3M Marine RADAR 700a s User Manual

Instructions and Parts List  
Important Safety  
Information  
3M-Matic  
BEFORE INSTALLING OR  
OPERATING THIS  
EQUIPMENT  
700a-s  
Type 10500  
Read, understand, and follow  
all safety and operating  
instructions.  
Adjustable  
Case Sealer  
with  
AccuGlide SST  
Spare Parts  
Taping Heads  
It is recommended you  
immediately order the spare  
parts listed in the "Spare  
Parts/Service Information"  
section. These parts are  
expected to wear through  
normal use, and should be  
kept on hand to minimize  
production delays.  
Serial No.  
For reference, record machine serial number here.  
3M-Maticand AccuGlideare Trademarks  
of 3M, St. Paul, MN 55144-1000  
3M Industrial Adhesives and Tapes  
3M Center, Building 220-5E-06  
St. Paul, MN 55144-1000  
Printed in U.S.A.  
© 3M 2005 44-0009-2038-7 (A)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacement Parts and Service Information  
To Our Customers:  
This is the 3M-Matic™/AccuGlide™/Scotch® equipment you ordered. It  
has been set up and tested in the factory with Scotch® tapes. If technical  
assistance or replacement parts are needed, call or fax the appropriate  
number listed below.  
Included with each machine is an Instructions and Parts List manual.  
Technical Assistance:  
3M-Matic™ Helpline – 1-800/328 1390. Please provide the customer support  
coordinator with the machine number, machine type/model and serial number.  
If you have a technical question that does not require an immediate response,  
you may Fax it to 651-736-7282.  
Replacement Parts and Additional Manuals  
Order parts by part number, part description and quantity required. Also,  
when ordering parts and/or additional manuals, include machine name,  
number and type. A parts order form is provided at the back of this manual.  
3M/Tape Dispenser Parts  
241 Venture Drive  
1-800/344 9883  
Amery, WI 54001-1325  
FAX# 715/268 8153  
Minimum billing on parts orders will be $25.00. Replacement part prices available on request.  
$10.00 restocking charge per invoice on returned parts.  
Note : Outside the U.S., contact the local 3M subsidiary for parts ordering information.  
3M-Matic, AccuGlideand Scotchare Trademarks of  
3M, St. Paul, MN 55144-1000  
3M Industrial Adhesives and Tapes  
Printed in U.S.A.  
3M Center, Building 220-5E-06  
St. Paul, MN 55144-1000  
© 3M 2005 44-0009-1851-4 (F)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacement Parts And Service Information  
To Our Customers:  
This is the 3M-Matic™/AccuGlide™/Scotch® equipment you ordered. It  
has been set up and tested in the factory with Scotch® tapes. If any  
problems occur when operating this equipment and you desire a service  
call or phone consultation, call, write or fax the appropriate number listed  
below.  
Included with each machine is an Instructions and Parts List manual.  
SERVICE, REPLACEMENT PARTS AND ADDITIONAL MANUALS  
AVAILABLE DIRECT FROM:  
Order parts by part number, part description and quantity required. Also, when  
ordering parts and/or additional manuals, include machine name, number and  
type.  
3M-Matic, AccuGlideand Scotchare Trademarks of  
3M, St. Paul, MN 55144-1000  
3M Industrial Adhesives and Tapes  
Printed in U.S.A.  
3M Center, Building 220-5E-06  
St. Paul, MN 55144-1000  
© 3M 2005 44-0009-1852-2(E)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Instruction Manual  
700a-s Stainless Steel, Adjustable Case Sealer, Type 10500  
This instruction manual is divided into two sections as follows:  
Section I  
Section II  
Includes all information related to installation, operation and parts for the case sealer.  
Includes specific information regarding the AccuGlide™ SST 2 Inch Taping Heads.  
Table of Contents  
Page  
Section I – 700a-s Stainless Steel Adjustable Case Sealer  
Intended Use ...................................................................................................................................  
Equipment Warranty and Limited Remedy ......................................................................................  
700a-s Contents ..............................................................................................................................  
Important Safeguards ......................................................................................................................  
Specifications ..................................................................................................................................  
1
2
2
3 - 6  
7 - 9  
Installation and Set-Up ....................................................................................................................  
Receiving and Handling ......................................................................................  
Machine Set-Up ..................................................................................................  
Packaging and Separate Parts .................................................................  
Machine Bed Height ..................................................................................  
Outboard Tape Roll Mounting ...................................................................  
Tape Leg Length .......................................................................................  
Box Size Capacity of Case Sealer.............................................................  
Electrical Connection and Controls ...........................................................  
Initial Start-Up of Case Sealer ...................................................................  
10 - 13  
10  
10 - 13  
10 -11  
12  
12  
12  
13  
13  
13  
Operation.........................................................................................................................................  
Electrical On/Off Switch ......................................................................................  
Emergency Stop Switch......................................................................................  
Tape Loading/Threading.....................................................................................  
Box Size Set-Up .................................................................................................  
Adjust Upper Taping Head ........................................................................  
Adjust Side Guides ...................................................................................  
Run Boxes To Check Adjustment .............................................................  
Top Flap Compression Rollers..................................................................  
Adjust Compression Rollers......................................................................  
Box Sealing ........................................................................................................  
14 - 18  
15  
15  
15  
16 - 18  
16  
16  
17  
17  
18  
18  
(Table of Contents continued on next page)  
i
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents (Continued)  
Page  
Maintenance ....................................................................................................................................  
Cleaning .............................................................................................................  
Lubrication ..........................................................................................................  
Box Drive Belt Replacement ...............................................................................  
Circuit Breaker....................................................................................................  
Blade Replacement, Taping Head ......................................................................  
19 - 21  
19  
19  
20  
21  
21  
Adjustments ...................................................................................................................................  
Box Drive Belt Tension .......................................................................................  
Taping Head Adjustments ..................................................................................  
22 - 24  
22 - 23  
24  
Troubleshooting...............................................................................................................................  
Electrical Diagram ...........................................................................................................................  
Parts and Service Information .........................................................................................................  
Options/Accessories........................................................................................................................  
Replacement Parts Illustrations and Parts Lists...................................................... (Yellow Section)  
28  
29  
30  
31  
32 - 55  
Section II – AccuGlide™ SST 2 Inch Taping Heads  
(See Section II for Table of Contents)  
ii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Intended Use  
The 3M-MaticTM 700a-s Stainless Steel Adjustable Case Sealer with AccuGlideTM SST Taping Heads is designed  
to apply a “C” clip of Scotch® pressure-sensitive film box sealing tape to the top and bottom center seam of regular  
slotted containers. The 700a-s is manually adjustable to a wide range of box sizes (see "Specifications Section –  
Box Weight and Size Capacities").  
3M-MaticTM 700a-s Stainless Steel Adjustable Case Sealer, Type 10500  
Note – Lower tape supply roll and bracket assembly are shown in the alternate location.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Equipment Warranty and Limited Remedy: THE FOLLOWING WARRANTY IS MADE IN LIEU OF ALL  
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTY OF MERCHANTABILITY, THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR  
PURPOSE AND ANY IMPLIED WARRANTY ARISING OUT OF A COURSE OF DEALING, A CUSTOM OR  
USAGE OF TRADE:  
3M sells its 3M-Matic 700a-s Adjustable Case Sealer, Type 10500 with the following warranties:  
1.  
The drive belts and the taping head knives, springs and rollers will be free from all defects for ninety (90)  
days after delivery.  
2.  
3.  
All other taping head parts will be free from all defects for three (3) years after delivery.  
All other parts will be free from all defects for two (2) years after delivery.  
If any part is proved to be defective within its warranty period, then the exclusive remedy and 3M’s and seller’s  
sole obligation shall be, at 3M’s option, to repair or replace the part, provided the defective part is returned  
immediately to 3M’s factory or an authorized service station designated by 3M. A part will be presumed to have  
become defective after its warranty period unless the part is received or 3M is notified of the problem no later than  
five (5) calendar days after the warranty period. If 3M is unable to repair or replace the part within a reasonable  
time, then 3M at its option, will replace the equipment or refund the purchase price. 3M shall have no obligation  
to provide or pay for the labor required to install the repaired or replacement part. 3M shall have no obligation to  
repair or replace (1) those parts failing due to operator misuse, carelessness, or due to any accidental cause  
other than equipment failure, or (2) parts failing due to non-lubrication, inadequate cleaning, improper operating  
environment, improper utilities or operator error.  
Limitation of Liability: 3M and seller shall not be liable for direct, indirect, special, incidental or consequential  
damages based upon breach of warranty, breach of contract, negligence, strict liability or any other legal theory.  
The foregoing Equipment Warranty and Limited Remedy and Limitation of Liability may be changed only by a  
written agreement signed by authorized officers of 3M and seller.  
Contents – 700a-s Stainless Steel Adjustable Case Sealer  
(1)  
(1)  
(1)  
(2)  
(1)  
(1)  
700a-s Stainless Steel Adjustable Case Sealer, Type 10500  
Upper Assembly Height Adjustment Crank/Hardware  
UpperTapeDrum/Bracket/Hardware  
ColumnStopBracket/Hardware  
Tool/Spare Parts Kit  
Instruction and Parts Manual  
Scotch®, AccuGlideTM, and 3M-MaticTM are Trademarks of 3M, St. Paul, Minnesota 55144-1000  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safeguards  
This safety alert symbol identifies  
important messages in this manual.  
READANDUNDERSTANDTHEMBEFORE  
INSTALLING OR OPERATING THIS  
EQUIPMENT.  
WARNING  
(continued)  
To reduce the risk associated with sharp  
blade hazards:  
Keep hands and fingers away from tape cutoff  
blades under orange blade guards. The  
blades are extremely sharp  
Explanation of Signal Word Consequences  
To reduce the risk associated with fire and  
explosion hazards:  
Indicates a potentially hazardous  
situation, which, if not avoided,  
could result in death or serious  
injury and/or property damage.  
WARNING:  
Do not operate this equipment in potentially  
flammable/explosiveenvironments  
To reduce the risk associated with muscle  
Indicates a potentially hazardous  
situation, which, if not avoided,  
may result in minor or moderate  
injury and/or property damage.  
CAUTION:  
strain:  
Use the appropriate rigging and material  
handling equipment when lifting or  
repositioning this equipment  
Use proper body mechanics when removing  
or installing taping heads that are moderately  
heavy or may be considered awkward to lift  
WARNING  
To reduce the risk associated with  
mechanical and electrical hazards:  
CAUTION  
Read, understand and follow all safety and  
operating instructions before operating or  
servicing the case sealer  
To reduce the risk associated with pinch  
and entanglement hazards:  
Allow only properly trained and qualified  
personnel to operate and/or service this  
equipment  
Keep hands clear of the upper head support  
assembly as boxes are transported through  
the machine  
Turn electrical supply off and disconnect  
beforeperforminganyadjustments,  
maintenance or servicing the machine or  
tapingheads  
Keep hands, hair, loose clothing and jewelry  
away from box compression rollers  
Always feed boxes into the machine by  
pushing only from the end of the box  
To reduce the risk associated with pinch  
and entanglement hazards:  
Keep hands, hair, loose clothing, and jewelry  
away from moving belts and taping heads  
Do not leave the machine running while  
unattended  
Turn the machine off while not in use  
Never attempt to work on any part of the  
machine, load tape, or remove jammed boxes  
from the machine while the machine is  
running  
To reduce the risk associated with  
hazardous voltage:  
Position electrical cord away from foot and/or  
vehicletraffic  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safeguards (Continued)  
Important – In the event the following safety labels are damaged or destroyed, they must be replaced to ensure  
operator safety. Replacement part numbers for individual labels are shown in Figures 1-1 and 1-2, or a label kit,  
part number 78-8098-9175-3, is available that includes all labels used on the machine.  
Figure 1-1 – Replacement Labels/3M Part Numbers  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safeguards (Continued)  
78-8060-8481-6(4)  
Leg Height Adjustment Label  
(Notshown)  
78-8070-1339-2(2)  
3M Logo (Each side of upper  
assembly - Not shown)  
Figure 1-2 – Replacement Labels/3M Part Numbers  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safeguards (Continued)  
Skill 2 - Mechanical Maintenance Technician  
This operator is trained to use the machine as the  
MACHINE OPERATOR and in addition is able to work  
with the safety protection disconnected, to check and  
adjust mechanical parts, to carry out maintenance  
operations and repair the machine. He is not allowed  
to work on live electrical components.  
WARNING  
To reduce the risk associated with  
mechanical and electrical hazards:  
Allow only properly trained and qualified  
personnel to operate and/or service this  
equipment  
Skill 2a - Electrical Maintenance Technician  
This operator is trained to use the machine as the  
MACHINE OPERATOR and in addition is able to work  
with the safety protection disconnected, to make  
adjustments, to carry out maintenance operations and  
repair the electrical components of the machine. He is  
allowed to work on live electrical panels, connector  
blocks, control equipment, etc.  
Operator Skill Level Descriptions  
Skill 1 - Machine Operator  
This operator is trained to use the machine with the  
machine controls, to feed cases into the machine,  
make adjustments for different case sizes, to change  
the tape and to start, stop and restart production.  
N.B.: the factory manager must ensure that the  
operator has been properly trained on all the machine  
functions before starting work.  
Skill 3 - Specialist From the Manufacturer  
Skilled operator sent by the manufacturer or its agent  
to perform complex repairs or modifications, when  
agreed with the customer.  
Operator's Skill Levels Required to Perform the Main Operations on Machine  
Operator's  
Skill  
Number of  
Operators  
Operation  
Installation and set up of the machine.  
Adjustment of the box size.  
Tape replacement.  
State of the Machine  
Running with safety protections  
disabled.  
2 and 2a  
2
1
1
Stopped by pressing the  
EMERGENCY STOP button.  
1
1
Stopped by pressing the  
EMERGENCY STOP button.  
Replacement of blades.  
Replacement of drive belts.  
Ordinary maintenance.  
Electric power disconnected.  
Electric power disconnected.  
Electric power disconnected.  
2
2
2
1
1
1
Extraordinary maintenance  
(mechanical).  
Running with safety protections  
disabled.  
3
1
1
Running with safety protections  
disabled.  
Extraordinary maintenance (electrical).  
2a  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
1. Power Requirements:  
Electrical - 115 VAC, 60 Hz, 5.6 A  
The machine is equipped with a 2.4 m [8 foot] standard neoprene covered power cord and a grounded plug.  
Contact your 3M Representative for power requirements not listed above.  
2. Operating Rate:  
Box drive belt speed is approximately 0.4 m/s [78 feet per minute].  
3. Operating Conditions:  
IMPORTANT SAFEGUARD  
Use in a relatively clean environment at 5o to 40o C [40o to 105o F] with clean, dry boxes.  
Important: Machine should not be washed down.  
WARNING  
IMPORTANTSAFEGUARD  
To reduce the risk associated with fire and  
explosion hazards:  
Do not operate this equipment in potentially  
flammable/explosiveenvironments  
4. Tape:  
Scotch® pressure-sensitive film box sealing tapes.  
5. Tape Width:  
36 mm [1 1/2 inch] minimum to 48 mm [2 inch] maximum  
(Specifications continued on next page.)  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications (Continued)  
6. Tape Roll Diameter:  
Up to 405 mm [16 inch] maximum on a 76.2 mm [3 inch] diameter core.  
(Accommodates all system roll lengths of Scotch® film tapes.)  
7. Tape Application Leg Length – Standard:  
70 mm ± 6 mm [2.75 inch ±.25 inch ]  
8. Box Board:  
Style – regular slotted containers – RSC  
125 to 275 P.S.I. bursting test, single wall or double wall B or C flute.  
9. Box Weight and Size Capacities:  
A. Box Weight, filled – up to 38.6 kg [85 lbs.] maximum. Contents must support flaps.  
B. Box Size:  
Length –  
Minimum  
Maximum  
150 mm [6.0 inch]  
150 mm [6.0 inch]*  
120 mm [4.75 inch]**  
Unlimited  
550 mm [21.5 inch]  
620 mm [24.5 inch] **  
Width  
Height –  
* Cartons narrower than 250 mm [10 inch] in width may require more frequent belt replacement  
because of limited contact area.  
** 165 mm [6.5 inch] minimum to 725 mm [28.5 inch] maximum height with columns adjusted to upper  
position. (See "Special Set-Up Procedure – Box and Machine Bed Height Range".)  
Special modifications may be available for carton sizes not listed above.  
Contact your 3M Representative for information.  
Note: The case sealer can accommodate most boxes within the size range listed above. However, if the  
box length (in direction of seal) to box height ratio is .5 or less, then several boxes should be test run to  
assure proper machine performance.  
DETERMINE THE BOX LIMITATIONS BY COMPLETING THIS FORMULA:  
=
BOX LENGTH IN DIRECTION OF SEAL  
BOXHEIGHT  
MUST BE GREATER THAN .5  
Any box ratio approaching this limitation should be test run to assure performance.  
(Specifications continued on next page.)  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications (Continued)  
10. Machine Dimensions:  
W
L
H
A*  
B
C**  
F
Minimum  
mm  
[Inches]  
790  
[31]  
1030  
[40 .5]  
1350  
[53]  
460  
[18]  
610  
[24]***  
100  
[4]  
625  
[24.5]  
Maximum  
mm  
[Inches]  
2185  
[86]***  
890  
[35]***  
- -  
- -  
- -  
- -  
- -  
* Infeed/Exitconveyorsareoptional  
** Casters are optional  
*** When columns are adjusted to upper position, "B" minimum dimension is 520 mm [20.5 inch], maximum  
dimension is 780 mm [31 inch] and "H" maximum dimension is 2290 mm [90 inch]. (See "Special Set-Up  
Procedure – Box and Machine Bed Height Range".)  
Weight – 180 kg [400 lbs] crated (approximate)  
160 kg [350 lbs] uncrated (approximate)  
11. Set-Up Recommendations:  
• Machine must be level.  
• Customer supplied infeed and exit conveyors (if used) should provide straight and level box entry and exit.  
• Exit conveyors (powered or gravity) must convey sealed boxes away from machine.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation and Set-Up  
Receiving And Handling  
After the machine has been uncrated, examine the  
case sealer for damage that might have occurred  
during transit. If damage is evident, file a damage  
claim immediately with the transportation company  
and also notify your 3M Representative.  
6. Loosen and move both compression rollers out  
so they don't catch on side guides.  
7. Install height adjustment crank and locking knob  
on top of left column as shown in  
Figure 2-1B. Crank upper assembly up high  
enough to allow clear access to lower taping  
head. Remove and discard the two cushion  
shipping blocks.  
Machine Set-Up  
WARNING  
8. Using 17 mm wrench, remove nuts from top of  
side guides. Replace with black knobs from  
parts box. Figure 2-1C.  
To reduce the risk associated with  
mechanical and electrical hazards:  
9. Cut and remove cable ties on both upper and  
lower taping heads. (Applying/buffing rollers are  
held retracted for shipment.)  
Read, understand and follow all safety and  
operating instructions before operating or  
servicing the case sealer  
The following instructions are presented in the order  
recommended for setting up and installing the case  
sealer, as well as for learning the operating  
functions and adjustments. Following them step by  
step will result in your thorough understanding of the  
machine and an installation in your production line  
that best utilizes the many features built into the case  
sealer. Refer to Figure 3-1 to identify the various  
components of the case sealer.  
WARNING  
To reduce the risk associated with sharp  
blade hazards:  
Keep hands and fingers away from tape cutoff  
blades under orange blade guards. The  
blades are extremely sharp  
Hold taping head BUFFING ROLLER and cut  
and remove cable tie that holds applying/  
buffing arms retracted. See Figure 2-1D.  
Allow buffing/applying arms to extend slowly.  
Note – A tool kit consisting of metric open end  
and hex socket wrenches is provided with the  
machine. These tools should be adequate to set-  
up the machine, however, other tools supplied by  
the customer will be required for machine  
maintenance.  
10. Install machine stops onto columns as shown in  
Figure 2-1E. Use the lowest hole position and  
bolt into the lowest threaded insert on the  
column.  
PACKAGING AND SEPARATE PARTS  
1. Remove straps and staples and lift fiberboard  
coveroffpallet.  
2. Removeprotectivewrappingaroundmachine.  
3. Cut and remove cable tie from electrical conduit.  
4. Cut cable ties that secure upper assembly to  
machine bed on each side.  
5. Remove tape drum bracket bolts (4) from top  
crossbar and install tape drum bracket from  
parts box as shown in Figure 2-1A.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation and Set-Up (Continued)  
Figure 2-1 – 700a-s Frame Set-Up  
WARNING  
11. Check for free action of both upper and lower  
taping heads.  
To reduce the risk associated with muscle  
strain:  
WARNING  
Use the appropriate rigging and material  
handling equipment when lifting or  
repositioning this equipment  
To reduce the risk associated with sharp  
blade hazards:  
Use proper body mechanics when removing  
or installing taping heads that are moderately  
heavy or may be considered awkward to lift  
Keep hands and fingers away from tape cutoff  
blades under orange blade guards. The  
blades are extremely sharp  
14. Remove the machine from the pallet and move it  
into position.  
Push buffing roller into head to check for free,  
smooth action of taping heads.  
Important – Whenever the machine is lifted with  
a fork truck, insure that the forks span com-  
pletely across the machine frame and do not  
contact any wiring or mechanism under the  
machine frame. In some cases the lower taping  
head may need to be removed to avoid damage.  
12. Ensure that the tape drum bracket assembly,  
located on the lower taping head, is mounted  
straight down, as shown in Figure 2-2A. The  
tape drum bracket assembly can be pivoted to  
provide tape roll clearance in certain cases.  
15. Continue with the remainder of the Installation  
and Set-Up procedure through the end of the  
topic.  
13. Remove fasteners that secure case sealer legs  
to pallet.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation and Set-Up (Continued)  
MACHINE BED HEIGHT  
Adjust machine bed height. The case sealer is  
equipped with four adjustable legs that are  
located at the corners of the machine frame.  
The legs can be adjusted to obtain different  
machine bed heights from 610 mm [24 inch]  
minimum to 890 mm [35 inch] maximum.  
1. Useappropriatematerialhandlingequipment  
and blocking techniques to raise the machine  
frame to allow adequate leg adjustment.  
2. Loosen, but do not remove, two M8 x 1.25  
socket head screws in one leg (use M6 hex  
wrench). Adjust the leg length for the desired  
machine bed height. Retighten the two  
screws to secure the leg. Adjust all four legs  
equally.  
Note – Minimum machine bed height can be  
reduced to 520 mm [20.5 inch] by moving  
outer columns up one set of mounting holes.  
However, this change also increases the  
minimum box height of 120 mm [4.8 inch] to  
165 mm [6.5 inch]. (See "Special Set-Up  
Procedure – Box/Machine Bed Height Range".)  
OUTBOARDTAPEROLLMOUNTING  
(LowerTapingHead)  
Refer to Figure 2-2C and set the machine bed  
height as follows:  
Remove the tape drum bracket assembly, spacer  
and fasteners from the lower taping head. Install  
and secure on the infeed end of the lower frame,  
as shown in Figure 2-2B.  
WARNING  
To reduce the risk associated with muscle  
strain:  
Use the appropriate rigging and material  
handling equipment when lifting or  
repositioning this equipment  
Use proper body mechanics when removing  
or installing taping heads that are moderately  
heavy or may be considered awkward to lift  
Figure 2-2 – Machine Bed Height Adjustment and Lower Tape Drum Bracket Position  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation and Set-Up (Continued)  
BOX SIZE CAPACITY OF CASE SEALER  
Use of an extension cord is not recommended.  
However, if one is needed for temporary use, it  
must have a wire size of 1.5 mm diameter  
[AWG 16 ], have a maximum length of 30.5 m  
[100 ft], and must be properly grounded.  
At its factory setting, the case sealer handles box  
sizes up to 620 mm [24.5 inch] maximum height.  
If larger capacity is needed, the machine can be  
adjusted to accommodate boxes up to 725 mm  
[28.5 inch] high. Refer to "Special Set-Up  
Procedure – Box and Machine Bed Height  
Range".  
Note – Adjusting machine to accommodate 725  
mm [28.5 inch] high boxes also increases  
minimum box size to 165 mm [6.5 inch].  
WARNING  
To reduce the risk associated with  
hazardous voltage:  
Position electrical cord away from foot and/or  
vehicletraffic  
ELECTRICAL CONNECTION AND CONTROLS  
The electrical control box (with circuit breaker)  
and "On/Off" switch are located on the lower left  
side of the machine frame. See Figure 3-1. If  
desired, for operator convenience, the "On/Off"  
switch can be relocated to the right side of the  
machine frame. A standard three conductor power  
cord with plug is provided at the back of the  
electrical control box for 115 Volt, 60 Hz.  
electrical service. The receptacle providing this  
service shall be properly grounded. Before the  
power cord is plugged into 115 Volt, 60 Hz outlet  
make sure that all packaging materials and tools  
are removed from the machine. Do not plug  
electrical cord into outlet until ready to run  
machine.  
Note – Machines outside the U.S. may be  
equipped with 220/240 Volt, 50 Hz systems or  
other electrical requirements compatible with  
local practice.  
INITIAL START-UP OF CASE SEALER  
After completing the "Installation and Set-Up"  
procedure, continue through "Operation" for tape  
loading and start-up to be sure case sealer is  
properly adjusted to run boxes  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation  
WARNING  
To reduce the risk associated with mechanical and electrical hazards:  
Read, understand and follow all safety and operating instructions before operating or  
servicing the case sealer  
Refer to Figure 3-1 below to acquaint yourself with the various components and controls of the case sealer. Also see  
Figures 3-1 and 3-2 in Section II for taping head components.  
Figure 3-1 – 700a-s Stainless Steel Case Sealer Components (Left Front View)  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation (Continued)  
Important – Before turning drive belts on, be sure  
no tools or other objects are on the conveyor bed.  
Tape Loading/Threading  
See Section II, Operation Section.  
Electrical "On/Off" Switch  
Note – If lower tape drum is mounted in alternate  
lower outboard position, remove taping head from  
machine bed by pulling straight up, insert  
threading needle in taping head and replace  
taping head. Install tape roll on drum (adhesive on  
tape leg up), thread tape under knurled roller on  
outboard mount, then attach tape to threading  
needle and pull tape through taping head with  
threading needle.  
The box drive belts are turned on and off ("Off"  
button is red) with the electrical switch on the side of  
the machine frame.  
Note – The case sealer has a circuit breaker  
located in the electrical enclosure on the lower left  
side of the machine frame. If circuit becomes  
overloaded and circuit breaker trips, unplug the  
machine electrical cord and determine cause of  
overload. After two minutes, open the electrical  
enclosure and reset the circuit breaker by lifting  
the reset lever. Close the electrical enclosure, plug  
machine electrical cord into outlet and restart  
machine by pressing "I" (On) button.  
WARNING  
To reduce the risk associated with muscle  
strain:  
Emergency Stop Switch  
Use proper body mechanics when removing  
or installing taping heads that are moderately  
heavy or may be considered awkward to lift  
The machine electrical supply can be turned off by  
pressing the latching emergency stop switch. To  
restart machine, rotate emergency stop switch  
(releases switch latch) and then restart machine by  
pressing "I" (On) button on side of machine frame.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation (Continued)  
Box Size Set-Up  
1. ADJUSTUPPERTAPINGHEAD  
The upper taping head is positioned for the box  
height by means of the height adjustment crank  
shown in Figure 3-2. Turn crank clockwise to  
lower head, counterclockwise to raise head.  
Move the top flap compression rollers to a  
position wider than the box.  
Place box on infeed end of machine bed with both  
top and bottom flaps folded and insert under  
upper head ski approximately 150 mm  
[6 inch] as shown in Figure 3-3. Lower the head  
until all flaps are fully closed. Align box top flap  
center seam with arrows on front of upper frame.  
Figure 3-2 – Upper Taping Head  
2. ADJUST SIDE GUIDES (Figure 3-4)  
Align box top flap center seam with arrows on  
front of ski.  
Move side guides against each side of box to  
hold box in position, centered on arrows on front  
of ski.  
Figure 3-3 – Upper Taping Head  
Tighten hand knobs to secure side guides.  
Figure 3-4 – Side Guides  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation (Continued)  
3. RUNBOXESTOCHECKADJUSTMENT  
(Figure3-5)  
Important – Before turning drive belts on, be  
sure no tools or other objects are on the conveyor  
bed.  
CAUTION  
To reduce the risk associated with pinch  
and entanglement hazards:  
Keep hands clear of the upper head support  
assembly as boxes are transported through  
the machine  
Turn electrical switch to "On" to start drive belts.  
Move box forward under upper taping head until it  
is taken away by drive belts. If box is hard to  
move under head or is crushed, raise head  
slightly. If box movement is jerky or stops under  
upper head, lower upper head slightly to add  
more pressure between box and drive belts.  
Figure 3-5 – Check Adjustments  
Note – Upper head has unique feature for  
overstuffed boxes. The head will raise up to  
13 mm [1/2 inch] to compensate for this type  
of condition.  
Important – If drive belts are allowed to slip on  
box, excessive belt wear will occur.  
4. TOP FLAP COMPRESSION ROLLERS  
(Figure3-6)  
CAUTION  
To reduce the risk associated with pinch  
and entanglement hazards:  
Keep hands, hair, loose clothing and jewelry  
away from box compression rollers.  
The top flap compression rollers have two  
mounting positions to provide side compression  
through the full range of box widths.  
Figure 3-6 – Compression Rollers  
The rollers have been pre-assembled in position  
"B" to accommodate box widths from 200 mm  
[8 inch] to 545 mm [21.5 inch] maximum.  
To accommodate box widths less than 200 mm  
[8 inch] to 140 mm [5.5 inch] minimum, move all  
four rollers to position "A".  
Adjust the top flap compression rollers against  
top edge of box and tighten knobs to secure  
rollers in operating position.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation (Continued)  
5. ADJUST COMPRESSION ROLLERS  
Adjust the top flap compression rollers against  
top edge of box and tighten knobs to secure  
rollers in operating position as shown in  
Figure 3-7.  
Box Sealing  
CAUTION  
To reduce the risk associated with pinch  
and entanglement hazards:  
Keep hands clear of the upper head support  
assembly as boxes are transported through  
the machine  
Always feed boxes into the machine by  
Figure 3-7 – Compression Rollers  
pushing only from the end of the box  
Keep hands, hair, loose clothing and jewelry  
away from box compression rollers  
Notes–  
Keep hands, hair, loose clothing, and jewelry  
1. Machine or taping head adjustments are  
described in "Adjustments" Section I for  
machine or Section II for taping heads.  
away from moving belts and taping heads  
WARNING  
2. Box drive motors are designed to run at a  
moderate temperature of 40°C [104°F]. In  
some cases, they may feel hot to the  
touch.  
To reduce the risk associated with pinch,  
entanglement, and hazardous voltage:  
Never attempt to work on any part of the  
machine, load tape, or remove jammed boxes  
from the machine while the machine is  
running  
1. Feed boxes to machine at minimum 455 mm  
[18 inch] intervals.  
2. Reload and thread tape as necessary.  
3. Be sure machine is cleaned and lubricated  
according to recommendations in "Maintenance"  
section of this manual.  
WARNING  
To reduce the risk associated with pinch  
and entanglement hazards:  
Do not leave the machine running while  
unattended  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance  
The case sealer has been designed for long, trouble  
free service. The machine will perform best when it  
receives routine maintenance and cleaning. Machine  
components that fail or wear excessively should be  
promptly repaired or replaced to prevent damage to  
other portions of the machine or to the product.  
Lubrication  
Most of the machine bearings, including the drive  
motor, are permanently lubricated and sealed and do  
not require additional lubricant.  
Figure 4-1 illustrates the machine points that do  
require lubrication every 250 hours of operation.  
Lubricate the points indicated by arrows (  
small amount of multi-purpose grease.  
) with a  
WARNING  
To reduce the risk associated with  
Note – Wipe off excess oil and grease. It will attract  
dust which can cause premature equipment wear  
and jamming. Take care that oil and grease are not  
left on the surface of rollers around which tape is  
threaded, as it can contaminate the tape's adhesive.  
mechanical and electrical hazards:  
Read, understand and follow all safety and  
operating instructions before operating or  
servicing the case sealer  
Allow only properly trained and qualified  
personnel to operate and/or service this  
equipment  
Turn electrical supply off and disconnect  
beforeperforminganyadjustments,  
maintenance or servicing the machine or  
tapingheads  
Cleaning  
Note – Never attempt to remove dirt from the machine  
by blowing it out with compressed air. This can cause  
the dirt to be blown inside the motor and onto sliding  
surfaces which may cause premature equipment  
wear. Never wash down this equipment. Serious  
equipment damage could result.  
Regular slotted containers produce a great deal of  
dust and paper chips when processed or handled in  
equipment. If this dust is allowed to build-up on  
machine components, it can cause component wear  
and overheating of drive motor. The dust build-up can  
best be removed from the machine by a shop vacuum.  
Depending on the number and type of boxes sealed in  
the case sealer, this cleaning should be done approxi-  
mately once per month. If the boxes sealed are dirty,  
or if the environment in which the machine operates is  
dusty, cleaning on a more frequent basis may be  
necessary. Excessive dirt build-up that cannot be  
removed by vacuuming should be wiped off with a  
damp cloth.  
Figure 4-1 – Lubrication Points – Frame  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance (Continued)  
WARNING  
To reduce the risk associated with mechanical and electrical hazards:  
Turn electrical supply off and disconnect before performing any adjustments, maintenance or servicing the  
machine or taping heads  
Box Drive Belt Replacement  
Note – 3M recommends the replacement of drive  
belts in pairs, especially if belts are unevenly worn.  
LOWER DRIVE BELTS  
Figure4-2  
1. Remove and retain center plate (A) and four  
screws.  
2. Remove and retain side cover (B) and fasteners.  
3. Loosen, but do not remove lock nut (C).  
4. Loosen tension screw (D) until all belt tension is  
removed.  
5. Pull belt splicing pin (E) out and remove belt.  
6. Place new belt over pulleys with laced splice at  
top. Insert splicing pin.  
Important – Pin must not extend beyond edge of  
belt.  
Figure 4-2 – Lower Drive Belt Replacement  
7. Adjust belt tension as explained in "Adjustments  
- Box Drive Belt Tension."  
8. Replace side cover and center plate and secure  
with original fasteners.  
UPPER DRIVE BELTS  
Figure 4-3  
1. Remove and retain front cover (A) and four  
screws.  
2. Loosen, but do not remove lock nut (C).  
3. Loosen tension screw (D) until all tension is  
removed from belt.  
4. Move compression roller assembly out to full  
open position.  
5. Remove 4 screws on side of belt guard (E) and  
slide belt guard out to expose belt.  
6. Pull belt splicing pin (F) out and remove belt.  
7. Place new belt over pulleys with laced splice at  
top. Insert splicing pin.  
Important – Pin must not extend beyond edge of  
belt.  
8. Adjust belt tension as explained in "Adjustments  
– Box Drive Belt Tension."  
Figure 4-3 – Upper Drive Belt Replacement  
9. Replace front cover and belt guard(s) and  
secure with original fasteners.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance (Continued)  
WARNING  
To reduce the risk associated with mechanical and electrical hazards:  
Turn electrical supply off and disconnect before performing any adjustments, maintenance or servicing the  
machine or taping heads  
Circuit Breaker  
Blade Replacement, Taping Head  
The case sealer is equipped with a circuit breaker  
which trips if the motors are overloaded. Located  
inside the electrical enclosure on the side of the  
machine frame just below the machine bed, the  
circuit breaker has been pre-set at 3.4 amps and  
requires no further maintenance.  
See Section II, "Maintenance – Blade Replacement."  
If circuit is overloaded and circuit breaker trips,  
unplug machine from electrical power:  
1. Determine cause of overload and correct.  
2. Remove electrical enclosure cover.  
3. Press "Reset" and then press "On" button.  
If circuit breaker will not reset, wait 2  
minutes and retry.  
4. Replace cover.  
5. Plug in machine.  
6. Press machine "On" button to resume case  
sealing.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjustments  
WARNING  
To reduce the risk associated with mechanical and electrical hazards:  
Turn electrical supply off and disconnect before performing any adjustments, maintenance or servicing the  
machine or taping heads  
Box Drive Belt Tension  
The four continuously moving drive belts convey boxes through the tape applying mechanism. The box drive belts  
are powered by an electric motor.  
Tension adjustment of these belts may be required during normal operation. Belt tension must be adequate to  
positively move the box through the machine and the belts should run fully on the surface of the pulleys at each end  
of the frame. The idler pulleys on the infeed end are adjusted in or out to provide proper belt tension. Each belt is  
adjusted separately.  
Belt tension is obtained by tightening the adjustment screw so that a moderate pulling force of 3.5 kg [7 lbs.]  
applied at the midspan, as shown in Figure 5-1, will deflect the belt 25 mm [1 inch]. This will assure positive contact  
between the belt and the drive pulley on the discharge end of the drive assembly.  
Note – Figure 5-1 illustrates the lower drive belts; however, upper belts are adjusted in the same manner.  
Figure 5-1 – Box Drive Belt Tension Adjustment  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjustments (Continued)  
WARNING  
To reduce the risk associated with mechanical and electrical hazards:  
Turn electrical supply off and disconnect before performing any adjustments, maintenance or servicing the  
machine or taping heads  
Refer to Figure 5-2 and 5-3 and adjust belt tension as follows:  
1. Remove and retain center plate/front cover and four screws.  
2. Loosen, but do not remove, M10 lock nut with a 17 mm open end wrench.  
3. Reset the tension on the drive belts as needed. Adjust the M8 tension screws in (clockwise) to increase  
tension or out (counterclockwise) to decrease tension. Tighten lock nut to secure tension setting.  
4. Replace center plate/front cover and secure with original screws.  
Figure 5-2 – Box Drive Belt Tension Adjustment, Lower Belts (Infeed End)  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjustments (Continued)  
WARNING  
To reduce the risk associated with mechanical and electrical hazards:  
Turn electrical supply off and disconnect before performing any adjustments, maintenance or servicing the  
machine or taping heads  
Figure 5-3 – Box Drive Belt Tension Adjustment, Upper Belts (Infeed End)  
Taping Head Adjustments – Refer to Section II.  
WARNING  
To reduce the risk associated with sharp blade hazards:  
Keep hands and fingers away from tape cutoff blades under orange blade guards. The blades are extremely  
sharp  
TAPE WEB ALIGNMENT – Section II  
TAPE DRUM FRICTION BRAKE – Section II  
APPLYING MECHANISM SPRING – Section II  
ONE-WAY TENSION ROLLER – Section II  
TAPE LEG LENGTH ADJUSTMENT – Section II  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Special Set-Up Procedure  
WARNING  
To reduce the risk associated with mechanical and electrical hazards:  
Turn electrical supply off and disconnect before performing any adjustments, maintenance or servicing the  
machine or taping heads  
Figure 6-1 – Case Sealer Frame Changes  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Special Set-Up Procedure (Continued)  
WARNING  
To reduce the risk associated with mechanical and electrical hazards:  
Turn electrical supply off and disconnect before performing any adjustments, maintenance or servicing the  
machine or taping heads  
TAPING HEAD REMOVAL  
WARNING  
To reduce the risk associated with sharp blade hazards:  
Keep hands and fingers away from tape cutoff blades under orange blade guards. The blades are extremely  
sharp  
1. Remove tape from upper taping head and raise upper assembly to a convenient working height.  
2. Pivot up the clamp that secures the upper taping head as shown in Figure 6-1B.  
3. Hold upper taping head applying and buffing arms from under upper assembly, slide head forward and down  
to remove. See Figure 6-2.  
CAUTION  
To reduce the risk associated with muscle strain:  
Use proper body mechanics when removing or installing taping heads that are moderately heavy or may be  
considered awkward to lift  
4. Raise upper assembly to provide working room around lower taping head and remove tape from taping  
head.  
5. Lift the lower taping head, shown in Figure 6-3 and 6-1C, straight up to remove it from the case sealer bed.  
6. Replace taping heads reverse of disassembly.  
Figure 6-2 – Remove Upper Taping Head  
Figure 6-3 – Remove Lower Taping Head  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Special Set-Up Procedure (Continued)  
Box and Machine Bed Height Range – Refer to Figure 6-4  
Moving the outer columns up one set of mounting holed increases the maximum box size handled by the  
700a-s case sealer and decreases the minimum machine bed height.  
Note – This also increases the minimum box height from 120 mm [4.8 inch] to 165 mm [6.5 inch].  
To move the outer columns up one set of mounting holes:  
WARNING  
To reduce the risk associated with muscle strain:  
Use the appropriate rigging and material handling equipment when lifting or repositioning this equipment  
Use proper body mechanics when removing or installing taping heads that are moderately heavy or may be  
considered awkward to lift  
1. Place minimum 305 mm [12 inch] high blocks at the front and rear of the upper taping head assembly as shown  
in Figure 6-4A. Crank the upper taping head assembly down until it touches these blocks.  
Important – Blocks (front and rear) must be same height in order to keep upper taping head assembly parallel  
with machine bed/drive belts.  
2. Remove and retain the six screws and plain washers that fasten each column to the frame. Figure 6-4B.  
3. Turn the height adjustment crank clockwise to raise the outer columns up one set of mounting holes  
(100 mm [4 inch]).  
4. Install and tighten the six screws and plain washers in each column that were removed in Step 2. Crank upper  
taping head assembly up and remove blocks.  
If desired, the bed height can now be decreased to 520 mm [20.5 inch] by adjusting legs upward. (See "Installation  
and Set-Up – Machine Bed Height".)  
Figure 6-4 – Box and Machine Bed Height Range  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
The Troubleshooting Guide lists some possible machine problems, causes and corrections. Also see Section II  
"Troubleshooting"fortapingheadproblems.  
Troubleshooting Guide  
Problem  
Cause  
Correction  
Drive belts do not convey boxes  
Narrow boxes  
Check machine specifications.  
Boxes are narrower than  
recommended, causing slippage  
and premature belt wear.  
Worn drive belts  
Replace drive belts  
Top taping head does not apply  
enough pressure  
Adjust the box height adjustment  
with the crank  
Top flap compression rollers in too  
tight  
Readjust compression rollers  
Replace spring holder  
Taping head applying spring  
holder missing  
Taping head applying spring set  
too high  
Reduce spring pressure  
Drive belts do not turn  
Worn or missing friction rings  
Drive belt tension too low  
Electrical disconnect  
Replace friction rings  
Adjust belt tension  
Check power and electrical plug  
Set to correct current value  
Circuit breaker not at correct  
setting  
Motor not turning  
Evaluate problem and correct  
Upper and lower applying  
mechanisms interfere with each  
other  
Machine's minimum height stop  
does not match tape head leg  
length setting  
Check manual to make sure  
taping heads match machine  
setting  
Drive belts break  
Worn belt  
Replace belt  
Light boxes tip back on exit  
Upper ski down too far  
Dry compression rollers  
Dry column bearings  
Defective column bearings  
Carefully adjust upper ski  
Lubricate compression rollers  
Lubricate column bearings  
Replace column bearings  
Squeaking noise as boxes pass  
through machine  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Electrical Diagram  
WARNING  
To reduce the risk associated with mechanical and electrical hazards:  
Turn electrical supply off and disconnect before performing any adjustments, maintenance or servicing the  
machine or taping heads  
Figure 7-1 – Electrical Diagram  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacement Parts And Service Information  
Spare Parts  
It is suggested that the following spare parts be ordered and kept on hand:  
Qty.  
Ref. No.  
Part Number  
Description  
4
10426-85&10427-70  
78-8070-1531-4  
Belt - Drive W/Pin  
Also see Section II for recommended taping head spare parts.  
Label Kit  
In the event that any labels are damaged or destroyed, they must be replaced to ensure operator safety. A  
label kit, part number 78-8098-9175-3 is available as a stock item. It contains all the safety labels used on the  
700a-s Adjustable Case Sealer.  
Tool Kit  
A tool kit, part number 78-8060-8476-6, is available as a stock item. The kit contains the necessary open end and  
hex socket wrenches for use with the metric fasteners on the case sealer. The threading tool, part number  
78-8076-4726-4, contained in above kit is also available as a replacement stock item.  
Replacement Parts Ordering Information and Service  
Refer to the first page of this instruction manual "Replacement Parts and Service Information".  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Options/Accessories  
For additional information on the options/accessories listed below, contact your 3M Representative.  
Part Number  
Option/Accessory  
78-8052-6553-1  
70-0064-0379-7  
70-0064-0378-9  
78-8060-8156-4  
78-8060-8157-2  
Box Hod Down Attachment, Model 18500  
Caster Kit Attachment  
Conveyor Extension Attachment  
AccuGlide SST 2 Inch Upper Taping Head, Type 18900  
AccuGlide SST 2 Inch Lower Taping Head, Type 18900  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacement Parts – Illustrations and Parts Lists  
700a-s Stainless Steel Adjustable Case Sealer, Type 10500  
Frame Assemblies  
To Order Parts:  
1. Refer to first illustration, Frame Assemblies, for the Figure Number that identifies a specific portion of the  
machine.  
2. Refer to the appropriate Figure or Figures to determine the parts required and the parts reference number.  
3. The Parts List that follows each illustration, includes the Reference Number, Part Number and Part  
Description for the parts on that illustration.  
Note – The complete description has been included for standard fasteners and some commercially  
available components. This has been done to allow obtaining these standard parts locally, if desired.  
4. Order parts by Part Number, Part Description and Quantity required. Also include machine name, number  
and type.  
5. Refer to the first page of this instruction manual “Replacement Parts and Service Information” for  
replacementpartsorderinginformation.  
Important – Not all the parts listed are normally stocked items. Some parts or assemblies shown are  
available only on special order. Contact 3M/Tape Dispenser Parts to confirm item availability.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
700a-s Stainless Steel Adjustable Case Sealer  
Frame Assemblies  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
700a-s Stainless Steel Adjustable Case Sealer  
Figure 10428  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 10428  
Ref. No.  
3M Part No.  
Description  
10428-1  
10428-2  
10428-3  
10428-4  
10428-5  
10428-6  
78-8070-1536-3  
78-8060-8292-7  
78-8060-8312-3  
78-8060-1976-5  
78-8134-1977-3  
78-8060-8326-3  
78-8134-1978-1  
78-8017-9074-8  
78-8060-8339-6  
78-8070-1540-5  
78-8134-1979-9  
78-8134-1980-7  
78-8134-1981-5  
78-8134-1982-3  
78-8076-4505-2  
78-8134-1983-1  
78-8134-1984-9  
78-8070-1546-2  
78-8134-1985-6  
78-8134-1986-4  
78-8070-1548-8  
78-8134-1987-2  
78-8060-8315-6  
78-8070-1549-6  
78-8134-1988-0  
78-8060-8295-0  
Support - Guide Arm  
Screw - Hex.Hd, M6x12  
Washer - Flat, M6  
Lever - Pivot  
Bushing  
Set Screw - M5x6  
Link - Guide  
10428-7  
10428-8  
10428-9  
10428-10  
10428-11  
10428-12  
10428-13  
10428-14  
10428-15  
10428-16  
10428-17  
10428-19  
10428-20  
10428-21  
10428-22  
10428-23  
10428-24  
10428-25  
10428-26  
10428-27  
Washer - Nylon, 15 mm  
Ring - M10  
Support - Lever  
Screw - Soc.Hd, M5x16  
Guide Arm - Front, Right  
Guide Arm - Front, Left  
Guide Arm - Rear  
Set Screw - M6x8  
Guide - R/H  
Guide - L/H  
Cap - Guide  
Screw - Soc.Hd, M5x30  
Shaft - Guide  
Washer - Nylon, 20 mm  
Screw - Hex.Hd, M10x40  
Washer - Flat, M10  
Knob  
Washer - Flat, M5  
Screw - Hex.Hd, M6x16  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
700a-s Stainless Steel Adjustable Case Sealer  
Figure 10422  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 10422  
Ref. No.  
3M Part No.  
Description  
10422-1  
10422-2  
10422-3  
10422-4  
10422-5  
10422-6  
10422-7  
10422-8  
10422-9  
10422-10  
10422-11  
10422-12  
78-8134-1900-5  
78-8134-1901-3  
78-8076-4628-2  
78-8134-1902-1  
78-8060-8323-0  
78-8060-8308-1  
78-8134-1903-9  
78-8134-1904-7  
78-8134-1905-4  
78-8017-9074-8  
78-8060-8315-6  
78-8070-1549-6  
Side Compression Rollers Assy  
Support - Roller  
Roller - Compression  
Shaft - Roller  
Screw - Hex.Hd. M8x16  
Washer - Flat, M8  
Plate - Tube  
Screw - Carriage, M10x35  
Cap - Support  
Washer - Nylon  
Washer - Flat, M10  
Knob  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
700a-s Stainless Steel Adjustable Case Sealer  
Figure 10425  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 10425  
Ref. No.  
3M Part No.  
Description  
10425-1  
10425-2  
10425-3  
10425-4  
10425-5  
10425-6  
10425-7  
10425-8  
10425-9  
10425-10  
10425-11  
10425-12  
10425-13  
10425-14  
10425-15  
10425-16  
10425-17  
10425-18  
10425-19  
10425-20  
10425-21  
78-8134-1933-6  
78-8134-1934-4  
78-8134-1935-1  
78-8134-1936-9  
78-8070-1568-6  
78-8134-1937-7  
78-8134-1938-5  
78-8076-4730-6  
78-8052-6749-5  
78-8060-8362-8  
78-8060-8337-0  
78-8060-8172-1  
78-8134-1939-3  
78-8134-1940-1  
78-8060-8201-8  
78-8060-8295-0  
78-8134-1941-9  
78-8060-8312-3  
78-8060-8292-7  
78-8134-1942-7  
78-8060-8315-6  
Tape Roll Bracket Assy  
Tape Drum Bracket Assy  
Bracket - Tape Drum, Upper  
Bracket - Tape Drum, Lower  
Cap - Bracket  
Shaft - Tape Drum  
Nut - M18x1  
Tape Drum Assy - 2" Wide  
Tape Drum  
Leaf spring  
Screw - Self Tapping, 7SPx8  
Washer - Friction  
Washer - Tape Drum  
Spring - Tape Drum  
Nut - Self Locking, M10x1  
Screw - Hex.Hd, M6x16  
Spacer  
Washer - Flat, M6  
Screw - Hex.Hd, M6x12  
Tape Drum Assy - 2" Wide  
Washer - Flat, M10  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
700a-s Adjustable Case Sealer  
Figure 10429  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 10429  
Ref. No.  
3M Part No.  
Description  
10429-1  
78-8134-1989-8  
78-8134-1990-6  
78-8134-1991-4  
78-8060-8319-8  
78-8060-8308-1  
78-8134-1992-2  
78-8134-1993-0  
78-8060-8480-8  
78-8134-1994-8  
78-8060-8320-6  
78-8134-1995-5  
78-8060-8332-1  
78-8060-8481-6  
78-8060-8195-2  
78-8060-8196-0  
78-8134-1996-3  
78-8134-1997-1  
78-8134-1998-9  
78-8060-8485-7  
78-8060-8295-0  
78-8060-8312-3  
78-8060-8331-3  
78-8076-4620-9  
78-8060-8486-5  
78-8060-8290-1  
78-8134-1999-7  
78-8134-2000-3  
78-8060-8293-5  
78-8134-1974-0  
78-8060-8401-4  
78-8060-8303-2  
78-8076-4701-7  
78-8060-8404-8  
78-8134-2294-2  
78-8060-8405-5  
78-8060-8406-3  
78-8060-8304-0  
78-8060-8407-1  
Conveyor Bed Assembly  
Bed – Conveyor  
Support – Drive  
10429-2  
10429-3  
10429-4  
Screw – Hex Hd, M8 x 20  
Washer – Plain, 8 mm  
Leg Assembly – Inner  
Leg – Inner  
10429-5  
10429-6  
10429-7  
10429-8  
Pad – Foot  
10429-9  
Screw – Hex Hd, M8 x 30  
Nut – Self Locking, M8  
Stop – Leg  
10429-10  
10429-11  
10429-12  
10429-13  
10429-14  
10429-15  
10429-16  
10429-17  
10429-18  
10429-19  
10429-20  
10429-21  
10429-22  
10429-23  
10429-24  
10429-25  
10429-26  
10429-27  
10429-28  
10429-29  
10429-30  
10429-31  
10429-32  
10429-33  
10429-34  
10429-35  
10429-36  
10429-37  
10429-38  
Screw – Soc Hd, M8 x 16  
Label – Height  
Clamp – Inner  
Clamp – Outer  
Support assy - Tape Bracket  
Support  
Shaft - Roller  
Roller  
Screw – Hex.Hd, M6 x 16  
Washer – Flat, M6  
Screw – Soc Hd, M6 x 16  
Plane – Conveyor Bed  
Bushing  
Screw – Soc Hd, M6 x 25  
Cover – Switch  
Screw – M5 x 10  
Nut – M5  
Screw – Hex Hd, M5 x 20  
Washer – Special  
Washer – Flat, M5  
Cap /28  
Caster Assembly  
Caster /80  
Spacer - Caster  
Washer /12-45, 5x4  
Washer – Flat, M12  
Nut – Self Locking, M12  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
700a-s Stainless Steel Adjustable Case Sealer  
Figure 10423  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1Figure 10423  
Ref. No.  
3M Part No.  
Description  
10423-1  
10423-2  
10423-3  
10423-4  
10423-5  
10423-6  
10423-7  
10423-8  
78-8134-1906-2  
78-8134-1907-0  
78-8060-8307-3  
78-8060-8308-1  
78-8060-8491-5  
78-8134-1908-8  
78-8060-8297-6  
78-8134-1909-6  
78-8134-1910-4  
78-8134-1911-2  
78-8134-1912-0  
78-8134-1913-8  
78-8054-8617-8  
78-8060-8272-9  
78-8060-8318-0  
78-8134-1914-6  
78-8134-1915-3  
78-8054-8970-1  
78-8054-8571-7  
78-8060-8284-4  
78-8060-8271-1  
78-8060-8343-8  
78-8134-1916-1  
78-8054-8583-2  
78-8134-1917-9  
78-8134-1918-7  
78-8060-8498-0  
78-8134-1919-5  
78-8060-8310-7  
78-8134-1920-3  
78-8134-1921-1  
78-8060-8295-1  
78-8070-1503-3  
78-8060-8296-8  
78-8060-8204-2  
78-8060-8312-3  
78-8134-1922-9  
78-8100-0905-6  
78-8070-1505-8  
78-8070-1506-6  
78-8134-1923-7  
78-8076-5422-9  
78-8134-1924-5  
78-8060-8327-1  
78-8070-1510-8  
78-8134-1925-2  
78-8070-1512-4  
78-8076-4800-7  
78-8134-1926-0  
78-8134-1927-8  
78-8054-8821-6  
78-8060-8335-4  
Column Assy - Outer  
Plate - Column Mounting  
Screw - Soc.Hd, M8x20  
Washer - Flat, M8  
Cap - Column  
Screw - Self Tapping, 8Px13  
Washer - Flat, M4  
Stop - Height  
Plate - Nut Stop  
Screw - Pan Hd., M5x12  
Column Assy - Inner  
Column - Inner  
Bearing - Special  
Screw - Special  
Nut - Self Locking, M6  
Lead Screw  
Spring  
Bed Plate - Spring  
Plastic Nut  
Nut - Special  
Collar  
Pin  
Bearing  
Bushing  
Bushing - Lead Screw  
Set Screw - M6x8  
Bushing - Inner Ccolumn  
Sprocket - 3/8", P=13  
Screw - Soc.Hd. M4x25  
Chain - 3/8", P=156  
Housing - Chain  
Idler Screw  
Roller - Chain Tensioning  
Washer - Triple, M6  
Screw - Special, M6x12  
Washer - Flat, M6  
Cover  
10423-9  
10423-10  
10423-11  
10423-12  
10423-13  
10423-14  
10423-15  
10423-16  
10423-17  
10423-18  
10423-19  
10423-20  
10423-21  
10423-22  
10423-23  
10423-24  
10423-25  
10423-26  
10423-27  
10423-28  
10423-29  
10423-30  
10423-31  
10423-32  
10423-33  
10423-34  
10423-35  
10423-36  
10423-37  
10423-38  
10423-39  
10423-40  
10423-41  
10423-42  
10423-43  
10423-44  
10423-45  
10423-46  
10423-47  
10423-48  
10423-49  
10423-50  
10423-51  
10423-52  
Screw - Hex.Hd. M4x10  
Cap - Inner Column  
Cover - Screw  
Crank Assy  
Crank  
Shaft - Crank  
Screw - Flat Hd, M5x16  
Washer - Nylon  
Bushing  
Knob  
Washer - Crank, Lower  
Washer - Crank, Upper  
Key - Stop  
Cap  
Washer - Triple, M8  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
700a-s Stainless Steel Adjustable Case Sealer  
Figure 10426/1 of 2  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 10426 (Page 1 of 2)  
Ref. No.  
3M Part No.  
Description  
10426-1  
10426-2  
10426-3  
10426-4  
10426-5  
10426-6  
10426-7  
10426-8  
78-8134-1943-5  
78-8134-1944-3  
78-8134-1944-3  
78-8060-8333-9  
78-8134-1945-0  
78-8134-1946-8  
78-8060-8306-5  
788134-1947-6  
78-8060-8292-7  
78-8060-8312-3  
78-8134-1948-4  
78-8052-6641-4  
78-8070-1592-6  
78-8134-1949-2  
78-8134-1950-0  
78-8060-8308-1  
78-8060-7693-7  
78-8070-1593-4  
78-8060-8325-5  
78-8060-8303-2  
78-8134-1951-8  
78-8134-1952-6  
78-8060-8307-3  
78-8134-1953-4  
78-8052-6652-1  
78-8134-1954-2  
78-8134-1955-9  
78-8134-1956-7  
78-8134-1957-5  
78-8052-6710-7  
78-8060-8248-9  
78-8060-8294-3  
78-8060-8331-3  
78-8134-1958-3  
78-8060-8328-9  
78-8134-1959-1  
78-8060-8391-7  
78-8060-8282-8  
78-8060-8281-0  
78-8060-8330-5  
78-8060-8372-7  
78-8060-8373-5  
78-8060-8336-2  
78-8060-8279-4  
78-8060-8269-5  
78-8060-8243-0  
78-8060-8299-2  
78-8060-8301-6  
Drive Assy -Ttop, W/O Motor  
Frame - Top Drive  
Guide - Drive Belt  
Screw - Flat Hd, M5x20  
Clamp - Upper Head  
Shaft - Roller  
Screw - Soc.Hd, M5x10  
Spacer  
Screw - Hex.Hd, M6x12  
Washer - Flat, M6  
Tube - Roller  
Roller  
Spacer - Roller  
Shaft - Roller  
Nut - Special, M8  
Washer - FLat, M8  
Roller  
10426-9  
10426-10  
10426-11  
10426-12  
10426-13  
10426-14  
10426-15  
10426-16  
10426-17  
10426-18  
10426-19  
10426-20  
10426-21  
10426-22  
10426-23  
10426-24  
10426-25  
10426-26  
10426-27  
10426-28  
10426-29  
10426-30  
10426-31  
10426-32  
10426-33  
10426-34  
10426-35  
10426-36  
10426-37  
10426-40  
10426-41  
10426-42  
10426-44  
10426-45  
10426-46  
10426-47  
10426-48  
10426-49  
10426-50  
10426-51  
Spacer - Roller  
Screw - Hex.Hd, M5x12  
Washer - Flat, M5  
Support - Roller  
Bracket - Compression Roller  
Screw - Soc.Hd, M8x20  
Screw - Soc.Hd, M8x40  
Cap  
Belt Tensioning Assy - R/H  
Belt Tensioning Assy - L/H  
Belt Tensioning - R/H  
Belt Tensioning - L/H  
Roller - Idler  
Washer - Special  
Washer - Lock, M6  
Screw - Soc.Hd, M6x16  
Spacer - Shaft  
Nut - Self Locking M10  
Screw - Hex.Hhd, M6x60  
Gearbox Assy - W/O Motor  
Spacer  
Spacer  
Screw - Flat Hd, M5x12  
Pulley - Timing Belt  
Support - Pulley  
Key 4x4x10  
Sprocket - 3/8", 11 Teeth  
Washer - 5,5/20x4  
Washer - 6,5/30x5  
Screw - Flat Hd, M6x16  
Screw - Hex.Hd, M6x20  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
700a-s Stainless Steel Adjustable Case Sealer  
Figure 10426/2 of 2  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 10426 (Page 2 of 2)  
Ref. No.  
3M Part No.  
Description  
104-26-52  
104-26-54  
104-26-55  
104-26-56  
104-26-57  
104-26-58  
104-26-59  
104-26-60  
104-26-61  
104-26-62  
104-26-63  
104-26-64  
104-26-65  
104-26-67  
104-26-68  
104-26-69  
104-26-70  
104-26-71  
104-26-72  
104-26-73  
104-26-74  
104-26-76  
104-26-77  
104-26-78  
104-26-79  
104-26-80  
104-26-81  
104-26-82  
104-26-83  
104-26-84  
104-26-85  
104-26-86  
104-26-87  
104-26-88  
104-26-89  
104-26-90  
104-26-91  
104-26-92  
104-26-99  
104-26-100  
104-26-101  
104-26-102  
104-26-103  
104-26-104  
104-26-105  
78-8060-8296-8  
78-8060-8370-1  
78-8060-8280-2  
78-8060-8314-9  
78-8060-8320-6  
78-8057-5808-9  
78-8057-5724-8  
78-8060-8283-6  
78-8060-8326-3  
78-8060-8302-4  
78-8060-8335-4  
78-8060-8302-4  
78-8060-8289-3  
78-8060-8277-8  
78-8060-8316-4  
78-8060-83131  
78-8060-8278-6  
78-8060-8374-3  
78-8060-8352-9  
78-8060-8345-3  
78-8060-8233-1  
78-8060-8322-2  
78-8076-4585-4  
78-8076-4586-2  
78-8060-8322-2  
78-8060-8371-9  
78-8052-6713-1  
78-8060-8351-1  
78-8134-1960-9  
78-8076-4702-5  
78-8070-1531-4  
78-8134-1961-7  
78-8134-1962-5  
78-8134-1963-3  
78-8134-1964-1  
78-8134-1965-8  
78-8134-1966-6  
78-8076-4994-8  
78-8076-5372-6  
78-8076-4532-6  
78-8114-4601-8  
78-8134-1967-4  
78-8060-8230-7  
78-8060-8231-5  
78-8060-8232-3  
Washer - Triple, M6  
Pulley - Reducer  
Shaft - Pulley  
E-ring - 10 mm  
Nut - Self Locking M8  
Belt - Timing, 187L100  
Belt - Timing, 187L050  
Pulley - Timing, 11 teeth  
Set Screw - M5x6  
Screw - Hex.Hd, M8x25  
Washer - Triple, M8  
Lockwasher - M8  
Nut - M8  
Sprocket - 3/8", 28 teeth  
Key 6x6x20  
Key 5x5x30  
Bushing  
Flange - Shaft  
Shaft - Drive  
Chain - 3/8", 57 pitch  
Cover - Top  
Screw - Soc.Hd, M5x12  
Support - Bearing, R/H  
Support - Bearing, L/H  
Screw - Soc.Hd, M5x12  
Pulley Assy - Drive  
Ring - Pulley  
Nut - Self Locking, M20x1  
Bracket  
Grommet /28  
Belt - Drive, Laced  
Cover - Upper, Front  
Screw - Pan Hd., M5x10  
Guard - Belt, R/H  
Guard - Belt, L/H  
Screw - Pan Hd., M5x16  
Washer - Special  
Motor - 110V 60Hz 1Ph, IP56  
Fan - Motor  
Cord Grip ST11  
Gasket  
Stud - Mounting  
Frame - R/H  
Frame - L/H  
Cover - Bottom  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
700a-s Stainless Steel Adjustable Case Sealer  
Figure 10427/1 of 2  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 10427 (Page 1 of 2)  
Ref. No.  
3M Part No.  
Description  
10427-1  
78-8134-1969-0  
78-8134-1970-8  
78-8134-1947-6  
78-8060-8292-7  
78-8134-1954-2  
78-8134-1955-9  
78-8134-1956-7  
78-8134-1957-5  
78-8052-6710-7  
78-8060-8248-9  
78-8060-8294-3  
78-8060-8331-3  
78-8134-1958-3  
78-8060-8328-9  
78-8134-1971-6  
78-8060-8308-1  
78-8134-1944-3  
78-8060-8333-9  
78-8060-8391-7  
78-8060-8282-8  
78-8060-8281-0  
78-8060-8325-5  
78-8060-8303-2  
78-8060-8330-5  
78-8060-8372-7  
78-8060-8373-5  
78-8060-8336-2  
78-8060-8279-4  
78-8060-8269-5  
78-8060-8243-0  
78-8060-8299-2  
78-8060-8301-6  
78-8060-8296-8  
78-8060-8370-1  
78-8060-8280-2  
78-8060-8314-9  
78-8060-8320-6  
78-8057-5808-9  
78-8057-5724-8  
78-8060-8283-6  
78-8060-8326-3  
Drive Assy - Bottom, W/O Motor  
Frame - Bottom Drive  
Spacer  
10427-2  
10427-3  
10427-4  
Screw - Hex.Hd, M6x12  
Belt Tensioning Assy - R/H  
Belt Tensioning Assy - L/H  
Belt Tensioning - R/H  
Belt Tensioning - L/H  
Roller - Idler  
10427-5  
10427-6  
10427-7  
10427-8  
10427-9  
10427-10  
10427-11  
10427-12  
10427-13  
10427-14  
10427-15  
10427-16  
10427-17  
10427-18  
10427-19  
10427-22  
10427-23  
10427-24  
10427-25  
10427-26  
10427-28  
10427-29  
10427-30  
10427-31  
10427-32  
10427-33  
10427-34  
10427-35  
10427-36  
10427-38  
10427-39  
10427-40  
10427-41  
10427-42  
10427-43  
10427-44  
10427-45  
Washer - Special  
Washer - Lock, M6  
Screw - Soc.Hd, M6x16  
Spacer - Shaft  
Nut - Self Locking M10  
Screw - Soc.Hd, M8x70  
Washer - Flat, M8  
Guide - Drive Belt  
Screw - flat hd, M5x20  
Gearbox Assy - W/O Motor  
Spacer  
Spacer  
Screw - Hex.Hd, M5x12  
Washer - Flat, M5  
Screw - Flat Hd, M5x12  
Pulley - Timing Belt  
Support - Pulley  
Key 4x4x10  
Sprocket - 3/8", 11 teeth  
Washer - 5,5/20x4  
Washer - 6,5/30x5  
Screw - Flat Hd, M6x16  
Screw - Hex.Hd, M6x20  
Washer - Triple, M6  
Pulley - Reducer  
Shaft - Pulley  
E-ring - 10 mm  
Nut - Self Locking M8  
Belt - Timing, 187L100  
Belt - Timing, 187L050  
Pulley - Timing, 11 teeth  
Set Screw - M5x6  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
700a-s Stainless Steel Adjustable Case Sealer  
Figure 10427/2 of 2  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 10427 (Page 2 of 2)  
Ref. No.  
3M Part No.  
Description  
10427-46  
10427-47  
10427-48  
10427-49  
10427-51  
10427-52  
10427-53  
10427-54  
10427-55  
10427-56  
10427-57  
10427-58  
10427-60  
10427-61  
10427-62  
10427-63  
10427-64  
10427-65  
10427-66  
10427-67  
10427-68  
10427-69  
10427-70  
10427-71  
10427-72  
10427-73  
10427-74  
10427-75  
10427-76  
10427-77  
10427-78  
10427-85  
10427-86  
10427-87  
10427-88  
10427-89  
10427-90  
78-8060-8302-4  
78-8060-8335-4  
78-8060-8302-4  
78-8060-8289-3  
78-8060-8277-8  
78-8060-8316-4  
78-8060-8313-1  
78-8060-8278-6  
78-8060-8374-3  
78-8060-8352-9  
78-8060-8345-3  
78-8060-8233-1  
78-8060-8322-2  
78-8076-4585-4  
78-8076-4586-2  
78-8060-8322-2  
78-8134-1972-4  
78-8060-8292-7  
78-8060-8312-3  
78-8060-8371-9  
78-8052-6713-1  
78-8060-8351-1  
78-8070-1531-4  
78-8070-1584-3  
78-8076-4618-3  
78-8060-8267-9  
78-8060-8327-1  
78-8134-1973-2  
78-8134-1974-0  
78-8060-8323-0  
78-8076-4994-8  
78-8076-5372-6  
78-8076-4532-6  
78-8134-1967-4  
78-8060-8230-7  
78-8060-8231-5  
78-8060-8232-3  
Screw - Hex.Hd, M8x25  
Washer - Triple, M8  
Lockwasher - M8  
Nut - M8  
Sprocket - 3/8", 28 teeth  
Key 6x6x20  
Key 5x5x30  
Bushing  
Flange - Shaft  
Shaft - Drive  
Chain - 3/8", 57 pitch  
Cover - Top  
Screw - Soc.Hd, M5x12  
Support - Bearing, R/H  
Support - Bearing, L/H  
Screw - Soc.Hd, M5x12  
Bracket - Roller, Rear  
Screw - Hex.Hd, M6x12  
Washer - Flat, M6  
Pulley Assy - Drive  
Ring - Pulley  
Nut - Self Locking, M20x1  
Belt - Drive, Laced  
Cover - Drive, Front  
Cover - Drive, Rear  
Spacer  
Screw - Flat Hd, M5x16  
Stud - Side Plate  
Screw - Hex Hd, M5x20  
Screw - Hex Hd, M8x16  
Motor - 110V 60Hz 1Ph, IP56  
Fan - Motor  
Cord Grip ST11  
Stud - Mounting  
Frame - R/H  
Frame - L/H  
Cover - Bottom  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
700a-s Stainless Steel Adjustable Case Sealer  
Figure 10424  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 10424  
Ref. No.  
3M Part No.  
Description  
10424-1  
78-8134-1928-6  
Housing - Wire  
10424-2  
10424-3  
10424-4  
10424-5  
10424-6  
10424-7  
10424-8  
10424-9  
10424-10  
10424-11  
10424-12  
10424-13  
10424-14  
10424-15  
10424-16  
78-8076-4702-5  
78-8060-8332-1  
78-8134-1929-4  
78-8060-8300-8  
78-8060-8303-2  
78-8060-8293-5  
78-8076-4715-7  
78-8134-1975-7  
78-8076-4532-6  
78-8060-8029-3  
78-8134-1931-0  
78-8100-0905-6  
78-8134-1932-8  
78-8076-4645-6  
78-8076-5211-6  
Grommet /28  
Screw - Soc.Hd, M8x16  
Strap - Wire  
Screw - Hex.Hd, M5x10  
Washer - Flat, M5  
Nut - M5  
Cord Grip ST13,5  
Cable - 491P 3 G 1.5, 6 mt  
Cord Grip ST11  
Clamp  
Cover - Housing  
Screw - Hex.Hd, M4x10  
Washer - Triple, M4  
Nut - Lock, GMP11  
Nut - Lock, GMP13,5  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
700a-s Stainless Steel Adjustable Case Sealer  
Figure 10430  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 10430  
Ref. No.  
3M Part No.  
Description  
10430-1  
78-8134-2001-1  
Support - Electric Box  
10430-2  
78-8113-6759-4  
78-8094-6381-9  
78-8060-8297-6  
78-8060-8321-4  
78-8076-4715-7  
78-8076-5211-6  
78-8094-6382-7  
78-8028-8208-0  
78-8017-9018-5  
78-8094-6383-5  
78-8076-5378-3  
78-8094-6384-3  
78-8076-4968-2  
78-8028-7909-4  
78-8100-1038-5  
78-8060-8053-3  
78-8060-8331-3  
78-8060-8312-3  
78-8076-5194-4  
78-8094-6386-8  
78-8134-2002-9  
78-8017-9257-9  
78-8134-2000-3  
78-8060-8293-5  
26-1014-5845-8  
78-8134-2003-7  
78-8134-2004-5  
78-8060-8414-7  
78-8134-2005-2  
78-8114-4896-4  
78-8134-1975-7  
Electric Box  
10430-3  
Screw - Soc.Hd, M4x15  
Washer - Flat, M4  
Nut - Self Locking, M4  
Cord Grip ST13,5  
Nut - Lock GMP 13,5  
Guide - Mounting  
Screw - Self Tapping, 6Px9,5  
Washer - Triple, M4  
Contactor - Allen Bradley 10E  
Switch - Allen Bradley 3-25  
Clamp  
10430-4  
10430-5  
10430-6  
10430-7  
10430-9  
10430-10  
10430-11  
10430-12  
10430-13  
10430-14  
10430-15  
10430-16  
10430-17  
10430-18  
10430-19  
10430-20  
10430-21  
10430-22  
10430-23  
10430-24  
10430-25  
10430-26  
10430-27  
10430-28  
10430-29  
10430-30  
10430-31  
10430-33  
10430-35  
Terminal  
Power Cord  
Cable - 3x20 AWG, 5 mt  
Cable - 3-pole, 5 mt  
Screw - Soc.Hd, M6x16  
Washer - Flat, M6  
Box - E-Stop  
Switch - ON/OFF  
Support - ON/OFF Sswitch  
Screw - Pan Hd, M5x12  
Screw - M5x10  
Nut - M5  
E-Stop W/Latch  
Screw - Hex.hd, M4x20  
Washer - Triple, M4  
Nut - M4  
Collar  
Box - ON/OFF  
Cable - 491P 3G 1.5, 6 mt  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THIS PAGE IS BLANK  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Aastra Telecom Telephone 480i CT User Manual
ADIC Switch Switches User Manual
AEG Ventilation Hood 8259 S User Manual
Allied Telesis Power Supply AT FAN01 User Manual
Allied Telesis Switch AT GS900 16 User Manual
Alto Shaam Food Warmer HN2 72 User Manual
Audiovox Automobile Alarm APS 596 User Manual
Audiovox Automobile Electronics PRO 9232S User Manual
Axor Indoor Furnishings Starck X User Manual
Beko Cooktop CSM 67300 G User Manual