Quick start guide (Canada version)
CL83101/CL83201/
CL83301/CL83351/
CL83401/CL83451
DECT 6.0 cordless telephone/
answering system with
caller ID/call waiting
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone base and charger installation
Install the telephone base and charger as shown below.
Telephone base installation
Plug the large end of
the power adapter into
a power outlet not
controlled by a wall
switch.
Plug one end of the
telephone line cord
into a telephone jack
or a DSL filter.
If you have DSL high-speed
Internet service, a DSL filter
(not included) is required.
Telephone line cord
Route the power adapter
cord through this slot.
Route the telephone line
cord through this slot.
Raise the antenna.
Plug the other end of the
telephone line cord into the
telephone jack on the back
of the telephone base.
Plug the small end of the
telephone base power
adapter into the power
adapter jack on the back
of the telephone base.
Charger installation
Plug the power adapter into an electrical outlet
not controlled by a wall switch.
IMPORTANT INFORMATION
• Use only the power adapter(s) supplied with this product. To order a replacement
1 (866) 288-4268.
• The power adapters are intended to be correctly oriented in a vertical or floor
mount position. The prongs are not designed to hold the plug in place if it is
plugged into a ceiling, under-the-table or cabinet outlet.
ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery installation and charging
Once you have installed the battery, the screen indicates the battery status. For
best performance, keep the handset in the telephone base or charger when
not in use. The battery is fully charged after ꢀ0 hours of continuous charging.
NOTE: If you are on a phone call in low battery mode, you hear four short beeps
every minute.
Step 1
Step 2
Plug the battery
Align the cover flat
against the battery
compartment, then
slide it upwards until
it clicks into place.
connector securely
into the socket inside
the handset battery
compartment, matching
the color-coded label.
Insert the supplied
battery with the label
THIS SIDE UP facing up
as indicated.
CHARGE light
Step 3
Charge the handset by placing it face forward in
the telephone base or charger. The CHARGE light
on the top of the handset is on during charging.
After you install your telephone or power returns following a power outage,
the handset will prompt you to set the date and time. For instructions, see
Set date/time on page 8. To skip, press OFF/CANCEL.
IMPORTANT INFORMATION
• Use only the supplied rechargeable battery or replacement battery (model BTꢀ6634ꢁ).
1 (866) 288-4268.
• If you do not use the handset for a long time, disconnect and remove the battery
to prevent possible leakage.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick reference guide - handset
pDIR/VOLUME
Press pDIR to show directory
entries when the handset is
not in use.
CHARGE indicator
On when the handset is
charging in the telephone base
or charger.
Press to scroll up while
in menus.
While entering names or
numbers, press to move the
cursor to the right.
qCID/VOLUME
Press qCID to show caller ID
history when the handset is not
in use.
Press to scroll down while in
menus.
While entering names or
numbers, press to move the
cursor to the left.
Press to increase the listening
volume when on a call, or to
increase the message
playback volume.
Press to decrease the listening
volume when on a call, or to
decrease the message playback
volume.
MENU/SELECT
When the handset is not in
use, press to show the menu.
While in the menu, press to
select an item or save an
entry or setting.
MUTE/DELETE
During a call, press to mute the
microphone.
When the handset is ringing,
press to mute the ringer
temporarily.
While reviewing the caller ID
history, the directory or the
redial memory, press to delete
an individual entry.
OFF/CANCEL
During a call, press to hang
up.
While in a menu, press to
cancel an operation, back up
to the previous menu, or exit
the menu display, or
press and hold this button to
exit to idle mode.
When the handset is ringing,
press to mute the ringer
temporarily.
Press and hold while the
telephone is not in use to
erase the missed call indicator.
While predialing, press to
delete digits.
During message or announcement
playback, press to delete the
playing message or the recorded
announcement
.
PHONE/FLASH
Press to make or answer a call.
# (pound key)
Press repeatedly to display
other dialing options when
reviewing a caller ID log entry.
During a call, press to answer
an incoming call when you
receive a call waiting alert.
During message playback, press
to call back the caller if caller’s
number is available.
EQ
During an outside call,
intercom call, message or
announcement playback,
press to change the audio
quality to best suit your
hearing.
1
While reviewing a caller ID
log entry, press repeatedly to
add or remove ꢀ in front of
the telephone number before
dialing or saving it in the
directory.
REDIAL/PAUSE
Press repeatedly to view
the last ꢀ0 numbers dialed.
While entering numbers,
press and hold to insert a
dialing pause.
/SPEA�ER
Press to make or answer a
call using the speakerphone.
Press to switch between
the speakerphone and the
handset.
TONE
Press to switch to tone dialing
temporarily during a call if you
have pulse service.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick reference guide - handset
PUSH TO TAL�
Press to initiate a one-to-one or
one-to-group broadcast.
Press and hold to broadcast to a group of
system devices.
Main menu
Main menu
• Play messages
• Answering sys
• Directory
• Caller ID log
• Intercom
• Ringers
The > symbol highlights
a menu item.
• Set date/time
• Settings
• Website
>Play messages
Answering sys
p
q
Using menus:
• Press MENU/SELECT to show the menu.
• Press qCID or pDIR to scroll through menu items.
• Press MENU/SELECT to confirm or save changes to a highlighted menu item.
• Press OFF/CANCEL to cancel an operation, back up to the previous
menu, or exit the menu display.
ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick reference guide - telephone base
CANCEL
MENU/SELECT
While in a menu, press to cancel an operation, When the telephone base is not in use, press
back up to the previous menu or exit the menu to show the menu.
display.
While in the menu, press to confirm or save an
Press and hold to go back to idle mode.
entry or setting.
When the telephone base is ringing, press to
mute the ringer temporarily.
pDIR
Press to display the directory when the phone is
not in use.
qCID
Press to display the caller ID history when
the phone is not in use.
Press to scroll up while in menus and lists.
While entering names and numbers, press to
Press to scroll down while in menus and lists. move the cursor to the right.
While entering names and numbers, press to
move the cursor to the left.
FLASH
During a call, press to answer an incoming call
when you receive a call waiting alert.
IN USE indicator
On when the telephone is in use, or when the
answering system is answering an incoming call.
On when a handset is being registered.
Flashes when there is an incoming call or when
all handsets are being deregistered.
Flashes when another telephone is in use on the
same line.
/HANDSET LOCATOR
While the phone is idle, press to
page all handsets.
REDIAL/PAUSE
Press repeatedly to view the last
ꢀ0 numbers dialed.
While entering numbers,
press and hold to insert a dialing
pause.
q/VOLUME/p
PTT
MIC
During message playback or call
screening, press to adjust the listening
volume.
Press to initiate a one-to-one or
one-to-group broadcast.
Microphone
Press and hold to broadcast to a
group of system devices.
While in idle mode, press to adjust the
base ringer volume.
When on a call, press to adjust the
listening volume.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick reference guide - telephone base
X/DELETE
While reviewing the caller ID history, the directory or the redial
memory, press to delete an individual entry.
While predialing, press to delete digits.
During message or announcement playback, press to delete the
playing message or the recorded announcement.
Press twice to delete all old messages when the phone is not
use.
in
/ANSWER ON
Press to turn the built-in answering system on or off.
•/RECORD
Press to record a memo or an announcement.
/REPEAT
During playback, press to repeat the playing message.
During playback, press twice to play the previous message.
/S�IP
Press to skip a message.
/PLAY/STOP
Press to start or stop message playback.
MUTE
During a call, press to mute the microphone.
When the phone is ringing, press to mute the ringer temporarily.
/SPEA�ER
Press to make or answer a call using the speakerphone.
Main menu
Main menu
• Play messages
• Answering sys
• Directory
The > symbol highlights
a menu item.
• Caller ID log
• Intercom
• Ringers
• Set date/time
• Settings
>Playing messages
Answering sys
p
q
• Website
Using menus:
• Press MENU/SELECT to show the menu.
• Press qCID or pDIR to scroll through menu items.
• Press MENU/SELECT to confirm or save changes to a highlighted menu item.
• Press CANCEL to cancel an operation, back up to the previous menu, or
exit the menu display.
ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone settings
Set date/time
To set the date and time manually:
Ringers
ꢀ. When the handset or telephone base is in idle mode, press
>Set date/time
p
q
MENU/SELECT to enter the main menu.
ꢁ. Press qCID or pDIR to scroll to >Set date/time and then
press MENU/SELECT.
SET DATE
MM/DD/YY
3. Press qCID or pDIR to select the month, then press
MENU/SELECT, or enter the number using the dialing keys.
p
q
4. Press qCID or pDIR to select the day, then press
MENU/SELECT, or enter the number using the dialing keys.
ꢂ. Press qCID or pDIR to select the year, then press
MENU/SELECT, or enter the number using the dialing keys,
then press MENU/SELECT to move on to set the time.
SET TIME
HH:MM --
p
q
6. Press qCID or pDIR to select the hour, then press
MENU/SELECT, or enter the number using the dialing keys.
ꢃ. Press qCID or pDIR to select the minute, then
Ringers
>Set date/time
press MENU/SELECT, or enter the number using the
dialing keys.
p
q
8. Press qCID or pDIR to highlight AM or PM, or press
2 for AM or 7 for PM. Then press MENU/SELECT to
confirm. There is a confirmation tone and the screen
returns to the previous menu.
SET DATE
MM/DD/YY
p
q
SET TIME
HH:MM --
NOTE: If the clock is not set when a message is recorded, the
system announces, “Time and day not set,” before it plays the
message.
p
q
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone operation
Making a call
Using a cordless handset:
Elapsed time
• Press PHONE/FLASH or /SPEA�ER, then enter the
Phone 0:00:30
telephone number.
The screen displays the elapsed time as you talk (in hours,
minutes and seconds).
8/06
6:30AM
Using the telephone base:
Speaker 0:00:30
• Press /SPEA�ER, then enter the telephone number.
The screen displays the elapsed time as you talk (in hours,
minutes and seconds).
8/06
6:30AM
Elapsed time
Speaker 0:00:30
NOTE: Pressing PHONE/FLASH or
/SPEA�ER to access
services from your telephone service provider does not affect the
elapsed time.
8/06
6:30AM
Answering a call
Using a cordless handset:
• Press PHONE/FLASH or /SPEA�ER.
-OR-
• Press any dialing key (0-9, TONE or #).
Using the telephone base:
• Press /SPEA�ER.
-OR-
• Press any dialing key (0-9, TONE or #).
Ending a call
Using a cordless handset:
• Press OFF/CANCEL or return the handset to the telephone base or charger.
Using the telephone base:
• Press /SPEA�ER.
ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Answering system operation
Turn the answering system on or off
Using a cordless handset:
ꢀ. When the handset is in idle mode, press MENU/SELECT to
Play messages
>Answering sys
enter the main menu.
p
q
ꢁ. Press qCID or pDIR to scroll to >Answering sys, then
press MENU/SELECT.
3. Press qCID or pDIR to scroll to >Answer ON/OFF, then
press MENU/SELECT.
Record memo
>Answer ON/OFF
4. Press qCID or pDIR to highlight >On or >Off, then
press MENU/SELECT to save the setting. You hear a
confirmation tone.
p
q
When the answering system is on, the handset shows
ANS ON.
ANSWER ON/OFF
>On
p
q
Using the telephone base:
• Press /ANSWER ON to turn the answering system on
or off. If the answering system is turned on, it announces,
“Calls will be answered.” If the answering system is
turned off, it announces, “Calls will not be answered.”
Record a new outgoing announcement:
Using a cordless handset:
ꢀ. When the handset is in idle mode, press MENU/SELECT to enter the
main menu.
ꢁ. Press qCID or pDIR to scroll to >Answering sys, then press MENU/SELECT.
3. Press MENU/SELECT again to select >Announcement.
Play annc
4. Scroll to >Record annc and press MENU/SELECT. The
>Record annc
system announces, “Record after the tone. Press 5 when you
p
q
are done.”
ꢂ. Speak towards the handset to record your announcement.
Press 5 to end recording. Your recorded announcement plays.
To listen to the recorded announcement again, scroll to >Play annc and
press MENU/SELECT.
Using the telephone base:
ꢀ. When the telephone base is in idle mode, press
•/RECORD.
ꢁ. Press qCID or pDIR to scroll to >Announcement and
press MENU/SELECT. The system announces, “Record
after the tone. Press 5 when you are done.”
3. Speak towards the telephone base to record your
Record memo
>Announcement
announcement. Press 5 to end recording. Your recorded
p
q
announcement plays.
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Answering system operation
Listen to messages at the telephone base:
Press
/PLAY/STOP on the telephone base to
listen to the messages. The system announces the
number of messages, then begins playback.
Options during playback:
• Press q/VOLUME/pto adjust the message
playback volume.
• Press /S�IP to skip to the next message.
• Press /REPEAT to repeat the message. Press twice to hear the
previous message.
• Press X/DELETE to delete the message.
• Press
/PLAY/STOP to stop the playback.
• Press /SPEA�ER to call back the caller if caller’s number is available.
ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Answering system operation
Listen to messages on a cordless handset:
ꢀ. When the handset is in idle mode, press MENU/SELECT to
>Play messages
Answering sys
enter the main menu.
p
q
ꢁ. Press MENU/SELECT again to select >Play messages.
• If there are new and old messages, press qCID or pDIR
to select >Play new msgs or >Play old msgs, then press
MENU/SELECT.
>Play new msgs
Play old msgs
• If there are only new messages, they will play
automatically.
Options during playback:
3 New messages
• Press PHONE/FLASH to stop playback. The screen shows
Call back?, then press MENU/SELECT, PHONE/FLASH, or
/SPEA�ER to call back the caller.
ANS ON
10:01AM
10/15
• Press MENU/SELECT to pause playback and show the
caller ID information if available. From here, you can press
OFF/CANCEL to resume playback or press
PHONE/FLASH to call back the caller. If you do not
call back within ꢀ0 seconds, message playback resumes
automatically.
Charlie Johnson
4-Repeat 6-Skip
ANS ON
MSG#
1/3
10:01AM
• Press qCID/VOLUME or pDIR/VOLUME to adjust the message
playback volume.
• Press EQ
to adjust the message playback audio quality.
• Press 6 to skip to the next message.
• Press 4 to repeat the message. Press twice to hear the previous message.
• Press MUTE/DELETE to delete the message.
• Press 5 or OFF/CANCEL to stop the playback.
• Press /SPEA�ER to switch between speakerphone mode and
handset mode.
NOTE: The equalizer stays on the same settings until you change it by pressing EQ .
ꢀꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
© ꢁ0ꢀꢀ Advanced American Telephones. All Rights Reserved.
AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to
Advanced American Telephones, San Antonio, TX ꢃ8ꢁꢀꢄ.
Printed in China. Issue ꢀ AT&T 0ꢁ/ꢀꢀ.
Download from Www.Somanuals.com. All Manuals Search And Download.
|