 above
BATTERY SERVICE TIME
With the batteries fully charged you can expect approx.:
Remember, to operate the receiver & transmitter
pair must be set to the same channels.
6-8 hrs @ Medium Volume
2-4 hrs @ Full Volume
Of continuous music input (longer for speech). However service time will vary depending on control settings and the use of accessories (built-in
CD player, wireless receivers and/or a companion speaker).
RX INDICATOR LIGHTS
IMpORTANT: Always Store Your System w/ Batteries Fully Charged!
NOTE: Ongoing wireless interference? The frequency you selected may be in use by
SYSTEM STORAGE & BATTERIES
other systems in the area! Change channels until you find a clear frequency!
Always store your sound system with the batteries fully charged. For extended periods of storage leave the system plugged into an AC outlet. If
this is not possible, charge the system at least once each month for a minimum of 24 hours.
NEED MORE HELp? View demonstration videos on proper system setup and operation:
ACCLAIM ACCESSORIES
AN-1001X - Companion Speaker
Unpowered companion speaker (speaker cable not included)
ACC-BASE - Base for Acclaim
Acclaim lectern base & traveling case
CHARGER
INDICATOR LIGHT
SC-50 - Heavy Duty Speaker Cable
50’ speaker cable, connect AN-1001X to powered Acclaim
MIC-90 - Handheld Wired Microphone
Anchor’s dynamic, balanced, low impedance microphone w/ unidi-
rectional pick-up pattern, mic “on/off” switch & 20’ cable
SS-550 - Heavy Duty Speaker Stand
Adjustable stand made of black, anodized aluminum
BATTERY LEVEL
INDICATOR LIGHT
CHARGING YOUR BUILT-IN BATTERIES
An automatic charging system is built-in to your Acclaim Lectern Sound System. It is designed to properly charge and maintain the systems
built-in batteries. To charge the batteries:
ANCHOR WIRELESS - 16 CHANNEL UHF
WH-6000 - Handheld Microphone/Transmitter
Wireless transmitter & microphone in one unit
WB-6000 - Body Pack Transmitter
Works w/ hands free microphones (mic not included)
1. Plug the power cord into your sound system
2. Plug the other end of the cord into AC outlet (Charger LED will stay on during charging)
3. Batteries will be fully charged in approximately 6-8 hrs (Charger LED will flash)
Body Pack Transmitter Microphones:
CM-60 - Collar Microphone
Lightweight, low-profile mic
LM-60 - Lapel Microphone
Lightweight, clip-on lapel mic
When in AC mode the system automatically transfers power from the battery charger to the power amplifier at high volume output, causing the
Charger LED to flicker.
EM-60T - UltraLite Microphone
Hands free “Over-the-Ear” mic
HBM-TA4F - Headband Microphone
Ultra-lightweight headband mic
6
3
Download from Www.Somanuals.com. All Manuals Search And Download.
LINE IN
INPUT JACK – 1/4” PHONE
BASIC SYSTEM OpERATION
Jack may be combined w/ mic inputs for a composite output
For playback of tape/CD player or other audio source
NOTE: Fully Charge Battery Before First DC Use!
CHARGE INDICATOR LIGHT
(please see page 3 for instructions)
BATTERY LEVEL INDICATOR LIGHT
1. Set all Input Level Controls to minimum & Tones Controls to flat (the
middle setting) before turning your system on
LINE OUT
2. Plug lectern gooseneck microphone into the Lectern Mic Jack located on
the tabletop
OUTPUT JACK – 1/4” PHONE
Balanced - provides combined
output of all active system inputs
Record presentation / connect to another
powered sound system
3. Plug reading light into the Reading Lamp Jack on control panel
4. Switch POWER to ON, the BATTERY LED will light
5. Slowly increase the Level Control for the input jacks used
to the desired volume
INTERNAL SPEAKER SWITCH
Turn internal lectern speaker out-
put on / off
6. Adjust BASS & TREBLE controls to desired sound quality
ACCLAIM LECTERN -
CONNECTION pANEL
Model Shown: ACL-7500U1
IMpORTANT: Make all connections w/ shielded
cables to avoid hum, buzzing or interference.
AUXILIARY MICROPHONE
INPUT JACK – XLR
Balanced - low impedance mi-
crophones, powers condenser
mics
BALANCED MICROPHONE
OUTPUT JACK – XLR
Use to connect Acclaim to a
house system
SPEAKER OUT
OUTPUT JACK – 1/4” PHONE
Balanced - drives an unpowered
2 ohm speaker in addition to the
built-in speakers
UHF WIRELESS RECEIVER
Available on selected models only
(please see page 6 for instructions)
POWER ON
INDICATOR LIGHT
WIRED MICROPHONE
LEVEL CONTROL
TONE CONTROLS
Bass & Treble
LECTERN
MICROPHONE
JACK
READING LAMP JACK
Remove cap to use
LINE IN LEVEL
CONTROL
LECTERN MIC LEVEL
CONTROL
ACCLAIM LECTERN - CONTROL pANEL
Model Shown: ACL-7500U1
FRONT/SPEAKER
LECTERN TOP
ACCLAIM LECTERN
- TABLETOp
Waste electrical and electronic products must not be disposed of with household
waste. Please recycle where facilities exist. Check with your Local Authority or
Retailer for recycling advice.
All Models
BACK/CONTROL PANEL
4
Download from Www.Somanuals.com. All Manuals Search And Download.
|