Oricom ECO70 User Manual

Oricom eco Series  
USER GUIDE  
eco700 DECT Digital Cordless  
Telephone with Answering  
System  
eco70 DECT Digital Cordless  
Telephone  
Keep this user guide for future reference.  
WARNINGS AND SAFETY INFORMATION 1  
The earpiece of the handset may attract small metal  
objects such as staples and pins. Care should be taken  
when placing the handset near these items.  
This telephone is not designed for making emergency  
telephone calls when the mains power fails.  
Always have a corded phone available to be able to make  
and receive calls to emergency services if the mains power  
fails.  
Do not use your telephone during an electrical storm  
thunderstorm as it is possible to get an electric shock.  
IMPORTANT  
Avoid exposure of this telephone to moisture or liquid.  
To prevent electric shock, do not open the handset or base  
cabinet.  
Avoid metallic contact (e.g. metal clips, keys) between the  
battery contacts and charging conductors.  
There is a slight chance that the telephone could be  
damaged by an electrical storm. It is recommended  
that users unplug the phone from the mains supply and  
telephone socket during a storm.  
Refer to information contained in White pages directory.  
This phone is designed for connection to a PSTN telephone  
line or an analogue extension port of a PBX system. If you  
connect this device to a digital extension of a PBX, damage  
may result to the PBX.  
Do not use the handset in an explosive hazard area such  
as where there is gas leaking.  
Follow the local regulations regarding the disposal of your  
packing materials, exhausted batteries and used phone.  
Wherever possible, recycle those materials.  
We advise that this phone should not be used near  
intensive care medical equipment or by persons with  
pacemakers.  
Clean with a dry, soft, lint-free cloth. Never use cleaning  
agents, particularly aggressive solvents.  
Because the phone works by sending radio signals between  
base station and handset, wearers of hearing aids may  
experience interference in the form of a humming noise.  
Your phone can interfere with electrical equipment such  
as answering machines, TV and radio sets, clock radios  
and computers if placed too close. It is recommended that  
you position the base unit at least one metre from such  
appliances.  
This telephone complies with applicable safety  
requirements for exposure to radio waves (EMR). The mean  
power of this telephone does not exceed 20mW limit at  
which point testing is required.  
CAUTION  
Use only the mains adaptors supplied with this product.  
Incorrect adaptor polarity or voltage can seriously  
damage the unit.  
!
Adaptor for base unit:  
eco70  
Input: 100-240VAC 50/60Hz 200mA  
Output: 6VDC 300mA  
eco700  
Input: 100-240VAC 50/60Hz 200mA  
Output: 6VDC 500mA  
eco70&700 charger (eco7050):  
Input: 100~240VAC 200mA;  
Output: 7.5VDC 100mA;  
2 GETTING STARTED  
Installation and Charger  
WARNING  
1. Connect the mains adaptor (supplied)  
to the socket on the back of the base  
unit and to the wall mains supply.  
2. Connect the telephone cord to the  
phone socket on the back of the base  
unit and into the wall phone socket.  
DO NOT USE STANDARD/ALKALINE BATTERIES IN  
THIS PRODUCT, AS THERE IS A RISK OF EXPLOSION  
AND/OR INJURY. USE ONLY NI-MH RECHARGEABLE  
BATTERIES AS SPECIFIED IN THIS USER GUIDE.  
CONTACT ORICOM FOR REPLACEMENT BATTERIES.  
!
RISK OF EXPLOSION IF BATTERY IS REPLACED BY  
AN INCORRECT TYPE.  
Never use non-rechargeable batteries. Use recommended  
type supplied with this product.  
3. Insert 2 rechargeable Ni-MH AAA  
batteries (included), observing the  
correct polarity, into the battery compartment on the  
handset. Slide the battery door firmly into place.  
Never use alkaline or lithium batteries.  
Do not dispose of the batteries in a fire, as they can  
explode.  
4. Place the handset on the charging cradle and charge  
the batteries for a full 14 hours before using it for the  
first time.  
Do not open or mutilate the battery. Released  
electrolyte is corrosive and can cause damage to the  
eyes or skin. It can be toxic if swallowed.  
Avoid contact with metal objects when handling the  
battery. These objects could short out the batteries or  
cause the conductor to overheat resulting in burns.  
Note:  
It may take some time for the cordless handset to power  
up, and it may get warm during initial charge. This is  
normal.  
Do not attempt to recharge the battery cell by heating  
it. Sudden release of battery electrolyte can cause  
burns or irritation to the eyes or skin.  
Observe the proper polarity, or direction, of any battery.  
Reverse insertion of the battery cell can result in  
leakage or explosion.  
Tip!  
It is good practice to put the cordless handset on the  
charging cradle when it is not in use to ensure that the  
handset is always fully charged.  
Remove the batteries if you do not plan to use the  
product for several months at a time.  
Follow the local regulations regarding the disposal of  
your packing materials, exhausted batteries and used  
phone. Wherever possible, recycle those materials.  
GETTING STARTED 3  
Pack contents  
Purchasing additional handsets  
Depending on the model you have purchased this pack You may expand your eco70/700 by adding more handsets  
should contain the following items:  
(eco7050). These can be purchased separately from the  
retailer where you purchased the product, or directly from  
Oricom (Australia). The eco70/700 can accommodate a  
total of 5 cordless handsets.  
If any of these are missing, please contact Oricom directly.  
eco70/700-1 eco70/700-2  
Base units  
1
1
1
Important:  
Do YoU HaVE BroaDBanD/aDSL?  
Cordless handsets  
2
If you do, you must connect an in line filter (not supplied) between  
the telephone socket and your eco70/700 base to ensure that your  
broadband and eco70/700 will work properly. If you do not install  
the filter you will experience interference on the eco70/700 and your  
Broadband may suffer dropouts. Please refer to the user guide of the  
in line filter for installation.  
Charging cradle and power  
adaptor  
0
1
Power adaptors  
Line cord  
1
1
1
1
1
1
User guide  
Handset Rechargeable AAA  
Ni-MH Batteries (1.2V 500mAh)  
2
4
4 GETTING STARTED  
Your cordless handset  
1 LCD Display  
2 Talk  
3 Left / Recall / Dial mode  
4 Handsfree  
1
6
5 Phonebook  
6 Right / CID (Caller ID)  
7 Intercom  
2
3
7
8
4
5
8 Delete / Mute  
9 Numeric keys  
10 / Ringer Off (On)  
*
9
11 Ringer Melody / Ringer Volume / Receiver Volume  
12 # / Keypad lock  
10  
11  
12  
13  
13 LNR (Last Number Redial) / Pause /Long (Short)  
flash  
GETTING STARTED 5  
Answering machine (eco700)  
1 Talk/Charging state indication  
2 LCD Display  
1
3 Number or Character indication  
4 Power supply indication  
5 Speaker Volume down / Ring  
6 Speaker Volume Up / Code  
7 Power On/Off /Stop  
8 Delete  
2
3
4
5
6
7
8
9
10  
11  
12  
9 OGM / Rewind  
10 Fast Forward / MEMO  
11 Page  
12 Play / Pause/ Clock  
6 GETTING STARTED  
eco700  
1
2
1 Connected with DC adaptor  
2 Connected with telephone cord  
eco70  
1
2
GETTING STARTED 7  
Understanding the cordless handset display  
Left Arrow / Phonebook records are being  
reviewed  
Battery level (3 bars fully charged)  
Ringer is turned off  
Speakerphone on  
Keypad lock  
Connected to telephone line  
Flashes when there is an incoming call  
X appears: microphone muted  
Caller display  
Antenna in range / out of range  
Intercom call to another handset  
Right Arrow / Message waiting  
8 BASIC OpERATION  
During standby  
Answering an incoming call  
When there is an incoming call, the phone rings and flashes  
Note:  
on the display. If a CID record is received,  
caller information is displayed.  
flashes and the  
If the power is not connected to the base unit.  
The cordless handset CANNOT operate.  
1. Press [  
2. Press [  
] key to answer the call.  
] key again to end the call.  
Cordless handset's LCD display  
HANDSET 1 : Handset number  
: Current battery level  
Making an external call  
Normal dialling  
: A constant signal icon indicates the  
cordless handset is linked to the base unit.  
When signal icon is flashing the handset  
needs to be re-registered.  
1. Press [  
] key.  
2. Enter a telephone number. If you enter more than 12  
digits, you only see the last 12 digits on the display.  
3. Press [  
] key to end the call.  
Pre-dialling  
1. Enter a telephone number.  
2. When necessary, press [  
individually.  
] to erase the digit  
Note:  
The signal icon will also flash if the handset is out of range.  
3. Press [  
4. Press [  
] key to dial.  
] key to end the call.  
BASIC OpERATION 9  
Mute feature  
Checking the signal strength  
Place a call on hold so that the caller will NOT be able to The signal icon  
displays the link status between your  
hear you but you can still hear the caller.  
handset and the base unit. A steady icon means your  
handset and the base unit are linked. A flashing icon  
means your handset and the base unit are not linked.  
During talking mode,  
1. Press [  
] key on the handset to mute the call,  
is  
If you move too far away from the base unit while you are  
on the phone, you will hear warning tones notifying you that  
your handset is almost out of range – lost link. Take your  
handset closer to the base unit or your call may be cut off  
shortly after the warning  
shown on the display.  
2. Press [ ] key again to resume the call.  
Handset range  
Your eco70/700 handset has a range of up to 300 metres  
outdoors and up to 50 metres indoors, in ideal conditions.  
Note:  
If your handset has lost the link with the base, you will not  
be able to make or receive calls. You will also not be able  
to carry out many of the phone functions and features.  
If you carry the handset too far away from the base, you  
may go out of communication range and the antenna icon  
will flash on the display.  
If you are already on a call and move out of range, the call  
quality will degrade as the range limit is reached and the  
call may be disconnected. You will need to move closer  
to the base to be able to continue the call and make any  
further calls.  
Important notE:  
Emergency Call. This telephone is not designed for making  
emergency telephone calls when the power fails. Alternative  
arrangements should be made for access to emergency services.  
10 BASIC OpERATION  
Recall selection  
Handsfree mode  
You can use the Recall button on your telephone when using During talking or standby mode,  
your network operator's services such as call waiting etc.  
1. Press [ ] key to switch to speakerphone mode.  
2. Press [ ] key again to cancel this feature.  
A subscription may apply for these services. Contact your  
network operator for more information. If this is not working  
correctly, change the setting using the instruction below:  
Volume adjustment  
Selecting recall duration:  
During standby mode adjust the handset ringer volume.  
1. Press and hold [  
] for 3 seconds.  
1. Press [  
2. Press [  
] key.  
] or [  
2. The display will show “Lor “S”  
(L: New Zealand ; S: Australia).  
] key to adjust the handset volume  
level, there are 5 volume levels and Volume off for  
selection.  
During handset talking mode adjust the handset receiver  
volume.  
Press [  
] key repeatedly to adjust the handset volume  
level (5 volume levels).  
CALLER ID OpERATION 11  
If you subscribe to your telephone operators service 1. Press [  
] key.You will hear a dial tone.  
(charges may apply), numbers of the incoming calls will be  
displayed on the screen and stored in the call log (please  
consult your telephone service provider for details).  
2. Press [ 2 ] to put the current call on hold and talk with  
the second caller.  
3. Repeat steps 1-2 to swap between the two callers.  
The eco70/700 series can store the last 20 calls including:  
the record number, date/time, and phone number (up to 23  
digits for the cordless handset).  
Review Caller ID records  
During standby mode,  
When you have new/unanswered calls,  
flashes on the  
cordless handset. If a call has been answered, then the call  
is set to old call.  
1. Press [  
] key to display the latest call. The following  
will appear on the display.  
45748888  
Call waiting (Australia only)  
You can use the recall function to answer a second call  
while you are on the phone. However this service needs to  
be turned on. For example, to turn on Telstra’s Call Waiting  
service:  
If the list is empty, NO” is shown on the display.  
2. Press [  
] key to view the data and time of the CID.  
3. Press [  
Press [  
] key to view to the previous call.  
] key to view the next call.  
1. Press [  
] on the cordless handset to wait for dial tone  
then press [ ] [4] [3] [#].  
Only when the network sends the time/date together with  
the telephone number! On some networks with caller ID,  
time and date will not be displayed.  
2. You will hear a service tone then press [  
] again.  
Take two different calls at the same time  
During a call, you will hear two loud beeps periodically to  
notify you of another incoming call. If you wish to answer  
this call,  
12 CALLER ID OpERATION  
Store a CID number  
Delete CID record(s)  
You can save a CID record into the Phonebook/Direct While you are viewing the CID record that you wish to  
memory provided that it contains a valid phone number and delete,  
the Phonebook/Direct memory is not full.  
Press and hold [ ] key for about 3 seconds.  
While you are viewing the CID record that you wish to save,  
Note:  
1. Press and hold [  
] key for about 2 seconds. The  
If there are no more CID records, a message “NO” is  
displayed.  
following will appear on the display.  
_
45748888  
Calling a number from the CID records  
2. The space after the last digit of the CID will blink, and  
press the numeric keys to edit the CID number and then  
When you are viewing the CID records,  
1. Press [  
2. Press [  
] or [  
] key to scroll to desired number.  
press [  
] key to confirm.  
] key. The number will be dialled automatically.  
3. Press the memory location no. that you want to store  
the number. It will then give a beep to confirm that the  
storage is successful.  
4. Press [  
] key again to confirm and go back to standby  
mode.  
The record is now saved into the phonebook. Then it goes  
back to the call log.  
LNR FuNCTION (LAST NuMBER REDIAL) 13  
2. The space after the last digit of the Redial number will  
Redial the last number  
blink, and you can press numeric keys to edit the Redial  
number. Then press [ ] key to confirm.  
Your cordless handset stores the last 3 external numbers  
dialled, up to 24 digits per number. If the number exceeds  
24 digits, the last 24 digits will be stored to memory.  
3. Press the numeric keys to edit the memory location (0-9)  
where you want to store the number. You will hear a  
confirm beep.  
During standby mode,  
4. Press [  
] key again to confirm and go back to standby  
1. Press [  
2. When necessary, press [  
selected your desired number.  
3. Press [  
] key.  
mode.  
] key again until you have  
The record is now saved into the phonebook. Then it goes  
back to the call log.  
] key to dial.  
Or  
Delete last number dialled  
1. Press [  
2. Press [  
] key.  
While you are viewing a previously dialled number that you  
wish to delete,  
] key to redial the last number.  
Press and hold [ ] key for about 3 seconds.  
Store the last number dialled  
While you are viewing a previously dialled number that you  
wish to save,  
Note:  
If there are no more LNR records, a message “NO” is  
displayed.  
1. Press and hold [  
] key for about 2 seconds. The  
following will appear on the display.  
_
45748888  
14 phONEBOOk  
Add new records  
Review / Edit / Dial stored Phonebook  
records  
You can store up to 10 phonebook records in each handset.  
Each record can contain up to 24 digits per number.  
During standby mode,  
During standby mode,  
1. Press [  
] key. The following will appear on the display.  
1. Press and hold [  
] key until the  
icon appears on  
the display.  
2. Press the numeric keys to enter the telephone number.  
If you made a mistake, press [ ] key to edit it. Press  
and hold [ ] key to delete the entire number.  
2. Press the numeric keys to view the stored records.  
3. Press [ ] key to dial the number.  
3. Press [  
] key to confirm.  
4. Press the numeric keys to enter the memory location  
(0-9) where you want to store the number.  
5. You will hear a confirmation beep.  
The record is now saved into the Phonebook. Then it goes  
back to standby mode. Repeat step 1 to 5 to add another  
record.  
While you are viewing the record that you wish to edit,  
1. Press and hold [ ] key. The following will appear on  
the display The space after the last digit will blink.  
.
_
245748888  
2. Press [  
] key to erase the entire digits.  
3. Press [ ] key to confirm.  
] key to erase the last digit, or press and hold  
[
CORDLESS hANDSET OpERATION 15  
1. Press and hold [  
2. Press [ ] or [  
(1 to 9 for adjustment).  
3. Press [ ] key to confirm.  
] key.  
Voicemail indication – network service  
] key to select the melody option  
Note:  
Volcemail Indication Service. Requires subscription with  
your netwok service provider.  
Handset ringer volume  
During standby mode,  
Voicemail indication is a visual voicemail alert. On this  
1. Press [  
level.  
] key. Display shows the current volume  
phone, you will see an envelope  
icon when there is a  
voicemail waiting in your service providers mailbox.  
2. Press [  
] or [ ] key to select the volume level.  
There are 5 levels for adjustment: 1 (lowest) to 5 (highest)  
Retrieving Voicemail(s)  
To retrieve your voicemail(s), consult your service provider.  
and Volume off (the [  
display).  
] icon will be shown on the  
Clearing the Voicemail indicator  
3. Press [  
] key again to confirm.  
After checking your voicemail(s), the voicemail indicator  
will be cleared automatically after receiving a signal  
from the network. You can clear the voicemail indicator  
manually if it fails to reset.  
Handset ringer On / Off  
During standby mode, press and hold [  
between ringer On/Off.  
] key to switch  
1. Remove the batteries of the handset unit. Wait for 30  
seconds. Insert batteries again, the voicemail indicator  
will be cleared.  
Handset ringer adjustment  
appears whenever the ringer is Off.  
Handset ringer melody  
During standby mode,  
16 CORDLESS hANDSET OpERATION  
2. Key the handset number (2, 3, 4 or 5) you wish to  
Multi-handset Operation  
transfer.  
Your eco70/700 series phone can have up to 5 handsets  
registered to the base unit. Each handset has its own number  
HS-1, HS-2, HS-3, HS-4 and HS-5, shown on the left-hand  
side of the display. With 2 or more handsets you can:  
3. Press [  
] key to exit Intercom mode and return to  
standby mode.  
Conference calls  
This function allows 3 parties (yourself + external call +  
intercom call ) to be connected at the same time.  
Make intercom calls while on an external call  
Switch between an external call and intercom call  
Transfer an external call from one handset to another  
Set a 3-way conference call between yourself, an  
external call and intercom call  
During external call,  
1. Press [ INT ] key. The following will appear on the display.  
Note:  
• A maximum of 1x external call and 2x intercom calls can  
take place at the same time.  
• If you make an external call + another handset is on line  
= result in a busy tone.  
You can make an intercom call when the other handset is  
2. Key the handset number (2, 3, 4, 5) you wish to invite to  
the conference.  
3. Then you can have an intercom call with HS-x.  
4. At this moment, you can press and hold [INT] key for 3  
seconds to go to 3-way conference call.  
in progress.  
Call transfer between cordless handsets  
During external call,  
Cordless handset keypad lock  
During standby mode,  
1. Press [ INT ] key. The following will appear on the display.  
1. Press and hold [  
] key to lock the keypad.  
2. To release keypad lock, press and hold [  
] key for 3  
seconds.  
CORDLESS hANDSET OpERATION 17  
Note:  
When the keypad is locked, [  
] key and [ INT ] key can  
be used to answer an external or intercom call.  
2. Press 1 and the handset begins to search for the base.  
3. Enter the base pin code (0000). If the pin is wrong, the  
Registration  
handset will restart searching for the base.  
4. When the handset is registered, it will show “HS”followed  
by the handset number.  
Register new handsets on the eco70/700 base  
The handsets which come in the same pack are already  
registered to the base. If you buy new handsets. You need  
to register them before use.  
Note:  
If the base is full and cannot add any more handsets, you  
will hear a tone. See the next section to remove a handset.  
1. Charge the batteries (for 14 hours).  
2. Register the handset (to the base unit).  
Remove handsets  
During standby mode,  
the operation is different in eco70 and eco700.  
1. Press and hold the [  
and hold the [ ] key for 3 seconds.  
2. Enter the default value 0000. If the pin is wrong, the  
handset will go back to standby.  
3. Press the numeric keys (1-5) to enter the handset number  
you want to remove.  
] key for 3 seconds, then press  
In eco70, we need to set the base unit in registration mode  
by resetting the base power.  
In eco700, we can set the base in registration mode by  
pressing and holding the base [  
] for 10s  
Each base can register up to 5 handsets.  
During standby mode,  
4. The unit will go back to standby if the removal is  
successful.  
1. Press and hold the [  
the [ ] and [ ] icons flash, then press and hold the  
] key for 3 seconds. The following will appear on  
] key for 3 seconds until both  
Note:  
[
You can only remove other handsets in your system but  
you are not able to remove the handset you are using.  
the display.  
18 ANSWERING MAChINE OpERATION (ECO700 ONLY)  
The base has a built-in digital answering machine with  
a recording capacity of 11 min. The answering machine  
Outgoing Messages  
can be operated remotely and features the possibility of  
recording two outgoing messages (OGM 1 and OGM 2)  
(maximum of 2 min).  
Two outgoing messages of 2 minutes can be recorded  
(OGM1 and OGM2).  
Outgoing message 1 for the answering function and  
possibility for callers to leave a message.  
There are 2 possibilities:  
Outgoing message 2 for the answering function without  
allowing callers to leave a messages on the machine.  
With OGM 1, the caller has the possibility to leave a  
message  
With OGM 2, only the outgoing message is given  
without the caller having the opportunity to leave a  
message  
Recording outgoing messages (OGM 1 or OGM 2)  
Press and hold the [  
Press the [ ] key for two seconds.  
Record the outgoing message after the beep.  
Press the Stop key [ ] to stop recording.  
] key to select the OGM.  
The max. recording time for each incoming message = 3  
min.  
An internal voice will state various information, such as day  
and time of the call. The language of the internal voice is  
stated on the packaging!  
Playback the Outgoing Message  
To check the outgoing message now set:  
LED Display  
Press the [  
] key.  
The LED display on the base indicates how many  
messages you have received. When there are new  
messages, the 2x 7 segment LED display on the base  
will blink and indicate the amount of new messages. If  
the answering machine is switched off, the LED display  
does not light up. "FL" will be shown on the display when  
the internal memory is full and no new messages can be  
recorded.  
Note:  
• It is only possible to select an outgoing message if the  
answering machine is turned on.  
• If the memory is full, only outgoing message 2 can be  
selected (only answering without recording messages).  
ANSWERING MAChINE OpERATION (ECO700 ONLY) 19  
Erasing the Outgoing Message  
Setting number of Rings  
Erase the outgoing message as follows:  
The number of rings after which the answering machine  
will answer calls can be set from 2 – 9 and TS (Toll saver).  
The standard setting is 3 rings. In Toll saver mode, the  
machine will answer after 5 rings if there are no new  
messages, and after 2 rings if there are new messages. If  
there are no new messages and you call your machine to  
check your messages remotely (See “Remote Operation”),  
you can hang up after the 2nd ring. You do not need to pay  
connection fees and you know that you do not have any  
new messages.  
Select the desired outgoing message by pressing and  
hold the [  
] key.  
Press the [  
] key to play the outgoing message.  
Keep pressing the [  
] key when the OGM is played  
back.  
Turning Answering Machine On/Off  
If the answering machine is on, the 2x7 segment LED  
display will light up and the machine will automatically pick  
up the line after a number of rings (see “Setting number of  
Rings” ).  
Briefly press the [  
current numbers of rings.  
] key. The display will show the  
Press the [  
ringing tones.  
Press the [  
] key for 2 secs to set the number of  
] or [ ] key to change the  
Press the [  
machine. The 2x7 segment LED will be turned on.  
Press the [ ] key again to switch off the answering  
] key to switch on the answering  
current number of rings.  
Confirm the setting by pressing the [  
] key.  
machine. The 2x7 segment LED will be turned off.  
If you do not press any keys for 3 seconds, the machine  
will revert back to the answering machine menu, without  
changing the settings.  
Note:  
• Even if the answering machine is off, the machine will  
automatically pick up after 16 rings in order to enable  
remote activation (see “Remote Operation” ).  
If there is a loss of power in the base, the number of  
rings will revert to 5.  
20 ANSWERING MAChINE OpERATION (ECO700 ONLY)  
Press [  
of the VIP code.  
Press the [  
The display will show the current set 3rd digit of the VIP  
code.  
] or [  
] keys to set the second digit  
Note:  
• If you do not press any keys for 3 seconds, the machine  
will revert back to the answering machine menu, without  
changing the settings.  
] key to confirm the second number.  
Press [  
the VIP code.  
Press the [  
] or [  
] keys to set the third digit of  
Checking number of Rings  
] key to confirm the VIP code. You will  
Press the [  
] key briefly.  
hear a long beep. The new code will be displayed digit  
by digit.  
The display will show the number of rings set.  
Programming the VIP Code  
Note:  
• If you do not press any keys for 8 seconds, the previous  
VIP code is saved and the machine automatically exits  
the VIP setting mode.  
The VIP code is a 3-digit code used to operate the machine  
remotely (see Remote Operation). The VIP code is set to  
"321" by default.  
Changing the VIP Code  
Checking the VIP Code  
Keep the [  
the VIP code.  
] key pressed down for 2 secs to change  
Press the [  
will show the VIP code digit by digit.  
] key to show the VIP code. The display  
The first digit of the VIP code is displayed blinking on  
the screen.  
Press [  
of the VIP code.  
Programming the Date/Time  
Press and hold the [  
first play the current Date/Time.  
Then, a short beep to start set date, prompt "Set day",  
] button for 2 seconds, it will  
] or [  
] keys to set the first number  
Press the [  
] key to confirm the first number. The  
pause then prompt current day. Press [  
] to select days.  
] or  
display will show the current set 2nd digit of the VIP  
code.  
[
ANSWERING MAChINE OpERATION (ECO700 ONLY) 21  
Press [  
] button to confirm setting and jump to next,  
Note:  
it will prompt "Set hour", pause then prompt current hour  
in 24 hours format. Press [  
hours.  
Press [  
next, it will prompt "Set minute", pause then prompt  
current minute. User would press [  
to select minutes  
Press [  
If, during pick-up, nothing is said for 8 seconds, the  
line will be automatically disconnected.  
] or [  
] to select  
The 2x7 segment LED will flash and alert the user  
that a new message is recorded.  
] button to confirm setting and jump to  
] or [  
]
Recording a Memo  
] button to confirm setting, it will prompt the  
You can record memos. These memos are considered an  
incoming message that can be picked up later by the user.  
The max. recording time for a memo is 3 minutes.  
newly set day, hours and minute then back to standby or  
off mode.  
Press the [  
say your memo.  
Press the Stop [  
] key for 2 seconds. After the beep,  
Operation  
If a call is received and the answering machine is turned  
on, the answering machine will automatically pick up the  
line after the set number of rings. If  
] key to stop recording.  
Playback of Incoming Messages and  
Memos  
Outgoing message 1 has been selected, it will be  
played. After the outgoing message, a beep will be  
heard and the caller can leave a message (of a max. 2  
minutes).  
Outgoing message 2 has been selected, it will be  
played. After the beep, the line will automatically be  
disconnected. The caller does not have the possibility to  
leave a message.  
Press the [  
] key to play the messages and memos.  
The messages are played one at a time. If there are new  
messages, only the new messages (those that have not  
been heard) are played.  
During playback, you can:  
– go to the beginning of the current message by pressing  
the [ ] key once.  
22 ANSWERING MAChINE OpERATION (ECO700 ONLY)  
– go to the previous message by pressing the [  
]
Memory Full  
key twice.  
If the memory is full, "FL" will flash on the display. If the  
answering machine is turned on and a call comes in, the  
machine will automatically play OGM 2 (answering machine  
function without recorded caller message).  
– stop playback by pressing the Stop [  
– interrupt playback by pressing the Pause key [  
Press the play [ ] key again to restart playback.  
] key.  
] .  
– go to the next message by pressing the [  
] key.  
Erase all the messages after listening to them.  
The memory is free again.  
Erasing Messages  
Erasing Messages One at a Time during Playback  
Start message playback as explained above.  
When the message to be erased starts playing, press  
the delete key [ ] for 2 secs  
The display will show "dL".  
Press the delete key [ ] again to confirm.  
Erase all messages  
One can also erase all heard messages at one time. This  
erases only the messages that have already been heard.  
New messages are not erased.  
Press the delete key [ ] for 2 secs.  
The display will show "dL".  
Press the delete key [ ] again to confirm.  
REMOTE OpERATION (ECO700 ONLY) 23  
The answering machine can only be operated remotely  
using a touch-tone phone (DTMF tone selection system).  
Playing Outgoing Message  
Press [ 4 ] to play the current outgoing message.  
Call your machine.  
The answering machine picks up the line, you hear the  
outgoing message and a beep.  
After the beep, slowly dial the VIP code (default 321).  
You will hear two short beeps for confirmation.  
Enter the next codes to use the desired function:  
Recording Outgoing Message  
Press [ 9 ] to select OGM 1 or OGM 2.  
Press [ 5 ] to start recording  
A beep will indicate that you can start recording.  
Say your message.  
Press [ 6 ] to stop recording.  
Listening to Messages  
Turning Answering Machine On/Off  
Press [ 2 ] (listen to messages). The answer machine  
will play the messages.  
During playback, you have the following options:  
Press the [ 9 ] key to switch on the answering machine.  
Press the [ 8 ] key to turn off the answering machine.  
Press [ 2 ] to stop playback.  
Press [ 2 ] to restart playback.  
Press [ 3 ] to go to the next message.  
Press [ 11 ] to go to the previous message.  
Press [ 1 ] to repeat the current message.  
Press [ 6 ] to stop playback.  
Ending Remote Operation  
If you want to end remote operation, press [ 6 ].  
Press [ 7 ] to erase the current message.  
Erasing All Old Messages  
After listening to all messages, press [ 0 ] to erase all  
messages.  
24 REMOTE OpERATION (ECO700 ONLY)  
Turning answering machine on remotely  
Keys on  
remote phone  
keypad  
Corresponding button on answer  
machine  
If the answering machine is switched off, you can turn it on  
remotely.  
1
2
3
4
5
6
7
8
9
0
*
RW  
Play/Pause  
Call your machine.  
The machine will pick up automatically after 16 rings  
and play outgoing message 2.  
After the beep tone dial the VIP code (default 321)  
slowly during the message plays.  
Press the '9' key. A long beep will be heard.  
Press [ 6] to stop operation.  
FF  
OGM playback  
OGM recording (press ‘Stop’ to stop)  
Stop  
Delete current message  
Answering off  
Answering on  
Delete all old messages  
Skip announcement  
Memo Recording  
#
CuSTOMER SuppORT 25  
If you feel this product is not working correctly please To order spare parts additional handsets, replacement  
consult the user guide and ensure that you are using the batteries and in case of any technical issues you may have  
product in accordance with the instructions. Remove all with this product please consult our website for further  
extra telephone equipment and connect only this telephone information or send us an email for a prompt response to  
directly to the telephone socket. If the fault is still present, your enquiry.  
connect another telephone (if available) to the telephone  
In the unlikely event of a fault developing, please contact us  
socket. The results will show you whether the fault lies with  
for assistance. If the product is then found to be faulty you  
this unit or with the telephone line.  
will be asked to return it directly to us with a copy of the  
If the product is working correctly the fault is on the purchase receipt.  
telephone line. Please contact your network operator for  
assistance.  
26 AppENDIx  
Troubleshooting  
Problem  
Possible cause(s)  
Solution(s)  
No dial tone on the  
cordless handset.  
1. The base unit is not properly connected.  
2. Too far from the base unit.  
3. Battery charge is low.  
1. Check CONNECTION to power and telephone line.  
2. Move handset CLOSER to base unit.  
3. CHARGE battery.  
4. Incorrect battery polarity.  
5. Re-register handset.  
4. RE-INSERT batteries and check + and .  
5. Handset not registered.  
Antenna symbol is flashing. 1. The handset is not registered. If the handset is  
1. REGISTER the handset.  
unregistered, it displays UNREGISTERED.  
2. The handset is out of range.  
2. Move CLOSER to the base unit.  
3. Check power CONNECTION to the base.  
3. The product is not properly connected.  
No beep when the cordless 1. The handset is not placed properly on the charger. 1. Lift handset off the charger carefully and REPOSITION  
handset is placed on the  
charger.  
correctly.  
2. Charging contacts are dirty.  
3. No power connection to base unit.  
4. The handset’s power is turned off.  
2. CLEAN charging contacts with a clean and dry cloth.  
3. Check power CONNECTION to the base.  
4. CHECK batteries.  
Handset charged for 24  
hours but Battery icon  
remains empty.  
1. Handset battery is defective or faulty.  
2. Handset is not placed properly on the charger.  
3. Battery installed incorrectly.  
1. REPLACE with new AAA rechargeable Ni-MH batteries.  
2. CHECK to make sure the battery icon is scrolling.  
3. RE-INSERT batteries and check + and .  
4. The product is not properly connected.  
4.Check power CONNECTION to the base.  
No symbol on the display.  
Can’t transfer a call.  
1. Battery is empty.  
2. The product is not properly connected.  
1. CHARGE battery.  
2. Make sure your product is properly PLUGGED-IN.  
1. Handset is busy.  
2. Handset is out of range.  
3. Wrong handset number.  
1. Check ALL handsets and END all calls.  
2. Move handset CLOSER to base unit.  
3. Check HANDSET NUMBER.  
AppENDIx 27  
Problem  
Possible cause(s)  
Solution(s)  
Bad audio quality  
(crackles,echo, etc.).  
1. Interference from nearby electrical appliance.  
2. Base unit is installed in a room with thick walls.  
3. The handset is too far from the base unit.  
4. If you have Broadband/ADSL you need a in line  
filter (not supplied).  
1. Try a different connection point, one that is away from other  
electrical appliances.  
2. Install the base unit in a DIFFERENT room OR use  
EXTENSION leads.  
3. Move CLOSER to the base unit.  
4. Ensure a in-line ADSL filter is installed on all phone sockets  
between wall plate and your phone.  
Caller ID does not work.  
Service not activated.  
1. The ringer is off.  
Check your SUBSCRIPTION with the SERVICE provider.  
Phone does not ring when  
1. Turn ON the ringer.  
a call comes in.  
2. Too many phones are sharing the same phone  
line.  
2. Disconnect some of the phones from the phone line.  
3. Check base unit CONNECTIONS.  
3. Base unit not plugged in.  
Keypad does not work.  
Keypad may be locked.  
UNLOCK the keypad.  
Busy tone + in use light on. 1. Other handset may still be connected.  
1. Check ALL handsets and END all calls.  
2. Check CONNECTIONS to wall and base.  
2. Check power supply connection.  
Handset registration fails  
The base memory may be full.  
Delete un-used handset and try again.  
continuously.  
Cannot make/answer a 2nd 2nd call service can be activated.  
Check with your service provider. Check the recall selection is  
call  
correct.  
28 AppENDIx  
Problem  
Possible cause(s)  
Solution(s)  
eco700 Answering System (ONLY)  
Answering machine does  
not record messages.  
1. The answer machine may be turned off.  
2. The memory may be full.  
1. Switch the answering machine on.  
2. Delete some messages.  
3. Answer mode may be set to ANSWER ONLY.  
3. Change the mode to ANSWER & REC.  
Cannot access messages  
remotely.  
1. Remote access may be switched off.  
2. Wrong PIN is entered.  
1. Switch Remote access on.  
2. Enter the PIN once again.  
Cannot record outgoing  
message.  
1. The memory may be full.  
1. Delete messages.  
Answering machine stops  
1. The memory may be full.  
1. Delete messages.  
recording part way through 2. The maximum message length is more than 2  
a message.  
minutes.  
Note:  
If none of the above solutions help, reset your phone by disconnecting the mains power from the base and removing batteries  
from handset/s. Reconnect after 15 minutes.  
Alternatively please contact Customer Service on (02) 4574 8888.  
AppENDIx 29  
Product Specifications  
Phone – Oricom eco70/700  
Frequency range  
Specifications  
1.88-1.897 GHz (bandwidth=20MHz)  
Channel bandwidth  
Operating range  
1.728 MH  
Up to 300m outdoors, up to 50m indoors  
Up to 100 hours  
Standby time  
Talk time  
Up to 10 hours  
Temperature time  
Operating 0ºC to 40ºC  
Storage -20ºC to 60ºC  
Compatibility  
Only GAP compatible DECT phones  
Up to 5 handsets per base  
Up to 4 bases per handset  
5 polytones + 4 monotones only  
Multiple handset capability  
Multiple bases  
Ringer melodies  
Included Accessories  
Battery charge time  
Rechargeable batteries  
14 hours  
AAA Ni-MH 1.2V 500mAh  
eco70  
Input: 100-240VAC 50/60Hz 200mA  
Output: 6VDC 300mA  
eco700  
Input: 100-240VAC 50/60Hz 200mA  
Output: 6VDC 500mA  
ECO70&700 charger (ECO7050):  
Input: 100~240VAC 200mA;  
Output: 7.5VDC 100mA;  
Mains power supply for base unit and charger  
30 AppENDIx  
to a replacement or repair according to the terms and  
conditions of this document if your product is found to be  
faulty within the Warranty Period. This Warranty extends to  
the original purchaser only and is not transferable.  
Warranty Information (Australia)  
Oricom makes no other warranties or conditions, express  
or implied, including as to merchantability and fitness for a  
particular purpose, except as stated in this Warranty. Any  
implied warranties that may be imposed by law are limited  
in duration to the Warranty Period.  
Oricom products are manufactured using new materials or  
new and used materials equivalent to new in performance  
and reliability. Spare parts may be new or equivalent to  
new. Spare parts are warranted to be free from defects  
in material or workmanship for thirty (30) days or for the  
remainder of the Warranty Period of the Oricom branded  
product in which they are installed, whichever is longer.  
Oricom warrants that the product is free from defects in  
materials or workmanship during the Warranty Period. This  
Warranty in no way affects your statutory warranty rights  
under the Trade Practices Act 1974 or any other similar  
legislation. This Warranty does not extend to any product  
from which the serial number has been removed, was  
purchased outside of Australia or that has been damaged  
or rendered defective:  
During the Warranty Period, Oricom will replace and where  
possible repair the defective product. All component parts  
removed under this Warranty become the property of  
Oricom.  
1. as a result of lightning, over voltage, accident, misuse,  
abuse or other external causes;  
2. the operation outside the normal use of the product;  
In the unlikely event that your Oricom product has a  
recurring failure, Oricom, at its discretion, may elect to  
provide you with a replacement product of its choosing that  
is at least equivalent to your product in performance.  
3. by the use of parts not manufactured or sold by Oricom;  
or  
Oricom does not warrant that the operation of the product  
will be uninterrupted or error free. Oricom is not responsible  
for damage that occurs as a result of your failure to follow  
the instructions that came with the product.  
4. by modification or service by anyone other than:  
(a) Oricom; or (b) an Oricom authorised service  
provider.  
These terms and conditions together with any specific  
terms and conditions contained in the user guide to the  
product purchased constitute the complete and exclusive  
agreement between you and Oricom regarding the product.  
The Warranty Period will be 12 months from the date of  
purchase of the product evidenced by your dated sales  
receipt. You are required to provide proof of purchase as  
a condition of receiving warranty services. You are entitled  
AppENDIx 31  
No change to the conditions of this Warranty is valid  
unless it is made in writing and signed by an authorised  
representative of Oricom.  
Notes for operation in New Zealand  
The grant of a Telepermit for any item of terminal equipment  
indicates only that Telecom has accepted that the item  
complies with the minimum conditions for connection to  
its network. It indicates no endorsement of the product  
by Telecom, nor does it provide any sort of warranty.  
Above all, it provides no assurance that any item will work  
correctly in all respects with another item of Telepermitted  
equipment of a different make or model, nor does it imply  
that any product is compatible with all of Telecom’s network  
services. This device may be subject to ringing or bell tinkle  
when certain other devices are connected to the same line.  
If this occurs, the problem should not be referred to the  
Telecom Faults service.  
Oricom is not liable for any damages caused by the product  
or the failure of the product to perform, including any lost  
profits or savings or special, incidental or consequential  
damages. Oricom is not liable for any claim made by a third  
party or made by you on behalf of a third party.  
This limitation of liability applies whether damages are  
sought, or a claim made, under this Warranty or as a tort  
claim (including negligence and strict product liability), a  
contract claim or any other claim. However, this limitation of  
liability will not apply to claims for personal injury.  
Nothing in this Warranty excludes, restricts or modifies  
any condition, warranty, right or remedy which pursuant to  
the Trade Practices Act 1974 applies to this Warranty and  
which may not be so excluded, restricted or modified. For  
warranties that cannot be excluded, restricted or modified,  
Oricom limits the remedies available to those specified in  
the relevant legislation.  
This equipment shall not be set to make automatic calls to  
the Telecom “111” Emergency Service.  
This equipment may not provide for the effective hand-over  
of a call to another device connected to the same line.  
32 AppENDIx  
REN (RN for New Zealand)  
The REN (Ringer Equivalence Number) or (RN) is of  
significance only if you wish to connect more than 1  
telephone to your telephone line. A standard telephone  
line has a maximum REN capacity of 3 (RN of 5). It is  
possible to connect 3 (5) devices with a REN of 1 (RN  
of 1) with no degradation to the product’s performance.  
Exceeding this limit may cause the volume of the ringer  
in any phone to decrease or not ring at all.  
Caller ID  
Customers using non Telecom toll services should not  
use the dial back feature for local calls as this will incur  
a charge only the 7 digit number should be dialled.  
Some of the CID services listed may not be available in  
New Zealand.  
This telephone is not designed for making emergency  
telephone calls when the power fails. Make alternative  
arrangements for access to emergency services.  
Australia  
Oricom International Pty Ltd  
Locked Bag 658  
South Windsor, NSW 2756  
Customer Support  
Phone: (02) 4574 8888  
Fax: (02) 4574 8898  

Indesit KT6G2W User Manual
JVC AV 21MX56 User Manual
Kenwood Computer Monitor DDX370 User Manual
Matsui America MAT37LW507E User Manual
MicroBoards Technology MX 1 User Manual
NEC Electronics America Computer Monitor MultiSync EA224WMi User Manual
Nortel Networks Nortel Business Series Terminal T7000 User Manual
Panasonic CT 36HL44 User Manual
Philips 22PDL49X6H User Manual
Philips 109E5 User Manual