Philips Cordless Telephone D150 User Manual

Register your product and get support at  
D150  
Short user manual  
Overview  
1
In call  
Standby  
Access the main menu.  
Display icons  
It displays the connection between the handset  
Display icons  
Earpiece  
Phonebook  
and the base.The more bars are shown, the  
better the signal strength is.  
Adjust the volume.  
Phonebook  
Call log  
End calls.  
It remains steadily on when browsing incoming  
calls in the call log.  
/
Mute/unmute the microphone.  
Enter a pause.  
Make and receive calls.  
Make intercom call.  
/
It indicates an outgoing call in the redial list.  
Recall (network dependent).  
Lock/unlock the keypad.  
It flashes when there is a new missed call or  
when browsing new missed calls. It remains  
steadily on when browsing the missed calls in  
call log that are already read.  
In menu  
In text input  
Microphone  
Confirm / Enter the option menu. / Select  
Delete text  
Cancel  
It flashes when receiving incoming call. It remains  
Enter a space.  
steadily on during a call.  
Up / down  
The ringer is off.  
Find handset  
Exit menu.  
Voice messages indicator: flashes for new  
messages, is steady for reviewed messages.  
*This is network dependent.  
It displays when you scroll up/down a list or  
increase and decrease the volume.  
There are more digits on the right. Press  
read.  
to  
Connect  
2
1
2
3
Multi-handset version  
only.  
Get started  
3
Insert batteries  
Charge your phone  
Configure your phone  
1 When using your phone for the first time, you see a  
welcome message (country dependent).  
2 Set the country and language if prompted.  
3 Set the date and time.  
Charge 8 hours  
> 70%  
10% - 40%  
< 10%  
If the time is in 12-hour format, press  
/
to  
select [AM] or [PM] (country dependent).  
40% - 70%  
Flashing: low battery  
Scrolling: charging in progress  
Enjoy  
4
Save record  
1 Press  
2 Follow on-screen instructions.  
Phonebook  
Register additional handsets  
>
> [SAVE NUMBER].  
Add record  
You can register additional handsets to the base  
station.  
1 Press  
.
Delete record  
1 Press and hold on the base station for 5 seconds.  
2 Select [PHONEBOOK] > [ADD NEW].  
3 Follow on-screen instructions.  
2 Press  
.
1 Press  
>
> [DELETE].  
3 Select [SERVICES] > [REGISTER], then press  
to confirm.  
4 Enter the system PIN/passcode (0000).  
2 Follow on-screen instructions.  
Call from the phonebook  
1 Press  
.
Redial list  
2 Select a record and press  
.
5 Press  
to confirm the PIN/passcode.  
Call from the redial list  
»
Registration is complete in less than 2 minutes.  
Direct access memory  
1 Press  
.
You have 2 direct access memories (Keys 1 and 2).  
To dial the saved phone number automatically, press  
and hold on the keys in standby mode.  
Depending on your country, keys 1 and 2 are preset  
to [1_VOICEMAIL] (voice mail number) and  
[2_INFO SVC] (information service number)  
of your network operator respectively (network  
dependent).  
2 Select a record and press  
.
Restore default settings  
Save record  
You can reset your phone settings to the original  
factory settings.  
1 Press  
>
> [SAVE NUMBER].  
2 Follow on-screen instructions.  
1 Press  
.
.
2 Select [SERVICES] > [RESET], then press  
to confirm.  
3 Follow on-screen instructions.  
Delete record  
1 Press  
>
> [DELETE].  
2 Follow on-screen instructions.  
Call log  
Note  
Call from the call log  
You may recall the original PIN/passcode by  
following this procedure.  
1 Press  
.
2 Select a record and press  
.
Technical data  
Battery  
Philips: 2 x AAA NiMH 1.2V Rechargeable  
550 mAh batteries  
Use only the supplied batteries.  
Adapter  
Base and charger:  
Philips:  
Input:  
S003IB0600040  
100-240V~  
SSW-1920UK-2  
100-240V~  
50/60 Hz 0.15 A  
Output: 6V 400 mA  
50/60 Hz 0.2 A  
6V 500 mA  
Phonebook with 50 entries  
Call log with 20 entries  
Talk time: 16 hours  
Standby time: 250 hours  
Note  
You can install a DSL (digital subscriber line) filter to  
prevent noise and caller ID problems caused by the  
DSL interference.  
You can find the Declaration of Conformity on  
Frequently asked questions  
No signal bar is displayed on the screen.  
My handset is in searching status, what do I do?  
Bad audio (crackles, echo, etc.)  
The handset is out of range. Move it closer to the  
base station.  
If the handset displays [UNREGISTERED],  
register your handset. (See the section on “Register  
additional handsets”).  
Make sure that the base station has power supply.  
Register the handset to the base station.  
Move the handset closer to the base station.  
The handset is nearly out of range. Move it closer  
to the base station.  
The phone receives interference from the nearby  
electrical appliances. Move the base station away  
from them.  
The phone is at a location with thick walls. Move  
the base away from them.  
I cannot change the settings of my voice mail, what  
do I do?  
The voice mail service is managed by your service  
provider but not the phone itself. Contact your  
service provider to change the settings.  
If I fail to pair (register) the additional handsets to  
the base station, what do I do?  
The handset does not ring.  
Your base memory is full.Access  
>
[SERVICES] > [UNREGISTER] to unregister  
the unused handsets and try again.  
Make sure the handset ringtone is turned on.  
The caller ID does not display.  
The service is not activated. Check with your  
service provider.  
No display  
Make sure the batteries are charged.  
Make sure there are power and phone connections.  
I have chosen a wrong language which I cannot  
read, what do I do?  
The handset on the charger does not charge.  
1 Press  
2 Press  
to go back to the standby screen.  
to access the main menu screen.  
The caller’s information is withheld or unavailable.  
Make sure the batteries are inserted correctly.  
Make sure the handset is placed properly on the  
charger.The battery icon animates when charging.  
Make sure the docking tone setting is turned on.  
When the handset is placed correctly on the  
charger, you can hear a docking tone.  
The charging contacts are dirty. Disconnect the power  
supply first and clean the contacts with a damp cloth.  
Batteries are defective. Purchase new ones with  
the same specifications.  
3 The following options will appear on the screen:  
[PHONE SETUP] > [LANGUAGE]  
[CONFIG.TÉL] > [LANGUE]  
[TEL.-SETUP] > [SPRACHE]  
[CONF.TELEF.] > [LINGUA]  
4 Select it to access the language options.  
5 Select your own language.  
For information, refer to the extended user  
documentation online.  
0168  
When this crossed-out wheeled bin symbol is  
attached to a product it means that the product  
is covered by the European Directive 2002/96/EC.  
2014 © WOOX Innovations Limited.  
All rights reserved.  
Philips and the Philips’ Shield Emblem are  
registered trademarks of Koninklijke Philips N.V.  
and are used by WOOX Innovations Limited  
under license from Koninklijke Philips N.V.  
UMS_D150  
05_EN_V2.0  
WK13501  

KitchenAid Cooktop xgcd807x User Manual
Lenovo ThinkCentre 7360 User Manual
Lucent Technologies Computer Hardware R5SI User Manual
Motorola Cordless Telephone MD451 User Manual
NEC Mitsubishi Diamondtron UWG RDF225WG User Manual
NEC MultiSync FE950+ User Manual
NEC Plasma Monitor User Manual
Philips Business 107MB User Manual
Philips Kala 200 User Manual
Philips MCD755 User Manual