Quick Start Guide
UDM-RX01 Endeleo Multi-Format Receiver
Configuration
Overview
The UDM-RX01 is configured via the UDM Hub’s WebConsole. Refer to the UDM
Installed at the display device, the UDM-RX01 (FG-UDM-RX01) converts the signal
received from a UDM Multi-Format Distribution Hub to standard A/V signals (FIG. 1).
Hub’s Operation/Reference Guide for details.
Rear Panel Components
All of the connectors and ports are located on the rear panel (FIG. 2):
Composite (Pr) port
Composite (Pb) port
Composite (Y) port
VGA (HD15) port
S-Video port
CVBS port
UDM HUB port (RJ45) - from an
“OUTPUT” port on the UDM Hub
FIG. 1 UDM-RX01
Serial port (RJ12)
With intelligent receiver technology, each UDM-RX01 is powered directly from the
UDM Multi-Format Distribution Hub. As the hub is switched from one video/audio
source to another, the receiver detects a change in signal and automatically switches
the output device to its new video format.
Compatibility
The UDM-RX01 is compatible for use with the following UDM Hubs:
•
•
•
•
UDM-0102 (FG-UDM-0102)
UDM-0404 (FG-UDM-0404)
UDM-1604 (FG-UDM-1604C)
UDM-1604 (FG-UDM-1604)
IR Rx port
RCA audio
IR Tx port
SPDIF female Digital Audio port
Product Specifications
UDM-RX01 Specifications
FIG. 2 UDM-RX01 - rear panel components
UDM Hub Port (RJ45)
The UDM-RX01 connects to the network through a connection to a UDM Hub. Refer to
the UDM Hub’s Operation/Reference Guide for details.
Power Requirements:
24VDC @ .75A
Note: The UDM-RX01 is remotely powered by the UDM
Serial Port
Rear Panel Connectors:
The Serial port is available for diagnostic and troubleshooting purposes.
The Serial port on the UDM-RX01 is an RJ12 connector, and requires a DB9-to-RJ12
adapter cable (FG-RS01) to connect to a PC for Terminal control.
Power Socket:
2.1mm barrel-style DC power socket (female)
UDM Hub (RJ45)
Port:
Provides audio/video transport as well as control via Cat5,
Cat5e or Cat6 to an UDM Hub.
IR Receiver (IR Rx) Port
The IR Rx port is used to enable user control and the remote compensation of the
video link to the UDM, using the FG-UDM-RC10 and the FG-IR03.
Refer to the Protocols and IR Learning section of the UDM Hub’s Operation/Reference
Guide for details for information on learning a device’s IR commands.
Serial (RJ12) port:
Enables an administrator to control the various functions
to the UDM-RX01 from a command line prompt and termi-
nal connection.
• Requires a DB9-to-RJ12 adapter cable (FG-RS01) to
connect to a PC.
• 9600, 8 bit, No Parity, 1 Stop Bit
IR Transmit (IR Tx) Port
The IR Tx port issues IR commands from the UDM-RX01 to a controlled device. One
IR device (such as DVD player or VCR) can be connected to the UDM-RX01 via the IR
Tx port, and controlled via the UDM Hub’s WebConsole or via remote control.
Note: IR devices controlled via the IRTX ports are typically installed within the same
equipment rack as the UDM Hub and Receiver.
IR Rx Port:
3.5mm stereo input port, for connection of an IR receiver
to allow setup of the UDM-RX01, local compensation
controls, and remote control of centrally located IR
devices.
Connecting an IR Device to the IR Tx Port
IR Tx Port:
3.5mm stereo IR Transmitter output port allows one IR-
controlled device (such as a DVD or VCR player) to be
controlled via optional wired IR emitter.
1.
Connect an IR01 Endeleo IR Emitter Module (FG-IR01) to the IR Tx port on the
UDM-RX01.
Note: Ensure the position of the device corresponds to the position assigned in
the Devices option of the UDM- Hub’s WebConsole.
Run the other end of the IR Emitter cable to the device’s IR sensor, and attach
the IR Emitter to the device’s sensor by removing the cover on the reverse side
of the IR Emitter.
Audio Connectors:
• Black RCA female connector - Digital audio
• White RCA female connector - Analog audio Left
• Red RCA female connector - Analog audio Right
2.
Video Connectors:
• Yellow RCA female connector - CVBS (supports
composite video)
• S-Video - S-video female connector
• VGA - HD15 female connector (supports VGA video)
• Green RCA female connector - Component output: Y
• Blue RCA female connector - Component output: Pb
• Red RCA female connector - Component output: Pr
IR commands for each device on the system have to be learned by the UDM hub in
order to function properly. Refer to the Protocols and IR Learning section of the UDM
Hub’s Operation/Reference Guide for information on learning a device’s IR
commands.
Audio Connectors
The UDM-RX01 provides standard Audio RCA output connectors for S/PDIF for digital
audio, and LEFT/RIGHT for analog audio output (FIG. 2).
Operating Environment: • 35°F - 95°F (5°C - 35°C)
• Max. relative humidity - 85% (non-condensing)
Video Connectors
VGA Input at Display Device
Dimensions (HWD):
Weight:
1" x 8 15/16” x 3 3/8” (25 mm x 227 mm x 85 mm)
1.45 lb. (658 g)
1.
Attach one end of the Endeleo VGA to VGA cable to the VGA connector on the
UDM-RX01.
2.
3.
Run the other end to the VGA connector on the display device. Connect firmly.
If appropriate connect audio to the audio connectors on the UDM-RX01.
Note: Ensure Input A is configured as a “VGA Input” and named appropriately
within the “Inputs” section of the Hub’s Configuration software. Also ensure the
correct Audio Type (Analog L/R or S/PDIF) is selected for the relevant input.
Certifications:
• CE
• FCC part 15 Class A
Other AMX Equipment: • RS232 DB9/RJ12 Connection Cable (FG-RS01)
• UDM-RC02 Multi-Format IR Remote Control
(FG-UDM-RC02)
• IR01 IR Emitter Module (FG-IR01)
• IR03 External IR Receiver Module (FG-IR03)
• UDM-PS 24VDC, 750mA Power Supply (FG-UDM-PS)
Download from Www.Somanuals.com. All Manuals Search And Download.
