Panasonic BT 3DL2550P User Manual

Operating Instructions

LCD Video Monitor

Model No.

BT-3DL2550P

BT-3DL2550E

ESPAÑOL

Para la explicación en español, consulte el CD-ROM uministrado.

Before operating this product, please read the instructions carefully and save this manual for future use.

ENGLISH

SS0710AT0 -FJ @

Printed in Japan

VQT2U10

Read this first! (for BT-3DL2550P) (continued)

FCC NOTICE (USA)

Declaration of Conformity

Model Number:

Trade Name:

BT-3DL2550P

Panasonic

Responsible Party:

Panasonic Corporation of North America

One Panasonic Way, Secaucus, NJ07094

1-800-524-1448

Support contact:

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

To assure continued compliance, follow the attached installation instructions and do not make any

unauthorized modifications.

Note:

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter-

ference in a residential installation. This equipment generates, uses, and can radiate radio frequency

energy, and if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular instal-

lation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

The user may find the booklet “Something About Interference” available from FCC local regional offices helpful.

Warning:

To assure continued FCC emission limit compliance, follow the attached installation instructions and the user

must use only shielded interface cables when connecting to host computer or peripheral devices. If DVI-D port

is to be used it must connected to PC by compatible interface cable with two ferrite cores. Also, any

unauthorized changes or modifications to this equipment could void the user’s authority to operate this device.

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (includ-

ing amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The

wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold

with the apparatus. When a cart is used, use caution when moving the cart/apparatus combi-

nation to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

S3125A

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not oper-

ate normally, or has been dropped.

Read this first! (for BT-3DL2550E)

WARNING:

This apparatus must be earthed.

CAUTION:

The mains plug of the power supply cord shall

To ensure safe operation the three-pin plug must

be inserted only into a standard three-pin power

point which is effectively earthed through the

normal house-hold wiring. Extension cords used

with the equipment must be three-core and be

correctly wired to provide connection to earth.

Wrongly wired extension cords are a major cause

of fatalities. The fact that the equipment operates

satisfactorily does not imply that the power point is

earthed and that the installation is completely safe.

For your safety, if in any doubt about the effective

earthing of the power point, consult a qualified

electrician.

remain readily operable.

The AC receptacle (mains socket outlet) shall be

installed near the equipment and shall be easily

accessible. To completely disconnect this

equipment from the AC mains, disconnect the

mains plug from the AC receptacle.

CAUTION:

To reduce the risk of fire or electric shock and

annoying interference, use the recommended

accessories only.

CAUTION:

In order to maintain adequate ventilation, do not

WARNING:

install or place this unit in a bookcase, built-in

cabinet or any other confined space. To prevent

risk of electric shock or fire hazard due to

overheating, ensure that curtains and any other

materials do not obstruct the ventilation.

• To reduce the risk of fire or electric shock, do not

expose this equipment to rain or moisture.

• To reduce the risk of fire or electric shock, keep this

equipment away from all liquids. Use and store only

in locations which are not exposed to the risk of

dripping or splashing liquids, and do not place any

liquid containers on top of the equipment.

CAUTION:

Excessive sound pressure from earphones and

headphones can cause hearing loss.

WARNING:

Always keep accessories (AC mains lead hook,

CAUTION:

screw) out of the reach of babies and small

children.

This Monitor is for use only with Panasonic Wall

Mount Adaptor, BT-WMA26G. Use with other Wall

Mount is capable of resulting in instability causing

possible injury.

WARNING:

Installation should only be performed by qualified

installation personnel.

CAUTION:

Improper installation may result in the entire

apparatus falling down and causing injury.

Check the installation at least once a year.

An improper installation could cause the monitor to

fall off resulting in personal injury.

CAUTION:

Do not remove panel covers by unscrewing them.

CAUTION:

To reduce the risk of electric shock, do not remove

the covers. No user serviceable parts inside. Refer

servicing to qualified service personnel.

Remove the wall mount adaptor when not used.

Otherwise people moving in the vicinity of the

monitor could get caught on the bracket and be

injured.

indicates safety information.

AC Adapter

The rating plate is on the underside of the AC Adapter.

Operating precaution

Operation near any appliance which generates strong magnetic fields may give rise to noise in the video and

audio signals. If this should be the case, deal with the situation by, for instance, moving the source of the magnetic

fields away from the unit before operation.

EEE Yönetmeliğine Uygundur.

EEE Complies with Directive of Turkey.

Read this first! (for BT-3DL2550E) (continued)

Caution for AC Mains Lead

FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.

This product is equipped with 2 types of AC mains cable, Type C and Type BF.

Appropriate mains cable must be used in each local area, since the other type of mains cable is not suitable.

TYPE C

For continental Europe, Russia, etc.

Not to be used in the U.K.

TYPE BF

For U.K., etc.

TYPE BF

This appliance is supplied with a moulded three pin mains

plug for your safety and convenience.

A 13 amp fuse is fitted in this plug.

Should the fuse need to be replaced please ensure that

the replacement fuse has a rating of 13 amps.

If the plug contains a removable fuse cover you must

ensure that it is refitted when the fuse is replaced.

If you lose the fuse cover the plug must not be used until a

replacement cover is obtained.

A replacement fuse cover can be purchased from your

local Panasonic Dealer.

For U.K. only

The replacement fuse must be approved by ASTA or BSI

to BS1362. Check for the ASTA mark

on the body of the fuse.

or the BSI mark

How to replace the fuse

1.Open the fuse compartment with a screwdriver.

2.Replace the fuse.

Fuse

indicates safety information.

Read this first! (for BT-3DL2550E) (continued)

EMC NOTICE FOR THE PURCHASER/USER OF THE

APPARATUS

1. Applicable standards and operating environment (BT-3DL2550E)

The apparatus is compliant with:

• standards EN55103-1 and EN55103-2 1996.11, and

• electromagnetic environments E1, E2, E3 and E4

2. Pre-requisite conditions to achieving compliance with the above standards

<1> Peripheral equipment to be connected to the apparatus and special connecting cables

• The purchaser/user is urged to use only equipment which has been recommended by us as

peripheral equipment to be connected to the apparatus.

• The purchaser/user is urged to use only the connecting cables described below.

<2> For the connecting cables, use shielded cables which suit the intended purpose of the

apparatus.

• Video signal connecting cables

Use double shielded coaxial cables, which are designed for 75-ohm type high-frequency applications,

for SDI (Serial Digital Interface).

Coaxial cables, which are designed for 75-ohm type high-frequency applications, are recommended

for analog video signals.

• Audio signal connecting cables

If your apparatus supports AES/EBU serial digital audio signals, use cables designed for AES/EBU.

Use shielded cables, which provide quality performance for high-frequency transmission applications,

for analog audio signals.

• Other connecting cables (IEEE1394, USB)

Use shielded cables, which provide quality performance for high-frequency applications, as

connecting cables.

• When connecting to the DVI signal terminal, use a cable with a ferrite core.

• If your apparatus is supplied with ferrite core(s), they must be attached on cable(s) following

instructions in this manual.

• Use a sealed type cable (D-SUB 9 pin) for connecting to the GPI terminal.

3. Performance level

The performance level of the apparatus is equivalent to or better than the performance level required by

these standards.

However, the apparatus may be adversely affected by interference if it is being used in an EMC environ-

ment, such as an area where strong electromagnetic fields are generated (by the presence of signal trans-

mission towers, cellular phones, etc.). In order to minimize the adverse effects of the interference on the

apparatus in cases like this, it is recommended that the following steps be taken with the apparatus being

affected and with its operating environment:

1. Place the apparatus at a distance from the source of the interference.

2. Change the direction of the apparatus.

3. Change the connection method used for the apparatus.

4. Connect the apparatus to another power outlet where the power is not shared by any other

appliances.

Pursuant to at the directive 2004/108/EC, article 9(2)

Panasonic Testing Centre

Panasonic Service Europe, a division of Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg, F.R. Germany

Cautions

About 3D Polarized Eyewear

• Do not drop, exert pressure on, or step on the 3D Polarized Eyewear.

• Be careful not to trap a finger in the hinge section of the 3D Polarized Eyewear.

• Always store the 3D Polarized Eyewear in the case provided when not in use.

• Be careful of the tips of the frame when putting on the 3D Polarized Eyewear.

Viewing 3D Content

• Use this monitor at the recommended viewing distance.

(Recommended viewing distance: 80cm approx.)

• Aim to take breaks of between 30 - 60 minutes as appropriate when viewing 3D content.

• As a guideline, do not allow children younger than 5 - 6 years old to view 3D content.

• Stop using the 3D Polarized Eyewear immediately if you feel tired, discomfort, or any other uncomfortable

sensation.

• Be aware of objects and people in your surroundings when viewing 3D content.

• The 3D Polarized Eyewear must only be worn when viewing 3D content.

• Do not tilt your head and/or the 3D Polarized Eyewear while viewing 3D image.

• Keep your eyes and the 3D Polarized Eyewear is on a horizontal level to the television.

• If you suffer from any eyesight problems (short/far-sighted, astigmatism, eyesight differences in left and right),

please ensure to correct your vision before using the 3D Polarized Eyewear.

• Stop using the 3D Polarized Eyewear if you can clearly see double images when viewing 3D content.

• Do not use the 3D Polarized Eyewear if you have a history of over-sensitivity to light, heart problems, or have any

other existing medical conditions.

3D Polarized Eyewear Use

• Stop using the 3D Polarized Eyewear immediately if you feel tired, discomfort, or any other uncomfortable

sensation.

• Remove the 3D Eyewear before moving around to avoid falling or accidental injury.

• Use the 3D Polarized Eyewear only for the intended purpose and nothing else.

• Stop using the 3D Polarized Eyewear immediately if a malfunction or fault occurs.

• Do not use if the 3D Polarized Eyewear is physically damaged.

• Immediately discontinue use of 3D Polarized Eyewear if they are damaged or faulty.

• In rare cases, the materials used in the 3D Polarized Eyewear may cause an allergic reaction.

• Stop using the 3D Eyewear immediately if you experience any redness, pain, or skin irritation around the nose or

temples.

• Do not use the 3D Polarized Eyewear if you have a history of over-sensitivity to light, heart problems, or have any

other existing medical conditions.

Transportation precautions

Do not try to lift the

monitor by grabbing

the panel.

Do not place the monitor face down during transportation to prevent

damaging it. Keep it upright.

Do not expose the LCD panel to strong pressure or pressure from pointed objects. Take care especially during

transportation.

Exposing the LCD panel to strong pressure may result in blurring or other damage.

Precautions for Use

• The LCD screen is manufactured to precise specifications. Although over 99.99% of the pixels function normally,

0.01% of the pixels are either missing or constantly lit (red, blue or green). This is normal and not a cause for

concern.

• The liquid crystal protection panel is a specially manufactured component. Wiping it with a hard cloth, or rubbing it

vigorously will scratch the surface.

• If a still image is displayed for an extended period of time, it may generate a temporary afterimage (phosphor

burn-in). (However, such images can be removed by displaying normal video for a while.)

• The response speed and brightness of liquid crystal vary with ambient temperatures.

• Let authorized service person handle installation.

Be sure to consult with the service person about the installation. Make sure that the wall is strong enough to

endure the weight of this unit including the mount fittings. If not strong enough, it may fall off resulting in injury.

• Do not install the unit in a place exposed to direct sunlight, as it may damage the cabinet and the LCD screen.

• Do not install the unit in locations where enough space cannot be provided around it as heat may build up inside

preventing normal operation. Be sure to provide enough space around the unit.

• Exposing the LCD screen to intense light sources will impair its characteristics and lower image quality.

• In an environment exposed to drastic temperature fluctuations, condensation may build up on and inside the LCD

screen. This may lower the quality of the screen and may damage it.

• Some video images may appear blurred on the screen.

• Leaving the unit in a location exposed to high temperature and humidity for an extended period of time may

damage the LCD screen and cause blurring.

Contents

Read this first!. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Cautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Transportation precautions . . . . . . . . . . . . . . . . . . . 7

Precautions for Use . . . . . . . . . . . . . . . . . . . . . . . . . 8

Standard accessories . . . . . . . . . . . . . . . . . . . . . . . 8

Optional units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Controls and Their Functions . . . . . . . . . . . . . . . . 12

Video monitor unit ................................................. 12

Front panel controls .............................................. 13

Rear panel terminals............................................. 14

AC Adapter............................................................ 15

Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

How to Use the On Screen Menu. . . . . . . . . . . . . . 17

User Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Menu configuration................................................ 23

3D.......................................................................... 24

MARKER............................................................... 25

Marker types.......................................................... 27

VIDEO CONFIG .................................................... 29

SYSTEM CONFIG................................................. 32

FUNCTION............................................................ 35

GPI ........................................................................ 39

INPUT SELECT..................................................... 40

AUDIO................................................................... 42

DISPLAY SETUP .................................................. 43

CONTROL............................................................. 48

HOURMETER ....................................................... 48

REMOTE Specifications . . . . . . . . . . . . . . . . . . . . . 53

Maintenance inspections . . . . . . . . . . . . . . . . . . . . 57

Care and cleaning of the monitor . . . . . . . . . . . . . 58

Care and storage of 3D Polarized Eyewear . . . . . 58

Error Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Before calling for support . . . . . . . . . . . . . . . . . . . 58

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Standard accessories

Power cable × 1

AC mains lead × 2

Power cable hook × 1

Screw × 1 (for securing power cable)

AC Adaptor × 1 (VEK0N61)

DC cable × 1

AC mains lead hook × 1

Screw × 1 (for securing AC mains lead)

AC Adaptor × 1 (VEK0N62)

DC cable × 1

CD-ROM × 1

3D Polarized Eyewear (BT-PGL10G) × 2

Optional units

Wall Mount Adaptor

BT-WMA26G (Leave installation of the wall mount adaptor to authorized personnel.)

3D Polarized Eyewear BT-PGL10G (same as those included with unit)

Outline

The BT-3DL2550P/E LCD monitor is a 64.8 cm (25.5 inch) full HD LCD display panel designed especially for

broadcasting service and business use.

_Compact 25.5 type full HD monitor

• The monitor is equipped with a high-resolution (1920 x 1200) IPS LCD panel.

• Efforts to develop a small footprint have resulted in a surprisingly compact design for a monitor with a screen

size of 64.8 cm (25.5 inches).

_Wide color gamut panel and 10-bit 3D LUT for faithful color reproduction

• The wide color gamut panel increases the origin coordinate accuracy of broadcast standard RGB and 3D LUT

improves color reproduction. It is also compatible with the wide color gamut modes for the Adobe RGB and D-

Cinema (D-Cinema min. Color Gamut) standards.

_A new image processing engine for improved video quality

• 10-bit image processing accurately and smoothly reproduces color from low to high brightness levels.

•

Built-in I/P converter circuit with a delay of less than 1 field minimizes the delay between input signal to picture display.

• Diagonal line compensation processing circuit reduces vertical image degradation and jagged noise in the

diagonal direction.

• High-speed motion response results in crisp image reproduction without blurring.

• The gamma correction of each monitor is set individually prior to shipment.

_Multi-format image compatibility

•

This monitor is equipped with SDI (HD/SD compatible), VIDEO, YPBPR/RGB, DVI-D (HDCP compatible) input jacks.

• It supports both NTSC and PAL TV broadcast systems.

_3D display function

Along with a standard 2D display function, this monitor is equipped with a function that displays a left-eye and

right-eye image on each line, creating a 3D (stereoscopic) image when viewed through the 3D Polarized

Eyewear provided.

Due to the characteristics of the Xpol^®polarizing filter, 3D images should be viewed from a position directly in

front of the LCD screen.

The supplied 3D Polarized Eyewear can be worn over regular prescription glasses.

• Compatible with various input types

SIMULTANEOUS (SIMUL)

The monitor converts left-eye and right-eye video input from the SDI1 and SDI2 terminals into a 3D image.

Left-eye image

Monitor

SDI1 (L)

Right-eye image

SDI2 (R)

LINE BY LINE

Left-eye and right-eye video is combined into a single image using an external device and the image is input

from SDI1, SDI2, or DVI-D and displayed as a 3D image by the monitor.

Left-eye image

Monitor

External

Right-eye image

device

SDI1/SDI2/

DVI-D

Outline (continued)

SIDE BY SIDE

A signal split into video for left-eye and right-eye and arranged side by side is input from either SDI1 or SDI2

and converted into a 3D image and displayed by the monitor.

Input through DVI-D is also supported.

Right-eye

image

Left-eye

image

Monitor

SDI1/SDI2/

DVI-D

• 3D display adjustment function

This function can horizontally invert the right-eye image and shift its position horizontally.

• Support for various display formats

Multiple formats to check the difference between left-eye and right-eye images are also provided.

OVERLAY

Video for the left-eye and right-eye is overlaid on a single screen and displayed on the monitor.

SDI1 (L)/SDI2 (R)

When SDI1 is selected video input from SDI1 (L) is displayed on a single screen, and when SDI2 is selected

video input from SDI2 (R) is displayed on a single screen.

COMPARISON

Video for the left-eye and right-eye is displayed separately side by side.

_A host of functions

2D ONLY

• Split-screen function

You can display two selected inputs in two windows and set a separate color space and gamma value for

image comparison.

• Time code display

During HD SDI input, you can select to display VITC, LTC or UB time code. When in 3D mode, the time code

from the SDI1 terminal input signal is displayed.

2D ONLY

• Closed caption

During VIDEO (NTSC) input, this feature displays the closed caption information embedded in the video signal.

(EIA-608 compliant)

• Cross hatch overlay function

Displays markers at regular vertical and horizontal intervals to facilitate composition.

_Calibration function

The monitor can easily be calibrated using a luminance meter.

_REMOTE control

Depending on the intended use of the monitor, you can select between parallel remote control (GPI) and serial

remote control (RS-232C).

3D ONLY

In these operating instructions, points that apply only when displaying 3D images are marked

, and points

2D ONLY

that apply only when displaying 2D images are marked

• Xpol^®is a registered trademark of Arisawa Mfg. Co., Ltd.

• Adobe is the registered trademark or trademark of Adobe System Incorporated in the United States and other

countries.

• Other company names and product names are the trademarks or registered trademarks of their respective

owners.

Dimensions

Video monitor unit

Unit: mm (inches)

346 (13.6)

370 (14.6)

100 (3.9)

60 (2.4)

599 (23.6)

10-M4,L=10mm Max

550.08 (21.7)

200 (7.9)

100 (3.9)

169 (6.7)

215 (8.5)

• When installing the monitor in one place permanently, we recommend that you fix the monitor in

place using the screw holes in the lower part of the stand.

AC Adaptor

Unit: mm (inches)

48.5 (1.9)

73.5 (2.9)

64 (2.5)

46 (1.8)

232 (9.1)

200 (7.9)

• The rating plate is on the underside of the AC Adapter.

Controls and Their Functions

Video monitor unit

Front view

Rear view

Tally lamp (Jpage 39, 53)

The color of the tally lamp Indicates monitor status. Red tally or green tally displayed according to GPI input.

Front panel controls (Jpage 13)

POWER switch (

)

The POWER switch is located at the bottom of the front panel.

This switch turns the power On and Off. Set the switch to

to turn it on.

Power LED

When the power is turned on, the LED lights green.

DC IN

Connect the supplied DC cable of the supplied AC adapter to this terminal.

Rear panel terminals (Jpage 14)

Controls and Their Functions (continued)

Front panel controls

INPUT button (

)

Selects the signal input line.

Each press of the button changes the lines in the following order: VIDEO J SDI1 J SDI2 J YP^BPR/RGB J

DVI-D.

VIDEO

SDI1

SDI2

VIDEO input (analog composite signal)

Serial digital interface input (HD/SD compatible)

YP^BPR/RGB : Analog component input (YPBPR) or RGB input also compatible with RGB input from a PC.

DVI-D DVI-D input (HDCP compatible)

• When the power is turned on, the input line used when the power was last turned off is selected.

The INPUT menu can be set to skip input lines that are not used.

• VIDEO and YP^BPR/RGB cannot be selected while in 3D mode.

MENU button (

Press to open a menu, exit a menu or return to a previous menu.

ADJUST button (

)

Press to display the picture/volume adjusting menu (PHASE, CHROMA, BRIGHT, B.LIGHT [BACKLIGHT] or

CONT. [CONTRAST], VOLUME).

Cursor, ENTER, FUNCTION buttons (

)

/FUNCTION1

/FUNCTION2

/FUNCTION3

/FUNCTION4

: Moves the cursor to the left. Use to select the picture/volume adjusting menu or to

confirm a menu item assigned to the FUNCTION1.

: Moves the cursor to the right. Use to select the picture/volume adjusting menu or to

confirm a menu item assigned to the FUNCTION2.

: Moves the cursor downwards. Use to select the picture/volume adjusting menu or to

confirm a menu item assigned to the FUNCTION3.

: Moves the cursor upwards. Use to select the picture/volume adjusting menu or to

confirm a menu item assigned to the FUNCTION4.

ENTER/FUNCTION5 : Confirms a menu selection and opens a submenu. It also confirms a menu item

assigned to the FUNCTION5.

• When the control lock is on, the key mark appears and FUNCTION does not operate.

The buttons are made of plastic film. Do not use pointed objects such as fingernails, pens or screwdrivers to press

the buttons as the resulting damage or deformation could prevent proper contact.

Controls and Their Functions (continued)

Rear panel terminals

SDI terminal (BNC) ^*1*2

IN1 : This is the SDI input terminal (compatible with HD/SD automatic switching).

• In 3D mode with simultaneous double input (SIMUL), this is the L input terminal.

IN2 : This is the SDI input terminal (compatible with HD/SD automatic switching).

• In 3D mode with simultaneous double input (SIMUL), this is the R input terminal.

OUT1 : SDI output terminal (active through output)

• Output (active through) is available when the “SDI1” and “SDI2” options in the “INPUT SELECT” menu are

set to “ON”, and “SDI1” or “SDI2” is selected via the INPUT button.

OUT2 : SDI output terminal (active through output)

• Output (active through) is available when the “SDI1” and “SDI2” options in the “INPUT SELECT” menu are

set to “ON”, and “SDI1” or “SDI2” is selected via the INPUT button.

DVI-D terminal (DVI-D) ^*3

An HDCP compliant DVI-D signal input terminal.

VIDEO terminal (BNC) ^*4

: This is the VIDEO signal (analog composite signal) input terminal.

OUT : This is the input signal through-out terminal.

AUDIO IN terminal (pin jack)

This is the common audio input terminal for all video input terminals.

• Audio from SDI input is selected automatically when the “SDI1” and “SDI2” options in the “INPUT SELECT”

menu are set to “ON”, and the “INPUT SELECT” option of the “AUDIO” menu is set to “AUTO”.

Y/G, P^B/B, PR/R terminal (BNC) ^*4*5

: This is the YPBPR/RGB signal input terminal.

OUT : This is the input signal through-out terminal.

SYNC/HD, VD terminal (BNC) ^*6

: This is the input terminal for external synchronizing SYNC/HD, VD signals.

OUT : This is the input signal through-out terminal.

• When using RGB signals from a PC, connect the horizontal synchronizing signal to the SYNC/HD terminal,

and the vertical synchronizing signal to the VD terminal.

*1 Use double-sealed type cables for connecting to SDI input/output terminals.

*2 When inputting 3D image signals, ensure that left and right signals are input into the correct terminal.

*3 Use a DVI cable with a ferrite core.

*4 Unless a cable is connected to the OUT terminal, the IN terminal is automatically terminated at 75 Ω.

Since a connection to the OUT terminal releases the 75 Ω termination of the unit, the level of the VIDEO signal input to the

unit may become too large depending on the connected device.

*5 When a device is connected to the OUT terminal, 1080p and PC input and other broadband signals may distort character

outlines and other details.

*6 Unless a cable is connected to the OUT terminal, the IN terminal is automatically terminated at 1 kΩ. Making a connection to

the OUT terminal will automatically release the 1 kΩ termination.

Controls and Their Functions (continued)

GPI input terminal (D-SUB 9-pin) ^*1

External control is possible by using a GPI signal.

RS-232C terminal (D-SUB 9-pin)

External control is possible by using an RS-232C signal.

HEADPHONES output connector (stereo mini-jack M3)

Connect a pair of headphones to monitor the sound.

• The sound volume and sound quality will depend on the headphones.

*1 Use a sealed type cable (D-SUB 9 pin) for connecting to the GPI terminal.

AC Adapter

AC IN (AC inlet)

This is the AC input terminal.

POWER switch (ON : , OFF :

)

This switch turns the AC adapter on and off.

POWER lamp

This lamp lights green when the POWER switch is set to on.

DC OUT

This is the DC output terminal.

This terminal enables connection of a DC cable.

Power Supply

Connecting the power cable

1. Connect the power cable to the AC inlet of the

AC adapter.

4. Connect the power cable to an AC outlet.

5. Turn on the POWER switch. The POWER LED

lights green.

Power cable hook

Power cable

Screw

Use the supplied screw (for securing power cable)

and the power cable hook to secure the power cable

to the AC adapter.

Be sure to use the supplied AC adapter.

Do not use the supplied AC adapter for powering

other devices.

2. Slide the supplied DC cable into the DC OUT

terminal on the AC adapter until it is locked in

place.

The AC adapter generates heat during use, which is

normal and not a cause for concern.

Pin number

Signal

GND

+5 V

+24 V

DC IN terminal

3. Slide the DC cable into the DC IN terminal on the

unit until it locks in place.

How to Use the On Screen Menu

The screen displays eight types of information: input signal status, picture/volume adjusting menu status,

sharpness display, FUNCTION display, audio level meter display, menu display, TIME CODE display and CLOSED

CAPTION display.

Input signal status

_2D mode

_3D mode

SIMUL

LINE BY LINE

SDI1(L): 1080/59.94i(L)

SDI2(R): 1080/59.94i(R)

1. Main window , sub-window

indication

6. 3D display

• Indicates whether the main window or sub-window

is displayed.

• This indicates that “SYSTEM” is set to “3D” in the

“3D” menu.

•

In split screen display, the screen synchronized to the

reference sync changes with the input signal format

7. 3D INPUT TYPE display

• This indicates the “3D INPUT TYPE” of the “3D”

and “TWO WINDOW SIZE” settings (

page 47).

The screen synchronized to the reference sync is

displayed in white and the screen that is not

synchronized is displayed in yellow.

8. SIMUL MODE display

•

This indicates the options for “SIMUL MODE” when

“3D INPUT TYPE” is set to “SIMUL” in the “3D” menu.

2. The selected input line (J page 13,

• VIDEO, SDI1, SDI2,

)

9. H SHIFT display

• This is displayed when the “3D INPUT TYPE” of the

“3D” menu is set to “SIMUL” and the SDI2 signal is

being shifted horizontally using “H SHIFT”.

10. SDI1 (L) display

YP^BPR/RGB-VIDEO/RGB-COMP.

DVI-VIDEO/DVI-COMP.

•

Use “STATUS DISPLAY” in the “SYSTEM CONFIG”

menu to set the display status ( page 32).

3. Various indications (FILM mode)

•

This indicates the format of the signal input from the

SDI1 (L) terminal. When SIMUL is selected,

• This indicates that “GAMMA SELECT” is set to

“FILM” in the “VIDEO CONFIG” menu.

4. Signal format

synchronization is performed based on the left signal.

11. SDI2 (R) display

•

This indicates the format of the signal input from the

SDI2 (R) terminal. When SIMUL is selected,

•

Use “STATUS DISPLAY” in the “SYSTEM CONFIG”

menu to set the display status ( page 32).

• “UNSUPPORT SIGNAL appears if an unsupported

signal is input. It may also indicate that the format

synchronization is performed based on the left signal.

12. (L)(R) display

”

• This displays left and right information when a

signal that has left and right information

superimposed (such as AG-3DA1) is input through

SDI1.

If left and right input is mistakenly reversed, it is

displayed in yellow.

selected in the “INPUT SELECT

match the input signal.

”

menu does not

• “NO SIGNAL

”

appears if no signal is input.

Note:

“UNSUPPORT SIGNAL

”

and “NO SIGNAL may

”

not be properly displayed.

5. Various indications (Lock status)

Left and right information is not displayed if it is

input through SDI2 only.

• This indicates that “CONTROL” is set to “REMOTE”

in the “CONTROL” menu.

How to Use the On Screen Menu (continued)

Picture/volume adjusting menu

• Press the ADJUST button (J page 13, ) to open the

picture/volume adjusting menu.

• To clear the display, press the ADJUST button again,

press the MENU button or leave it idle for 10 seconds.

• Only adjustments that appear on the screen can be

adjusted.

• The display always appears in the same screen

location.

Sharpness display

• This is the SHARPNESS H/V mode display.

• It disappears after 2 minutes of inaction.

• Displayed when setting SHARPNESS H in 3D mode.

FUNCTION display

• Use the menu to open and set up functions.

• When “FUNCTION DISPLAY” (J page 36) is set to

“ON1” or “ON2”, pressing any of the “FUNCTION1” to

“FUNCTION5” buttons displays the item and the

status of the item for the respective FUNCTION.

• This display disappears after 2 seconds of inaction.

• “XXXXX” indicates operating status (J page 38,

“Functions and operating status displayed on screen

when FUNCTION buttons are pressed”).

F1:MARKER

F2:CROSS HATCH

F3:BLUE ONLY

F4:TIME CODE

F5:LEVEL METER

XXXXX

Audio level meter display

• A white skeleton bar meter indicates the audio level

for SDI signals. When 3D mode is set to SIMUL, audio

from the SDI signal input via SDI1 is always used.

• You can switch the level display on/off and set the

number of displayed channels using the menu

(J page 42, “AUDIO”).

• The 0 dB line and channel display can be switched

on/off from the menu (J page 42, “AUDIO”).

Note:

When SDI2 and another input (except for a

combination of SDI1 and SDI2) are used for the split

screen display, TIME CODE and audio level meter

display will not function. In this case, use SDI1.

Channel Level

display display

0 dB line

How to Use the On Screen Menu (continued)

Menu display

• This is the menu display.

• It disappears after 2 minutes of inaction.

• You can change position of the display (J page 32,

“MENU POSITION”).

[MAIN MENU]

• Options unavailable in 3D mode appear gray and

cannot be selected.

Displays instructions on menu button operations.

TIME CODE display (TC)

• Use the menu to display and set the time code for HD-

SDI signal input. It also allows you to switch display

mode (VITC, LTC, VUB, LUB).

In VITC and LTC display mode:

• Displays the time code in hours: minutes: seconds: or

frames.

• In drop-frame mode, a different delimiter between

seconds and frames is used.

Note:

• Read errors are displayed as “--:--:--:--”

• Displays the VITC/LTC of the HD SDI signal from

SDI1 terminal when 3D mode is set to SIMUL.

( : ) NDF

( . ) DF

In VUB and LUB display modes:

• BG8, BG7, BG6, BG5, BG4, BG3, BG2, BG1 appear

in the stated order. BG: binary group

• The (:) delimiter does not appear.

Note:

• Read errors are displayed as “--:--:--:--”

• Displays the VUB/LUB of the HD SDI signal from

SDI1 terminal when 3D mode is set to SIMUL.

• Display position and character size can be modified

(J page 43, “POSITION” and “FONT SIZE” in the

“DISPLAY SETUP” menu).

• When SDI2 and another input (except for a

combination of SDI1 and SDI2) are used for the split

screen display, TIME CODE and audio level meter

display will not function. In this case, use SDI1.

How to Use the On Screen Menu (continued)

2D ONLY

CLOSED CAPTION (CC) display

• Use the menu to display and set closed caption

display for VIDEO (NTSC) signals. It also allows you

to select display mode (CC1 to CC4) (J page 43,

“CLOSED CAPTION” and “MODE SELECT” in the

“DISPLAY SETUP” menu.).

Note:

• Closed captions are not available during HV DELAY.

• In split-screen display, closed captions appear only

when a VIDEO input line is displayed in the main

window.

Menu operations

1. Press [MENU] to display the MAIN menu.

3. Press [

[ENTER].

] to select a sub menu and press

The settings in the sub menu change to green.

2. Press [

[ENTER].

] to select a menu and push

[MAIN MENU]

4. Press [

[ENTER].

] to select a setting, then press

To cancel, press [MENU].

To return to the previous screen

Press the [MENU] button.

How to Use the On Screen Menu (continued)

Picture/volume adjusting menu operations

1. Press [ADJUST] to display the picture/volume

adjusting menu.

2. Press [

] to select item to adjust.

The selected item changes to white.

3. Press [

PHASE

] to adjust.

0 - 60 (30)

0, 10 - 60 (30)

0 - 60 (30)

0 - 60 (50)

0 - 60 (0)

CHROMA

BRIGHT

B.LIGHT [BACKLIGHT]

VOLUME

( ) : Factory defaults

• Setting [B.LIGHT/CONT.] to CONT. [CONTRAST]

in the [SYSTEM CONFIG] menu changes the

B.LIGHT indication to CONT. enabling CONTRAST

adjustment.

CONT. [CONTRAST]

0 - 60 (50)

• Adjustments are not possible under the following

conditions.

- When “CONTROL” in the “CONTROL” menu is

set to “REMOTE,” the key mark appears and

adjustments cannot be changed.

- Setting the MONO function to ON (J page 30)

disables the [PHASE] and [CHROMA]

operations.

- During “RGB-COMP.” and “DVI-COMP.” input, the

[PHASE] and [CHROMA] operations are

disabled.

- During HV DELAY (J page 37) operation (and a

setting other than OFF is selected), [BRIGHT]

operation is disabled.

4. Press [ADJUST] to end adjustments. The display

is automatically closed after 10 seconds of

inaction.

• The unit loads set values when the power is turned

on. Changed values are automatically saved after

10 seconds.

User Data

You can save and load up to five combinations of menu settings and picture/volume adjustments as user data. You

can also return settings and adjustments to their factory defaults.

User data include the following settings.

• Menu settings except “SETUP LOAD/SAVE” and “CONTROL/CONTROL” (including button function settings on

the monitor front panel)

• Screen adjustments made in the picture/volume adjustments menu

Saving user data

Loading user data

1. Press [MENU] to display the MAIN menu.

2. Press [

] to select the “SYSTEM CONFIG”

2. Press [

] to select the “SYSTEM CONFIG”

menu and press [ENTER].

3. Press [

] to select the “SETUP SAVE” sub

3. Press [

] to select the “SETUP LOAD” sub

menu and press [ENTER].

The setting in the sub menu changes to green.

menu and press [ENTER].

The setting in the sub menu changes to green.

B.LIGHT/CONT.

BACKLIGHT

B.LIGHT/CONT.

BACKLIGHT

MENU POSITION

STATUS DISPLAY

SETUP LOAD

CENTER

3SEC OFF

FACTORY

USER1

LAST

MENU POSITION

STATUS DISPLAY

SETUP LOAD

CENTER

3SEC OFF

FACTORY

USER1

LAST

SETUP SAVE

POWER ON SETUP

POWER SAVE MODE

CALIBRATION

POWER ON SETUP

POWER SAVE MODE

CALIBRATION

OFF

Changes to green

4. Press [

] to select a “USER1” to “USER5”

4. Press [

] to select a “USER1” to “USER5”

file to save the settings to and press [ENTER].

file to load and press [ENTER].

The following screen appears.

To return to the factory defaults, select “FACTORY.”

5. Select “YES” and press [ENTER].

This saves the user data.

5. Select “YES” and press [ENTER].

This loads the user data.

To return to the previous screen

Push [MENU].

Main Menu

Menu configuration

MAIN MENU

SYSTEM

SIMUL

3D INPUT TYPE

SIMUL MODE

H MIRROR

LINE BY LINE

SIDE BY SIDE

LINE BY LINE

OVERLAY

H SHIFT

SDI1 (L)

SDI2 (R)

COMPARISON

MARKER

16:9

MARKER

VIDEO CONFIG ^*1

SYSTEM CONFIG

SMPTE-C (EX)

EBU (EX)

SMPTE-C

EBU

GAMMA SELECT

COLOR SPACE

COLOR TEMP.

SHARPNESS MODE

SHARPNESS H

SHARPNESS V

I-P MODE

4:3

B.LIGHT/CONT.

BACKLIGHT

BACK

CENTER

MENU POSITION

STATUS DISPLAY

SETUP LOAD

GPI PRESET1

GPI PRESET2

MARKER TYPE

CROSS HATCH

ITU-709

WIDE1

WIDE2

SETUP SAVE

WIDE3

MONO

POWER ON SETUP

POWER SAVE MODE

CALIBRATION

ANAMO

USER0-63

COLOR TEMP.

GAIN RED

GAIN BLUE

BIAS RED

BIAS BLUE

RESET

SD ASPECT

SCAN

D93

FUNCTION1

D65

FUNCTION ^*1

COLOR GAIN R

COLOR GAIN B

FUNCTION2

D56

FUNCTION3

VAR1

VAR2

VAR3

FUNCTION4

FUNCTION5

COLOR TEMP.

GAIN RED

GAIN BLUE

BIAS RED

BIAS BLUE

RESET

FUNCTION DISPLAY

GPI CONTROL

GPI1

GPI ^*1

GPI2

INPUT SELECT ^*1

VIDEO

GPI3

FORMAT

NTSC SETUP

SDI1

GPI4

GPI5

COLOR TEMP.

GAIN RED

GAIN BLUE

BIAS RED

BIAS BLUE

RESET

GPI6

AUTOSETUP

H POSITION

V POSITION

PHASE

SDI2

GPI7

YP^BPR/RGB

MODE

GPI8

COMPONENT LEVEL

SELECT SYNC

COMP.

CLOCK

WXGA/XGA

RESET

DVI-D

MODE

AUDIO

INPUT SELECT

EMBEDDED SELECT L

EMBEDDED SELECT R

LEVEL METER

CH SELECT

TWO WINDOW SIZE

SUB INPUT SEL.

TIME CODE

DISPLAY SETUP ^*1

CONTROL

POSITION

LOCAL ENABLE

FONT SIZE

0 dB POINT

OPERATION

LCD

HOURMETER

MODE SELECT

CLOSED CAPTION

MODE SELECT

CH INFO.

Menu items that cannot be selected when

the SYSTEM option is set to “2D”

*1 Setting values can be stored for both

2D and 3D.

Menu items that are not available without

being displayed when the SYSTEM option is

set to “3D”

Main Menu (continued)

Underlined values indicate factory defaults.

Sub menu

Setting

Description

SYSTEM

Switches between 2D and 3D

<2D>

<3D>

Sets monitor to work in 2D mode

Sets monitor to work in 3D (spectroscopic) mode

3D INPUT TYPE

SIMUL

Selects the input type in 3D mode.

3D ONLY

LINE BY LINE

SIDE BY SIDE

<SIMUL>

Uses the signals input from SDI1 and SDI2.

Ensure that the left-eye signal (L) is connected

to SDI1, and the right-eye signal is connected to

SDI2 (R).

When this input type is selected, the SIMUL

MODE noted below becomes active.

When SIMUL is selected the input signal from

SDI1 is used as the base and a phase difference

of up to 15 gs with the SDI2 input signal is

allowed.

Uses a signal with the left-eye and right-eye

signals split line by line.

The left-eye signal is displayed on the left hand

side of the screen, the right-eye signal on the

right side of the screen. A horizontally time

compressed signal is used for both.

SIMUL MODE

3D ONLY

LINE BY LINE

OVERLAY

SDI1(L)

Selects the display method when SIMUL is selected.

Displays in 3D (stereoscopic).

Mixes and displays the left-eye and right-eye

signals.

SDI2(R)

COMPARISON

<SDI1(L)>

<SDI2(R)>

Displays only the signal from SDI1

Displays only the signal from SDI2

Displays the signal input from SDI1 on the left

side of the screen, and the signal input from

SDI2 on the right side of the screen.

Both images are the same size and the aspect

ratio is 16:9. The MARKER function is

unavailable.

H MIRROR

3D ONLY

OFF

This option horizontally inverts the signal from SDI2 when “LINE BY

LINE” or “OVERLAY” is selected in SIMUL mode.

This can be used when checking left/right signals.

<OFF> Signal not inverted.

<ON>

Signal inverted.

3D ONLY

H SHIFT

128 - 127

Shifts the SDI2 signal horizontally when <LINE BY LINE> or

<OVERLAY> is selected in SIMUL mode.

(Factory

default: o)

The value of this setting is retained until the power is turned off. It is reset

to “0” when the power is turned off and then on again.

Main Menu (continued)

MARKER

Not available in the split-screen display of the “TWO WINDOW” function or COMPARISON in 3D mode. (CROSS

HATCH is not affected.)

Underlined values indicate factory defaults.

Sub menu

MARKER

Setting

OFF ^*1

Description

Turns the MARKER setting on and off.

<OFF>

<ON>

MARKER disabled

MARKER available

16:9 ^*2*3*4

OFF

Selects/displays the 16:9 marker type.

<OFF> No marker display

4:3

13:9

14:9

<4:3>

4:3 marker

<13:9>

13:9 marker

<14:9> 14:9 marker

<CNSCO>CNSCO marker

CNSCO

VISTA

95%

<VISTA> VISTA marker

<90%> 90% area marker

<95%>

<80%>

95% area marker

80% area marker

<93%> 93.1% area marker (TYPE1)

93% area marker (TYPE2)

<88%> 89.5% area marker (TYPE1)

88% area marker (TYPE2)

<USER> This area marker can be varied in 1% increments in the

range between 80% to 100%. However, an 88% value for a

TYPE1 MARKER TYPE indicates an area marker whose

height is 89% of available screen height in the selected

aspect ratio.

93%

90%

88%

80%

USER 85%

(The factory default is 85%.)

4:3 ^*2*4

OFF

Selects/displays the 4:3 marker type.

<OFF> No marker display

95%

93%

<95%> 95% area marker

<90%> 90% area marker

<93%>

<80%>

93% area marker

80% area marker

90%

88%

<88%> 89% area marker (TYPE1)

88% area marker (TYPE2)

80%

USER 85%

<USER> This area marker can be varied in 1% increments in the

range between 80% to 100%. Values of 93% and 88% for

TYPE1 MARKER TYPE indicate area markers whose height

is 93.1% and 89.5%, respectively, of available screen height

in the selected aspect ratio.

(The factory default is 85%.)

BACK ^*2

NORMAL

HALF

BLACK

Selects the background brightness around the marker.

<NORMAL> Normal background

<HALF>

50% background brightness

<BLACK>

0% background brightness (black)

CENTER ^*2

OFF

Displays/turns off the center marker.

<OFF>

<ON>

Turns the display off

Turns the display on

*1 This setting is turned “ON” when receiving marker control in REMOTE operation. (GPI, if set, has priority.)

*2 These settings are disabled when the GPI function (J page 53) is used to control the marker setting.

They are also disabled in split screen mode.

*3 This setting is enabled only for HD and SD signal input in 16:9 aspect ratio mode.

*4 TYPE1 and TYPE2 area marker size depends on the “MARKER TYPE” setting (J page 26).

Main Menu (continued)

Sub menu

Setting

Description

GPI PRESET1 ^*1

4:3

GPI PRESET1: Selects the marker displayed by the GPI terminal

“MARKER1 ON/OFF” (J page 53) operation.

GPI PRESET2: Selects the marker displayed by the GPI terminal

“MARKER2 ON/OFF” (J page 53) operation.

13:9

14:9

CNSCO

VISTA

<4:3>

4:3 marker

95% (16:9)

93% (16:9)

90% (16:9)

88% (16:9)

80% (16:9)

USER (16:9)

95% (4:3)

93% (4:3)

90% (4:3)

88% (4:3)

80% (4:3)

USER (4:3)

GPI PRESET2 ^*1

<13:9>

13:9 marker

14:9 marker

CNSCO marker

VISTA marker

<14:9>

<CNSCO>

<VISTA>

<95% (16:9)> 95% area marker for 16:9 aspect ratio

<93% (16:9)> 93% area marker for 16:9 aspect ratio

<90% (16:9)> 90% area marker for 16:9 aspect ratio

<88% (16:9)> 88% area marker for 16:9 aspect ratio

<80% (16:9)> 80% area marker for 16:9 aspect ratio

<95% (4:3)> 95% area marker for 4:3 aspect ratio

<93% (4:3)> 93% area marker for 4:3 aspect ratio

<90% (4:3)> 90% area marker for 4:3 aspect ratio

<88% (4:3)> 88% area marker for 4:3 aspect ratio

<80% (4:3)> 80% area marker for 4:3 aspect ratio

<USER>

Displays using the USER value of 16:9 / 4:3.

MARKER TYPE ^*2*3

CROSS HATCH

TYPE2

TYPE1

Selects conventional monitor or camera recableer marker size.

<TYPE2>

<TYPE1>

Marker size compliant with the camera recorder

(Panasonic)

The marker has the same size as that of the previous

model (BT-LH2600W).

OFF

Turns the cross hatch grid on and off and sets its density.

LOW

HIGH

<OFF>

<LOW>

Turns the display off

20/256 gradations (displays a light cross hatch grid)

<HIGH> 70/256 gradations (displays a dense cross hatch grid)

*1 Remote control via RS-232C ends in error (error response: ER001) when “GPI PRESET1” or “GPI PRESET2”

is selected with the GPI function.

*2 TYPE1 and TYPE2 area marker size depends on the “MARKER TYPE” setting.

*3 Display size for SD signals differ.

TYPE1: The effective horizontal area meets the SMPTE125M for NTSC and ITU-R BT. 601-5 for PAL.

TYPE2: The effective horizontal area meets the EIA-RS170A for NTSC and ITU-R BT. 470-4 for PAL.

Main Menu (continued)

Marker types

_16:9 marker

_4:3 marker

(Displayed for HD input and SD input in 16:9 ratio

mode.)

(Displayed for SD input in 4:3 aspect ratio mode)

This marker is displayed as a dotted line.

This marker is only displayed as a vertical bar. The

section becomes the “MARKER BACK”.

95% Area marker

90% Area marker

80% Area marker

93% Area marker

88% Area marker

4:3 marker

13:9 marker

14:9 marker

VISTA marker, CNSCO marker

This marker is displayed as a horizontal dotted line.

(Displayed for HD input and SD input in 16:9 ratio mode.)

This marker is displayed as a dotted line.

VISTA marker

CNSCO marker

The marker is displayed as a vertical dotted line

when “UNDER” is selected under “SCAN” in the

“VIDEO CONFIG” menu.

95% Area marker

90% Area marker

80% Area marker

93% Area marker

TYPE1 Vertical 89%,

horizontal 88%

TYPE2 Vertical/Horizontal 88%

VISTA marker

Area marker

This marker is displayed as a dotted line.

CNSCO marker

88% Area marker

100% Area marker

TYPE1 Vertical 93.1%,

horizontal 93%

TYPE2 Vertical/Horizontal 93%

USER area marker ^*1

• You can display the 4:3 marker and the 16:9

95% Area marker

90% Area marker

80% Area marker

93% Area marker

marker simultaneously.

Simultaneous display example

TYPE1 Vertical 89.5%,

horizontal 88%

TYPE2 Vertical/Horizontal 88%

The

section becomes the “MARKER BACK”. It controls

the background of the marker selected with a 16:9 ratio.

16:9 marker:

95% area marker

4:3 marker:

4:3 marker

88% Area marker

16:9 marker

80% area marker

100% Area marker

_Center marker

Center marker

This marker is displayed

at the center of the

screen.

USER area marker *¹

*1 Use the

and

buttons to increase or decrease the

area marker in 1% increments in the range between 80

and 100%.

Main Menu (continued)

_“CROSS HATCH”

The “CROSS HATCH” function enables display of markers at regular vertical and horizontal intervals to facilitate

composition and other tasks. The width of marker lines is 1 dot, the markers consist of 1 line, and are spaced

120 dots apart (fixed value).

Each press of the button (“FUNCTION1” to “FUNCTION5”) to which the “CROSS HATCH” has been assigned

turns the function on and off.

Note:

The CROSS HATCH signal displays vertical lines at intervals of 6% of the width of the screen.

Each press of the FUNCTION button to which the “CROSS HATCH” function is assigned changes the

display as shown.

HD/SD (16:9) mode

1st press

2nd press

Light cross hatch

Dense cross hatch

SD (4:3) mode

3rd press (back to original image without cross hatch)

Main Menu (continued)

VIDEO CONFIG

Underlined values indicate factory defaults.

Sub menu

GAMMA

SELECT ^*1*2

Setting

Description

Selects gamma curve. The gamma curve in the sub-window can be

set in the split-screen display and sub-window display (single screen)

of the “TWO WINDOW” function.

STANDARD

STDIO/PST

FILM

<STANDARD>Standard mode

<STDIO/PST>Color emphasis mode (a mode that approximates CRT

display capability suitable for studio or postproduction

application)

<FILM>

Film mode (For VARICAM use)

The

mark appears at the top left of the screen when “FILM” is

selected.

COLOR SPACE

*7*8

Sets the color space. The color space in the sub-window can be set in

the split-screen display and sub-window display (single screen) of the

“TWO WINDOW” function.

SMPTE-C (EX)

EBU (EX)

SMPTE-C

EBU

ITU-709

WIDE1

WIDE2

WIDE3

<SMPTE-C (EX)> Redness changed from <SMPTE-C> mode. ^*9

<SMPTE-C> SMPTE-C standard

Redness changed from <EBU> mode. ^*9

<EBU>

EBU standard

<ITU-709>

<WIDE1>

ITU-R BT. 709 standard

Sets the gamma curve to 2.2 in wide color gamut (using

Adobe color space) mode.

<WIDE2>

<WIDE3>

Sets the gamma curve to 1.8 in wide color gamut (using

Adobe color space) mode.

Sets the gamma curve to 2.6 in wide color gamut (using

D-Cinema color space) mode.

USER0 - 63 ^*5*6

D93 ^*6

COLOR TEMP.

Selects color temperature. Both the main window and sub-window can

be set up in the split-screen display of the “TWO WINDOW” function.

<USER 0 - 63> Adjustable settings 0 - 63 (equivalent to a color

temperature range of 3,000 - 9,300K)

<D93> Equivalent to a color temperature of 9,300K

<D65> Equivalent to a color temperature of 6,500K

D65 ^*6

D56 ^*6

VAR1

VAR2

VAR3

<D56> Equivalent to a color temperature of 5,600K

<VAR1> WB adjustment mode ^*4<VAR2> WB adjustment mode ^*4

<VAR3> WB adjustment mode ^*4

USER20 is approximately 5,000 K and USER33 is approximately 6,300 K.

HIGH ^*3

LOW

SHARPNESS

MODE ^*2

Selects the width of outline correction edge. Both the main window

and sub-window can be set up in the split-screen display of the “TWO

WINDOW” function.

<HIGH> Thin edge

*1 Changes are not reflected to a still image in the main window in the split-screen display of the “TWO WINDOW” function.

*2 These functions are not available when “RGB-COMP.” under “YPB R/RGB” or “DVI-COMP.” under “DVI-D” is selected in

the “INPUT SELECT” menu ( page 40). The gamma curve is set to STANDARD when “RGB-COMP.” or “DVI-COMP.”

<LOW> Wide edge

is selected. Selecting WIDE1 to 3 for “COLOR SPACE” produces the gamma curve fixed to that “COLOR SPACE.”

*3 The following sharpness values are available and the settings for the selected input signal is displayed.

Adjustment status during selection appears at the bottom right of the screen.

1) VIDEO system input (VIDEO) (the factory defaults are SHARPNESS MODE: LOW)

2) HD for any other input (the factory defaults are SHARPNESS MODE: HIGH).

3) SD for any other input (the factory defaults are SHARPNESS MODE: LOW).

*4 Selecting “VAR1”, “VAR2” and “VAR3” engages the WB adjustment mode (J page 31).

*5 Procedure for selecting USER 0 - 63:

1) Press [ENTER] (“USER” changes to blue).

2) Use [

] to select 0 - 63 and press [ENTER].

*6 An asterisk (*) is displayed after the color temperature value in 3D mode. (Example display: D65*) This

indicates that it is an adjusted value for when using 3D Polarized Eyewear.

*7 Factory default setting: SMPTE-C (U.S.A. and Canada), EBU (other countries)

*8 The SDI1 signal and SDI2 signal (displayed when “COMPARISON” is selected in SIMUL MODE) are set to the

same color space.

*9 As the red reproduction of this monitor is truer to the original than previous models (exc. BT-LH2550) red

appears darker. Used when rendering colors that have a softer shade of red.

Main Menu (continued)

Sub menu

Setting

Description

Sets horizontal outline correction. The item display moves to the lower

part of the screen during adjustment. Both the main window and sub-

window can be set up in the split-screen display of the “TWO

WINDOW” function.

0 - 30

SHARPNESS H

SHARPNESS V

Sets vertical outline correction. The item display moves to the lower

part of the screen during adjustment. Both the main window and sub-

window can be set up in the split-screen display of the “TWO

WINDOW” function.

0 - 30

2D ONLY

I-P MODE ^*1*2

2D ONLY

MODE2

MODE1

Selects IP conversion mode. (J page 30, “IP mode”) Both the main

window and sub-window can be set up in the split-screen display of

the “TWO WINDOW” function.

<MODE2> Inter-field interpolation

<MODE1> Inter-frame interpolation

MONO ^*1

OFF

Switches between color and monochrome (MONO).

<OFF> Color

<ON> Monochrome

• When ON, the CHROMA setting of the picture/volume adjusting menu

is fixed at 0.

ANAMO ^*1*3

2D ONLY

OFF

With an Anamo lens and HD-SDI input, the picture is resized to

Anamo magnification (the vertically enlarged signal can be vertically

compressed and corrected for display). Can be set in the split screen

display of the “TWO WINDOW” function, but operation is disabled.

SD ASPECT ^*1

2D ONLY

4:3

16:9

Sets the aspect ratio for SD signal input. Can be set in the split screen

display of the “TWO WINDOW” function, but operation is disabled.

<4:3> 4:3 display

<16:9> 16:9 display

SCAN ^*1

2D ONLY

NORMAL

UNDER

Sets under-scan and normal display. Can be set in the split screen

display of the “TWO WINDOW” function, but operation is disabled.

<NORMAL> Normal display

<UNDER> Under-scan

COLOR GAIN R

COLOR GAIN B

0 - 30

This fine tunes the GAIN of the R component. The R component of the

sub-window can be set in the split-screen display and sub-window

display (single screen) of the “TWO WINDOW” function in 2D mode. In

3D mode (COMPARISON), the R component of SDI2 (R) can be set.

0 - 30

This fine tunes the GAIN of the B component. The B component of the

sub-window can be set in the split-screen display and sub-window

display (single screen) of the “TWO WINDOW” function in 2D mode. In

3D mode (COMPARISON), the B component of SDI2 (R) can be set.

*1 These functions are not available when “RGB-COMP.” under “YPBPR/RGB” or “DVI-COMP.” under “DVI-D” is

selected in the “INPUT SELECT” menu (J page 40).

*2 To use the “TWO WINDOW” (J page 44) function,

1) Change settings after exiting the “TWO WINDOW” function.

2) It is recommended to use “MODE2” for handling fast video.

*3 “SCAN” changes are not reflected in Anamo size display.

IP mode

“MODE1” performs IP conversion using inter-frame interpolation.

The factory default is “MODE1”.

“MODE2” performs IP conversion using inter-field interpolation.

Since interpolation is performed inside each field, this mode is suitable for checking interlace status.

Main Menu (continued)

_ WB adjustment mode

Select “VAR1” to “VAR3” for “COLOR TEMP.” in the “VIDEO CONFIG” menu to make “WHITE BALANCE VAR1”

to “WHITE BALANCE VAR3” (WB) adjustments.

Underlined values indicate factory defaults.

Sub menu

Settings

Description

COLOR TEMP. ^*1

USER 0 - 63

D93 *³

Selects the color temperature that will become the basis

for adjustment.

<USER 0 - 63> Adjustable settings 0 - 63 (equivalent

to a color temperature range of 3,000 -

9,300K)

D65 *³

D56 *³

<D93> Equivalent to a color temperature of 9,300K

<D65> Equivalent to a color temperature of 6,500K

<D56> Equivalent to a color temperature of 5,600K

USER20 is approximately 5,000 K and USER33 is

approximately 6,300 K.

Adjusts the GAIN elements for RED. ^*2

GAIN RED

0 - 1023

(Factory defaults are color

temperature <D65>

values.)

•These are the adjustments

made before shipment from

the factory.

Adjusts the GAIN elements for BLUE. ^*2

GAIN BLUE

BIAS RED

BIAS BLUE

RESET

-512 - 511

(Factory default: 0)

Adjusts the BIAS elements for RED. ^*2

Adjusts the BIAS elements for BLUE. ^*2

Resets “GAIN RED” - “BIAS BLUE” to color temperature

values selected under “COLOR TEMP.”

*1 Selecting “COLOR TEMP.” and pressing [ENTER] after making a change, opens a confirmation screen.

Selecting “YES” and pressing [ENTER] in this screen resets selected GAIN and BIAS values to the selected

color temperature values.

*2 The item display moves to the lower part of the screen during adjustment.

*3 An asterisk (*) is displayed after the color temperature value in 3D mode. (Example display: D65*) This

indicates that it is an adjusted value for when using 3D Polarized Eyewear.

Main Menu (continued)

SYSTEM CONFIG

Underlined values indicate factory defaults.

Sub menu

Settings

Description

B.LIGHT/CONT.

BACKLIGHT

CONTRAST

Selects function to be assigned to BACKLIGHT/CONT. in the picture/

volume adjusting menu.

<BACKLIGHT> Adjusts the BACKLIGHT.

<CONTRAST> Adjusts the CONTRAST.

BACKLIGHT

0 - 50 - 60

Adjusts the backlight when the B.LIGHT/CONT. submenu is set to

CONTRAST.

POSITION

CENTER

Positions the on-screen menu.

<LB>

Center of the screen

Left Bottom

Right Bottom

Right Top

<RB>

<RT>

<LT>

Left Top

STATUS

DISPLAY

OFF

Sets display state for input signal status (on-screen menu).

3SEC OFF

<OFF>

Not displayed.

CONTINUE

<3SEC OFF>

Displayed for 3 seconds after a status change.

Displayed at all times

USER5 ^*1*2

USER4 ^*1*2

USER3 ^*1*2

USER2 ^*1*2

USER1 ^*1*2

FACTORY

Loads saved factory defaults (FACTORY) or user data (USER1 - USER5).

After loading user data, the screen displays the signal selected before

user data was loaded.

SETUP LOAD

SETUP SAVE

USER5 ^*2

USER4 ^*2

USER3 ^*2

USER2 ^*2

USER1 ^*2

Up to 5 sets of user data can be saved (J page 22).

They save menu settings and adjustments made in the picture/volume

adjusting menu (PHASE/CHROMA/BRIGHT/CONTRAST/BACKLIGHT)

except “SETUP SAVE/SETUP LOAD.”

POWER ON

SETUP

USER5

USER4

USER3

USER2

USER1

FACTORY

LAST

Selects the settings used when the power is turned on.

<LAST>

Starts in the mode used when the power was last turned

off.

<FACTORY> Starts up using the factory defaults.

<USER1 - 5> Starts up using USER registered settings.

POWER SAVE

MODE

OFF

Sets the power save mode

<OFF> Does not activate the POWER SAVE mode.

<ON> The backlight dims when no signal (NO SIGNAL) is input for 60

seconds or longer. Signal input or menu operation will return the

backlight to its normal brightness.

CALIBRATION

Connect a CA-210 color analyzer and use this submenu to make a

calibration. It also returns calibration data to factory defaults. (J page 33,

34)

*1 When the monitor is shipped, settings for “USER1” - “USER5” are identical to “FACTORY.”

*2 “H SHIFT” (J page 24), “H POSITION”, “V POSITION”, “PHASE” and “CLOCK” (J page 41) cannot be saved

or loaded.

*3 So that there is no confusion with 2D mode when working in 3D mode, STATUS DISPLAY will display

information as per the “CONTINUE” setting even if “3SEC OFF” is selected.

Main Menu (continued)

_CALIBRATION

The CALIBRATION function in this unit measures LCD panel characteristics from low to high brightness values

and internal monitor processing handles CALIBRATION.

CALIBRATION does not rely on image quality settings since internal signals are used for a calibration.

CALIBRATION in this unit is made at D65 color temperature and calibrations for other color temperatures are

results calculated from this value.

_Equipment required for calibration

• Konica Minolta CA-210 display color analyzer

• Konica Minolta CA-PU12 or CA-PU15 standard measurement probe

• RS-232C cable (male to male, straight)

• Connect the RS-232C terminal on this unit to the RS-232C terminal on the CA-210 display color analyzer using a

straight cable.

CA-210 side

(Straight)

BT-3DL2550P/E Side

Pin number

Signal

Pin number

Signal

N.C.

TXD

RXD

DSR

GND

DTR

CTS

RTS

N.C.

RXD

TXD

DTR

GND

DSR

RTS

CTS

GND

This unit

Konica Minolta CA-PU12 or CA-PU15

standard measurement probe

Konica Minolta CA-210 display

color analyzer

RS-232C cable

• Be sure to set the following calibration values on the CA-210 display color analyzer. The analyzer will not produce

a correct calibration unless it has been calibrated. For details on setup procedures, refer to the CA-210 User's

Guide.

Calibration

0.3091

0.3429

195.3

0.6759

0.3126

47.56

0.2029

0.691

135.2

0.1495

0.0587

13.21

• Turn on this unit and perform adequate aging (about 1 hour) before starting calibration.

• Turn off the lights in the room and make sure that no external light can enter the standard measurement probe

before starting the calibration. External light that enters the probe will prevent correct calibration of low brightness

characteristics.

• LCD panel characteristics and instrument error in the display color analyzer may sometimes result in small

differences in values after calibration.

In a fine tuning of the monitor, also set GAIN and BIAS for R and B in the COLOR TEMP. VAR mode. The GAIN

and BIAS values for G cannot be altered.

• Do not place 3D Polarized Eyewear between the analyzer and the monitor during calibration.

Main Menu (continued)

_CALIBRATION

Select CALIBRATION in the “SYSTEM CONFIG” menu to open the following menus.

Sub menu

Setting

Description

AUTO CALIBRATION

Connect a CA-210 color analyzer and use this submenu to make a

calibration.

Select “AUTO CALIBRATION” and select “YES” in the

confirmation screen that appears to start calibration.

RESET ^*2

Returns calibration data to their factory defaults.

Select “RESET” and select “YES” in the confirmation screen that

appears to return calibrated values to their factory defaults.

*1 “EXECUTING” is displayed during “AUTO CALIBRATION” and “COMPLETE” appears when calibration ends.

“INCOMPLETE” appears if calibration could not be completed.

*2 When “RESET” ends, “COMPLETE” appears.

Performing AUTO CALIBRATION

1. Press [ ] in the “SYSTEM CONFIG” menu,

RESET operation

1. Press [ ] in the “SYSTEM CONFIG” menu,

select the [CALIBRATION] submenu and press

[ENTER].

select the [CALIBRATION] submenu and press

[ENTER].

2. Press [

], select the [AUTO CALIBRATION]

2. Press [

], select the [RESET] submenu and

submenu and press [ENTER].

press [ENTER].

[AUTO CALIBRATION]

[RESET]

3. Select “YES” and press [ENTER].

This starts calibration.

This resets the setting of this monitor.

[AUTO CALIBRATION]

[RESET]

xxxxxxxx indicates that one of the following

messages with the meaning listed below appears.

EXECUTING: Operation in progress

xxxxxxxx indicates that the following message with

the meaning listed below appears.

COMPLETE: Operation completed

INCOMPLETE: Operation did not complete.

(Check RS-232C cable connection.)

Main Menu (continued)

FUNCTION

Underlined values indicate factory defaults.

Sub menu

Settings

Description

FUNCTION 1 -

FUNCTION 5

Selects functions to be assigned to [FUNCTION1] - [FUNCTION5]

(front panel buttons).

Displays synchronizing signals (horizontal, vertical).

The display changes in the following order.

HV DELAY

AUTOSETUP

BLUE ONLY

GAMMA SELECT

COLOR SPACE

SD ASPECT

SCAN

2D ONLY

DELAY OFF J H DELAY J V DELAY J HV DELAY J DELAY OFF

2D ONLY

Performs auto setup for PC display.

TWO WINDOW

SUB INPUT SEL.

MARKER

LEVEL METER

CROSS HATCH

MONO

TIME CODE

CLOSED

CAPTION

Cuts the red and green signals. Use this function to check phase and

chroma. This button toggles between ON and OFF.

<GAMMA SELECT>^*1

Displays the gamma curve.

The display changes in the following order.

GAMMA STANDARD J GAMMA FILM J GAMMA STDIO/PST J

GAMMA STANDARD

Sets the color space. The display changes in the following order.

EBU J ITU-709 J WIDE1 J WIDE2 J WIDE3 J SMPTE-C (EX)J

EBU (EX) J SMPTE-C J EBU

ANAMO

3D INPUT TYPE

SIMUL MODE

H MIRROR

UNDEF

2D ONLY

Switches between “16:9” and “4:3.” ^*1

2D ONLY

<SCAN>

Switches between “UNDER SCAN” and “NORMAL SCAN”. ^*1

2D ONLY

Sets the split-screen function.^*1

(Factory

The display changes in the following order.

• When the input signal terminals of video displayed in the sub-window

and main window differ

SINGLE MAIN J TWO (L/S, M/M, S/L) J SINGLE SUB J SINGLE

MAIN

• When video from the same input signal terminal is displayed in the

sub-window and main window

SINGLE MAIN J TWO(L/S, M/M, S/L) J STILL J SINGLE SUB J

SINGLE MAIN

defaults, same in

2D mode and 3D

mode)

FUNCTION1:

MARKER

FUNCTION2:

CROSS

HATCH

2D ONLY

FUNCTION3:

BLUE ONLY

FUNCTION4:

TIME CODE

FUNCTION5:

LEVEL METER

Switches sub-window inputs in split screen mode.

Turns the marker on and off.

Turns the LEVEL METER display on and off.

Turns the time code display on and off.

<MONO>

Switches between color and monochrome.

2D ONLY

Turns the closed caption display on and off.

2D ONLY

<ANAMO>

Turns ANAMO on and off.

*1 Changes in settings change menu settings.

Main Menu (continued)

Sub menu

Settings

Description

FUNCTION 1 -

FUNCTION 5

3D ONLY

3D INPUT TYPE>

Selects the input type in 3D mode.

SIMUL J LINE BY LINE J SIDE BY SIDE

3D ONLY

SIMUL MODE

Selects the display method in “SIMUL” mode.

LINE BY LINE J OVERLAY J SDI1(L) J SDI2(R) J

COMPARISON

3D ONLY

H MIRROR>

Selects whether to shift the SDI2 signal horizontally in “SIMUL” mode.

ON J OFF

<UNDEF>

Undefined

FUNCTION

DISPLAY

Selects display of functions assigned to [FUNCTION1] -

[FUNCTION5] (front panel buttons). It also selects button action (1-

touch, 2-touch, off).

<ON1>

OFF

ON1

ON2

1-touch action to display and perform functions.

<ON2>

2-touch action to display and perform functions.

<OFF>

No function display.

Main Menu (continued)

_FUNCTION setting restrictions

Settings are not available under the following conditions.

Setting

Conditions that disable operation

HV DELAY

2D ONLY

In TWO WINDOW mode, “INVALID FUNCTION” appears to indicate that operation is disabled.

When “RGB-COMP.” is selected under “YPBPR/RGB” or “DVI-COMP.” is selected under

“DVI-D” in the “INPUT SELECT” menu, “INVALID FUNCTION” appears to indicate that

operation is disabled.

AUTO SETUP

2D ONLY

When something other than “RGB-COMP.” is selected under “YPBPR/RGB” in the “INPUT

SELECT” menu, “NOT RGB-COMP. CH” appears to indicate that operation is disabled.

When “RGB-COMP.” is selected under “YP^BPR/RGB” in the “INPUT SELECT” menu and

no signal is input, “INCOMPLETE” appears to indicate that operation is disabled.

GAMMA SELECT

When GPI is set, “INVALID FUNCTION” appears to indicate that operation is disabled.

When “RGB-COMP.” is selected under “YP^BPR/RGB” or “DVI-COMP.” is selected under

“DVI-D” in the “INPUT SELECT” menu, “INVALID FUNCTION” appears to indicate that

operation is disabled.

When “WIDE1” to “WIDE3” is selected under COLOR SPACE, “INVALID FUNCTION”

appears to indicate that operation is disabled.

SD ASPECT

2D ONLY

When GPI is set, “INVALID FUNCTION” appears to indicate that operation is disabled. In

TWO WINDOW mode and HD signal display, “INVALID FUNCTION” appears to indicate

that operation is disabled.

2D ONLY

SCAN

When GPI is set, “INVALID FUNCTION” appears to indicate that operation is disabled.

In TWO WINDOW mode, “INVALID FUNCTION” appears to indicate that operation is disabled.

TWO WINDOW

2D ONLY

When “RGB-COMP.” is selected under “YPBPR/RGB” or “DVI-COMP.” is selected under

“DVI-D” in the “INPUT SELECT” menu, the display toggles between single screen display

of the main window and sub-window. When WINDOW SIZE is something other than M/M,

the SINGLE MAIN and SINGLE SUB screens appear alternately, but no still image screen

appears. When the input signal terminals of video displayed in the main window and sub-

window differ, the SINGLE MAIN and SINGLE SUB windows appear alternately, but no

still image screen appears.

MARKER

When “RGB-COMP.” is selected under “YP^BPR/RGB” or “DVI-COMP.” is selected under

“DVI-D” in the “INPUT SELECT” menu, “INVALID FUNCTION” appears to indicate that

operation is disabled.

When GPI is set during TWO WINDOW operation, “INVALID FUNCTION” appears to

indicate that operation is disabled.

LEVEL METER

If input is something other than SDI input or if “INPUT SELECT” of the “AUDIO” menu is

set to “ANALOG”, “INVALID FUNCTION” appears to indicate that operation is disabled.

MONO

When GPI is set, “INVALID FUNCTION” appears to indicate that operation is disabled.

TIMECODE

When input is something other than HD-SDI input, “INVALID FUNCTION” appears to

indicate that operation is disabled.

2D ONLY

ANAMO

When input is something other than HD-SDI signal input, “INVALID FUNCTION” appears

to indicate that operation is disabled.

SIMUL MODE

3D ONLY

“INVALID FUNCTION” is displayed to indicate operation is disabled except when 3D mode

is set to SIMUL.

H MIRROR

3D ONLY

“INVALID FUNCTION” is displayed to indicate operation is disabled except when 3D mode

is set to SIMUL.

This function is only available when SIMUL MODE is set to LINE BY LINE or OVERLAY. It

is not available when SIMUL MODE is set to SDI1 (L), SDI2 (R), or COMPARISON.

Main Menu (continued)

_Functions and operating status displayed on screen when FUNCTION buttons are pressed

Pressing any of the [FUNCTION1] to [FUNCTION5] buttons displays the operations assigned to each button as

shown below.

• HV DELAY

• MARKER

MARKER OFF, 4:3 MARKER, 13:9 MARKER,

DELAY OFF, H DELAY, V DELAY, HV DELAY

• AUTOSETUP

14:9 MARKER, VISTA MARKER,

CNSCO MARKER, 95% MARKER, 93% MARKER,

90% MARKER, 88% MARKER, 80% MARKER,

××% MARKER (××% indicates an 80 to 100%

USER setting),

COMP.AUTOSETUP, COMPLETE, INCOMPLETE,

NOT RGB-COMP.CH

• BLUE ONLY

BLUE ONLY ON, BLUE ONLY OFF

• GAMMA SELECT

MARKER ON

16:9 MARKER value / 4:3 MARKER value ^*1

• LEVEL METER

METER OFF, METER 2CH, METER 4CH,

METER 8CH

• CROSS HATCH

CROSS HATCH HIGH, CROSS HATCH LOW,

CROSS HATCH OFF

• MONO

MONO ON, MONO OFF

• TIME CODE

LTC, VITC, LUB, VUB, TC OFF

• CLOSED CAPTION

GAMMA STANDARD, GAMMA FILM,

GAMMA STDIO/PST

• COLOR SPACE

COLOR SPACE SMPTE-C (EX),

COLOR SPACE EBU (EX),

COLOR SPACE SMPTE-C, COLOR SPACE EBU,

COLOR SPACE ITU-709, COLOR SPACE WIDE1,

COLOR SPACE WIDE2, COLOR SPACE WIDE3

• SD ASPECT

4:3, 16:9

• SCAN

NORMAL SCAN, UNDER SCAN

• TWO WINDOW

CC1, CC2, CC3, CC4, CC OFF

• ANAMO

ANAMO ON, ANAMO OFF

• 3D INPUT TYPE

SINGLE MAIN, TWO L/S, TWO M/M, TWO S/L,

STILL, SINGLE SUB

• SUB INPUT SEL.

VIDEO, SDI1, SDI2, YP^BPR/RGB, DVI-D

SIMUL, LINE BY LINE, SIDE BY SIDE

• SIMUL MODE

LINE BY LINE, OVERLAY, SDI1(L), SDI2(R),

COMPARISON

• H MIRROR

MIRROR ON, MIRROR OFF

*1 When both 16:9 and 4:3 are set in the marker setting, the 16:9 value is displayed in the first half, and the 4:3 is

displayed in the second half.

_Functions displayed only when in 2D or 3D mode

Certain functions displayed when the FUNCTION button is pressed are only displayed in 2D or 3D mode.

• Functions not displayed in 3D mode.

HV DELAY, AUTOSETUP, TWO WINDOW, SD ASPECT, SCAN, SUB INPUT SEL, CLOSED CAPTION,

ANAMO

• Functions not displayed in 2D mode.

3D INPUT TYPE, SIMUL MODE, H MIRROR

2D ONLY

_“HV DELAY”

This displays the blanking period. Each press of the button changes the display as follows: “H blanking display”

J “V blanking display” J “H and V blanking display” J “no blanking display.”

Main Menu (continued)

GPI

“GPI CONTROL” is used to enable and disable GPI functions and assign functions to each of the GPI terminal pins

(J page 53).

Underlined values indicate factory defaults.

Sub menu

Settings

Description

GPI CONTROL

DISABLE

ENABLE

Enables and disables GPI functions

<DISABLE> Disabled

<ENABLE> Enabled

GPI1 - GPI8

UNDEF

Assigns functions to the GPI control terminal pins.

The same items can be set to each terminal (J page

53).

MARKER1 ON/OFF

MARKER2 ON/OFF

MARKER BACK HALF

MARKER BACK BLACK

CENTER MARKER

INPUT SEL. VIDEO

2D ONLY

INPUT SEL. SDI1

INPUT SEL. SDI2

INPUT SEL.

2D ONLY

YP^BPR/RGB

INPUT SEL. DVI-D

2D ONLY

SD ASPECT

2D ONLY

SCAN

R-TALLY

G-TALLY

MONO

GAMMA SEL. FILM

GAMMA SEL.

STDIO/PST

2D ONLY

SELECT SYNC

Note:

This function is not available when,

• “SD ASPECT” operation when input signal is HD or PC

• “SCAN” operation when the input signal is PC

• “GAMMA SELECT” operation when the input signal is PC

• “SELECT SYNC” operation when anything other than “RGB-VIDEO” is selected under “YP^BPR/RGB” in the

“INPUT SELECT” menu

• “MONO” operation when input signal is PC

• “INPUT SEL.SDI1”, “INPUT SEL.SDI2” operations when 3D mode is set to SIMUL

Main Menu (continued)

INPUT SELECT

Underlined values indicate factory defaults.

Sub menu

Settings

Description

2D ONLY

OFF

Turns VIDEO line to the INPUT button on/off. ^*1

VIDEO

AUTO

NTSC

PAL

Selects the video input format. ^*2

<AUTO> Automatically selects NTSC or PAL.

<NTSC> NTSC

FORMAT

2D ONLY

<PAL> PAL

Selects NTSC setup level.

NTSC SETUP

2D ONLY

<75>

Select this function when using 7.5% setup signals.

(Adjusts the interior of the monitor to the 7.5% setup

level to suit the black level)

<00>

Select this when there is no setup signal.

SDI1 ^*3

SDI2 ^*3

OFF

Turns SDI1 line to the INPUT button on/off. ^*1

OFF

Turns SDI2 line to the INPUT button on/off. ^*1

OFF

Turns YPB

/RGB line to the INPUT button on/off. ^*1

YPBPR/RGB

2D ONLY

YPBPR

RGB-VIDEO

RGB-COMP.

Selects YP^BPR (component) or RGB input mode.

<YP^BPR> Selects the YPBPR signal.

<RGB-VIDEO> Selects the video RGB signal.

<RGB-COMP.> Selects the PC RGB signal.

MODE

COMPONENT

SMPTE

B75

Selects YPBPR (component) signal input level.

2D ONLY

<SMPTE>

Signal level complies with SMPTE and PB and PR are

LEVEL

B00

0.7 V [p-p] at 100% chroma.

<B75>

Select this when connecting a Betacam or similar

device with a setup function. (Adjusts the interior of the

monitor to the 7.5% setup level to suit the black level)

Select this when connecting a Betacam or similar

device without a setup function.

<B00>

INT

Selects the sync signal when using YP^BPR and RGB-VIDEO input.

SELECT SYNC

EXT

<INT>

Select when the synchronizing signal is superimposed

on the G or Y signal.

2D ONLY

<EXT>

Select to synchronize with an external synchronizing

signal.

2D ONLY

Performs analog PC settings. (“COMP.” J page 41)

COMP.

DVI-D ^*3

OFF

Turns DVI-D line to the INPUT button on/off. ^*1

MODE

DVI-VIDEO

DVI-COMP.

Selects DVI-D input mode.

<DVI-VIDEO> Selects the RGB signal input of RGB video.

<DVI-COMP.> Selects PC input.

*1 All five input lines (VIDEO, SDI1, SDI2, YP^BPR/RGB, DVI-D) cannot be turned off. An attempt to turn off all

inputs ends when the fourth input line is turned off since it will not be possible to turn off the 5th input line also.

*2 “AUTO” is the factory default, but select a specific format when there is risk that the input signal may be

contaminated by outside noise.

*3 When 3D mode is set to SIMUL, the SDI1 and SDI2 lines are selected regardless of the OFF/ON setting.

Main Menu (continued)

2D ONLY

_COMP.

Set “RGB-COMP” under “YPBPR/RGB” in the “INPUT SELECT” menu and select the “RGB-COMP.” input line to

enable the “COMP” menu.

Underlined values indicate factory defaults.

Sub menu

Settings

Description

AUTOSETUP ^*1

2D ONLY

Automatically adjusts RGB-COMP. as well as H POSITION,

V POSITION, PHASE and CLOCK settings of input formats.

Selecting this submenu opens a confirmation screen and

setup starts after choosing “YES” in this screen.

0 - 30 - 60

0 - 16 - 60

Adjusts horizontal image display position. ^*2

H POSITION

2D ONLY

Adjusts vertical image display position. ^*2

V POSITION

2D ONLY

Adjusts the clock phase in 1/32 clock period increments. ^*2

Adjusts the sampling clock in dot units. ^*2

PHASE

2D ONLY

700 - 2200

CLOCK

(Factory preset settings:^*3)

XGA

Switches between XGA (UXGA) and WXGA (WUXGA).

WXGA/XGA

WXGA

2D ONLY

Returns “H POSITION”, “V POSITION”, “PHASE” and

“CLOCK” settings in the RGB COMP. input compliant

format to their factory defaults.

RESET

*1 Run “AUTOSETUP” when video is displayed across the entire screen area. If video is distorted, run

“AUTOSETUP” after executing “RESET”. “EXECUTING” is displayed during “AUTOSETUP” and “COMPLETE”

appears when setup completes.

“INCOMPLETE” is displayed if setup could not be completed.

AUTOSETUP may not provide adequate adjustment for some video input. Use H POSITION, V POSITION,

PHASE and CLOCK to adjust.

*2 Each input format can be adjusted but not when user data is loaded (“SETUP LOAD” J page 32) or saved

(“SETUP SAVE” J page 32).

*3 “CLOCK” factory default

FORMAT

640 × 400 (70 Hz)

640 × 480 (60 Hz)

640 × 480 (75 Hz)

640 × 480 (85 Hz)

800 × 600 (60 Hz)

800 × 600 (70 Hz)

800 × 600 (75 Hz)

800 × 600 (85 Hz)

1024 × 768 (60 Hz)

CLOCK

800

FORMAT

CLOCK

1328

1312

1376

1648

1680

1712

1688

2160

2080

1024 × 768 (70 Hz)

1024 × 768 (75 Hz)

1024 × 768 (85 Hz)

1280 × 768 (50 Hz)

1280 × 768 (60 Hz)

1280 × 768 (75 Hz)

1280 × 1024 (60 Hz)

1600 × 1200 (60 Hz)

1920 × 1200 (60 Hz)

800

840

832

1056

1040

1056

1048

1344

Main Menu (continued)

AUDIO

Use the following submenus to set headphone output and audio level meters.

Underlined values indicate factory defaults.

Sub menu

Settings

Description

INPUT

SELECT

AUTO

ANALOG

Selects input line for audio output to headphone terminal.

However, when 3D mode is set to SIMUL the selection in this menu is

applied to the audio signal input from the SDI1 terminal.

<AUTO>

When an SDI input line is selected with the [INPUT] button on

the front panel:

Embedded audio (SDI terminal)

When input lines other than SDI1 or SDI2 are selected with

the [INPUT] button on the front panel:

Analog (AUDIO input terminal)

<ANALOG> Analog (AUDIO input terminal)

EMBEDDED

SELECT L

CH1 - CH8

(Factory

Selects embedded audio channel output to the left (L) headphone.

default: CH1)

EMBEDDED

SELECT R

CH1 - CH8

(Factory

Selects embedded audio channel output to the right (R) headphone.

default: CH2)

LEVEL

METER ^*1

OFF

Selects/turns off the audio level meter displayed by OSD.

Selects the number of audio level meter channels.

CH SELECT

8CH

4CH

2CH

0dB POINT

CH INFO.

OFF

Selects and turns off 0 dB line on/off displayed on the audio level meter.

Selects and turns off displays on the audio level meter.

OFF

*1 When ANALOG is selected in the “INPUT SELECT” menu, the LEVEL METER does not indicate the audio level

meter even when set to ON.

Main Menu (continued)

DISPLAY SETUP

Underlined values indicate factory defaults.

Sub menu

TWO

WINDOW

Settings

Description

L/S

M/M

S/L

Selects size of split-screen displays.

<L/S> main window LARGE, sub-window SMALL

<M/M> main window MEDIUM, sub-window MEDIUM

<S/L> main window SMALL, sub-window LARGE

2D ONLY

SIZE

SUB INPUT

VIDEO

SDI1

Selects sub-window input in split-screen display.

2D ONLY

SEL.

SDI2

YP^BPR/RGB

DVI-D

Turns the time code display on and off. ^*1

Selects position of time code display.

TIME CODE

POSITION

OFF

TOP

LEFT

CENTER

RIGHT

<TOP>

<LEFT>

Top center of screen

Bottom left of screen

<CENTER> Bottom center of screen

<RIGHT> Bottom right of screen

Selects font size of time code display.

<LARGE>

<SMALL>

FONT SIZE

LARGE

SMALL

Twice the height and width of menu font size

Menu font size

MODE

SELECT

Selects time code display mode. ^*1

LTC

VITC

LUB

VUB

<LTC>

<VITC>

<LUB>

<VUB>

Displays linear time code (LTC).

Displays vertical interval time code (VITC).

Displays user bits included in LTC.

Displays user bits included in VITC.

Turns closed caption display on and off. ^*2

CLOSED

OFF

CAPTION

2D ONLY

Selects the closed caption display mode. ^*2

MODE

CC4

CC3

CC2

CC1

SELECT

2D ONLY

*1 Available during HD-SDI input signals. Displays the signal input from SDI1 (L) when 3D mode is set to SIMUL.

*2 Available during VIDEO (NTSC) input. Closed captions appear as bright lines on line 21 when closed caption is

set to ON and underscan is also on.

Main Menu (continued)

2D ONLY

_TWO WINDOW function

The “TWO WINDOW” function displays two inputs selected from VIDEO, SDI1/2, YP^BPR/RGB or DVI-D in two

windows.

Each press of the button ([FUNCTION1] to [FUNCTION5]) (J page 35) to which the “TWO WINDOW” function

has been assigned changes the display mode.

Press the FUNCTION button to

which the TWO WINDOW

function has been assigned.

Main window (normal window)

• Main window: Displays input selected by “INPUT” in a single

window.

Video

Press the

button again

Main window

Sub-window

• Main window: Displays input selected by “INPUT.”

• Sub-window: Displays input selected in the “SUB INPUT SEL.”

submenu under the “DISPLAY SETUP” menu.

Change “GAMMA SELECT”, “COLOR SPACE”, “COLOR GAIN

R”, “COLOR GAIN B” submenu settings in the “VIDEO CONFIG”

menu to enable comparison with the main window (video).

Video

Press the

button again

Main window Sub-window

• Main window: Displays input selected by “INPUT” as a still life

image.

• Sub-window: Displays input selected in the “SUB INPUT SEL.”

submenu under the “DISPLAY SETUP” menu.

Change “GAMMA SELECT”, “COLOR SPACE”, “COLOR GAIN

R”, “COLOR GAIN B” submenu settings in the “VIDEO CONFIG”

menu to enable comparison with the main window (still image).

Still image

Video

Press the

button again

Sub-window

• Sub-window: Displays input selected in the “SUB INPUT SEL.”

submenu under the “DISPLAY SETUP” menu in a single window.

Video

Press the

button again

Note:

• When the main window and sub-window input setting is “YP^BPR/RGB” and “RGB-COMP,” the main window and

sub-window are displayed in a single window. When the input settings for the main window and sub-window are

both “DVI-COMP,” they are also displayed in a single window.

• When the input signals selected in the main and sub-window differ, the color shade, etc. may differ slightly.

• When the input signal terminals of video displayed in the main window and sub-window differ, the still image

function does not work.

• The main window is normally displayed on the left side.

• When SDI1 or SDI2 is selected for the main window and sub-window, both windows will show the same screen.

• When SDI2 and another input (except for a combination of SDI1 and SDI2) are used for the split screen display,

TIME CODE and audio level meter display will not function. In this case, use SDI1.

Main Menu (continued)

_TWO WINDOW size

The “TWO WINDOW SIZE” setting in the “DISPLAY SETUP” menu determines the size of the main window and

sub-window.

• Main window (SD) and sub-window (SD)

1920

1280

640

960

640

1280

“TWO WINDOW SIZE” setting: L/S

Display size: 4:3 or 5:4

“TWO WINDOW SIZE” setting: M/M

“TWO WINDOW SIZE” setting: S/L

• Main window (HD) and sub-window (HD)

1920

1280

640

960

640

1280

“TWO WINDOW SIZE” setting: L/S

Display size: 16:9 or 16:10

“TWO WINDOW SIZE” setting: M/M “TWO WINDOW SIZE” setting: S/L

Main Menu (continued)

• Main window (HD) and sub-window (SD)

1920

1280

640

960

640

1280

“TWO WINDOW SIZE” setting: L/S

Display size of main window: 16:9 or 16:10

Display size of sub-window: 4:3 or 5:4

“TWO WINDOW SIZE” setting: M/M

“TWO WINDOW SIZE” setting: S/L

• Main window (SD) and sub-window (HD)

1920

1280

640

960

640

1280

“TWO WINDOW SIZE” setting: L/S

Display size of main window: 4:3 or 5:4

Display size of sub-window: 16:9 or 16:10

“TWO WINDOW SIZE” setting: M/M

“TWO WINDOW SIZE” setting: S/L

• When the main window and sub-window display video from the same input line, TWO WINDOW SIZE is M/M.

Main Menu (continued)

_TWO WINDOW screen sync

In single screen display, the TWO WINDOW screen is synchronized to the frame rate frequency of the input signal

format.

In split screen display, the screen used as a reference for synchronization changes with the input signal format and

“TWO WINDOW SIZE” settings as shown in the following table.

Screen synchronization and display in split-screen mode

Sub-window

Input signal format 1035i

1080i

NTSC

PAL

480i/p

576i/p

No input

incompatible

format

TWO

WINDOW

SIZE

1080p

720p

Main window

1080/24PsF

Input signal format

DVI-COMP.

1035i

1080i

1080/24PsF

1080p

720p

Main window

sync

Main window sync

Split-screen display

Single screen

display

NTSC

PAL

L/S

M/M

S/L

480i/p

576i/p

DVI-COMP.

No input

incompatible format

Not displayed.

1035i

1080i

1080/24PsF

1080p

720p

Main window

sync

Single screen

display

Sub-window sync

Split-screen display

Main window

sync

Split-screen

display

NTSC

PAL

480i/p

576i/p

DVI-COMP.

No input

incompatible format

Sub-window sync

Single screen display

Not displayed.

1035i

1080i

1080/24PsF

1080p

720p

Sub-window sync

Split-screen display

NTSC

PAL

Not displayed.

480i/p

576i/p

DVI-COMP.

No input

incompatible format

Sub-window sync

Single screen display

• No screen is displayed when the screen is not synchronized to the reference sync or the reference sync is not

input or is in an incompatible format.

• When the frame frequency of the input signal formats of the main window and sub-window differ, frames may be

skipped in the screen that is not synchronized to the reference sync.

Main Menu (continued)

CONTROL

Underlined values indicate factory defaults.

Sub menu

Settings

Description

Selects operation. (with control clock)

<LOCAL> Enables front panel operation

CONTROL

LOCAL

REMOTE

<REMOTE> Enables remote operation

(front panel operation is locked) ^*1

LOCAL

ENABLE

DISABLE

INPUT

Selects the disabled operation on the front panel when selecting

“REMOTE” under “CONTROL”.

Only available when “REMOTE” is selected under “CONTROL”.

<DISABLE> Disables all front panel operations.

<INPUT>

Operation using button other than the [INPUT] button is

invalid.

*1 The menu can be displayed when the lock is engaged.

Only “CONTROL/LOCAL ENABLE” menu items are available when the lock is engaged.

The picture/volume adjusting menu does not accept changes when the lock is engaged.

The “LOCAL ENABLE” setting determines operations in lock mode.

The key mark is displayed in menu screen and status screen during lock engagement.

Menu Screen

Key mark

[MAIN MENU]

2D Status Screen

Key mark

3D Status Screen

Key mark

SIMUL

LINE BY LINE

SDI2(R): 1080/59.94i(R)

SDI1(L): 1080/59.94i(L)

HOURMETER

Sub menu

Settings

Description

OPERATION

XXXXXXh

Displays the number of hours it has been on.

300,000 hours or greater is displayed as “OVER”.

LCD

XXXXXXh

Displays the number of hours that the backlight has been on.

300,000 hours or greater is displayed as “OVER”.

Main Menu (continued)

_ Setting limitations in 2D mode ( : available, : can be set, but function is disabled, -: not available)

Input CH

SDI 1/2

YPB

RGB-VIDEO

DVI-VIDEO

VIDEO

RGB-COMP

DVI-COMP.

Setting item

SD HD SD

SYSTEM

3D INPUT TYPE

SIMUL MODE

H MIRROR

H SHIFT

MARKER

16:9

4:3

BACK

MARKER

CENTER

GPI PRESET1

GPI PRESET2

MARKER TYPE

CROSS HATCH

GAMMA SELECT ^*2

COLOR SPACE

COLOR TEMP.

SHARPNESS MODE ^*3

SHARPNESS H

SHARPNESS V

VIDEO

CONFIG

I-P MODE

MONO

ANAMO

SD ASPECT

SCAN

COLOR GAIN R

COLOR GAIN B

VIDEO

FORMAT

NTSC SETUP

SDI 1

SDI 2

INPUT

YPBPR/RGB

MODE

SELECT

COMPONENT LEVEL

SELECT SYNC

COMP.

DVI-D

MODE

*1 This function is not available in the split-screen display of the “TWO WINDOW” function.

*2 Settings are reflected to the sub-window in the split-screen display of the “TWO WINDOW” function.

*3 Settings are reflected to the main window and the sub-window in the split-screen display of the “TWO

WINDOW” function.

Main Menu (continued)

Input CH

SDI 1/2

YPB

RGB-VIDEO

SD HD

DVI-VIDEO

SD HD

VIDEO

RGB-COMP

DVI-COMP.

Setting item

AUDIO

SD HD SD

INPUT SELECT

EMBEDED SELECT L

EMBEDED SELECT R

LEVEL METER

CH SELECT

0dB POINT

CH INFO.

TWO WINDOW

SIZE

SUB INPUT SEL.

TIME CODE

POSITION

DISPLAY

SETUP

FONT SIZE

MODE SELECT

CLOSED

CAPTION

MODE SELECT

PHASE

CHROMA

Picture

BRIGHT

adjustment

CONTRAST

BACKLIGHT

Main Menu (continued)

_ Setting limitations in 3D mode ( : available, : can be set, but function is disabled, -: not available)

Input CH

SDI 1/2

DVI-VIDEO

DVI-COMP.

Setting item

SYSTEM

3D INPUT TYPE

SIMUL MODE

H MIRROR

H SHIFT

MARKER

16:9

4:3

BACK

MARKER

CENTER

GPI PRESET1

GPI PRESET2

MARKER TYPE

CROSS HATCH

GAMMA SELECT

COLOR SPACE

COLOR TEMP.

SHARPNESS

MODE

SHARPNESS H

SHARPNESS V

VIDEO

CONFIG I-P MODE

MONO

ANAMO

SD ASPECT

SCAN

COLOR GAIN R

COLOR GAIN B

VIDEO

FORMAT

NTSC SETUP

SDI 1

SDI 2

YP^BPR/RGB

MODE

INPUT

SELECT

COMPONENT LEVEL

SELECT SYNC

COMP.

DVI-D

MODE

INPUT SELECT

EMBEDED SELECT L

EMBEDED SELECT R

LEVEL METER

CH SELECT

0dB POINT

CH INFO.

AUDIO

*1 This function can only be set when SIMUL is selected for the “3D INPUT TYPE” option.

Main Menu (continued)

Input CH

SDI 1/2

DVI-VIDEO

DVI-COMP.

Setting item

TWO WINDOW

SIZE

SUB INPUT SEL.

TIME CODE

POSITION

DISPLAY

SETUP

FONT SIZE

MODE SELECT

CLOSED

CAPTION

MODE SELECT

PHASE

CHROMA

Picture

adjustment

BRIGHT

CONTRAST

BACKLIGHT

REMOTE Specifications

This monitor permits remote operation via GPI/RS-232C terminal.

GPI terminal

GPI screen items correspond to the following terminals. Use the GPI menu to assign functions to each terminal (

page 39).

Functions assigned to terminals are executed when GND (pin 5) is short-circuited (ON) or open (OFF).

Pin number

Signal

GPI1

GPI2

GPI3

GPI4

GND

GPI5

GPI6

GPI7

GPI8

_Operating conditions

Level operation: Operates when GND is short-

circuited.

Edge operation: Operates when GND changes from

open to short-circuited.

• When level operation is assigned to more than one

terminal, the function operates as long as one of

the terminals is short-circuited.

Edge operation should hold for 0.2 s or more after a

change.

GPI Terminal (9P)

Assigned item

Function

Undefined (no function assigned)

Operating conditions

UNDEF

—

MARKER1

ON/OFF

Switches marker display defined in “GPI PRESET1”

(J page 26) in the “MARKER” menu.

Level operation

(Short-circuited: ON, Open: OFF)

MARKER2

ON/OFF

Switches marker display defined in “GPI PRESET2”

(J page 26) in the “MARKER” menu.

Level operation

(Short-circuited: ON, Open: OFF)

MARKER

BACK HALF

Reduces the brightness of the background outside the

Level operation

(Short-circuited: ON, Open: OFF)

marker displayed in “GPI PRESET1” (

page 26) to 50%.

MARKER

BACK BLACK

Reduces the brightness of the background outside the

marker displayed in “GPI PRESET1” ( page 26) to 0%.

Level operation

(Short-circuited: ON, Open: OFF)

CENTER MARKER

Turns the center marker display on and off. (When

other markers are displayed, this marker is

superimposed on other markers.)

Level operation

(Short-circuited: ON, Open: OFF)

Switches the input line of the main window to VIDEO.

Edge/level operation

INPUT SEL. VIDEO

2D ONLY

INPUT SEL. SDI1

INPUT SEL. SDI2

INPUT SEL.

Switches the input line of the main window to SDI1.

Switches the input line of the main window to SDI2.

Edge/level operation

Switches the input line of the main window to YPBPR/

RGB.

2D ONLY

YP^BPR/RGB

INPUT SEL. DVI-D

Switches the input line of the main window to DVI-D.

Edge/level operation

Sets the aspect ratio for SD signal input in the main

window or sub-window single screen display.

Level operation

(Short-circuited: 16:9, open: 4:3)

2D ONLY

SD ASPECT

Switches between “UNDER” and “NORMAL” scan

modes in the main window or sub-window single

screen display.

Level operation (Short-circuited: UNDER,

Open: NORMAL)

2D ONLY

SCAN

Lights the red tally.

Level operation

(Short-circuited: ON, Open: OFF)

R-TALLY

Lights the green tally.

Level operation

G-TALLY

MONO

(Short-circuited: ON, Open: OFF)

Switches between color and monochrome (MONO).

(Disabled during PC signal input)

Level operation (Short-circuited:

monochrome, Open: color)

GAMMA SEL. FILM

Switches the gamma curve in the main window to

FILM mode.

Level operation (Short-circuited: FILM

mode, Open: STANDARD mode)

GAMMA SEL. STDIO/

PST

Switches the gamma curve in the main window to

STDIO/PST mode.

Level operation (Short-circuited: STDIO/

PST mode, Open: STANDARD mode)

Selects the SYNC when using YPBPR and RGB-

VIDEO input.

Level operation

(Short-circuited: EXT, Open: INT)

SELECT SYNC

2D ONLY

*1 When a 16:9 marker and a 4:3 marker are simultaneously selected and activated on a 16:9 aspect ratio display,

both markers are displayed.

*2 When a 16:9 marker and a 4:3 marker are simultaneously displayed, the background of the marker selected by

the 16:9 marker is controlled.

*3 When “R-TALLY” and “G-TALLY” simultaneously go on, the tally color changes to orange.

REMOTE Specifications (continued)

_Priority of assigned functions

• When both “MARKER1” and “MARKER2” are activated at the same time, “MARKER1” has priority. However,

when the display aspect ratio is 4:3, the “MARKER1” aspect ratio is 16:9 and the “MARKER2” aspect ratio is 4:3,

“MARKER2” is displayed. In this case, the “MARKER2” background is controlled.

• When “MARKER BACK HALF” and “MARKER BACK BLACK” are activated at the same time, “MARKER BACK

BLACK” has priority.

• During GPI edge operation and two or more of “INPUT SEL. VIDEO”, “INPUT SEL. SDI1”, “INPUT SEL. SDI2”,

“INPUT SEL. YP^BPR/RGB” and “INPUT SEL. DVI-D” are simultaneously activated, priority goes to the last

activated item. During level operation, priority is assigned in the following order: “INPUT SEL. VIDEO”, “INPUT

SEL. SDI1”, “INPUT SEL. SDI2”, “INPUT SEL. YP^BPR/RGB” and “INPUT SEL. DVI-D”.

• When “GAMMA SEL. FILM” and “GAMMA SEL. STDIO/PST” are activated at the same time, “GAMMA SEL.

FILM” has priority.

RS-232C terminal

The following diagram and the table on the lower right show RS-232C terminal pin arrangement and connections.

For details on systems using RS-232C, be sure to consult your dealer.

PC Side

Pin number

(Straight)

BT-3DL2550P/E Side

Signal

N.C.

RXD

TXD

DTR

GND

DSR

RTS

CTS

N.C.

Pin number

Signal

N.C.

TXD

RXD

DSR

GND

DTR

CTS

RTS

N.C.

RS-232C terminals (9P)

RS-232C remote control method

_Connectors and signals

Connector: D-SUB 9-pin (female)

Signal

_Command format

STX (02h) Command

Data

ETX (03h)

• The command is the 3-character string starting with

STX and ending with ETX.

• Append any data after the colon (:) following the

command, as required.

Pin number Signal

Description

N.C. Not connected

TXD Transmission data

RXD Reception data

DSR Connected inside

GND Ground

DTR Connected inside

CTS Connected inside

RTS Connected inside

N.C. Not connected

_Response formats

1. Setting command response

STX (02h)

Command

ETX (03h)

2. Query command response

STX (02h)

Data

3. Error response

STX (02h)

Error code

_Communication parameters

Error codes

ER001: Invalid command

ER002: Parameter error

Signal level

Synchro system

Transfer rate

Parity

RS-232C compliant

Asynchronous

9600 bps

None

Data length

Stop bit

8 bit

1 bit

Flow control

None

REMOTE Specifications (continued)

_Setting command

No Command

Description

Input switch

Data

1: SDI2

Response

IIS ^*1

0: SDI1

3: YPBPR/RGB

2: VIDEO

6: DVI-D

IIS

2D ONLY

VPC ^*2

Image quality

adjustment

CON00-60 : Contrast settings

BRI00-60 : Brightness settings

CRO00-60 : Chroma settings

PHA00-60 : Phase settings

VPC

OBO ^*2

Blue only

HV Delay

0: OFF

1: ON

OBO

OHV

OHV ^*1

0: OFF

3: HV DELAY

1: H DELAY

2: V DELAY

2D ONLY

VBL^*2

Backlight

00-60: Backlight setting

VBL

DCH

DSD

ISM

DCH ^*2

Cross hatch

Status display

Analog mode

0: OFF

1: LOW

1: 3SEC OFF

2: HIGH

2: OFF

DSD ^*2

0: CONTINUE

ISM ^*2

2D ONLY

ANA0: YPBPR

ANA1: RGB-VIDEO

ANA2: RGB-COMP.

0: INT

IRF ^*2

2D ONLY

SELECT Sync

1: EXT

IRF

ISM ^*2

DVI-D mode

DVI0: DVI-VIDEO

DVI1: DVI-COMP.

ISM

DMK ^*3

Marker settings

16:9 marker

MK100: OFF

MK102: 88%

MK104: 95%

MK106: 13:9

MK108: 90%

MK110: VISTA

DMK

MK101: 80%

MK103: 93%

MK105: 14:9

MK107: 4:3

MK109: CNSCO

MK1xxx: USER (range: 080 - 100%)

4:3 marker

MK200: OFF

MK202: 88%

MK204: 95%

MK201: 80%

MK203: 93%

MK208: 90%

MK2xxx: USER (range: 080 - 100%)

Marker background

BAK0: NORMAL BAK1: HALF

Center marker

BAK2: BLACK

3: STDIO/PST

CMK0: OFF

CMK1: ON

MGM ^*1

Gamma selection

1: STANDARD

2: FILM

MGM

MCT

MCT ^*2

Color temperature

settings

00: D56

03: VAR1

10-73: USER0 - 63

01: D65

04: VAR2

02: D93

05: VAR3

VPC ^*2

Sharpness settings

IP mode settings

SHP0: LOW

SHH00-30: Horizontal sharpness settings

SHV00-30: Vertical sharpness settings

SHP1: HIGH

VPC

MIP

2D ONLY

MIP ^*1

0: MODE1 1: MODE2

2D ONLY

*1 This command is enabled in single screen display in “TWO WINDOW” mode and in the main window in split-

screen display.

*2 This command is enabled in single screen display in “TWO WINDOW” mode and in the main window and sub-

window in split-screen display.

*3 This command is enabled in the sub-window in single screen display in “TWO WINDOW” mode.

REMOTE Specifications (continued)

No Command

Description

Data

2: ON

1: 4:3

Response

OMO

OMO ^*2

Monochrome settings

SD aspect settings

1: OFF

0: 16:9

MAS ^*3

MAS

2D ONLY

MSC ^*3

Scan settings

0: NORMAL

1: UNDER

MSC

2D ONLY

MCO ^*2

Remote settings

0: LOCAL

1: REMOTE

1: INPUT

MCO

MLE

MLE ^*2

Remote operation

settings

0: DISABLE

DIT

3D input type settings

0: SIMUL

2: SIDE BY SIDE

1: LINE BY LINE

DIT

DSM

SIMUL settings

0: LINE BY LINE

2: SDI1 (L)

1: OVERLAY

3: SDI2 (R)

DSM

4: COMPARISON

DHM

Mirror settings

0: OFF

1: ON

DHM

*2 This command is enabled in single screen display in “TWO WINDOW” mode and in the main window and sub-

window in split-screen display.

*3 This command is enabled in the sub-window in single screen display in “TWO WINDOW” mode.

_Query command

This command returns the main window setting.

No Command

Description

Data

Response

1: SDI2

QIS

Input selection

0: SDI1

2D ONLY

3: RGB-VIDEO

2D ONLY

6: RGB-COMP.

10: DVI-COMP.

2: YP^BPR

4: VIDEO

9: DVI-VIDEO

00-60

QPC

Image quality

adjustment

CON : Contrast setting value

BRI

Brightness setting value

00-60

CRO : Chroma setting value

PHA : Phase setting value

00-60

QBO

QBL

QCH

QMK

Blue only

Backlight

Cross hatch

Marker

0: OFF

00-60

1: ON

0: OFF

1: LOW

2: HIGH

MAK : Area marker

00: OFF

01: 80%

04: 95%

07: 4:3

02: 88%

05: 14:9

08: 90%

03: 93%

06: 13:9

09: CNSCO

10: VISTA

80-100: USER80 - 100

BAK : Background

0: NORMAL

0: OFF

1: HALF

1: ON

2: BLACK

CMK : Center marker

QGM

QCT

Gamma

1: STANDARD 2: FILM 3: STDIO/PST

Color

temperature

00: D56

01: D65

04: VAR2

02: D93

05: VAR3

03: VAR1

10-73: USER0 - 63

QPC

Sharpness

SHP : Sharpness mode

0: LOW

00-30

1: HIGH

SHH : Horizontal sharpness value

SHV : Vertical sharpness value

00-30

2D ONLY

IP mode

0: MODE1

1: OFF

1: MODE2

2: ON

QIP

2D ONLY

QMO

Monochrome

*1 When in SIMUL mode, only “0:SDI1” responds.

*2 Returns the 16:9 marker status when both 16:9 and 4:3 markers are displayed.

REMOTE Specifications (continued)

No Command

Description

Data

Response

1: 4:3

QAS

Aspect

0: 16:9

2D ONLY

QSC

Scan

0: NORMAL

0: YPBPR

0: INT

1: UNDER

1: RGB-VIDEO 2: RGB-COMP.

2D ONLY

QAN

Analog mode

SELECT sync

2D ONLY

QSY

1: EXT

2D ONLY

QDV

QFR

DVI-D mode

Format

0: DVI-VIDEO

1: DVI-COMP.

00: NO SIGNAL

01: 1080/60i

03: 1080/50i

05: 1080/29p

07: 1080/24p

02: 1080/59i

04: 1080/30p

06: 1080/25p

08: 1080/23p

2D ONLY

09: 1080/24PsF

13: 720/60p

10: 1080/23PsF

14: 720/59p

2D ONLY

15: 576/50i

17: 480/60i

16: 480/60p

18: 576/50p

21: 1080/59p

23: 720/50p

2D ONLY

20: 1080/60p

22: 1080/50p

2D ONLY

50: 640 × 400 (70 Hz)

51: 640 × 480 (60 Hz)

52: 640 × 480 (75 Hz)

53: 640 × 480 (85 Hz)

54: 800 × 600 (60 Hz)

55: 800 × 600 (75 Hz)

56: 800 × 600 (85 Hz)

57: 1024 × 768 (60 Hz)

58: 1024 × 768 (70 Hz)

59: 1024 × 768 (75 Hz)

60: 1024 × 768 (85 Hz)

61: 1280 × 768 (60 Hz)

62: 1280 × 768 (75 Hz)

63: 1280 × 1024 (60 Hz)

2D ONLY

64: 800 × 600 (70 Hz)

65: 1280 × 768 (50 Hz)

66: 1600 × 1200(60 Hz)

67: 1920 × 1200(60 Hz)

2D ONLY

FF: UNSUPPORT SIGNAL

QID

QIT

Model

BT-3DL2550

3D input type

settings

0: SIMUL

2: SIDE BY SIDE

1: LINE BY LINE

QSM

QHM

SIMUL

settings

0: LINE BY LINE

2: SDI1 (L)

4: COMPARISON

1: OVERLAY

3: SDI2 (R)

Mirror settings

0: OFF

1: ON

Maintenance inspections

Maintenance inspections through periodic and appropriate maintenance are essential to keep the monitor in

optimum condition and ensure safe operation. Be sure to conduct the following maintenance inspections to enable

long-term, full use of all its functions.

Necessity of periodic maintenance service

The backlight in the LCD panel is a consumable component that deteriorates over time leading to gradual loss of

performance that could eventually result in a malfunction.

Conventional after-sales service that replaces parts when they break down should therefore be combined with a

regularly conducted comprehensive service to maintain normal operation and prevent unforeseen breakdown of

consumables.

Care and cleaning of the monitor

• Clean the cabinet and protection panel by gently wiping it with a soft cloth.

To remove stubborn soiling, use a cloth dampened in a weak neutral detergent solution and thoroughly wrung out.

Then wipe with a dry cloth. Any moisture entering the monitor could damage it.

• Do not use benzene, thinner and similar solvents for cleaning.

They could discolor the surface and cause the paint to peel.

• Do not directly expose the monitor to spray cleaning.

Any moisture entering the monitor could damage it.

Care and storage of 3D Polarized Eyewear

• Use a soft dry cloth intended for use on eye-glasses when cleaning this product. Remove lint from the cloth before

use as it may damage the product. Do not use benzene, thinner or similar solvents for cleaning as they could

discolor the surface and cause the paint to peel.

• Do not apply water or other liquids to the 3D Polarized Eyewear when cleaning.

• Avoid storing 3D Polarized Eyewear in places with a high temperature or high humidity.

• Contact your dealer if additional 3D Polarized Eyewear is required.

Error Display

When an error has occurred for some reason, the tally lamp notifies the error.

Error display

Inverter error

The tally lamp

flashes red at

1-second intervals.

Symptom

Remedy

If a malfunction occurs in the inverter that

controls backlight brightness, the

backlight goes off and the screen turns

black.

Turn off the power and then turn it back

on. If the problem still persists, consult

your dealer.

Before calling for support

When a fault is suspected (Troubleshooting)

If unresolved issues remain after referring to the points below, please consult the store from which the product was

purchased.

Symptom

Image is not 3D

Remedy

• Is the monitor switched to 3D image mode?

Even in 3D mode, there is a non-stereoscopic mode.

• Persons with a large difference in visual acuity between their left and

right eyes may have difficulty seeing 3D images, or may not be able to

see them at all. Use this monitor after taking the appropriate vision

correction measures.

The 3D video looks strange

• Is the 3D image horizontally inverted?

Ensure that the left eye image signal and the right eye image signal are

input correctly when in SIMUL mode.

Specifications

_General

YP^BPR/RGB output terminals

BNC × 3

Supply Voltage 24 V DC, 4.5 A

5 V DC, 0.03 A

Through-out (Automatic

75 Ω termination)

SYNC/HD output terminals

indicates safety information.

Dimensions (W × H × D):

BNC × 1

Through-out (Automatic

1 kΩ termination)

BNC × 1

599 mm × 440 mm × 220 mm

VD output terminals

(23-5/8 inches × 17-5/16 inches ×

8-11/16 inches) (Including stand)

599 mm × 410 mm × 100 mm

(23-5/8 inches × 16-1/8 inches ×

3-15/16 inches) (Not including stand)

approx. 10.3 kg (22.7 lb)

Through-out (Automatic

1 kΩ termination)

Headphone output terminals

Stereo mini-jack M3 × 1

32 Ω, adjustable level

Mass:

(Including stand)

approx. 8.8 kg (19.4 lb)

(Not including stand)

REMOTE:

GPI

D-SUB 9-pin × 1

RS-232C

Ambient temperature:

5 °C to 35 °C (41 °F to 95 °F)

Operating humidity:

20% to 80% (no condensation)

Storage temperature:

-20 °C to 60 °C (-4 °F to 140 °F)

_AC adapter

Supply Source 100 V - 240 V, 50/60 Hz

1.6 A - 0.6 A

Power Output 24 V DC, 4.5 A

5 V DC, 0.03 A

_Display panel

Size:

25.5 type

16:10

indicates safety information.

Aspect ratio:

Number of pixels: 1920 × 1200 (WUXGA)

Dimensions (W × H × D):

232 mm × 50.5 mm × 177 mm

(9-1/8 inches × 2 inches × 6-15/16

inches)

Display colors:

View angle:

approx. 16.77 million colors

178° both vertically and horizontally

Xpol^®polarizing panel

Panel surface:

Mass:

approx. 1.7 kg (3.5 lb)

_Connectors

Input

VIDEO input terminal BNC × 1

SDI input terminal BNC × 2

Compliant with SMPTE 274M, 296M, 259M-C

and ITU-R BT.656-4

EMBEDDED AUDIO

YPBPR/RGB input terminal BNC × 3

SYNC/HD input terminal BNC × 1

SYNC signal level 0.3 V [p-p] - 4.0 V [p-p]

HD signal level

VD input terminal

VD signal level

TTL level

BNC × 1

TTL level

DVI-D × 1

DVI-D input terminal

HDCP compatible, TMDS single link

Vertical frequency 50.0 Hz - 60.0 Hz

Horizontal frequency 31.5 kHz - 67.5 kHz

Dot clock

25 MHz - 165 MHz

AUDIO input terminals Pin jack × 2 (stereo)

Signal level

0.5 Vrms

DC IN terminals

XLR 4 pins × 1

Output:

VIDEO output terminals BNC × 1

Through-out (Automatic

75 Ω termination)

BNC × 2

SDI output terminals

Active through output

Inrush current, measured according to European

standard EN55103-1: 10.0 A

Specifications (continued)

_ Signal formats supported in 2D mode ( : Compatible, : Limited compatibility, -: Not compatible)

Input signal formats VIDEO

SDI1

SDI2

YP^BPR

RGB-VIDEO RGB-COMP. DVI-VIDEO DVI-COMP.

NTSC

PAL

480/59.94i

480/59.94p

576/50i

576/50p

720/50p

720/59.94p

720/60p

1035/59.94i

1035/60i

1080/23.98PsF

1080/24PsF

1080/23.98p

1080/24p

1080/25p

1080/29.97p

1080/30p

1080/50i

1080/50p

1080/59.94i

1080/60i

1080/59.94p

1080/60p

640 × 400 (70 Hz)

640 × 480 (60 Hz)

640 × 480 (75 Hz)

640 × 480 (85 Hz)

800 × 600 (60 Hz)

800 × 600 (70 Hz)

800 × 600 (75 Hz)

800 × 600 (85 Hz)

1024 × 768 (60 Hz)

1024 × 768 (70 Hz)

1024 × 768 (75 Hz)

1024 × 768 (85 Hz)

1280 × 768 (50 Hz)

1280 × 768 (60 Hz)

1280 × 768 (75 Hz)

1280 × 1024 (60 Hz)

1600 × 1200 (60 Hz)

1920 × 1200 (60 Hz)

*1 When 1035/59.94i signal is input, displayed as 1080/59.94i. Other various marker displays will use the 1080/

59.94i marker.

*2 When 1035/60i signal is input, displayed as 1080/60i. Other various marker displays will use the 1080/60i

marker.

*3 Only compatible with VESA (Video Electronics Standards Association) Reduced Blanking (Clock: 154 MHz,

Hsync: positive logic, Vsync: negative logic).

Specifications (continued)

_ Signal formats supported in 3D mode ( : Compatible, : Limited compatibility,

: Not compatible)

SIDE BY SIDE

SIMUL

LINE BY LINE

Input signal formats

SDI

DVI-VIDEO DVI-COMP

SDI

DVI-VIDEO

720/50p

720/59.94p

720/60p

1035/59.94i

1035/60i

1080/23.98PsF

1080/24PsF

1080/25PsF

1080/29.97PsF

1080/30PsF

1080/50i

1080/59.94i

1080/60i

1920 × 1200 (60 Hz)

*1 When 1035/59.94i signal is input, displayed as 1080/59.94i. Other various marker displays will use the 1080/59.94i marker.

At this time the top of the screen will flicker. This is not a fault.

*2 When 1035/60i signal is input, displayed as 1080/60i. Other various marker displays will use the 1080/60i marker. At

this time the top of the screen will flicker. This is not a fault.

*3 Displayed dot by dot in 3D mode (except COMPARISON) without altering the input signal size.

*4 Only supported with LINE BY LINE format.

*5 Displayed as 1080/50i when input is 1080/25PsF.

*6 Displayed as 1080/59.94i when input is 1080/29.97PsF.

*7 Displayed as 1080/60i when input is 1080/30PsF.

Weight and dimensions when shown are approximately.

Specifications are subject to change without notice.

MEMO

Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households)

This symbol on the products and/or accompanying documents means that used electrical and electronic products

should not be mixed with general household waste.

For proper treatment, recovery and recycling, please take these products to designated collection points, where they will

be accepted on a free of charge basis. Alternatively, in some countries you may be able to return your products to your

local retailer upon the purchase of an equivalent new product.

Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on

human health and the environment which could otherwise arise from inappropriate waste handling. Please contact your

local authority for further details of your nearest designated collection point.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

Information on Disposal in other Countries outside the European Union

This symbol is only valid in the European Union.

If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.

Panasonic Corporation

Web Site: http://panasonic.net

Panasonic Solutions Company

3 Panasonic Way, Secaucus, NJ 07094 Tel: 877-803-8492

www.panasonic.com/broadcast e-mail: [email protected]

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga, Ontario L4W 2T3 Tel: 905-624-5010

Panasonic de México S.A. De C.V.

Casa Matriz: Moras No.313 Col. Tlacoquemecatl Del Valle Del.Benito Juárez México, D.F., C.P.03200

Tel: 55-5488-1000 Fax: 55-5575-6783

Panasonic Latin America, S.A.

P.O.Box 0816-03164 Panama, Republic of Panama Tel: +507-229-2955 Fax: 507-229-5352

Panasonic do Brasil Ltda.

Rua Cubatão, 320-6^oandar-Paraíso CEP 04013-001- São Paulo -SP Tel: 11-3889-4000 Fax: 11-3889-4004

P E

Inova High Performance CPU board ICP PII User Manual
Intel BX80623I72600K User Manual
KitchenAid KGCV566M User Manual
Lenovo THINKCENTRE 9644 User Manual
LG Electronics 47WV30 BAAM User Manual
NEC MultiSync LCD2080UXI User Manual
Philips 25PT7308 User Manual
Philips 29PT5642 User Manual
Philips 190CW User Manual
Philips 235BL2 User Manual