Single Monitor Station
Installation and Operation Guide
Model No.
VL-GM201A
Thank you for purchasing a Panasonic Single Monitor Station.
Please read this Installation and Operation Guide before using the unit and save for future
reference.
Important Information
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrow
head within a triangle is
intended to tell the user that
parts inside the product are a
risk of electric shock to persons.
The exclamation point within a
triangle is intended to tell the
user that important operating
and servicing instructions are in
the papers with the appliance.
Important safety instructions
1) Read these instructions.
All the safety and operating instructions should be read before the appliance is operated.
2) Keep these instructions.
The safety and operating instructions should be retained for future reference.
3) Heed all warnings.
All warnings on the appliance and in the operating instructions should be adhered to.
4) Follow all instructions.
All operating and use instructions should be followed.
5) Do not use this apparatus near water.
For example, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet basement,
or near a swimming pool, and the like.
6) Clean only with dry cloth.
Do not use liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning.
7) Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions.
Slots and Openings in the cabinet are provided for ventilation and to ensure reliable
operation of the product and to protect it from overheating. The openings should never be
blocked by placing the product on a bed, sofa, rug, or other similar surface.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
This product should not be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s instructions have been
adhered to.
9) Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A grounding type plug has
two blades and a third grounding prong. The wide blade or the third prong are provided for
your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10)Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments / accessories specified by the manufacturer.
3
Important Information
12)Unplug this apparatus during lightning storms or when unused for long periods of time.
This will prevent damage to the product due to lightning and power-line surges.
13)Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power- supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
SAVE THESE INSTRUCTIONS
Additional safety information
1. Use only the power source marked on the unit. If you are not sure of the type of power
supplied to your home, consult your dealer or local power company.
2. Use only the specified AC adaptor.
3. Do not tamper with the plug.
4. Make sure the plug is securely inserted.
5. Do not touch the plug with wet hands.
6. Do not place objects on the power cord. Install the unit where no one can step or trip on
the cord.
7. To reduce the risk of electric shock, do not disassemble this unit. Take the unit to an
authorized service center when service is required. Opening or removing covers may
expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric
shock when the unit is subsequently used.
8. Unplug this unit from power outlets and refer servicing to an authorized service center
when the following conditions occur:
A. If smoke rises, or an unaccustomed noise or smell is discharged from the unit.
B. If metal objects have been dropped inside the monitor station.
9. Do not put your ear(s) near the speaker, as loud sounds emitted from the speaker may
cause hearing impairment.
10. Only a qualified technician is allowed to connect a power cable to the unit.
Contact an authorized service center.
11. Do not make any wiring connections when the power supply is turned on.
12. Never install wiring during a lightning storm.
13. Do not connect a power cable other than the specified voltage.
14. Do not connect the power cable to any terminal other than the one specified.
15. When existing chime wires are used, it is possible that they contain AC voltage. Electric
shock or unit damage could result. Contact an authorized service center.
16. Never touch the inside of the monitor station. High voltage is present.
17. Make certain when mounting the unit to any wall surface that the method used will hold the
weight of the unit properly.
18. If the wiring is outdoors, use a protection tube or a surge protector.
19. If the wiring is underground, do not make any connections underground.
20. WARNING – To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This
Apparatus To Rain Or Moisture.
4
Important Information
21. WARNING – Unplug this unit from power outlets if it emits smoke, an abnormal smell or
makes unusual noise. These conditions can cause fire or electric shock. Confirm that
smoke has stopped and contact an authorized service center.
Note:
L This product has a fluorescent lamp that contains a small amount of mercury. It also
contains lead in some components. Disposal of these materials may be regulated in your
community due to environmental considerations. For disposal or recycling information
please contact your local authorities, or the Electronics Industries Alliance:
<http://www.eiae.org.>
For best performance
L If a power failure occurs, the unit will not function.
L Do not place any objects within 20 cm (8 inches) of the monitor station. This may cause
communication errors or malfunction.
20 cm
(8 inches)
20 cm
(8 inches)
20 cm
(8 inches)
20 cm
(8 inches)
5
Introduction and Installation
Included items
1
2
3
6
4
7
5
No. Item
Quantity Notes
1
2
3
Monitor station
1
------
Mounting bracket
Wood screws
1
2
Attached to rear of the monitor station.
For the monitor station.
(4 mm x 16 mm, /16" x /8")
------
3
5
4
5
6
Power cable
AC adaptor
Wood screws
1
1
2
Enclosed in the AC adaptor case.
For the AC adaptor case.
(4 mm x 16 mm, /16" x /8")
3
5
7
Power cord
1
------
6
Introduction and Installation
Optional item information
Available optional items
*1
– Door station (VL-GC001A, VL-GC002A)
– Desktop stand (VL-GT001A)
*1 The door station figures shown in this installation and operation guide are based on a VL-
GC001A.
Compatible PBXs
*1
This unit is compatible with the following Panasonic PBXs :
– KX-TA308
– KX-TA624
– KX-TA824
– KX-TA1232
– KX-TAW848 (From Ver2.0)
– KX-TD308
– KX-TD816
– KX-TD1232
– KX-TDA50 (From Ver2.0)
– KX-TDA100 (From Ver2.01)
– KX-TDA200 (From Ver2.01)
*1 As of March, 2005. Consult your dealer for a current list of compatible PBXs.
7
Introduction and Installation
Location of controls
Front view
Side view
A B
C
RINGER
VOLUME
RINGER
HIGH
OR
MONIT
VOLUME
LOW
OFF
HIGH
LOW
OFF
I
J
BRIGHT
DOOR
D
E
AN
S
W
AUT
E
R
O
PUSH
HOLD
ANSWER
AUTO
PUSH
HOLD
F
ALK
T
H
G
Rear view
PBX MODE
OFF ON
K
8
Introduction and Installation
A Microphone
B Display
C MONITOR button
L Allows you to monitor the sound and camera image from the door station (page 26).
D BRIGHT button
L Allows you to adjust the display brightness. 5 levels are available.
E DOOR button
L Allows you to open the door (page 27).
F Speaker
G TALK button
L To answer a door call and/or speak to the visitor (page 23).
H Talk indicator
L Lights while you are talking.
I RINGER VOLUME switch
L To adjust the ringer volume. 3 levels (high/low/off) are available.
J ANSWER switch
L To change the answering mode (page 23).
K PBX MODE switch
L To connect the unit to a PBX, turn on this switch (page 20).
9
Introduction and Installation
Before installation
To avoid a malfunction or communication disturbance, do not install the monitor station in the
following locations:
– Places where vibration or any other kind of impact occurs.
– Places where echoing is frequent.
– Places where a high concentration of dust, hydrogen sulfide, phosphorus, ammonia, sulfur,
carbon, acid, or noxious fumes occur.
– Within 2 m (6'7") of a TV, microwave, personal computer, air conditioner or any other
electrical device.
Standard installation position of the monitor station
Place the monitor station in a location so that your eyes are the same height as the center of
the display.
Note:
L In areas surrounded by high electrical field, disturbance may occur in the monitor station’s
image or sound.
L Be sure to install the monitor station more than 5 m (16'5") away from the door station.
L Do not place any objects within 20 cm (8 inches) of the monitor station. This may cause
communication errors or malfunction.
L Do not install the monitor station inside a wall.
10
Introduction and Installation
Wiring schematic diagram
Door station
Terminal box
(4-conductor wiring)
D1 D2
PBX
(Example: KX-TDA50)
(Non polar)
Monitor station
D1
D2
P1
P2
S1
S2
(Non polar)
(Non polar)
Door opener
Power cable
AC adaptor
Power cord
Note:
L This door opener wiring schematic diagram is only an example. Refer to the wiring
instructions provided with your door opener and PBX for details.
L Refer to the technical data on page 30 when connecting to a door opener.
Power cable/wire type and distance
L Power cable (between the monitor station and the AC adaptor):
Type: Ф1.2 Fire alarm cable 16 AWG
Distance: Maximum 30 m (about 98 feet)
L Wire (between the monitor station and the door station):
Type: General cable CAT-3 24 AWG
Distance: Maximum 100 m (about 328 feet)
Loop resistance: 18.4 Ω or lower
L Wire (between the monitor station and PBX):
Type: General cable CAT-3 24 AWG
Distance: Maximum 100 m (about 328 feet)
11
Introduction and Installation
Installing the monitor station
Note:
L When connecting to a PBX, make sure the {PBX MODE} switch is set to {ON} before
installing the monitor station (page 20).
1 Install the mounting bracket to a wall using the wood screws (4 mm x 16 mm,
3
5
/16" x /8").
L Remove the mounting bracket from the rear of the monitor station beforehand.
L Before drilling, see page 10 for installation location.
Mounting bracket
83.5 mm
(35/16")
Wood screws
Wall
2 Attach the power cable to the terminal. See page 18 for details on how to attach the power
cable.
L If you want to use your own power cable, see page 11 for the type and distance.
Terminal (Non polar)
Power cable
12
Introduction and Installation
3 Attach the wires that connect to the door station to the terminal. See page 18 for details
on how to attach the wires.
L See page 11 for the wire type and distance.
L See the wiring schematic diagram on page 11.
Stripped end of the wire
9 mm
(3/8")
Terminal
(Non polar)
Button
Wire (Not included)
L If you want to connect the wires and the power cable without them going through a hole
in the wall behind the mounting bracket, connect by passing the wires through the wire
guide, and the power cable through the power cable guide.
Power cable guide
Wire guide
13
Introduction and Installation
4 Mount the monitor station to the mounting bracket.
1
2
Push the monitor station down until it is secure.
5 Take out the AC adaptor and the DC terminal from the case.
L Push the arrow mark on the front case, then release from the rear case.
L Take out the cardboard and wood screws. The wood screws are necessary when
attaching the AC adaptor and the DC terminal to a wall (page 16).
Arrow mark
AC adaptor
DC terminal
14
Introduction and Installation
6 Connect the power cable to the DC terminal, the power cord to the AC adaptor, then
connect the power cord to the AC outlet (100 V – 240 V, 50 Hz / 60 Hz).
L Be sure to connect the power cable to the 2 holes on the left side of the DC terminal.
L For details on how to attach the power cable, see page 18.
DC terminal
AC adaptor
Power cord
3
To AC outlet
2
Power cable
1
7 Attach the DC cord to the clamp on the rear of the DC terminal.
L This will help to avoid the DC cord to disconnect from the DC terminal.
DC terminal
DC cord
Clamp
15
Introduction and Installation
To attach the AC adaptor and the DC terminal to a wall
By placing the AC adaptor and the DC terminal in the case and mounting the case to the wall,
you can protect the AC adaptor and the DC terminal from tampering and exposure.
Note:
L Disconnect the DC cord from the clamp on the rear of the DC terminal beforehand. See
step 7 on page 15 for details.
L Take out the cardboard and wood screws from the AC case beforehand.
3
1 Attach the rear part of the case to a wall using the wood screws (4 mm x 16 mm, /16'' x
5
/8'').
Case
83.5 mm
(35/16
)
"
Wood screws
Wall
2 Pack the AC adaptor and DC terminal as shown.
1. Pack the AC adaptor in the rear case.
LBe sure to run the power cord through the power cord hole.
2. Pack the DC cord in the rear case.
LBe sure to bundle the DC cord so that it will not touch the bottom of the case.
3. Pack the DC terminal in the rear case.
LBe sure to run the wires through the wire hole, then under the wire rib.
Wire rib
Wire hole
3 DC terminal
1 AC adaptor
2 DC cord
Power cord
Power cord hole
16
Introduction and Installation
3 Attach the front of the case.
1
2
Note:
L To open the case again, push the bottom of the front case, then release from the rear case.
17
Introduction and Installation
To attach the power cable
Monitor station
DC terminal
Button
Button
Terminal
connector
Terminal connector
L While pressing on the button with a pointed object such as a screwdriver, insert the power
cable into the terminal connector.
L To disconnect the power cable, press on the button while pulling out.
1
L To attach an optional power cable, cut off about 12 mm ( /2") of the cable cover (1), then
push in firmly until the end of the cable is securely inserted into the power connection
terminal (2).
1
2 Power cable cross section
Correct Incorrect
12 mm
(1/2")
To attach the wires
Button
Terminal connector
3
L Strip off of the wire cover so that about 9 mm ( /8") of the wire is exposed.
L While pressing on the button with a pointed object such as a screwdriver, insert the wire into
the terminal connector.
L To disconnect a wire, press on the button while pulling out.
18
Introduction and Installation
Using the desktop stand (Optional)
You can place the monitor station on a desktop. See page 7 for optional item information.
Wood screws
Wire
Mounting bracket
Desktop stand
Power cable
Note:
L If you previously connected the power cable through the power cable guide (page 13),
remove the power cable from the power cable guide of the monitor station beforehand, then
attach to the desktop stand.
19
Using the Unit
Turning {PBX MODE} switch ON/OFF
When connecting to a PBX (page 22), turn {PBX MODE} switch on. If not, turn {PBX MODE}
switch off. The default setting is {ON}.
1 Remove the switch cover from the rear of the monitor station.
L Use a sharp, thin object such as a mechanical pencil.
Switch cover
2 Select {ON} (default) or {OFF}.
PBX MODE
OFF ON
{PBX MODE} switch
20
Using the Unit
3 Attach the switch cover to the rear of the monitor station.
Switch cover
21
Using the Unit
Connecting to a PBX
Connecting to a PBX allows you to answer door calls from any telephone. See page 11 for
wiring information.
Please use only a Panasonic PBX. See page 7 for the PBX model list that is compatible and
other optional hardware.
Important:
L Make sure {PBX MODE} switch is set to {ON} beforehand (page 20). The default
setting is {ON}.
PBX MODE
OFF ON
{PBX MODE} switch
Note:
L If you answer a call from the door station with a PBX extension, the camera image from the
door station will be displayed at the monitor station. If the monitor station user tries to
answer the call, a beep will sound. The display will turn off when the conversation has
ended or when the conversation continued for more than about 3 minutes.
L If you answer a call from the door station with the monitor station, the call will continue to
ring at the PBX for about 15 to 30 seconds. If the PBX user answers the call while the call
is still ringing, the door station user, the monitor station user, and the PBX user can speak
together.
22
Using the Unit
Answering a door call using the monitor station
There are 3 ways to answer a door call using the monitor station. Choose the desired mode
by changing the {ANSWER} switch position.
Important:
L When speaking with a caller, speak in turns. If you and the caller speak at the same
time, you will not hear each other.
Microphone
{BRIGHT}
ANSWER
AUTO
PUSH
{ANSWER} switch
HOLD
{TALK}
Talk indicator
Available answer modes
– {AUTO} mode: When a visitor calls you, you can answer the call by voice (page 24).
– {PUSH} mode (default): When a visitor calls you, you can answer the call by pressing
{TALK}. You may then speak with the caller (page 24).
– {HOLD} mode: When a visitor calls you, you can answer the call by pressing {TALK}.
Press {TALK} while speaking to the caller and release the button to allow the caller to
speak to you (page 24).
Note:
L If the door station is installed in a noisy environment, {PUSH} mode or {AUTO} mode may
not function properly.
23
Using the Unit
{PUSH} mode (Push to talk mode)
1 When a call is received from the door station, press {TALK}.
2 Speak to the visitor.
3 To end the conversation, press {TALK}.
L The display will turn off.
{AUTO} mode (Auto talk mode)
This mode allows you to answer the call by voice. Speak a brief reply into (or toward) the
monitor station, such as “Yes?” or “Hello?”. This reply is used to start {AUTO} mode; the
visitor will not hear your reply. The monitor station will beep to indicate {AUTO} mode has
started and you may then speak to the visitor.
1 When a call is received from the door station, answer “Yes?” within 30 seconds.
L A beep will sound to indicate that you can talk to the visitor (hands-free conversation).
2 Speak to the visitor.
3 To end the conversation, press {TALK}.
Note:
L Make sure you are within about 50 cm (20 inches) of the monitor station.
L You can also answer the call by pressing {TALK}.
L Your initial reply should be brief (less than 1 second), otherwise {AUTO} mode will not start.
L If a visitor calls you, a loud, brief sound (such as a barking dog) may start {AUTO} mode
even though you have not replied by voice.
{HOLD} mode (Hold to talk mode)
1 When a call is received from the door station, press and hold {TALK} to speak to the caller.
L A beep will sound and the Talk indicator will light.
2 To listen to the visitor, release {TALK}.
L The Talk indicator will turn off.
3 To speak again, press and hold {TALK}.
4 To end the conversation, tap {TALK}.
Note:
L Make sure you speak to the caller only while pressing {TALK} and release {TALK} when
you have stopped speaking so that the caller can speak to you.
24
Using the Unit
Note:
L Speak clearly about 50 cm (20 inches) away from the microphone.
L While the display is on, you can press {BRIGHT} repeatedly to select the desired
brightness. If a power failure occurs, the brightness setting will be reset.
L If you do not answer a door call within 30 seconds, the display will turn off. If you press
{TALK} again, the display will turn on again, and you can talk to the visitor.
L The conversation will be automatically disconnected in about 1 minute and 30 seconds
(about 1 minute in {HOLD} mode). To resume the conversation, press {TALK}.
L At night or when there is not enough lighting in the doorway, the display will be shown in
black and white.
25
Using the Unit
Monitoring the outside
You can monitor the sound and camera image from the door station for up to 1 minute at a
time.
{MONITOR}
{BRIGHT}
{TALK}
1 Press {MONITOR}.
L The outside image will be shown on the display, and the outside sound will be heard. The
inside sound will not be heard at the door station.
L If necessary, press {BRIGHT} repeatedly to select the desired brightness.
2 To end monitoring, press {MONITOR}.
L Even if you do not press {MONITOR}, monitoring will automatically end in about 1
minute.
Note:
L While you are monitoring, calls from the door station will not be heard.
L To talk to the visitor while monitoring, press {TALK}.
26
Using the Unit
Opening a door (door opener)
You can open the door using the monitor station (a separate door opener is required).
{DOOR}
1 While the display is on, press and hold {DOOR}.
L The door will remain open while {DOOR} is pressed.
Note:
L See page 11 for wiring information.
27
Help
Troubleshooting
Problem
Cause and solution
The display is not clear or is
blurry.
L The surface of the door station is dirty. Clean it with a
soft dry cloth.
L The surface of the door station is wet with dew. Wait for
the condensation to evaporate.
L Change the brightness of the display by pressing
{BRIGHT}.
The display is white, or black
or white lines are shown on
the display.
L Strong light such as sunlight is shining into the camera
of the door station. Though this may cause the display
image to become difficult to see, it is not a malfunction.
The color of the display is
different from the actual
color.
L Certain types of lighting (dusk, incandescent lighting,
etc.) may be shining into the camera. We recommend
lighting the area of the door station with white,
fluorescent light.
The display will not display
anything or no voices can be
heard.
L The power cord is not connected. Check the
connections.
L Contact our service personnel.
The monitor station does not
ring.
L The ringer volume is turned off. Turn it on.
L The power cord is not connected. Check the
connections.
L Contact our service personnel.
I cannot talk to the visitor or
the ringer tone rings
regularly.
L Press and hold {BRIGHT} for about 10 seconds until a
beep sounds. Wait for another 10 seconds and try
again.
L Contact our service personnel.
Sound cuts in/out or fades.
L The surroundings of the monitor station or the door
station are noisy. If you are using {PUSH} mode or
{AUTO} mode, your conversation may be interrupted.
Try {HOLD} mode.
{AUTO} mode does not
operate properly.
L Your voice is not loud enough or your initial reply is too
long (must be less than 1 second). Try a different voice
volume or change the length of your answer until the
monitor station beeps.
Your voice cannot be heard
by the outside visitor.
L {ANSWER} switch is set to {HOLD} mode. Only while
you press {TALK}, the outside visitor can hear your
voice. Select another setting.
The outside visitor complains
the door station does not
beep when the call button is
pressed.
L {PBX MODE} switch is turned on although the unit is
not connected to a PBX. Turn off {PBX MODE} switch
(page 20).
28
Help
Problem
Cause and solution
The display turns off during a
conversation (Sound
continues).
L You talked for more than about 3 minutes in {HOLD}
mode. The maximum display time is approximately 3
minutes.
Cleaning
Clean the unit with a soft, dry cloth when cleaning. For excessive dirt, wipe the unit with a
slightly damp cloth.
Important information:
L Do not use anything containing alcohol, polish powder, powder soap, benzine, thinner, wax,
petroleum, or boiling water. Also do not spray with insecticide, glass cleaner, or hair spray.
This could cause a change in color or quality.
29
General Information
Technical data about this product
Monitor station
Power supply:
24 V DC
Current consumption:
Standby: Approximately 37 mA
At operation: Approximately 420 mA
Dimensions:
Approximately height 136 mm x width 136 mm x depth 32 mm
(5 /8" x 5 /8" x 1 /4")
3
3
1
Mass (Weight):
Approximately 350 g (0.77 lb.)
Operating environment: 0 °C to 40 °C (32 °F to 104 °F), Up to 90% RH
(Relative Humidity) non condensing
Installation method:
External material:
Wall mount (Wall mount bracket included)
Flame retardant ABS resin (panel: acrylic resin)
Note:
L To connect to a door opener, make sure the door opener is:
– Normal open (Low active)
– Less than 30 V AC (1 A), 24 V DC (1 A)
AC adaptor (Part number: PFAP1014)
Power supply:
Output voltage:
Output current
Dimensions:
100 V – 240 V AC, 50 Hz / 60 Hz
24 V DC
2 A
Approximately height 120 mm x width 60 mm x depth 35 mm
3
3
3
(4 /4" x 2 /8" x 1 /8")
Mass (Weight):
Approximately 310 g (0.68 lb.)
Operating environment: 0 °C to 40 °C (32 °F to 104 °F), Up to 90% RH
(Relative Humidity) non condensing
Note:
L Design and specifications are subject to change without notice.
L The pictures and illustrations in these instructions may vary slightly from the actual
product.
30
General Information
FCC and Other Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation.
CAUTION:
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate this device.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
— Consult the dealer or an experienced radio/TV technician for help.
31
For your future reference
Date of purchase
Serial number (found on the rear of the unit)
Dealer’s name and address
Dealer’s telephone number
Attach your sales receipt here.
Panasonic Consumer Electronics Company,
Division of Panasonic Corporation of North America
One Panasonic Way, Secaucus, New Jersey 07094, U.S.A.
Panasonic Puerto Rico, Inc.
San Gabriel Industrial Park, Ave. 65 de Infantería, Km. 9.5, Carolina, Puerto Rico 00985,
U.S.A.
Copyright:
L This material is copyrighted by Panasonic Communications Co., Ltd., and may be
reproduced for internal use only. All other reproduction, in whole or in part, is prohibited
without the written consent of Panasonic Communications Co., Ltd.
© 2005 Panasonic Communications Co., Ltd. All Rights Reserved.
PFQX2164ZA DC0405NK0
|