Pelco PMCS15A User Manual

Installation/Operation  
PMCS15A, PMCS17A, and PMCS19A  
Super-High Resolution Color Monitors  
C1991M-C (9/04)  
Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com  
In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150  
International Customers: Tel +1 (559) 292-1981 or FAX +1 (559) 348-1120  
REGULATORY NOTICES  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  
(1) this device may not cause harmful interference, and (2) this device must accept any interference re-  
ceived, including interference that may cause undesired operation.  
RADIO AND TELEVISION INTERFERENCE  
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant  
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful  
interference in a residential installation. This equipment generates, uses, and can radiate radio fre-  
quency energy and, if not installed and used in accordance with the instructions, may cause harmful in-  
terference to radio communications. However there is no guarantee that the interference will not occur  
in a particular installation. If this equipment does cause harmful interference to radio or television recep-  
tion, which can be determined by turning the equipment off and on, the user is encouraged to try to cor-  
rect the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver  
is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve  
Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office,  
Washington D.C. 20402.  
Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment  
can void your authority to operate this equipment under Federal Communications Commission’s rules.  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  
DESCRIPTION  
The PMCS15A, PMCS17A, and PMCS19A are super-high resolution color monitors. All monitors have  
computer-grade picture tubes. The PMCS15A and PMCS17A produce horizontal resolution of 700 TV  
lines and PMCS19A produces 800 TV lines. Standard high resolution monitors produce only about 350  
TV lines.  
The monitors automatically detect the power supply input (90-260 VAC, 50/60 Hz).  
Models  
PMCS15A  
PMCS17A  
PMCS19A  
Super-high resolution color monitor, 15-inch (38.10 cm)  
Super-high resolution color monitor, 17-inch (43.18 cm)  
Super-high resolution color monitor, 19-inch (48.26 cm)  
Pelco Manual C1991M-C (9/04)  
[ 3 ]  
INSTALLATION  
The monitor may be placed on any flat surface (desk or table) or rack-mounted. To rack-mount the  
monitor follow the instructions supplied with the rack mount kit.  
Video and Power Connections  
1. Video Cable Connection (Refer to Table A for video coaxial cable requirements.)  
a. Connect the video cable to the BNC video input labeled V1 IN on the back panel of the monitor.  
If the installation requires a second video input, connect a video cable to the BNC video input la-  
beled V2 IN.  
b. Looping Operation Only - Connect a video cable to the BNC connector labeled V1 OUT. If the in-  
stallation requires a second video output, connect a video cable to the BNC video output labeled  
V2 OUT. Refer to Figures 2 and 3.  
2. Impedance Switch Setting  
a. Terminating Operation Only - Set the termination switch to 75position.  
b. Looping Operation Only - Set the impedance switch to the V1-HI and V2-HI positions. Refer to  
Figures 2 and 3.  
3. Plug the power cord (provided) into the AC INLET connection on the back panel. Plug the other end  
of the cord into a power receptacle.  
FRONT  
AU1  
AU2  
VOLUME  
SHARP  
BRIGHT  
CONT  
.
COLOR  
TINT  
VIDEO 1 VIDEO 2  
S-VIDEO  
BAC K  
V1-H  
I
75  
V1 IN  
V2 IN  
AU1 IN  
AU2 IN  
S-VIDEO IN  
Y/C-HI  
V2-H  
I
75  
75  
V1 OUT  
V2 OUT  
AU1 OUT  
AU2 OUT  
S-VIDEO OUT  
AC INLET  
Figure 1. Models PMCS15A, PMCS17A, and PMCS19A Color Monitors, Front and Back Panels  
[ 4 ] Pelco Manual C1991M-C (9/04)  
Table A. Video Coaxial Cable Requirements  
Cable Type*  
Maximum Distance  
RG59/U  
RG6/U  
750 ft (229 m)  
1,000 ft (305 m)  
1,500 ft (457 m)  
RG11/U  
* Minimum cable requirements:  
75 ohms impedance  
All-copper center conductor  
All-copper braided shield with 95% braid coverage  
V1-H  
V1-L  
V1 IN  
V2 IN  
AU1 IN  
AU2 IN  
S-VHS IN  
S-HI  
V2-H  
CAMERA  
CAMERA  
V2-L  
S-LO  
V1 OUT  
V2 OUT  
AU1 OU  
T
AU2 OUT  
S-VHS OU  
T
VCR  
VCR  
Figure 2. Looping Operation - One Monitor with External Video Equipment  
CAMERA  
V1-H  
V1-H  
V1-H  
V1-L  
V2-H  
V1-L  
V2-H  
V1-L  
V2-H  
V1 IN  
V2 IN  
AU1 IN  
AU2 IN  
S-VHS IN  
V1 IN  
V2 IN  
AU1 IN  
AU2 IN  
S-VHS IN  
V1 IN  
V2 IN  
AU1 IN  
AU2 IN  
S-VHS IN  
S-HI  
S-HI  
S-HI  
V2-L  
S-LO  
V2-L  
S-LO  
V2-L  
S-LO  
V1 OU  
T
V2 OUT  
AU1 OUT  
AU2 OUT  
V1 UT  
V2 OUT  
AU1 OUT  
AU2 OUT  
V1 OUT  
V2 OUT  
AU1 OUT  
AU2 OUT  
S-VHS OUT  
S-VHS OUT  
S-VHS OUT  
VCR  
Figure 3. Looping Operation - Maximum of Three Monitors with External Video Equipment  
Pelco Manual C1991M-C (9/04)  
[ 5 ]  
OPERATION  
1. Set the video format switch located on the front panel to one of the following settings:  
VIDEO1 - Composite video (NTSC/PAL) mode  
VIDEO2 - Composite video (NTSC/PAL) mode for two, video input operation  
S-VIDEO - S-VHS mode if the S-VHS input jack on the back of the monitor is used  
2. If required adjust the picture using the control knobs on the front panel.  
Front Panel Adjustments  
TINT  
Color phase adjustment. Turn clockwise to increase the greenish tones in the picture.  
Turn counterclockwise to increase the reddish tones in the picture.  
COLOR Color saturation level. Turn the control knob clockwise to increase the saturation level  
and counterclockwise to decrease the saturation level.  
CONT  
Contrast adjustment. Proper adjustment will allow maximum gradations between the  
darkest and lightest picture contrast. Turn the control clockwise to increase picture con-  
trast and counterclockwise to decrease contrast.  
BRIGHT Brightness display adjustment. Turn the control clockwise to increase brightness and  
counterclockwise to decrease brightness.  
SHARP Sharpness adjustment. Adjust control knob to obtain the clearest picture.  
VOLUME Audio adjustment. Turn the control clockwise to increase volume and counterclockwise  
to decrease volume.  
MAINTENANCE  
If the quality of the picture is poor and cannot be improved by making adjustments on the front control  
panel, inspect all system connections and cable runs.  
To reduce the risk of electrical shock, do not remove the cover or back of monitor. No user-serviceable  
parts are inside. Refer servicing to qualified personnel, or contact the Pelco Customer Service Depart-  
ment for assistance. Refer to the Warranty and Return Information section.  
[ 6 ] Pelco Manual C1991M-C (9/04)  
SPECIFICATIONS  
ELECTRICAL  
Input Voltage  
Power Consumption  
PMCS15A  
PMCS17A  
PMCS19A  
90-260 VAC, 50/60 Hz, autoranging  
70 watts  
95 watts  
Approximate 100 watts  
Horizontal Resolution  
PMCS15A  
PMCS17A  
700 TV lines  
700 TV lines  
800 TV lines  
PMCS19A  
Visual Picture Size  
PMCS15A  
PMCS17A  
PMCS19A  
Sweep Linearity  
Speaker Output  
14-inch diagonal  
16-inch diagonal  
18-inch diagonal  
10%  
1.0 watt (-3 dBV)  
GENERAL  
Input/Output  
Video  
2 BNC inputs: 75 ohms or Hi-Z  
2 looping outputs  
Audio  
2 RCA inputs, Hi-Z  
2 looping outputs  
1 input DIN  
S-Video  
1 looping output  
Steel cabinet  
Black with black bezel around screen  
Construction  
Finish  
Dimensions  
PMCS15A  
14.0 (W) x 12.9 (H) x 15.0 (D) inches  
(35.6 x 32.7 x 38.1 cm)  
PMCS17A  
PMCS19A  
16.0 (W) x 14.5 (H) x 16.0 (D) inches  
(40.6 x 36.9 x 40.6 cm)  
17.4 (W) x 16.4 (H) x 17.5 (D) inches  
(44.0 x 41.5 x 44.5 cm)  
Weight  
PMCS15A  
PMCS17A  
PMCS19A  
35 lb (15.8 kg)  
43 lb (19.5 kg)  
53 lb (24.0 kg)  
ENVIRONMENTAL  
Operating Temperature  
Humidity  
32° to 106°F (0° to 41°C)  
0% to 90% (noncondensing)  
This equipment contains electrical or electronic components that must be recycled  
properly to comply with Directive 2002/96/EC of the European Union regarding the  
disposal of waste electrical and electronic equipment (WEEE). Contact your local  
dealer for procedures for recycling this equipment.  
(Design and product specifications subject to change without notice.)  
Pelco Manual C1991M-C (9/04)  
[ 7 ]  
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of  
shipment.  
Exceptions to this warranty are as noted below:  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and  
MC3651H-2X camera models, which have a five-year warranty.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, including when used in continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).  
Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and EnduraSeries distributed network-based video  
products.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight  
prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this  
warranty.  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s  
liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products  
shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential  
damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state  
to state.  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and  
provide the following information:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written  
explanation with the product when returned.  
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization  
number (CA number if returned for credit, and RA number if returned for repair).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate  
address below.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the  
following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco  
Pelco c/o Expeditors  
473 Eccles Avenue  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.  
Endura and ExSite are trademarks of Pelco.  
© Copyright 2004, Pelco. All rights reserved.  
REVISION HISTORY  
Manual #  
C1991M  
C1991M-A  
C1991M-B  
C1991M-C  
Date  
11/00  
01/01  
2/01  
Comments  
Original version.  
Added ETL and cETL certifications.  
Added information on model PMCS19A.  
Added information on model PMCS15A. Deleted model PMCS14A. Revised unit weights.  
9/04  

Intel IQ80333 User Manual
JVC C T2021 User Manual
JVC InteriArt AV 28X37HIE User Manual
LG Electronics L226WTP User Manual
NEC 42PD2 50PD1 User Manual
Philips 25PT7206 User Manual
Philips 29PT2204 User Manual
Philips KX TGA510M User Manual
Philips MAGNAVOX PR1913X1 User Manual
Philips MCD716 User Manual