Philips 25HT User Manual

21HT  
25HT  
29HT  
Instruction for Use  
p1-7  
1
2/4/05, 1:40 PM  
SAFETY INFORMATION AND USEFULT IPS  
SAFETY INFORMATION  
Disconnect mains plug when :  
the red light below theTV screen is flashing continuously.  
a bright white line is displayed across the screen.  
cleaning theTV screen. Never use abrasive cleaning agents. Use a slightly damp chamois  
leather or soft cloth.  
there is a lightning storm.  
the set is left unattended for a prolonged period of time.  
No naked flame sources, such as lighted candles, should be placed on top of theTV or in the  
vicinity.  
Do not place yourTV set under direct sunlight or heat.  
Leave at least 5 cm around each side of TV set for ventilation to avoid over-heating.  
Avoid placing your set where it is likely to be exposed to rain or water (e.g. near the  
window).  
No objects filled with liquids should be placed on top theTV so as to avoid dripping or  
splashing of liquids on the set.  
USEFUL TIPS  
Do not leave your set on standby mode for a prolonged period of time. Switch off set to  
allow it to be demagnetised. A demagnetised set supports good picture quality.  
Do not shift or move the set around when it is switched on. Uneveness in colour in some  
parts of the screen may occur.  
Never attempt to repair a defectiveTV yourself. Always consult a skilled service personnel.  
3
p1-7  
3
2/4/05, 12:28 PM  
BEFORE CALLING SERVICE  
Below is a list of frequently occurred symptoms. Before you call for service, make these simple  
checks. Some of these symptoms can easily be rectified if you know what to do.  
Symptom  
What you should do  
Colour patch  
(uneveness)  
Switch off theTV by the mains power button. Wait for 20  
minutes before switching on again.  
Check theTV is not placed too near speakers or magnetic  
objects.  
No power  
No picture  
Check theTV’s AC power cord is plugged into the mains  
socket. If there is still no power, disconnect plug. Wait for 60  
seconds and re-insert plug. Switch on theTV again.  
Check the antenna connection at the rear of theTV.  
PossibleTV station problem. Try another channel.  
Good picture  
but no sound  
Try increasing the volume.  
Check that the sound is not muted. If it is muted, press the  
Mute button on the remote control to restore sound.  
Good sound but poor  
colour or no picture  
Try increasing the contrast and brightness setting.  
Check antenna connection at the rear of theTV.  
Snowish picture and  
noise  
Horizontal dotted lines  
Possible electrical interference e.g. hairdryer, vacuum  
cleaner, etc. Switch off appliances.  
Double images or  
“Ghost” images  
Possible poor positioning of antenna. Using a highly directional  
antenna may improve reception.  
TV not responding to  
remote control handset  
Check life span of batteries of remote control handset.  
Aim remote control handset directly at remote control sensor  
lens on theTV.  
4
p1-7  
4
2/4/05, 12:28 PM  
HOOKING UP YOURTV (BASIC CONNECTION)  
ANTENNA CONNECTION  
Connect the aerial plug to the antenna socket ¬  
on the backcover.  
MAINS CONNECTION  
For correct mains voltage, refer to type sticker at  
the rear of theTV set.  
Consult your dealer if mains supply is different.  
SWITCHING ON THE SET  
Press the main power button to switch on/off  
theTV.  
If the set is on standby (indicator is red), press the  
Power button on the remote control to switch on  
the set.  
USE/CARE OF REMOTE CONTROL  
To load the supplied batteries into the remote control :  
Remove the battery compartment lid at the back of  
the remote control.  
Insert the correct type of batteries into the  
compartment.  
Ensure the (+) and (–) ends of the batteries are  
placed in the right position.  
Reattach the battery compartment lid.  
Note  
Always remove the batteries from the remote control handset if handset is not used for a long  
period.This can help prevent damage to handset from possible battery leakage.  
5
p1-7  
5
2/4/05, 12:28 PM  
BACK CONNECTORS  
*WARNING - RISK OF ELECTRIC SHOCK. DO NOT REMOVE THIS COVER.  
- DO NOT CONNECT TELEPHONE CABLE TO SMART PLUG (RJ12) CONNECTOR.  
Smart Card slot  
Monitor Component Video Input  
Out  
Y
Note:  
1. Do not connectVideo In and S-Video  
Ext Spk  
Video In  
concurrently.  
2. When a Smart Card with Audio/Video and  
S-Video inputs are installed into the Smart Card  
slot, the inputs on the Smart Card cannot be  
connected concurrently with theVideo In or  
S-Video and Audio L/R In of theTV set or vise  
versa. In this case, you can only use either the  
inputs on the Smart Card orTV set.  
Audio  
L
Pb  
Pr  
L
S-video  
RJ 12  
R
R
For “Y” models  
Monitor Component Video Input  
Out  
Y
Ext Spk  
Video In  
Audio  
L
Pb  
Pr  
L
S-video  
RJ 12  
R
R
Note:  
Do not connectVideo In and S-Video concurrently.  
For “R” models  
Monitor AV1  
Out  
in  
VIDEO  
L/Mono  
Audio  
R
For “Z” models  
6
p1-7  
6
2/4/05, 12:28 PM  
REMOTE CONTROLS  
Three types of remote controls could be used for setup purpose:  
POWER  
RECALL  
CC  
TEXT  
SMART SLEEP  
b
`
GUEST  
DCM  
1
2
3
6
9
SETUP  
4
5
8
7
GUIDE  
RESET  
CH  
0
M
A/CH  
+ Ñ  
Ñ-  
VOL  
CH  
H
A
B
C
D
G
E
F
CLOCK  
A/V  
RC2886  
(RC19335018/01)  
RC2887  
(RC19335025/01)  
RC2573GR  
(optional)  
For the purpose of explanation,RC2886/RC2887 is used.Remote control RC2573GR is optional  
and can be purchased separately. Refer to its accompanying guide “RC2573GR Remote Control  
Instructions” for details of its operation.  
7
p1-7  
7
2/4/05, 3:42 PM  
ACTIVATING TV SETUP MENU  
WITH REMOTE CONTROL RC2886/RC2887  
(only when SECURITY in theTV SETUP menu is set to LOW).  
To activateTV Setup menu.  
Select a channel number.  
Key in 3 1 9 7 5 3.  
Press  
.
H
The above sequence should be done within 20 seconds and TV SETUP menu will appear.  
WITH REMOTE CONTROL RC2573GR  
(only inTV Commercial mode)  
Part A: To checkTV’s mode.  
Set the remote control selectable switch to SETUP.  
Press RECALL key and theTV Status menu will appear.  
Check line 10 of the menu to see if theTV is in the Commercial or Consumer  
mode.  
If theTV is in the Commercial mode, then proceed to Part B to activate theTV  
Setup menu. Otherwise, go to Part C to change theTV mode to Commercial.  
Part B: To activateTV Setup menu.  
Press the RECALL key to clear the menu.  
Press the M key to activate theTV Setup menu.  
Part C: To select Commercial mode, if theTV is in Consumer mode (or to select  
Consumer mode, if theTV is in Commercial mode).  
Press the RECALL key to clear the menu.  
Press 0 2 4 9 9 5.  
Press M key and theTV Mode menu appears.  
Press +or -key to select Commercial mode.  
Highlight STORE and press theÉkey to store the change. TV will then go to  
standby mode.  
Press any numeric key to switch on theTV again and follow the procedure in  
Part B, step 2 to activate theTV Setup menu.  
8
p8-12  
8
2/4/05, 1:40 PM  
TV SETUP MAIN MENU  
Below shows the structure of the menu items  
TV SETUP  
* LANGUAGE  
ENGLISH  
NO. OF CHANNELS  
* INSTALLATION  
* CLOCK SETUP  
* BRIGHTNESS  
* COLOUR  
É
É
É
30  
33  
49  
58  
49  
0
|||||||  
|||||||  
||||||  
|||||||  
||||  
* CONTRAST  
|||||||||  
||  
* SHARPNESS  
* TINT  
|||||||||||  
(only for NTSC signal)  
(only for 29HT model)  
(only for 29HT model)  
||||  
|||||||||  
||||||| |||||||  
* ROTATION  
|
* SCAVEM  
YES  
0
||||||| |||||||  
HS OFFSET  
|
||||||| |||||||  
VSH OFFSET  
|
0
0
||||||| |||||||  
VA OFFSET  
|
(only for stereo models)  
* FORCED MONO  
* BALANCE  
NO  
0
||||||| |||||||  
|
||  
* TREBLE  
|||||||||||  
58  
49  
||||  
* BASS  
|||||||||  
* AVL  
NO  
||||||||  
AUDIO OUT VOLUME  
* SPATIAL  
||||||  
31  
YES  
YES  
STEREO  
OFF  
NO  
* ULTRA BASS  
* AUDIO I/II  
* SLEEPTIMER  
VOLUME FIXED  
VOLUME BAR  
YES  
||||||||||  
MIN VOLUME  
MAX VOLUME  
|
0
|||||||  
|||||||  
|||||||  
33  
33  
15  
|||||||  
SWITCH ON VOLUME  
* BUZZER VOLUME  
SWITCH ON CHANNEL  
POWER ON  
|||||||||||  
||||  
TV 1  
STANDARD  
OFF  
NO  
* LNA  
STEP TUNING  
DIGIT TIMEOUT  
BLANKING TIME  
CHANNEL DISPLAY  
KEYBOARD LOCK  
FREE PROTECTED  
ESP  
3.0SEC  
960MS  
ALL  
NO  
NO  
10HR  
NO  
INTERFACE  
AUDIO/VIDEO MUTE  
* AUDIO/VIDEO OUT MUTE  
MONITOR OUT RF  
WELCOME MESSAGE  
CHANNEL GUIDE  
REMINDER  
OFF  
NO  
NO  
É
NO  
NO  
TELETEXT ACCESS  
SECURITY  
YES  
LOW  
Note: *denotes item which appears in both the Commercial and Consumer mode.  
Only 8 items will be displayed at one time.  
¸
1) To see more items, press the  
menu, highlight it with the  
(
¸
) key on the remote control. To alter any item on the  
(
)key and execute with the  
(
˝
) or  
(
) key.  
˙
˚
¸
2) To highlight any item in a menu, press either the  
coloured bar until it rest on the item.  
(
) or  
(
)key to move the  
˝
3) To select options or to execute an item in the menu, press the  
(
) or  
(
)key.  
˙
MENU  
4) To exit, press the  
key.  
9
p8-12  
9
2/4/05, 4:33 PM  
TV SETUP SUB-MENUS  
LANGUAGE  
When you first enter the TV SETUPmenu, LANGUAGEis highlighted. You may select  
˝
other languages available with the  
(
) or  
(
) key.  
˙
NO. OF CHANNELS  
Show the number of channels under each category type. Enter the TV SETUP menu and  
highlight NO.OF CHANNELS.  
TV SETUP  
LANGUAGE  
ENGLISH  
NO. OF CHANNELS  
INSTALLATION  
CLOCK SETUP  
BRIGHTNESS  
COLOUR  
CONTRAST  
SHARPNESS  
É
É
É
30  
33  
49  
58  
|||||||  
||||||  
|||||||  
|||||||  
||||  
|||||||||  
||  
|||||||||||  
˝
Note: Use the  
(
) or  
(
) key to select its sub menu.  
˙
NO. OF CHANNELS  
TV  
35  
5
5
5
É
PAYTV  
INFO  
RADIO  
STORE  
Highlight the item you wish to change. Edit with the digit keys. To store changes in the memory,  
highlight STOREand confirm with the ) key. The total number of channels cannot  
(
˙
exceed 125. After storing is completed, TV will go into standby mode.  
TV INSTALLATION (for countries other than Philippines)  
Highlight INSTALLATIONin the TV SETUPmenu and enter its sub menu with the  
˝
(
) or  
(
) key. Installation menu via local control is not available in Consumer/  
˙
Commercial modes.  
INSTALLATION  
+ INPUT  
COLOUR STANDARD  
FRONT END  
AUTO*  
AUTO*  
É
175 MHZÉ  
TV 1  
SOUND STANDARD  
AUTO STORE  
MANUAL SEARCH  
CHANNEL  
Note:  
STORE  
FINE TUNE  
É
+ only for  
commercial  
mode.  
* TV system  
dependant  
|||||||  
|||||||  
|
PROTECTION  
LABEL  
TELETEXT LANGUAGE  
VIDEO BLANK  
AUDIO MUTE  
NO  
É
W
NO  
NO  
10  
p8-12  
10  
2/4/05, 12:18 PM  
TV INSTALLATION MENU  
INPUT  
This menu item selects the input source to be assigned per channel. The selectable sources are  
FRONTEND, AV1, AV2, AV3, CVI, AV2YCor AV3YC(dependent on model). To select  
press the  
(
˝
) or  
(
) key.  
˙
COLOUR STANDARD/SOUND STANDARD (not available for single system TV)  
Selects the colour and sound system of transmission.  
AUTO STORE  
When this is activated, theTV will start at the lowest valid frequency to search for a signal.  
Highlight AUTO STOREand press the  
(
) key to start. The word SEARCHING  
˙
is displayed indicating that the process is in progress. When a valid station is found, the next  
available channel number is assigned to it. The word will disappear once the process is  
completed.  
MANUAL SEARCH  
This item could be used if you wish to search for signal station by station or if you wish to key in  
the frequency directly with the digit keys on the remote control. Highlight MANUAL SEARCH  
and press the  
(
) key to start searching. Once a station is found, theTV will stop  
˙
searching for you to proceed to the next item.  
CHANNEL  
Press the  
˝
(
) or  
(
) key to select the type of channel:-TV, PAYTV, INFO, CVI,  
˙
AV3YC or RADIO. Then key in the channel number with the digit keys. (Not applicable if AV3YC  
or CVI are selected)  
STORE  
Press the  
˝
(
) or  
(
) key to store any changes you have done.  
˙
Note: Each change in a channel needs to be stored individually.  
FINE TUNE  
Press the  
˝
(
) or  
(
) key to fine tune the displayed frequency.  
˙
PROTECTION  
Used to lock each channel individually. To lock, select YES. In normal operation, if user tries to  
access this channel, the picture and sound are muted. Teletext cannot be activated and the  
LOCKED” message will be displayed for 3 seconds.  
Note:To unlock protection for all channels at one time, go to FREE PROTECTEDin  
TV SETUPmenu and press the  
(
) key to execute.  
˙
LABEL  
Input a maximum of 8 characters for the channel’s label. Press the  
(
) key to start the  
˙
˝
first character input or to go to the next character and the  
(
) key to go to previous  
˚
¸
character. To input characters, press the  
(
) or  
(
) key to select from the list:-  
A to Z, 0 to 9, , –, •,/, :, =, ?, ;, <, >, @ or space. To edit, go into the character’s space and re-input.  
MENU  
To exit, press the  
key.  
11  
p8-12  
11  
2/4/05, 12:18 PM  
TELETEXT LANGUAGE  
This option allows toggling between differentTeletext languages. WforWestern English or A  
for Arabic. The default selection is W. For models withoutTeletext feature, selection of Wor A  
has no effect.  
VIDEO BLANK  
To blank out picture of the channel, select YES.  
AUDIO MUTE  
To switch off the sound of the channel, select YES.  
TV SETUP SUB-MENUS (CONTD)  
CLOCK SETUP  
To set time for display on the top right hand corner. Highlight CLOCK SETUP.  
TV SETUP  
LANGUAGE  
ENGLISH  
NO. OF CHANNELS  
INSTALLATION  
CLOCK SETUP  
BRIGHTNESS  
COLOUR  
É
É
É
30  
33  
49  
58  
|||||||  
||||||  
|||||||  
|||||||  
||||  
CONTRAST  
SHARPNESS  
|||||||||  
||  
|||||||||||  
Press the  
(
) key to enter clock setup menu.  
˙
Use digit keys to key in desired time, starting from hour then minutes. For single digit, key in 0  
follow by the digit.  
To display time, highlight DISPLAYand select YES.  
TV SETUP  
DISPLAY  
TIME SETTING  
TELETEXT TIME DOWNLOAD  
YES  
12:10  
NO  
CLOCK SETUP VIA T ELETEXT TIME DOWNLOAD (will only work for models with  
Teletext feature only)  
Alternatively, if there are channels broadcasting teletext, you could download the teletext time  
to your clock. In this way the displayed time will follow that of Teletext transmission.  
Highlight TELETEXT TIME DOWNLOADand select YES.  
TV SETUP  
DISPLAY  
TIME SETTING  
TELETEXT TIME DOWNLOAD  
YES  
00:00  
YES  
DOWNLOAD CHANNEL  
TIME OFFSET  
TV 5  
0
|||||||  
|||||||  
|
Highlight DOWNLOAD CHANNELand select a teletext transmission channel number with  
the digit keys. If there is a difference in the time zone from the teletext time, highlight TIME  
OFFSETand using the  
(
˝
) or  
(
) key enter the difference in time. To  
˙
MENU  
display the time, highlight DISPLAYand select YES. To exit,press the  
key.  
Note: The downloaded time will only take effect the next time you switch on theTV.  
12  
p8-12  
12  
2/4/05, 12:18 PM  
TV SETUP SUB-MENUS...CONTD  
BRIGHTNESS/COLOUR/CONTRAST/SHARPNESS/TINT  
Enter the TV SETUPmenu and highlight accordingly. Preset theTV by adjusting the  
brightness, colour, contrast, sharpness or tint (applicable for NTSC signal only) of the picture.  
MENU  
All these 5 items are also accessible to users via the  
key for personal settings.  
ROTATION (only for 29HT model)  
Adjust the tilt effect of the picture on screen.  
SCAVEM (only for 29HT model)  
ScanVelocity Modulation feature produces sharper and crispier picture. However, this feature  
may cause text display to be too sharp, hence more difficult to read.Thus, the option to select  
YESto activate the feature or NOto deactivate the feature is provided.  
HS/VSH/VA OFFSET  
HS (Horizontal Shift),VSH (Vertical Shift) andVA (Vertical Amplitude) Offset items are for the  
purpose of display orientation adjustment that may be needed for video signals generated by  
smart cards. However, depending on the specific smart card design for RGB insertion, the  
adjustment range for some parameters may be limited or in some cases, some parameters may  
have no effect at all. Press the  
(
˝
) or  
(
) key to adjust.  
˙
FORCED MONO (available in stereo sets only)  
Switch this on to force stereo mode to mono.  
BALANCE (for stereo signal)  
˝
Balances the sound output from theTV’s speakers. Use the  
(
) or  
(
) key to adjust.  
˙
TREBLE/BASS (for stereo signal)  
˝
Adjust the treble or bass of sound output. Use the  
(
) or  
(
) key to adjust.  
˙
AVL (AUTO VOLUME LEVELLER)  
This feature if switched on, will automatically adjust any sudden changes in theTV’s volume to a  
preset level.  
AUDIO OUT VOLUME  
Set the volume for the external audio output connector. Use the  
(
˝
) or  
(
)
˙
key to adjust.  
SPATIAL  
This option toggles theTV’s sound spatializer feature ONor OFF. If turned ON, theTV sound  
will have a surround-sound theatre effect.  
ULTRA BASS  
This option toggles the Ultra BASS feature ONor OFF. If turned ON, theTV sound will have  
stronger bass effects.  
13  
p13-19  
13  
2/4/05, 12:19 PM  
AUDIO I/II  
This menu item is to enable the switching from Stereo or Nicam Stereo to Mono, or to choose  
between Dual I or Dual II in case of bilingual transmission.When the sound mode is switched  
˝
to Mono, the indication is displayed in red. Press the  
the required audio mode.  
(
) or  
(
) key to select  
˙
SLEEP TIMER  
This menu item is to select an automatic period for theTV to switch to Standby when theTV  
does not receive any commands from the user.This is a useful feature for energy saving if hotel  
guests have left the room with theTV still in On mode.The available periods are 15 mins, 30  
mins, 45 mins, 60 mins, 90 mins, 120 mins, 180 mins, 240 mins and OFF. Press the  
) key to select the required period.  
(
˝
) or  
(
˙
VOLUME FIXED  
Sets a fixed volume level everytime theTV is switched on. The selections are:  
a) NO – volume level set in SWITCH ON VOLUMEin theTV Setup menu.  
b) YES – volume remain fixed at the SWITCH ON VOLUMElevel and cannot be  
adjusted.  
VOLUME BAR  
To display volume bar when adjusting volume, select YES. To hide bar, select NO.  
MIN VOLUME  
˝
Sets the limit for the minimum volume of theTV. Use the  
adjust.  
(
) or  
) or  
(
)key to  
) key to  
˙
MAX V OLUME  
Sets the limit for the maximum volume of theTV. Use the  
adjust.  
(
˝
(
˙
SWITCH ON VOLUME  
˝
Sets theTV’s switch on volume. Use the  
(
) or  
(
) key to adjust.  
˙
BUZZER VOLUME  
Sets the volume of theTV’s internal buzzer. The buzzer is used as part of theTV’s wake up  
alarm function (if activated)  
SWITCH ON CHANNEL  
˝
Sets theTV’s switch on channel. Use the  
(
) or  
(
) key to select the type of  
˙
channel. Key in the channel number with the digit keys. If STANDARDis selected, upon  
switching on, theTV will select the last viewed channel.  
14  
p13-19  
14  
2/4/05, 12:19 PM  
POWER ON  
Select STANDARD, STANDBYor FORCEDmode.The different modes are as explained below:  
STANDARD:TV will be automatically switched to the last status (STANBYor ON)  
whenever the mains power is turned ONor resumed after a power interruption.  
STANDBY:TV will be automatically switched to STANBY(even if the last status was ON)  
whenever the mains power is turned ONor resumed after a power interruption.  
FORCED:TV will be automatically switched to ONwhenever the mains power is turned ON  
or resumed after a power interruption. Note that the remote control STANDBYkey will no  
longer function whenTV is set to this mode.  
LNA (LOW NOISE AMPLIFIER)  
Select OFF, ONor AUTO. If ONis selected, the LNA feature in theTV set will always be  
applied to incoming signals. If set to AUTO, theTV set will first analyze incoming signals and  
apply the LNA feature if necessary. By default, the LNA setting is OFF.  
STEP TUNING  
For calling up or changing channels. When this feature is switched YES, theTV will respond  
immediately to the change of channel upon keying in the first digit. If this feature is switched  
NO, one has to either wait for a few seconds after keying in the first digit or complete keying in  
2 digits beforeTV changes channel.  
Note:When an external set-top box is connected to the RJ12 port for IR link, choose either  
YES/NOfor optimum channel switching performance.  
DIGIT TIMEOUT  
Selects the digit entry timeout period via digit key entry from 1.0 SEC to 9.9 SEC. This allows  
the response time between the 1st digit entry and the 2nd digit entry to be adjusted when  
2-digit entry is needed.  
BLANKING TIME  
Sets the blanking interval between the switching of channels. The recommended default setting  
is 900 to 960ms.  
CHANNEL DISPLAY  
Selects the ways of displaying the information for a channel. The options are: ALL(display the  
number and label of a channel), NONE(do not display any information), NUMBER(display  
only the number of a channel) and LABEL(display only the label of a channel).  
KEYBOARD LOCK  
To lockTV control keys, select YES. To unlock, select NO.  
FREE PROTECTED  
Remove PROTECTIONfeatures for all channels set under TV SETUPmenu. All channels  
are not protected when select YES.  
ESP (ENERGY SAVING PROGRAMMABLE)  
This feature selects a time when theTV will automatically turn off. TheTV must remain on  
continuously during the period of time you select. If the power is switched off, the ESP timer will  
be re-initialised. Highlight ESP, then key in the required time with the digit keys. Select 0 if you do  
not wish to use this feature. If sleeptimer is selected, it would have priority over ESP time.  
15  
p13-19  
15  
2/4/05, 12:19 PM  
INTERFACE  
Enables the communication of theTV with the DCM when YESis selected. This is specifically  
applicable to the Interactive SystemTV, providing the interactivity feature between a DCM card  
of the Service Provider and the dedicated SystemTV.  
AUDIO/VIDEO MUTE  
To blank the screen when no signal is received. Select OFF(no blanking), BLACK(blank the  
screen black) or BLUE(blank the screen blue).  
AUDIO/VIDEO OUT MUTE  
Disables all output from theTV to the external Audio andVideo output connectors if YESis  
selected.The default setting is NO.  
MONITOR OUT RF  
Select YESto switch all output from theTV to the external Audio/Video output connectors  
to the same as the input RFsignal. Select NOto switch all output from theTV to the external  
Audio/Video output connectors to the same source as what is displayed on theTV. The default  
setting is NO.  
WELCOME MESSAGE  
This item is used to create, edit or delete a welcoming message. You can input up to 2 lines,  
with a maximum of 20 characters (inclusive of space) per line. Highlight WELCOME  
MESSAGEin the TV SETUPmenu and enter its sub menu by pressing  
(
).  
˙
Note: During creating, editing or deleting a message, you may wish to move from LINE 1 to  
MENU  
LINE 2 or vice versa. Press the key  
proceed.  
to exit from the present line. Highlight the new line and  
MESSAGE  
DISPLAY  
OFF  
É
LINE 1  
LINE 2  
CLEAR  
É
É
TO CREATE MESSAGE WITH LINE 1:  
¸
Highlight LINE 1with the  
(
) key. Press the  
(
) key to begin. The cursor  
˙
˚
will appear in the first character position. To input characters, press the  
(
) or  
¸
(
) key to select from the list:- A to Z, 0 to 9, , –, •,/, :, =, ?, ;, <, >, @ or space. Press the  
˝
(
) key to go to the next character position or the  
(
) key to go to the  
˙
previous character position.  
TO EXIT LINE 1:  
MENU  
Press the  
key.  
16  
p13-19  
16  
2/4/05, 12:19 PM  
TO CREATE MESSAGE WITH LINE 2:  
¸
Highlight LINE 2with the  
(
) key. Press the  
(
) key to begin. The cursor  
˚
˙
will appear in the first character position. To input characters, press the  
(
) or  
¸
(
) key to select from the list:- A to Z, 0 to 9, , –, •,/, :, =, ?, ;, <, >, @ or space. Press  
the  
(
) key to go to the next character position or the  
(
˝
) key to go to the  
˙
previous character position.  
TO EXIT LINE 2:  
MENU  
Press the  
key.  
TO EDIT MESSAGE:  
Highlight the message line that you wish to delete. Press the  
(
) key to begin. Move  
˙
˚
¸
the cursor to the character position that you wish to edit. Press the  
(
) or  
(
)
MENU  
key to select a new character from the list. Exit with the  
key after you have finished.  
TO DELETE ENTIRE MESSAGE:  
˝
Highlight CLEARand press the  
(
) or  
(
) key.  
˙
TO SWITCH ON/OFF MESSAGE:  
Highlight DISPLAYand select YESto display message the next time theTV is switched on  
or NOto not display message.  
TO EXIT FROM MESSAGE MENU:  
MENU  
Press the  
key.  
CHINESE WELCOME MESSAGE  
This option is only available when the Language option is set to Chinese.This option allows a  
fixed welcome message in Chinese to be displayed with or without the English welcome  
˝
message. Highlight  
(
) and use the  
(
) or  
(
) key to turn On or Off  
˙
the Chinese welcome message.  
CHANNEL GUIDE  
Select YESto see list of channel that has been programmed. For users to see the list, press  
MENU  
the  
or  
key to enter user’s menu. Highlight CHANNEL GUIDEand press the  
(
˝
)
˚
¸
(
) key to enter it. Press the  
(
) or  
(
(
) key to select a channel.  
˙
˝
To enter the channel, press the  
(
) or  
) key.  
˙
REMINDER  
Select YESif a permanent display of the channel number and label on the top of the screen is  
desired.  
17  
p13-20  
17  
2/17/05, 6:04 PM  
TELETEXT ACCESS  
Select YESto enable theTeletext feature or NOto disable theTeletext feature. For models  
withoutTeletext feature, selection of YESor NOhas no effect.  
SECURITY  
Select HIGHand only remote control RC2573GR can be used to enterTV Setup menu.  
OTHER FEATURES  
ALARM  
The Alarm feature will require the time to be set correctly according to the CLOCK SETUP  
procedure in page 12.  
To set the alarm, press the  
key to enter the ALARMmenu as shown below. If the time has  
not been previously set, the “NOT AVAILABLE” message will appear on theTV screen.  
12:30  
ALARM  
ALARM TIME  
--:--  
ALARM STATUS  
OFF  
Use the remote control numeric keys to enter the desired ALARM TIME. Once the time has  
been entered,the ALARM STATUSwill change to ON. Any key on the remote control can be  
used to cut off the alarm buzzer.  
To deactivate the alarm, press the  
key on the remote control.  
LOW BATTERY CHECK  
OK  
Press the  
key for approximately 5 seconds. The following appears:  
SERVICE  
REMOTE BATTERY  
1
OK  
If battery is low, the word LOWwill appear in place of OK.  
It is an indication that you need to replace the batteries in the remote control.  
TELETEXT (for models withTeletext feature only)  
To enterTeletext mode, press the b key.  
Function  
Page up  
RC2886/RC2887 keys  
+
TV  
TV  
Page down  
-
Select a page  
Digit  
Direct access to a subject  
(
˝
) or  
(
)
˙
To selectTeletext subpage  
18  
p13-20  
18  
2/17/05, 1:01 PM  
This page is intentionally left blank  
p13-20  
19  
2/4/05, 3:21 PM  
3139 125 33061  
p13-20  
20  
2/4/05, 3:21 PM  

IBM Computer Hardware User Manual
Kenmore ELITE 790 323 User Manual
LG Electronics L2000C User Manual
LG Electronics LG Life Good Computer Monitor M197WA User Manual
NEC LCD4010 LCD4610 User Manual
NEC PD750006 User Manual
Philips 21PT4437 User Manual
Philips 241P4LRY User Manual
Philips Computer Monitor 249C4Q User Manual
Philips MWC1230F User Manual