3M Oxygen Equipment 8310 User Manual

3M Occupational Health & Environmental Safety Group  
3M8300 Series Comfort Respirators  
Fitting Instructions  
Fit Check Procedure  
3M 8300 Series Comfort Respirators  
For Valved Respirators:  
Respirator  
8310  
Type  
APF  
4
VALVE  
a) Cover the front of the respirator with both  
hands, being careful not to disturb the  
position of the respirator.  
FFP1 NR D  
FFP1 NR D  
FFP2 NR D  
FFP2 NR D  
FFP3 R D  
4
8312  
1
2
3
4
5
10  
10  
20  
8320  
b) Inhale sharply. A negative pressure should be felt inside the respirator. If air leaks around  
the nose, readjust the noseclip as described in step 4 to eliminate leakage. Repeat the  
above fit check. If air leaks at the respirator edges, work the straps back along the sides  
of the head to eliminate leakage. Retest the seal. Repeat the procedure until the respirator  
fits properly.  
8322  
1. Cup the respirator in your hand with the nosepiece at your fingertips allowing the  
headbands to hang freely below your hand.  
8833  
Standard: EN149:2001 + A1:2009  
2. Position the respirator under your chin with the nosepiece up.  
This respirator should not be used in oxygen deficient environments, for  
escape purposes or by people with beards/ facial hair or in atmospheres  
where concentrations of contaminant may exceed that deemed  
Immediately Dangerous to Life and Health (IDLH).  
3. Pull the top strap over your head resting it high at the top back of your head. Pull the  
bottom strap over your head and position it around the neck below the ears. Make  
sure that the straps are not twisted.  
For Unvalved Respirators:  
a) Cover the front of the respirator with both  
hands, being careful not to disturb the  
position of the respirator.  
4. Place the fingertips of both hands at the top of the metal nosepiece.  
Mould the nosepiece to the shape of your nose by pushing inward while moving your  
fingertips down both sides of the nosepiece.  
4
5
b) Exhale sharply.A positive pressure should  
Pinching the nosepiece using one hand may result in less effective respirator  
performance.  
be felt inside the respirator. If air leaks around the nose, readjust the noseclip as described  
in step 4 to eliminate leakage. Repeat the above fit check. If air leaks at the respirator  
edges, work the straps back along the sides of the head to eliminate leakage. Retest the  
seal. Repeat the procedure until the respirator fits properly.  
5. The seal of the respirator on the face should be fit checked prior to wearing in the  
work area.  
If you cannot achieve a proper fit, do not enter the contaminated area.  
See your supervisor.  
Note: Do not use with beards or other facial hair that may inhibit contact between the  
face and the edge of the respirator.  
Occupational Health & Environmental Safety Group  
3M United Kingdom plc  
3M Centre,  
Cain Road, Bracknell  
Berkshire RG12 8HT  
Tel: 0870 60 800 60  
3M Ireland Limited  
The Iveagh Building  
The Park  
Carrickmines  
Dublin 18  
Fit Testing: The 3M 8300 Series Respirator is a tight fitting facepiece and therefore  
wearers require a fit test as per the COSHH regulations 2002. For qualitative testing -  
3MFT10 and FT30 Fit Test Kits are available.  
Please recycle. Printed in UK.  
© 3M 2009. All rights reserved.  
CH8300FP V2  
Tel: 1 800 320 500  
Download from Www.Somanuals.com. All Manuals Search And Download.  

3Com Switch TR User Manual
AEG Microwave Oven MC_170 User Manual
Agri Fab Lawn Aerator 45 0381 User Manual
Aiwa CD Player XR MR5 User Manual
Alcatel Lucent Network Router 5750 SSC User Manual
Amana Clothes Dryer W10216186A User Manual
American Standard Bathroom Aids 701019 User Manual
ATON Speaker A60W User Manual
Audiovox Remote Starter APS 700 User Manual
Barco Computer Monitor MD 4221 User Manual