|
10/100Mbps Dual Speeds
Fast Ethernet
PC Card Network Adapter
Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE INSTALLATION
1. Locate the PCMCIA slot of your system.
2. Align the PCMCIA Fast Ethernet PC Card
toward the PCMCIA slot. Push evenly and
steadily until it is seated.
3. Plug one end of an Ethernet Cable into the RJ-45
port of the Media Coupler.
Media Coupler
Ethernet HUB/Switch
4. You are now ready to continue the software
installation.
- 1 -
Download from Www.Somanuals.com. All Manuals Search And Download.
LED Indicators
ꢁ
ꢁ
ꢁ
Act: Glows green when it is on,
blinks when transmitting data.
10/100: Glows orange at 100Mbps,
dims at 10Mbps.
Link: Glows green when linked to a
local
network,
blinks
when
receiving data.
Green
Activity: on
TX
: blink
Orange
100Mbps: On
10Mbps :Off
Green
Link Integrity: on
RX
: blink
- 2 -
Download from Www.Somanuals.com. All Manuals Search And Download.
SOFTWARE INSTALLATION
Installation for Windows 95
The installation procedures for the network driver
may vary slightly depending on the version of
Windows 95 you are using and also your current
system configuration.
1. Once the PCMCIA Fast Ethernet PC Card
is connected to your computer, Windows 95
will automatically detect the new hardware
device. Insert the program diskette #1 into
your floppy drive.
2. Click Next. When the PCMCIA Fast
Ethernet PC Card message appears, click
Finish. The Installation program will
continue to copy the necessary files into your
computer.
3. Follow the on-screen instruction to proceed.
If Windows asks you to supply your original
Windows 95 installation or setup files, insert
the CD-ROM or disks as requested, and
direct Windows 95 to the proper location.
4. When asked if you want to restart your
computer, click Yes.
Installation for Windows 98
1. Once the PCMCIA Fast Ethernet PC
Card is connected to your computer,
Windows 98 will automatically detect
the new hardware device as shown
below. Click Next.
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Insert the device driver diskette into
your floppy drive. When Windows
prompts you What do you want
Windows to do? Select Search for the
best
driver
for
your
device.
(Recommended). Click Next.
3. Follow the on-screen instruction to
proceed.
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4. The installation program will proceed
automatically.
5. In the following dialog box, direct your
system to copy the requested files from
the floppy root directory, i.e. A:\. Press
OK.
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
6. If you are asked to insert Windows 98
CD-ROM in the selective drive, please
do so to have Windows copy all the
necessary files to your system. . When
the following window appears, click
Finish.
7. Click Yes to restart your computer.
Installation for Window ME
1. Once the PC Card is well connected to your
computer, Windows ME will automatically
detect the new device. Select Automatic
search
for
a
better
driver
(Recommended) … and click Next.
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
3.
Insert the device driver disk into the floppy
disk drive on your system.
Windows will copy the appropriate driver
to your system. If Windows ME asks you
to supply your original Windows ME
installation CD-ROM, load it on the CD-
ROM drive. Click Finish to complete the
software installation.
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
Reboot your computer to activate the new
device.
Installation for Windows 2000
1. Insert the PC Card into the slot. When the
Found New Hardware Wizard dialog box
appears, press Next.
2. When Windows prompt you a Found New
Hardware Wizard dialog box, select
Search for a … and press Next.
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Windows will prompt
a
Found New
Hardware Wizard dialog box. In this time,
select Floppy disk drives and insert the
driver diskette. Press Next. When asked for
the original Windows 2000 CD/disks please
follow the on-screen instruction.
- 9 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Wait for a while until Windows has found
the appropriate driver.
5. Click Yes to continue.
6. Click Finish.
The PC Card driver
installation is successfully completed.
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
7. For the first time installation, click Network
icon in Control Panel to add Protocols,
Client and Service if needed.
8. Reboot your computer to activate the new
device.
Installation for Windows XP
1.
Once the device is well connected,
Windows will detect the new device and
prompt you to insert the network device
driver. Insert the device Driver Disk into
the floppy disk drive of your system. Click
Install the software automatically
(Recommended) and click Next.
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
Windows will start searching for the
appropriate driver for this hardware. Select
any drivers named as PCMCIA Fast
Ethernet Card, and click Next.
3.
Windows will start searching for the
appropriate driver for the installation.
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
When the screen appears as below, click
Continue Anyway to proceed.
4.
5.
Wait while Windows copies the appropriate
driver to your system.
Click Finish. The software installation for
this network device is now completed.
- 13 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation for Windows NT 4.0
This section describes the installation for
Windows NT under the condition that Windows
NT is already installed in your computer. If your
computer is not yet networking installed, refer to
the Windows documentation for details. Also
remember to have your original Windows NT
CD-ROM handy before you begin the installation.
For Windows NT may ask for it during the
installation.
1. Before you turn on your computer, make
sure the PCMCIA Fast Ethernet PC Card
has been properly inserted into the free
PCMCIA slot of your computer.
2. Start Windows NT.
3. Click StartꢂSettingsꢂControl Panel.
Double-click on the Network icon.
4. When the Network window appears, click on
the Adapters tab. Click on the Add button,
followed by Have Disk. Put the driver disk
into drive A.
5. When asked to supply the path to the disk,
type a:\ and click OK.
6. Windows NT will ask you to supply the I/O
Base, Interrupt, and Memory values for the
card. Good values to start with are 300 (for
the I/O Base) and 5 (for the IRQ).
7. When you're finished, click OK. Windows
NT will copy necessary files to your
computer.
- 14 -
Download from Www.Somanuals.com. All Manuals Search And Download.
8. When the Network window reappears, click
on the Bindings tab. Choose your bindings.
Click on the Protocols tab and select your
settings. Do the same for the Services tab.
9. After your bindings, settings, and services
are set, click on the Close button. Choose to
restart your computer. After Windows NT
restarts, be sure to log in.
- 15 -
Download from Www.Somanuals.com. All Manuals Search And Download.
|