Philips 32PT9005D User Manual

27PT9015D  
32PT7005D  
32PT9005D  
User Manual  
Thank you for choosing Philips.  
Need help fast?  
Read your Quick Use Guide and/or  
Owner's Manual first for quick tips  
that make using your Philips product  
more enjoyable.  
If you have read your instructions  
and still need assistance,  
you may access our online help at  
or call  
1-888-PHILIPS (744-5477)  
while with your product  
(and Model / Serial number)  
For Customer Use  
Enter below the Serial No. which is located  
on the rear of the cabinet. Retain this  
information for future reference.  
Model No. __________________________  
Serial No. __________________________  
IMPORTANT SAFETY INSTRUCTIONS  
Read before operating equipment  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Do not use this TV near water.  
6. Clean only with a dry cloth.  
D. The TV does not appear to operate normally or exhibits a  
marked change in performance; or  
E. The TV has been dropped, or the enclosure damaged.  
17. Tilt/Stability - All televisions must comply with recommended  
international global safety standards for tilt and stability properties  
of its cabinet design.  
• Do not compromise these design standards by applying excessive  
pull force to the front, or top, of the cabinet which could ultimately  
overturn the product.  
7. Do not block any of the ventilation openings. Install in accordance  
with the manufacturers instructions.  
• Also, do not endanger yourself, or children, by placing electronic  
equipment/toys on the top of the cabinet. Such items could  
unsuspectingly fall from the top of the set and cause product  
damage and/or personal injury.  
8. Do not install near any heat sources such as radiators, heat  
registers, stoves, or other apparatus (including amplifiers) that  
produce heat.  
9. Do not defeat the safety purpose of the polarized or grounding-  
type plug. A polarized plug has two blades with one wider than the  
other. A grounding type plug has two blades and third grounding  
prong. The wide blade or third prong are provided for your safety.  
When the provided plug does not fit into your outlet, consult an  
electrician for replacement of the obsolete outlet.  
18. Wall or Ceiling Mounting - The TV should be mounted to a  
wall or ceiling only as recommended by the manufacturer.  
19. Power Lines - An outdoor antenna should be located away from  
power lines.  
20. Outdoor Antenna Grounding - If an outside antenna is  
connected to the receiver, be sure the antenna system is grounded so  
as to provide some protection against voltage surges and built up static  
charges.  
10. Protect the power cord from being walked on or pinched  
particularly at plugs, convenience receptacles, and the point where  
they exit from the apparatus.  
Section 810 of the National Electric Code, ANSI/NFPA No. 70-  
1984, provides information with respect to proper grounding of  
the mast and supporting structure, grounding of the lead-in wire to  
an antenna discharge unit, size of grounding connectors, location  
of antenna-discharge unit, connection to grounding electrodes, and  
requirements for the grounding electrode. See Figure below.  
11. Only use attachments/accessories specified by the manufacturer.  
12.  
Use only with a cart, stand, tripod, bracket, or table  
specified by the manufacturer, or sold with the TV  
When a cart is used, use caution when moving  
the cart/TV combination to avoid injury from tip-over.  
13. Unplug this TV during lightning storms or when unused for long  
21. Object and Liquid Entry - Care should be taken so that  
objects do not fall and liquids are not spilled into the enclosure  
through openings.  
periods of time.  
14. Refer all servicing to qualified service personnel. Servicing is  
required when the TV has been damaged in any way, such as  
power-supply cord or plug is damaged, liquid has been spilled or  
objects have fallen into apparatus, the TV has been exposed to rain  
or moisture, does not operate normally, or has been dropped.  
15. This product may contain lead and mercury. Disposal of these  
materials may be regulated due to environmental considerations.  
For disposal or recycling information, please contact your local  
a) Warning: To reduce the risk of fire or electric shock, this  
apparatus should not be exposed to rain or moisture and objects  
filled with liquids, such as vases, should not be placed on this  
apparatus.  
22. Battery Usage CAUTION - To prevent battery leakage that  
may result in bodily injury, property damage, or damage to the unit:  
• Install all batteries correctly, with + and - aligned as marked on  
the unit.  
• Do not mix batteries (old and new or carbon and alkaline, etc.).  
• Remove batteries when the unit is not used for a long time.  
16. Damage Requiring Service - The TV should be serviced by qualified  
service personnel when:  
A. The power supply cord or the plug has been damaged; or  
B. Objects have fallen, or liquid has been spilled into the TV; or  
C. The TV has been exposed to rain; or  
Note to the CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC  
that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the  
building, as close to the point of cable entry as practical.  
Example of Antenna Grounding  
as per NEC - National Electric Code  
3
FEATURES  
CONTENTS  
INTRODUCTION  
Active Control continuously measures and corrects all incoming  
signals to help provide the best picture quality. This feature  
monitors and corrects both the sharpness control and noise  
reduction control (Pg. 17).  
Welcome/Registration of Your TV . . . . . . . . . . . . . . . . . . . . . .2  
Safety/Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2/3  
A Guide to Digital TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
Quick Tips Before You Start . . . . . . . . . . . . . . . . . . . . . . . . . .5  
Audio Volume Leveler (AVL) Control keeps the TV sound at  
an even level. Differences in volume levels during commercial breaks  
are reduced, making for a more consistent, comfortable sound for  
your listening pleasure (Pg. 19).  
GETTING STARTED  
Description of Remote Control buttons. . . . . . . . . . . . . . . . . .6  
Basic TV and Remote Control Operation . . . . . . . . . . . . . . . .7  
First Time You Turn On The TV . . . . . . . . . . . . . . . . . . . . . . .8  
AutoChron sets the clock of the TV automatically or manually. For  
automatic selection, there will be queries for Time Zone, Day Light  
saving and channel to seek clock. For manual selection, you need to  
key in the time. (Pg. 13).  
INSTALLATION MENU  
Auto Install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
How To Use The Language Controls . . . . . . . . . . . . . . . . . . .10  
How To Use The Tuner Mode Control . . . . . . . . . . . . . . . . .11  
Channel Edit (Add or skip channels) . . . . . . . . . . . . . . . . . . .12  
AutoLock lets you block channels or programs from viewing with  
content not suitable for children or with restricted TV ratings (Pg.  
21).  
Digital  
Auto Chron (Synchronisation of time) . . . . . . . . . . .13  
Timer - Time Zone . . . . . . . . . . . . . . . . . . . . . . . . . .14  
Timer - Daylight Saving. . . . . . . . . . . . . . . . . . . . . . . .14  
How To Add Or Skip Weak Digital Signals . . . . . . .15  
Emergency Alert Setting . . . . . . . . . . . . . . . . . . . . . .16  
Factory Channel Reset . . . . . . . . . . . . . . . . . . . . . . .16  
Digital Audio (Selecting audio languages) . . . . . . . . .17  
Digital  
AutoPicture lets you change the picture settings (color, tint,  
contrast, etc.) for various types of programming, such as sports,  
movies, multimedia (games), or weak signals with the push of one  
button (Pg. 18).  
Digital  
l
Digita  
Digital  
l
Digita  
AutoSound lets you select from four pre-set controls and a  
personal control that you set according to your own preferences  
through the onscreen Sound menu. The four pre-set controls  
(Speech, Movie, Music, and Multimedia) lets you custom set the TV  
sound to enhance the particular programming you are watching (Pg.  
19).  
Digita  
l
Picture Menu Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18  
Sound Menu Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19  
FEATURES MENU  
Understanding Autolock Controls. . . . . . . . . . . . . . . . . . . . . .20  
AutoLock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21  
AutoLock - Blocking Channels . . . . . . . . . . . . . . . . . . . . . . . .22  
Block / Clear All Channels At The Same Time. . . . . . . . . . . .23  
Blocking Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23  
Movie Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24  
TV Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25  
How To Use the Timer Menu Controls. . . . . . . . . . . . . . . . .26  
Close Captioning Display in Digital Mode. . . . . . . . .27  
Channel Edit lets you add or skip channels from the list stored in  
the TV memory. Channel Edit makes it easy to limit or expand the  
number of channels that are available to you when you press the  
Channel (+) or (–) buttons on your remote control (Pg. 12).  
Closed Captioning allows the viewer to read TV program  
dialogue or voice conversations as onscreen text. (Pg. 27-28).  
Digital Audio allows you to switch to another audio language  
when it is available. This is only for programs that are shown in  
more than one audio language (Page 17).  
Digita  
l
Caption Option in Digital Mode . . . . . . . . . . . . . . . .27  
Digita  
l
Close Captioning in Analog Mode. . . . . . . . . . . . . . . . . . . . . .28  
SleepTimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29  
Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29  
How To Use The Format Control . . . . . . . . . . . . . . . . . . . . .30  
Sleep Timer automatically turns OFF the TV after a set amount of  
time that you have chosen ( Page 29).  
OTHER FEATURES  
As an Energy Star® Partner, Philips Consumer  
Electronics has determined this product meets  
Active Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17  
Auto Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18  
Auto Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19  
Information Banner and Electronic Program Guide .31  
the Energy Star® guidelines for energy efficiency  
Energy Star® is a U.S. registered mark. Using  
products with the Energy Star® label can save energy. Saving  
energy reduces air pollution and lowers utility bills.  
Digita  
l
Active Control, AutoPicture, AutoSound, AutoChron, and  
Incredible Surround are trademarks of Philips Consumer  
Electronics Company. Copyright 2001 Philips Consumer  
Electronics.  
IMPORTANT INFORMATION  
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32  
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33-34  
Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35  
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36  
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37  
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38  
*Manufactured under license from Dolby  
Laboratories. “Dolby” and the double-D symbol  
are trademarks of Dolby Laboratories.  
4
A GUIDE TO DIGITAL TV  
What is Digital Television (DTV)?  
Digital Television (DTV) is a relatively new type of broadcasting that promises to transform television viewing into a whole  
new experience. Digital technology is used to capture images and sound to deliver a better picture quality.  
There are many levels of digital television quality. The most common are:  
Standard Definition TV (SDTV)  
SDTV is the basic level of quality display and resolution for both analog and digital. Transmission of SDTV can be in the  
traditional (4:3) or widescreen (16:9) format.  
Enhanced Definition TV (EDTV)  
EDTV is better in picture quality than analog television. The formats for EDTV are 480p widescreen (16:9) or traditional (4:3).  
EDTV is in the middle range quality between SDTV and HDTV.  
High Definition TV (HDTV)  
HDTV has the highest quality for digital broadcast formats. Its resolution is widescreen format (16:9). Combined with digitally  
enhanced sound technology, HDTV sets new standards for sound and picture quality in television.  
Difference between Digital and Analog ?  
Digital Television is a more flexible and efficient technology than the analog broadcast system. Analog broadcasts can only  
provide one program at a time. Digital television can broadcast a high definition program or more than one standard definition  
program at the same time. With Digital television you can receive information of programs through the Information Banner  
and Electronic Program Guide. This information is provided by the broadcaster.  
QUICK TIPS BEFORE YOU START  
1
2
3
When the TV is powered-on for the first time you will be prompted to auto install the TV in order to receive the channels  
that are broadcasted locally.  
Auto Installation may take 20 to 40 minutes depending on the number of channels that are transmitted by the cable provider  
or broadcaster.  
When the TV is not receiving any signal from the antenna / cable, NO SIGNAL will appear on the TV screen. This can be  
caused by the antenna / cable not being plugged in correctly or when the wrong tuner mode is selected.  
When no transmission is received from the broadcaster, NO PROGRAM will appear on the TV screen.  
4
5
You will not be able to receive pay channels when using direct antenna / cable connection to the television.  
When the Set-top box is connected to the television using coaxial cable, it is necessary to auto-program the television for the  
single channel (3 or 4) that the Set-top box outputs and change the channels at the Set-top Box to view the program.  
6
7
When the Set-top box is connected to the television using AV connection, select the television input source for the  
Set-top box to view the program and change the channels at the Set-top Box to view the program.  
Pressing the A/D button on the remote control toggles the TV between Digital and Analog Mode.  
Accessories List :  
1 Remote Control  
2 AA batteries  
1 User Manual  
1 Warranty Card  
5
DESCRIPTION OF REMOTE CONTROL BUTTONS  
CLOCK Button - Sets the TV  
clock On or Off.  
SLEEP Button - Sets the TV to  
automatically turn itself off after  
a period of time you choose  
FORMAT Button - To select  
picture format.  
POWER Button - Press to turn the  
TV On or put on Standby mode.  
AV Button - To select different signal  
sources connected to the AV inputs on  
the TV(eg. DVD, VCR, Camcorder etc.)  
POWER  
* Guide Button - Displays the  
Electronic Program guide (only in  
Digital Mode)  
SAP Button - Toggle between SAP,  
Mono and Stereo Sound.  
FORMAT CLOCK SLEEP GUIDE  
AUTO SOUND Button - To  
select factory-defined sound settings.  
(Personal, Theatre, Music, or Voice).  
CC Button - Closed Captioning.  
* INFO Button - To display channel  
number, sound mode, time and status of  
the sleeptimer, etc.  
AV  
SAP  
CC  
INFO  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
A/D (ANALOG/DIGITAL)  
Button - To select Analog or  
Digital mode.  
AUTO PICTURE Button - To choose  
from five pre-defined picture settings.  
(Personal, Movies, Sports, Weak Signal,  
or Multimedia).  
MENU  
OK  
MENU Button - To display the main  
menu.  
OK Button - To activate selection of  
antenna / cable mode the first time you  
auto install the TV.  
Cursor Buttons (< , >, <, > )  
- To highlight and select items on  
the TV onscreen menu.  
MUTE  
VOL  
CH  
CH(annel) + or CH(annel)- Buttons  
- To select channels in ascending or  
descending order.  
VOL(ume) + / - Buttons  
- To increase or decrease the  
TV sound level.  
1
2
5
8
0
3
MUTE Button - To turn off  
the sound from the TV.  
4
6
NUMERIC (0-9) Buttons - To select  
TV channels or enter values in the on-  
screen menu. For single channel entries,  
press the numbered button for the chan-  
nel you desire. The TV will pause for a  
second or two before changing to the  
chosen channel.  
7
9
A/CH  
A/CH (Alternate Channel)  
Button - Toggle between last  
viewed and current channel.  
DOT Button - To enter values for minor  
channels eg. 36.4  
HELPFUL HINTS  
* The quality and accuracy of the information on the program guide and information banner are transmitted from broadcasters.  
You may see a difference in broadcast time if the broadcaster is from a different time zone area (refer to page 31).  
The INFO button can also be used to exit the menu display from the TV screen.  
6
BASIC TV AND REMOTE CONTROL OPERATION  
32PT9005D  
Press POWER button on the TV to turn it  
on. Pressing any button on the front panel  
of the TV will also turn the TV On.  
1
2
Press the VOLUME + to increase the  
sound level and VOLUME – to lower the  
sound level.  
Pressing both buttons together will display  
the onscreen menu. While in menu mode,  
use these buttons to make adjustments or  
selections.  
3
Press CHANNEL + or to select TV  
channels.  
3
4
5
Point the remote control towards the  
remote sensor window on the front of the  
TV when using the remote control.  
27PT9015D  
32PT7005D  
Press MENU button on the remote to  
display the onscreen menu.  
-
+
>
<
3
REMOTE CONTROL  
ow to load the supplied batteries into the remote  
Hcontrol.  
Back of Remote  
Remove the battery compartment lid on the  
back of the remote control.  
1
Battery Compartment  
Insert two AA-sized batteries into the battery  
compartment, making sure the positive + and  
negative - polarity line up correctly as indicated  
inside the case.  
2
2 AA-sized batteries  
Close the battery lid.  
Battery compartment lid  
3
7
FIRST TIME YOU TURN ON THE TV  
he first time you turn on the new TV set, you will see a screen that helps you to auto install the programs. Follow  
Tthe instructions on this screen to start auto installation. Digital and Analog auto installation will be performed  
at the same time. Auto installation may take 20 to 40 minutes depending on the number of channels available. You  
will see the progress of the auto installation represented by the 2 bars below the words Analog Channels and Digital  
Channels respectively. An active hour-glass will be displayed on the TV screen to indicate that auto installation is still  
in progress, please wait.  
Note : This screen will only appear the first time you turn on the TV. If you wish to auto install programs  
later, please follow the procedure in the next page (page 9).  
POWER  
FORMAT CLOCK SLEEP GUIDE  
Please connect Antenna or Cable to TV  
AV  
SAP  
CC  
INFO  
Select TV signal by Î or ï and press OK  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
Æ
Antenna  
Cable  
MENU  
OK  
OK  
< >  
Installation may take about 30 mintues.  
MUTE  
VOL  
CH  
1
2
5
8
0
3
4
6
Auto Install  
Analog channels  
39  
45  
7
9
A/CH  
Digital Channels  
HELPFUL HINTS  
ANTENNA : If you have and off-air or roof-top  
antenna, select Antenna.  
CABLE : If you have subscribed to cable signal from  
any cable company, or you are receiving free-to-air cable  
channels through your wall connection select Cable.  
When you install in either Digital or Analog mode,  
both Digital and Analog channels will be installed.  
8
AUTO INSTALL  
ou can auto install programs on your TV. This makes it easy for you to select only the TV stations in your area  
Ywhen the CHANNEL (+), (–) buttons are pressed.  
Digital Mode  
Analog Mode  
Follow these steps for Digital Mode and Analog Mode  
Complete the antenna or cable signal connection  
before activating AUTO INSTALL. See How to  
make the best connection guide for details.  
Language  
Language  
Tuner Mode  
Auto Install  
Tuner Mode  
Auto Install  
Channel Edit  
1
Press MENU button on the remote control to  
display the onscreen menu.  
DTV Setup  
2
Press CURSOR < or > to scroll through the  
onscreen menu until you see Install highlighted.  
3
Install  
Language  
Tuner Mode  
Auto Install  
Channel Edit  
Install  
Language  
Tuner Mode  
Auto Install  
Press CURSOR > to display the Install menu  
features.  
4
Press CURSOR < or > to scroll through the  
Install features until you see Auto Install highlighted.  
5
Press CURSOR > to start Auto Installation.  
6
Auto Install will begin. This may take 20 to 40  
minutes depending on the number  
of channels available.  
Auto Install  
Analog channels  
Auto Install  
39  
45  
Analog channels  
39  
45  
7
Digital Channels  
Digital Channels  
When finished, press MENU button on the remote  
control twice to exit the menu display from  
8
the TV screen.  
POWER  
FORMAT CLOCK SLEEP GUIDE  
AV  
SAP  
CC  
INFO  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
A/D  
MENU  
OK  
MENU  
toggles between  
digital and analog  
mode  
< >  
MUTE  
VOL  
CH  
1
2
5
8
0
3
HELPFUL HINTS  
When CABLE is selected, channels 1 to 135 are available  
in Digital Mode and Channels 1 to 125 are available in  
Analog Mode.  
4
6
7
9
A/CH  
When ANTENNA is selected, channels 2 to 69 are  
available for both Digital and Analog Modes.  
When you are in Digital Mode, channel numbers will be  
displayed as 23-1, or 100-2 etc.  
When you install in either Digital or Analog mode,  
both Digital and Analog channels will be installed.  
9
HOW TO USE THE LANGUAGE CONTROL  
or French and Spanish speaking TV owners an onscreen Language option is present. With the Language control you  
Fcan set the TV’s on-screen menu to be shown in English, French, or Spanish.  
Analog Mode  
Digital Mode  
Follow these steps for Digital Mode and Analog Mode  
Press MENU button on the remote control to display  
the onscreen menu.  
Main  
Language  
Tuner Mode  
Auto Install  
Language  
1
Tuner Mode  
Auto Install  
Channel Edit  
Press CURSOR < or > to scroll through the  
onscreen menu until you see Install highlighted.  
DTV Setup  
2
Press CURSOR > to display the Install menu  
features.  
3
Press CURSOR < or > to scroll through the  
Install features until you see Language highlighted.  
Install  
Language  
Tuner Mode  
Auto Install  
Install  
Language  
Tuner Mode  
Auto Install  
Channel Edit  
4
Press CURSOR > to select English, Français  
(French) or Español (Spanish).  
5
When finished, press MENU button on the remote  
twice to exit the menu from the TV screen.  
6
Press A/D button on the remote to switch between  
Digital and Analog Channels.  
7
Instalar  
Idioma  
Sintonia  
Instalar  
Idioma  
Sintonia  
Auto Instalar  
Editar Canal  
Auto Instalar  
Installation  
Langue  
Installation  
Langue  
Mode synt.  
Installation auto  
Mode synt.  
Installation auto  
Editer progr.  
POWER  
FORMAT CLOCK SLEEP GUIDE  
AV  
SAP  
CC  
INFO  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
A/D  
MENU  
OK  
toggles between  
MENU  
HELPFUL HINT  
The Language control only makes the TV on-screen  
Menu items appear in English, Spanish, or French  
text.  
digital and analog  
mode  
< >  
MUTE  
VOL  
CH  
It does not change the other on-screen text  
languages such as Closed Caption (CC) TV  
programmes.  
Press A/D button on the remote control to toggle  
between Digital and Analog Mode.  
10  
HOW TO USE THE TUNER MODE CONTROL  
he TUNER MODE control lets you change the TV input signal to ANTENNA or CABLE mode. It is important  
Tthat you know which type of signal to look for (Cable or Antenna).  
Follow these steps for Digital Mode and Analog Mode  
Digital Mode  
Analog Mode  
Press MENU button on the remote control to  
display the onscreen menu.  
Language  
Tuner Mode  
Auto Install  
Language  
1
Tuner Mode  
Auto Install  
Channel Edit  
Press CURSOR < or > to scroll through  
the onscreen menu until you see Install  
highlighted.  
2
DTV Setup  
Press CURSOR > to display the Install menu  
features.  
3
Press CURSOR < or > to scroll through the  
Install features until you see Tuner Mode  
highlighted.  
Install  
Language  
Tuner Mode  
Auto Install  
Channel Edit  
Install  
Language  
Tuner Mode  
Auto Install  
4
Press CURSOR > to select Antenna or Cable.  
5
6
When finished, press MENU button on the  
remote control twice to exit the menu from  
the TV screen.  
POWER  
FORMAT CLOCK SLEEP GUIDE  
AV  
SAP  
CC  
INFO  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
A/D  
MENU  
OK  
toggles between  
digital and analog  
mode  
MENU  
< >  
MUTE  
VOL  
CH  
1
2
5
8
0
3
4
6
7
9
A/CH  
HELPFUL HINTS  
When CABLE is selected, channels 1-135 are  
available in Digital Mode and Channels 1-125 are  
available in Analog Mode.  
When ANTENNA is selected, channels 2-69 are  
available for both Digital and Analog Modes.  
When you install in either Digital or Analog  
mode, both Digital and Analog channels will be  
installed.  
Press A/D button on the remote control to toggle between  
Digital and Analog Mode.  
11  
CHANNEL EDIT (ADD OR SKIP CHANNELS)  
hannel Edit allows you to add or skip channels from your favorite list.  
C
Follow these steps for Analog Mode  
Follow these steps for Digital Mode  
Press MENU on the  
Press MENU on the  
remote control to  
remote control to  
Digital Mode  
Analog Mode  
1
2
1
display the onscreen  
menu.  
display the onscreen  
menu.  
Language  
Language  
Tuner Mode  
Auto Install  
Press CURSOR < or  
Press CURSOR < or >  
Tuner Mode  
Auto Install  
Channel Edit  
> to scroll through the  
onscreen menu until  
you see DTV Setup  
highlighted.  
to scroll through the  
onscreen menu until you  
see Install highlighted.  
2
DTV Setup  
Press CURSOR > to  
display the Channel  
Edit menu features.  
Press CURSOR >  
to highlight the Ch.  
Install menu features.  
3
4
5
6
7
3
4
DTV Setup  
Ch. Install  
Digital Audio  
Timer  
Install  
Press CURSOR < or  
> until the Channel you  
wish to Edit is displayed.  
Channel Edit  
Weak Dig Sig  
AutoLock  
Language  
Channel  
Skipped  
Tuner Mode  
Auto Program  
Channel Edit  
Press CURSOR < or  
Fact CH Reset  
Closed Caption  
Emerg Alert  
> to scroll through  
the Ch. Install features  
until you see Channel  
Edit highlighted.  
Press CURSOR > to  
highlight Skipped option.  
Use CURSOR > or < to  
toggle between on or off.  
Press CURSOR > to  
display the Channel Edit  
options.  
Channel Edit  
Channel  
Ch. Install  
5
6
Channel Edit  
Weak Dig Sig  
AutoLock  
3
If On is selected, the  
off  
Skipped  
channels will be skipped  
Press CURSOR < or  
Fact CH Reset  
when scrolling  
channels  
> to scroll the menu to  
highlight the channel you  
wish to add or skip.  
with the CH+ or CH- . If  
Off is selected, the channels  
will not be skipped when  
scrolling channels with the  
CH+ or CH- .  
Press CURSOR > or <  
to toggle between Added  
or Skipped. If Skipped is  
selected, the channels will  
be skipped when scrolling  
channels with the CH+ or  
CH- . If Added  
is selected, the channels  
will not be skipped when  
scrolling channels with the  
CH+ or CH- .  
7
Channel Edit  
When finished, press  
MENU button on the  
remote control three  
times to exit the menu  
from the TV screen.  
2
- 1 WCBS - DT  
Added  
35 - 1 MELCO  
8
Note : When you are in Analog  
Mode you can only add or skip  
programs in Analog Channels.  
POWER  
FORMAT CLOCK SLEEP GUIDE  
When finished, press  
MENU on the remote  
control four times to  
exit the menu from the  
TV screen.  
8
AV  
SAP  
CC  
INFO  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
A/D  
MENU  
OK  
toggles between  
digital and analog  
mode  
MENU  
< >  
Note : When you are in Digital  
Mode you can only add or skip  
programs in Digital Channels.  
MUTE  
VOL  
CH  
HELPFUL HINT  
It is important to auto install the TV (Refer page 9) before you try to Edit  
the Channels. If auto installation is not done, Channel Edit will show an  
error message : Favorite Channel list is empty. You must Auto Install.  
Press A/D button on the remote control to toggle between Digital and  
Analog Mode.  
12  
AUTO CHRON (SYNCHRONISATION OF TIME)  
uto Chron allows you to set the clock of the TV automatically for automatic selection, there will be queries for  
AChannel, Time Zone and Day Light saving. After successful setup, Auto Chron will automatically maintain the  
correct time. This feature is ONLY available in Digital Mode.  
Digital Mode  
Press MENU button on the remote  
control to display the onscreen menu.  
1
Press CURSOR < or > to scroll  
through the onscreen menu until you  
2
see DTV Setup highlighted.  
Press CURSOR > followed by CURSOR  
< or > to scroll through the DTV Setup  
DTV Setup  
3
4
5
features until you see Timer highlighted.  
Press CURSOR > followed by  
CURSOR < or > until Auto Chron is  
highlighted.  
DTV Setup  
Ch. Install  
Digital Audio  
Timer  
Auto Chron  
Time Zone  
Daylight Sav.  
Press CURSOR > followed by the  
NUMERIC buttons on the  
remote control to enter the channel  
number which has the time you want your  
TV to be synchronized to.  
Closed Caption  
Emerg Alert  
Timer  
When finished, press MENU button on  
the remote control three times to exit the  
menu from the TV screen.  
Auto Chron  
Time Zone  
Daylight Sav.  
Enter Channel  
0 - 0  
6
POWER  
FORMAT CLOCK SLEEP GUIDE  
AV  
SAP  
CC  
INFO  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
A/D  
MENU  
OK  
toggles between  
digital and analog  
mode  
MENU  
< >  
MUTE  
VOL  
CH  
1
2
5
8
0
3
4
6
NUMERIC  
7
9
A/CH  
HELPFUL HINT  
Press A/D button on the remote control to toggle between  
Digital and Analog Mode.  
13  
TIMER - TIME ZONE  
imer feature allows you to select the time zone you are in. This Feature is ONLY available in Digital Mode.  
T
1
2
Digital Mode  
Press MENU button on the remote  
control to display the onscreen menu.  
POWER  
Press CURSOR < or > to scroll  
FORMAT CLOCK SLEEP GUIDE  
through the onscreen menu until you  
see DTV Setup  
highlighted.  
AV  
SAP  
CC  
INFO  
Press CURSOR > followed by  
CURSOR < or > to scroll through  
the DTV Setup features until you see  
Timer highlighted.  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
3
DTV Setup  
MENU  
OK  
MENU  
Press CURSOR > followed by  
CURSOR < or > until Time Zone is  
highlighted.  
< >  
DTV Setup  
Ch. Install  
Digital Audio  
Timer  
Auto Chron  
Time Zone  
Daylight Sav.  
4
5
MUTE  
Press CURSOR > repeatedly to select  
the Time Zone you are in. Choices  
include Central, Mountain, Pacific,  
Alaska, Hawaii, Atlantic and Eastern.  
VOL  
CH  
Closed Caption  
Emerg Alert  
When finished, press MENU button on  
the remote control four times to exit the  
menu from the TV screen.  
Timer  
6
Auto Chron  
Time Zone  
Daylight Sav.  
Pacific  
TIMER - DAYLIGHT SAVING  
aylight Saving feature in Digital Mode allows you to adjust the timer on the TV an hour ahead of the official  
Dstandard time. Daylight Saving is ONLY available in Digital Mode.  
Digital Mode  
Press MENU button on the remote  
control to display the onscreen menu.  
1
POWER  
Press CURSOR < or > to scroll  
through the onscreen menu until you  
see DTV Setup highlighted.  
FORMAT CLOCK SLEEP GUIDE  
2
AV  
SAP  
CC  
INFO  
Press CURSOR > followed by CURSOR  
< or > to scroll through the DTV Setup  
features until you see Timer highlighted.  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
3
4
5
DTV Setup  
DTV Setup  
Ch. Install  
Digital Audio  
Timer  
MENU  
OK  
MENU  
Press CURSOR > followed by  
CURSOR < or > until Daylight Sav is  
highlighted.  
< >  
Auto Chron  
Time Zone  
Daylight Sav.  
MUTE  
Press CURSOR > to select On or  
Off. If Daylight Saving is set to On,  
the Timer on the TV will display One hour  
ahead of the actual time. If Daylight  
Saving is set to Off, the Timer on the TV  
will display the actual Time set.  
VOL  
CH  
Closed Caption  
Emerg Alert  
Timer  
Auto Chron  
Time Zone  
Daylight Sav.  
on  
When finished, press MENU button on  
the remote four times to exit the menu  
from the TV screen.  
6
Please be reminded to set Daylight Saving to Off  
after the Daylight Saving Season.  
14  
HOW TO ADD OR SKIP WEAK DIGITAL SIGNAL  
igital broadcasting is still new. It is not uncommon for a broadcaster to only send out a digital signal for part of  
Da day. The reception could also come and go. If you program your channels when the signal is not being sent  
or is weak it will not be saved in your channel setup. Using the Weak Digital Signal feature here, you can add those  
channels with weak or no signals to your channel list. Adding or skipping Weak Digital Signal can ONLY be  
done in Digital Mode.  
Digital Mode  
Press MENU button on the remote  
control to display the onscreen menu.  
POWER  
1
Press CURSOR < or > to scroll  
through the onscreen menu until you  
see DTV Setup highlighted.  
FORMAT CLOCK SLEEP GUIDE  
2
AV  
SAP  
CC  
INFO  
Press CURSOR > to display the DTV  
Setup menu features.  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
DTV Setup  
3
MENU  
OK  
MENU  
Press CURSOR < or > to  
scroll through the DTV SETUP  
features until you see Ch. Install  
highlighted. Press CURSOR > to display  
Ch. Install features.  
< >  
4
MUTE  
DTV Setup  
Ch. Install  
Digital Audio  
Timer  
Closed Caption  
Emerg Alert  
VOL  
CH  
Channel Edit  
Weak Dig Sig  
AutoLock  
Press CURSOR < or > to scroll  
through the DTV Setup features until you  
see Weak Dig Sig highlighted.  
1
2
5
8
0
3
5
Fact CH Reset  
4
6
Press CURSOR > to display the Weak  
Dig Sig options.  
7
9
6
7
8
A/CH  
Use CURSOR < or > to highlight the  
channel you wish to add or skip.  
Use CURSOR > to toggle between  
Added or Skipped. If Skipped is selected  
the channels will be skipped when scrolling  
channels with CH+ or CH-. If Added is  
selected the channels will not be skipped when  
scrolling channels with CH+ or CH-.  
Ch. Install  
Channel Edit  
Weak Dig Sig  
AutoLock  
Fact CH Reset  
When finished, press MENU button  
on the remote five times to exit the menu  
from the TV screen.  
9
Weak Dig Sig  
5
6
7
8
9
Signal  
Strength  
Skipped  
HELPFUL HINTS  
When no transmission is received from the  
broadcaster, the message, 'NO PROGRAM'  
will appear on the TV screen.  
Press A/D button on the remote control to toggle  
between Digital and Analog Mode.  
15  
EMERGENCY ALERT SETTING  
mergency Alert lets you display or discard emergency alerts for Low or Medium priority.  
EThis feature is ONLY available in Digital mode.  
Digital Mode  
Press MENU button on the remote control  
POWER  
to display the onscreen menu.  
1
Press CURSOR < or > to scroll through  
the onscreen menu until you see DTV Setup  
menu highlighted.  
FORMAT CLOCK SLEEP GUIDE  
2
AV  
SAP  
CC  
INFO  
Press CURSOR > to display the DTV  
Setup menu features.  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
DTV Setup  
3
MENU  
OK  
MENU  
Press CURSOR < or > to scroll through the  
DTV Setup features until you see Emerg  
Alert highlighted.  
DTV Setup  
Ch. Install  
Digital Audio  
Timer  
Closed Caption  
Emerg Alert  
< >  
4
Medium  
Low  
MUTE  
Press CURSOR > to enter the the Emerg  
Alert sub menu.  
VOL  
CH  
5
6
7
Press CURSOR < or > to highlight either  
Medium or Low.  
Emerg Alert  
Medium  
Low  
Press CURSOR > to switch between On  
or Off. If On is selected, the TV will display  
the alert of that priority.  
on  
When finished, press MENU buttion on the  
remote control four times to exit the menu  
from the TV screen.  
8
* Emergency Alert will not be visible if no  
broadcast is received or when the TV is in  
Stanby mode.  
FACTORY CHANNEL RESET  
actory Channel Reset feature lets you erase the contents of the master, user and favorite channel lists. This restores the  
FTV to the initial state before the first Auto Program operation. This feature is ONLY available in Digital Mode. For  
instructions on how to Auto Install the TV again, refer to page 9.  
Digital Mode  
Press MENU on the remote control to  
display the onscreen menu.  
1
2
POWER  
Press CURSOR < or > to scroll  
through the onscreen menu until you see  
DTV Setup highlighted.  
FORMAT CLOCK SLEEP GUIDE  
AV  
SAP  
CC  
INFO  
DTV Setup  
Press CURSOR > to display the Ch.  
Install menu features.  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
3
DTV Setup  
Ch. Install  
Digital Audio  
Timer  
Closed Caption  
Emerg. Alert  
MENU  
OK  
MENU  
Press CURSOR < or > to scroll through  
the Ch. Install features until you see Fact  
CH Reset highlighted.  
4
< >  
MUTE  
Press CURSOR > to clear all  
DTV settings OR Press the Menu button  
on the remote control to maintain the  
DTV settings.  
VOL  
CH  
5
Ch. Install  
Channel Edit  
Weak Dig Sig  
AutoLock  
HELPFUL HINTS  
Fact CH Reset  
<clear all DTV ?  
“menu” key to  
maintain DTV>  
Press A/D button on the remote control to toggle  
between Digital and Analog Mode.  
16  
DIGITAL AUDIO (SELECTING AUDIO LANGUAGES)  
igital Audio allows you to switch to another audio language when it is available. This feature is ONLY available in Digital  
DMode.  
Digital Mode  
Press MENU button on the remote  
control to display the onscreen menu.  
1
2
POWER  
Press CURSOR < or > to scroll  
through the onscreen menu until you  
see DTV Setup highlighted.  
FORMAT CLOCK SLEEP GUIDE  
AV  
SAP  
CC  
INFO  
Press CURSOR > to display the  
DTV Setup menu features.  
AUTO  
SOUND  
AUTO  
PICTURE  
3
A/D  
DTV Setup  
Press CURSOR < or > to scroll  
through the DTV SETUP features until  
you see Digital Audio highlighted.  
MENU  
OK  
MENU  
4
DTV Setup  
Ch. Install  
Digital Audio  
Timer  
Closed Caption  
Emerg Alert  
< >  
Multi Lingual  
Press CURSOR > to select the  
language you want to hear.  
MUTE  
5
VOL  
CH  
Digital Audio  
Multi Lingual  
English  
HELPFUL HINTS  
This is only for programs that are  
shown in more than one audio  
language.  
ACTIVE CONTROL OPTIONS  
ctive control options adjusts the picture quality according to the signal strength coming in.  
A
This feature is ONLY available in Analog Mode.  
Analog Mode  
Press MENU button on the remote control to  
display the onscreen menu.  
POWER  
1
Press CURSOR < or > to scroll through  
the onscreen menu until you see Features  
highlighted.  
FORMAT CLOCK SLEEP GUIDE  
Timer  
AutoLock  
Active Control  
2
AV  
SAP  
CC  
INFO  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
Press CURSOR > or < to display the  
Features menu.  
MENU  
OK  
3
4
5
MENU  
Press CURSOR < or > repeatedly until you  
see Active Control highlighted.  
< >  
MUTE  
Press CURSOR > or < to toggle the Active  
Control to On and Off. When On is  
selected, the TV will automatically adjust the  
picture quality according to the signal strength  
received.  
VOL  
CH  
Features  
Timer  
AutoLock  
Active Control  
On  
HELPFUL HINTS  
Press A/D button on the remote  
control to toggle between Digital  
and Analog Mode.  
When finished, press MENU button on the  
remote control twice to exit the menu from  
the TV screen.  
6
17  
PICTURE MENU CONTROLS  
o adjust your TV picture controls, select a channel and use the Picture Menu Controls listed below. Your selection is  
Tstored as Personal.  
Press MENU button on the remote control to  
display the onscreen menu.  
Digital and Analog Mode  
1
POWER  
Press CURSOR < or > to until the Picture  
menu feature is highlighted.  
2
FORMAT CLOCK SLEEP GUIDE  
AV  
SAP  
CC  
INFO  
Press CURSOR > or < to adjust  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
3
Brightness Control - until the darkest parts of the  
picture are as bright as you want.  
MENU  
OK  
MENU  
Color Control - to add or remove color.  
< >  
Picture Control - until the lightest parts of the  
MUTE  
picture show good detail.  
VOL  
CH  
Sharpness Control - to improve sharpness in the  
picture.  
Tint Control - adjust natural skin tones in the  
picture quality.  
Note : Tint is not available in Digital Mode  
Color Temp Control - to select Normal, Cool,  
or Warm picture preferences. For Normal, whites  
will mainain their whiteness;  
Cool will make the whites bluish; and Warm will  
make the whites reddish.  
DNR  
DNR - When set to On Dynamic Noise Reduction  
helps to eliminate "noise" from the picture.  
Contrast + Control - when set to On, the  
Contrast + control helps to “sharpen” the  
picture quality. The black portions of the picture  
become richer in darkness and the whites become  
brighter.  
HELPFUL HINTS  
Press A/D button on the remote control to toggle  
between Digital and Analog Mode.  
AUTO PICTURE  
hether you’re watching a movie or a sporting event, your TV has automatic video control settings to enhance  
Wyour current program source or content.  
POWER  
Press AUTO PICTURE button on the  
remote control. The current Auto Picture  
setting will display on the screen.  
FORMAT CLOCK SLEEP GUIDE  
1
2
AV  
SAP  
CC  
INFO  
Press AUTO PICTURE repeatedly to  
select either Personal, Movies, Sports,  
Weak Signal or Multimedia picture  
settings.  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
AUTO  
PICTURE  
MENU  
OK  
MUTE  
VOL  
CH  
NOTE: The way you choose to set the Picture Menu  
Controls will become your Personal setting.  
18  
SOUND MENU CONTROLS  
o adjust your TV sound, use the Sound Menu Controls listed below. Your selection is stored as Personal.  
T
1
2
3
Analog Mode  
Digital Mode  
Press MENU button on the remote control  
to display the onscreen menu.  
Press CURSOR > to until the Sound menu  
feature is highlighted.  
Press CURSOR > or < to adjust  
Treble: Enhance the high frequency sounds.  
Bass: Enhance the low frequency sounds.  
Balance: Level of sound coming from the left  
and right speakers.  
AVL: (Auto Volume Leveler) When turned  
On, AVL will level out the sound being heard  
when sudden change in volume occurs during  
commercial breaks or channel changes.  
L
R
Incr. Surround: Select Incr. Surround or  
Stereo settings if you're in Stereo mode.  
Select Mono or Spatial if you're in Mono mode.  
Incr. Surround  
Incr. Surround  
SAP: Secondary Audio Programming is sent as  
a third audio channel, a SAP signal can be heard  
apart from the current TV program sound.  
or Stereo  
or  
Spatial  
or Mono  
Note: If SAP is not present on a selected show,  
No SAP will be displayed on the TV screen.  
POWER  
FORMAT CLOCK SLEEP GUIDE  
Sound: toggles between Stereo or Mono  
settings.  
AV  
SAP  
CC  
INFO  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
Note: If Stereo is not present on a selected  
show and the TV is in Stereo mode, the sound  
coming from the TV will remain in the Mono  
mode.  
MENU  
OK  
MENU  
< >  
MUTE  
HELPFUL HINTS  
Press A/D button on the remote control to toggle  
VOL  
CH  
between Digital and Analog Mode.  
AUTO SOUND  
he Auto Sound feature allows the listener to select between four different pre-set sound options.  
T
1
POWER  
Press AUTO SOUND button on the remote  
control. The current Auto Sound setting will  
be displayed in the middle of the TV screen.  
FORMAT CLOCK SLEEP GUIDE  
AV  
SAP  
CC  
INFO  
AUTO  
SOUND  
AUTO  
SOUND  
AUTO  
PICTURE  
Press AUTO SOUND repeatedly to  
toggle between the four settings. (Personal,  
Theatre, Music, or Voice).  
A/D  
MENU  
OK  
2
NOTE: The way you choose to set the Sound Menu  
MUTE  
Controls will become your Personal setting.  
VOL  
CH  
19  
UNDERSTANDING AUTOLOCK CONTROLS  
utoLock is a feature that lets the TV receive and process data sent by broadcasters or other program providers with program content  
Aadvisory. When programmed by the viewer, a TV with AutoLock can respond to the content advisory and block program content  
that may be found objectionable (such as offensive language, violence, sexual situations, etc.). This feature is useful for adults to prevent  
certain types of programs from being viewed by children.  
AutoLock offers various BLOCKING controls to choose from:  
Access Code - An Access Code must be set to prevent children from unblocking questionable or censored programming set by their  
parents.  
Channel Block - After an access code has been programmed, you cannot block individual channels including the A/V inputs.  
Clear All - Lets you clear all channels being blocked from your viewing set with the Channel Block Control.  
Block All - Lets you block ALL channels except A/V inputs.  
No Rating / Unrated - ALL programing with no content advisory data can be blocked if NO RATING / Unrated is set to ON.  
Movie Ratings - Certain blocking options exist which will block programming based on ratings patterned by the Motion Pictures  
Association of America (MPAA).  
TV Ratings - Like the Movie Ratings, programs can be blocked from viewing using standard TV ratings set by TV broadcasters.  
MOVIE RATINGS  
TV RATINGS  
G: General Audience - All ages admitted. Suitable for all ages.  
TV-Y : Designed for a very young audience, including children  
ages 2-6  
PG: Parental Guidance Suggested - Contains material  
unsuitable for younger children.  
TV-Y7: Appropriate for children age 7 and above who have  
acquired the development skills needed to distinguish between  
make-believe and reality.  
PG-13: Parents Strongly Cautioned - Contains material  
acquired the development skills needed to distinguish between  
make-believe and reality.  
unsuitable for children under the age of 13.  
R: Restricted - Suitable for adults above 17 years of age only.  
TV-G : Suitable for most audiences. Contains little or no violence,  
no strong language, and little or no sexual dialogue or situations.  
NC-17: No one under the age of 17 will be admitted.  
TV-PG: Contains material unsuitable for younger children.  
Could contain Moderate violence (V), some sexual situations (S),  
infrequent coarse language (L), or some suggestive dialogue (D).  
X: Adults Only - Contains one or more of the following: very  
graphic violence, very graphic and explicit or indecent sexual acts,  
very coarse and intensely suggestive language.  
TV-14: Contains some material unsuitable for children under  
14 years of age. Contains one or more of the following: intense  
violence (V), intense sexual situations (S), strong coarse language  
(L), or intensely suggestive dialogue (D).  
TV-MA - Viewed by adults and therefore may be unsuitable for  
children under 17. Contains one or more of the following: graphic  
violence (V), explicit sexual situations (S), or crude indecent  
language (L).  
20  
AUTOLOCK  
utoLock allows the viewer to block out any channels. A channel blocked by the AutoLock control cannot be viewed  
Auntil a correct access code is used to unlock the channel for viewing.  
Follow these steps for Digital Mode  
Follow these steps for Analog mode  
Press MENU button on  
the remote control to  
display the onscreen menu.  
Press MENU button on  
the remote control to  
display the onscreen menu.  
Digital Mode  
Analog Mode  
1
2
1
2
Main  
Main  
Picture  
Sound  
Timer  
Rotation  
Press CURSOR < or  
> to scroll through the  
onscreen menu until you  
see Features highlighted.  
Press CURSOR < or  
> to scroll through the  
onscreen menu until  
you see DTV Setup  
highlighted. Press  
Features  
Install  
AutoLock  
Close Cap.  
Active Control  
DTV Setup  
Ch. Install  
Channel Edit  
Weak Dig Sig  
Features  
Time  
Rotation  
AutoLock  
Press CURSOR > to  
display the Features  
menu.  
CURSOR > to display  
DTV Setup features.  
Access Code  
_ _ _ _  
3
4
5
AutoLock  
Fact CH Reset  
Password _ _ _ _  
Incorrect  
Active Control Incorrect  
Press CURSOR < or  
> to scroll through the  
DTV Setup features until  
Ch. Install is highlighted.  
Press CURSOR < or >  
repeatedly until you  
see AutoLock highlighted.  
3
Features  
Ch. Install  
Time  
Rotation  
New Code  
_ _ _ _  
Channel Edit  
Weak Dig Sig  
AutoLock  
Password _ _ _ _  
Correct  
AutoLock  
Active Control  
Fact CH Reset  
Press CURSOR > to  
enter the AutoLock  
mode.  
Press CURSOR >  
followed by CURSOR  
< or > until  
you see AutoLock  
4
AutoLock  
Block Channel  
"Access Code _ _ _ _" will  
appear.  
highlighted.  
Press CURSOR > to  
enter the AutoLock  
mode.  
Using the NUMERIC  
buttons on the remote  
control enter the access  
code. 0711 is the default.  
The first time you enter  
the code, Incorrect will  
appear on the screen.  
Enter the same code again.  
You will be prompted to  
enter a new code.  
5
6
POWER  
"Password _ _ _ _" will  
appear.  
FORMAT CLOCK SLEEP GUIDE  
Press CURSOR >  
followed by the  
NUMERIC buttons on the  
AV  
SAP  
CC  
INFO  
6
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
A/D  
remote control to enter  
the access code. 0711  
is the default. The first  
time you enter the code,  
Incorrect will appear on  
the screen. Enter the same  
code again. Correct will  
be displayed. Now can  
proceed to block channels.  
MENU  
OK  
toggles between  
digital and analog  
mode  
MENU  
Use the NUMERIC  
buttons on the remote  
control enter the access  
code of your choice.  
Enter the same code a  
second time to confirm  
it. Once the new code is  
confirmed, the AutoLock  
menu will appear. You can  
now access the functions  
available in the menu.  
< >  
7
MUTE  
VOL  
CH  
1
2
5
8
0
3
NUMERIC  
4
6
7
9
A/CH  
Note : Remember this new code  
which you have set. You can use  
this code to access AutoLock  
features in both Digital and Analog  
mode. If you forget the new code  
you have set, key 0711 to access  
AutoLock features.  
HELPFUL HINTS  
When you are in Digital Mode you can only  
AutoLock Digital Channels.  
When you are in Analog Mode you can  
only AutoLock Analog Channels.  
21  
AUTOLOCK - BLOCKING CHANNELS  
fter you have set your personal access code (see previous page), you are now ready to select the channels you want  
Ato block.  
Follow these steps for Analog Mode  
Follow these steps for Digital Mode  
Digital Mode  
Analog Mode  
After Setting your  
personal access code  
(see previous  
page), press CURSOR  
< or > until you  
see Block Channel  
highlighted.  
After Setting your  
personal access code (see  
previous page), press  
CURSOR < or > until  
you see Block Channel  
highlighted.  
AutoLock  
Block Channel  
1
1
Press CURSOR < or  
> to select channels  
you wish to block. Press  
CURSOR > or < to  
select between Block and  
Unblock.  
Block Channel  
All Channels  
Press CURSOR >  
to enter the Block  
Channel menu. Press  
CURSOR > or < to  
Block or unBlock the  
channel.  
2
Blocked  
2
- 1 WCBS - DT  
2
35 - 1 MELCO  
59 - 1  
Channel 4  
Blocked by AutoLock  
Channel Block  
Access Code  
_ _ _ _  
Press CURSOR >  
or < to select Block or  
Unblock.  
Press CURSOR <  
or > to highlight the  
channel you wish to  
Block or Unblock.  
3
3
Blocked Channel  
35 - 1 MELCO  
When finished, press  
MENU on the remote  
control three times to  
exit the menu from the  
TV screen.  
4
Press CURSOR > or  
< to select Block or  
Unblock.  
4
POWER  
FORMAT CLOCK SLEEP GUIDE  
When Block  
When finished, press  
MENU button on the  
remote control three  
times to exit the menu  
from the TV screen.  
is selected, a message will  
appear to show you the  
channel that has been  
Blocked.  
AV  
SAP  
CC  
INFO  
5
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
A/D  
MENU  
OK  
toggles between  
digital and analog  
mode  
MENU  
Note : When you are in Analog  
Mode you can only block Analog  
Channels.  
< >  
When Block is  
MUTE  
selected, a message will  
appear to show you  
the channel that has  
been Blocked.  
VOL  
CH  
1
2
5
8
0
3
4
6
Note : When you are in Digital  
Mode you can only block  
Digital Channels.  
7
9
A/CH  
HELPFUL HINTS  
If you forget your code, the 0711 is the default  
and can be used to enter and create a new access  
code.  
22  
BLOCK / CLEAR ALL CHANNELS AT THE SAME TIME  
fter blocking specific channels there may come a time when you want to block or clear all the channels at the  
Asame time. This can be done only after you have entered your access code and the AutoLock features are  
displayed on the screen (refer to page 21).  
Follow these steps for Digital Mode  
Follow these steps for Analog mode  
Digital Mode  
Analog Mode  
Press CURSOR > to select  
Block channel. Press the  
CURSOR > button to  
enter the Block Channel  
menu.  
Press CURSOR > to  
select either Clear All or  
Block All.  
AutoLock  
Block Channel  
1
1
If Clear All is set to on, all  
channels will be viewable.  
2
Press CURSOR < or >  
If Block All is set to on  
all available channels will be  
blocked from viewing.  
until All Channels  
is highlighted. Press  
Clear All  
Block All  
On  
Off  
Block Channel  
All Channels  
2
Unblock  
2
- 1 WCBS - DT  
35 - 1 MELCO  
59 - 1  
CURSOR > or < to  
toggle between Block and  
Unblock. If Unblock is  
selected, all channels will  
be viewable. If Block is  
selected, ALL available  
channels will be blocked  
from viewing.  
POWER  
When finished, press MENU  
FORMAT CLOCK SLEEP GUIDE  
on the remote control four  
times to exit the menu from  
the TV screen.  
3
AV  
SAP  
CC  
INFO  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
MENU  
MENU  
OK  
< >  
MUTE  
VOL  
CH  
When finished, press  
MENU four times to exit  
the menu.  
3
BLOCK OPTIONS  
lock Options allows you to block programs by ratings instead of channels. This can be done only after you have  
Bentered your access code and AutoLock feature is displayed on the screen.  
Note : To access this menu for both Digital and Analog Mode, follow the steps for Analog mode (Page 21).  
Analog Mode  
Digital Mode  
Follow these steps for both Digital and Analog Mode  
Press CURSOR < or > until you see Block  
Options highlighted.  
Unrated  
No rating  
Blocking  
1
Press CURSOR < or > to display the Block  
Options (Unrated, No Rating or Blocking) menu.  
Unrated  
No rating  
Blocking  
2
Press CURSOR < or > until you see the  
desired Option is highlighted. When highlighted,  
each feature can be turned On or Off using  
CURSOR > or < on the remote control.  
POWER  
3
FORMAT CLOCK SLEEP GUIDE  
AV  
SAP  
CC  
INFO  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
When finished, press MENU four times to exit  
the menu.  
MENU  
OK  
4
MENU  
< >  
MUTE  
HELPFUL HINTS  
Press A/D button on the remote control to toggle  
VOL  
CH  
between Digital and Analog Mode.  
23  
MOVIE RATINGS  
he AutoLock feature can block programs based on the Movie Industry ratings. Once you have entered your  
Taccess code and the AutoLock features are displayed on the screen.  
Note : To access this menu for both Digital and Analog Mode, follow the steps for Analog mode (Page 21).  
Follow these steps for Digital Mode  
Follow these steps for Analogue mode  
Press CURSOR < or  
> until you see Block by  
Rating highlighted.  
Press CURSOR < or >  
until you see Movie Rating  
highlighted.  
Analog Mode  
Digital Mode  
1
1
AutoLock  
Setup Code  
Movie Rating  
TV Rating  
G
PG  
PG-13  
R
Press the CURSOR > to  
display the Movie Rating  
options (G, PG, PG-13, R,  
NC17, or X).  
Press CURSOR > to  
display the Movie Rating  
options (G, PG, PG-13, R,  
NC17, or X).  
G
PG  
PG-13  
R
NC-17  
X
2
2
Block Options  
NC-17  
X
Press CURSOR < or  
> to highlight any of the  
Movie Rating options.  
When highlighted, all these  
options can be turned On  
(which will allow blocking)  
or Off (which will allow  
viewing).  
Press CURSOR < or > to  
highlight any of the Movie  
Rating options. When  
highlighted, all these options  
can be turned On (which will  
allow blocking) or Off (which  
will allow viewing).  
Movie Rating  
Movie Rating  
G
PG  
PG-13  
R
3
G
PG  
PG-13  
R
NC-17  
X
3
NC-17  
X
G
Use CURSOR > on the  
remote control to turn the  
rating option On or Off.  
POWER  
Press CURSOR > on the  
remote control to turn  
the rating option On or  
Off.  
4
FORMAT CLOCK SLEEP GUIDE  
4
AV  
SAP  
CC  
INFO  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
A/D  
MENU  
OK  
toggles between  
digital and analog  
mode  
MENU  
< >  
MUTE  
VOL  
CH  
1
2
5
8
0
3
4
6
7
9
A/CH  
HELPFUL HINTS  
Press A/D button on the remote control to toggle  
between Digital and Analog Mode.  
24  
TV RATINGS  
he AutoLock feature can block programs based on the TV Industry ratings. When you have entered your access code  
and the AutoLock features are displayed on the screen (refer to page 22).  
T
Note : To access this menu for both Digital and Analog Mode, follow the steps for Analog mode (Page 21).  
Follow these steps for Digital Mode  
Follow these steps for Analog Mode  
Digital Mode  
Analog Mode  
Press CURSOR < or >  
Press CURSOR < or >  
until you see TV Rating  
highlighted.  
until you see TV Rating  
highlighted.  
1
1
AutoLock  
Setup Code  
Movie Rating  
TV Rating  
TV-Y  
TV-Y7  
TV-G  
TV-PG  
TV-14  
TV-MA  
Block Options  
Press the CURSOR > to  
display the TV Rating options  
(TV-Y, TV-Y7, TV-G, TV-PG,  
TV-14 or TV-MA).  
Press the CURSOR > to  
display the TV Rating options  
(TV-Y, TV-Y7, TV-G, TV-PG,  
TV-14 or TV-MA).  
2
2
TV Rating  
TV-Y  
TV-Y7  
TV-G  
TV-PG  
TV-14  
TV-MA  
Press CURSOR < or > to  
highlight any of the TV Rating  
options. When highlighted,  
all these options can be  
turned On (which will allow  
blocking) or Off (which will  
allow viewing).  
Press CURSOR < or >  
until any of the TV Rating  
options is highlighted. All  
these highlighted options can  
be turned On (which will  
allow blocking) or Off  
3
3
(which will allow viewing).  
Press CURSOR > or < to  
turn the rating option On or  
Off.  
Press CURSOR > to turn  
the TV-Y or TV-G rating  
On or Off. OR press the  
CURSOR > to enter the  
sub-menus.  
4
4
POWER  
If the TV-Y7, TV-PG, TV-  
FORMAT CLOCK SLEEP GUIDE  
14 or TV-MA sub-menu  
is accessed, press  
CURSOR < or > to select  
one of the options (Block All,  
V, S, L, D or FV).  
5
AV  
SAP  
CC  
INFO  
If the TV-Y7, TV-PG, TV-14  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
or TV-MA  
sub-menu is accessed,  
press CURSOR < or > to  
select one of the options  
(Block All, V, S, L, D or FV).  
A/D  
5
MENU  
MENU  
OK  
toggles between  
digital and analog  
mode  
< >  
MUTE  
Press CURSOR > to turn  
VOL  
CH  
option On or Off.  
6
Press CURSOR > to turn  
option On or Off.  
1
2
5
8
0
3
4
6
6
7
9
A/CH  
HELPFUL HINTS  
Press A/D button on the remote control to toggle  
between Digital and Analog Mode.  
25  
HOW TO USE THE TIMER MENU CONTROLS  
our television comes with an onscreen clock. The TV can also be set to turn on or off at a specific time and tune  
Yto a specific channel when it powers itself on.  
Digital Mode  
Analog Mode  
Press the MENU button on the remote  
control to display the onscreen menu.  
1
2
3
4
5
6
Press the CURSOR < or > button until  
Features is highlighted.  
Timer  
Timer  
Rotation  
AutoLock  
AutoLock  
Auto Control  
Press the CURSOR > button to  
display the Features menu.  
DTV Setup  
Press the CURSOR > button to  
display the Timer menu.  
Features  
Timer  
Features  
Timer  
Press the CURSOR > button to  
access the Timer menu.  
Rotation  
AutoLock  
Rotation  
AutoLock  
AutoControl  
Press the CURSOR < or >¸  
until one of the Timer controls (Time,  
Start Time, Stop Time, Channel, Activate, or  
Displayhighlight) is hightlighted.  
Press the CURSOR > to display the menu  
for the selected item. Make adjustments to  
the selected items by following the steps  
below.  
7
Time: Enter the current time using the  
NUMERIC buttons. Use the CURSOR  
> or < to toggle the AM and PM setting.  
DTV  
Start Time: Use the NUMERIC buttons to  
enter  
the time you want the TV to turn  
itself On. Use the CURSOR > or < to  
toggle the AM and PM setting.  
POWER  
FORMAT CLOCK SLEEP GUIDE  
Stop Time: Use the NUMERIC buttons to  
enter the time you want the TV to turn itself  
Off. Use the CURSOR > or < to toggle the  
AM and PM setting.  
AV  
SAP  
CC  
INFO  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
MENU  
A/D  
MENU  
OK  
< >  
toggles between  
digital and analog  
mode  
Channel: In Digital Mode, use CH +  
or CH- to select DTV which is the last  
viewed digital channel. In Analog Mode,  
use the NUMERIC buttons or the CH + or  
CH- buttons to enter the startup channel.  
MUTE  
VOL  
CH  
1
2
5
8
0
3
4
6
NUMERIC  
7
9
Activate: Set the timer to turn itself Off,  
Once or Daily. Press the CURSOR > or <  
to select Once, Daily, or Off.  
A/CH  
Display: Press the CURSOR > or <  
to toggle between On or Off. If On is  
selected, the time will be displayed all the  
time when the TV is on. When Off is  
selected, the time will only appear  
HELPFUL HINTS  
In Digital Mode : Before you turn off the TV you have to switch to  
the desired digital channel because the TV will wake up in the last  
viewed digital channel.  
when the INFO button is pressed.  
NOTE : Display is not available in Digital  
Mode.  
In Analog Mode : You can specify which channel to wake up to.  
Press A/D button on the remote control to toggle between Digital and  
Analog Mode.  
Press the MENU button on the remote  
control three times to remove the onscreen  
menu from the TV screen.  
8
26  
CLOSE CAPTIONING DISPLAY IN DIGITAL MODE  
hen in digital mode, you can assign display options to your closed captioning options.  
This feature is ONLY available in Digital Mode.  
W
1
Digital Mode  
Press MENU button on the remote control  
POWER  
to display the onscreen menu.  
FORMAT CLOCK SLEEP GUIDE  
Ch. Install  
Press CURSOR < or > until you see  
DTV Setup highlighted.  
Digital Audio  
Timer  
Closed Caption  
Emerg Alert  
AV  
SAP  
CC  
INFO  
2
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
DTV Setup  
Press CURSOR > to display the DTV  
MENU  
OK  
MENU  
Setup options.  
3
4
DTV Setup  
Ch. Install  
Digital Audio  
Timer  
Closed Caption  
Emerg Alert  
< >  
Display  
Service  
Caption Option  
Caption Text  
CC Background  
Press CURSOR < or > until you  
see Close Caption highlighted. Press  
CURSOR > to enter Display menu  
options.  
MUTE  
VOL  
CH  
Press CURSOR > to toggle to the options  
that you want – Off, Always on or On  
when muted.  
Closed Caption  
Display  
Service  
Caption Option  
Caption Text  
CC Background  
Always On  
5
6
HELPFUL HINTS  
An alternative way of activating  
closed caption is by pressing the CC  
button on the remote control.  
When finished, press MENU button on the  
remote control to exit the menu from the  
TV screen  
.
Close Captions may take 10 - 20  
seconds to appear on the TV screen.  
CAPTION OPTION IN DIGITAL MODE  
aption Option lets you select the default option or options that you have assigned to your Close captioning  
Cservice. This feature is ONLY available in Digital Mode.  
Digital Mode  
Press MENU button on the remote control  
to display the onscreen menu.  
1
POWER  
FORMAT CLOCK SLEEP GUIDE  
Press CURSOR < or > until you see DTV  
Setup highlighted.  
Ch. Install  
Digital Audio  
Timer  
Closed Caption  
Emerg Alert  
2
3
4
AV  
SAP  
CC  
INFO  
AUTO  
SOUND  
AUTO  
PICTURE  
Press CURSOR > to display the DTV Setup  
options.  
A/D  
DTV Setup  
MENU  
OK  
MENU  
DTV Setup  
Ch. Install  
Digital Audio  
Timer  
Closed Caption  
Emerg Alert  
Press CURSOR < or > until you  
see Close Caption highlighted. Press  
CURSOR > to enter Caption Option  
menu options.  
< >  
Display  
Service  
Caption Option  
Caption Text  
CC Background  
MUTE  
VOL  
CH  
Press CURSOR > to toggle to the options  
that you want – Use Default or Use  
Options.  
Closed Caption  
5
Display  
Service  
Caption Option  
Caption Text  
CC Background  
Use Option  
When Use Options is choosen, you will  
be prompted to select text size, color, opacity,  
edge color, type and CC background color.  
6
7
HELPFUL HINTS  
Press A/D button on the remote  
control to toggle between Digital and  
Analog Mode.  
When finished, press MENU button on the  
remote control to exit the menu from the TV  
screen  
.
27  
CLOSE CAPTIONING IN ANALOG MODE  
lose captioning in analog mode allows you to select the close caption setting while watching analog transmission.  
C
Analog Mode  
Press the MENU button on the remote  
control to display the onscreen menu.  
1
2
3
4
5
Press the CURSOR < or > button until  
Features is highlighted.  
Timer  
AutoLock  
Close Caption  
Active Control  
Press the CURSOR < or > button to  
display the Features menu.  
Press the CURSOR > button to  
display the Close Caption menu.  
Press the CURSOR > repeatedly to select  
one of the close caption settings namely CC  
Off, CC1, CC2 and CC Mute  
Features  
Timer  
CC Off : Turns Close Captioning Off.  
AutoLock  
Closed Caption  
Active Control  
CC1 and CC2 : Depending on the  
broadcaster, this displays the close caption  
languages available in the program at the  
time of broadcast.  
CC Mute : Displays close caption when the  
TV is muted.  
Press the MENU button on the remote  
control three times to remove the onscreen  
menu from the TV screen.  
POWER  
6
FORMAT CLOCK SLEEP GUIDE  
AV  
SAP  
CC  
INFO  
CC  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
MENU  
OK  
MENU  
< >  
MUTE  
VOL  
CH  
HELPFUL HINTS  
An alternative way of activating closed caption  
is by pressing the CC button on the remote  
control.  
Close Captions may take a while to appear on the  
TV screen.  
28  
SLEEPTIMER  
he SleepTimer feature allows you to set a timer to automatically turn the TV off after a period of time you choose  
T- 15, 30, 45, 60, 90, 120, 180 or 240 minutes.  
Digital and Analog Mode  
Press SLEEP button on the remote control to  
POWER  
display the sleeptimer menu.  
1
2
FORMAT CLOCK SLEEP GUIDE  
Press SLEEP button on the remote control  
SLEEP  
to select the amount of time (15, 30, 45, 60,  
AV  
SAP  
CC  
INFO  
90, 120, 180 or 240 minutes) before the TV  
automatically switches Off.  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
MENU  
OK  
Sleep 15  
NOTE: An onscreen countdown will appear during  
the last minute before the TV switches  
Off. If any button is pressed during the last  
minute of the countdown, the Sleep Timer  
setting will be cancelled.  
MUTE  
15, 30, 45, 60, 90, 120, 180,  
240  
VOL  
CH  
ROTATION  
ometimes the video transmitted to the TV screen might appear slightly tilted. The Rotation control lets you correct the  
Sproblem by adjusting the screen in a clockwise or counterclockwise direction.  
32PT9005D Only  
Press MENU button on the remote control to  
display the onscreen menu.  
1
Press CURSOR < or > until you see Features  
highlighted.  
Timer  
Rotation  
AutoLock  
Active Control  
2
Press CURSOR > to display feature menu.  
3
Active Control  
Press CURSOR < or > until you see Rotation  
control highlighted.  
4
Press CURSOR > or < to rotate the picture on the  
screen clockwise or counter clockwise.  
5
POWER  
Note : The amount of rotation will be minimal.  
FORMAT CLOCK SLEEP GUIDE  
Press MENU twice to exit the menu from the TV  
screen.  
6
AV  
SAP  
CC  
INFO  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
MENU  
OK  
MENU  
< >  
MUTE  
VOL  
CH  
HELPFUL HINTS  
Press A/D button on the remote  
control to toggle between Digital and  
Analog Mode.  
29  
HOW TO USE THE FORMAT CONTROL  
he format Control feature allows you to select the picture-format mode.  
T
Selecting a Picture Format Using the  
Remote Control  
POWER  
FORMAT CLOCK SLEEP GUIDE  
FORMAT  
Press FORMAT button on the remote  
AV  
SAP  
CC  
INFO  
control once to see the current picture-  
1
format mode.  
AUTO  
AUTO  
A/D  
SOUND  
PICTURE  
4:3  
Press FORMAT button repeatedly on the  
MENU  
OK  
remote control to select one of the screen  
format options namely 4:3, 4:3 Expand, 4:3  
Stretch and 16:9 Compress.  
2
MUTE  
VOL  
CH  
1
2
5
8
0
3
Picture-Format Modes  
4
6
4:3  
Shows picture in its original (4:3  
aspect ratio) format. You will see  
2 side borders on the TV screen.  
7
9
4:3 EXPAND  
A/CH  
4:3 Expand  
4:3 Stretch  
Expands the picture  
vertically.  
4:3 STRETCH  
4:3 STRETCH  
Expands the picture  
horizontally eliminating the  
side borders on both sides of the  
TV screen.  
16:9 Compress Expands the picture horizontally  
delivering a home-cinema  
experience. You will see 2 black  
borders at the top and bottom of  
the screen.  
16:9 COMPRESS  
16:9 COMPRESS  
HELPFUL HINTS  
Picture-format mode can only be activated when  
you are watching High-definition (HD) programs.  
Press A/D button on the remote control to toggle  
between Digital and Analog Mode.  
30  
INFORMATION BANNER AND ELECTRONIC PROGRAM GUIDE  
he Information Banner displays information of the program that is being transmitted. This feature is ONLY  
Tavailable in Digital.  
Digital Mode  
Information Banner  
Thu 1 June 08:38AM  
35-1  
MELCO  
1080i Norway wit....  
Press INFO button on the remote control once to see the  
HD  
CC  
No Rating  
Information Banner.  
1
Note : The Information Banner displays the channel number, time and  
features that are available in the program that is being shown. Feature  
logos that are lighted up show that the feature is available.  
INFORMATION BANNER  
Thu 1 June 08:38AM  
MELCO  
Electronic Program Guide  
Press GUIDE button on the remote control once to see the  
35-1  
Electronic Program Guide.  
2
1080i Norway wit....  
Note : The Electronic Program Guide displays the program schedule that  
will be broadcast on the channel.  
08:56AM - 09:01AM  
HD  
CC  
No Rating  
08:56AM - 09:01AM  
09:01AM - 09:06AM  
1080i Norway with PS .....  
1080 i LIP Sync. with PS...  
When any of these logos on the Information Banner and Electronic  
Program Guide are lighted up, it means the features are available.  
ELECTRONIC PROGRAM GUIDE  
High Definition Program.  
Surround Sound.  
POWER  
FORMAT CLOCK SLEEP GUIDE  
GUIDE  
INFO  
AV  
SAP  
CC  
INFO  
AUTO  
SOUND  
AUTO  
PICTURE  
A/D  
Close Captioning Text.  
MENU  
OK  
Dolby Digital Sound.  
MUTE  
VOL  
CH  
Signal strength the TV is receiving.  
HELPFUL HINTS  
The quality and accuracy of the information on the Information  
Banner and Electronic Program Guide are transmitted from  
broadcasters. You may see a difference in broadcast time if the  
broadcaster is from a different time zone area.  
If "No Information" appears on the screen when the INFO or GUIDE  
button on the remote control is pressed, it means the broadcaster is not  
providing any information.  
The INFO button can also be used to exit the menu display from the  
TV screen.  
31  
GLOSSARY  
Aspect Ratio  
The ratio between the width and height of the TV picture on the screen. In a normal TV set the aspect ratio is 4  
to 3 (4:3). The new aspect ratio in HDTV is 16:9 which resembles the aspect ratio in a movie theatre  
(Widescreen). New TV systems support both 4:3 and 16:9 aspect ratio and can automatically switch between  
them.  
Audio Video (A/V)  
A term often used when discussing a channel on a TV receiver or on video equipment, which has been  
especially designed to accept VCR audio-video signals. This channel automatically activates special circuitry  
within the TV set to prevent picture distortion and skewing. It is also used for audio-video processors, which  
handle both types of signals.  
ATSC  
ATSC: Advanced Television Systems Committee. Formed to establish technical standards for advanced  
television systems, including digital high definition television (HDTV).  
CVBS  
Composite Video Baseband Signal. In broadcast television this refers to the video signal,  
including the colour information and syncs  
DTV  
Digital television. Generic term that refers to all digital television formats, including high-definition television  
(HDTV) and standard-definition television (SDTV).  
DOLBY Digital  
Dolby Digital - Six-channel digital audio standard that is part of the U.S. digital television standard; also called AC-3 or Digital  
5.1. The channels consist of front left, front right, front center, surround or rear left, surround or rear right, and a separate  
subwoofer  
Digital Tuner  
HDTV  
A digital tuner serves as the decoder required to receive and display digital broadcasts. It can be included inside TV sets or  
via a set-top box.  
The generally agreed upon definition of HDTV is approximately twice the vertical and horizontal picture resolution of today’s  
NTSC TV, which essentially makes the picture twice as sharp. HDTV also has a screen ratio of 16:9 as compared with most of  
today’s TV screens, which have a screen ratio of 4:3. HDTV offers reduced motion artifacts (i.e. ghosting, dot crawl), and  
offers 5.1 independent channels of CD-quality stereo surround sound, (also referred to as AC-3).  
NTSC  
National television system committee. The organization that developed the analog television standard currently in use in the  
U.S., Canada, and Japan. Now generally used to refer to that standard. The NTSC standard combines blue, red, and green  
signals modulated as an AM signal with an FM signal for audio.  
Progressive Scan  
Resolution  
In Progressive Scanning all the horizontal scan lines are scanned on to the screen at one time. The Digital TV and HDTV  
Standards accept both Interlaced Scan and Progressive Scan broadcast and display methods.  
Resolution: A measurement of the finest (smallest) detail that is visible in a video image. TV Resolutions may be expressed as  
number of pixels in an image; or more commonly, “As Total Number of (horizontally scanned) Lines used to create the image.  
Standard Digital TV Resolutions:  
SDTV: 480i - The picture is 704x480 pixels, 480p - The picture is 704x480 pixels.  
HDTV: 720p - The picture is 1280x720 pixels, 1080i - The picture is 1920x1080 pixels, 1080p - The picture is 1920x1080  
pixels.  
32  
TROUBLESHOOTING TIPS  
Check this List of Symptoms and Suggested Steps To Take before requesting Service. You may be able to solve the problem yourself.  
If you face problems connecting the TV to external devices, please refer to the User Guide of the external device or call their service centers  
for help. Charges for TV installation and adjustments of customer controls are not covered under your warranty.  
SYMPTOMS  
SUGGESTED STEPS TO TAKE  
Can't get external 1. SPDIF output audio only in digital mode and the audio equipment used must have the decoder.  
audio equipment  
Hookup  
to work with TV.  
2. Ensure that Monitor Out Audio LR output audio is connected to Audio In of device (refer to  
Connection Guide Panel 3).  
Can't get the AV  
Press the AV button on the remote control repeatedly to select the desired AV channels. Note:  
Installation  
Installation  
channels on the TV SVHS can only be selected if a S-VHS device is connected and powered on.  
screen.  
TV displays wrong  
channel or no  
channels above 13  
Go to TUNER MODE in the television menu and select the correct signal source, then perform the  
automatic installation again. (Refer to page 11).  
Channel numbers  
do not follow the  
channel number  
of the  
Installation  
Go to TUNER MODE in the television menu and select the correct signal source, then perform the  
automatic installation again. (Refer to page 11).  
programs.  
Channel numbers  
look different. Eg.  
23-1, 45-3 etc.  
Installation  
Installation  
Installation  
You are in Digital Mode. Press A/D button on the remote control to toggle between Digital and  
Analog mode.  
Auto installation is Auto installation may take 20 to 40 minutes depending on the number of channels that are available.  
taking too long.  
Cannot add or  
skip channels from  
favorite list. Error  
message "Favorite  
Channel list  
1. You may not have completed auto installation. Do an auto installation again (refer to page 9).  
2. You may have chosen the wrong TUNER MODE. Go to TUNER MODE in the TV menu  
and select the correct signal source, then perform the auto installation again  
page 11).  
(refer to  
is empty. You  
must Auto  
Install."  
Unable to  
change Autolock  
password.  
You can change the Autolock password via the feature menu (refer to page 21)  
AutoLock  
Close Captioning  
text does not  
appear.  
Close Captioning text takes a while to appear. If Close Captioning text still does not appear, press  
the CC button on the remote control again to switch to another Close Captioning channel (refer  
to page 27and 28).  
Close Caption  
Unable to switch  
to another audio  
language  
You can only select different audio languages when the program is broadcasted in different audio  
language (refer to page 17).  
Digital Audio  
Unable to change  
picture-format.  
Picture-format mode can only be activated when you are watching high-definition (HD) program.  
Press the INFO button on the remote control. If the Information Banner does not show  
lighted, you are not watching a HD program and therefore format control cannot be activated (refer  
to page 30)  
Format Control  
"No  
Information is broadcaster dependent. If the broadcaster does not provide any information. "No  
Information" will be displayed when the INFO or GUIDE button on the remote control is  
pressed (refer to page 31)  
Information  
Banner  
Information"  
appears on the TV  
screen.  
33  
TROUBLESHOOTING TIPS  
SYMPTOMS  
SUGGESTED STEPS TO TAKE  
Error messages  
appear on the  
screen of TV:  
Settings  
No Signal  
Check that the antenna / cable is connected properly and that you have selected the correct  
tuner mode (refer to page 11).  
No Program  
There could be temporarily no transmission on the selected channel. You may like to add these  
channels to the Weak Dig Sig. list. (refer to page 15). When transmission is resumed or when  
available, your TV will receive it.  
Audio Only  
The current channel has only audio transmission.  
Sound is not in  
Stereo.  
This could be due to any of the following reasons:  
Sound  
1. Not all transmitted broadcasts by the cable or broadcast stations are in STEREO. Try checking  
with several major network stations to be sure that the station you selected is in STEREO.  
2. When SAP is turned ON, the sound mode is automatically set to MONO.  
3. Sound mode is set to MONO. Set the sound mode to STEREO. (Refer to page 19).  
4. When using an AV input, the television will not display STEREO even though it is producing  
stereo sound.  
Disturbing sound  
(such as buzzing,  
clicking, cracking,  
It is normal to hear a disturbing sound (such as buzzing, clicking, cracking, humming, whistling, etc)  
from a distance less than 2 meters (6 feet) with the television sound muted.  
If problem occurs on one channel, you may have a signal problem. Please contact the cable provider  
Sound  
humming, whistling or local broadcaster regarding the specific channel.  
etc.)  
No power to the  
TV  
Check the TV power cord. Unplug the power cord from the TV, wait 10 seconds, then reinsert  
the plug into your wall outlet. Power On the TV again.  
General  
Plug the power cord directly to the wall socket and not via an extension cord.  
If you need to use an extension cord, check that the fuse on the AC power strip is not blown.  
TV is not  
responding to  
Remote Control  
Ensure the batteries are inserted into the remote control according to the illustration in the battery  
compartment. Refer to page 7.  
General  
General  
Reset the TV by disconnecting the power plug from the wall  
outlet for 10 seconds and then reconnecting it again.  
Check antenna connections. Are they properly secured to the TV ANT 75 ohm plug?  
No Picture on the  
TV screen  
Check the TUNER MODE control for the correct tuner setting.  
Try running the Auto Install feature to find all available channels (refer to page 9).  
Press the AV button on the remote control to make sure the correct signal source is selected  
(FRONT, AV1, AV2, Current Channel, etc.).  
Note: SVHS can only be selected if a S-VHS device is connected and powered on.  
TV Displays white Some DVD Discs are encoded with as much as 30% more video information to give the best  
General  
lines in letterbox  
when viewing a  
DVD disc  
possible picture quality. With the DVD Player in the 16:9 picture format, the playback of this  
type of disc with extra video information can produce a number of small white lines in the  
upper portion of the black letterbox area. With some of these discs, this problem is inherent  
and does not require a service call.  
34  
CLEANING AND CARE  
WARNING Concerning Stationary Images on the TV Screen:  
Placement of the TV  
Do not leave stationary or letterbox images on screen for  
extended periods of time. This can cause uneven picture-tube  
aging.  
• To avoid cabinet warping, cabinet color changes, and  
increased chance of set failure, do not place the TV where  
temperatures can become excessively hot; for example, in  
direct sunlight or near a heating appliance.  
Normal use of the TV should involve the showing of pictures  
that contain constantly moving and changing images that fill the  
screen. Be careful not to leave nonmoving images on screen  
for extended periods of time, or to display the same images  
on screen too frequently, because subtle ghost images can be  
left on the picture tubes. Sources of stationary images may be  
DVD disks, laser disks, video games, CD-i disks, videotapes,  
digital television boxes, broadcast channels, cable channels, sat-  
ellite channels, and others. Here are some examples of station-  
ary images (this is not an all-inclusive list; you may encounter  
others in your viewing):  
• Be sure to allow a free flow of air to and from the perfo-  
rated back cover of the set.  
Cleaning  
• To avoid possible shock hazard, be sure the TV is unplugged  
from the electrical outlet before cleaning.  
• Regularly dust the TV with a dry, nonscratching duster to  
keep the TV clean.  
• When cleaning the TV, take care not to scratch or damage  
the screen surface. Avoid wearing jewelry or using anything  
abrasive. Do not use household cleaners. Wipe the front  
screen with a clean cloth dampened with water. Use even,  
easy, vertical strokes when cleaning.  
• DVD menus—listings of DVD disk content  
• Letterbox black bars—shown at the top and bottom of the  
TV screen when a wide screen (16:9) movie is viewed on a  
TV with standard (4:3) aspect ratio.  
• Gently wipe the cabinet surfaces with a clean cloth or  
sponge dampened in a solution of cool, clear water and a  
mild soap or detergent. Use a clean, dry cloth to dry the  
wiped surfaces.  
• Video-game images and scoreboards  
• Television station logos—present a problem if they are  
bright and stationary; moving or low-contrast graphics are  
less likely to cause uneven aging of the picture tube  
• Occasionally vacuum the ventilation holes or slots in the  
back cover of the set.  
• Stock-market tickers—presented at the bottom of the TV  
screen  
• Never use thinners, insecticide sprays, or other chemicals on  
or near the cabinet, as they might cause permanent damage  
of the cabinet finish.  
• Shopping channel logos and pricing displays—bright and  
shown constantly or repeatedly in the same location on the  
TV screen.  
35  
SPECIFICATIONS  
27PT9015D  
32PT9005D  
32PT7005D  
PICTURE / DISPLAY  
Aspect ratio :  
4:3  
4:3  
4:3  
Picture Display  
Picture Enhancement  
27" Real Flat Picture,  
32" Real Flat Picture,  
32" Black Matrix  
Picture tube,  
Scavem, Auto Picture (5 2D Comb filter,  
modes)  
Scavem, Auto Picture Auto Picture  
(5 modes)  
(5 modes)  
Color, Contrast,  
Color, Contrast,  
Color, Contrast,  
Sharpness Control  
Sharpness Control  
Sharpness Control  
SOUND  
2 x 5w  
Incredible Surround  
Sound Power (Output RMS)  
Sound Enhancement  
CONVENIENCE  
Auto Program  
Easy toggle Digital / Analog modes  
Closed Captioning Full text  
Sleeptimer  
Clock  
ON SCREEN DISPLAY  
LANGUAGES  
English, French, Spanish  
CONNECTIVITY  
Rear  
Component Video Input (Y Pb Pr)  
S-Video (SVHS)  
Composite Video input (CVBS)  
Antenna / Cable RF In  
SPDIF Out (Digital Only)  
Audio Out (Cinch)  
Composite Video Input (CVBS)  
Headphone Jack  
Side  
USA  
USA  
MEXICO  
USA  
ELECTRICAL INFORMATION  
Voltage (V)  
127V~  
60Hz  
120V~  
60Hz  
120V~  
60Hz  
120V~  
60Hz  
Frequency (Hz)  
Approx. consumption (W)  
Max. consumption (W)  
134W  
147W  
127W  
139W  
120W  
132W  
125W  
137W  
WEIGHT & DIMENSIONS :  
49 kg / 108 lbs  
44 kg / 97 lbs  
60 kg / 132 lbs  
55 kg / 121 lbs  
Weight (incl. Packaging) :  
Weight (excl. Packaging) :  
76 kg / 167 lbs  
71 kg / 156 lbs  
27 inch / 68.6 cm  
32 inch / 81.3 cm  
Visible diagonal / screen size :  
32 inch / 81.3 cm  
Specifications and information are subject to change without notice.  
36  
PHILIPS LIMITED WARRANTY  
90 Days Labor & One (1) Year Parts & Two (2) Years Display  
PHILIPS CONSUMER ELECTRONICS warrants this prod- TO OBTAIN WARRANTY SERVICE IN THE U.S.A.,  
uct against defect in material or workmanship, subject to any con- PUERTO RICO, OR U.S. VIRGIN ISLANDS…  
ditions set forth as follows:  
Contact Philips Customer Care Center at:  
1-888-PHILIPS (1-888-744-5477)  
PROOF OF PURCHASE: You must have proof of the date  
of purchase to receive warranted repair on the product. A sales  
receipt or other document showing the product and the date  
that you purchased the product as well as the authorized retailer  
included, is considered such proof.  
TO OBTAIN WARRANTY SERVICE IN CANADA…  
1-800-661-6162 (French Speaking)  
1-888-PHILIPS (1-888-744-5477) - (English or Spanish  
Speaking)  
COVERAGE:  
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS  
WARRANTY IS THE EXCLUSIVE REMEDY FOR THE  
CONSUMER. PHILIPS SHALL NOT BE LIABLE FOR ANY  
INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR  
BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON  
THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED  
BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF  
MERCHANTABILITY OR FITNESS FOR A PARTICULAR  
PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO  
THE DURATION OF THIS WARRANTY.  
(If the product is determined to be defective)  
LABOR: For a period of ninety (90) days from the date of pur-  
chase, Philips will repair or replace the product, at its option, at  
no charge, or pay the labor charges to any Philips authorized  
repair facility. After the period of ninety (90) days, Philips will no  
longer be responsible for charges incurred.  
PARTS: For a period of one (1) year from the date of purchase,  
Philips will supply at no charge, new or rebuilt replacement parts  
in exchange for defective parts. Philips authorized service centers  
will provide removal and installation of the part under the speci-  
fied labor warranty.  
Some states do not allow the exclusions or limitation of incidental  
or consequential damages, or allow limitations on how long an  
implied warranty lasts, so the above limitations or exclusions may  
not apply to you. In addition, if you enter into a service contract  
agreement with the PHILIPS partnership within ninety (90) days of  
the date of sale, the limitation on how long an implied warranty  
DISPLAY: For a period of two (2) years from the date of pur-  
chase, Philips will supply, at no charge, a new or rebuilt active  
display device in exchange for the defective display. Philips author- lasts does not apply.  
ized service centers will provide removal and installation of the  
parts under the specified labor warranty.  
EXCLUDED FROM WARRANTY COVERAGE  
Your warranty does not cover:  
• Labor charges for installation or setup of the product, adjust-  
ment of customer controls on the product, and installation or  
repair of antenna systems outside of the product.  
• Product repair and/or part replacement because of improper  
installation, connections to improper voltage supply, abuse,  
neglect, misuse, accident, unauthorized repair or other cause  
not within the control of Philips.  
• A product that requires modification or adaptation to enable  
it to operate in any country other than the country for which  
it was designed, manufactured, approved and/or authorized, or  
repair of products damaged by these modifications.  
• Damage occurring to product during shipping when improperly  
packaged or cost associated with packaging.  
• Product lost in shipment and no signature verification of receipt  
can be provided.  
• A product used for commercial or institutional purposes  
(including but not limited to rental purposes).  
• Products sold AS IS or RENEWED.  
This warranty gives you specific legal rights. You may have other rights which vary from state/province to state/province.  
Philips, P.O. Box 671539, Marietta, GA. 30006-0026  
(Warranty: 4835 710 27400)  
37  
INDEX  
Accessories List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
Information Banner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
Language Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Picture Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Quick Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Registration of TV Information . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
Safety / Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3  
Second Audio Programming (SAP) . . . . . . . . . . . . . . . . . . . . . 19  
Sharpness Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Sleeptimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
Stereo/Mono Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Timer Controls  
Active Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
AutoLock Controls  
Access Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Block/Clear All Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
Movie Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
TV Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
Blocking Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
Automatic Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Auto Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Auto Sound. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
AVL (Automatic Volume Leveler) Control. . . . . . . . . . . . . . . 19  
Balance Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Bass Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Brightness Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
Activate Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Clock, Time Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Display Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Channel Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Start Time Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Stop Time Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Tint Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Treble Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33-34  
Tuner Mode Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Warranty (Limited). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
Weak Digital Signal (Add or Skip) . . . . . . . . . . . . . . . . . . . . . . 15  
Channel Edit (Add or Skip channels) .. . . . . . . . . . . . . . . .  
12  
Closed Captioning in Digital Mode . . . . . . . . . . . . . . . . . . . . .27  
Closed Captioning in Analog Mode. . . . . . . . . . . . . . . . . . . . .28  
Color Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Color Temperature (Color Temp) Control . . . . . . . . . . . . . . 18  
Electronic Program Guide (EPG). . . . . . . . . . . . . . . . . . . . . . . 31  
Feature Highlights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Format Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32  
Guide To Digital TV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
38  
Specifications are subject to change without notice.  
Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners.  
2005 © Koninklijke Philips Electronics N.V. All rights reserved.  
3139 125 35342  
39  

IBM E54 User Manual
JVC AV 21L24 User Manual
JVC AV 36F802 AV 36F702 AV 32F802 AV 32F702 AV 27F802 AV 27F702 User Manual
JVC DR MH300SEK User Manual
JVC GD V4200PZW G User Manual
Kuppersbusch USA GKS 6740 0 M UL User Manual
LG Electronics E1910T User Manual
New Transducers TR 5001 User Manual
Philips 150B5CS User Manual
Philips Computer Monitor 190S8 User Manual