Palsonic 7128G User Manual

OWNER'S MANUAL  
71CM CORDLESS REMOTE COLOUR TELEVISION  
MODEL: 7128G  
Type Tested  
Electrical  
Safety  
AS/NZS 3250 Lic 4166  
Standards Australia  
APP No: N15899  
PALSONIC CORPORATION PTY LTD  
1 JOYNTON AVENUE  
WATERLOO NSW 2017 AUSTRALIA  
TEL:(02)9313 7111  
FAX:(02)9313 7555  
PALSONIC CUSTOMER SERVICE  
TELEPHONE  
AUSTRALIA:1300 657 888  
INTRODUCTION  
Features  
.
Hyperband  
.
English/Chinese on-screen menu display  
.
256 preset channels  
Intellectualized I2 C-bus control  
.
.
Full function remote control  
.
ON Timer, OFF Timer  
.
Four picture modes' setting  
.
AUDIO/VIDEO input & output terminals  
.
S-VIDEO Terminal  
.
Program scan function  
.
Games calendar function  
.
Advanced digital picture improvement circuit  
.
Digital AFT technology  
.
Channel reservation  
1
NOTES FOR OPERATION  
Do not let the TV set be in stand-by condition for a long period of time. When it is not in use, please  
turn off the power supply and remove the power plug. When it is to be left unattended for  
a prolonged period of time, it is recommended to disconnect the connection to the outdoor aerial, to  
avoid thunder strike.  
*
* Please follow cautions for safety in the TV set instructions, and all warnings and descriptions denoted  
on the TV set.  
Cautions for safety  
Note: This TV set can be operated on an AC power of 240V, 50Hz. You should not use power  
supply of the other type.  
In order to wipe dust off the  
picture tube or off the cabinet,  
you should remove the power  
plug from the wall outlet first.  
You can wipe lightly with a  
piece of dry, clean, soft cloth.  
When an unusual situation  
occurs, turn off the power  
switch at once and remove the  
plug from the wall outlet.  
Contact a qualified service  
department in your local area.  
Do not expose the TV set to  
rain or excessive moisture, to  
prevent tire disaster or  
electric shock. Avoid using  
the set in very warm or damp  
places. Never use it in a  
bathroom.  
The TV set should be placed  
on an adequate place without  
exposing it to direct sunlight  
and other sources of heat to  
prevent the deformation of the  
cabinet or damage to components.  
Do not cover the Ventilating  
holes in the cabinet. Keep a  
space of more than 5cm from  
the walls to the TV set, to  
There exists High Voltage in  
this TV set. Do not remove  
the cover to avoid danger.  
guarantee the good ventilation.  
When the power cord or the  
plug is damaged, please  
contact a qualified service  
department to get service.  
When the TV set is to be left  
unattended, please turn off the  
power switch and remove the  
plug from the wall outlet.  
2
Installation  
Antenna Connection  
To ensure a bright-coloured and clear picture, you should use an outdoor aerial or CATV cable. If  
the signals are strong enough, you may use an indoor aerial.  
Note: In case of using the  
Twin-lead aerial feeder (300 )  
for UHF/VHF aerial, use a 300-75  
ohm adaptor (not supplied)  
When using the coaxial cable (not  
supplied) (75 ) for UHF/VHF  
aerial, connect the plug into the  
75 ohm aerial socket directly.  
Note:  
When you connect the outdoor aerial cable to the aerial terminal on the TV set, please turn off the  
power switch on the TV while connecting the antenna lead.  
In thunder and lightning weather, please disconnect the outdoor aerial to avoid thunder/lightning  
strike.  
Effective range of the remote  
control operation  
Battery installation  
(1) Remove the back battery cover.  
(2) Insert two size AAA batteries according to  
the polarity indication inside the remote  
controller.  
Notes:  
1.  
When the remote controller is not used for  
an extended period of time or the batteries  
are worn out, please remove the batteries in  
time to avoid battery leakage.  
Avoid moisture and mechanical shock to  
the remote controller.  
2.  
3.  
Do not drop, dampen or disassemble the  
remote controller.  
3
Appearance  
Front view  
Note: Functions of MENU, TV/AV, VOLUME+/-, CH  
remote controller.  
are also provided to the  
Back View  
4
Appearance  
Remote Controller  
5
Menu Introduction  
Introducing the menu  
You can use the on-screen menus to set the picture quality and other settings. You can use buttons on  
both the remote controller and the TV to operate the menus.  
Notes:  
To select each item, use the or  
button.  
Normal Screen  
To adjust or set each item, use the  
or  
button  
Press MENU button  
76  
75  
100  
50  
COLOR  
BRIGHT  
CONT  
SHARP  
SELECT:  
SET:  
Press MENU button  
008  
VHFL  
OFF  
POSITION  
BAND  
SKIP  
SEARCH  
MFT  
AUTO MEMORY  
Press MENU button  
ENG/  
AUTO  
BG  
LANGUAGE  
C.SYSTEM  
S.SYSTEM  
B.B SET  
ON  
SELECT:  
SET:  
Press MENU button  
CALENDAR  
GAME 1  
GAME 2  
SELECT:  
SET:  
Press MENU button  
18.3018  
OFF  
OFF  
-
NOW TIME  
ON TIME  
OFF TIME  
ON CHANNEL  
TIME ADJ  
0M  
SELECT:  
SET:  
Press MENU button  
OFF  
-
TIME  
CHANNEL  
SELECT:  
SET:  
Press MENU button  
6
OPERATION  
Turning the Power On/Off  
.
The following describes how to turn the TV on/off using the TV's main switch and the remote  
controller.  
To turn the power on/off  
1. Press the POWER switch, the red power indicator lights up.  
2.  
Press the  
button or any one of 0~9 number buttons on the remote controller to  
turn the set on and the green indicator lights up.  
Without using the remote controller, you can directly press VOL  
or TV/AV button on the set to turn on the TV.  
or CH  
*Note:  
If there are no input signals to the TV when the TV set is on, a blue background will  
appear on the screen (when B.B (blue back) is set ON.)  
After 15 minutes if there are still no signals to the TV, it will enter into standby mode  
automatically  
3. Press the POWER switch to turn off the set completely.  
If you want to turn off the TV temporarily, press the  
switch the set to standby mode.  
button on the remote controller to  
4.  
Note:  
To prolong the picture tube's life, us a delayed shut-down circuit is adopted. The  
functions only when the set is turned on for more than 5 seconds.  
button  
Special indication:  
Auto-Power-Off function: there are two kinds of Auto-Power-Off function:  
If a vacant channel is tuned or TV broadcast for a day is finished, and the blue background appears  
on the screen, the TV will automatically turn off after about 15 minutes.  
1.  
2. Sleep-timer function.  
3. OFF timer function  
7
OPERATION  
Tuning in  
There are two ways to preset channels: to preset channels automatically and to preset channels  
manually. Below we will describe how to preset the channels by making use of the menu.  
To preset channels (Auto search)  
Use the AUTO SEARCH function to preset all the active channels in your local area automatically.  
To enter into menu  
Press the MENU button repeatedly to select and  
highlight the  
appears on the screen automatically.  
icon, and the PRESET menu  
008  
VHFL  
OFF  
POSITION  
BAND  
SKIP  
SEARCH  
MFT  
AUTO MEMORY  
Press the or button to select the item upward or downward  
in the menu, press the  
item.  
or button to enter into the selected  
lllllllllllll  
Note: If this manual the MENU button refers to the MENU button on the remote controller or on the  
TV set, the or button refers to the or button on the remote controller or CH button  
on the TV set, the  
or  
button refers to the  
or  
button on the remote controller or the  
VOL+/- button on the TV set.  
AUTO SEARCH  
1.  
008  
VHFL  
OFF  
POSITION  
BAND  
Press the  
(PRESET) menu, press the or  
button to select AUTO MEMORY.  
SKIP  
SEARCH  
MFT  
AUTO MEMORY  
lllllllllllll  
2.  
Press the  
button to start the AUTO SEARCH. All  
active channels will be preset and stored into the  
memory automatically. After presetting, the TV will  
return to the first channel program.  
AUTO MEMORY 4 VHFL  
STOP  
3.  
During the process of AUTO SEARCH, pressing the  
button on the remote controller will stop the  
process the and TV will return to the first channel  
program.  
0
8
OPERATION  
Tuning in (continued)  
Use the MANUAL SEARCH function if desired channels can not be preset with the  
AUTO SEARCH or if you would like to preset channels to specific position numbers one by one.  
It is convenient to set the channel numbers to the same position numbers using MANUAL  
SEARCH and SKIP functions.  
To preset channels (Manual search)  
Manual search  
If AUTO SEARCH can not preset the desired channels, or you want to preset the desired channels one  
by one with the preferred channel numbers, please make use of Manual search.  
1.  
Press the MENU button repeatedly to enter into the  
(PRESET) menu, or press the or button to  
008  
VHFL  
OFF  
POSITION  
select POSITION. Press the  
or  
button  
BAND  
SKIP  
to select a desired position number (from  
0~255)  
SEARCH  
MFT  
AUTO MEMORY  
press the  
or  
within 0.7 seconds. Press and hold the  
for over 0.7 seconds to select a decimal number  
button to select a channel number  
Note:  
lllllllllllll  
or button  
2.  
Press the or button to select SEARCH. Press the  
button to search channels from current channel to  
higher channel (the screen displays glittering (" ").  
008  
VHFL  
OFF  
POSITION  
BAND  
SKIP  
Press the  
button to search channels from current channel  
SEARCH  
MFT  
AUTO MEMORY  
to lower channel (the screen displays glittering (" ").  
When a channel is located, the searching stops, this channel  
is then memorised with the preset position number.  
lllllllllllll  
you can also make use of BAND selection to quicken the  
Note:  
searching process in your desired band. Press the  
button moves the band to the next step in the sequence below.  
or  
008  
VHFL  
OFF  
POSITION  
BAND  
SKIP  
SEARCH  
MFT  
AUTO MEMORY  
lllllllllllll  
VHFL  
VHFH  
UHF  
3. When you want to store another channel at another position, repeat steps 1 & 2 above.  
9
OPERATION  
Tuning in (continued)  
To skip unnecessary position numbers and MFT (Manual Fine Tuning)  
To skip a position number  
After presetting the channel you can skip unnecessary position numbers so that only the channels you  
want to watch are selected.  
1.  
Enter into the  
(PRESET) menu, press the  
008  
VHFL  
OFF  
POSITION  
BAND  
or button to select POSITION , then select  
the unwanted program number with the  
button.  
SKIP  
or  
SEARCH  
MFT  
AUTO MEMORY  
lllllllllllll  
Press the or button to select "SKIP". Press the  
or button to select "SKIP ON".  
After completion of channel preset , the position  
number will then be skipped when you select  
2.  
008  
VHFL  
ON  
POSITION  
BAND  
SKIP  
SEARCH  
MFT  
AUTO MEMORY  
programs with the CH  
button.  
If you want to skip other unwanted programs, repeat step 1 above  
to change the program number.  
lllllllllllll  
To restore skip a position number  
Enter into the PRESET menu, Select the position number you want to restore. Press the or button to select  
"SKIP". Press the or button to select "SKIP OFF".  
MFT (Manual Fine Tuning)  
When picture and sound's effect of a channel is poor (for example: one or two CATV channel's picture  
and sound are not standard), you can correct them by making use of Manual Fine Tuning.  
1.  
Enter into  
(PRESET) menu, select the  
008  
VHFL  
OFF  
POSITION  
BAND  
program number you want to fine-tune.  
SKIP  
SEARCH  
MFT  
AUTO MEMORY  
lllllllllllll  
Press the or button to select MFT, then press  
2.  
the  
or  
button, the channel begins fine tuning  
until the optimum picture and sound is achieved.  
008  
VHFL  
OFF  
POSITION  
BAND  
SKIP  
SEARCH  
MFT  
AUTO MEMORY  
Note: if some channel’s colour or sound is abnormal, it may be that the  
setting of the colour is wrong, please do adjustment  
according to The setting of colour system (on page 11) to set the  
proper colour system.  
lllllllllllll  
3. To exit the menu, press the MENU button repeatedly or wait for 15 seconds.  
10  
OPERATION  
Tuning in (continued)  
The setting of colour system  
In factory the TV set's colour system has been preset to AUTO, if you want to change the  
system, please do the following adjustments.  
Note:  
1.  
[SYSTEM]  
Press the SYS button, the colour and sound  
AUTO  
BG  
COLOR  
SOUND  
system will be displayed on the screen.  
SELECT  
ADJUST  
If the colour is abnormal, press the or  
button to select COLOR, then press the  
button to select the proper colour system.  
Every time you press the or button,  
2.  
[SYSTEM]  
or  
AUTO  
BG  
COLOR  
SOUND  
the colour system will change in the sequence  
below.  
SELECT  
ADJUST  
358NTSC  
AUTO  
PAL  
443NTSC  
Now you can watch the broadcasting TV program on the preset channels.  
11  
OPERATION  
Channel selection  
You can watch TV programmes being broadcast on the preset channels.  
To watch a TV programme  
You can select your desired TV program by one of the following methods.  
Using the direct select buttons  
To select a one-digit position number (0~9)  
METHOD 1:Press the button and the screen displays "X- -", wait for 2  
seconds and the channel is selected.  
METHOD 2: Press 0 button and the screen displays "0- -", then press 0 button  
again, the screen displays "00-" then press the numbers. (The  
period of two-press must be within 2 seconds).  
After 2  
seconds  
X--  
X
To select a two-digit position number (10~99)  
METHOD 1:Press these two numbers and the screen displays "XX -", (The  
period of two-press must be within 2 seconds). Wait for 2  
seconds and the channel is selected.  
X--  
XX-  
XX  
METHOD 2:  
Press 0 button first, than press these two numbers, the screen  
displays "0XX", the channel is selected. (The period of  
two-press must be within 2 seconds).  
To select a three-digit position number (100~255)  
Press these three numbers and the screen displays "XXX" the channel  
is selected. (The period of two-press must be within 2 seconds).  
X--  
XX-  
XXX  
NOTE: If the input number is over 255, the screen will remain at the  
current viewed program.  
Using the CH  
buttons  
Press CH to select lower position numbers;  
CH to select higher ones.  
3
2
1
Using the PREVIOUS channel button (  
)
When there are no menus on the screen, pressing the  
button on the remote controller (below the MENU button)  
can swap the current viewed channel with the previous  
one. For example, the channel you previously watched is  
11  
2
11, the present channel is 2, press the  
button, it will  
return to channel 11, press the  
return to channel 2.  
button again it will  
Using the channel SCAN button  
Press SCAN button, the set will scan the channels from first channel to higher channels  
one by one, every program will be displayed for about 3 seconds and then go on scanning  
until all programs are scanned over and then return to your former viewed program.  
During the scanning, press SCAN button again, the set will return to your former viewed  
program.  
12  
OPERATION  
Convenient Picture Controls  
Selectable picture  
To select the picture mode  
You can select the picture quality instantly among three  
preset modes and one user-set mode.  
Press the P.S button to select the desired picture quality.  
BRILLIANT, NATURAL, MELLOW and PERSONAL  
BRILLIANT  
(user-set) can be selected cyclically.  
NATURAL  
MELLOW  
PERSONAL  
To set the desired picture quality to the PERSONAL position  
Press the MENU button to display the  
(PICTURE) menu. Or press the P.M button, to  
call up PICTURE menu.  
1.  
76  
75  
100  
50  
COLOR  
BRIGHT  
CONT  
SHARP  
Press the or button to select the desired  
2.  
SELECT  
ADJUST  
adjusting item, and press the  
button to adjust the level.  
or  
Pressing (PERSONAL)  
BRILLIANT NATURAL MELLOW  
Item  
COLOR  
paler  
deeper  
75  
75  
50  
50  
90  
40  
50  
50  
70  
30  
BRIGHTNESS  
darker  
weaker  
softer  
lighter  
stronger  
sharper  
greenish  
CONTRAST  
SHARPNESS  
*TINT  
100  
50  
purplish  
* TINT is for NTSC system only.  
The adjusted level is stored in the PERSONAL position.  
13  
OPERATION  
Convenient Sound Controls and Sleep timer  
Adjusting the volume and muting the sound  
To adjust the volume  
Adjust the volume with the VOL  
buttons.  
Press the VOL button to decrease the sound.  
Press the VOL button to increase the sound.  
To mute the sound  
The muting function is convenient when you need to pay attention  
to surrounding sounds, answer a phone call, receive a visitor, etc.  
1.  
Press the MUTE button to mute the sound.  
MUTE  
2. To restore the sound, press the MUTE button again or VOL  
buttons.  
Sleep timer  
SLEEP timer  
Making use of the Sleep timer function allows you to have the set  
automatically turned off after a preset time, and the TV set set to  
standby mode.  
Press the SLP button every time, the time displaying  
on the screen will change in the sequence below:  
SLEEP:30MIN.  
120MIN  
110MIN.......... 10MIN  
OFF  
14  
OPERATION  
System setting  
SYSTEM SET  
Press the MENU button repeatedly to select and  
highlight the icon, and the SYSTEM SET  
menu appears on the screen automatically.  
ENG/  
AUTO  
BG  
LANGUAGE  
C.SYSTEM  
S.SYSTEM  
B.B.SET  
ON  
SELECT  
ADJUST  
To select the language for the OSD  
Making use of this function can switch the language for the OSD to either  
English or Chinese.  
In the  
button to select LANGUAGE. Press the  
button to select ENGLISH or " " (CHINESE).  
(SYSTEM SET) menu, press the or  
ENG/  
AUTO  
BG  
LANGUAGE  
C.SYSTEM  
S.SYSTEM  
B.B.SET  
or  
ON  
SELECT  
ADJUST  
The selected language is displayed in front and the  
screen menu is automatically displayed in that  
language  
Colour system selection  
In  
button to select C-SYSTEM item.  
Press the or button to select proper colour  
(SYSTEM SET) menu, press the or  
ENG/  
AUTO  
BG  
LANGUAGE  
C.SYSTEM  
S.SYSTEM  
B.B.SET  
system, AUTO, PAL, 443NTSC, 358NTSC can be  
selected cyclically (refer to setting of colour  
system on page 11).  
ON  
SELECT  
ADJUST  
Blue background  
With the blue background function ON, the TV will automatically  
turn blue when no signal is being received.  
ENG/  
AUTO  
BG  
LANGUAGE  
C.SYSTEM  
S.SYSTEM  
B.B.SET  
In  
(SYSTEM SET) menu, press the or  
or  
button to select B/B SET. Press the  
button  
to change the blue background setting ON or OFF.  
To exit the menu, press the MENU button repeatedly or  
wait for 15 seconds.  
ON  
SELECT  
ADJUST  
Note: If the receiving signals are weak or are not standard, please set the B.B.SET to OFF, otherwise blue  
back will appear on the screen or the program will be lost.  
15  
OPERATION  
Special functions  
CALENDAR function (1800-2200)  
Enter into the  
menu, press the or button to select  
CALENDAR, press the  
enter into calendar interface.  
(SPECIAL FUNCTION)  
CALENDAR  
GAME1  
GAME2  
or  
button to  
In the calendar interface pressing the or  
button can switch among the year, month and  
SELECT  
ADJUST  
the date while pressing the  
increment or decrement them.  
or  
button can  
JULY 18 2007  
SU MO TU WE TH FR SA  
To exit the calendar interface, press any one of the buttons on the  
remote controller  
3
1
8
2
9
6
4
5
7
10  
17  
24  
31  
13  
20  
27  
11  
18  
25  
12  
19  
26  
14  
21  
28  
15 16  
22 23  
29 30  
Playing games  
To play GAME1 (GOBANG)  
Enter into the  
menu, press the or button to select  
GAME1 item, press the  
enter GAME1 interface  
(SPECIAL FUNCTION)  
CALENDAR  
GAME1  
GAME2  
or  
button to  
SELECT  
ADJUST  
To play GOBANG, that is, you play chess with  
the machine, Whoever first fills the chessboard with five  
continuous chessmen at the same line or diagonal line will win the  
game. Pressing the  
,
,
,
buttons can move the cursor  
upward or downward or leftward or rightward. Press the MENU  
button to confirm the position.  
To exit the game, press the VOL  
button or the CH  
button.  
16  
OPERATION  
Special functions  
Playing games  
To play GAME2 (Falling Cube)  
Enter into the  
menu, press the or button to select  
GAME2 item, press the  
enter GAME2 interface.  
(SPECIAL FUNCTION)  
CALENDAR  
GAME1  
GAME2  
or  
button to  
SELECT  
ADJUST  
Press any one of  
screen, there are falling cubes, pressing  
cubes shape, pressing buttons can move the cubes  
,
,
,
buttons to start the game. on the  
button can change the  
,
leftward or rightward while pressing  
falling speed.  
button can quicken the  
When at the screen's playing area one row has been filled with cubes, the row will disappear, and  
your score will gain one point. If two rows disappear at the same time, your score will gain three points.  
If three rows disappear at the same time, you score will gain seven points.  
The right window provides hints about next cube's shape, you can arrange current cube's position and  
and angle in advanced. When the cube reach top, the screen will display GAME OVER, and the game is  
finished.  
To exit the game, press the VOL  
button or the CH  
button.  
17  
OPERATION  
CLOCK SETTING  
CLOCK SET  
Press the MENU button repeatedly to select and highlight the  
appears on the screen automatically.  
icon, and the CLOCK SET menu  
NOW TIME setting  
Making use of this function can set the current time for the TV.  
In the  
(CLOCK SET) menu, press the or  
18:30:18  
NOW TIME  
ON TIME  
OFF TIME  
ON CHANNEL  
TIME ADJ  
OFF  
OFF  
--  
button to select NOW TIME. Press the  
button to set the current time  
or  
0M  
SELECT  
ADJUST  
ON TIME setting  
Making use of this function can automatically turn on the TV at a  
preset time.  
In the CLOCK SET menu press the or button to select ON  
18:30:18  
19:00  
OFF  
000  
0M  
NOW TIME  
ON TIME  
OFF TIME  
ON CHANNEL  
TIME ADJ  
TIME. Press the  
or  
button to set the TV ON time. In  
standby mode, once the TV ON time is in accordance with the  
current time, the TV will turn on automatically.  
SELECT  
ADJUST  
OFF TIME setting  
Making use of this function can automatically turn off the TV at a  
preset time.  
In the CLOCK SET menu press the or button to select OFF  
18:30:18  
OFF  
23:00  
000  
NOW TIME  
ON TIME  
OFF TIME  
ON CHANNEL  
TIME ADJ  
TIME. Press the  
or  
button to set the TV OFF time. In  
standby mode, once the TV OFF time is in accordance with the  
current time, the TV will turn off automatically and be in standby  
mode.  
0M  
SELECT  
ADJUST  
ON CHANNEL setting  
Making use of this function can automatically turn on the TV at a  
preset channel  
In the CLOCK SET menu press the or button to select ON  
18:30:18  
19:00  
OFF  
008  
0M  
NOW TIME  
ON TIME  
OFF TIME  
ON CHANNEL  
TIME ADJ  
CHANNEL. Press the  
or  
button to set the TV ON channel.  
If the set's turning on is determined by the ON TIME setting, then  
after turning on, the TV will broadcast the preset channel.  
Note:  
SELECT  
ADJUST  
1) To fulfill the ON CHANNEL function, you should set ON TIME first.  
2) Press the  
or  
button to set the time. If you press the button within 0.7 seconds, the minute  
will increase or decrease by 1; if you press the button for more than 0.7 seconds, the  
minute will increase or decrease by 20.  
3) Once the function of ON/OFF TIME has been fulfilled, next when you want to use the function  
once more you should set them again.  
Time adjustment  
Making use of this function can adjust the built-in clock.  
In the CLOCK SET menu press the or button to select TIME  
18:30:22  
OFF  
OFF  
--  
-10M  
NOW TIME  
ON TIME  
OFF TIME  
ON CHANNEL  
TIME ADJ  
ADJ item. press the  
or  
button to adjust the value. If you  
discover the built-in clock is quicker or slower than standard time,  
for example, every day it will be quicker for about 10 minutes, then  
you can set the value to -10 MIN to adjust the clock  
SELECT  
ADJUST  
To exit the menu, press the MENU button repeatedly or wait 15 seconds.  
18  
OPERATION  
Channel reservation  
To reserve the channel  
Making use of this function can switch the channel to your desired  
channel you reserve at a preset time.  
OFF  
--  
TIME  
CHANNEL  
Press the MENU button repeatedly to select and  
highlight the  
icon, and the RESERVE menu  
appears on the screen automatically  
SELECT  
SET  
Time setting  
Making use of this function to set the time to switch the channel to  
the reserved channel.  
19:28  
TIME  
Press the or button to select TIME.  
000  
CHANNEL  
Press the  
or  
button to set the time.  
To exit the menu, press MENU button repeatedly or  
wait 15 seconds.  
SELECT  
SET  
Channel setting  
Making use of this function to set the reserved channel.  
19:28  
TIME  
Press the or button to select CHANNEL, then  
press the or button, the channel number.  
When the set's current time is in accordance with the  
time which you set in the (RESERVE) menu,  
005  
CHANNEL  
SELECT  
SET  
the set will automatically switch to the reserved  
channel.  
To exit the menu, press the MENU button repeatedly or wait for 15 seconds.  
Note:  
1. To fulfill the RESERVE function, you should set the time firstly, the set the reserved channel.  
2. Once the RESERVE function has been fulfilled, next when you want to use the function once  
more, you should set them again.  
19  
CONNECTING OTHER EQUIPMENT  
External Equipment Connections  
.
The following describes how to use and connect the TV with other AV equipment. Refer to  
the owner’s manual of the equipment to be connected as well.  
To connect AV input terminal  
You can connect video equipments such as a VTR and video camera to this TV and enjoy the high  
quality picture and sound.  
If your video equipment has a S-VIDEO output terminal, connect it to the S-VIDEO input terminal  
(special S-VIDEO type) of the unit. If not, connect it to the VIDEO terminal (photo type).  
20  
CONNECTING OTHER EQUIPMENT  
To connect AV input terminal (continued)  
To select the video input, press TV/AV the button on the TV set or AV button on the remote controller  
repeatedly until you see the corresponding input indication on the screen. To return to aerial input,  
press the AV button until it displays program number, or press channel select button or the CH  
button.  
VIDEO 3  
TV  
VIDEO 1  
VIDEO 2  
(S-VIDEO)  
If the colour of video input is abnormal, the colour system setting may be incorrect. Press the SYS  
button until the COLOR AUTO is displayed on the screen. If the picture is still abnormal,  
press the  
or  
button until normal colour appears.  
NOTE on the S-VIDEO terminal  
The S-VIDEO input terminal has priority over Video 1 VIDEO terminal. If S-VIDEO input terminal is  
used, the screen will display "S-VIDEO1". To use the equipment connected to AV1 VIDEO terminal,  
disconnect any plug from the S-VIDEO terminal  
To connect MONITOR output terminal  
You can connect a stereo system to the MONITOR output terminals (photo type) on the set to  
enjoy a high-quality sound from the stereo system. The MONITOR output terminals output the  
video and audio signals being displayed on the screen.  
21  
OTHERS  
Troubleshooting Guide  
.
Before calling service personnel, please check the following chart for a possible cause to the  
trouble you are experiencing.  
Check the following items  
Symptoms  
No power, red indicator is not lit up  
Poor colour, poor tint  
.
.
Be sure the power cord is plugged in.  
Contrast, colour, tint are not correctly  
adjusted  
.
.
Possible interferences of automobiles,  
motorcycle, trolley bus, neon lamps, etc.  
Possible interference of electronic  
interference from another TV set, a  
computer, an electronics game machine, a  
broadcast station, etc.  
Spots appear on the screen  
Stripes appear on the screen  
.
This may be caused by reflections from  
nearby mountains or buildings.  
Check the antenna direction.  
Double images or "ghosts"  
Snowy picture  
.
.
It is possible that the aerial “lead-in” is  
damaged or comes off.  
Check the antenna direction  
.
.
The batteries may be worn out.  
The batteries may be installed with their  
polarity reversed.  
.
The remote controller does not work  
.
Even if the picture or the sound is normal,  
changes in the room temperature  
sometimes make the TV cabinet expand or  
contract, making a noise. This does not  
indicate a malfunction.  
TV cabinet creaks  
Specifications  
AC 240V, 50Hz  
140W  
737 (W) x 610 (H) x 519 (D)  
45  
Power supply:  
Power consumption:  
Dimensions (mm):  
Weight (kg):  
71cm  
CRT  
TV system & channel range  
UHF  
21-69  
CATV  
X~Z+2, S1~S41  
System  
PAL-B/G  
VHF  
2-12  
PAL-BG, NTSC 3.58/4.43 (AV)  
5W + 5W  
Colour system:  
Sound output:  
Accessory:  
one remote controller  
* Note: Design and specifications are subject to change without notice.  
22  
PALSONIC CORPORATION PTY LTD  
1 JOYNTON AVENUE  
WATERLOO NSW 2017 AUSTRALIA  
TEL:(02)9313 7111  
FAX:(02)9313 7555  
PALSONIC CUSTOMER SERVICE  
TELEPHONE  
AUSTRALIA: 1300 657 888  
604-25AA3-09  

Iiyama Computer Monitor E2201W User Manual
Iiyama MA203DT D User Manual
Intel PENTIUM MB893 User Manual
Motorola System Expansion Cordless Handset SD4502 User Manual
NEC PlasmaSync 42XC10 User Manual
Panasonic CT 36HX41 User Manual
Philips 28PT4421 User Manual
Philips Brilliance 200P3G User Manual
Philips Computer Monitor 220V3 User Manual
Philips DVD Player DVP2880 User Manual