ADTRAN Switch ADT 1234POE User Manual

For information on switch configuration for a specific application, refer to the quick configuration documents

provided on the AOS Documentation CD shipped with your base unit. For details on the command line interface

(CLI), refer to the AOS Command Reference Guide (also included on your CD).

NetVanta 1224 Shipping Contents

Each NetVanta 1224 unit is shipped in its own cardboard shipping carton. Open each carton carefully, and avoid

deep penetration into the carton with sharp objects.

After unpacking the unit, inspect it for possible shipping damage. If the equipment has been damaged in transit,

immediately file a claim with the carrier and contact ADTRAN Customer Service (refer to the Repair and

Replacement section of the Support page on the ADTRAN website at http://www.adtran.com/support).

Domestic shipments of the NetVanta 1224 include the following items:

•

NetVanta 1224 base unit

AOS Documentation CD

A detachable power cable with a grounded, three-prong plug

Quick Start Guide

Warranty card

International shipments of the NetVanta 1224 include the following items:

•

NetVanta 1224 base unit

AOS Documentation CD

All necessary power cords

Quick Start Guide

Warranty card

NetVanta 1224 Front Panel Design

The NetVanta 1224 and NetVanta 1224 PoE front panels are shown below. T a ble 1 on page 33 describes all of

the LEDs, and Appendix A on page 67 shows the connector pinouts.

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

NetVanta 1000/1000R Series Hardware Installation Guide

Physical Descriptions

NetVanta 1224 Front Panel Features

10/100BaseT Ethernet Interfaces

The NetVanta 1224s contain 24 10/100BaseT Ethernet interfaces (RJ-45). These interfaces are

consecutively numbered 1 through 24, from left to right, with the numbers screened directly above

each port. Status LEDs for each of these interfaces are located directly over these numbers.

The NetVanta 1224 PoE also has green and red PoE status LEDs located in the upper left and upper

right corners (respectively) of each Ethernet connector.

Status LED

The STAT LED, which indicates the unit’s status, is located to the lower left of RJ-45 port 1.

Figure 1. NetVanta 1224 Front Panel Layout

Figure 2. NetVanta 1224 PoE Front Panel Layout

NetVanta 1224 Rear Panel Design

The NetVanta 1224 and NetVanta 1224 PoE rear panel is shown below. Refer to Appendix A on page 67 for

pinouts.

Figure 3. NetVanta 1224 and NetVanta 1224 PoE Rear Panel Layout

NetVanta 1224 Rear Panel Interfaces

CONSOLE Interface

The CONSOLE interface is an EIA-232 serial port (DCE) that provides for local management and

configuration (via a DB-9 female connector).

Connection directly to an external modem requires a cross-over cable.

Power Connection

The rear panel has a power input to the AC universal power supply. Please refer to Supplying Power to

the Unit on page 56 for connection details.

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

Physical Descriptions

NetVanta 1000/1000R Series Hardware Installation Guide

NetVanta 1224ST

The NetVanta 1224ST and NetVanta 1224ST PoE are managed switches housed in a 1U-high rack-mountable

metal enclosure that includes a universal AC power supply. The front panel contains 24 10/100BaseT Ethernet

interfaces (RJ-45). The NetVanta 1224ST front panel contains two Gigabit Ethernet interfaces that provide two

fixed RJ-45 connectors and two standard SFP slots for fiber connectivity. The NetVanta 1224ST PoE version

provides the ability to detect attached PDs, and deliver 48 VDC to the PDs via existing CAT 5 cabling.

This section includes a list of features, a list of shipping contents, and a description of the unit’s front and rear

panel designs. For additional information, refer to the following sections:

•

For information on switch configuration for a specific application, refer to the quick configuration documents

provided on the AOS Documentation CD shipped with your base unit. For details on the CLI, refer to the AOS

Command Reference Guide (also included on your CD).

NetVanta 1224ST Shipping Contents

Each NetVanta 1224ST unit is shipped in its own cardboard shipping carton. Open each carton carefully, and

avoid deep penetration into the carton with sharp objects.

After unpacking the unit, inspect it for possible shipping damage. If the equipment has been damaged in transit,

immediately file a claim with the carrier and contact ADTRAN Customer Service (refer to the Repair and

Replacement section of the Support page on the ADTRAN website at http://www.adtran.com/support).

Domestic shipments of the NetVanta 1224ST include the following items:

•

NetVanta 1224ST base unit

AOS Documentation CD

A detachable power cable with a grounded, three-prong plug

Quick Start Guide

Warranty card

International shipments of the NetVanta 1224ST include the following items:

•

NetVanta 1224ST base unit

AOS Documentation CD

All necessary power cords

Quick Start Guide

Warranty card

NetVanta 1224ST Front Panel Design

The NetVanta 1224ST and the NetVanta 1224ST PoE front panels are shown below. T able 1 on page 33

describes all of these LEDs, and Appendix A on page 67 shows the connector pinouts.

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

NetVanta 1000/1000R Series Hardware Installation Guide

Physical Descriptions

NetVanta 1224ST Front Panel Features

10/100BaseT Ethernet Interfaces

The NetVanta 1224STs contain 24 10/100BaseT Ethernet interfaces (RJ-45). These interfaces are

consecutively numbered 1 through 24, from left to right, with the numbers screened directly above

each port. Status LEDs for each of these interfaces are located directly over these numbers.

The NetVanta 1224ST PoE also has green and red PoE status LEDs located in the upper left and upper

right corners (respectively) of each Ethernet connector.

Gigabit Ethernet Interfaces/SFP Slots

The NetVanta 1224STs also contain two Gigabit Ethernet interfaces that provide two fixed RJ-45

connectors and two standard SFP slots for fiber connectivity. (Use either the RJ-45 connectors or the

SFP slots. The fiber slots have precedence.) These interfaces are labeled G1 and G2, and their status

LEDs (also labeled G1 and G2) are located to the left of RJ-45 port 1, above the STAT LED.

Status LED

The STAT LED, which indicates the unit’s status, is located to the lower left of RJ-45 port 1.

Figure 4. NetVanta 1224ST Front Panel Layout

Figure 5. NetVanta 1224ST PoE Front Panel Layout

NetVanta 1224ST Rear Panel Design

The NetVanta 1224ST and NetVanta 1224ST PoE rear panel is shown below. Refer to Appendix A on page 67

for pinouts.

Figure 6. NetVanta 1224ST and NetVanta 1224ST PoE Rear Panel Layout

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

Physical Descriptions

NetVanta 1000/1000R Series Hardware Installation Guide

NetVanta 1224ST Rear Panel Interfaces

CONSOLE Interface

The CONSOLE interface is an EIA-232 serial port (DCE) that provides for local management and

configuration (via a DB-9 female connector).

Connection directly to an external modem requires a cross-over cable.

Power Connection

The rear panel has a power input to the AC universal power supply. Please refer to Supplying Power to

the Unit on page 56 for connection details.

NetVanta 1224R

The NetVanta 1224R and NetVanta 1224R PoE are managed switches housed in a 1U-high rack-mountable

metal enclosure that includes a universal AC power supply. The front panel contains 24 10/100BaseT Ethernet

interfaces (RJ-45). The NetVanta 1224R PoE version provides the ability to detect attached PDs, and deliver

48 VDC to the PDs via existing CAT 5 cabling. Both units contain a single network interface module (NIM) slot

on the rear panel to support the following modules:

•

1200861L1

1202862L1

1202863L1

1200872L1

1200868E1/L1

1200878E1/L1

1200866E1

1200936E1

1200937E1

1202869E1

1202889E1

1200864L1

1200865L1

1200875L1

56K/64K NIM

T1/FT1 NIM

T1/FT1 + DSX-1 NIM

Dual T1 NIM

E1/FE1 NIM

E1/FE1 + G.703 Drop NIM

Serial Interface Module

SHDSL NIM, Annex A

SHDSL NIM, Annex B

ADSL NIM, Annex A

ADSL NIM, Annex B

Analog Modem DIM

ISDN BRI DIM

ISDN S/T DIM

This section includes a list of features, a list of shipping contents, and a description of the unit’s front and rear

panel designs. For additional information, refer to the following sections:

•

For information on router configuration for a specific application, refer to the quick configuration documents

provided on the AOS Documentation CD shipped with your base unit. For details on the CLI, refer to the AOS

Command Reference Guide (also included on your CD).

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

NetVanta 1000/1000R Series Hardware Installation Guide

Physical Descriptions

NetVanta 1224R Shipping Contents

Each NetVanta 1224R and NetVanta 1224R PoE unit is shipped in its own cardboard shipping carton. Open each

carton carefully, and avoid deep penetration into the carton with sharp objects.

After unpacking the unit, inspect it for possible shipping damage. If the equipment has been damaged in transit,

immediately file a claim with the carrier and contact ADTRAN Customer Service (refer to the Repair and

Replacement section of the Support page on the ADTRAN website at http://www.adtran.com/support).

Domestic shipments of the NetVanta 1224R include the following items:

•

NetVanta 1224ST base unit

AOS Documentation CD

A detachable power cable with a grounded, three-prong plug

Quick Start Guide

Warranty card

International shipments of the NetVanta 1224R include the following items:

•

NetVanta 1224ST base unit

AOS Documentation CD

All necessary power cords

Quick Start Guide

Warranty card

NetVanta 1224R Front Panel Design

The NetVanta 1224R and the NetVanta 1224R PoE front panels are shown below. T able 1 on page 33 describes

all of these LEDs, and Appendix A on page 67 shows the connector pinouts.

NetVanta 1224R Front Panel Features

10/100BaseT Ethernet Interfaces

The NetVanta 1224R and the NetVanta 1224R PoE contain 24 10/100BaseT Ethernet interfaces (RJ-45).

These interfaces are consecutively numbered 1 through 24, from left to right, with the numbers

screened directly above each port. Status LEDs for each of these interfaces are located directly over

these numbers.

The NetVanta 1224R PoE also has green and red PoE status LEDs located in the upper left and upper

right corners (respectively) of each of the Ethernet connectors.

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

Physical Descriptions

NetVanta 1000/1000R Series Hardware Installation Guide

Status LEDs

The status LEDs are located to the lower left of RJ-45 port 1. The WAN LED reflects the status of an

installed NIM. The DBU LED reflects the status of an installed dial backup interface module (DIM).

The STAT LED indicates the unit’s status.

Figure 7. NetVanta 1224R Front Panel Layout

Figure 8. NetVanta 1224R PoE Front Panel Layout

NetVanta 1224R Rear Panel Design

The NetVanta 1224R and NetVanta 1224R PoE rear panel is shown below. Refer to Appendix A on page 67 for

pinouts.

Figure 9. NetVanta 1224R and NetVanta 1224R PoE Rear Panel Layout

NetVanta 1224R Rear Panel Interfaces

NIM Option Slot

The NIM option slot accepts a variety of NIM option modules (refer to Option Modules on page 35).

CONSOLE Interface

The CONSOLE interface is an EIA-232 serial port (DCE) that provides for local management and

configuration (via a DB-9 female connector).

Connection directly to an external modem requires a cross-over cable.

Power Connection

The rear panel has a power input to the AC universal power supply. Please refer to Supplying Power to

the Unit on page 56 for connection details.

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

NetVanta 1000/1000R Series Hardware Installation Guide

Physical Descriptions

NetVanta 1224STR

The NetVanta 1224STR (AC and DC versions) and NetVanta 1224STR PoE are managed switches housed in a

1U-high rack-mountable metal enclosure that includes either a universal AC or a DC power supply. The

NetVanta 1224STR PoE version provides the ability to detect attached PDs, and deliver 48 VDC to the PDs via

existing CAT 5 cabling. Both front panels contain 24 10/100BaseT Ethernet interfaces (RJ-45). The NetVanta

1224STR front panel contains one Gigabit Ethernet interface that provides one fixed RJ-45 connector and one

standard SFP slot for fiber connectivity. The NetVanta 1224STR PoE front panel contains two Gigabit Ethernet

interfaces and two standard SFP slots. Both units contain a single NIM slot on the rear panel to support the

following modules:

•

1200861L1

1202862L1

56K/64K NIM

T1/FT1 NIM

1200862L2#NEBS T1/FT1 NEBS NIM (NetVanta 1224STR PoE only)

1202863L1

1200872L1

1200868E1/L1

1200878E1/L1

1200866E1

1200936E1

1200937E1

1202869E1

1202889E1

1200864L1

1200865L1

1200875L1

T1/FT1 + DSX-1 NIM

Dual T1 NIM

E1/FE1 NIM

E1/FE1 + G.703 Drop NIM

Serial Interface Module

SHDSL NIM, Annex A

SHDSL NIM, Annex B

ADSL NIM, Annex A

ADSL NIM, Annex B

Analog Modem DIM

ISDN BRI DIM

ISDN S/T DIM

This section includes a list of features, a list of shipping contents, and a description of the unit’s front and rear

panel designs. For additional information, refer to the following sections:

•

For information on router configuration for a specific application, refer to the quick configuration documents

provided on the AOS Documentation CD shipped with your base unit. For details on the CLI, refer to the AOS

Command Reference Guide (also included on your CD).

NetVanta 1224STR Shipping Contents

Each NetVanta 1224STR and NetVanta 1224STR PoE units are shipped in their own cardboard shipping

cartons. Open each carton carefully, and avoid deep penetration into the carton with sharp objects.

After unpacking the unit, inspect it for possible shipping damage. If the equipment has been damaged in transit,

immediately file a claim with the carrier and contact ADTRAN Customer Service (refer to the Repair and

Replacement section of the Support page on the ADTRAN website at http://www.adtran.com/support).

Domestic shipments of the NetVanta 1224STR include the following items:

•

NetVanta 1224STR base unit

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

Physical Descriptions

NetVanta 1000/1000R Series Hardware Installation Guide

•

AOS Documentation CD

•

A detachable power cable with a grounded, three-prong plug

Quick Start Guide

Warranty card

International shipments of the NetVanta 1224STR include the following items:

•

NetVanta 1224STR base unit

AOS Documentation CD

All necessary power cords

Quick Start Guide

Warranty card

NetVanta 1224STR Front Panel Design

The NetVanta 1224STR and the NetVanta 1224STR PoE front panels are shown below. T able 1 on page 33

describes all of the LEDs, and Appendix A on page 67 shows the connector pinouts.

NetVanta 1224STR Front Panel Features

10/100BaseT Ethernet Interfaces

The NetVanta 1224STRs contain 24 10/100BaseT Ethernet interfaces (RJ-45). These interfaces are

consecutively numbered 1 through 24, from left to right, with the numbers screened directly above

each port. Status LEDs for each of these interfaces are located directly over these numbers.

The NetVanta 1224STR PoE also has green and red PoE status LEDs located in the upper left and

upper right corners (respectively) of each Ethernet connector.

Gigabit Ethernet Interfaces/SFP Slots

The NetVanta 1224STR front panel contains one Gigabit Ethernet interface that provides one fixed

RJ-45 connector and one standard SFP slot for fiber connectivity. (Use either the RJ-45 connector or

the SFP slot. The fiber slot has precedence.) This interface is labeled G1, and the status LED is located

to the left of RJ-45 port 1, above the STAT LED.

The NetVanta 1224STR PoE front panel contains two Gigabit Ethernet interfaces and two standard

SFP slots. (Use either the RJ-45 connectors or the SFP slots. The fiber slots have precedence.) These

interfaces are labeled G1 and G2, and the status LEDs are located above the SFP slots.

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

NetVanta 1000/1000R Series Hardware Installation Guide

Physical Descriptions

Status LEDs

The status LEDs are located to the lower left of RJ-45 port 1. The WAN LED reflects the status of an

installed NIM. The DBU LED reflects the status of an installed DIM. The STAT LED indicates the

unit’s status.

Figure 10. NetVanta 1224STR (AC) Front Panel Layout

Figure 11. NetVanta 1224STR (DC) Front Panel Layout

Figure 12. NetVanta 1224STR PoE Front Panel Layout

NetVanta 1224STR Rear Panel Design

The NetVanta 1224STR and NetVanta 1224STR PoE rear panels are shown below. Refer to Appendix A on page

67 for pinouts.

Figure 13. NetVanta 1224STR (AC) and NetVanta 1224STR PoE Rear Panel Layout

USE COPPER

WAN-T1

CONDUCTORS ONLY

-48V....., 1.2A

+24V....., 2.5A

Figure 14. NetVanta 1224STR (DC) Rear Panel Layout

NetVanta 1224STR Rear Panel Interfaces

NIM Option Slot

The NIM option slot accepts a variety of NIM option modules (refer to Option Modules on page 35).

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

Physical Descriptions

NetVanta 1000/1000R Series Hardware Installation Guide

CONSOLE Interface

The CONSOLE interface is an EIA-232 serial port (DCE) that provides for local management and

configuration (via a DB-9 female connector).

Connection directly to an external modem requires a cross-over cable.

Power Connection

The rear panel of the NetVanta 1224STR (AC) and NetVanta 1224STR PoE have a power input for

connection to an AC universal power supply. The NetVanta 1224STR (DC) connects to a centralized

DC power source via a four-position power connector. Please refer to Supplying Power to the Unit on

page 56 for connection details.

NetVanta 1335

All NetVanta 1335 Series units are managed switches, plus multiservice routers housed in a 1U-high

rack-mountable metal enclosure that includes a universal AC power supply. The NetVanta 1335 PoE and

NetVanta 1335 WiFi PoE provide the ability to detect attached PDs, and deliver 48 VDC to the PDs via existing

CAT 5 cabling. The NetVanta 1335 WiFi Series units operate as wireless bridges for local area networks

(LANs). A dual radio design with two dual-band external antennas is used to support concurrent 802.11a and

802.11b/g connections. The NetVanta 1335 Series front panels contain 24 10/100BaseT Ethernet interfaces and

two Gigabit Ethernet interfaces accessed via a fixed RJ-45 connector or SFP slots for fiber connectivity. The

NetVanta 1335 WiFi Series front panels contain 24 10/100BaseT Ethernet interfaces and one Gigabit Ethernet

interface accessed via a fixed RJ-45 connector or SFP slot. All NetVanta 1335 Series units include IPSec VPN

support (without further software upgrades) and expandable memory via CompactFlash and SODIMM slots.

NetVanta 1335 Series units also contain one NIM slot on the rear panel to support the following modules in data

applications:

•

1200861L1

1202862L1

1202863L1

1200872L1

1200868E1/L1

1200878E1/L1

1200866E1

1200936E1

1200937E1

1202869E1

1202889E1

1700801G1

1200864L1

1200865L1

1200875L1

56K/64K NIM

T1/FT1 NIM

T1/FT1 + DSX-1 NIM

Dual T1 NIM

E1/FE1 NIM

E1/FE1 + G.703 Drop NIM

Serial Interface Module

SHDSL NIM, Annex A

SHDSL NIM, Annex B

ADSL NIM, Annex A

ADSL NIM, Annex B

3G CDMA NIM, 1xRTT, 1xEV-DO Revision 0, 1xEV-DO Revision A

Analog Modem DIM

ISDN BRI DIM

ISDN S/T DIM

This section includes a list of features, a list of shipping contents, and a description of the front and rear panel

designs. For additional information, refer to the following sections:

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

NetVanta 1000/1000R Series Hardware Installation Guide

Physical Descriptions

•

For information on router configuration for a specific application, refer to the quick configuration documents

provided on the AOS Documentation CD shipped with your base unit. For details on the CLI, refer to the AOS

Command Reference Guide (also included on your CD).

NetVanta 1335 Shipping Contents

Each NetVanta 1335 unit is shipped in its own cardboard shipping carton. Open each carton carefully, and avoid

deep penetration into the carton with sharp objects.

After unpacking the unit, inspect it for possible shipping damage. If the equipment has been damaged in transit,

immediately file a claim with the carrier and contact ADTRAN Customer Service (refer to the Repair and

Replacement section of the Support page on the ADTRAN website at http://www.adtran.com/support).

Domestic shipments of the NetVanta 1335 include the following items:

•

NetVanta 1335 base unit

AOS Documentation CD

Two dual-band RP-SMA detachable antennas (NetVanta 1335 WiFi and NetVanta 1335 WiFi PoE only)

A detachable power cable with a grounded, three-prong plug

Quick Start Guide

Warranty card

International shipments of the NetVanta 1335 include the following items:

•

NetVanta 1335 base unit

AOS Documentation CD

Two dual-band RP-SMA detachable antennas (NetVanta 1335 WiFi and NetVanta 1335 WiFi PoE only)

All necessary power cords

Quick Start Guide

Warranty card

NetVanta 1335 Front Panel Design

The NetVanta 1335 Series front panels are shown on page 29. T able 1 on page 33 describes all of the LEDs,

and Appendix A on page 67 shows the connector pinouts.

NetVanta 1335 Front Panel Features

10/100BaseT Ethernet Interfaces

The NetVanta 1335 Series units contain 24 10/100BaseT Ethernet interfaces (RJ-45). These interfaces

are consecutively numbered 1 through 24, from left to right, with the numbers screened directly above

each port. Status LEDs for each of these interfaces are located directly over these numbers.

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

Physical Descriptions

NetVanta 1000/1000R Series Hardware Installation Guide

Gigabit Ethernet Interfaces/SFP Slots

The NetVanta 1335 and NetVanta 1335 PoE contain two Gigabit Ethernet interfaces that provide two

fixed RJ-45 connectors and two standard SFP slots for fiber connectivity. These interfaces are labeled

G1 and G2, and the status LEDs are located above the SFP slots. The NetVanta 1335 WiFi and

NetVanta 1335 WiFi PoE contain one Gigabit Ethernet interface that provides one fixed RJ-45

connector and one standard SFP slot for fiber connectivity. This interface is labeled G1, and the status

LED is located above the SFP slot. (Use either the RJ-45 connector or the SFP slot. The fiber slot has

precedence.)

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

NetVanta 1000/1000R Series Hardware Installation Guide

Physical Descriptions

Status LEDs

The status LEDs are located to the lower left of RJ-45 port 1. The WLAN LED (NetVanta 1335 WiFi

Series only) reflects the status of the wireless network. The WAN LED reflects the status of an installed

NIM. The DBU LED reflects the status of an installed DIM. The STAT LED indicates the unit’s status.

Figure 15. NetVanta 1335 Front Panel Layout

NetVanta 1335

Figure 16. NetVanta 1335 PoE Front Panel Layout

Figure 17. NetVanta 1335 WiFi Front Panel Layout

Figure 18. NetVanta 1335 WiFi PoE Front Panel Layout

NetVanta 1335 Rear Panel Design

The NetVanta 1335 Series rear panels are shown below. Refer to Appendix A on page 67 for pinouts.

WAN-T1

DSX-1

DBU

Figure 19. NetVanta 1335 and NetVanta 1335 PoE Rear Panel Layout

WAN-T1

DSX-1

DBU

Figure 20. NetVanta 1335 WiFi and NetVanta 1335 WiFi PoE Rear Panel Layout

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

Physical Descriptions

NetVanta 1000/1000R Series Hardware Installation Guide

NetVanta 1335 Rear Panel Interfaces

NIM Option Slot

The NIM option slot accepts a variety of NIM option modules (refer to Option Modules on page 35).

CompactFlash

The CompactFlash slot supplies nonvolatile configuration and compressed code storage. The NetVanta

1335 supports only ADTRAN-provided CompactFlash (16 MB to 1 GB) (refer to the part number on

the front cover of this manual).

CONSOLE Interface

The CONSOLE interface is an EIA-232 serial port (DCE) that provides for local management and

configuration (via a DB-9 female connector).

Connection directly to an external modem requires a cross-over cable.

Antenna Connectors

The ANT 1 and ANT 2 ports (NetVanta 1335 WiFi and NetVanta 1335 WiFi PoE only) support two

dual-band antennas for concurrent 802.11a and 802.11b/g connections.

Power Connection

The rear panel has a power input to the AC universal power supply. Please refer to Supplying Power to

the Unit on page 56 for connection details.

NetVanta 1524ST

The NetVanta 1524ST is a Layer 2 managed switch housed in a 1U-high rack-mountable metal enclosure that

includes a universal AC power supply. The front panel contains 24 10/100/1000BaseT Ethernet interfaces that

are accessed via standard RJ-45 connectors. Four of these twenty-four interfaces can be used in either copper or

fiber mode. Four industry standard SFP slots (supporting industry standard SFP modules) are available for

high-speed uplink or stacking requirements. The switch is managed through an EIA-232 CONSOLE port

(DB-9).

This section includes a list of features, a list of shipping contents, and a description of the unit’s front and rear

panel designs. For additional information, refer to the following sections:

•

NetVanta 56K/64K NIM (P/N 1200861L1) on page 36

For information on switch configuration for a specific application, refer to the quick configuration documents

provided on the AOS Documentation CD shipped with your base unit. For details on the CLI, refer to the AOS

Command Reference Guide (also included on your CD).

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

NetVanta 1000/1000R Series Hardware Installation Guide

Physical Descriptions

NetVanta 1524ST Shipping Contents

Each NetVanta 1524ST unit is shipped in its own cardboard shipping carton. Open each carton carefully, and

avoid deep penetration into the carton with sharp objects.

After unpacking the unit, inspect it for possible shipping damage. If the equipment has been damaged in transit,

immediately file a claim with the carrier and contact ADTRAN Customer Service (refer to the Repair and

Replacement section of the Support page on the ADTRAN website at http://www.adtran.com/support).

Domestic shipments of the NetVanta 1524ST include the following items:

•

NetVanta 1524ST base unit

AOS Documentation CD

A detachable power cable with a grounded, three-prong plug

Quick Start Guide

Warranty card

International shipments of the NetVanta 1524ST include the following items:

•

NetVanta 1524ST base unit

AOS Documentation CD

All necessary power cords

Quick Start Guide

Warranty card

NetVanta 1524ST Front Panel Design

The NetVanta 1524ST front panel is shown below. T a ble 1 on page 33 describes all of the LEDs, and

Appendix A on page 67 shows the connector pinouts.

NetVanta 1524ST Front Panel Features

10/100/1000BaseT Ethernet Interfaces

The NetVanta 1524ST front panel contains 24 10/100/1000BaseT Ethernet interfaces (RJ-45). These

interfaces are consecutively numbered 1 through 24, from left to right, with the numbers screened

directly above each port. Status LEDs for each of these interfaces are located directly over these

numbers.

SFP Slots

The NetVanta 1524ST front panel contains four standard SFP slots for fiber connectivity. These

interfaces are numbered 21 through 24. Status LEDs for each of these slots are located directly over

these numbers.

Status LEDs

The status LEDs are located to the lower left of RJ-45 port 1. The STK LED indicates whether the unit

is a member of a stack. The STAT LED indicates the unit’s status.

Figure 21. NetVanta 1524ST Front Panel Layout

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

Physical Descriptions

NetVanta 1000/1000R Series Hardware Installation Guide

NetVanta 1524ST Rear Panel Design

The NetVanta 1524ST rear panel is shown below. Refer to Appendix A on page 67 for pinouts.

Figure 22. NetVanta 1524ST Rear Panel Layout

NetVanta 1524ST Rear Panel Interfaces

10/100BaseT Ethernet Interface

The Ethernet port (ETH 0/0) is an RJ-45 connector. The Ethernet port provides the following:

• 10BaseT or 100BaseT with a single connector

• Auto-negotiation

• CSMA/CD

• IEEE 802.3 compatibility

CONSOLE Interface

The CONSOLE interface is an EIA-232 serial port (DCE) that provides for local management and

configuration (via a DB-9 female connector).

Connection directly to an external modem requires a cross-over cable.

Power Connection

The rear panel has a power input to the AC universal power supply. Please refer to Supplying Power to

the Unit on page 56 for connection details.

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

NetVanta 1000/1000R Series Hardware Installation Guide

Physical Descriptions

Table 1. Front Panel LED Descriptions

Color Indication

LED

STAT

Off

Unit is not receiving power.

Green (solid)

Green (flashing)

Power is on and self-test passed.

On power-up the STAT LED flashes rapidly for five

seconds, during which time the user may escape to boot

mode from the CONSOLE port.

Red (solid)

Power is on, but the self-test failed or the boot code could

not be booted.

STK (1524ST only)

Off

Unit is not a member of a stack.

Unit is a member of a stack.

Green (solid)

Off

Port LEDs

(i.e., 1 through 24, G1,

G2, etc.)

Port is administratively disabled or does not have a

connection.

Green (solid)

Amber (flashing)

Off

Port is enabled and has a connection.

Port has activity (transmit or receive).

No DIM is installed.

DBU

(1224R, 1224STR, and

1335 only)

Green (solid)

DIM is ready. For the ISDN BRI DIM, green solid indicates

that the negotiation with the switch is complete.

Green (flashing)

Amber (solid)

Red (solid)

Unit is in dial backup.

Unit is in test.

Alarm condition is occurring on the DBU interface, or there

is a self-test failure.

WAN

(1224R, 1224STR, and

1335 only)

Off

No NIM is installed, or interface is administratively down.

NIM is up and everything is operational.

Port has activity (transmit or receive).

Unit is in test.

Green (solid)

Green (flashing)

Amber (solid)

Red (solid)

Alarm condition is occurring on the WAN interface, or there

is a self-test failure.

Power over Ethernet Green (solid)

Power is being applied (48 V) to the interface.

Fault is detected on the interface.

Status LEDs

Red (solid)

(PoE units only)

WLAN

(1335 WiFi and

1335 WiFi PoE)

Off

WLAN is inactive or disabled.

Green (solid)

Amber (flashing)

WLAN card is enabled and active.

Activity (transmit or receive) is detected on the WLAN.

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

Product Specifications

NetVanta 1000/1000R Series Hardware Installation Guide

3. PRODUCT SPECIFICATIONS

Physical Interfaces

10/100BaseT Ethernet interfaces on the front panel

1000BaseT Gigabit Ethernet interfaces on the front panel

(SFP slots for fiber connectivity/RJ-45 connectors for

copper connectivity)

Integrated DB-9, EIA-232 console port (DCE) on the rear

panel

Modular network interface on the rear panel

N/A

Stacking

Spanning Tree Support (802.1D and 802.1w)

Link Aggregation (802.3ad)

VLAN Support (802.1Q), up to 255 active VLANs

Priority QoS (802.1p)

Management

Console

Telnet CLI

SSH CLI

SNMP V2

Port mirroring

Power

AC Power: 100 to 250 VAC, 50/60 Hz

DC Power: 24 to 48 VDC

Mechanical Specifications

Housing: 1U-high metal enclosure

(1.72-inch H x 17.22-inch W x 7.8-inch D) (The 1224STR

PoE and 1335 PoE Series are 12.8-inches deep.)

10/100BaseT Ethernet: 24 ganged RJ-45 jacks

10/100/1000BaseT Ethernet: SFP slots/standard RJ-45

jacks

Console Port: DB-9, female

Dual-band Antenna Connections

CompactFlash

Environmental Specifications

AC Input Power: 100 to 250 VAC

DC Input Power: 24 to 48 VDC at 2.5 A

Storage Temperature: -20°C to 70°C

Operating Temperature: 0°C to 50°C

Relative Humidity: Up to 95 percent, noncondensing

Download from Www.Somanuals.com. All Manuals Search And Download.

61200500L1-34N

NetVanta 1000/1000R Series Hardware Installation Guide

Option Modules

OPTION MODULES

The NetVanta 1224STR, 1224R, and 1335 support several option modules designed to meet a variety of

networking requirements. The option modules include plug-in NIMs and plug-on DIMs.

NIMs are cards that plug directly into the option module slot located on the rear of the base unit. These cards

provide the following types of interfaces:

•

NetVanta T1/FT1 NIM (P/N 1202862L1) on page 37

NetVanta T1/FT1 NEBS NIM (P/N 1200862L2#NEBS) on page 38

NetVanta T1/FT1 + DSX-1 NIM (P/N 1202863L1) on page 39

NetVanta Dual T1 NIM (P/N 1200872L1) on page 40

NetVanta E1/FE1 NIM (P/N 1200868E1/L1) on page 41

NetVanta E1/FE1 + G.703 Drop NIM (P/N 1200878E1/L1) on page 42

NetVanta Serial NIM (P/N 1200866E1) on page 43

NetVanta SHDSL NIM, Annex A (P/N 1200936E1) on page 44

NetVanta SHDSL NIM, Annex B (P/N 1200937E1) on page 45

NetVanta ADSL NIM, Annex A (P/N 1202869E1) on page 46

NetVanta ADSL NIM, Annex B (P/N 1202889E1) on page 47

NetVanta 3G CDMA NIM (P/N 1700801G1) on page 48

DIMs are plug-on cards that plug directly on to the NIM prior to installation into the base unit. A DIM must be

plugged on to a NIM in order for the interfaces on the NIM to be active. The NetVanta supports the following

DIMs:

•

NetVanta Analog Modem DIM (P/N 1200864L1) on page 50

NetVanta ISDN BRI DIM (P/N 1200865L1) on page 51

NetVanta ISDN S/T DIM (P/N 1200875L1) on page 52

This section describes each module, providing individual card specifications and features. Refer to Connector

Pin Definitions on page 67 for pinout information. Installing Dial Backup and Network Interface Modules on

page 57 provides information on card installation.

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

Option Modules

NetVanta 1000/1000R Series Hardware Installation Guide

Network Interface Modules

NetVanta 56K/64K NIM (P/N 1200861L1)

The 56K/64K NIM (shown in Figure 23) provides a DDS WAN interface for the NetVanta. This module

provides a single 56K or 64K DDS network interface. See T a ble A-5 on page 69 for the WAN-DDS connector

pinouts, and page 73 for the DBU connector pinouts. An optional DIM is required for dial backup applications.

Figure 23. NetVanta 56K/64K NIM

Features and Specifications

Operating Modes

Compliance

•

Dedicated DDS (leased line)

•

ACTA/FCC Part 68

IC CS-03

DDS Interface

•

Supported Standards: AT&T TR 62310

4-wire, full-duplex

Receiver Sensitivity: -45 dB, all rates

Data Rates: 56K, 64K, and auto

Connector: RJ-48S

UL/CUL 60950

Environmental

•

Operating Temperature: 0°C to 50°C

Storage Temperature: -20°C to 70°C

Relative Humidity: Up to 95 percent,

noncondensing

Clock Source

•

Network

Internal

Physical

Diagnostics

•

Dimensions: 2.75-inch W x 4.25-inch D

•

CSU and DSU Loopbacks

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

NetVanta 1000/1000R Series Hardware Installation Guide

Option Modules

NetVanta T1/FT1 NIM (P/N 1202862L1)

The T1/FT1 NIM (shown in Figure 24) provides a T1 WAN interface for the NetVanta. This module provides a

full T1 or fractional T1 network interface. See T able A-6 on page 69 for the WAN-T1 connector pinouts, and

page 73 for the DBU connector pinouts. An optional DIM is required for dial backup applications.

WAN-T1

DBU

Figure 24. NetVanta T1/FT1 NIM

Features and Specifications

Operating Modes

Diagnostics

•

Frame Relay, Multilink Frame Relay

PPP, Multilink PPP

HDLC

•

Test Pattern Generation and Detection:

511, QRSS, all ones, all zeros

Network loopbacks (local and remote);

responds to both inband and FDL loop

codes

Alarm generation and detection

Network and user sets of performance data

(15 minutes and 24 hours)

•

T1/FT1 Interface

•

Supported Standards: AT&T TR 62411,

AT&T TR 65016, ANSI T1.403,

Bellcore TR 194

Line Rate: 1.544 Mbps +75 bps

Line Code: AMI or B8ZS

Framing: D4 (SF) or ESF

FT1 Line Rate: DS0 channelized (multiples

of 64 kbps)

Input Signal: 0 to -36 dB (DS1)

Line Build-Out: 0, -7.5, -15, -22.5 dB

(long), 0 to 655 ft (short)

DS0 Assignment: Programmable

Connector: RJ-48C

•

Compliance

•

ACTA/FCC Part 68

IC CS-03

•

UL/CUL 60950

Environmental

•

Operating Temperature: 0°C to 50°C

Storage Temperature: -20°C to 70°C

Relative Humidity: Up to 95 percent,

noncondensing

Clock Source

•

Network

Internal

Physical

•

Dimensions: 2.75-inch W x 4.25-inch D

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

Option Modules

NetVanta 1000/1000R Series Hardware Installation Guide

NetVanta T1/FT1 NEBS NIM (P/N 1200862L2#NEBS)

The T1/FT1 NEBS NIM (see Figure 25) T1 WAN interface for the NetVanta 1224STR DC. The T1 NEBS NIM

is NEBS Level 3 compliant, and provides a full T1 or fractional T1 network interface. See T a ble A-6 on page 69

for the WAN-T1 connector pinouts.

Although the T1/FT1 NEBS NIM is compliant with NEBS Level 3, the NetVanta 1224STR

DC unit supports only NEBS Level 1.

WAN-T1

Figure 25. NetVanta T1/FT1 NEBS NIM

Features and Specifications

Operating Modes

Diagnostics

•

Frame Relay, Multilink Frame Relay

PPP, Multilink PPP

HDLC

•

Test Pattern Generation and Detection:

QRSS, 511, 2¹⁵- 1, 2²⁰- 1, all ones,

all zeros

•

Network loopbacks (local and remote);

responds to inband and FDL loop codes

Alarm generation and detection

Network and user sets of performance data

(15 minutes and 24 hours)

T1/FT1 Interface

•

Supported Standards: AT&T TR 62411,

AT&T TR 65016, ANSI T1.403,

Bellcore TR 194

•

Line Rate: 1.544 Mbps +75 bps

Line Code: AMI or B8ZS

Framing: D4 (SF) or ESF

FT1 Line Rate: DS0 channelized (multiples

of 64 kbps)

Compliance

•

NEBS Level 3

GR-63-CORE

GR-1089-CORE

UL/CUL 60950

•

Input Signal: 0 to -36 dB (DS1)

Line Build-Out: 0, -7.5, -15, -22.5 dB

(long), 0 to 655 ft (short)

•

DS0 Assignment: Programmable

Connector: RJ-48C

Environmental

•

Operating Temperature: 0°C to 50°C

Clock Source

•

Storage Temperature: -20°C to 70°C

Relative Humidity: Up to 95 percent,

noncondensing

Network

Internal

Physical

•

Dimensions: 2.75-inch W x 4.25-inch D

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

NetVanta 1000/1000R Series Hardware Installation Guide

Option Modules

NetVanta T1/FT1 + DSX-1 NIM (P/N 1202863L1)

The T1/FT1 + DSX-1 NIM (see Figure 26) provides a T1 WAN interface for the NetVanta, a full or fractional

T1 network interface, and a DSX-1 interface. See the pinouts in T able A-6 on page 69 for the WAN-T1

connector, T a ble A-8 on page 70 for the DSX-1 connector , and page 73 for the DBU connector pinouts. An

optional DIM is required for dial backup applications.

WAN-T1

DSX-1

DBU

Figure 26. NetVanta T1/FT1 + DSX-1 NIM

Features and Specifications

Operating Modes

Clock Source

•

Frame Relay, Multilink Frame Relay

PPP, Multilink PPP

HDLC

•

Network

Internal

Through

T1/FT1 Interface

Diagnostics

•

Supported Standards: AT&T TR 62411,

AT&T TR 65016, ANSI T1.403,

Bellcore TR 194

Line Rate: 1.544 Mbps +75 bps

Line Code: AMI or B8ZS

Framing: D4 (SF) or ESF

FT1 Line Rate: DS0 channelized (multiples

of 56/64 kbps)

•

Test Pattern Generation and Detection:

511, QRSS, all ones, all zeros

Network loopbacks (local and remote);

responds to inband and FDL loop codes (T1

interface only)

Alarm generation and detection

Network and user sets of performance data

(15 minutes and 24 hours)

•

Input Signal: 0 to -36 dB (DS1)

Line Build-Out: 0, -7.5, -15, -22.5 dB

(long), 0 to 655 ft (short)

DS0 Assignment: Programmable

Connector: RJ-48C

Compliance

•

ACTA/FCC Part 68

IC CS-03

•

UL/CUL 60950

DSX-1 Interface

•

Line Interface: DSX-1 per ANSI T1.102

DSX Receiver Input Range: -10 dBdsx to

+6 dBdsx

Line Rate: 1.544 Mbps

Capacity: 1 to 24 DS0s

Line Codes: AMI, B8ZS

DSX-1 Interface to PBX

Framing: D4 (SF) or ESF

Line Length: 0 to 655 feet and -7.5 dB

Connector: RJ-48C

Environmental

•

Operating Temperature: 0°C to 50°C

Storage Temperature: -20°C to 70°C

Relative Humidity: Up to 95 percent,

noncondensing

•

Physical

•

Dimensions: 2.75-inch W x 4.25-inch D

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

Option Modules

NetVanta 1000/1000R Series Hardware Installation Guide

NetVanta Dual T1 NIM (P/N 1200872L1)

The NetVanta Dual T1 NIM (see Figure 27) provides two T1 WAN interfaces for the NetVanta. See T able A-6

on page 69 for the pinouts. See page 73 for the DBU connector pinouts. An optional DIM is required for dial

backup applications.

WAN T1/1 WAN T1/2

DBU

Figure 27. NetVanta Dual T1 NIM

Features and Specifications

Operating Modes

Diagnostics

•

Frame Relay, Multilink Frame Relay

PPP, Multilink PPP

HDLC

•

Test Pattern Generation and Detection:

QRSS, 511, 2¹⁵- 1, 2²⁰- 1, all ones,

all zeros

•

Network loopbacks (local and remote);

responds to both inband and FDL loop

codes

Alarm generation detection

Network performance data (15 minutes

and 24 hours)

T1 Interface

•

Supported Standards: AT&T TR 62411,

AT&T TR 65016, ANSI T1.403,

Bellcore TR 194

•

Line Rate: 1.544 Mbps +75 bps

Line Code: AMI or B8ZS

Framing: D4 (SF) or ESF

FT1 Line Rate: DS0 channelized

(multiples of 64 kbps)

Compliance

•

EMC - see Electromagnetic

ACTA/FCC Part 68

IC CS-03

•

Input Signal: 0 to -36 dB (DS1)

Line Build-Out: 0, -7.5, -15, -22.5 dB

(long), 0 to 655 ft (short)

•

UL/CUL 60950

•

DS0 Assignment: Programmable

Connector: RJ-48C

Environmental

•

Operating Temperature: 0°C to 50°C

Clock Source

Storage Temperature: -20°C to 70°C

Relative Humidity: Up to 95 percent,

noncondensing

•

Network

Internal

Through

Physical

•

Dimensions: 2.75-inch W x 4.25-inch D

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

NetVanta 1000/1000R Series Hardware Installation Guide

Option Modules

NetVanta E1/FE1 NIM (P/N 1200868E1/L1)

The NetVanta E1/FE1 module (see Figure 28) provides a WAN-E1 interface for the NetVanta meeting the

requirements of ITU-T G.703/G.704. The module provides a single 2.048 Mbps network interface. See

T a ble A-7 on page 69 for the pinouts. See page 73 for the DBU connector pinouts. An optional DIM is required

for dial backup applications.

WAN-E1

DBU

Figure 28. NetVanta E1/FE1 NIM

Features and Specifications

Operating Modes

Diagnostics

•

Frame Relay, Multilink Frame Relay

PPP, Multilink PPP

HDLC

•

Test Pattern Generation and Detection:

QRSS, 511, all ones, all zeros

Network loopbacks

Network performance data (15 minutes and

24 hours)

Alarm generation and detection

•

WAN-E1 Interface

•

Supported Standards: ITU G.703,

ITU-T G.704 (CRC-4), ITU-T G.823,

ITU-T G.797

•

Compliance

•

Line Rate: 2.048 Mbps +50 PPM

Line Code: AMI or HDB3

Framing: FAS with optional CRC-4

FE1 Line Rate: Channelized timeslot (in

multiples of 64 kbps)

•

AS/ACIF S016

ETSI TBR 12/TBR 13

EN 60950

IEC 60950

AS/NZS 60950

RoHS Compliant (Telecommunications

exemption)

•

Receiver Sensitivity: -30 dB

Connector: RJ-48C

Clock Source

•

Network

Internal

Environmental

•

Operating Temperature: 0°C to 50°C

Storage Temperature: -20°C to 70°C

Relative Humidity: Up to 95 percent,

noncondensing

Physical

•

Dimensions: 2.75-inch W x 4.25-inch D

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

Option Modules

NetVanta 1000/1000R Series Hardware Installation Guide

NetVanta E1/FE1 + G.703 Drop NIM (P/N 1200878E1/L1)

The NetVanta E1/FE1 + G.703 Drop NIM (see Figure 29) provides a single WAN-E1 interface (2.043 Mbps)

with user-selectable TS0 assignment, and a G.703 drop port that may be used to drop and insert traffic to an E1

PBX. See T a ble A-7 on page 69 for the WAN-E1 pinouts. See T a ble A-9 on page 70 for the G.703 pinouts. See

page 73 for the DBU connector pinouts. An optional DIM is required for dial backup applications.

WAN-E1

G.703

DBU

Figure 29. NetVanta E1/FE1 + G.703 Drop NIM

Features and Specifications

Diagnostics

Operating Modes

•

Frame Relay, Multilink Frame Relay

PPP, Multilink PPP

HDLC

•

Test Pattern Generation and Detection:

QRSS, 511, all ones, all zeros

Network loopbacks

Network performance data (15 minutes

and 24 hours)

Alarm generation and detection

•

WAN-E1 Interface

•

Supported Standards: ITU G.703,

ITU-T G.704 (CRC-4), ITU-T G.823,

ITU-T G.797

•

Compliance

•

Line Rate: 2.048 Mbps +50 PPM

Line Code: AMI or HDB3

Framing: FAS with optional CRC-4

FE1 Line Rate: Channelized timeslot (in

multiples of 64 kbps)

•

EMC - see Electromagnetic

AS/ACIF S016

ETSI TBR 12/TBR 13

EN 60950

IEC 60950

AS/NZS 60950

RoHS Compliant (Telecommunications

exemption)

•

Receiver Sensitivity: -30 dB

Connector: RJ-48C

G.703 Interface

•

Receiver Sensitivity: -30 dB

Line Rate: 2.048 Mbps +50 PPM

Line Code: AMI or HDB3

Framing: FAS with optional CRC-4

Capacity: 1 to 31 timeslots

Connector: RJ-48C

Environmental

•

Operating Temperature: 0°C to 50°C

Storage Temperature: -20°C to 70°C

Relative Humidity: Up to 95 percent,

noncondensing

Clock Source

Physical

•

Network

Internal

Through

•

Dimensions: 2.75-inch W x 4.25-inch D

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

NetVanta 1000/1000R Series Hardware Installation Guide

Option Modules

NetVanta Serial NIM (P/N 1200866E1)

The NetVanta Serial NIM (shown in Figure 30) can be configured by the user as a V.35, X.21 (V.11), or EIA 530

interface. This module supports rates up to a maximum of 10 Mbps. An additional V.35 (ADTRAN

P/N 1200873L1), X.21 (ADTRAN P/N 1200874L1), or EIA 530 (ADTRAN P/N 1200883L1) cable is required

(refer to Caution, below). See T a ble A-12 on page 71 for the serial connector pinouts, and page 73 for the DBU

connector pinouts. An optional DIM is required for dial backup applications.

Cable length for the Serial NIM should not exceed 25 feet.

SERIAL

DBU

Figure 30. NetVanta Serial NIM

Features and Specifications

Operating Mode

Environmental

•

DTE only

•

Operating Temperature: 0°C to 50°C

Storage Temperature: -20°C to 70°C

Relative Humidity: Up to 95 percent,

noncondensing

Serial Interface

•

Supported Standards: ISO 4903 (X.21),

CCITT V.35 Synchronous (V.35),

EIA 530 Synchronous

Physical

•

Provides V.35, X.21 (V.11), or EIA 530

electrical interface

Connector: 26-pin smart serial (DTE)

•

Dimensions: 2.75-inch W x 4.25-inch D

Compliance

•

EMC - see Electromagnetic

ETSI TBR1

ETSI TBR2

EN 60950

IEC 60950

UL/CUL 60950

AS/NZS 60950

RoHS Compliant (Telecommunications

exemption)

•

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

Option Modules

NetVanta 1000/1000R Series Hardware Installation Guide

NetVanta SHDSL NIM, Annex A (P/N 1200936E1)

The NetVanta SHDSL NIM, Annex A (shown in Figure 31) provides a WAN SHDSL interface for the

NetVanta. See T a ble A-10 on page 70 for the SHDSL connector pinouts.

WAN-SHDSL

ANNEX A

Figure 31. NetVanta SHDSL NIM, Annex A

Features and Specifications

Operating Mode

Diagnostics

•

Line termination (CO)

Network termination (CPE)

•

Network loopbacks (local and remote)

Alarm generation and detection

Programmable alarm threshold setting for

loop attenuation and signal-to-noise ratio

SHDSL Interface

•

Supported Standards: ITU-T G.991.2

SHDSL, Annex A

Compliance

M-pair bonding of 2 pairs - ITU.T

G.991.2

•

EMC - see Electromagnetic

ACTA/FCC Part 68

UL/CUL 60950

RoHS compliant (Telecommunications

exemption)

•

Line Rate (2-wire mode): 192 to

2304 kbps in 64k increments

Line Rate (4-wire mode): 384 to

4608 kbps in 128k increments

Payload: ATM (AAL5)

Line Code: TC-PAM

•

Environmental

•

Operating Temperature: 0°C to 50°C

Connector: RJ-45

Storage Temperature: -20°C to 70°C

Relative Humidity: Up to 95 percent,

noncondensing

Clock Source

•

CPE Operating Mode: Network

CO Operating Mode: Internal

Physical

•

Dimensions: 2.75-inch W x 4.25-inch D

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

NetVanta 1000/1000R Series Hardware Installation Guide

Option Modules

NetVanta SHDSL NIM, Annex B (P/N 1200937E1)

The NetVanta SHDSL NIM, Annex B (shown in Figure 32) provides a WAN SHDSL interface for the

NetVanta. See T a ble A-10 on page 70 for the SHDSL connector pinouts.

WAN-SHDSL

ANNEX B

Figure 32. NetVanta SHDSL NIM, Annex B

Features and Specifications

Operating Mode

Diagnostics

•

Line termination (CO)

Network termination (CPE)

•

Network loopbacks (local and remote)

Alarm generation and detection

Programmable alarm threshold setting for

loop attenuation and signal-to-noise ratio

SHDSL Interface

•

Supported Standards: ITU-T G.991.2

SHDSL, Annex B

Compliance

M-pair bonding of 2 pairs - ITU.T

G.991.2

•

EMC - see Electromagnetic

AS/ACIF S043

EN 60950

AS/NZS 60950

•

Line Rate (2-wire mode): 192 to

2304 kbps in 64k increments

Line Rate (4-wire mode): 384 to

4608 kbps in 128k increments

Payload: ATM (AAL5)

Line Code: TC-PAM

•

RoHS compliant (Telecommunications

exemption)

•

Environmental

Connector: RJ-45

•

Operating Temperature: 0°C to 50°C

Storage Temperature: -20°C to 70°C

Relative Humidity: Up to 95 percent,

noncondensing

Clock Source

•

CPE Operating Mode: Network

CO Operating Mode: Internal

Physical

•

Dimensions: 2.75-inch W x 4.25-inch D

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

Option Modules

NetVanta 1000/1000R Series Hardware Installation Guide

NetVanta ADSL NIM, Annex A (P/N 1202869E1)

The NetVanta ADSL NIM, Annex A (see Figure 33) adds ADSL capability to the NetVanta. The module

provides a single ADSL, ADSL2, or ADSL2+ network interface to support rates up to 25 Mbps. See T a ble A-11

on page 71 for the pinouts. The ADSL NIM supports an optional DIM for dial backup applications. See page 73

for the DBU connector pinouts.

WAN-ADSL

DBU

Figure 33. NetVanta ADSL NIM, Annex A

Features and Specifications

ADSL Interface

Compliance

•

ADSL over POTS, Annex A

Supported Standards:

•

EMC - see Electromagnetic

ACTA/FCC Part 68

AS/ACIF S043

AS/ACIF S002

IC CS-03

EN 60950

IEC 60950

UL/CUL 60950

AS/NZS 60950

•

–

ITU G.992.1 (G.dmt)

ITU G.992.2 (G.lite)

ITU G.992.3 ADSL2 (G.dmt.bis)

ITU G.992.5 ADSL2+

ANSI T1.413 Issue 2

Reach Extended ADSL (READSL2)

•

Connector: RJ-11C (6-pin jack, inner

pair)

RoHS Compliant (Telecommunications

exemption)

ATM

•

Multiple Protocol over AAL5 (RFC2684)

Environmental

PPP over ATM (RFC2364)

PPP over Ethernet (RFC2516)

ATM Forum UNI 3.1/4.0 PVC

ATM Class of Service (UBR)

ATM F5 OAM

•

Operating Temperature: 0°C to 50°C

Storage Temperature: -20°C to 70°C

Relative Humidity: Up to 95 percent,

noncondensing

Physical

Up to 16 Virtual Circuits

•

Dimensions: 2.75-inch W x 4.25-inch D

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

NetVanta 1000/1000R Series Hardware Installation Guide

Option Modules

NetVanta ADSL NIM, Annex B (P/N 1202889E1)

The NetVanta ADSL NIM, Annex B (see Figure 34) adds ADSL capability to the NetVanta. See T a ble A-11 on

page 71 for the pinouts. The ADSL NIM supports an optional DIM for dial backup applications.See page 73 for

the DBU connector pinouts.

WAN-ADSL

DBU

Figure 34. NetVanta ADSL NIM, Annex B

Features and Specifications

ADSL Interface

Compliance

•

ADSL over ISDN, Annex B

Supported Standards: ITU G.992.1

(G.dmt)

Connector: RJ-11C (6-pin jack,

inner pair)

•

EMC - see Electromagnetic

Interface Modules on page 57.

AS/ACIF S043

EN 60950

IEC 60950

AS/NZS 60950

RoHS Compliant (Telecommunications

exemption)

•

ATM

•

Multiple Protocol over AAL5 (RFC2684)

PPP over ATM (RFC2364)

PPP over Ethernet (RFC2516)

ATM Forum UNI 3.1/4.0 PVC

ATM Class of Service (UBR)

ATM F5 OAM

Environmental

•

Operating Temperature: 0°C to 50°C

Storage Temperature: -20°C to 70°C

Relative Humidity: Up to 95 percent,

noncondensing

Up to 16 Virtual Circuits

Physical

•

Dimensions: 2.75-inch W x 4.25-inch D

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

Option Modules

NetVanta 1000/1000R Series Hardware Installation Guide

NetVanta 3G CDMA NIM (P/N 1700801G1)

The NetVanta 3G CDMA NIM (shown in Figure 35) provides a cellular interface for the NetVanta 1335

and NetVanta 1335 PoE. Refer to Installing the 3G CDMA NIM Antennas on page 62 for information about

the specifications and installation of the 3G CDMA NIM antennas. For specific connection and

configuration instructions, refer to the 3G CDMA NIM Quick Start Guide or the 3G NIM Configuration

Guide available on the AOS Documentation CD shipped with the base unit or on the Web at

www.adtran.com.

ANT1

ANT2

RSSI

WWAN

1xRTT

EVDO

3G NIM (CDMA)

Figure 35. NetVanta 3G CDMA NIM

Features and Specifications

Environmental

Wireless Technologies

•

1xRTT

1xEV-DO Rev 0

1xEV-DO Rev A

•

Operating Temperature: 0°C to 50°C

Storage Temperature: -20°C to 70°C

Relative Humidity: Up to 95 percent,

noncondensing

Frequency Bands

•

Band Class 0 (Cellular 800 MHz)

Band Class 1 (PCS 1.9 GHz)

Physical

•

Dimensions: 2.75-inch W x 4.25-inch D

Standard SMA antenna connectors

Compliance

•

FCC Part 15, Class A

FCC Parts 2, 22, 24

UL/CUL 60950-1

RSS 102

RSS 129/133

RSS 132/133

IC ES-003

Download from Www.Somanuals.com. All Manuals Search And Download.

61200500L1-34N

NetVanta 1000/1000R Series Hardware Installation Guide

Option Modules

Table 2. 3G CDMA NIM LED Descriptions

Indication

3G modem is not powered.

LED Label LED Color

Off

Green (solid)

3G modem is powered, associated, and authenticated, but not

transmitting or receiving.

WWAN

Green (slow flash)

3G modem is powered and searching, but not associated or

authenticated.

Green (intermittent 3G modem activity proportional to transmitting/receiving speed

flash)

(3 Hz minimum rate, 20 Hz maximum rate).

No service or no signal detected.

Low signal strength.

RSSI

(Received

Signal

Strength

Indication)

Off

Red (solid)

Amber (solid)

Green (solid)

Off

Medium signal strength.

High signal strength.

No 1xRTT service is available.

1xRTT service is available.

No 1xEV-DO service is available.

1xEV-DO service is available.

1xRTT

EVDO

Green (solid)

Off

Green (solid)

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

Option Modules

NetVanta 1000/1000R Series Hardware Installation Guide

Dial Backup Interface Modules

NetVanta Analog Modem DIM (P/N 1200864L1)

The Analog Modem DIM provides a modem with data rates up to 33.6 kbps for the NetVanta. This DIM is a

plug-on card that connects to the NIM. For installation instructions, refer to Installing Dial Backup and Network

Features and Specifications

Features

•

Supported Standards: ITU V.90

Async

Compliance

•

EMC - see Electromagnetic Compatibility (EMC) Table on page 6.

ACTA/FCC Part 68

IC CS-03

UL/CUL 60950

Environmental

•

Operating Temperature: 0°C to 50°C

Storage Temperature: -20°C to 70°C

Relative Humidity: Up to 95 percent, noncondensing

Physical

•

Dimensions: 2.5-inch W x 3.75-inch D

The Analog Modem DIM can be used in two different modes:

1. Backup interface for a primary connection.

2. CONSOLE port for remote dial-in access.

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

NetVanta 1000/1000R Series Hardware Installation Guide

Option Modules

NetVanta ISDN BRI DIM (P/N 1200865L1)

The NetVanta ISDN BRI DIM provides dial backup access to the public switched telephone network (PSTN)

via Basic Rate ISDN for the NetVanta. This DIM is a plug-on module that connects to the NIM. For installation

instructions, refer to Installing Dial Backup and Network Interface Modules on page 57.

Features and Specifications

Features

•

Clear channel and bonding mode 1 call protocols

Network support for 64 kbps (1 B-channel) or 128 kbps (2 B-channels)

D-channel switch compatibility with AT&T 5ESS, Northern Telecom DMS-100, and National

ISDN-1

•

V.54 network loopback support

Compliance

•

EMC - see Electromagnetic Compatibility (EMC) Table on page 6.

ACTA/FCC Part 68

IC CS-03

UL/CUL 60950

Environmental

•

Operating Temperature: 0°C to 50°C

Storage Temperature: -20°C to 70°C

Relative Humidity: Up to 95 percent, noncondensing

Physical

•

Dimensions: 2.5-inch W x 3.75-inch D

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

Option Modules

NetVanta 1000/1000R Series Hardware Installation Guide

NetVanta ISDN S/T DIM (P/N 1200875L1)

The NetVanta ISDN S/T DIM provides dial backup access to the PSTN via Basic Rate ISDN for the NetVanta.

This DIM is a plug-on module that connects to the NIM. For installation instructions, refer to Installing Dial

Backup and Network Interface Modules on page 57.

Features and Specifications

Features

•

Clear channel and bonding mode 1 call protocols

Network support for 64 kbps (1 B-channel) or 128 kbps (2 B-channels)

D-channel switch compatibility with AT&T 5ESS, Northern Telecom DMS-100, National ISDN-1,

and Euro-ISDN

•

V.54 network loopback support

Compliance

•

EMC - see Electromagnetic Compatibility (EMC) Table on page 6.

AS/ACIF S031

ETSI TBR 3

EN 60950

IEC 60950

AS/NZS 60950

Environmental

•

Operating Temperature: 0°C to 50°C

Storage Temperature: -20°C to 70°C

Relative Humidity: Up to 95 percent, noncondensing

Physical

•

Dimensions: 2.5-inch W x 3.75-inch D

61200500L1-34N

Download from Www.Somanuals.com. All Manuals Search And Download.

NetVanta 1000/1000R Series Hardware Installation Guide

Unit Installation

5. UNIT INSTALLATION

The instructions and guidelines provided in this section cover hardware installation topics, such as mounting

options, supplying power to the unit, and installing option cards. These instructions are presented as follows:

•