Philips Computer Monitor 223V5 User Manual

223V5

www.philips.com/welcome

EN User manual

Customer care and warranty

Troubleshooting & FAQs

1. Important

‡ꢀ Please use approved power cord provided

by Philips all the time. If your power cord

is missing, please contact with your local

service center. (Please refer to Customer

Care Consumer Information Center)

1. Important

This electronic user’s guide is intended for

anyone who uses the Philips monitor.Take time

to read this user manual before you use your

monitor. It contains important information and

notes regarding operating your monitor.

‡ꢀ Do not subject the monitor to severe

vibration or high impact conditions during

operation.

The Philips guarantee applies provided the

product is handled properly for its intended use,

in accordance with its operating instructions and

upon presentation of the original invoice or cash

receipt, indicating the date of purchase, dealer’s

name and model and production number of the

product.

‡ꢀ Do not knock or drop the monitor during

operation or transportation.

Maintenance

‡ꢀ To protect your monitor from possible

damage, do not put excessive pressure on

the LCD panel. When moving your moni-

tor, grasp the frame to lift; do not lift the

monitor by placing your hand or fingers on

the LCD panel.

1.1 Safety precautions and mainte-

nance

‡ꢀ Unplug the monitor if you are not going to

use it for an extensive period of time.

Warnings

Use of controls, adjustments or procedures

other than those specified in this documentation

may result in exposure to shock, electrical

hazards and/or mechanical hazards.

‡ꢀ Unplug the monitor if you need to clean it

with a slightly damp cloth. The screen may

be wiped with a dry cloth when the power

is off. However, never use organic solvent,

such as, alcohol, or ammonia-based liquids

to clean your monitor.

Read and follow these instructions when

connecting and using your computer monitor.

‡ꢀ To avoid the risk of shock or permanent

damage to the set, do not expose the

monitor to dust, rain, water, or excessive

moisture environment.

Operation

‡ꢀ Please Keep the monitor out of direct

sunlight, very strong bright lights and

away from any other heat source. Lengthy

exposure to this type of environment may

result in discoloration and damage to the

monitor.

‡ꢀ If your monitor gets wet, wipe it with dry

cloth as soon as possible.

‡ꢀ If foreign substance or water gets in your

monitor, please turn the power off immedi-

ately and disconnect the power cord.Then,

remove the foreign substance or water, and

send it to the maintenance center.

‡ꢀ Remove any object that could fall into

ventilation holes or prevent proper cooling

of the monitor’s electronics.

‡ꢀ Do not block the ventilation holes on the

cabinet.

‡ꢀ Do not store or use the monitor in loca-

tions exposed to heat, direct sunlight or

extreme cold.

‡ꢀ When positioning the monitor, make sure

the power plug and outlet are easily ac-

cessible.

‡ꢀ In order to maintain the best performance

of your monitor and use it for a longer life-

time, please use the monitor in a location

that falls within the following temperature

and humidity ranges.

‡ꢀ If turning off the monitor by detaching the

power cable or DC power cord, wait for 6

seconds before attaching the power cable

or DC power cord for normal operation.

1. Important

‡ꢀ Temperature: 0-40°C 32-95°F

what procedure to take when the operating

instructions given in this manual have been

followed.

‡ꢀ Humidity: 20-80% RH

Important information for Burn-in/Ghost

image

1.2 Notational Descriptions

‡ꢀ Always activate a moving screen saver

program when you leave your monitor

unattended. Always activate a periodic

screen refresh application if your monitor

will display unchanging static content.

Uninterrupted display of still or static

images over an extended period may

cause “burn in”, also known as “after-

imaging” or “ghost imaging”, on your

screen.

The following subsections describe notational

conventions used in this document.

Notes, Cautions andWarnings

Throughout this guide, blocks of text may be

accompanied by an icon and printed in bold or

italic type.These blocks contain notes, cautions

or warnings.They are used as follows:

"Burn-in", "after-imaging", or "ghost imag-

ing" is a well-known phenomenon in LCD

panel technology. In most cases, the

“burned in” or “after-imaging” or “ghost

imaging” will disappear gradually over a

period of time after the power has been

switched off.

Note

This icon indicates important information and

tips that help you make better use of your

computer system.

Caution

This icon indicates information that tells you

how to avoid either potential damage to

hardware or loss of data.

Warning

Failure to activate a screen saver, or a periodic

screen refresh application may result in severe”

burn-in” or “after-image” or “ghost image”

symptoms will not disappear and cannot be

repaired.The damage mentioned above is not

covered under your warranty.

Warning

This icon indicates the potential for bodily harm

and tells you how to avoid the problem.

Some warnings may appear in alternate formats

and may not be accompanied by an icon. In such

cases, the specific presentation of the warning is

mandated by the relevant regulatory authority.

Service

‡ꢀ The casing cover should be opened only

by qualified service personnel.

‡ꢀ If there is any need for any document for

repair or integration, please contact with

your local service center. (please refer to

the chapter of "Consumer Information

Center")

‡ꢀ For transportation information, please

refer to "Technical Specifications".

‡ꢀ Do not leave your monitor in a car/trunk

under direct sun light.

Note

Consult a service technician if the monitor

does not operate normally, or you are not sure

1. Important

Taking back/Recycling Information for

Customers

1.3 Disposal of product and packing

material

Philips establishes technically and economically

viable objectives to optimize the environmental

performance of the organization's product,

service and activities.

Waste Electrical and Electronic Equipment-

WEEE

From the planning, design and production

stages, Philips emphasizes the important of

making products that can easily be recycled. At

Philips, end-of-life management primarily entails

participation in national take-back initiatives

and recycling programs whenever possible,

preferably in cooperation with competitors,

which recycle all materials (products and related

packaging material) in accordance with all

Environmental Laws and taking back program

with the contractor company.

This marking on the product or on its

packaging illustrates that, under European

Directive 2002/96/EC governing used electrical

and electronic appliances, this product may

not be disposed of with normal household

waste.You are responsible for disposal of

this equipment through a designated waste

electrical and electronic equipment collection.

To determine the locations for dropping off

such waste electrical and electronic, contact

your local government office, the waste disposal

organization that serves your household or the

store at which you purchased the product.

Your display is manufactured with high quality

materials and components which can be

recycled and reused.

To learn more about our recycling program

please visit

Your new monitor contains materials that can

be recycled and reused. Specialized companies

can recycle your product to increase the

amount of reusable materials and to minimize

the amount to be disposed of.

http://www.philips.com/sites/philipsglobal/

about/sustainability/ourenvironment/

productrecyclingservices.page

All redundant packing material has been

omitted.We have done our utmost to make the

packaging easily separable into mono materials.

Please find out about the local regulations on

how to dispose of your old monitor and packing

from your sales representative.

2. Setting up the monitor

Install base stand

2. Setting up the monitor

1. Place the monitor face down on soft

and smooth surface taking care to avoid

scratching or damaging the screen.

2.1 Installation

2. Attach/Slide the base column with the

monitor until it clicks into position.

Package contents

223V5

www.philips.com/welcome

Quick

Start

使用产品

前请阅

读使用说

明

3. Hold the monitor base stand with both

hands and firmly insert the base stand into

the base column.

SmartControl software

Monitor drivers

保留备用

Power cable

Audio cable (optional)

DVI (optional)

VGA (optional)

2. Setting up the monitor

Connecting to your PC

2.2 Operating the monitor

223V5LSB/223V5LSB2

Front view product description

AC power input

VGA input

DVI-D input (available for selected models)

Kensington anti-theft lock

223V5L

223V5LHSB

Switch monitor’s power ON and

OFF.

Access the OSD menu

Confirm the OSD adjustment.

Return to previous OSD level.

Adjust the brightness level.

Adjust the OSD menu.

AC power input

VGA input

HDMI input

HDMI Audio out

Kensington anti-theft lock

Connect to PC

Change display format.

1. Connect the power cord to the back of

the monitor firmly.

Automatically adjust the monitor.

2. Turn off your computer and unplug its

power cable.

3. Connect the monitor signal cable to the

video connector on the back of your

computer.

4. Plug the power cord of your computer and

your monitor into a nearby outlet.

5. Turn on your computer and monitor. If the

monitor displays an image, installation is

complete.

2. Setting up the monitor

Description of the On Screen Display

The OSD Menu

Below is an overall view of the structure of

the On-Screen Display.You can use this as a

reference when you want to work your way

around the different adjustments later on.

What is On-Screen Display (OSD)?

On-Screen Display (OSD) is a feature in all

Philips LCD monitors. It allows an end user to

adjust screen performance or select functions

of the monitors directly through an on-screen

instruction window.A user friendly on screen

display interface is shown as below:

Main menu

Sub menu

VGA

DVI (available for selective models)

HDMI (available for selective models)

Input

223V5LHSB:

Wide Screen, 4:3

Picture Format

Brightness

9*$

,QSXW

+'0,

0~100

Picture

Contrast

0~100

3LFWXUH

$XGLR

SmartContrast

On, Off

Over scan

(available for selective models)

On, Off

&RORU

Volume

Mute

0~100

Audio

On, Off

/DQJXDJH

(available for selective models)

6500K, 9300K

Color Temperature

sRGB

Color

223V5LSB/223V5LSB2:

Red: 0~100

Green: 0~100

Blue: 0~100

User Define

9*$

,QSXW

'9,

3LFWXUH

Language

English,Español,Français,Deutsch,Italiano,

Português,Русский,৿࿒፩ၭĭTürkçe,

&RORU

Nederlands, Svenska, Suomi, Polski, Čeština

䚐ạ㛨, ஬ঐ൩, Maryar, Українська,

Português do Brazil,Ελληνική (προαιρετικός),

體ሱ༵ꢀস選ꢀ

/DQJXDJH

26'ꢀ6HWWLQJV

0~100

Horizontal

Vertical

0~100

223V5LSB/223V5LSB2 (for 1A model):

OSD Settings

Off, 1, 2, 3, 4

5s, 10s, 20s, 30s, 60s

Transparency

3LFWXUHꢀꢀ)RUPDWꢀꢀ

%ULJKWQHVVꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ

&RQWUDVW

:LGHꢀ6FUHHQ

3LFWXUH

OSD Time Out

ꢁꢂꢂ

ꢃꢂ

&RORU

Auto

6PDUW&RQWUDVW

2II

Setup

0~100

H. Position

V. Position

Phase

/DQJXDJH

26'ꢀ6HWWLQJV

6HWXS

Clock

Resolution Notification

Reset

On, Off

Yes, No

Information

Basic and simple instruction on the control

keys

In the OSD shown above, you can press

buttons at the front bezel of the monitor

to move the cursor, and press OK button to

confirm the choice or change.

2. Setting up the monitor

Resolution notification

2.3 Remove Base Stand and Base

This monitor is designed for optimal

performance at its native resolution, 1920 ×

1080 @ 60 Hz.When the monitor is powered

on at a different resolution, an alert is displayed

on screen: Use 1920 × 1080 @ 60 Hz for best

results.

Remove the Base Stand

Before you start disassembling the monitor

base, please follow the instructions below to

avoid any possible damage or injury.

1. Place the monitor face down on a smooth

surface, taking care to avoid scratching or

damaging the screen.

Display of the native resolution alert can be

switched off from Setup in the OSD (On

Screen Display) menu.

Physical Function

Tilt

2. Press the locking clips to detach the base

stand away from the base column.

3. Press the release button to detach the base

column.

2. Setting up the monitor

Note

This monitor accepts a 100mm x 100mmVESA-

Compliant mounting interface.

100mm

Caution

For use only with UL Listed Wall Mount Bracket

with minimum weight/load 3.5Kg

3. Image Optimization

Icon based software is ready to enhance your

experience with Philips monitors!

3. Image Optimization

Installation

3.1 SmartContrast

vꢀ Follow the instruction and complete the

installation.

What is it?

vꢀ You can launch after installation is

completed.

A unique technology that dynamically analyzes

displayed content and automatically optimizes

an LCD monitor's contrast ratio for maximum

visual clarity and viewing enjoyment, stepping

up backlighting for clearer, crisper and brighter

images or dimming backlighting for clear display

of images on dark backgrounds.

vꢀ If you want to launch later, you can either

click the shortcut on desktop or toolbar.

Why do I need it?

You want the very best visual clarity and

viewing comfort for every type of content.

SmartContrast dynamically controls contrast

and adjusts backlighting for clear, crisp, bright

gaming and video images or displays clear,

readable text for office work. By reducing your

monitor's power consumption, you save on

energy costs and extend the lifetime of your

monitor.

First launch -Wizard

How does it work?

vꢀ The first time after installation of

SmartControl Lite, it will automatically go

to Wizard for first time launch.

When you activate SmartContrast, it will analyse

the content you are displaying in real time to

adjust colors and control backlight intensity.This

function will dynamically enhance contrast for a

great entertainment experience when viewing

videos or playing games.

vꢀ The wizard will guide you through adjusting

your monitor performance step by step.

vꢀ You can go to Plug-in menu to launch

wizard later on as well.

vꢀ You can adjust more options without

wizard by Standard pane.

3.2 Philips SmartControl Lite

The new SmartControl Lite software by Phillips

allows you to control your monitor via an easy

to use on-screen graphic interface. Complicated

adjustments are a thing of the past as this user

friendly software guides you through fine-

tuning resolution, Color calibration, Clock/Phase

adjustments, RGB White point adjustment, etc.

Equipped with latest technology in core

algorithm for fast processing and response, this

Windows 7 compliant eye catching animated

3. Image Optimization

Start with Standard pane:

Adjust menu:

vꢀ Adjust Menu allow you to adjust Brightness,

Contrast, Focus, Position and Resolution.

vꢀ You can follow the instruction and do the

adjustment.

vꢀ Cancel prompts user if you want to cancel

installation.

3. Image Optimization

Color menu:

vꢀ Color Menu allow you to adjust RGB, Black

Level,White Point, and Color Calibration.

vꢀ You can follow the instruction and do the

adjustment.

vꢀ Refer to below table for sub-menu item

base on your input.

vꢀ Example for Color Calibration:

3. Image Optimization

1. "Show Me" starts color calibration tutorial.

Options>Preferences - Will only be active

when selecting Preferences from the drop-

down Options menu. On a non-supported

display capable of DDC/CI, only the Help and

Options tabs are available.

2. Start - starts the 6-step color calibration

sequence.

3. Quick View loads the before/after images.

4. To return to Color home pane, click the

Cancel button.

5. Enable color calibration - by default is on.

If unchecked, does not allow for color

calibration to happen, dimes out start and

quick view buttons.

6. Must have patent info in calibration screen.

First color Calibration Screen:

vꢀ Displays current preference settings.

vꢀ A checked box enables the feature.The

check box is a toggle.

vꢀ Previous button is disabled until the second

color screen.

vꢀ Enable Context Menu on desktop is

checked (On) by default. Enable Context

menu displays SmartControl Lite selections

for Select Preset andTune Display in the

desktop right-click context menu. Disabled

removes SmartControl Lite from the right

click context menu.

vꢀ Next goes to the succeeding target

(6-targets).

vꢀ Final next goes File>Presets pane.

vꢀ Cancel closes the UI and returns to the

plug in page.

vꢀ EnableTaskTray icon is checked (On) by

default. Enable context menu shows the

task tray menu for SmartControl Lite. A

right click on the task tray icon displays the

menu options for Help,Technical Support,

Check for Upgrade, About, and Exit.When

Enable task tray menu is disabled, the task

tray icon will only display EXIT.

vꢀ Run at Startup is checked (On) by default.

When disabled, SmartControl Lite will not

launch at start or be in the task tray.The

only way to launch SmartControl Lite is

either from the desktop short cut or from

the program file. Any preset set to run

3. Image Optimization

at startup will not load when this box is

unchecked (Disabled).

vꢀ Enable transparency mode (Windows 7,

Vista, XP). Default is 0% Opaque.

Options>Input - Will only be active when

selecting Input from the drop-down Options

menu. On a non-supported display capable of

DDC/CI, only the Help and Options tabs are

available.All other SmartControl Lite tabs are

not available.

Help>User Manual - Will only be active when

selecting User Manual from the drop-down

Help menu. On a non-supported display

capable of DDC/CI, only the Help and Options

tabs are available.

vꢀ Display the Source instruction pane and

current input source setting.

vꢀ On single input displays, this pane will not

be visible.

Options>Audio - Will only be active when

selecting Audio from the drop-down Options

menu.

On a non-supported display capable of DDC/

CI, only the Help and Options tabs are available.

Help>Version - Will only be active when

selectingVersion from the drop- down Help

menu. On a non-supported display capable of

DDC/CI, only the Help and Options tabs are

available.

3. Image Optimization

The task tray has five entries:

vꢀ Help - Access to User Manual file: Open

User Manual file using the default browser

window.

vꢀ Technical Support - displays the tech

support page.

Context Sensitive menu

vꢀ Check for Update - takes the user to PDI

Landing and checks the user’s version

against the most current available.

The Context Sensitive menu is Enabled by

default. If Enable Context Menu has been

checked in the Options>Preferences pane, then

the menu will be visible.

vꢀ About - Displays detailed reference

information: product version, release

information, and product name.

vꢀ Exit - Close SmartControl Lite.

To run SmartControl Lite again either select

SmartControl Lite from Program menu, double-

click the desktop PC icon or restart the system.

The Context Menu has three entries:

vꢀ SmartControl Lite - When selected the

About Screen is displayed.

vꢀ Select Preset - Provides a hierarchical

menu of saved presets for immediate use.

A check mark shows the currently selected

preset. Factory Preset can also be called

from the drop down menu.

vꢀ Tune Display - Opens the SmartControl

Lite control panel.

TaskTray Menu Disabled

When theTaskTray is disabled in the preference

folder, only the EXIT selection is available.

To completely remove SmartControl Lite

from the task tray, disable Run at Startup in

Options>Preferences.

TaskTray Menu Enabled

The task tray menu can be displayed by right-

clicking on the SmartControl Lite icon from the

task tray. Left Click will launch the application.

3. Image Optimization

Note

All the illustrations in this section are for

reference only. SmartControl software version

might be changed without notification. Please

always check official Portrait website

www.portrait.com/dtune/phl/enu/index

to download the latest version of SmartControl

software.

ꢀꢁꢂ7HFKQLFDOꢂ6SHFLÀFDWLRQV

4. Technical Specifications

Picture/Display

Monitor PanelType

Backlight

TFT-LCD

LED

Panel Size

21.5" W (54.6cm)

Aspect Ratio

16:9

Pixel Pitch

0.248 x 0.248 mm

250 cd/m² or 200 cd/m²

10,000,000:1

Brightness

SmartContrast

Contrast Ratio (typ.)

ResponseTime (typ.)

Optimum Resolution

1000:1 or 600:1 for 200 nits

5ms

1920 x 1080 @ 60Hz

170° (H) / 160° (V) @ C/R > 10

or 90° (H) / 65° (V) @ C/R > 10 for 200 nits

16.7M

Viewing Angle

Display Colors

Vertical Refresh Rate

Horizontal Frequency

sRGB

56Hz - 76Hz

30kHz - 83kHz

YES

Connectivity

223V5LSB/223V5LSB2:VGA(Analog) ,DVI(Digital,HDCP)

(optional)

Signal Input

223V5LHSB:VGA(Analog), HDMI(Digital,HDCP)

HDMI audio out ( 223V5LHSB)

Audio In/Out

Input Signal

Separate Sync, Sync on Green

Convenience

User Convenience

English, French, German, Spanish, Italian, Russian,

Simplified Chinese, Portuguese,Turkish, Dutch, Swedish, Finnish,

Polish, Czech, Korean, Japanese, Hungarian, Ukraine, Brazil

Portuguese, Greek(optional),Traditional Chinese(optional)

Kensington Lock

OSD Languages

Other Convenience

DDC/CI, sRGB,Windows 7/Windows 8/Vista/XP, Mac OSX,

Linux

Plug & Play Compatibility

VESA mount

Stand

100x100 mm

Tilt

-5 / +20

223V5LHSB:

Power

On Mode

19.66 W (typ.), 23.76 W (max.)

Sleep (Standby)

Off

0.5W

Power LED indicator

On mode:White, Standby/Sleep mode:White (blinking)

ꢀꢁꢂ7HFKQLFDOꢂ6SHFLÀFDWLRQV

Power Supply

Built-in, 100-240VAC, 50-60Hz

223V5LSB/223V5LSB2:

Power

18.6 W (typ.), 22.57 W (max.)for 223V5LSB

or 17.07 W (typ.), 20.26W (max.) for 223V5LSB

On Mode

Sleep (Standby)

Off

0.5W

Power LED indicator

Power Supply

On mode:White, Standby/Sleep mode:White (blinking)

Built-in, 100-240VAC, 50-60Hz

Dimension

Product with stand (WxHxD)

Product without stand

(WxHxD)

503 x 376 x 213 mm

503 x 316 x 50 mm

Weight

Product with stand

Product without stand

Product with packaging

2.605kg

2.304kg

3.866kg

Operating Condition

Temperature range (operation)

Temperature range

0°C to 40 °C

-20°C to 60°C

(Non-operation)

Relative humidity

20% to 80%

30,000hrs

MTBF

Environmental

ROHS

YES

EPEAT

Silver (www.epeat.net)

100% recyclable

YES

Packaging

Energy Star

Compliance and standards

CE Mark, FCC Class B, EAC, SEMKO, BSMI, cETLus,

ISO9241-307,TCO Certified(Only for selective models)

Regulatory Approvals

Cabinet

Color

Black

Finish

Texture

Note

1. EPEAT Gold or Silver is valid only where Philips registers the product. Please visit www.epeat.net

for registration status in your country.

2. This data is subject to change without notice. Go to www.philips.com/support to download the

latest version of leaflet.

ꢀꢁꢂ7HFKQLFDOꢂ6SHFLÀFDWLRQV

4.1 Resolution & Preset Modes

Maximum Resolution

1920 x 1080 @ 60 Hz (analog input)

1920 x 1080 @ 60 Hz (digital input)

Recommended Resolution

1920 x 1080 @ 60 Hz (digital input)

H. freq (kHz) Resolution

V. freq (Hz)

31.47

35.00

37.86

37.50

37.88

46.88

48.36

60.02

44.77

63.89

79.98

55.94

70.64

65.29

67.50

720 x 400

640 x 480

70.09

59.94

66.67

72.81

75.00

60.32

75.00

60.00

75.03

59.86

60.02

75.03

59.89

74.98

59.95

60.00

640 x 480

800 x 600

1024 x 768

1280 x 720

1280 x 1024

1440 x 900

1680 x 1050

1920 x 1080

Note

Please notice that your display works best at

native resolution of 1920 x 1080 @ 60Hz. For

best display quality,please follow this resolution

recommendation.

5. Power Management

If you haveVESA DPM compliance display card

or software installed in your PC, the monitor

can automatically reduce its power consumption

when not in use. If an input from a keyboard,

mouse or other input device is detected,

the monitor will 'wake up' automatically.The

following table shows the power consumption

and signaling of this automatic power saving

feature:

223V5LHSB:

Power Management Definition

VESA

Mode

Video H-sync V-sync

Power Used

19.66 W (typ.)

0.5W (typ.)

LED Color

White

Active

OFF

Yes

Sleep

(Standby)

White

(blink)

Switch Off OFF

0.5W (typ.)

OFF

223V5LSB/223V5LSB2:

Power Management Definition

VESA

Mode

Video H-sync V-sync

Power Used

LED Color

White

18.6 W (typ.) for

223V5LSB

Active

OFF

Yes

or 17.07 W (typ.)

for 223V5LSB2

Sleep

(Standby)

White

(blink)

0.5W (typ.)

Switch Off OFF

OFF

The following setup is used to measure power

consumption on this monitor.

vꢀ Native resolution: 1920 x 1080

vꢀ Contrast: 50%

vꢀ Brightness: 250 nits or 200 nits

vꢀ Color temperature: 6500k with full white

pattern

Note

This data is subject to change without notice.

6. Regulatory Infomation

vꢀ Design for Recycling

Coding of plastics for easy recycling. Limit

on the number of different plastics used.

6. Regulatory Information

Lead-free Product

vꢀ Product Lifetime, ProductTake Back

Minimum one-year product warranty.

Minimum three-year availability of spare

parts. Product takeback

Lead free display promotes

environmentally sound recovery

and disposal of waste from electrical

and electronic equipment.Toxic

vꢀ Packaging

substances like Lead has been eliminated

and compliance with European community’s

stringent RoHs directive mandating restrictions

on hazardous substances in electrical and

electronic equipment have been adhered to

in order to make Philips monitors safe to use

throughout its life cycle.

Limits on hazardous substances in product

packaging. Packaging prepared for recycling

vꢀ Ergonomic, User-centered design

Visual ergonomics in products with a

display. Adjustability for user comfort

(displays, headsets) Acoustic performance

– protection against sound spikes

(headsets) and fan noise (projectors,

computers) Ergonomically designed

keyboard (notebooks)

Congratulations!

This product isTCO Certified - for Sustainable

vꢀ Electrical Safety, minimal electro-magnetic

Emissions Third PartyTesting

TCO Certified is an international

third party sustainability certification

for IT products.TCO Certified.

All certified product models have been

tested in an independent, accredited

laboratory.

ensures that the manufacture, use and recycling

of IT products reflect environmental, social and

economic responsibility. EveryTCO Certified

product model is verified by an accredited

independent test laboratory.

A detailed criteria set is available for download

at www.tcodevelopment.com, where you can

also find a searchable database of allTCO

Certified IT products.

This product has been verified to meet all the

criteria inTCO Certified, including:

TCO Development, the organization behind

TCO Certified, has been an international

driver in the field of Sustainable IT for 20 years.

Criteria inTCO Certified are developed in

collaboration with scientists, experts, users

and manufacturers. Organizations around

the world rely onTCO Certified as a tool to

help them reach their sustainable IT goals.We

are owned byTCO, a non-profit organization

representing office workers.TCO Development

is headquartered in Stockholm, Sweden, with

regional presence in North America and Asia.

vꢀ Corporate Social Responsibility

Socially responsible production - working

conditions and labor law in manufacturing

country

vꢀ Energy Efficiency

Energy efficiency of product and power

supply. Energy Star compliant, where

applicable

vꢀ Environmental Management System

Manufacturer must be certified according

to either ISO 14001 or EMAS

For more information, please visit

www.tcodevelopment.com

vꢀ Minimization of Hazardous Substances

Limits on cadmium, mercury, lead

& hexavalent chromium including

requirements for mercury-free products,

halogenated substances and hazardous

flame retardants

Technology for you and the planet

(Only for selective models)

6. Regulatory Infomation

EPEAT

CE Declaration of Conformity

(www.epeat.net)

This product is in conformity with the following

standards

The EPEAT (Electronic

vꢀ EN60950-1:2006+A11:2009+A1:20

10+A12:2011 (Safety requirement of

InformationTechnology Equipment).

Product Environmental

AssessmentTool) program

evaluates computer

desktops, laptops, and monitors based on 51

environmental criteria developed through

an extensive stakeholder consensus process

supported by US EPA.

vꢀ EN55022:2010 (Radio Disturbance

requirement of InformationTechnology

Equipment).

vꢀ EN55024:2010 (Immunity requirement of

InformationTechnology Equipment).

EPEAT system helps purchasers in the public

and private sectors evaluate, compare and

select desktop computers, notebooks and

monitors based on their environmental

attributes. EPEAT also provides a clear and

consistent set of performance criteria for the

design of products, and provides an opportunity

for manufacturers to secure market recognition

for efforts to reduce the environmental impact

of its products.

vꢀ EN61000-3-2:2006 +A1:2009+A2:2009

(Limits for Harmonic Current Emission).

vꢀ EN61000-3-3:2008 (Limitation of Voltage

Fluctuation and Flicker) following provisions

of directives applicable.

vꢀ 2006/95/EC (LowVoltage Directive).

vꢀ 2004/108/EC (EMC Directive).

vꢀ 2009/125/EC (ErP Directive, EC No.

1275/2008 Implementing Directive

for Standby and Off mode power

consumption) and is produced by a

manufacturing organization on ISO9000

level.

Benefits of EPEAT

Reduce use of primary materials

Reduce use of toxic materials

Avoid the disposal of hazardous waste EPEAT’S

requirement that all registered products meet

ENERGY STAR’s energy efficiency specifications,

means that these products will consume less

energy throughout their life.

The product also comply with the following

standards

vꢀ ISO9241-307:2008 (Ergonomic

requirement, Analysis and compliance test

methods for electronic visual displays).

vꢀ GS EK1-2000:2011 (GS mark requirement).

vꢀ prEN50279:1998 (Low Frequency Electric

and Magnetic fields forVisual Display).

vꢀ MPR-II (MPR:1990:8/1990:10 Low

Frequency Electric and Magnetic fields).

vꢀ TCO CERTIFIED (Requirement for

Environment Labeling of Ergonomics,

Energy, Ecology and Emission,TCO: Swedish

Confederation of Professional Employees)

forTCO versions.

6. Regulatory Infomation

Energy Star Declaration

(www.energystar.gov)

Changes or modifications not expressly

approved by the party responsible for

compliance could void the user's authority

to operate the equipment.

As an ENERGY STAR^®Partner, we

have determined that this product

meets the ENERGY STAR^®

guidelines for energy efficiency.

Use only RF shielded cable that was supplied

with the monitor when connecting this monitor

to a computer device.

Note

We recommend you switch off the monitor

when it is not in use for a long time.

To prevent damage which may result in fire or

shock hazard, do not expose this appliance to

rain or excessive moisture.

THIS CLASS B DIGITAL APPARATUS MEETS

ALL REQUIREMENTS OFTHE CANADIAN

INTERFERENCE-CAUSING EQUIPMENT

REGULATIONS.

Federal Communications Commission (FCC)

Notice (U.S. Only)

This equipment has been tested and found

to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC

Rules.These limits are designed to provide

reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference

to radio communications.

FCC Declaration of Conformity

Declaration of Conformity for Products Marked

with FCC Logo,

United States Only

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any

interference received, including interference that

may cause undesired operation.

However, there is no guarantee that

interference will not occur in a particular

installation. If this equipment does cause

harmful interference to radio or television

reception, which can be determined by

turning the equipment off and on, the

user is encouraged to try to correct

the interference by one or more of the

following measures:

Commission Federale de la Communication

(FCC Declaration)

Cet équipement a été testé et déclaré

conforme auxlimites des appareils

numériques de class B,aux termes de

l'article 15 Des règles de la FCC. Ces

limites sont conçues de façon à fourir

une protection raisonnable contre les

interférences nuisibles dans le cadre d'une

installation résidentielle.

vꢀ Reorient or relocate the receiving antenna.

vꢀ Increase the separation between the

equipment and receiver.

vꢀ Connect the equipment into an outlet on

a circuit different from that to which the

receiver is connected.

vꢀ Consult the dealer or an experienced

radio/TV technician for help.

CET appareil produit, utilise et peut émettre

des hyperfréquences qui, si l'appareil n'est

pas installé et utilisé selon les consignes

données, peuvent causer des interférences

nuisibles aux communications radio.

6. Regulatory Infomation

Cependant, rien ne peut garantir l'absence

d'interférences dans le cadre d'une

installation particulière. Si cet appareil est

la cause d'interférences nuisibles pour

la réception des signaux de radio ou de

télévision, ce qui peut être décelé en

fermant l'équipement, puis en le remettant

en fonction, l'utilisateur pourrait essayer de

corriger la situation en prenant les mesures

suivantes:

EN 55022 Compliance (Czech Republic Only)

Polish Center forTesting and Certification

Notice

The equipment should draw power from a

socket with an attached protection circuit (a

three-prong socket).All equipment that works

together (computer, monitor, printer, and so on)

should have the same power supply source.

vꢀ Réorienter ou déplacer l’antenne de

réception.

vꢀ Augmenter la distance entre l’équipement

et le récepteur.

vꢀ Brancher l’équipement sur un autre circuit

que celui utilisé par le récepteur.

The phasing conductor of the room's electrical

installation should have a reserve short-circuit

protection device in the form of a fuse with a

nominal value no larger than 16 amperes (A).

vꢀ Demander l’aide du marchand ou d’un

technicien chevronné en radio/télévision.

Toutes modifications n'ayant pas reçu

l'approbation des services compétents

en matière de conformité est susceptible

d'interdire à l'utilisateur l'usage du présent

équipement.

To completely switch off the equipment, the

power supply cable must be removed from the

power supply socket, which should be located

near the equipment and easily accessible.

A protection mark "B" confirms that the

equipment is in compliance with the protection

usage requirements of standards PN-93/T-42107

and PN-89/E-06251.

N'utiliser que des câbles RF armés pour

les connections avec des ordinateurs ou

périphériques.

CET APPAREIL NUMERIQUE DE LA CLASSE

B RESPECTETOUTES LES EXIGENCES DU

REGLEMENT SUR LE MATERIEL BROUILLEUR

DU CANADA.

6. Regulatory Infomation

North Europe (Nordic Countries) Information

Ergonomie Hinweis (nur Deutschland)

Der von uns gelieferte Farbmonitor entspricht

den in der "Verordnung über den Schutz vor

Schäden durch Röntgenstrahlen" festgelegten

Vorschriften.

Placering/Ventilation

VARNING:

FÖRSÄKRA DIG OM ATT HUVUDBRYTARE

OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR

DU STÄLLER DIN UTRUSTNING PÅPLATS.

Auf der Rückwand des Gerätes befindet sich

ein Aufkleber, der auf die Unbedenklichkeit der

Inbetriebnahme hinweist, da dieVorschriften

über die Bauart von Störstrahlern nach Anlage

,,,ꢀiꢀꢁꢀ$EVꢂꢀꢃꢀGHUꢀ5ÜQWJHQYHURUGQXQJꢀHUIâOOWꢀVLQGꢂꢀ

Placering/Ventilation

ADVARSEL:

SØRG VED PLACERINGEN FOR, AT

NETLEDNINGENS STIK OG STIKKONTAKT

ER NEMTTILGÆNGELIGE.

Damit Ihr Monitor immer den in der Zulassung

geforderten Werten entspricht, ist darauf zu

achten, daß

Paikka/Ilmankierto

VAROITUS:

1. Reparaturen nur durch Fachpersonal

durchgeführt werden.

SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO

VOIDAAN TARVITTAESSA HELPOSTI

IRROTTAA PISTORASIASTA.

2. nur original-Ersatzteile verwendet werden.

3. bei Ersatz der Bildröhre nur eine

bauartgleiche eingebaut wird.

Plassering/Ventilasjon

ADVARSEL:

Aus ergonomischen Gründen wird empfohlen,

die Grundfarben Blau und Rot nicht auf

dunklem Untergrund zu verwenden (schlechte

Lesbarkeit und erhöhte Augenbelastung bei zu

geringem Zeichenkontrast wären die Folge).

Der arbeitsplatzbezogene Schalldruckpegel

nach DIN 45 635 beträgt 70dB (A) oder

weniger.

NÅR DETTE UTSTYRET PLASSERES, MÅ

DU PASSE PÅ AT KONTAKTENE FOR

STØMTILFØRSEL ER LETTE Å NÅ.

BSMI Notice (Taiwan Only)

ACHTUNG: BEIM AUFSTELLEN

DIESES GERÄTES DARAUF

ACHTEN, DAß NETZSTECKER UND

NETZKABELANSCHLUß LEICHT

ZUGÄNGLICH SIND.

6. Regulatory Infomation

China RoHS

EU Energy Label

The People's Republic of China released a

regulation called "Management Methods for

Controlling Pollution by Electronic Information

Products" or commonly referred to as China

RoHS.All products including CRT and Monitor

which are produced and sold for China market

have to meet China RoHS request.

The European Energy Label informs you on

the energy efficiency class of this product.

The greener the energy efficiency class of this

product is the lower the energy it consumes.

On the label, you can find the energy efficiency

class, the average power consumption of

this product in use and the average energy

consumption for 1 year.

㩾অ

شࠌ

ཚૻ

䰬兘ਐཚૻʻԼ

ʼʿ䶣՗ॾஒ䣈঴խܶ

ऱ

੅

୭ढ

凝

ࢨ

ցై

إڇ

ൄ

شࠌ

ऱ㦕ٙՀլ㢸䦡

؆इ

ࢨ

ડ䦣ʿʳ䶣

՗ॾஒ䣈঴

㡬

شࠌ

具䶣՗ॾஒ䣈঴լ㢸㢑㩾ቼທ

䢘

ૹ

਩

ࢨ

㢑ࠡԳ

Εʳ凗䣈ທ

䢘ૹ䮦୭ऱཚૻΗ

Note

The EU Energy Label will be ONLY applied on

the models bundling with HDMI andTV tuners.

И֢ਈ

ࣤݼ࢛

߶જ

݇И֢

ஏ澦ਈ

ࣤݼ࢛

߶જ঒

ࣲ

ࡣ

澧ͫ

ުॐ֘অՠљЈ੽

ࡌ

ਈ

ࣤݼ࢛

ꢃIJꢀ=ꢂ

$ꢄꢇꢁꢅꢆ

Ҽ୻

ہࣙ

ਈ৴ͧ=ꢂ "ꢄꢅꢁꢆ

ਈ

ঈ঴

ਈ

߶ӕ

ꢇ঴

-(ꢄꢈꢇꢆꢈꢅꢉꢈꢅꢅꢊ

દূ

ҼҒ

બ߲ஃИ֢ਈ

߶જৠ͹NZZV ꢀꢀ]]]ꢁKTKXM_RGHKRꢁMU\ꢁITꢀ

π䬙㥯䶣ᕴ䶣՗䣈঴

گڃ

㢊෻ጥ෻㦕

ࠏ

ρ༼

ࢤق

円

ࣔ

䢠Ա

چړޓ

䤤䵋֗অ䮍

෺Δ㣞

㡬լ٦Ꮑ૞

䣈঴

ࢨ

䣈঴㥣

ࡎ

伡ַ㦍Δ冉ᙅ

㧺୮䬙㥯䶣ᕴ䶣՗䣈঴

گڃ

㢊

෻ઌ䤤ऄ৳ऄ億Δ㰒ٌࠡ伲㣞

ࠠ

㧺୮儶

ऱ

گڃ

㢊

෻凹凝ऱᩈ೸劓۩

گڃ

㢊෻Ζʳʳ

7. Customer care and warranty

black pixel. Other combinations of lit and dark

sub pixels appear as single pixels of other colors.

7. Customer care and

warranty

Types of Pixel Defects

Pixel and sub pixel defects appear on the screen

in different ways.There are two categories of

pixel defects and several types of sub pixel

defects within each category.

7.1 Philips’ Flat Panel Monitors Pixel

Defect Policy

Philips strives to deliver the highest quality

products.We use some of the industry's most

advanced manufacturing processes and practice

stringent quality control. However, pixel or

sub pixel defects on theTFT Monitor panels

used in flat panel monitors are sometimes

unavoidable. No manufacturer can guarantee

that all panels will be free from pixel defects,

but Philips guarantees that any monitor with an

unacceptable number of defects will be repaired

or replaced under warranty.This notice explains

the different types of pixel defects and defines

acceptable defect levels for each type. In order

to qualify for repair or replacement under

warranty, the number of pixel defects on aTFT

Monitor panel must exceed these acceptable

levels. For example, no more than 0.0004% of

the sub pixels on a monitor may be defective.

Furthermore, Philips sets even higher quality

standards for certain types or combinations

of pixel defects that are more noticeable than

others.This policy is valid worldwide.

Bright Dot Defects

Bright dot defects appear as pixels or sub pixels

that are always lit or 'on'.That is, a bright dot is

a sub-pixel that stands out on the screen when

the monitor displays a dark pattern.There are

the types of bright dot defects.

One lit red, green or blue sub pixel.

Two adjacent lit sub pixels:

Red + Blue = Purple

Red + Green =Yellow

Green + Blue = Cyan (Light Blue)

Pixels and Sub pixels

A pixel, or picture element, is composed of

three sub pixels in the primary colors of red,

green and blue. Many pixels together form an

image.When all sub pixels of a pixel are lit, the

three colored sub pixels together appear as a

single white pixel.When all are dark, the three

colored sub pixels together appear as a single

Three adjacent lit sub pixels (one white pixel).

7. Customer care and warranty

Proximity of Pixel Defects

Note

A red or blue bright dot must be more

Because pixel and sub pixels defects of the

same type that are near to one another may be

more noticeable, Philips also specifies tolerances

for the proximity of pixel defects.

than 50

percent brighter than neighboring dots while

a green bright dot is 30 percent brighter than

neighboring dots.

Black Dot Defects

Black dot defects appear as pixels or sub pixels

that are always dark or 'off'.That is, a dark dot is

a sub-pixel that stands out on the screen when

the monitor displays a light pattern.These are

the types of black dot defects.

Pixel DefectTolerances

In order to qualify for repair or replacement

due to pixel defects during the warranty period,

aTFT Monitor panel in a Philips flat panel

monitor must have pixel or sub pixel defects

exceeding the tolerances listed in the following

tables.

BRIGHT DOT DEFECTS

ACCEPTABLE LEVEL

1 lit subpixel

2 adjacent lit subpixels

3 adjacent lit subpixels (one white pixel)

Distance between two bright dot defects*

Total bright dot defects of all types

>15mm

BLACK DOT DEFECTS

ACCEPTABLE LEVEL

5 or fewer

2 or fewer

1 dark subpixel

2 adjacent dark subpixels

3 adjacent dark subpixels

Distance between two black dot defects*

Total black dot defects of all types

>15mm

5 or fewer

TOTAL DOT DEFECTS

ACCEPTABLE LEVEL

Total bright or black dot defects of all types

5 or fewer

Note

1. 1 or 2 adjacent sub pixel defects = 1 dot defect

2. This monitor is ISO9241-307 compliant, Class-I compliant.(ISO9241-307: Ergonomic requirement ,

analysis and compliance test methods for electronic visual displays)

3. ISO9241-307 is the successor of formerly known ISO13406 standard, which is withdrawn by the

International Organisation for Standardisation (ISO) per: 2008-11-13.

7. Customer care and warranty

7.2 Customer Care &Warranty

For warranty coverage information and additional support requirement valid for your region, please visit

www.philips.com/support website for details. You may also contact your local Philips Customer Care

Center number listed below.

Contact Information forWESTERN EUROPE region:

Country

Austria

CSP

Hotline Number

+43 0810 000206

+32 078 250851

800 92 256

Price

Opening Hours

RTS

0.07

0.06

Mon to Fri : 9am - 6pm

Mon to Fri : 8am - 5pm

Mon to Fri : 9am - 6pm

Mon to Fri : 8am - 5pm

Mon to Fri : 9am - 6pm

Mon to Fri : 8am - 5pm

€

Belgium

Cyprus

Ecare

Alman

Infocare

Mainteq

RTS

Free of charge

Local call tariff

Denmark

Finland

+45 3525 8761

+358 09 2290 1908 Local call tariff

France

+33 082161 1658

0.09

€

Germany

Greece

Ireland

+49 01803 386 853

Alman

Celestica

Anovo Italy

Ecare

+30 00800 3122 1223 Free of charge

+353 01 601 1161

+39 840 320 041

+352 26 84 30 00

+31 0900 0400 063

+47 2270 8250

Local call tariff

0.08

Italy

€

Luxembourg

Netherlands

Norway

Poland

Local call tariff

0.10

Ecare

€

Infocare

MSI

Local call tariff

Free of charge

+48 0223491505

800 780 902

Portugal

Spain

Mainteq

Infocare

+34 902 888 785

+46 08 632 0016

0.10

€

Sweden

Switzerland

Local call tariff

ANOVO CH +41 02 2310 2116

United Kingdom Celestica

+44 0207 949 0069

Contact Information for China:

Country

Call center

Consumer care number

China

PCCW Limited

4008 800 008

Contact Information for NORTH AMERICA :

Country

U.S.A.

Call center

EPI-e-center

Consumer care number

(877) 835-1838

Canada

(800)479-6696

7. Customer care and warranty

Contact Information for CENTRAL AND EASTERN EUROPE region:

Country

Call center

CSP

Consumer care number

+375 17 217 3386

+375 17 217 3389

Belarus

IBA

Bulgaria

LAN Service

MR Service Ltd

Asupport

+359 2 960 2360

+385 (01) 640 1111

420 272 188 300

Croatia

Czech Rep.

+372 6519900(General)

+372 6519972(workshop)

Estonia

FUJITSU

Esabi

Georgia

+995 322 91 34 71

+36 1 814 8080(General)

+36 1814 8565(For AOC&Philips

only)

Hungary

Profi Service

Kazakhstan

Latvia

Classic Service I.I.c.

ServiceNet LV

+7 727 3097515

+371 67460399

+371 27260399

+370 37 400160(general)

+370 7400088 (for Philips)

Lithuania

UAB Servicenet

Macedonia

Moldova

AMC

+389 2 3125097

+37322224035

Comel

Romania

Skin

+40 21 2101969

+7 (495) 645 6746

+381 11 20 70 684

+421 2 49207155

+386 1 530 08 24

+ 375 17 284 0203

+90 212 444 4 832

+38044 525 64 95

+380 5627444225

Russia

CPS

Serbia&Montenegro

Slovakia

KimTec d.o.o.

Datalan Service

PC H.and

ServiceBy

Tecpro

Slovenia

the republic of Belarus NA

Turkey

Ukraine

Topaz

Comel

Contact Information for LATIN AMERICA region:

Country

Brazil

Call center

Consumer care number

0800-7254101

Vermont

Argentina

0800 3330 856

7. Customer care and warranty

Contact Information for APMEA region:

Country

ASP

Consumer care number

1300 360 386

Opening hours

Australia

AGOS NETWORK PTY LTD

Mon.~Fri. 9:00am-5:30pm

Mon.~Fri. 8:30am-5:30pm

New Zealand Visual Group Ltd.

0800 657447

Hong Kong:

Tel: +852 2619 9639

Macau:Tel: (853)-0800-987

Hong Kong

Macau

Company: Smart Pixels

Technology Ltd.

Mon.~Fri. 9:00am-6:00pm

Sat. 9:00am-1:00pm

Tel: 1 800 425 6396

SMS: PHILIPS to 56677

India

REDINGTON INDIA LTD

Mon.~Fri. 9:00am-5:30pm

+62-21-4080-9086 (Customer

Hotline)

Mon.~Thu. 08:30-12:00;

13:00-17:30

Fri. 08:30-11:30; 13:00-17:30

PT. CORMIC SERVISINDO

PERKASA

Indonesia

Korea

+62-8888-01-9086 (Customer

Hotline)

Mon.~Fri. 9:00am-5:30pm

Sat. 9:00am-1:00pm

Alphascan Displays, Inc

R-Logic Sdn Bhd

1661-5003

Mon.~Fri. 8:15am-5:00pm

Sat. 8:30am-12:30am

Malaysia

Pakistan

+603 5102 3336

+92-213-6030100

TVONICS Pakistan

Sun.~Thu. 10:00am-6:00pm

Philips Electronics Singapore

Pte Ltd (Philips Consumer Care (65) 6882 3966

Center)

Mon.~Fri. 9:00am-6:00pm

Sat. 9:00am-1:00pm

Singapore

Taiwan

FETEC.CO

0800-231-099

Mon.~Fri. 09:00 - 18:00

Axis Computer System Co.,

Ltd.

Thailand

(662) 934-5498

Mon.~Fri. 8:30am~05:30pm

South Africa Computer RepairTechnologies 011 262 3586

Mon.~Fri. 8:00am~05:00pm

Sun.~Thu. 08:00-18:00

Israel

Eastronics LTD

1-800-567000

+84 8 38248007 Ho Chi Minh

City

FPT Service Informatic

Company Ltd. - Ho Chi Minh

City Branch

Mon.~Fri. 8:00-12:00, 13:30-

17:30,Sat. 8:00-12:00

Vietnam

+84 5113.562666 Danang City

+84 5113.562666 Can tho

Province

EA Global Supply Chain

Solutions ,Inc.

Philippines

(02) 655-7777; 6359456

Mon.~Fri. 8:30am~5:30pm

Sun.~Thu. 09:00 - 18:00

Armenia

Azerbaijan

Georgia

Firebird service centre

+97 14 8837911

Kyrgyzstan

Tajikistan

Soniko Plus Private Enterprise

Ltd

Uzbekistan

+99871 2784650

Mon.~Fri. 09:00 - 18:00

Turkmenistan Technostar Service Centre

+(99312) 460733, 460957

03-5676-6022

ࡈ

ࠖ

ࡊ࡝

ࠬ

ࡐࠨ࡮࡯࠲࠾ࡕ

ꢀ

࡯

࡯࠲ࡦ࠮࠻

Japan

8.Troubleshooting & FAQs

satisfactory, you can do manual adjustments

via the OSD menu.

8. Troubleshooting & FAQs

Note

The Auto Function is not applicable in DVI-

Digital mode as it is not necessary.

8.1 Troubleshooting

This page deals with problems that can be

corrected by a user. If the problem still persists

after you have tried these solutions, contact

Philips customer service representative.

Visible signs of smoke or sparks

vꢀ Do not perform any troubleshooting steps

vꢀ Disconnect the monitor from mains power

source immediately for safety

Common Problems

vꢀ Contact with Philips customer service

representative immediately.

No Picture (Power LED not lit)

vꢀ Make sure the power cord is plugged into

the power outlet and into the back of the

monitor.

Imaging Problems

Image is not centered

vꢀ First, ensure that the power button on the

front of the monitor is in the OFF position,

then press it to the ON position.

vꢀ Adjust the image position using the “Auto”

function in OSD Main Controls.

vꢀ Adjust the image position using the Phase/

Clock of Setup in OSD Main Controls. It is

valid only in VGA mode.

No Picture (Power LED isWhite)

vꢀ Make sure the computer is turned on.

vꢀ Make sure the signal cable is properly

connected to your computer.

Image vibrates on the screen

vꢀ Check that the signal cable is properly

securely connected to the graphics board

or PC.

vꢀ Make sure the monitor cable has no bent

pins on the connect side. If yes, repair or

replace the cable.

Vertical flicker appears

vꢀ The Energy Saving feature may be activated

Screen says

Attention

vꢀ Adjust the image using the “Auto” function

in OSD Main Controls.

Check cable connection

vꢀ Eliminate the vertical bars using the Phase/

Clock of Setup in OSD Main Controls. It is

valid only in VGA mode.

vꢀ Make sure the monitor cable is properly

connected to your computer. (Also refer to

the Quick Start Guide).

Horizontal flicker appears

vꢀ Check to see if the monitor cable has bent

pins.

vꢀ Make sure the computer is turned on.

AUTO button doesn't function

vꢀ Adjust the image using the “Auto” function

in OSD Main Controls.

vꢀ The auto function is applicable only in

VGA-Analog mode. If the result is not

8.Troubleshooting & FAQs

vꢀ Eliminate the vertical bars using the Phase/

Clock of Setup in OSD Main Controls. It is

valid only in VGA mode.

For further assistance, refer to the Consumer

Information Centers list and contact Philips

customer service representative.

Image appears blurred, indistinct or too dark

vꢀ Adjust the contrast and brightness on

On-Screen Display.

8.2 General FAQs

Q1: When I install my monitor what should

I do if the screen shows 'Cannot display

this video mode'?

An "after-image", "burn-in" or "ghost image"

remains after the power has been turned off.

vꢀ Uninterrupted display of still or static

images over an extended period may cause

"burn in", also known as "after-imaging "

or "ghost imaging", on your screen. "Burn-

in", "after-imaging", or "ghost imaging" is a

well-known phenomenon in LCD panel

technology. In most cases, the "burned in"

or "after-imaging" or "ghost imaging" will

disappear gradually over a period of time

after the power has been switched off.

Ans.: Recommended resolution for this

monitor: 1920 x 1080 @ 60 Hz.

vꢀ Unplug all cables, then connect your PC to

the monitor that you used previously.

vꢀ In the Windows Start Menu, select Settings/

Control Panel. In the Control Panel

Window, select the Display icon. Inside the

Display Control Panel, select the 'Settings'

tab. Under the setting tab, in box labelled

'desktop area', move the sidebar to 1920 x

1080 pixels.

vꢀ Always activate a moving screen saver

program when you leave your monitor

unattended.

vꢀ Open 'Advanced Properties' and set the

Refresh Rate to 60 Hz, then click OK.

vꢀ Always activate a periodic screen refresh

application if your LCD monitor will display

unchanging static content.

vꢀ Restart your computer and repeat step 2

and 3 to verify that your PC is set at 1920

x 1080 @ 60 Hz.

vꢀ Severe” burn-in” or “after-image” or “ghost

image” symptoms will not disappear and

cannot be repaired.The damage mentioned

above is not covered under your warranty.

vꢀ Shut down your computer, disconnect your

old monitor and reconnect your Philips

LCD monitor.

vꢀ Turn on your monitor and then turn on

your PC.

Image appears distorted.Text is fuzzy or

blurred.

Q2: What is the recommended refresh rate

for LCD monitor?

vꢀ Set the PC’s display resolution to the same

mode as monitor’s recommended screen

native resolution.

Ans.: Recommended refresh rate in LCD

monitors is 60 Hz, In case of any

disturbance on screen, you can set it

up to 75 Hz to see if that removes the

disturbance.

Green, red, blue, dark, and white dots appears

on the screen

vꢀ The remaining dots are normal

characteristic of the liquid crystal used in

today’s technology, Please refer the pixel

policy for more detail.

Q3: What are the .inf and .icm files on the

CD-ROM? How do I install the drivers

(.inf and .icm)?

Ans.: These are the driver files for your

monitor. Follow the instructions in your

user manual to install the drivers.Your

computer may ask you for monitor

The "power on" light is too strong and is

disturbing

vꢀ You can adjust “power on” light using the

power LED Setup in OSD main Controls.

8.Troubleshooting & FAQs

drivers (.inf and .icm files) or a driver disk

when you first install your monitor. Follow

the instructions to insert the ( companion

CD-ROM) included in this package.

Monitor drivers (.inf and .icm files) will be

installed automatically.

"warm, with a red-white color tone",

while a 9300K temperature yields "cool,

bluewhite toning".

2. sRGB; this is a standard setting for

ensuring correct exchange of colors

between different device (e.g. digital

cameras, monitors, printers, scanners,

etc)

Q4: How do I adjust the resolution?

Ans.: Your video card/graphic driver and

monitor together determine the available

resolutions.You can select the desired

resolution under Windows^®Control

Panel with the "Display properties".

3. User Define; the user can choose his/

her preference color setting by adjusting

red, green blue color.

Note

Q5: What if I get lost when I am making

monitor adjustments via OSD?

Ans.: Simply press the OK button, then select

'Reset' to recall all of the original factory

settings.

A measurement of the color of light radiated

by an object while it is being heated.This

measurement is expressed in terms of

absolute scale, (degrees Kelvin). Lower Kevin

temperatures such as 2004K are red; higher

temperatures such as 9300K are blue. Neutral

temperature is white, at 6504K.

Q6: Is the LCD screen resistant to scratches?

Ans.: In general it is recommended that the

panel surface is not subjected to excessive

shocks and is protected from sharp or

blunt objects.When handling the monitor,

make sure that there is no pressure or

force applied to the panel surface side.

This may affect your warranty conditions.

Q9: Can I connect my LCD monitor to any

PC, workstation or Mac?

Ans.: Yes.All Philips LCD monitors are fully

compatible with standard PCs, Macs

and workstations.You may need a cable

adapter to connect the monitor to your

Mac system. Please contact your Philips

sales representative for more information.

Q7: How should I clean the LCD surface?

Ans.: For normal cleaning, use a clean, soft

cloth. For extensive cleaning, please use

isopropyl alcohol. Do not use other

solvents such as ethyl alcohol, ethanol,

acetone, hexane, etc.

Q10: Are Philips LCD monitors Plug-and-

Play?

Ans.: Yes, the monitors are Plug-and-Play

compatible with Windows 7/Windows 8/

Vista/XP/NT, Mac OSX, Linux

Q8: Can I change the color setting of my

monitor?

Ans.: Yes, you can change your color setting

through OSD control as the following

procedures,

Q11: What is Image Sticking, or Image Burn-in,

or After Image, or Ghost Image in LCD

panels?

Ans.: Uninterrupted display of still or static

images over an extended period may

cause "burn in", also known as "after-

imaging" or "ghost imaging", on your

screen. "Burn-in", "after-imaging", or "ghost

imaging" is a well-known phenomenon in

LCD panel technology. In most cases, the

"burned in" or "atter-imaging" or "ghost

vꢀ Press "OK" to show the OSD (On Screen

Display) menu

vꢀ Press "Down Arrow" to select the option

"Color" then press "OK" to enter color

setting, there are three settings as below.

1. ColorTemperature;The two settings

are 6500K and 9300K.With settings

in the 6500K range the panel appears

8.Troubleshooting & FAQs

imaging" will disappear gradually over a

period of time after the power has been

switched off.

Always activate a moving screen saver

program when you leave your monitor

unattended.

Always activate a periodic screen refresh

application if your LCD monitor will

display unchanging static content.

Warning

Failure to activate a screen saver, or a periodic

screen refresh application may result in severe

“burn-in” or “after-image” or “ghost image”

symptoms that will not disappear and cannot

be repaired.The damage mentioned above is

not covered under your warranty.

Q12: Why is my Display not showing sharp

text, and is displaying jagged characters?

Ans.: Your LCD monitor works best at its native

resolution of 1920 x 1080 @ 60 Hz. For

best display, please use this resolution.

Philips and the Philips Shield Emblem are registered trademarks of

Koninklijke Philips Electronics N.V. and are used under license from

Koninklijke Philips Electronics N.V.

Specifications are subject to change without notice.

Version: M5223V1T

ICP DAS USA PCI P16C16 User Manual
Jenn Air EXPRESSIONS W30400S User Manual
JVC AV 21QT5BU User Manual
LG Electronics W2600H User Manual
Lincoln 1132 08H A User Manual
Motorola Cordless Telephone MD451 User Manual
NEC MultiSync LCD1550M User Manual
Palsonic 5125PF User Manual
Perreaux TU3 User Manual
Philips 1 92E+04 User Manual