Installation and Operating Manual
HYBRID GAS WATER HEATERS
POWER VENT GAS MODELS
CSA 4.3b-2008
ANSI Z21.10.3b-2008
• For Your Safety •
AN ODORANT IS ADDED TO THE GAS USED
BY THIS WATER HEATER.
ALL TECHNICAL AND WARRANTY QUESTIONS: SHOULD BE DIRECTED TO THE LOCAL DEALER FROM WHOM THE WATER HEATER WAS
PURCHASED.
KEEP THIS MANUAL IN THE POCKET ON HEATER FOR FUTURE REFERENCE
WHENEVER MAINTENANCE ADJUSTMENT OR SERVICE IS REQUIRED.
PRINTED IN U.S.A. 0610
316888-000 Rev. 00
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFE INSTALLATION, USE AND SERVICE
Your safety and the safety of others is extremely important in the installation, use and servicing of this water heater.
Many safety-related messages and instructions have been provided in this manual and on your own water heater to warn you and
others of a potential injury hazard. Read and obey all safety messages and instructions throughout this manual. It is very important
that the meaning of each safety message is understood by you and others who install, use or service this water heater.
All safety messages will generally tell you about the type of hazard, what can happen if you do not follow the
safety message and how to avoid the risk of injury.
The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a
list of substances known to the State of California to cause cancer, birth defects, or other reproductive harm,
and requires businesses to warn of potential exposure to such substances.
This product contains a chemical known to the State of California to cause cancer, birth defects, or other
reproductive harm. This appliance can cause low level exposure to some of the substances listed.
IMPORTANT DEFINITIONS
• Qualified Installer or Service Agency: Installation and service of this water heater requires ability equivalent to that
of a Qualified Agency (as defined by ANSI below) in the field involved. Installation skills such as plumbing, air supply,
venting, gas supply, electrical supply are required in addition to electrical testing skills when performing service.
• ANSI Z223.1 2006 Sec. 3.3.83: “Qualified Agency” - “Any individual, firm, corporation or company that either in person
or through a representative is engaged in and is responsible for (a) the installation, testing or replacement of gas piping
or (b) the connection, installation, testing, repair or servicing of appliances and equipment; that is experienced in such
work; that is familiar with all precautions required; and that has complied with all the requirements of the authority
having jurisdiction.”.
• Gas Supplier: The Natural Gas or Propane Utility or service who supplies gas for utilization by the gas burning appliances
within this application. The gas supplier typically has responsibility for the inspection and code approval of gas piping
up to and including the Natural Gas meter or Propane storage tank of a building.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
GENERAL SAFETY
DANGER
Flammable Vapors
Vapors from flammable
liquids may explode and
catch fire causing death or
severe burns.
Water heater has a main
burner and spark generator.
The spark generator:
1. can be triggered at any
time and
Do not use or store
2. the spark will ignite
flammable vapors.
flammable products such as
gasoline, solvents or adhe-
sives in the same room or
area near the water heater.
Vapors:
1. cannot be seen,
2. are heavier than air,
3. go a long way on the floor
and
Keep flammable products:
1. far away from heater,
2. in approved containers,
3. tightly closed and
4. can be carried from other
rooms to the the
4. out of children's reach.
electodes by air currents.
Installation: Do not install the water heater where flammable
products will be stored or used.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
INTRODUCTION
Thank You for purchasing this water heater. Properly
installed and maintained, it should give you years of trouble
free service.
5. Carefully plan the place where you are going to put
the water heater. Correct combustion, vent action, and
vent pipe installation are very important in preventing
death from possible carbon monoxide poisoning and
fires (see Figures 1 and 3). Examine the location to
ensure the water heater complies with the “Facts to
Consider About Location” section in this manual.
6. For California installation this water heater must be
braced, anchored, or strapped to avoid falling or
moving during an earthquake. See instructions for
correct installation procedures. Instructions may be
obtained from California Office of the State Architect,
400 P Street, Sacramento, CA 95814.
7. Massachusetts Code requires this water heater to be
installed in accordance with Massachusetts 248-CMR
2.00: State Plumbing Code and 248-CMR 5.00, See
page 8.
8. Complies with SCAQMD rule #1146 and districts
having equivalent NOx requirements.
Abbreviations Found In This Instruction Manual:
•
•
•
•
•
•
CSA - Canadian Standards Association
ANSI - American National Standards Institute
NFPA - National Fire Protection Association
ASME - American Society of Mechanical Engineers
GAMA - Gas Appliance Manufacturer’s Association
UL - Underwriters Laboratories Inc.
This gas-fired water heater is design certified by CSA
International under American National Standard/CSA
Standard for Gas Water Heaters ANSI Z21.10.3 • CSA
4.3 (current edition).
PREPARING FOR THE INSTALLATION
1. Read the “General Safety” section, of this manual
first and then the entire manual carefully. If you
don’t follow the safety rules, the water heater will not
operate properly. It could cause DEATH, SERIOUS
BODILY INJURY AND/OR PROPERTY DAMAGE.
9. Complies with California’s legislation AB1953 and
Vermont’s legislation Act 193 requirement of a
weighted average maximum of 0.25% lead.
This manual contains instructions for the installation,
operation, and maintenance of the gas-fired water
heater. You must read and be aware of the warnings
placed throughout the manual. All warnings and all
instructions are essential to the proper operation of
the water heater and your safety. Since we cannot put
everything on the first few pages, READ THE ENTIRE
MANUAL BEFORE ATTEMPTING TO INSTALL OR
OPERATE THE WATER HEATER.
2. The installation must conform with these instructions
and the local code authority having jurisdiction. In
the absence of local codes, the installation must
comply with the current editions of the National Fuel
Gas Code, ANSI Z223.1/NFPA 54 and the National
Electrical Code, NFPA 70. Documents are available
from:
Canadian Standards Association,
5060 Spectrum Way,
Mississauga, Ontario, Canada
L4W 5N6
NFPA documents are also available from:
National Fire Protection Association,
1 Batterymarch Park,
Quincy, MA 02269.
3. The water heater when installed must be grounded in
accordance with the local codes, or in the absence of
local codes: the National Electrical Code (NFPA 70).
4. If after reading this manual you have any
questions or do not understand any portion of
the instructions, call the local gas utility or the
manufacturer whose name appears on the rating plate.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
GET TO KNOW YOUR WATER HEATER - GAS MODELS
A Mixing Valve***
B Hot Water Outlet (Tempered)***
C Pipe Insulation***
D Inlet Water Shutoff Valve***
E Cold Water Inlet***
U Side Casing (Plastic)
V Top Casing Enclosure (Plastic)
W Exhaust Elbow Assembly
X T&P Relief Valve
Y Anode
F Expansion Tank***
Z Inlet Dip Tube
G Vent Termination Elbow**
H Access Door (Heat Engine)
I Earthquake Strap***
J Power Cord*
K Main Manual Gas Shutoff Valve***
L Gas Supply***
* CAUTION HARNESS HAS 120 VAC. IN
OPERATION.
** See “Planning the Vent System,” “Installation
of Vent System” and “Condensate” for more
information.
M Sediment Pocket***
N Condensate Tube
*** These items not included.
O Drain Pan***
P Drain Valve
Q Heat Engine Hose - Cold In
R Casing Door (Plastic)
S Display Enclosure (Plastic)
T Heat Engine Hose - Hot Out
REPLACEMENT PARTS AND DELIMING
PRODUCTS
A
C
B
D
E
Replacement parts and recommended delimer may be ordered through
authorized servicers or distributors. When ordering parts, provide complete
model and serial numbers (see rating plate), quantity and name of part
desired. Standard hardware items may be purchased locally.
V
F
U
T
X
G
H
I
S
N
W
J
K
L
Y
Z
M
R
O
Q
P
N
FIGURE 1
8
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION CONSIDERATIONS
ROUGH IN DIMENSIONS
Top View
Left Side View
FIGURE 2
Capacity, Gas and Electrical Characteristics
Model
Approx. Capacity
Input
Gas
Type
Gas Supply Pressure
Manifold Pressure Electrical Characteristics
U.S. Gals. Litres BTU/hr
Max.
Min.
in. WC (kPa)
Volts/Hz
Amperes
in. WC (kPa) in. WC (kPa)
HYB-90N
25
94.6
100,000 Nat.
14.0 (3.49) 5.0 (1.25)
4.2 (1.05)
120/60
2.5
Minimum gas supply pressure must be maintained under both load and no load (dynamic and static) conditions.
Manifold Pressure is preset on the gas valve by the manufacturer; DO NOT ATTEMPT TO ADJUST!
Thermal efficiency is 90%.
If the hardness of your water supply is more than of 12 grains per gallon (200 mg/L), if your water supply is acidic or otherwise impure,
the water supply must be treated with approved methods in order to ensure full warranty coverage. Problems resulting from the forma-
tion of scale are not covered by the warranty.
Minimum Clearance To Combustibles
Service Clearance
Test Pressure
P.S.I.
Top
0
Front
0
Vent
0
Back
0
Sides
0
Floor
0
Front
21” (53.3 cm)
Sides
12” (30.5 cm)
300
This appliance must be installed in accordance with local codes or, in the absence of local codes, the “National Fuel Gas Code” ANSI
Z223.1/NFPA 54 or the “Natural Gas and Propane Installation Code” CAN/CSAB149.1.
Not for installation in a Manufactured Home (Mobile Home).
This water heater is suitable for water (potable) heating only.
This water heater is suitable for installation in a closet or alcove.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
INSTALLATION REQUIREMENTS FOR THE COMMONWEALTH OF MASSACHUSETTS
For all side wall terminated, horizontally vented power vent, gas fueled water heaters installed in every dwelling, building
or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth
and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in the area of the
venting, including but not limited to decks and porches, the following requirements shall be satisfied:
INSTALLATION OF CARBON MONOXIDE DETECTORS At the time of installation of the side wall horizontal vented gas fueled
equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up
is installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that
a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building
or structure served by the sidewall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure
the services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors.
In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard
wired carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall
have a period of thirty (30) days to comply with the above requirements provided that during said thirty (30) day period, a
battery operated carbon monoxide detector with an alarm shall be installed.
APPROVED CARBON MONOXIDE DETECTORS Each carbon monoxide detector as required in accordance with the
above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and CSA certified.
SIGNAGE A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum
height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled
heating appliance or equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, “GAS VENT
DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS.”
INSPECTION The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve
the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in
accordance with the provisions of 248 CMR 5.08(2)(a) 1 through 4.
EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54
as adopted by the Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the
dwelling, building, or structure used in whole or in part for residential purposes.
MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED When the manufacturer
of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system
components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the
venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED When the manufacturer
of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue
gases, but identifies “special venting systems,” the following requirements shall be satisfied by the manufacturer:
1. The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions;
and
2. The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include
a parts list and detailed installation instructions.
A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting
instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or
equipment at the completion of the installation.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
WATER PIPING - MIXING VALVE USAGE
SUGGESTED PIPING
ARRANGEMENT
FOR TOP
CONNECTIONS
TEMPERED
SHUT-OFF VALVE
POTABLE WATER
TEMPERED
POTABLE WATER
COLD WATER
INLET
THERMAL
EXPANSION
TANK
TEMPERATURE-
PRESSURE
RELIEF VALVE
MIXING
VALVE
DISCHARGE
PIPE (DO NOT
CAP OR PLUG)
(OPTIONAL)
PIPE INSULATION
(RECOMMENDED)
METAL
DRAIN PAN
6 in.
(15cm)
MAX.
AIR GAP
FLOOR
DRAIN VALVE
DRAIN
TO SUITABLE
DRAIN
FIGURE 3
This appliance has been design certified as complying with
ANSI Z21.10.3/CSA4.3 (latest revision) for water heaters
and is considered suitable for:
Water (Potable) Heating: All models are considered
suitable for water (potable) heating.
DO NOT use any pumps, valves, or fittings that are not
compatible with potable water.
DO NOT use valves that may cause excessive restriction
to water flow. Use full flow ball or gate valves only.
DO NOT use any lead based solder in potable water
lines. Use appropriate tin-antimony or other equivalent
material.
DO NOT tamper with the gas control/thermostat, igniter,
flammable vapor sensor or temperature and pressure
relief valve. Tampering voids all warranties. Only qualified
service technicians should service these components.
DO NOT use with piping that has been treated with
chromates, boiler seal, or other chemicals.
DO NOT add any chemicals to the system piping which
will contaminate the potable water supply.
HOTTER WATER CAN SCALD:
Water heaters are intended to produce hot water. Water
heated to a temperature which will satisfy space heating,
clothes washing, dish washing, and other sanitizing needs
can scald and permanently injure you upon contact. Some
people are more likely to be permanently injured by hot
water than others. These include the elderly, children,
and the physically or developmentally disabled. If anyone
using hot water from this heater fits into one of these
Please note the following:
The system should be installed only with piping that is
suitable for potable (drinkable) water such as copper,
CPVC, PEX or polybutylene. DO NOT use PVC water
piping.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
groups or if there is a local code or state law requiring a
certain temperature water at the hot water tap, then you
must take special precautions. In addition to using the
lowest possible temperature setting that satisfies your hot
water needs, a means such as a Mixing Valve, should be
used at the hot water taps used by these people or at the
water heater (see Figure 3). Mixing valves are available at
plumbing supply or hardware stores. Consult a Qualified
Installer or Service Agency. Follow the mixing valve
manufacturer’s instructions for installation of the valves.
Before changing the factory setting on the thermostat, read
the “Temperature Regulation” section in this manual.
such a manner that if the tank or any connections should
leak, the flow will not cause damage to the structure. For
this reason, it is not advisable to install the water heater
in an attic or upper floor. When such locations cannot be
avoided, a suitable metal drain pan should be installed
under the water heater. Drain pans are available at your
local hardware store. Such a drain pan must have a
clearance of at least 1.0 in. (2.5cm) greater than any point
on the water heater’s outer jacket and must be piped to
an adequate drain. The pan must not restrict combustion
air flow. See Figure 1.
Water heater life depends upon water quality, water
pressure and the environment in which the water heater
is installed. Water heaters are sometimes installed in
locations where leakage may result in property damage,
even with the use of a drain pan piped to a drain. However,
unanticipated damage can be reduced or prevented by a
leak detector or water shut-off device used in conjunction
with a piped drain pan. These devices are highly
recommended and are available from some plumbing
supply wholesalers and retailers, and detect and react to
leakage in various ways:
FACTS TO CONSIDER ABOUT LOCATION
Carefully choose an indoor location for the new water
heater, because the placement is a very important
consideration for the safety of the occupants in the building
and for the most economical use of the appliance. This
water heater is not for use in manufactured (mobile)
homes or outdoor installation.
Whether replacing an old water heater or putting the water
heater in a new location, the following critical points must
be observed:
1. Select a location indoors as close as practical to the
vent terminal or location to which the water heater vent
piping is going to be connected, and as centralized
with the water piping system as possible.
2. A pressure-reducing valve and/or an expansion tank
may be required for installations where the water
pressure is high. The pressure-reducing valve should
be located on the supply to the entire house in order
to maintain equal hot and cold water pressure.
3. Selected location must provide adequate clearances
for servicing and proper operation of the water
heater.
•
•
•
•
Sensors mounted in the drain pan that trigger an alarm
or turn off the incoming water to the water heater when
leakage is detected.
Sensors mounted in the drain pan that turn off the water
supply to the entire building when water is detected in
the drain pan.
Water supply shut-off devices that activate based on
the water pressure differential between the cold water
and hot water pipes connected to the water heater.
Devices that will turn off the gas supply to a gas water
heater while at the same time shutting off its water
supply.
AVOIDAREASWHEREFLAMMABLELIQUIDS(VAPORS)
ARE LIKELYTO BE PRESENT OR STORED (GARAGES,
STORAGE AND UTILITY AREAS, ETC.): Flammable
liquids (such as gasoline, solvents, propane (LP or butane,
etc.) and other substances (such as adhesives, etc.)) emit
flammable vapors which can be ignited by a gas water
heater’s igniter or main burner. The resulting flashback
and fire can cause death or serious burns to anyone in
the area.
4. Avoid locations that could cause the water heater to
freeze from outside air.
5. Selected location must provide access to a properly
grounded electrical branch circuit. A dedicated circuit
is preferred. Do not use a GFI outlet.
Important: Do not use an extension cord to connect the
water heater to an electrical outlet.
Important: The electrical controls used inside the gas
control of this water heater are polarity sensitive. Ensure
the electrical supply is connected correctly in the receptacle
box. Failure to connect correctly will prevent the unit from
functioning properly.
Also, the water heater must be located and/or protected so
it is not subject to physical damage by a moving vehicle.
Installation of the water heater must be accomplished in
12
Download from Www.Somanuals.com. All Manuals Search And Download.
DANGER
Flammable Vapors
Vapors from flammable
liquids may explode and
catch fire causing death or
severe burns.
Water heater has a main
burner and spark generator.
The spark generator:
1. can be triggered at any
time and
Do not use or store
2. the spark will ignite
flammable vapors.
flammable products such as
gasoline, solvents or adhe-
sives in the same room or
area near the water heater.
Vapors:
1. cannot be seen,
2. are heavier than air,
3. go a long way on the floor
and
HANDLE INSTALLATION
Keep flammable products:
1. far away from heater,
2. in approved containers,
3. tightly closed and
4. can be carried from other
rooms to the the
For ease of handling and carrying, plugs are provided
in the side of the shroud that can be removed and pipe
handles inserted (see Figure 4).
4. out of children's reach.
electodes by air currents.
Installation: Do not install the water heater where flammable
products will be stored or used.
•
•
Remove plastic plugs from shroud side panels.
Screw a short length of 3/4” NPT pipe into the sides of
the water heater.
•
Use the handles to move the water heater to the desired
location.
•
•
Remove the handles.
Reinstall the plastic plugs in the shroud side panels.
Handle
Handle
This water heater must not be installed directly on
carpeting. Carpeting must be protected by metal or wood
panel beneath the appliance extending beyond the full
width and depth of the appliance by at least 3in. (7.6cm)
in any direction, or if the appliance is installed in an alcove
or closet, the entire floor must be covered by the panel.
Failure to heed this warning may result in a fire hazard.
FIGURE 4
Download from Www.Somanuals.com. All Manuals Search And Download.
13
When installing the heater, consideration must be given to
proper location. Location selected should be as close to
the wall as practicable and as centralized with the water
piping system as possible.
Remove the right side panel
1. Use a screwdriver to remove the screw from the
bottom, front of the right side panel.
2. Remove the three screws from the right side panel
towards the rear of the unit.
3. Remove the screw from the top of the unit.
4. Push the panel back and lift out.
Remove the left side panel
1. Use a screwdriver to remove the screw from the
bottom, front of the left side panel.
2. Remove the three screws from the left side panel
towards the rear of the unit.
FIGURE 5
3. Remove the screw from the top of the unit.
4. Push the panel back and lift out.
Minimum clearances between the water heater and
combustible construction are 0 in. at the sides and rear,
0 in. (0cm) from the front and 2 in. (5.08cm) from the top
(see Figure 5). If clearances stated on the heater differ
from these distances, install water heater according to
clearances stated on the heater.
Top Casing
Access To
(Front)
Door Pins
Door
Lock
Adequate top clearance of 24 in. (61cm) for servicing this
appliance, such as changing the anodes etc., should be
considered before installation.
Screws
A minimum front clearance of 20 in. (51cm) and 10 in.
(26cm) of side clearance must be allowed for access to
replaceable parts.
EARTHQUAKE ZONES
In Earthquake Zones the water heater must be braced,
anchored, or strapped to avoid moving during an
earthquake. Contact local utilities for code requirements in
your area. The Spacemaker® TSE25 Bear Claw™ Water
Heater Strap is suitable for bracing the Hybrid water heater.
Follow the manufacturer’s instructions for installing the
braces. Be sure to wear protective goggles and gloves
when handling any kind of sheet metal product.
Tabs have been provided on each side of the rear portion
of the shroud. The top and bottom of each tab must be
cut and gently bent “inwards” thus allowing the straps to
exit the shroud (see Figure 9).
FIGURE 6
In order to access the tabs and install the earthquake
straps it is necessary to remove the top, front and side
panels of the shroud as follows (see Figures 6 - 8):
Door opening
1. Unlock the door by rotating the lock counter-clockwise
with a wide, slot screwdriver.
2. Release the top and bottom door pins by prying the
pins out, using a small screwdriver.
3. Open the door (the door remains fastened to the left
side panel).
Remove the top casing (front).
1. Use a screwdriver to remove the six screws securing
the top casing.
2. Lift up and remove casing top (front).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Screws
Screws
Top
Casing (Front)
FIGURE 7
Screws
FIGURE 9
After the heater has been positioned and the earthquake
straps have been installed, re-assemble the shroud in the
reverse order.
FIGURE 8
Download from Www.Somanuals.com. All Manuals Search And Download.
15
COMBUSTION AIR AND VENTILATION
In unconfined spaces in buildings, infiltration may be
adequate to provide air for combustion, ventilation and
dilution of flue gases. However, in buildings of tight
construction (for example, weather stripping, heavily
insulated, caulked, vapor barrier, etc.), additional air may
need to be provided using the methods described in
“Appliances in Confined Space” that follows.”
A gas water heater cannot operate properly without the
correct amount of air for combustion. Do not install in a
confined area such as a closet, unless you provide air as
shown in the “Facts to Consider About Location” section.
Never obstruct the flow of ventilation air. If you have any
doubts or questions at all, call your gas supplier. Failure to
provide the proper amount of combustion air can result in
a fire or explosion and cause death, serious bodily injury,
or property damage.
APPLIANCES IN CONFINED SPACES
CONFINED SPACE is a space whose volume is less than
50 cubic feet per 1,000 Btu per hour (4.8cm per kW) of
the aggregate input rating of all appliances installed in
that space.
When drawing combustion air from inside a building to a
confined space, such a space should be provided with two
permanent openings. ONE WITHIN 12 in. (30cm) OF THE
ENCLOSURE TOP AND ONE WITHIN 12 in. (30cm) OF
THE ENCLOSURE BOTTOM. Each opening should have
a free area of 1 square inch per 1000 Btu/hr (22 cm2/kW)
of the total input of all appliances in the enclosure, but not
less than 100 square in. (645 cm2).
If the confined space is within a building, air for combustion
and ventilation must be obtained from outdoors. When
directly communicating with the outdoors or communicating
through vertical ducts, two permanent openings, located
in the above manner, should be provided. Each opening
should have a free area of not less than 1 square inch per
4000 Btu/hr (5.5 cm2/kW) of total input of all appliances in
the enclosure. If horizontal ducts are used, each opening
should have a free area of not less than 1 square inch per
2000 Btu/hr (11 cm2/kW) of the total input of all appliances
in the enclosure.
FIGURE 10
If this water heater will be used in beauty shops, barber
shops, cleaning establishments, or self-service laundries
with dry cleaning equipment, it is imperative that the water
heater(s) be installed so that all air for combustion and
ventilation is taken from outdoors.
A. ALLAIR FROM INSIDE BUILDINGS: (See Figures 10
& 11)
The confined space should be provided with two permanent
openings communicating directly with an additional
room(s) of sufficient volume so that the combined volume
of all spaces meets the criteria for an unconfined space.
The total input of all gas utilization equipment installed in
the combined space should be considered in making this
determination. Each opening should have a minimum free
area of 1 square inch per 1,000 Btu per hour (22 cm2/kW)
of the total input rating of all gas utilization equipment in
the confined space, but not less than 100 square in. (645
cm2). One opening should commence within 12 in. (30cm)
of the top and one commencing within 12 in. (30cm) of the
bottom of the enclosures.
Note: Vent length should be long enough that the outside
air will not freeze the water heater.
Propellants of aerosol sprays and volatile compounds,
(cleaners, chlorine based chemicals, refrigerants, etc.) in
addition to being highly flammable in many cases, will also
react to form corrosive hydrochloric acid when exposed to
the combustion products of the water heater. The results
can be hazardous, and also cause product failure.
APPLIANCES IN UNCONFINED SPACES
UNCONFINED SPACE is space whose volume is not less
than 50 cubic feet per 1,000 Btu per hour (4.8 cubic meters
per kW) of the aggregate input rating of all appliances
installed in that space. Rooms communicating directly with
the space in which the appliances are installed, through
openings not furnished with doors, are considered a part
of the unconfined space.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 11
FIGURE 13
B. ALLAIR FROM OUTDOORS: (See Figures 12, 13 and
14)
4. When ducts are used, they should be of the same
cross-sectional area as the free area of the openings to
which they connect. The minimum short side dimension
of rectangular air ducts should not be less than 3 in.
(7.6cm) (see Figure 14).
The confined space should be provided with two permanent
openings, one commencing within 12 in. (30cm) of the top
and one commencing within 12 in. (30cm) from the bottom
of the enclosure. The openings should communicate
directly, or by ducts, with the outdoors or spaces (crawl or
attic) that freely communicate with the outdoors.
1. When directly communicating with the outdoors, each
opening should have a minimum free area of 1 square
inch per 4,000 Btu per hour (5.5 cm2/kW) of total input
rating of all equipment in the enclosure (see Figure
12).
FIGURE 14
5. Alternatively a single permanent opening may be used
when communicating directly with the outdoors, or with
spaces that freely communicate with the outdoors. The
opening should have a minimum free area of 1 square
inch per 3,000 BTU per hour (8.3 cm2/kW) of total input
rating of all equipment in enclosure (see Figure 15).
FIGURE 12
2. When communicating with the outdoors through vertical
ducts, each opening should have a minimum free area
of 1 square inch per 4,000 Btu per hour (5.5 cm2/kW)
of total input rating of all equipment in the enclosure
(see Figure 13).
3. When communicating with the outdoors through
horizontal ducts, each opening should have a minimum
free area of 1 square inch per 2,000 Btu per hour (11
cm2/kW)) of total input rating of all equipment in the
enclosure (see Figure 14).
FIGURE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
17
6. Louvers and Grilles: In calculating free area,
consideration should be given to the blocking effect of
louvers, grilles or screens protecting openings. Screens
used should not be smaller than 1/4 in. (0.64cm) mesh.
If the free area through a design of louver or grille is
known, it should be used in calculating the size opening
required to provide the free area specified. If the design
and free area is not known, it may be assumed that
wood louvers will be 20-25 percent free area and metal
louvers and grilles will have 60-75 percent free area.
Louvers and grilles should be fixed in the open position
or interlocked with the equipment so that they are
opened automatically during equipment operation.
Water heaters are intended to produce hot water. Water
heated to a temperature which will satisfy space heating,
clotheswashing, dishwashing, cleaningandothersanitizing
needs can scald and permanently injure you upon contact.
Some people are more likely to be permanently injured by
hot water than others. These include the elderly, children,
the physically or developmentally disabled. If anyone using
hot water fits into one of these groups or if there is a local
code or state law requiring a certain temperature water at
the hot water tap, then you must take special precautions.
In addition to using the lowest possible temperature setting
that satisfies your hot water needs, a means such as a
*mixing valve, should be used at the hot water taps used
by these people or at the water heater (see Figure 3).
Valves for reducing point of use temperature by mixing
cold and hot water are also available:
7. Special Conditions Created by Mechanical Exhausting
or Fireplaces: operation of exhaust fans, ventilation
systems, clothes dryers or fireplaces may create
conditions requiring special attention to avoid
unsatisfactory operation of installed gas utilization
equipment.
Consult a Qualified Installer or Service Agency. Follow
manufacturer’s instructions for installation of the valves.
Before changing the factory setting on the thermostat, read
the “Temperature Regulation” section in this manual.
CHEMICAL VAPOR CORROSION
CORROSION OF THE FLUEWAYSAND VENT SYSTEM
MAY OCCUR IF AIR FOR COMBUSTION CONTAINS
CERTAINCHEMICALVAPORS. SUCHCORROSIONMAY
RESULT IN FAILURE AND RISK OF ASPHYXIATION.
Spray can propellants, cleaning solvents, refrigerator and
air conditioning refrigerants, swimming pool chemicals,
calcium and sodium chloride (water softener salt), waxes,
and process chemicals are typical compounds which are
potentially corrosive.
This water heater should not be connected to any heating
systems or component(s) used with a non-potable water
heating appliance.
All piping components connected to this unit should be
suitable for use with potable water.
Do not store products of this sort near the heater. Also, air
whichisbroughtincontactwiththeheatershouldnotcontain
any of these chemicals. If necessary, uncontaminated air
should be obtained from remote or outside sources. The
limited warranty is voided when failure of water heater is
due to a corrosive atmosphere. (See limited warranty for
complete terms and conditions).
Toxic chemicals, such as those used for boiler treatment
should not be introduced into this system.
When the system requires water for space heating at
temperatures higher than required for domestic water
purposes, a mixing valve must be installed. Please refer
to Figure 3 for suggested piping arrangement.
WATER PIPING
CLOSED WATER SYSTEMS
Water supply systems may, because of code requirements
or such conditions as high line pressure, among others,
have installed devices such as pressure reducing valves,
check valves, and back flow preventers. Devices such as
these cause the water system to be a closed system.
THERMAL EXPANSION
As water is heated, it expands (thermal expansion). In a
closed system, the volume of water will increase. As the
volume of water increases, there will be a corresponding
increase in water pressure due to thermal expansion.
Thermal expansion can cause premature tank failure
(leakage). This type of failure is not covered under the
HOTTER WATER CAN SCALD:
18
Download from Www.Somanuals.com. All Manuals Search And Download.
limited warranty. Thermal expansion can also cause
intermittent temperature-pressure relief valve operation:
water discharged from the valve due to excessive pressure
build up. The temperature-pressure relief valve is not
intended for the constant relief of thermal expansion. This
condition is not covered under the limited warranty.
HARD WATER
We highly recommend installing water filtering system or
a water softener before the water heater system. If you
are installing a water filtering system use a 5 micron filter
to reduce particles that can potentially cause nuisance
shutdown problems and prolong the maintenance of the
water heater’s inlet filter. A water softener can affect the
life of the anode installed in this water heater. Refer to
“Anode Rod Inspection” section in this manual.
A properly-sized thermal expansion tank should be
installed on all closed systems to control the harmful
effects of thermal expansion. Contact a plumbing service
agency or your retail supplier regarding the installation of
a thermal expansion tank.
Clean the filter on the water inlet as frequently as required
by the quality of your local water. Refer to “Cleaning The
Inlet Water Filter” section of this manual. One additional
filter is supplied with your water heater.
TEMPERATURE-PRESSURE RELIEF VALVE
NOTE: If using copper tubing, solder tubing to an
adapter before attaching the adapter to the water
heater connections. Do not solder the water lines
directly to the water heater connections. It will harm
the dip tube and damage the tank.
SHUT-OFF
VALVE
COLD WATER
INLET
TEMPERED
POTABLE WATER
This heater is provided with a properly certified combination
MIXING
temperature - pressure relief valve by the manufacturer.
VALVE
(OPTIONAL)
The valve is certified by a nationally recognized testing
laboratory that maintains periodic inspection of production
oflistedequipmentofmaterialsasmeetingtherequirements
for Relief Valves for Hot Water Supply Systems, ANSI
Z21.22 • CSA 4.4, and the code requirements of ASME.
PIPE INSULATION
(RECOMMENDED)
If replaced, the valve must meet the requirements of local
codes, but not less than a combination temperature and
pressure relief valve certified as indicated in the above
paragraph.
Rear View
The valve must be marked with a maximum set pressure
not to exceed the marked hydrostatic working pressure of
the water heater (150 psi = 1,035 kPa) and a discharge
capacity not less than the water heater Btu/hr input rate
as shown on the water heater’s rating plate.
For safe operation of the water heater, the relief valve
must not be removed from its designated opening nor
plugged.
FIGURE 16
NOTE: To protect against untimely corrosion of hot
and cold water fittings, it is strongly recommended
that di-electric unions or couplings be installed on
this water heater when connected to copper pipe (see
Figure 3 also).
Figures 3 and 16 show the typical attachment of the water
piping to the water heater. The water heater is equipped
with 3/4” NPT water connections.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
The temperature-pressure relief valve must be installed
directly into the fitting of the water heater designed for the
relief valve. Must terminate a maximum of 6 in. (15cm)
above a floor drain or external to the building. In cold
climates, it is recommended that the discharge pipe be
terminated at an adequate drain inside the building. Be
certain that no contact is made with any live electrical part.
The discharge opening must not be blocked or reduced
in size under any circumstances. Excessive length, over
30 ft. (9.14m), or use of more than four elbows can cause
restriction and reduce the discharge capacity of the valve
(see Figures 3 & 19).
The temperature-pressure relief valve must be manually
operated at least once a year, (see Figure 17). Caution
should be taken to ensure that (1) no one is in front of or
around the outlet of the temperature-pressure relief valve
discharge line, and (2) the water manually discharged will
not cause any bodily injury or property damage because
the water may be extremely hot.
No valve or other obstruction is to be placed between the
relief valve and the tank. Do not connect tubing directly to
discharge drain unless a 6 in. (15cm) air gap is provided.
To prevent bodily injury, hazard to life, or property damage,
the relief valve must be allowed to discharge water in
quantities should circumstances demand. If the discharge
pipe is not connected to a drain or other suitable means,
the water flow may cause property damage.
FIGURE 17
If after manually operating the valve, it fails to completely
reset and continues to release water, immediately close
the cold water inlet to the water heater, follow the draining
instructions, and replace the temperature-pressure relief
valve with a new one.
T&P Valve and Pipe Insulation (if supplied)
Remove insulation for T&P valve and pipe connections
from carton.
The Discharge Pipe:
•
Shall not be smaller in size than the outlet pipe size
of the valve, or have any reducing couplings or other
restrictions.
•
•
•
Shall not be plugged or blocked.
Shall be of material listed for hot water distribution.
Shall be installed so as to allow complete drainage of
both the temperature-pressure relief valve, and the
discharge pipe.
•
•
Shall terminate a maximum of 6 in. (15cm) above a floor
drain or external to the building. In cold climates, it is
recommended that the discharge line be terminated at
an adequate drain inside the building.
Shall not have any valve between the relief valve and
tank.
FIGURE 18
Fit pipe insulation over the incoming cold water line and
the hot water line. Make sure that the insulation is against
the top cover of the heater. Fit T&P valve insulation over
valve. Make sure that the insulation does not interfere with
the lever of the T&P valve.
Secure all insulation using tape.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
GAS PIPING
Use pipe joint compound or Teflon tape marked as being
resistant to the action of petroleum [Propane (L.P.)]
gases.
Make sure gas supplied is same type listed on model
rating plate. The inlet gas pressure must not exceed 14
in. WC (3.5 kPa) for natural and propane gas (L.P.). The
minimum inlet gas pressure shown on rating plate is that
which will permit firing at rated input.
The appliance and its gas connection must be leak tested
before placing the appliance in operation.
The appliance and its individual shut-off valve must be
disconnected from the gas supply piping system during
any pressure testing of the system at test pressures in
excess of 1/2 psi (3.5 kPa).
All gas piping must comply with local codes and ordinances
or with the National Fuel Gas Code (ANSI Z223.1/ NFPA-
54). Copper or brass tubing and fittings (except tin lined
copper tubing) should not be used.
It shall be isolated from the gas supply piping system
by closing its individual manual shut-off valve during
the pressure testing, the gas supply piping system at
test pressures equal to or less than 1/2 psi (3.5 kPa) is
considered isolated.
If the gas control valve is subjected to pressures exceeding
1/2 psi (3.5 kPa), the damage to the gas control valve could
result in a fire or explosion from leaking gas.
If the main gas line shut-off serving all gas appliances is
used, also turn “off” the gas at each appliance. Leave all
gas appliances shut “off” until the water heater installation
is complete.
IMPORTANT:MAKESURETHEGASLINEISPIPEDWITH
HARD PIPE. AVOID FLEX LINE CONSTRUCTION FOR
GAS DUE TO POSSIBLE GAS FLOW PROBLEMS.
Agas line of sufficient size must be run to the water heater.
Consult the current edition of National Fuel Gas Code
(ANSI Z223.1/NFPA54) and your gas supplier concerning
pipe size.
SEDIMENT TRAPS
There must be:
•
A readily accessible manual shut off valve in the gas
supply line serving the water heater, and
Adrip leg (sediment trap) ahead of the gas control valve
to help prevent dirt and foreign materials from entering
the gas control valve.
•
•
Aflexible gas connector or a ground joint union between
the shut off valve and control valve to permit servicing
of the unit.
The appliance and its gas connections must be leak tested
before placing the appliance in operation. Use a leak test
solution, not a match or open flame.
A sediment trap shall be installed as close to the gas inlet
of the water heater as practical at the time of water heater
installation. The sediment trap shall be either a tee fitting
with a capped nipple in the bottom outlet or other device
recognized as an effective sediment trap.
NOTE: An alternate location for the gas line entry is
possible. Drill a suitable hole centered on the crosshairs
on the left side panel.
Contaminants in the gas lines may cause improper
operation of the gas control valve that may result in fire
or explosion. Before attaching the gas line be sure that all
gas pipe is clean on the inside. To trap any dirt or foreign
material in the gas supply line, a drip leg (sometimes called
Download from Www.Somanuals.com. All Manuals Search And Download.
21
a sediment trap) must be incorporated in the piping. The
drip leg must be readily accessible. Install in accordance
with the “Gas Piping” section. Refer to the current edition
of the National Fuel Gas Code (ANSI Z223.1/NFPA 54).
FLOODING/FREEZING
If this water heater has been exposed to flooding,
freezing, fire or any unusual condition, do not put it into
operation until it has been inspected and approved by a
qualified service technician. These conditions can result
in unseen internal damage and are not subject to warranty
coverage.
GAS LINE PURGING
Air may be present in the gas lines and could prevent
the burner from lighting on initial start-up. The gas lines
should be purged of air by a qualified service technician
after installation of the gas piping system.
FILLING THE WATER HEATER
HIGH ALTITUDE INSTALLATIONS
Never use this water heater unless it is completely full of
water. To prevent damage to the tank, the tank must be
filled with water. Open the nearest hot water faucet to allow
air to escape. Water must flow from the hot water faucet
before turning “ON” gas to the water heater.
To fill the water heater with water:
1. Close the water heater drain valve by turning the
handle to the right (clockwise). The drain valve is on
the lower front of the water heater.
2. Openthecoldwatersupplyvalvetothewaterheatertank.
NOTE: The cold water supply valve must be left
open when the water heater is in use.
3. To insure complete filling of the tank, allow air to exit
by opening the nearest hot water faucet. Allow water
to run until a constant flow is obtained. This will let air
out of the water heater and the piping.
4. Check all water piping and connections for leaks.
Repair as needed.
The heater is set at the factory to operate at altitudes from
sea level to 3,500 ft. (1,067m).Accessory kits are available
to allow the heater to operate at altitudes higher than 3,500
ft. (1,067m). These accessory kits are listed in the table
below. Instructions for installing these accessories are
included in the kits.
VENTING
Altitude ft (m)
Kit #
3,501 - 6,500 (1,067 -1,981)
6,501 - 8,500 (1,981 - 2,591)
8,501 - 11,000 (2,591 - 3,352)
9007439005
9007440005
9007441005
Rated inputs are suitable up to 11,000 ft. (3,352m)
elevation. Consult the factory for installation at altitudes
over 11,000 ft. (3,352m).
WARNING: THIS HIGH EFFICIENCY WATER HEATER
IS CERTIFIED FOR USE AT AN ALTITUDE OF 11,000
Ft. (3,352 METERS). HOWEVER, FOR USE AT
ALTITUDES OVER 3,500 Ft. (1,067m) THE PCB MUST
BE CHANGED.
Some gas utility companies derate their gas for altitude,
making it unnecessary to modify the water heater for high
altitude installations. Call the local gas or utility company
to verify BTU content.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
VENT PIPE TERMINATION
Instructions on proper installation through a sidewall are
provided in Figures 31.
Plan the vent system layout so that proper clearances are
maintained from plumbing and wiring.
NOT RECOMMENDED:
PREFERRED PRACTICE:
Vent pipes serving power vented appliances are classified
by building codes as “vent connectors”. Required
clearances from combustible materials must be provided in
accordance with information in this manual under FACTS
TO CONSIDER ABOUT LOCATION AND INSTALLING
THE WATER HEATER, and with the National Fuel Gas
Code and local codes.
STREET ELBOW
NORMAL ELBOW
PLANNING THE VENT SYSTEM
6 in.
(15 cm) min.
Plan the route of the vent system from the exhaust elbow
to the planned location of the vent terminal.
1. Layout total vent system to use a minimum of vent pipe
and elbows.
BACK TO BACK ELBOWS
2. This water heater is capable of venting flue gases a
maximum distance equivalent to 50 ft. (15.2m) of 2 in.
pipe or 100 ft. (30.5m) of 3 in. pipe. The use of elbows
reduces the maximum distance (see Table 1).
NOTE: The lengths of pipe listed are exclusive of the
termination. The termination elbow, with an installed
screen, is required and uses the equivalent of 7 ft.
(2.1m) of vent pipe length. Therefore, the remainder of
the vent system must not exceed the lengths listed.
NOTE: Do NOT use Cellcore venting (PVC outer layer,
foamcore-type material for middle layer, and then PVC
inside layer).
Maximum vent
length for 2 in. pipe length for 3 in. pipe
ft. (m) ft. (m)
Short Short
Maximum vent
Number
of 90°
Elbows
90° SHORT SWEEP ELBOW
(MORE RESTRICTIVE)
90° LONG SWEEP ELBOW
(LESS RESTRICTIVE)
Long
Radius
Elbow
Long
Radius
Elbow
FIGURE 19
Radius
Elbow
Radius
Elbow
1
2
3
4
5
43 (13.1) 45 (13.7) 93 (28.4) 95 (28.9)
36 (10.9) 40 (12.2) 86 (26.2) 90 (27.4)
29 (8.8) 35 (10.6) 79 (24.0) 85 (25.9)
22 (6.7) 30 (9.1) 72 (21.9) 80 (24.4)
15 (4.5) 25 (7.6) 65 (19.8) 75 (22.8)
TABLE 1
VENT LENGTH LESS THAN OR
VENT LENGTH GREATER THAN 20
EQUAL TO 20 EQUIVALENT FEET EQUIVALENT FEET (6.1m) USE THIS
(6.1m) USE THIS SCREEN. SCREEN.
3. The exhaust elbow assembly comes with a straight
section of 2 in. pipe installed. To continue the vent
system, a rubber coupling must be attached. The
venting must extend 6 in. (15cm) vertically from the
top of the heater before installing an elbow.
FIGURE 20
The first step is to determine where the vent pipe will
terminate (see Figures 24, 29 & 31). The vent may
terminate through a sidewall as shown in Figure 24 or
through the roof as shown in Figure 29.
If using 2 inch vent pipe:
Install the rubber coupling and gear clamps (supplied)
at the end of the section of vent pipe installed on the
heater. Continue building the vent system, or connect
the existing vent system to the coupling. The total
vent system must not exceed the lengths discussed
above, where each (short radius) elbow is equal to 7
equivalent feet (2.1m) of straight pipe. The elbow and
rodent screen supplied in the vent kit must be used as
the vent termination.
The vent system must terminate so that proper clearances
are maintained as cited in local codes or the current edition
of the National Fuel Gas Code, (ANSI Z223.1, 12.9.1
through 12.9.4).
Download from Www.Somanuals.com. All Manuals Search And Download.
23
NOTE: VENT PIPE MUST BE SUPPORTED EVERY 4 ft. (1.2m). TO PREVENT VIBRATION, USE
ISOLATION PADS WHEN ATTACHING STRAPS TO FLOOR JOISTS, WALLS OR CEILINGS.
TERMINATION
ELBOW
45°
ELBOW
STRAP
90°
ELBOW
RODENT SCREEN
(INSTALL INTO
ELBOW)
Example for calculating equivalent feet.
Section “A” . . . . 0.5 ft. . . (0.15m)
90° elbow . . . . . 7.0 ft. . . (2.13m)
Section B . . . . . 1.0 ft. . . (0.31m)
45° elbow . . . . . 4.0 ft. . . (1.21m)
Section C . . . . . 1.5 ft. . . (0.46m)
45° elbow . . . . . 4.0 ft. . . (1.21m)
Section D . . . . . 15.0 ft. . (4.57m)
Total Equivalent 33.0 ft. . (10.04m)
Based on this example use the (fully open) rodent
screen for vent length greater than 20 equivalent
ft. (6.1 equivalent metres).
Vent piping must slope up
from heater to termination a
minimum of 1/8 in. (0.3cm)
rise per 4 ft. (1.2m) of vent
piping
6 in.
(15cm)
MIN.
GROUND LEVEL OR
MAXIMUM SNOW
LINE*
FIGURE 21
If using 3 inch vent pipe:
If the water heater is being installed as a replacement
for an existing power vented heater in pre-existing
venting, a thorough inspection of existing venting
system must be performed prior to any installation work.
Verify that correct material as detailed above has been
used, and that the minimum or maximum vent lengths
and terminal location as detailed in this manual have
been met. Carefully inspect the entire venting system
for any signs of cracks or fractures, particularly at joints
between elbows and other fittings and straight runs of
vent pipe. Check system for signs of sagging or other
stresses in joints as a result of misalignment of any
components in the system. If any of these conditions
are found, they must be corrected in accordance
with the venting instructions in this manual before
completing installation and putting the water heater
into service.
Install the rubber reducing coupling (2 in. to 3 in.) and
gear clamps (supplied) at the end of the section of
vent pipe installed on the heater. Continue building
the vent system, or connect the existing vent system
to the coupling. The total system must not exceed
the equivalent pipe lengths discussed above where
each (long radius) elbow is equal to 5 ft. (1.5m) of 3
in. diameter straight vent pipe. The elbow and rodent
screen supplied in the vent kit must be used as the vent
termination.
NOTE: This unit can be vented with PVC pipe materials
(DWV ASTM-D2665; Schedule 40, 80, 120 ASTM-
D1785; or SDR Series ASTM-D2241), CPVC pipe
materials (CPVC41 ASTM-D2846; Schedule 40, 80
ASTM-F441; or SDR Series ASTM-F442), ABS pipe
materials (Schedule 40 DWV ASTM-D2661). The
fittings, other than the TERMINATION should be
equivalent to PVC-DWV fittings meetingASTM D-2665
(Use CPVC fittings, ASTM F-438 for CPVC pipe and
ABS fittings,ASTM D-2661/3311 forABS pipe). If CPVC
or ABS pipe and fittings are used, then proper cement
must be used for all joints, including joining the pipe to
Termination (PVC Material). If local codes do not allow
the use of the PVC termination when a material other
than PVC is used for venting, then an equivalent fitting
of that material may be substituted if the screen in the
PVC terminal is removed and inserted into the new
fitting.
NOTE: (A.) For water heaters in locations with high
ambient temperatures (above 100°F (38°C)) it is
recommended that CPVC or ABS pipe and fittings be
used. (B.) A 22.5 degree elbow (2 in. vent pipe) or a 45
degree elbow (3 in. vent pipe) with an installed screen
VENT TERMINAL must be used in all cases.
4. There will be some installations where condensate will
be formed in the horizontal runs of the vent system.
This condensate will run into the condensate trap. The
water heater is shipped with a condensate tube that
attaches to the condensate trap. No other tee or fitting
is required.
This water heater is supplied with a 45 degree
termination elbow that is a special fitting that must be
used with the appliance.
PVC Materials should use ASTM D-2564 Grade
Cement; CPVC Materials should use ASTM F-493
Grade Cement and ABS Materials should use ASTM
D-2235 Grade Cement.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDENSATE
VENTING
EXHAUST
ELBOW
This water heater is a condensing unit and requires a drain
to be located in close proximity to allow the condensate
to drain safely. The condensate drains from the unit at
the exhaust tee located at the bottom of the unit (see
Figure 22). Condensate from this water heater is mildly
acidic. Please note that some local codes require that
condensate is treated by using a pH neutralizing filter
prior to disposal.
BARBED FITTING
CONDENSATE
TRAP
DRAIN PAN - ROUTE
TO SUITABLE DRAIN
Caution must be used to ensure that the drain is free and
clear of debris and will not allow backflow through the
condensate tube. Consideration must be given to avoid
freezing of the condensate lines which could result in
excessive build up of condensate inside the water heater.
Waterproof heat tape may be required to prevent freezing
of the condensate lines. Please ensure that the outlet of
the condensate drain does not create a slippery condition
which could lead to personal injury.
CONDENSATE TUBE -
SLOPE TO SUITABLE DRAIN
NOTE: THE CONDENSATE TUBE
MUST BE BELOW EXHAUST ELBOW.
FIGURE 22
To operate properly and prevent exhaust gases from
escaping through the condensate trap, the trap must
contain some water. Before being started for the first time,
water must be added to the trap. Remove the condensate
tube (if installed) and add water to the trap through the
hole for the condensate tube until it flows from the hole.
(Re)install the condensate tube.
INSTALLATION OF VENT SYSTEM
Before beginning installation of piping system thoroughly
read the “Vent Pipe Preparation” section of this manual.
If you are installing your system so that it vents through
roof, please refer to the section titled “Installation Of
Vertical Vent System”.
CONDENSATION WARNING:
THIS WATER HEATER IS A CONDENSING UNIT AND
REQUIRES A DRAIN TO BE LOCATED IN CLOSE
PROXIMITY TO ALLOW CONDENSATE TO DRAIN
SAFELY. THE CONDENSATE DRAINS FROM UNIT AT
THE EXHAUST ELBOW LOCATED AT BOTTOM OF
UNIT.
Ensure the vent length is long enough that the outside air
will not cause the water heater to freeze.
VENT TERMINAL INSTALLATION, SIDEWALL
1. Install the vent terminal by using the cover plate as
a template to mark the hole for the vent pipe to pass
through the wall. BEWARE OF CONCEALED WIRING
AND PIPING INSIDE THE WALL.
2. If the Vent Terminal is being installed on the outside
of a finished wall, it may be easier to mark both the
inside and outside wall. Align the holes by drilling
a hole through the center of the template from the
inside through to the outside. The template can now
be positioned on the outside wall using the drilled hole
as a centering point for the template.
NOTE: IT IS IMPORTANT THAT THE CONDENSATE
TUBE NOT BE ELEVATED ABOVE THE CONDENSATE
TRAP OUTLET (SEE FIGURE 22). CONDENSATE
BUILD-UP WILL BLOCK THE EXHAUST OUTLET,
WHICH WILL CAUSE IMPROPER OPERATION. WITH
SOME INSTALLATIONS IT IS RECOMMEND TO
INSTALL A CONDENSATE PUMP.
NOTE: Barbed fitting not required if hard piping is used
to drain condensate.
3. A) MASONRY SIDE WALLS
Chisel an opening approximately 1/2 in. (1.3cm)
larger than the marked circle.
B) WOODEN SIDE WALLS
Drill a pilot hole approximately 1/4 in. (0.64cm)
outside of the marked circle. This pilot hole is used
as a starting point for a saws-all or sabre saw blade.
Cut around the marked circle staying approximately
1/4 in. (0.64cm) outside of the line. (This will allow
the vent to easily slide through the opening. The
resulting gap will be covered up by the Vent Terminal
cover plate.) Repeat this step on inside wall if
necessary.
Download from Www.Somanuals.com. All Manuals Search And Download.
25
SEQUENCE OF INSTALLATIONS
B. WOODEN SIDE WALLS Drill a pilot hole
approximately 1/4 in. (0.64cm) outside of the marked
circle. This pilot hole is used as a starting point for a
saws-all or sabre saw blade. Cut around the marked
circle staying approximately 1/4 in (0.64cm) outside
of the line. (This will allow the vent pipe to easily
slide through the opening. The resulting gap will be
covered by the vent terminal cover plates.) Repeat
this step on the inside wall if necessary.
Cut a length of PVC pipe about 3.5 in. (9cm) longer than
the wall thickness at the opening. Glue the vent terminal
to this section of pipe. Slide the wall plate over the pipe to
stop against the vent terminal. Place a bead of caulking
(not supplied) around the gap between the pipe and cover
plate. Apply enough to fill some of the gap between the
pipe and wall. Place some of the caulking on the back
of the plate to hold it against the wall after installation. If
the vent pipe is installed up to the wall, with a coupling
on the end against the wall opening, the pipe with the
vent terminal can be prepared for gluing before inserting
through the wall. Slide the pipe through the wall and insert
into the coupling on the other side of the wall, making
sure that the vent terminal ends up pointed in the correct
position (see Figure 23).
2. Cut a length of 3 in. PVC pipe about 3.5 in. (9cm) longer
than the wall thickness at the opening.
3. Glue the intake vent terminal to the section of the
pipe.
4. Slide the wall plate over pipe to stop against intake vent
terminal.
5. Place a bead of caulking (not supplied) around the
gap between the pipe and the wall. Place some of the
caulking on the back of the plate to hold it against the
wall after installation.
6. If the vent pipe is installed up to the wall, with a coupling
on the end against the wall opening, the pipe with
the vent terminal can be prepared for gluing before
inserting through the wall. Slide the pipe through the
wall and insert into coupling on the other side of the
wall, making sure that the vent terminal ends up pointed
in the correct position (see Figure 24).
FIGURE 23
INSTALLATION SEQUENCE
For installations in the City of Los Angeles, California
Category IV PVC Pipe such as that manufactured by
Brownline Pipe Company, must be used as vent pipe
material.
CAUTION
Vent terminals supplied with heater must be used.
FIGURE 24
NOTE: BEFORE BEGINNING INSTALLATION OF ANY
VENT PIPE READ THE VENT PIPE MANUFACTURER’S
INSTALLATION INSTRUCTIONS.
1. After the points of termination have been determined,
use the cover plates as templates to mark the holes for
the vent pipes to be inserted through the wall. BEWARE
OF CONCEALED WIRING AND PIPING INSIDE OF
WALL. If the vent terminals are being installed on the
outside of a finished wall, it may be easier to mark both
the inside and outside wall. Align the holes by drilling
a hole through the center of the template from the
inside through to the outside. The template can now
be positioned on the outside wall using the drilled holes
as a centering point for the template.
A. MASONRY SIDE WALLS Chisel an opening
approximately 1/2 in. (1.3cm) larger than the marked
circle.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACH 45°
TERMINATION
ELBOW
BRACKET
6 in. (15 cm)
MIN. LENGTH
SEALANT
ATTACH 45°
TERMINATION
ELBOW
RODENT
SCREEN
(INSTALL
INTO
EQUIVALENT
VENT LENGTH
MEASURED
FROM THIS
POSITION
VENT PIPING TO BE
SLOPED (DOWN)
TOWARD HEATER
TO PREVENT WATER
FROM COLLECTING.
RODENT
SCREEN
(INSTALL
INTO
ELBOW)
SEALANT
12 in.
(30 cm) min.
12 in.
VENT
RISER
SEALANT
(30 cm) min.
ELBOW)
GROUND
LEVEL*
GROUND
LEVEL*
VENT
PIPING TO
BE SLOPED
(DOWN)
SEALANT
TOWARD
HEATER TO
*WHERESNOWCOVERISNORMALDURINGWINTER, ENSURESUFFICIENT
VENT CLEARANCE TO PREVENT BLOCKAGE OR ICE BUILDUP.
* WHERE SNOW COVER IS NORMAL DURING WINTER, PREVENT
ENSURE SUFFICIENT VENT CLEARANCE TO PREVENT WATER FROM
BLOCKAGE OR ICE BUILDUP.
COLLECTING.
FIGURE 25
FIGURE 27
INSTALLATION OF VENT SYSTEM, SIDEWALL
Before completing the installation of the venting system
be sure to read the sections of this manual discussing the
proper method of cutting and cementing PVC pipe and
fittings in the “Vent Pipe Preparation” section.
With the route of the venting system and selection of
materials completed, as discussed in the section of this
manual titled “Planning The Vent System”, the through the
wall vent terminal in place and the first section of piping,
up to first elbow, installed at the rubber coupling, it is time
to complete the installation of the venting system for the
sidewall installation.
It is recommended that the completion of the venting
system start at the rubber coupling and run to the coupling
on the inside wall of the vent terminal (see Figure 23).
The vent system piping should be supported every
5 ft. (1.5m) of vertical run and every 3 ft. (91cm) of
horizontal run. All piping and fittings must be joined by
the proper procedures as described under: VENT PIPE
PREPARATION.
INSTALLATION OF VERTICAL VENT SYSTEM
A proper flashing or “BOOT” should be used to seal the
pipe where it exits the roof. The total vent system should
not exceed the equivalent feet of pipe as listed in Table
1.
Provide support for all pipe protruding through the roof.All
piping should be properly secured. The vent system piping
should be supported every 5 ft. (1.5m) of vertical run and
every 3 ft. (91cm) of horizontal run. All piping and fittings
must be joined by the proper procedures as described
under: VENT PIPE PREPARATION.
FIGURE 26
Download from Www.Somanuals.com. All Manuals Search And Download.
27
VENT PIPE PREPARATION
1. INITIAL PREPARATION.
A. Make sure the solvent cement you are planning to
use is designed for the specific application you are
attempting.
B. Know the physical and chemical characteristics and
limitations of the PVC and CPVC piping materials
that you are about to use.
C. Know the reputation of your manufacturer and their
products.
D. Know your own qualifications or those of your
contractor. The solvent welding technique of joining
PVC and CPVC pipe is a specialized skill just as any
other pipe fitting technique.
E. Closely supervise the installation and inspect the
finished job before start-up.
F. Contact the manufacturer, supplier, or competent
consulting agency if you have any questions about
the application or installation of PVC and CPVC
pipe.
G. Take the time and effort to do a professional job.
Shortcuts will only cause you problems and delays
in start-up. By far, the majority of failures in PVC and
CPVC systems are the result of shortcuts and/or
improper joining techniques.
FIGURE 28
2. SELECTION OF MATERIALS.
•
•
Cutting Device - Saw or Pipe Cutter.
Deburring Tool, Knife, File, or Beveling Machine (2
in. and above).
Brush - Pure Bristle.
Rag - Cotton (Not Synthetic).
Primer and Cleaner.
Solvent Cement - PVC for PVC Components and
CPVC for CPVC Components.
Containers - Metal or Glass to hold Primer and
Cement. Select the type of PVC or CPVC materials
to be used on the basis of their application with
respect to chemical resistance, pressure rating,
temperature characteristics, etc.
3 in. (7.6cm)
MIN. LENGTH
TERMINATION
MAY BE 45°
ELBOW OR A
“T” ELBOW
•
•
•
•
RODENT
SCREEN
(INSTALL
INTO
A VENT USED IN A SPECIAL
VENTINGSYSTEMWITHPOSITIVE
VENT PRESSURE AND PASSING
18 in.
(45cm)
•
THROUGH
A
ROOF SHALL
ELBOW)
EXTEND AT LEAST 450mm (18
in.) ABOVE THE HIGHEST POINT
WHERE IT PASSES THROUGH
THE ROOF SURFACE AND ANY
OTHER OBSTRUCTION WITHIN
A HORIZONTAL DISTANCE OF
450mm (18 in.). A VERTICAL
VENTING SYSTEM MUST BE
SUPPORTED EVERY 1.5m (5 ft.).
ROOF
LINE
•
Insertion Tool - Helpful for larger diameter pipe and
fittings 6 in. (15cm) and above.
FIGURE 29
IMPORTANT
The vent system must terminate so that proper clearances
are maintained as cited in local codes or the current
edition of the National Fuel Gas Code (ANSI Z223.1) and
as listed below:
1. Vent Termination must extend a minimum of 18
in. (46cm) above roof or 18 in. (46cm) above the
anticipated snow level to prevent blockage of the vent
termination, as shown in Figures 28 and 29.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
*USE ONLY NATURAL BRISTLE
3. MAKING THE JOINT.
A. Cutting
Pipe must be squarely cut to allow for the proper
interfacing of the pipe end and the fitting socket
bottom. This can be accomplished with a miter box
saw or wheel type cutter Wheel type cutters are not
generally recommended for larger diameters since
they tend to flare the corner of the pipe end. If this
type of cutter is used, the flare on the end must be
completely removed.
NOTE: Power saws should be specifically designed to
cut plastic pipe.
PRIMER
It is recommended that Tetrahydrofuran (THF) be used
to prepare the surfaces of pipe and fittings for solvent
welding. Do not use water, rags, gasoline or any other
substitutes for cleaning PVC or CPVC surfaces.Achemical
cleaner such as MEK may be used.
STEP A
CEMENT
The cement should be a bodied cement of approximately
500 to 1600 centipoise viscosity containing 10-20% (by
weight) virgin PVC material solvated with tetrahydrofuran
(THF). Small quantities of dimethyl formamide (DMF)
may be included to act as a retarding agent to extend
curing time. Select the proper cement; Schedule 40
cement should be used for Schedule 40 pipe. Never use
all-purpose cements, commercial glues and adhesives or
ABS cement to join PVC or CPVC pipe and fittings.
B. Deburring
Use a knife, plastic pipe deburring tool, or file to
remove burrs from the end of small diameter pipe.
Be sure to remove all burrs from around the inside
as well as the outside of the pipe. A slight chamfer
(bevel) of about 10°-15° should be added to the end
to permit easier insertion of the pipe into the end of
the fitting. Failure to chamfer the edge of the pipe
may remove cement from the fitting socket, causing
the joint to leak.
APPLICATORS
Select a suitable pure bristle type paint brush. Use a proper
width brush or roller to apply the primer and cement (see
chart below). Speedy application of cement is important
due to its fast drying characteristics. IMPORTANT NOTE:
Adauber type applicator should only be used on pipe sizes
2 in. and below. For larger diameter pipe, a brush or roller
must be used.
STEP B
C. Test dry fit of the joint
Tapered fitting sockets are designed so that
an interfaced fit should occur when the pipe is
inserted about 1/3 to 2/3 of the way into the socket.
Occasionally, when pipe fitting dimensions are at
the tolerance extremes, it will be possible to fully
insert dry pipe to the bottom of the fitting socket.
When this happens, a sufficient quantity of cement
must be applied to the joint to fill the gap between
the pipe and fitting. The gap must be filled to obtain
a strong, leak-free joint.
RECOMMENDED BRUSH* SIZE FOR PRIMER AND
CEMENT APPLICATIONS
Nominal Pipe (IPS)
Size Brush Width
1.5 in. (3.8cm)
2
3
1.5”-2.5 in. (3.8cm -
6.4cm)
Download from Www.Somanuals.com. All Manuals Search And Download.
29
D. Inspection, cleaning, priming
Remove all excess cement from around the pipe
and fitting with a dry cotton rag. This must be done
while the cement is still soft.
Visually inspect the inside of the pipe and fitting
sockets and remove all dirt, grease or moisture
with a clean dry rag. If wiping fails to clean the
surfaces, a chemical cleaner must be used. Check
for possible damage such as splits or cracks and
replace if necessary.
The joint should not be disturbed immediately after
the cementing procedure, and sufficient time should
be allowed for proper curing of the joint. Exact drying
time is difficult to predict because it depends on
variables such as temperature, humidity and cement
integrity. For more specific information, you should
contact your solvent cement manufacturer.
Depth-of-entry
Marking the depth of entry is a way to check if the
pipe has reached the bottom of the fitting socket
in Step F. Measure the fitting depth and mark this
distance on the pipe O.D. You may want to add
several inches to the distance and make a second
mark as the primer and cement will most likely
destroy your first one.
Apply primer to the surface of the pipe and fitting
socket with a natural bristle brush. This process
softens and prepares the PVC or CPVC for the
solvent cementing step. Move quickly and without
hesitation to the cementing procedure while the
surfaces are still wet with primer.
STEP G
CONNECTION TO VENT PIPE
E. Application of solvent cement
•
Apply the solvent cement evenly and quickly around
the outside of the pipe at a width a little greater than
the depth of the fitting socket.
Apply a light coat of cement evenly around the inside
of the fitting socket. Avoid puddling.
The vent system connects to the vent pipe with and elbow
or rubber coupling. This coupling includes gear clamps.
These connections must be properly seated and tightened
to prevent the leakage of flue gases into the installation
area.
•
•
Apply a second coat of cement to the pipe end.
With 2 in. venting the straight rubber adapter is used for the
connection to the vent pipe. With 3 in. venting a transition
adapter is required to change from the 2 in. vent pipe to
the 3 in. vent size.
Clean and lightly sand the end of the vent piping that will
connect to the rubber coupling.
Loosen the upper clamp on the rubber adapter and insert
the sanded end of the vent pipe and tighten the gear
clamp.
STEP E
F. Joint assembly
NOTE: Do not glue or seal in the rubber coupling. Check
the venting system to ensure that there is no stress on the
connection or the vent pipe which will create a twisting or
bending.
Working quickly, insert the pipe into the fitting socket
bottom and give the pipe or fitting a 1/4 turn to evenly
distribute the cement. Do not continue to rotate the
pipe after it has hit the bottom of the fitting socket.
A good joint will have sufficient cement to make a
bead all the way around the outside of the fitting hub.
The fitting will have a tendency to slide back while
the cement is still wet so hold the joint together for
about 15 seconds.
UPPER GEAR
CLAMP
LOWER
GEAR CLAMP
RUBBER COUPLING/
ADAPTER (2”)
RUBBER ADAPTER (2 in.to
3”)
FIGURE 30
STEP F
G. Cleanup and joint movement
U.S. POWER VENT
30
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
VENT HOOD(S) MAY BE
EXTREMELY HOT
DURING OPERATION.
FIGURE 31
CAUTION
TO PREVENT EXHAUSTING PRODUCTS FROM CIRCULATING TO THE AIR INTAKE IN
WINDY/COLD AREAS, THE MAXIMUM PRACTICAL DISTANCE BETWEEN THESE TWO
TERMINALS IS RECOMMENDED.
Download from Www.Somanuals.com. All Manuals Search And Download.
31
ELECTRICAL CONNECTIONS
To put the heater into service after a successful
calibration:
The water heater must be connected to a properly
grounded electrical branch circuit. A dedicated circuit is
preferred. Do not use a GFI outlet.
1. Unplug the power cord from the 120Vac/60Hz outlet
2. Open (plastic) front door of the heater and remove the
cover of the heat engine. The DIP switches are located
on the PCB which is mounted on the right-hand side
of the heat engine.
Refer to the rating plate attached to the water heater to
determine the electrical requirements for the heater. Ensure
the circuit provided is correct for these requirements.
3. Set DIP switch 4 in the normal (OFF or “up”) position
(see Figure 33a).
4. Reinstall the front cover of the heat engine, close and
latch the front door of the heater.
Important: Do not use an extension cord to connect the
water heater to an electrical outlet.
5. Plug the power cord into the 120Vac/60Hz outlet.
6. Press the Standby Button to turn on the heater and
start the unit.
Important: The electrical controls used inside the gas
control of this water heater are polarity sensitive. Ensure
the electrical supply is connected correctly in the receptacle
box. Failure to connect correctly will prevent the unit from
functioning properly.
When all the water, gas and venting connections have
been correctly made, fill the tank as directed in the section
“FILLING THE WATER HEATER”.
DIP Switch 4 in
normal mode
(“OFF”, “up”)
DIP Switch 4 in
calibration mode
(“ON”, “down”)
FIGURE 33a
When the tank has been filled, connect the electrical power
and proceed with starting the water heater as directed in
the “CALIBRATION” section.
The E36 “calibration error” occurs in the following
situations:
•
•
•
Calibration switch (DIP switch 4) is in the calibrate (ON
or “down”) position and an “end call-for-heat” occurs
before the Calibration Procedure is finished.
Calibration switch (DIP switch 4) is in the calibrate (ON
or “down”) position there is no “call-for-heat” within 6
minutes of turning on the power.
Calibration switch (DIP switch 4) is in the calibrate (ON
or “down”) position and the unit is calibrated but the DIP
switch is not set to the normal (OFF or “up”) within 6
minutes after the Calibration Procedure is finished.
Calibration switch (DIP switch 4) is in the normal (OFF
or “up”) position and the unit is not calibrated and 1
minute (or more) passes after turning on the power.
CALIBRATION
The water heater must be calibrated as follows before
being put into service. The Calibration Procedure
examines and measures certain details of your installation
and automatically sets some control parameters. Before
starting the Calibration Procedure, the heater must be
properly installed and connected to the water piping and
the vent system. Ensure all panels, covers and doors are
in place. To avoid a possible “end of call-for-heat” (and
consequent interruption of the Calibration Procedure), a
continuous water draw from the heater is recommended
during the calibration.
•
If an E36 error message is displayed:
1. Unplug the power cord from 120Vac/60Hz outlet.
2. Open front door of the heater and remove the front
cover of the heat engine.
This procedure assumes that the heater is installed with
DIP switch 4 in the calibration (ON or “down”) position
(see Figure 33a).
3. Check that (or set) DIP switch 4 is in the calibrate (ON
or “down”) position.
4. Generate a 5 minute (minimum) water draw from the
heater.
To calibrate the heater:
1. Plug the power cord into a 120Vac/60Hz outlet.
2. Press the Standby Button to turn on the heater and
initiate the Calibration Procedure.
3. The Calibration Procedure will last about 6 minutes. Do
not interrupt this procedure once it has started.After a
successful calibration the heater will go into standby
mode. During the calibration if the “call-for-heat” ends,
the calibration was not completed and the E36 error
message will be shown on the display. If this occurs,
unplug the power cord and repeat steps 1 and 2.
5. Repeat the calibration procedure.
NOTE: If changes are made to the vent system or the
heater is re-located, the Calibration Procedure must be
repeated.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
DISPLAY PANEL
STANDBY LED
(GREEN)
TEMPERATURE
UNITS-OF-MEASURE
STANDBY-ON/OFF
NUMERIC
DISPLAY
UP (HOTTER)
BUTTON
BUTTON
MODE BUTTON
BURNER IN
OPERATION
KEY LOCK
MODE LEDs (3)
DOWN (COLDER)
BUTTON
FAULT INDICATOR
FIGURE 33
Changing the Standby Status
Operating Modes
When the Standby Button is pressed, the Status changes
to normal operation and all the LEDs on the display will
light up for a period of 1 second to verify operation. The
button can toggle the status between Normal operation
and Standby.
Operating modes are:
Boost (for peak demand), Energy Saver and Vacation.
Three LEDs are used to indicate the Operating Mode.
Vacation Mode:
Energy Saver Mode: Green LED
Boost Mode: Orange LED
Yellow LED
Key Lock
The Operating Modes have the following characteristics:
Vacation mode:
NOTE: This is a tamper resistant feature.
The Key Lock is considered “On” or “Off”:
•
•
•
Fixed temperature setting of 90°F (32°C)
Set-point Difference is 14°F (8°C)
Tank Set-point Differential is 22°F (12°C)
•
Key Lock is turned “On” after one minute without a key
press by the user.
•
Key Lock can then be turned “Off” for one minute
by simultaneously pressing the “Up” Button and the
“Down” Button for three seconds.
Energy Saver mode:
•
Temperature range from 100°F to 135°F (38°C to 57°C)
in increments of 1°F or 1°C
When the keys are locked, the Temperature Set-point
cannot be increased and the Operating Mode cannot be
changed. The set-point may be decreased while the keys
are locked.
•
•
Set-point Difference is 14°F (8°C)
Tank Set-point Differential is 14°F (8°C)
Boost mode:
•
Temperature ranges from 140°F to 158°F (60°C to
70°C) in increments of 1°F or 1°C
The On/Off Button is not affected by the Key Lock feature.
All other buttons are “locked” when the Key Lock is
“On”.
•
•
Set-point Difference is 14°F (8°C)
Tank Set-point Differential is 9°F (5°C)
The “Key Lock” icon will be displayed if the water heater
is either in the lock or unlock condition. The Icon is
composed of 3 components, the base, a locked and an
unlocked arc.
Switching between operating modes is done by pressing
the “Mode” Button when the Key Lock is “Off”. When
a mode is active, the corresponding LED is turned on.
Pressing the “Mode” button will cycle between the three
possible modes of operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Numeric Display
Burner in Operation
Numeric information such as temperature set-point,
maintenance codes and error codes are displayed using
a large yellow LED display.
When the burners are in operation and flame is detected
by the flame sensor, the flame symbol is illuminated.
Switching Between Units of Measure
Up and Down Buttons
Switching between temperature units of measure (°F/°C).
Two yellow LEDs will be used to light up the current unit
mode, °F or°C. To switch units of measure, simultaneously
press the “Mode” button and the “Up” button.
Two buttons (with “Up” and “Down” arrows) are used
for adjusting the data on the display. Other secondary
functions such as turning the Key Lock “Off”, are described
in other sections.
Fault Indication
Temperature Set-point change
Two buttons (with “Up” and “Down” arrows) are used to
adjust the desired temperature set-point.
A red fault LED (lighting a large red exclamation point)
should be present on the display panel.
Maintenance mode
When the Temperature Set-point is displayed and the
Key Lock Is “Off”, pressing the Up Button will increase
the set-point and pressing the Down button will decrease
the set-point.
By simultaneously pressing the “Mode” and “down arrow”
buttons for 3 seconds the unit will allow access to the
maintenance mode.
NOTE: The Temperature Set-point cannot be adjusted
beyond the limits of the current Mode selected.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING DIAGRAM
N
B R O W
O L W L Y E
Y E L L O W
Y E L L O W
B L U E
R E D
R E G E N
O R A N G E
O R A N G E
W H I T E
W H I T E
B L A C K
B L U E
B R O W N
B L U E
G R E Y
Y E L L O W
B L A C K
G R E Y
G R E Y
B L U E
B L U E
B L U E
B L U E
B L U E
B L A C K
B L A C K
FIGURE 34
Download from Www.Somanuals.com. All Manuals Search And Download.
35
LIGHTING INSTRUCTIONS
FOR YOUR SAFETY READ BEFORE LIGHTING
FLAMMABLE
BEFORE LIGHTING: ENTIRE SYSTEM MUST BE FILLED WITH WATER AND AIR PURGED FROM ALL LINES
A. This appliance does not have a pilot. It is equipped with
an ignition device which automatically lights the burner.
Do NOT try to light the burner by hand.
• If you cannot reach your gas supplier, call the fire
department.
C. Do not use this appliance if any part has been under
water. Immediately contact a qualified installer or
service agency to replace a flooded water heater. Do
not attempt to repair the unit! It must be replaced!
B. BEFORE OPERATING smell all around the appliance
area for gas. Be sure to smell next to the floor because
some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone
in your building.
• Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
OPERATING INSTRUCTIONS
1.
STOP! Read the safety information above on
this label.
6. If the green light above the stand-by button is flashing,
press the stand-by button. If the green light is turned off
then the water heater will automatically light the burners.
7. Set the display to the desired setting. CAUTION: Hotter
water increases the risk of scald injury. Consult the
instruction manual before changing temperature.
8. If the appliance will not operate, follow the instructions
“TO TURN OFF GAS TO APPLIANCE” and call your
technician or gas supplier.
2. Ensure tank is filled with water and the gas line is
connected.
3. This appliance is equipped with a device which
automatically lights the burner. DO NOT TRY TO LIGHT
THE BURNER BY HAND.
4. Wait five (5) minutes to clear out any gas. If you smell
gas, STOP!
information
smell gas:
Follow “B” in the safety
above on this label. If you don’t
D
D
A
A
N
N
G
G
E
ER
R
:
:
Hotter water increases the
risk of scald injury. Consult the instruction
manual before changing temperature.
5. Turn on all electrical power to the appliance.
TO TURN OFF GAS TO APPLIANCE
1. Set the thermostat to the lowest setting.
2. Set the ON/OFF switch on the control panel to the “OFF”
position.
3. Turn off all electrical power to the appliance if service is
to be performed.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
HEAT CYCLE DEFINITIONS
STATE
DESCRIPTION
Pre-purge
Inter-Purge
Post-Purge
If the heat engine initial call-for-heat is successful (all checks are passed), the combustion fan
is energized. The fan is started at a high speed for several seconds and the system verifies the
fan speed. Input signals (from other parts of the water heater) are verified before completion of
pre-purge including fan current verification. If one of the checks fails then the unit moves into
the post-purge mode followed by the hard lockout mode and the appropriate error is displayed
(see Error Code List and Clear-out Procedure).
If the flame presence is detected the control delays a pre-determined amount of time keeping
the spark igniter energized. If flame presence is not detected within 5 seconds from the
moment the gas was allowed in the combustion chamber (three ignition trials) then the control
will initiate an ignition re-try for two more times. If flame presence cannot be verified within
the given timing and after the ignitions’ re-try (if applicable), the system enters the post-purge
mode and the gas flow is turned off.
The heat engine gas valve is now turned off and the fan speed is changed to high speed for
a predetermined time followed by a change of fan speed to a low value for the remaining
duration of the post purge mode. The control will also verify that the proper conditions are
maintained and there is no flame current sensed from the flame rod. If during the first stage
of the post-purge mode (high speed fan operation) conditions for a new call for heat are met
then the system will allow the state change to “Initial call for heat” only after the first stage of
the post-purge mode is complete.
Standby Mode
After successful completion of post-purge, the fan is turned off and the control will wait until
the determined conditions for a call for heat are met. In standby mode the unit continually
monitors the input and output conditions and if abnormal conditions are detected the unit will
enter in a lockout mode. If a call for heat is required and all checks are passed, the control
will return to the initial call for heat state.
Lockout mode
Proven Ignition
This is a non-operational mode following the detection of an error in the system. In this stage
the system displays an error message and continuously monitors input and output parameters.
The system can move from this state into the stand-by mode only if the error is cleared (typical
values for input and output parameters are recorded).
Once the power is turned on, the self-inspection is getting a normal status, water is turned
on and fan’s current is normal then the ignition process will start for 5 seconds. If ignition is
successful, the heater will go to normal combustion state and the ignition sparking will stop
after 3 seconds. If ignition fails, the control will attempt to cycle through the heating stage
three times and then attempt to re-ignite the gas. If ignition cannot be achieved, the control
will end ignition attempts and prevent any more heating cycles, close the gas valve, turn the
blower on, and display the E28 error message to the user.
TABLE 2
Download from Www.Somanuals.com. All Manuals Search And Download.
37
TEMPERATURE REGULATION
THIS WATER HEATER IS EQUIPPED WITH AN
ADJUSTABLE THERMOSTAT TO CONTROL WATER
TEMPERATURE. HOT WATER TEMPERATURES
REQUIRED FOR AUTOMATIC DISHWASHER AND
LAUNDRYUSECANCAUSESCALDBURNSRESULTING
IN SERIOUS PERSONAL INJURY AND/OR DEATH.
THE TEMPERATURE AT WHICH INJURY OCCURS
VARIES WITH THE PERSON’S AGE AND THE TIME
OF THE EXPOSURE. THE SLOWER RESPONSE
TIME OF CHILDREN, AGED OR DISABLED PERSONS
INCREASES THE HAZARDS TO THEM. NEVERALLOW
SMALL CHILDREN TO USE A HOT WATER TAP, OR
TO DRAW THEIR OWN BATH WATER. NEVER LEAVE
A CHILD OR DISABLED PERSON UNATTENDED IN A
BATHTUB OR SHOWER.
FIGURE 35
It is recommended that lower water temperatures be used
to avoid the risk of scalding. It is further recommended,
in all cases, that the water temperatures be set for the
lowest temperature which satisfies your hot water needs.
This will also provide the most energy efficient operation
of the water heater.
THE WATER HEATER SHOULD BE LOCATED IN AN
AREA WHERE THE GENERAL PUBLIC DOES NOT
HAVE ACCESS TO SET TEMPERATURES.
SETTING THE WATER HEATER TEMPERATURE
AT 120°F (49°C) WILL REDUCE THE RISK OF
SCALDS. Some states require settings at specific lower
temperatures.
The water temperature is controlled using the Temperature
Control on the Display at the front of the unit (see Figure
3). This control utilizes a temperature probe to determine
the tank temperature. The primary temperature probe is
located at the top of the tank.
The temperature may be adjusted from 90°F (32°C) to
158°F (70°C). The thermostat was adjusted to 105°F
(43°C) before the heater was shipped from the factory. It
is recommended that lower water temperature be used
to avoid the risk of scalding. It is further recommended, in
all cases, that the water temperature be set for the lowest
temperature which satisfies your hot water needs. This
will also provide the most energy efficient operation of the
water heater and minimize scale formation.
HOT WATER CAN SCALD: Water heaters are intended to
produce hot water. Water heated to a temperature which
will satisfy space heating, clothes washing, dish washing,
and other sanitizing needs can scald and permanently
injure you upon contact. Some people are more likely to
be permanently injured by hot water than others. These
include the elderly, children, the infirm, or physically/
mentally handicapped. If anyone using hot water from this
heater fits into one of these groups or if there is a local code
or state law requiring a certain temperature water at the
hot water tap, then you must take special precautions. In
addition to using the lowest possible temperature setting
that satisfies your hot water needs, a means such as a
mixing valve, should be used at the hot water taps used
by these people or at the water heater. Mixing valves are
available at plumbing supply or hardware stores (see
Figure 3). Follow manufacturer’s instructions for installation
of the valves. Before changing the factory setting on the
thermostat, read the “Temperature Regulation” section in
this manual.
Valves for reducing the point-of-use temperature by mixing
cold and hot water are available (see Figure 2). Also
available are inexpensive devices that attach to faucets to
limit hot water temperatures. Contact a licensed plumber
or the local plumbing authority.
The table below shows the approximate time-to-burn
relationship for normal adult skin. Short repeated heating
cycles caused by small hot water uses can cause
temperatures at the point of use to exceed the thermostat
setting by up to 20°F (11°C). If you experience this type of
use, you should consider using lower temperature settings
to reduce scald hazards.
Never allow small children to use a hot water tap, or to draw
their own bath water. Never leave a child or handicapped
person unattended in a bathtub or shower.
The water heater should be located in an area where
the general public does not have access. If a suitable
area is not available, a cover should be installed over the
thermostat to prevent tampering. The water temperature
setting was factory set at the lowest temperature;
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Three LED’s are used to indicate the Operating Mode
Selection
Time for
Permanent Burns
2nd & 3rd Degree
(Most Severe
Burns)
Time for 1st
Degree Burn
(Less Severe
Burns)
Water
Temperature
Vacation Mode:
Energy Saver Mode: Green LED
Boost Mode: Orange LED
Yellow LED
110°F (44°C) (normal shower
temp.)
The Operating Modes have the following characteristics:
Vacation mode:
116°F (47°C) (pain threshold)
•
Fixed temperature setting of 90°F (32°C)
116°F (47°C)
122°F (50°C)
131°F (55°C)
140°F (60°C)
149°F (65°C)
154°F (68°C)
35 minutes
1 minute
45 minutes
5 minutes
25 seconds
5 seconds
2 seconds
1 second
Energy Saver mode:
•
Temperature range from 100°F to 135°F (38°C to 57°C)
in increments of 1°F or 1°C
5 seconds
2 seconds
1 second
Boost mode:
•
Temperature range from 140°F to 158°F (60°C to 70°C)
in increments of 1°F or 1°C
instantaneous
(U.S. Government Memorandum, C.P.S.C., Peter L.
Armstrong, Sept. 15,1978)
Switching between operation modes is done by pressing
the “Mode” Button when the Key Lock is “Off”. When
a mode is active, the corresponding LED is turned on.
Pressing the “Mode” button will cycle between the three
possible modes of operation.
TABLE 3
Setting Desired Temperatures
1. Set the key lock to the “Off” position
2. Select the desired mode button (vacation, energy saver
or boost)
3. Using the arrow buttons select the desired
temperature
Each time the “Mode” Button is changed by the user,
the controller display is to respond with the following
actions:
1. The Temperature Set-point changes to the lowest
temperature for the respective mode (e.g. 100°F (38°C)
for “Energy Saver” and 140°F (60°C) for “Boost” mode)
and is communicated to the master device.
2. The LED corresponding to the new mode is turned
on.
Key Lock
NOTE: This is a tamper resistant feature.
The Key Lock is considered “On” or “Off”:
•
Key Lock is turned “On” one minute after the unit has
been plugged in.
•
Key Lock can then be turned “Off” for one minute
by simultaneously pressing the “Up” Button and the
“Down” Button for three seconds.
UNIQUE HYBRID FEATURES
Temperature Measurement
Temperature Probes
The water heater has support for three independent
temperature probes:
1. Water Inlet Temperature Probe
When the keys are locked, the Temperature Set-point
cannot be increased or decreased, and the Operating
Mode cannot be changed.
The water inlet temperature probe contains a
thermistor and measures the temperature of the
water entering the heat engine enclosure.
2. Water Outlet Temperature Probe
The water outlet temperature probe contains a
thermistor and measures the temperature of the
water leaving the heat engine enclosure. This supply
of (hot) water is delivered to the top of the storage
tank in close proximity to the outlet fitting.
3. Tank Temperature Probe
The On/Off Button is not affected by the Key Lock feature.
All other buttons are “locked” when the Key Lock is
“On”.
A lock or unlock LED icon will display the condition. The
Icon will be composed of 3 components, the base, a locked
and an unlocked arc.
Operating Mode Selection
Operation modes are: Boost (peak demand), Energy Saver
and Vacation.
The tank probe contains a thermistor and measures
the temperature of the water in the storage tank at
a specific location between the top and the bottom
of the tank.
Initial conditions after starting-up the control is determined
by evaluation of the stored set-point.
Vacation Mode is selected if the Temperature Set-point
value is less than 100°F (38°C). Boost Mode is selected if
the Temperature Set-point value is greater than or equal to
140°F (60°C). Energy Saver Mode is selected for all other
Temperature set-point values.
Download from Www.Somanuals.com. All Manuals Search And Download.
39
Water Circulation Pump
The power for the main gas valve is to be routed through
the Exhaust Vent High Temperature Switch causing the
main gas valve to be de-energized immediately when the
switch opens.
The status of the Exhaust Vent High Temperature switch
should be continually monitored by the controller. If an
open switch is detected, the control should declare a
fault and respond according to the fault. The fault is a
continuous lockout.
A circulation pump is integrated into the heat engine for
the Hybrid application. The pump serves to push water
through the heat engine at a rate that supports optimum
recovery time and maximum heat output.
The control provides 120Vac, 60Hz line power to the pump
to enable operation.
Water Flow Measurement
1. Water Flow Sensor
The Water Flow Sensor uses a sensor for the
detection of the water flow. When water flows, the
sensor rotates and a transistor is switched on and
off, producing a pulsing signal with a frequency
related to flow rate.
Energy Cut Out (ECO) Temperature Switch
The heat exchanger of the heat engine is equipped with a
surface-mounted bimetallic switch which opens when the
water temperature exceeds the safe operating temperature
for the water heater.
2. Water Flow Detection
•
•
Opening Temperature is 185°F +/-9°F (85°C +/-5°C)
Closing Temperature is 149°F +/-6°F (65°C +/-3°C)
Flow detection is an on/off indication of whether
there is sufficient flow through the heat exchanger
for normal heating.
The power from the main gas valve is to be routed
through the ECO switch causing the main gas valve to be
immediately de-energized when the switch opens.
The status of the ECO switch should be continually
monitored by the controller. If an open switch is detected,
the control should declare a fault and respond according
to the fault. This will be a continuous lockout.
3.
If the water is less than 0.58 gal/min (2.2 l/min) the
unit stops and will start again when the flow is above
0.78 gal/min (2.7 l/min).
Water Flow Restriction Valve
A motorized valve is placed in series with the circulation
pump and the heat exchanger of the heat engine. This
valve serves to limit the amount of flow through the heat
engine such that a variable rate of flow can be achieved
from the fixed-speed pump.
Blocked (Exhaust Gas) Outlet Detection
If the exhaust air passage is obstructed, the control is to
enter a fault state and initiate a controlled shut down. This
is an overall safety feature of the control system.
Gas Delivery Safety String
The release of gas into the combustion chamber is of
critical importance to the safe operation of the heater.
The control is a combination of hardware and software
that measure and ensure the gas is released only when
appropriate for combustion. The term “safety string” applies
to those devices or components that directly control the
power applied to the gas valves as well as the gas valves
themselves. The components are:
Igniter
The control has an integrated direct spark ignition, which
can turn on, by means of a relay. This feature is integrated
onto the controller board.
By default, the control will allow for three ignition retries
after a failed ignition.
Flame Sensor
•
•
•
•
main gas valve solenoid,
An active flame is sensed through a flame rod located in
the burner assembly in the region of the burners flame.
The flame sense input will be monitored by the control and
respond to the presence of the flame.
stage 1 and 2 gas valve solenoids,
exhaust vent high temperature switch,
energy cut out (ECO) temperature switch.
Exhaust Vent High Temperature Switch
Combustion Chamber Temperature Protection
(Thermal Fuse)
If in any conditions when the temperature increases over
287.6°F (142°C) the High Limit Temperature Fuse melts.
This function disconnects the power supply controller, and
must be replaced.
The water heater is designed for plastic vent piping typically
used in high efficiency appliances. To ensure the water
heater will not release exhaust gasses at temperatures that
would cause the vent piping to melt, a bimetallic switch is
mounted on the assembly. The switch used is a normally-
closed switch which will open when the temperature
reaches the maximum design temperature for the venting
used. This switch should reset to the closed position when
the vent pipe temperature cools sufficiently.
•
Opening Temperature is approximately 165°F (74°C)
+/- 5°F (2.8°C).
•
Closing Temperature is approximately 135°F (57°C)
+/- 5°F (2.8°C).
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Line Voltage Monitor
Storage Tank Call For Heat
The control monitors the line voltage provided to
the system. If the line voltage is too low, the system
components may not operate properly. For diagnostic
purposes, the display panel should indicate that the cause
was power-related.
The storage tank call for heat is generated when the tank
thermistor temperature drops below the storage tank set-
point minus the fixed storage tank differential.
At the end of a call for heat the tank thermistor’s
temperature is equal to or greater than the storage tank
set-point.
•
If line power is below 102Vac, the water heater will enter
the fault state and initiate a controlled shut-down. The
fault will automatically clear if the voltage is restored
to 102Vac or above.
Temperature Control Modes
The temperature control functions can operate under
one of the pre-defined user-selected control modes. The
temperature control mode serves to limit the range of the
(heat engine) temperature set-point and the storage tank
differential.
•
If line power is above 132Vac, the water heater will enter
the fault state and initiate a controlled shut-down. The
fault will automatically clear if the voltage is restored
to 132Vac or below.
Please reference the Operating Mode Selection for details
of how the set-point and differentials are adjusted for
the different modes. In brief, three modes are provided:
Vacation Mode, Energy Saver Mode, and Boost Mode.
The temperature control mode will be maintained after a
power loss. Upon restoring power, the temperature set-
point is set to the last temperature.
TEMPERATURE REGULATION
Temperature regulation is the process by which the
controller determines when the water heater is to heat
water as well as when to stop the heating process. This
section defines how the water heater is to regulate the
temperature.
The default setting is 105°F (41°C) in the Energy Saver
Mode.
Temperature Units of Measure
The water heater control will display the temperatures in
either °C or °F (as per selected unit of measure). The main
temperature unit is °C and all the calculations, within the
control system, are done using temperature values in °C.
The display has the capability to perform a conversion from
°C to °F. The resulting temperatures in °F will be rounded
off to the nearest degree.
Outlet Temperature Limit Control
Your water heater is designed to provide a constant outlet
water temperature. The water heater takes into account
dynamic conditions of the heat engine such as the inlet
water temperature, flow rate, gas flow adjustment, etc and
establishes the optimum performance.
The control will end the call for heat if the outlet thermistor
temperature exceeds the set-point by a fixed amount.
The call for heat may be restored if the outlet thermistor
temperature drops below the set-point by 5.4°F (3°C) or
more.
Temperature Set-point
The adjustable temperature set-point is used to determine
the desired outlet temperature of the water heater.
The water outlet of the heat engine feeds the outlet of the
storage tank although some mixing does occur with the
water at the top of the storage tank. For this reason, the
temperature of water delivered is considered equivalent
to the heat engine output temperature.
This value is to be set within the acceptable range of 90°F
(32°C) and 158°F (70°C) when selecting the operating
modes.
As a safety measure, the control is to ensure that the set-
point cannot be adjusted outside of this range.
If the water flow is turned off and then is turned on, the
controller remembers and automatically resets to the last
temperature.
Inlet Temperature Limit Control
To add protection to the system, an over-temperature
comparison is made on the inlet water temperature.
The water heater will end the call for heat if the inlet
thermistor temperature is above the set-point.
The call for heat may be restored if the inlet thermistor
temperature drops below the set-point.
If a power outage occurs or the unit is energized/de-
energized by the STANDBY symbol for re-booting, the
controller resets to the last temperature setting.
After clearing a continuous lockout error code the unit
will always go back to the factory default temp setting
and mode.
Storage Tank Set-point
The control is required to maintain a storage tank set-point
differential temperature.
Download from Www.Somanuals.com. All Manuals Search And Download.
41
CONSTANT OUTPUT TEMPERATURE CONTROL
While the temperature regulation in the previous section
describes the features of temperature monitoring and
regulation, your water heater goes beyond the on/off
control implied there and implements a gas, air and water
flow modulation scheme to provide a constant water
delivery temperature from the heat engine for the duration
of the call for heat.
OPERATIONAL CONDITIONS
Smelly Water
In each water heater there is installed at least one anode
rod (see parts section) for corrosion protection of the tank.
Certain water conditions will cause a reaction between this
rod and the water. The most common complaint associated
with the anode rod is one of a “rotten egg smell” in the hot
water. The smell is a result of four factors which must all
be present for the odor to develop:
Heat Needed during Normal Operation
a. A concentration of sulfate in the supply water.
b. Little or no dissolved oxygen in the water.
c. A sulfate reducing bacteria which has accumulated
within the water heater (this harmless bacteria is
nontoxic to humans).
The amount of heat needed is based on the amount
of water flowing through the heater and the amount of
temperature rise that needs to be generated to meet your
demands. The system will calculate the amount of heat
needed.
d. An excess of active hydrogen in the tank. This is caused
by the corrosion protective action of the anode.
The temperature regulation will prevent the inlet
temperature from reaching the temperature set-point.
Smelly water may be eliminated or reduced in some
water heater models by replacing the anode(s) with one
of less active material, and then chlorinating the water
heater tank and all water lines. Contact the local water
heater supplier or a qualified service agency for further
information concerning an Anode Replacement Kit and
this chlorination treatment.
Detection of Failure to Maintain Desired Constant
Temperature
This check can be used to detect a failure of the stage
2 gas valve. In this case, an insufficient amount of heat
would be applied. This check can also serve to diagnose
failures or mis-wiring of the water flow restriction valve. If
the valve fails to restrict the flow of water, the system may
not be able to sufficiently heat the water passing through
the heat engine.
If the smelly water persists after the anode replacement
and chlorination treatment, we can only suggest that
chlorination or aeration of the water supply be considered
to eliminate the water problem.
A failure to maintain the desired constant temperature is
determined by the outlet water temperature remaining 15
degrees lower than the set-point for one minute while the
flame is established. If this condition is detected while in
the heating state for normal modes, an Alert message is
provided to the display panel.
Do not remove the anode leaving the tank unprotected.
By doing so, all warranty on the water heater tank is
voided.
“Air” In Hot Water Faucets
START UP CONDITIONS
Smoke/Odor
It is not uncommon to experience a small amount of
smoke and odor during the initial start-up. This is due to
burning off of oil from metal parts, and will disappear in
a short while.
NOTE: If there is a discharge from the temperature-
pressure relief valve, refer to the “THERMALEXPANSION”
section of this manual.
HYDROGEN GAS: Hydrogen gas can be produced in a
hot water system that has not been used for a long period
of time (generally two weeks or more). Hydrogen gas is
extremely flammable and explosive. To prevent the
possibility of injury under these conditions, we recommend
the hot water faucet, located farthest away, be opened for
several minutes before any electrical appliances which
are connected to the hot water system are used (such as
a dishwasher or washing machine). If hydrogen gas is
present, there will probably be an unusual sound similar
to air escaping through the pipe as the hot water faucet is
opened. There must be no smoking or open flame near
the faucet at the time it is open.
NOTE: Do not plug the temperature-pressure relief
valve.
Strange Sounds
Possible noises due to expansion and contraction of some
metal parts during periods of heat-up and cool-down do not
necessarily represent harmful or dangerous conditions.
Condensation causes sizzling and popping within the
burner area during heating and cooling periods and should
be considered normal. See “CONDENSATE” section.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
HOUSEKEEPING
Vacuum around base of water heater for dust, dirt, and
lint on a regular basis.
VENTING SYSTEM INSPECTION
At least once a year a visual inspection should be made
of the venting system. You should look for:
1. Obstructions which could cause improper venting.
The combustion and ventilation air flow must not be
obstructed.
2. Damage or deterioration which could cause improper
venting or leakage of combustion products.
Be sure the vent piping is properly connected to prevent
escape of dangerous flue gasses which could cause
deadly asphyxiation.
Obstructions and deteriorated vent systems may present
serious health risk or asphyxiation.
INSTALLED IN SUITABLE AREA: To insure sufficient
ventilation and combustion air supply, proper clearances
from the water heater must be maintained. See “Facts to
Consider About Location” section. Combustible materials
such as clothing, cleaning materials, or flammable liquids,
etc. must not be placed against or adjacent to the water
heater which can cause a fire.
Chemical vapor corrosion of the flue and vent system
may occur if air for combustion contains certain chemical
vapors. Spray can propellants, cleaning solvents,
refrigerator and air conditioner refrigerants, swimming pool
chemicals, calcium and sodium chloride, waxes, bleach
and process chemicals are typical compounds which are
potentially corrosive.
If after inspection of the vent system you found sooting or
deterioration, something is wrong. Call the local gas utility
to correct the problem and clean or replace the flue and
venting before resuming operation of the water heater.
ANODE ROD INSPECTION
BURNER OPERATION AND INSPECTION
Flood damage to a water heater may not be readily visible
or immediately detectable. However, over a period of time
a flooded water heater will create dangerous conditions
which can cause DEATH, SERIOUS BODILY INJURY,
OR PROPERTY DAMAGE. Contact a qualified installer or
service agency to replace a flooded water heater. Do not
attempt to repair the unit! It must be replaced!
At least once a year a visual inspection should be made of
the main burner and spark generator assembly for proper
flame characteristics and ignition sequences. You should
also check for sooting. Soot is not normal and will impair
proper combustion. Soot build-up indicates a problem that
requires correction before further use. Turn “OFF” gas to
water heater and leave off until repairs are made, because
failure to correct the cause of the sooting can result in a
fire causing death, serious injury, or property damage.
The anode rod is used to protect the tank from corrosion.
Most hot water tanks are equipped with an anode rod. The
submerged rod sacrifices itself to protect the tank. Instead
of corroding the tank, water ions attack and eat away the
anode rod. This does not affect the water’s taste or color.
The rod must be maintained to keep the tank in operating
condition.
Anode deterioration depends on water conductivity, not
necessarily water condition.Awater softener can affect the
life of the anode installed in this water heater. A corroded
or pitted anode rod indicates high water conductivity and
should be checked and/or replaced more often than an
anode rod that appears to be intact. Replacement of a
depleted anode rod can extend the life of your water
heater. Inspection should be conducted by a qualified
technician, and at a minimum should be checked annually
after the warranty period.
Download from Www.Somanuals.com. All Manuals Search And Download.
43
ANODE ROD REPLACEMENT
To replace the anode:
If the temperature-pressure relief valve on the appliance
weeps or discharges periodically, this may be due to
thermal expansion. You may have a check valve installed in
the water line or a water meter with a check valve. Consult
your local water supplier or a qualified service agency for
further information. Do not plug the temperature-pressure
relief valve.
1. Turn off gas supply to the water heater.
2. Shut off the water supply and open a nearby hot-water
faucet to depressurize the water tank.
3. Drain approximately 5 gallons (20 litres) of water from
tank (Refer to “DRAINING THE TANK” for proper
procedures.) Close drain valve.
4. Remove old anode rod.
MOTORS
5. Use Teflon® tape or approved pipe sealant on threads
and install new anode rod.
6. Turn on water supply and open nearby hot-water
faucet to purge air from water system.
Motors are permanently lubricated and do not need
periodic lubrication. Keep fan and motor free of dust and
dirt by cleaning annually.
7. Restart the water heater as directed under “Operating
Your Water Heater”. See the “Parts Reference
Illustration” for anode rod location.
SNOW ACCUMULATION
Keep the area around flue terminal free of snow and ice.
The appliance will not function properly if the intake air
or exhaust is impeded (blocked or partially blocked) by
obstructions.
TEMPERATURE-PRESSURE RELIEF VALVE
OPERATION
CLEANING THE INLET WATER FILTER
The cold water inlet filter must be cleaned on a regular
basis. The frequency of this cleaning is dependent on the
quality of your local water supply. You will need to prepare
a bucket to collect some of the draining water. The cold
water inlet filter is located inside the door on the left-hand
side of the heat engine. To access the inlet filter:
Access To
Door Pins
Door
Lock
FIGURE 36
The temperature-pressure relief valve lever must be
operated at least once a year to ensure that the water
ways are clear. When checking the temperature-pressure
relief valve operation, make sure that:
1. No one is in front of or around the outlet of the
temperature-pressure relief valve discharge line.
2. The water discharge will not cause any property
damage, as the water may be extremely hot.
3. A discharge line is connected to this valve, directing
the flow of hot water from the valve to a proper
placement for disposal.
If water does not flow freely when the lever is in the open
position, replacement of the valve is required. Turn off the
cold water inlet heater and call a qualified service man.
If after manually operating the valve (see Figure 36), it
fails to completely reset and continues to release water,
immediately close the cold water inlet to the water
heater, follow the draining instructions, and replace the
temperature-pressure relief valve with a new one.
FIGURE 37
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove the filter:
FLUSHING THE HEAT EXCHANGER (LIME BUILD-
UP)
•
•
Disconnect the electrical power to the water heater.
Close the shutoff valves on both the hot-water and
cold-water lines.
The heat exchanger must be cleaned on a regular basis
to reduce lime build-up. The frequency of this cleaning
is dependent on the quality of your local water supply.
Failure to flush the appliance will cause damage to the
heat exchanger. Damage caused by lime build-up is not
covered by the unit’s warranty.
•
•
•
•
•
Unlock the door by rotating the side lock counter-
clockwise with a wide, slot screwdriver.
Pop the top and bottom door pins by pushing the pins
out, using a small screwdriver. Open the door.
Open a nearby hot water faucet to depressurize the
water tank.
Drain the tank following the instructions in the “Draining
The Tank” section.
Unscrew the filter and clean by rinsing it under a faucet
and scrubbing with a brush if required.
•
•
Disconnect electrical power to the water heater.
Close the shutoff valves on both the hot water and cold
water lines.
•
•
Drain the tank using the instructions in the “Draining
The Tank” section.
Disconnect the hoses joining the tank and the heat
engine (upper hose is water outlet and lower hose is
water inlet).
Heat
Engine
Cabinet
•
Connect addition length of hose (not provided) to
existing hoses. (Note: The heat engine hose is a
3/4” NPT thread which is different for a garden hose
thread.)
Water
Inlet Filter
5 gallon pail of virgin,
food grade, white
vinegar (or virgin,
food grade,
citric acid).
Hot Water
Line
Water Inlet
Fitting
FIGURE 38
Install the filter:
•
•
•
Install the clean filter.
Close the drain valve.
Open the shutoff valves on both the hot-water and
cold-water lines.
Cold Wat
Line
•
Fill the tank following the instructions in the
“Filling The Water Heater” section in this Manual.
Close and lock the door.
Reconnect the electrical power to the water heater.
Restart the water heater following the Lighting
Instructions found in the Operating Manual.
•
•
•
FIGURE 39
•
Connect a pump to the hose running to the heat
engine water inlet (lower fitting). We recommend a
submersible utility pump for the circulating pump. (Note:
If a submersible pump is not used, connect a hose from
the circulating pump to the cleaning solution.)
Pour approximately 4 gallons (15 litres) of virgin, food
grade, white vinegar or citric acid into a 5 gallon or
greater pail.
Place the “intake” and “output” hoses into the pail of
cleaning solution. If a submersible utility pump is used,
place the pump into the pail of cleaning solution.
Plug in the circulating pump.
CLEANING THE HEAT ENGINE
It is imperative that the control compartment burner and
circulating air passageways of the appliance is kept
clean.
•
•
•
Turn off and disconnect the electrical power. Allow to
cool.
Remove and clean the water inlet filter. See “Cleaning
The Inlet Water Filter” section.
•
•
•
•
•
Remove the front panel.
Connect the electrical power to the water heater and
run the heat engine.
Use a low air pressure to remove dust from the main
burner, heat exchanger, and blower. Do not use a wet
cloth or spray cleaners on the burners.
•
Operate the heat engine to circulate the cleaning
solution through the system for at least 45 minutes.
(Note: Lower the temperature below 104°F (40°C) or to
vacation mode.) Warning: Water will become hot very
quickly.
NOTE: Do not use volatile substances such as benzene
and thinners. They may ignite or fade the paint.
Download from Www.Somanuals.com. All Manuals Search And Download.
45
•
•
Disconnect electrical power to the water heater.
Remove the pail of cleaning solution and replace it with
a pail of clean water.
Rinse the cleaning solution from the water heater as
follows:
Connect the electrical power to the water heater and
run the heat engine.
Allow the clean water to flow through the heat engine
for 5 minutes.
FAULT INDICATION AND ERROR CODES
A red fault LED (lighting a large red exclamation point)
should be present on the display panel if a fault condition
exists.
•
•
•
•
A history of the last 9 error codes along with the current
error code is stored in memory and can be accessed via
the maintenance mode. If the current error code is zero,
“E00” shall be displayed (see Table 4).
Disconnect electrical power to the water heater and
circulating pump.
•
•
Disconnect the hoses from the heat engine.
Disconnect hoses and circulating pump, draining the
cleaning solution into the pail.
•
•
Reconnect the original hoses to the tank.
Remove the in-line filter at the cold water inlet and
clean out any residue. Assemble the filter back into the
unit.
•
Open the shutoff valves on both the hot water and cold
water lines.
•
•
•
Fill the tank with water.
Connect the electrical power to the water heater.
Restart water heater following lighting instructions.
DRAINING THE TANK
The water heater should be drained if being shut down
during freezing temperatures. Also periodic draining and
cleaning of sediment from the tank may be necessary.
1. Set the power switch to the “OFF” position.
2. OPEN a nearby hot water faucet and let the water run
until it is no longer hot.
3. CLOSE the cold water inlet valve to the water
heater.
4. Connect a hose to the drain valve and terminate to
an adequate drain.
5. OPEN the water heater drain valve to allow for tank
draining. NOTE: If the water heater is going to be
shut down and drained for an extended period,
the drain valve should be left open with hose
connected allowing water to terminate to an
adequate drain.
6. CLOSE the drain valve.
7. Follow instructions in the “Filling The Water Heater”
section.
8. Follow the lighting instructions on the label or see
“Lighting Instructions” in this manual to restart the
water heater.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGNOSTIC DISPLAY
By simultaneously pressing the “Mode” and “down arrow” buttons for 3 seconds the unit will allow access to the diagnostic
mode.
In diagnostic mode, using the up/down arrow allows for cycling between diagnostic codes. The numeric display will
show the diagnostic code for 1 second, followed by the actual measurement displayed for 3 seconds. For example, H01
- 105 represents the diagnostic code of “H01” and the value of “105” is the inlet water temperature measurement. The
display will continue to show the diagnostic code and the measurement value unless the up or down arrows are pressed
to switch to the next item (see Table 4). If no buttons are pressed for 30 seconds the unit will revert back to operation
mode where the set-point temperature is displayed.
Code and
Displayed
Diagnostic
Code
Measurement
Display
Units
Description
characters
(Example of)
Meaning
Remarks
(Example of)
Format
H01
H02
H03
H04
Inlet Water
Temperature
H01 – xxx
H02 – xxx
H03 – xxx
H04 – xxx
ºC or ºF
ºC or ºF
041 or 105
041 or 105
041 or 105
056
41ºC or 105ºF
41ºC or 105ºF
41ºC or 105ºF
ºC LED or ºF
LED turned ON
Heat engine outlet
water temperature
ºC LED or ºF
LED turned ON
Storage tank
temperature
ºC or ºF
ºC LED or ºF
LED turned ON
Heat engine water
litres/minute
5.6 litres/minute
(1.48 Gallons/
minute)
1 litre =
0.264 Gallons
1 gallon =
flow rate
3.78 litres
H05
H06
H07
H08
H09
H10
H11
Fan Speed
Fan Current
H05 - __x – xxx
H06 - __x – xxx
H07 – xxx
rpm
mA
006_511
001_456
178
6511 rpm
rpm=rotations
per minute
1456 mA
(1.456A)
mA=milliampers
Proportional Valve
Current
mA
178 mA
mA=milliampers
Total Heating
Time
H08 – xxx – xxx
hours
001_234
000_459
100
1234 hours
(51.41 days)
Total Cycles
H09 – xxx – xxx heating cycles
459 heating
cycles
Heat Engine
Rated Output
H10 – xxx
H11 – xxx
KBtu/hour
N/A
100 KBtu/hour
Current Error
Code (See Fault
Code Table)
E00
Proper operation
- No error
H12 – H20
Error Code
History, From the
Most Recent to
the Least Recent
(See Fault Code
Table)
Hxx – xxx
N/A
E28
Ignition failure
The most
recent error
corresponds
to H12 and the
least recent to
H20
H21
Software
Release Number
(CWHCB)
H21 – xxx – xxx
N/A
002_025
Software release
number 2.25
For the main
controller board
H22
H23
Software Release H22 – xxx – xxx
Number (UIM)
N/A
N/A
002_009
000_006
Software release For the display
number 2.09
board
Configuration File H23 – xxx – xxx
Configuration file
Number
number 6
TABLE 4
Download from Www.Somanuals.com. All Manuals Search And Download.
47
If an error code is displayed, or odd behavior of the unit occurs, the first corrective action should be to “Cycle the Power”:
Unplug the 120Vac power cord and after 5 seconds plug it in again. If this doesn’t clear the fault, proceed with the
“Remedy” in the following table (Table 5).
If wire harness checking is required, examine the integrity of wires themselves, the connector housings, the integrity of
the terminals as well as condition of the crimps.
Fault
Code
Displayed
Lockout
type
Description
Cause
Remedy
Control detects that the
Invalid Rated
KBtu/Model Type. defined or the configuration
configuration selected is not
Change the main controller board
(board).
E01, E02
Continuous
has never been set.
Control detects that a relay
E03, E04, Main Valve Relay used to enable the Main
E05, E06 Out Of Sequence. Valve has failed in either the
open or closed position.
Soft
Soft
Change the board.
E07
Flame Detected.
Flame detected when no
1. Check the flame rod.
2. Check the flame wire harness.
3. Change the board.
flame was expected.
E08
ECO switch is
open.
Control detects that the
ECO switch is open,
preventing power to the
Main Valve.
1. Measure the water temperature.
ECO switch open temperature
is 85±5ºC (185±14ºF) and close
temperature is 65±5ºC (149±14ºF).
2. Check the ECO switch.
Continuous
Continuous
3. Check the ECO wire harness.
4. Change the board.
E09
High temperature Control detects that the High
Vent Switch Open. Temperature Vent Switch is
open, preventing power to
1. Measure the water temperature.
High Vent Switch open temperature
is 74±2.8ºC (165±5ºF) and close
temperature is 57±2.8ºC (135±5ºF).
2. Check the switch.
the Main Valve.
3. Check the High Vent Switch wire
harness.
4. Change the board.
E10
E11
120Vac too high.
120Vac too low.
120Vac > Overvoltage Limit.
Nominal voltage is 120Vac.
Overvoltage limit is 132Vac,
Undervoltage limit is 102Vac.
1. Check the power cord.
120Vac < Undervoltage
Limit.
Auto Reset 2. Check the wall outlet.
3. Measure the voltage at the board
connector J7 between pin1 and pin
3. If the voltage is between limits,
change the board.
E12
E13
E14
Blower Current meets
requirements for a
completely blocked flue.
1. Check the venting system. If the
venting system is clear, recalibrate
the unit.
2. Check the blower wire harness.
3. Change the blower.
Blower Current meets
requirements for a partially
blocked flue.
Blower Current
abnormal.
Soft
Blower Current meets
requirements for a non-
heating blocked flue
evaluation.
4. Change the board.
TABLE 5
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Fault
Code
Displayed
Lockout
type
Description
Cause
Remedy
E15
E16
E17
E18
Blower speed is 200RPM
below the target speed for
20 seconds.
Blower speed is 500RPM
above the target speed for 6
seconds.
Soft
1. Check the blower wire harness.
2. Change the blower.
3. Change the board.
Blower speed
abnormal.
Machine starts or normal
combustion, but Blower
speed = 0 for last 3sec.
Have Blower’s output signal
but the Blower speed = 0 for
last 400ms.
E19
E20
E21
E22
Blower speed stuck > 3000
rpm
Soft
Soft
Proportional valve Current <
Minimum.
1. Check the proportional gas valve
wire harness.
2. Change the board.
Proportional
valve (PV) current
unusual.
Proportional valve Current >
Maximum.
3. Change the gas valve assembly.
Outlet
Outlet Temperature
is < minimum defined
temperature.
Temperature
Probe is Open
circuit.
E23
Outlet
Outlet Temperature
is > maximum defined
temperature.
Temperature
Probe is Short
circuit.
E24
E25
E26
E27
E28
Inlet Temperature Inlet Temperature is
1. Check temperature probes wire
harness.
2. Replace themperature probe.
3. Change the board.
Probe is Open
circuit.
< minimum defined
temperature.
Soft
Inlet Temperature Inlet Temperature
Probe is Short
circuit.
is > maximum defined
temperature.
Tank Temperature Tank Temperature
Probe is Open
circuit.
is < minimum defined
temperature.
Tank Temperature Tank Temperature
Probe is Short
circuit.
is > maximum defined
temperature.
Ignition failure.
After a failure to detect
the flame during ignition,
the control will retry the
specified number of times.
After the maximum failed
attempts, this fault is
declared.
1. Check the igniter wire harness.
2. Check igniter 120Vac voltage
supply during the ignition time.
3. Check the ignition rod. If it looks
dirty clean it using isopropyl alcohol
and a clean cloth.
4. Check the high voltage wiring
connection between igniter and
igniter rod for proper contact.
Soft
E29
Outlet water
temperature too
low.
Outlet water temperature <=
(setting temperature – 15°C)
for 60 seconds after flame
detected.
1. Check the outlet temperature probe.
2. Change the board.
Alert
TABLE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
49
Fault
Code
Displayed
Lockout
type
Description
Cause
Locked Rotor.
Remedy
E30
E33
E34
Blower Error.
1. Check the blower wire harness.
2. Change the blower.
3. Change the board.
Soft
Soft
Water Flow Valve The water valve did not
Closed.
1. Check the water valve wire harness.
2. Change the board.
3. Change the water valve.
open when attempting to
establish flow.
Proportional Valve The closed loop control
(PV) Response
Too Slow.
Check the proportional gas valve wire
harness, change the board, change
the gas valve assembly
of the proportional valve
is not functioning properly
(control error) or the valve
is responding slowly (valve
failure).
Soft
Soft
E35
E36
Repeated Flame
Loss Fault.
Low Gas Inlet Pressure.
Check the flame rod wire harness,
check line gas pressure. If it is above
5” WC check the flame rod and if it
looks dirty, clean it up using isopropyl
alcohol and a clean cloth, change the
flame rod, change the board
Calibration error.
Calibration sequence
incomplete because end
of “call-for-heat” during
the calibration time, or
calibration sequence not
initiated because of lack of
“call-for-heat”, or the unit
has been never calibrated
or Calibration is successful
but DIP switch 4 not set to
“normal”.
1. Unplug the power cord, check the
DIP switch 4 position and put it in
ON position.
2. Increase the set point so that a
“call-for-heat” occurs.
3. Drain the tank in order to lower the
water temperature so that a “call-
for-heat” is generated.
4. Set DIP switch 4 to OFF position.
5. Recalibrate the unit.
Soft
6. Change the board.
E37
No Water Flow.
The heater could not start
because the water flow was
not established. This can be
caused by an air bubble or a
blockage in the heat engine
water passage, a failed flow
sensor or a failed circulation
pump.
1. Check the water inlet on the heat
engine.
2. Make a water draw during first 60
seconds after putting the unit in ON
mode (to evacuate possible air from
the heat engine water passage).
3. Check wire harness for pump, water
valve and water flow sensor.
4. Check the pump 120Vac voltage
supply (the pump shall be energized
during the heating mode).
Soft
5. Clean or change the water filter.
6. Change board.
7. Change pump.
8. Change water valve.
E99
Board Failure.
An internal diagnostic check
on the board has failed.
Soft
Change the board.
TABLE 5
Lockout types:
Continuous. Needs “Cycle the Power” or service to restart.
Soft. Will try to automatically recover and restart after 20 minutes.
Auto. Will automatically restart when voltage returns to acceptable parameters.
Alert. Will only display an error code in diagnostic mode.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
These guidelines should be utilized by a qualified service agent.
Problem
Possible Cause(s)
What to do
NOT ENOUGH HOT WATER
STANDBY button turned off.
No power at outlet.
Press switch to turn heater on.
Repair service to outlet.
Error Code being displayed
Refer to “FAULT INDICATION AND
ERROR CODES” section and Table
5 or call service agency or dealer.
Set point set too low.
Adjust Set point higher.
Reduce hot water use.
Contact dealer.
Heater undersized.
Low gas pressure
Incoming water is usually cold.
Leaking hot water pipes of fixtures.
Allow more time for heater to reheat.
Have plumber check and repair
leaks.
CONDENSATION
WATER LEAKS
Water on the floor under heater.
See CONDENSATE section.
Improperly sealed, hot or cold supply Check for leaks. See Figure 40.
connections, relief valve, drain valve
or thermostat threads.
Leakage from other appliances or
water lines.
Inspect other appliances near water
heater.
Condensation of flue products.
Refer to CONDENSATE section.
LEAKING T&P
Thermal expansion in closed water
system.
Install thermal expansion tank (Do
not plug T&P valve).
Improperly sealed valve.
Check relief valve for proper
operation (Do not plug T&P valve).
HOT WATER ODORS (refer to
cathodic protection)
High sulfate or mineral content in
water supply.
Drain and flush heater thoroughly
then refill.
Bacteria in water supply.
Thermostat set too high.
Chlorinate water supply.
HOT WATER TOO HOT
Refer to TEMPERATURE
REGULATION section.
WATER HEATER SOUNDS
Condensation dripping on burner.
Sediment at bottom of heater tank.
Refer to CONDENSATE above.
SIZZLING - RUMBLING NOISE
Clean sediment from tank. Refer to
DRAINING.
SOOTING
Improper combustion.
Refer to Air Requirements.
BURNER WILL NOT STAY LIT-
GOES OUT 4-5 SECONDS
High ambient room temperature.
Contact a qualified service agency to
determine cause.
Defective Control board.
Replace Control board.
Replace Flame Sensor
Damaged Flame Sensor
(Error code E35)
VENT GAS ODORS
Lack of air supply.
Improperly installed vent piping.
Downdraft
Shut off water heater immediately
and contact a qualified service
agency to determine cause.
Poor Combustion
THERE IS NO WATER AT ALL
WHEN THE HOT WATER TAP IS
OPENED.
The unit display is flashing an error
code.
Check if there is any error code
flashing on the remote controller.
TABLE 6
Download from Www.Somanuals.com. All Manuals Search And Download.
51
Problem
Possible Cause(s)
What to do
WHEN THE TAP IS OPENED,
THERE IS NO HOT WATER OR THE
HOT WATER TURNS COLD AND
STAYS COLD.
a.The hot water fixture is not
sufficiently open to draw the water the display.
through the heater.
b.The unit display is an error code.
c.There is an external recirculation
system installed, or there is a
check valve on the recirculation
return line.
Check if there is any error code on
d.Improper sized dip tube.
e.Water heater disconnected from
electrical power.
THE WATER IS NOT HOT
ENOUGH.
The temperature is set too low.
a.Check unit’s temperature setting.
b.Check for cross plumbing between
cold and hot water lines.
THE WATER IS TOO HOT.
CANNOT OPEN DOOR.
The temperature set too high.
Door pins locked in place.
Check unit’s temperature setting.
a.Ensure the door lock is unlocked
b.Ensure the top and bottom door
pins are released by using a small
screwdriver to pry the pins in the
direction of the door opening.
TABLE 6
52
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE
If a condition persists or you are uncertain about the
operation of the water heater contact a qualified service
agency.
LEAKAGE CHECKPOINTS
Use this guide to check a “Leaking” water heater. Many
suspected “Leakers” are not leaking tanks. Often the
source of the water can be found and corrected.
If you are not thoroughly familiar with gas codes, your water
heater, and safety practices, contact your gas supplier or
qualified installer to check the water heater.
Read this manual first. Then before checking the water
heater make sure the gas supply has been turned “OFF”,
and never turn the gas “ON” before the tank is completely
full of water.
Never use this water heater unless it is completely filled
with water. To prevent damage to the tank, the tank must
be filled with water. Water must flow from the hot water
faucet before turning “ON” gas to the water heater.
A *Condensation may be seen on pipes in humid weather
or pipe connections may be leaking.
A
H
C
B. Small amounts of water from temperature-pressure
relief valve may be due to thermal expansion or high
water pressure in your area.
C. *The temperature-pressure relief valve may be leaking
at the tank fitting.
D. Water from a drain valve may be due to the valve being
slightly opened.
E. *The drain valve may be leaking at the tank fitting.
F. Water in the water heater bottom or on the floor may
be from condensation, loose connections, or the relief
valve. DO NOT replace the water heater until a full
inspection of all possible water sources is made and
necessary corrective steps taken.
A
G. *The hose from the tank to the heat engine may be
leaking at the tank fitting.
H. *The fittings at the circulation pump may be leaking.
G
Leakage from other appliances, water lines, or ground
seepage should also be checked.
* To check where threaded portions enter the tank, insert
cotton swab between jacket opening and fitting. If cotton
is wet, follow “Draining The Tank” section instructions in
the “Maintenance” section and then remove fitting. Put
pipe dope or teflon tape on the threads and replace.
Then follow the instructions in “Filling the Water Heater”
section.
B
F
E
D
G
FIGURE 40
Download from Www.Somanuals.com. All Manuals Search And Download.
53
PARTS IDENTIFICATION
ITEM #
DESCRIPTION
A
B
C
D
E
F
Baffle, Flue
Hot Water Outlet Nipple (w/ Anode, Heat Trap)
T&P Relief Valve
Cold Water Inlet Nipple (w/ Dip Tube, Heat Trap)
Cover, Back-Flue Gas Return
Top Insulation
G
H
I
Flue Gas Return Duct Assy
Shroud, Back-Tank Assembly
Shroud, Right Side-Tank Assembly
Temperature Switch
J
K
L
Condensate Trap
Baffle, Exhaust
M
N
O
P
Q
R
S
T
Hose, 12” Braided (Heat Engine Cold In)
Drain Valve
Tank Thermistor (Probe)
Front Door Lock (Hook Cam)
Shroud, Right Side-Tank Assembly & Door
Display Subassembly
Heat Engine
Cover, Front-Flue Gas Return
Hi-Limit Temperature Switch
Air Inlet Cover (Direct Vent)
Air Inlet Cover Gasket (Direct Vent)
ECO Switch
U
V
W
X
Y
Z
Transformer
(PCB) Circuit Board Assembly (w/ Base)
Power Cord Assembly
Flame Sensor
1
2
3
Spark Generator
4
Gas Valve
5
Blower Motor Assembly
Circulation Pump
6
7
Internal Flow Valve
8
Front Cover Gasket
9
Water Inlet Fitting (Flange)
Inlet Water Filter
10
11
12
13
Return Fitting (Flange)
Barbed Fitting
Heat Exchanger
54
Download from Www.Somanuals.com. All Manuals Search And Download.
A
E
F
C
D
B
G
T
S
H
R
Q
I
P
O
N
M
L
12
K
J
U
V
W
X
Y
Z
13
1
2
11
10
9
3
4
5
6
8
7
Download from Www.Somanuals.com. All Manuals Search And Download.
55
REPLACEMENT PARTS
DESCRIPTION
KIT #
Drain valve
9000058015
9003741005
9004333005
9006827005
9007173005
9007174005
9007175005
9007176005
9007177005
9007178005
9007179015
9007205005
9007206005
9007207005
9007208005
9007209005
9007210015
9007211015
9007423015
9007424005
9007425005
9007426005
9007427015
9007428015
9007429015
9007430005
9007431015
9007577005
T&P relief valve
Anode/MG/NIP/HT
Anode/AL/NIP/HT
Circulation pump assembly
Inlet/outlet thermistor (Temp sensor)
PCB assembly w/ base
12” Hose (braided)
Tank thermistor
NIP/DIP/TBO/HT
Hi limit 85 (ECO)
Drain/trap assembly-condensate
Heat engine assy
Gas valve
Diptube J 3/4” (return)
Transformer
Hi limit Fuse
Switch-High Temp
Inlet water filter
Water valve assembly
Display assembly with label (English)
Display assembly with label (Bilingual)
PCB fuse
Flame sensor with bracket and gasket
Ignitor (w/ spark generator, bracket and gasket)
Blower motor assembly
Transformer fuse
Heat Exchanger
56
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED RESIDENTIAL GAS WARRANTY
THIS WARRANTY IS APPLICABLE TO THE ORIGINAL OWNER ONLY If
SERVICE AND LABOR RESPONSIBILITY
the glass lined tank in this water heater shall prove upon examination by (the
warrantor) to have leaked during the warranty period in normal residential
use, due to natural corrosion from potable water therein, the warrantor will
furnish the ORIGINAL OWNER a replacement water heater of equivalent
size and current model, or a replacement part for any component part which
fails in normal use, in accordance with the warranty terms and conditions
specified below. THE WATER HEATER REPLACEMENT MODEL OR
PART WILL BE WARRANTED FORONLYTHE UNEXPIRED PORTION OF
THE ORIGINAL WARRANTY The warranty period will be determined by the
original installation date of the water heater. PROOF-OF-PURCHASEAND
PROOF-OF-INSTALLATION ARE NECESSARY TO VALIDATE THIS
WARRANTY This warranty is not transferable.
UNDER THIS LIMITED WARRANTY, THE WARRANTOR WILL
PROVIDE ONLY A REPLACEMENT WATER HEATER OR PART
THEREOF. LABOR IS ALSO INCLUDED FOR 1 YEAR. AFTER THAT
PERIOD THE OWNER IS RESPONSIBLE FOR ALL OTHER COSTS.
Such costs may include but are not limited to:
a. Labor charges for service, removal, or reinstallation of the water heater
or part thereof.
b. Shipping and delivery charges for forwarding the new water heater or
replacement part from the nearest distributor and returning the claimed
defective heater or part to such distributor except in the state of California
where such charges are the manufacturer’s responsibility.
c. All cost necessary or incidental for handling and administrative charges,
and for any materials and/or permits required for installation of the
replacement heater or part.
WARRANTY PERIOD
Product Line
HEAT ENGINE & TANK1
PARTS2
LIMITATION ON IMPLIED WARRANTIES
HYB-90N
6 YEARS
6 YEARS
Implied warranties, including any warranty of merchantability imposed on
the sale of this heater under state law are limited to one year duration for the
heater or any of its parts. Some states do not allow limitations on how long
an implied warranty lasts, so the above limitations may not apply to you.
When the water heater has been used for other than single family residential
application: 1. The Tank warranty shall be reduced to 1 year on 6 year
models. 2. The parts warranty shall be reduced to 1 year for all models.
Returned parts which meet any of the following conditions are not covered
by this warranty: 1) improper installation or removal; 2) damaged by other
than normal wear; 3) replaced for cosmetic purposes; or 4) returned with
defaced date codes.
CLAIM PROCEDURE
Any claim under this warranty should be initiated with the dealer who sold
the heater, or with any other dealer handling the warrantor’s products.
The warrantor will only honor replacement with identical or similar water
heater or parts thereof which are manufactured or distributed by the
warrantor.
CONDITIONS AND EXCEPTIONS
This warranty shall apply only when the water heater is installed and
operated in accordance with: 1) all local fire codes and plumbing codes,
ordinances and regulations; 2) the printed instructions provided with it; 3)
good industry practices; and 4) proper safety practices such as but not
limited to a properly sized drain pan if installed in an area where leakage
from connections of the tank would result in damage to the area adjacent
to the heater. In addition, a new temperature and pressure relief valve,
certified by the Canadian Standards Association must have been properly
installed and piped to the nearest drain.
Dealer replacements are made subject to in-warranty validation by
warrantor.
PROOF-OF-PURCHASE AND PROOF-OF-INSTALLATION DATES ARE
REQUIRED TO SUPPORT WARRANTY FOR CLAIM FROM ORIGINAL
OWNER. THIS FORM DOES NOT CONSTITUTE PROOF-OF-PURCHASE
OR PROOF-OF-INSTALLATION.
This warranty shall apply only when the heater is:
DISCLAIMERS
•
•
owned by the original purchaser;
used at temperatures not exceeding the maximum calibrated setting
of its thermostat;
NO EXPRESS WARRANTY HAS BEEN OR WILL BE MADE IN BEHALF
OF THE WARRANTOR WITH RESPECT TO THE MERCHANTABILITY
OF THE HEATER OR THE INSTALLATION, OPERATION, REPAIR OR
REPLACEMENT OF THE HEATER OR PARTS. THE WARRANTOR SHALL
NOT BE RESPONSIBLE FOR WATER DAMAGE, LOSS OF USE OF THE
UNIT,INCONVENIENCE,LOSSORDAMAGETOPERSONALPROPERTY,
OR OTHER CONSEQUENTIAL DAMAGE. THE WARRANTOR SHALL
NOT BE LIABLE BY VIRTUE OF THIS WARRANTY OR OTHERWISE FOR
DAMAGE TO ANY PERSONS OR PROPERTY, WHETHER DIRECT OR
INDIRECT, AND WHETHER ARISING IN CONTRACT OR IN TORT.
•
•
not subjected to excessive water pressure fluctuations and not subject
to an operating pressure greater than 150 P.S.I.;
filled with potable water, free to circulate at all times and with the tank
free of damaging water sediment or scale deposits;
used in a non-corrosive and non-contaminated atmosphere;
used with factory approved anode(s) installed;
in its original installation location;
in the United States and its territories or possessions or Canada;
sized in accordance with proper sizing techniques for residential
water heaters;
•
•
•
•
•
Some states do not allow the limitation or exclusion of incidental or
consequential damages, so the above limitation or exclusion may not
apply to you.
•
•
•
•
•
•
bearing a rating plate which has not been altered, defaced or removed
except as required by the warrantor;
used in an open system or in a closed system with a properly sized
and installed thermal expansion tank;
fired at the factory rated input using the fuel stated in the face of the
rating plate;
operated with the inner and outer combustion chamber doors in
place;
maintained in accordance with the instructions printed in the manual
included with the heater;
used in a water supply with less than 12 grains per gallon (200 mg/L)
of hardness, is not acidic or otherwise impure.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. Should governmental regulations or
industry standards prohibit the Manufacturer from furnishing a comparable
model replacement under this warranty, the Owner will be furnished with
the closest comparable water heater meeting the current governmental
regulations and industry standards. A supplementary fee may be assessed
to cover the additional cost associated with the changes made to meet
applicable regulations and standards.
Problems resulting from scale formation are not covered by the
warranty.
Any accident to the water heater or any part thereof (including freezing,
fire, floods, or lightning), any misuse, abuse or alteration of it, any
operation of it in a modified form, or any attempt to repair tank leaks or
parts, will void this warranty.
Download from Www.Somanuals.com. All Manuals Search And Download.
57
500 TENNESSEE WALTZ PARKWAY
ASHLAND CITY, TN 37015
PHONE: 1-800-433-2545 FAX: 1-800-433-2515
Download from Www.Somanuals.com. All Manuals Search And Download.
|