Nortel Networks Nortel WLAN Handset 2210 User Manual

WLAN IP Handset 2210/2211/2212 User Guide  
BCM  
Business Communications Manager  
Document Status: Standard  
Document Number: NN40050-101  
Document Version: 01.01  
Date: September 2006  
Task list  
3
Task list  
WLAN IP Handset 2210/2211/2212 User Guide  
 
4
Task list  
NN40050-101  
Contents  
5
Contents  
WLAN IP Handset 2210/2211/2212 User Guide  
 
6
Contents  
NN40050-101  
7
Chapter 1  
Getting started  
This document is a global document. Contact your system supplier or your Nortel representative to  
verify that the hardware and software described are supported in your area.  
This section contains information on the following topics:  
About this guide  
This document describes the features and functions of the WLAN IP Handset 2210, 2211, and  
2212 phones.  
Audience  
This guide is intended for installers and users of WLAN IP Handset 2210, 2211, and 2212 phones.,  
as well as for individuals responsible for configuring, maintaining, and troubleshooting the WLAN  
IP Handset 2210, 2211, and 2212 phones.  
WLAN IP Handset 2210/2211/2212 User Guide  
       
8
Chapter 1 Getting started  
Symbols and text conventions  
These symbols are used to highlight critical information for the BCM system:  
Caution: Alerts you to conditions where you can damage the equipment.  
Danger: Alerts you to conditions where you can get an electrical shock.  
Warning: Alerts you to conditions where you can cause the system to fail or work  
improperly.  
Note: Alerts you to important information.  
Tip: Alerts you to additional information that can help you perform a task.  
Security note: Indicates a point of system security where a default should be changed,  
or where the administrator needs to make a decision about the level of security required  
!
for the system.  
Warning: Alerts you to ground yourself with an antistatic grounding  
strap before performing the maintenance procedure.  
Warning: Alerts you to remove the BCM main unit and expansion unit  
power cords from the ac outlet before performing any maintenance  
procedure.  
NN40050-101  
 
Chapter 1 Getting started  
9
These conventions and symbols are used to represent the Business Series Terminal display and  
dialpad.  
Convention  
Example  
Used for  
Word in a special font (shown in  
the top line of the display)  
Command line prompts on display telephones.  
Pswd:  
Underlined word in capital letters  
(shown in the bottom line of a two  
line display telephone)  
Displaybutton option. Available on two line display  
telephones. Press the button directly below the  
option on the display to proceed.  
PLAY  
Dialpad buttons  
Buttons you press on the dialpad to select a  
particular option.  
£
These text conventions are used in this guide to indicate the information described:  
Convention  
Description  
bold Courier  
text  
Indicates command names and options and text that you need to enter.  
Example: Use the infocommand.  
Example: Enter show ip{alerts|routes}.  
italic text  
Indicates book titles  
plain Courier  
text  
Indicates command syntax and system output (for example, prompts  
and system messages).  
Example: Set Trap Monitor Filters  
FEATURE  
HOLD  
RELEASE  
Indicates that you press the button with the coordinating icon on  
whichever set you are using.  
separator ( > )  
Shows menu paths.  
Example: Protocols > IP identifies the IP option on the Protocols  
menu.  
WLAN IP Handset 2210/2211/2212 User Guide  
10 Chapter 1 Getting started  
How to get Help  
This section explains how to get help for Nortel products and services.  
Getting Help from the Nortel Web site  
The best source of support for Nortel products is the Nortel Support Web site:  
This site enables customers to:  
download software and related tools  
download technical documents, release notes, and product bulletins  
sign up for automatic notification of new software and documentation  
search the Support Web site and Nortel Knowledge Base  
open and manage technical support cases  
Getting Help over the phone from a Nortel Solutions Center  
If you have a Nortel support contract and cannot find the information you require on the  
Nortel Support Web site, you can get help over the phone from a Nortel Solutions Center.  
In North America, call 1-800-4NORTEL (1-800-466-7865).  
Outside North America, go to the Web site below and look up the phone number that applies  
in your region:  
When you speak to the phone agent, you can reference an Express Routing Code (ERC) to more  
quickly route your call to the appropriate support specialist. To locate the ERC for your product or  
service, go to:  
Getting Help through a Nortel distributor or reseller  
If you purchased a service contract for your Nortel product from a distributor or authorized  
reseller, you can contact the technical support staff for that distributor or reseller.  
NN40050-101  
       
11  
Chapter 2  
WLAN Handsets overview  
The Nortel WLAN Handset 2210, WLAN Handset 2211, and the WLAN Handset 2212 for BCM  
are fully functional wireless handsets specifically designed for the busy office environment.  
In this user guide, the WLAN Handset 2210, WLAN Handset 2211, and WLAN Handset 2212 are  
referred to generically as WLAN Handset.  
IMPORTANT!  
User must end every call  
The user must end every call, by pressing the Power Off/End Call key, to  
release system resources and allow the WLAN Handset to function properly.  
If this is not done, it will result in the ringer not ringing and you might miss an  
important call.  
IMPORTANT!  
The WLAN Handset must be fully charged before initial use. See “Battery  
Warning:  
Follow standard acceptance procedures before operating  
the WLAN Handset near life-support systems.  
To minimize risk of interference, pacemaker users should not  
carry the WLAN Handset next to the pacemaker.  
Avoid placing the WLAN Handset near small metallic  
objects. The WLAN Handset earpiece attracts magnetic  
objects.  
The WLAN Handset produces noise noticeable to hearing  
aid users. Use a headset compatible with hearing aids.  
This device complies with part 15 of the FCC Rules.  
Operation is subject to the following two conditions: (1) This  
device may not cause harmful interference, and (2) this  
device must accept any interference received, including  
interference that may cause undesired operation.  
CAUTION  
Loud noise environment: The WLAN Handset has been  
designed to produce optimal voice quality. However, when  
used in extremely loud noise environments (for example,  
close to working heavy machinery), users may experience  
degradation in call quality performance due to echo. Avoid  
using the WLAN Handset when traversing these types of  
environments.  
WLAN IP Handset 2210/2211/2212 User Guide  
   
12 Chapter 2 WLAN Handsets overview  
This guide contains information about:  
The following figure shows the WLAN Handset 2210, WLAN Handset 2211, and  
WLAN Handset 2212.  
Note: The WLAN Handset 2210 and WLAN Handset 2211 are shown in the  
desktop charger. There is no desktop charger for the WLAN Handset 2212.  
Figure 1 WLAN Handset 2210, WLAN Handset 2211, and WLAN Handset 2212  
WLAN Handset 2211  
WLAN Handset 2210  
WLAN Handset 2212  
WLAN Handset buttons and keys  
Figure 2 on page 13 shows the WLAN Handset 2210, WLAN Handset 2211, and  
WLAN Handset 2212 buttons and keys.  
NN40050-101  
 
Chapter 2 WLAN Handsets overview 13  
Figure 2 WLAN Handset 2210, WLAN Handset 2211, and WLAN Handset 2212 buttons and keys  
G
C
G
C
G
H
C
D
D
B
A
D
B
A
I
A
I
B
J
I
J
J
E
F
E
F
E
F
WLAN Handset 2210  
WLAN Handset 2211  
WLAN Handset 2212  
The following table describes the WLAN Handset buttons and keys.  
Table 1 WLAN Handset buttons, keys, and descriptions (Sheet 1 of 2)  
Button/key  
Description  
Power On/Start Call key  
A
B
Turns on the handset. This key also affects some of the states of the  
Power Off/End Call key  
Ends an active call and turns off the handset.  
The user must end every call to release system resources and allow the  
handset to function properly.  
Feature and Display soft keys  
Ftre  
C
The first of the four soft keys is the Feature soft key, which starts or ends  
a feature. The next three soft keys are Display keys, which show feature  
options.  
Menu key  
D
E
Displays the full description of the Display soft keys abbreviations and  
accesses the handset features.  
Function key  
Accesses handset functions when in active (idle) state.  
The Function key also provides access to the User Option menu in the  
standby state.  
Line key  
F
Accesses the Feature menu. For more information on Feature menu.  
WLAN IP Handset 2210/2211/2212 User Guide  
 
14 Chapter 2 WLAN Handsets overview  
Table 1 WLAN Handset buttons, keys, and descriptions (Sheet 2 of 2)  
Button/key  
Description  
Up, Down, and Select buttons  
G
H
Enables you to navigate and activate the various menu options.  
Adjusts the speaker and ringer volume.  
Push-to-Talk button  
Push-to-Talk is available on the WLAN Handset 2211 only.  
Activates the Push-to-Talk feature on the WLAN Handset 2211.  
Left arrow and Star button  
I
Enables scrolling to the left for menu navigation.  
Right arrow and Pound button  
J
Enables scrolling to the right for menu navigation.  
Scrolling  
Scrolling up, down, left and right are performed as shown in Table 1.  
Table 1 Scrolling functions  
To scroll:  
Use:  
Up  
Volume Up button  
Down  
Left  
Volume Down button  
Right  
WLAN Handset display  
There are three areas to the WLAN Handset display:  
Status area  
Information area  
Feature options area  
NN40050-101  
     
Chapter 2 WLAN Handsets overview 15  
The following figure shows an example of the WLAN Handset display.  
Figure 3 WLAN Handset display  
Status area  
Information area  
Feature options area  
Status area  
The status area displays the handset status. It can include:  
status indicators (see the table below)  
left and right arrows  
a series of dots representing the line keys, which change to a number when active  
The following table describes the status indicators on your WLAN Handset.  
WLAN IP Handset 2210/2211/2212 User Guide  
 
16 Chapter 2 WLAN Handsets overview  
Table 2 Status indicators  
J I H G F These symbols give a visual indication (from strong to weak) of the signal  
strength to the handset.  
No Service  
You are outside the coverage area and cannot receive or place calls. The  
out-of-service tone plays. Return to the coverage area to re-establish the  
connection.  
Note: The No Service status indicator displays in the information area of the  
handset display.  
D C B  
A
These symbols give a visual indication of the Battery charge. The D  
indicates that the battery is fully charged while the B indicates that the  
charge is low.  
Your battery pack charge is very low. An audible beep also sounds. Replace  
your battery pack within two minutes.  
E
K
You have a new voicemail message.  
Your handset is downloading a new firmware file. You will be unable to  
make or receive calls until the download is complete.  
Do not power off the handset until the download icon disappears.  
Melody  
A melody is played when the WLAN Handset is turned on for the first time  
following a completed charge.  
In Service Tone  
Line Indicator  
When the handset completes registration with the Call Server, it plays the  
in-service tone.  
The Line Indicator area displays the line currently in use. Any lines which  
are not idle or active (for example, if the line is on hold or forwarded) will  
have a plus sign (+) sign in front of the entry for that line.  
Right/Up and Left/ These icons, on either side of the Line Indicator, are used in the in-call  
Down Arrows  
menus to indicate “more items below or left” and “more items above or  
right”.  
Information area  
The Information area shows:  
the extension number of the handset  
a line for general information  
features and call information when the handset is in use  
NN40050-101  
 
Chapter 2 WLAN Handsets overview 17  
Feature options area  
When a feature is activated, or when you are on an active call, the Feature options area shows you  
the action you must take to proceed.  
For example: Pswd. This means you must enter your mailbox password.  
The Feature options area shows the label for the Ftre soft key and for the three display soft keys.  
These button labels appear directly above the Feature and display soft keys, and to the right of the  
Ftre label on the display. These button labels vary, depending on the feature in use.  
WLAN handset states  
The WLAN Handset can be in one of the states described in the following table.  
IMPORTANT!  
User MUST end every call  
The user must end every call, by pressing the Power Off/End Call key, to  
release system resources and allow the WLAN Handset to function properly.  
If this is not done, it will result in the ringer not ringing and you might miss an  
important call.  
Table 3 States of the WLAN Handset  
State  
Description  
Power off  
The handset is turned off. It is not registered with the Call Server.  
Normally the handset enters the power-off state when the user presses Power Off/  
End Call for approximately two seconds when the handset is in the standby state.  
The batteries can be recharged in the power-off state.  
Standby  
This is the normal state when the handset is online but inactive. In the standby state, the  
handset can receive calls and access the User Option menu.  
To perform other operations, the handset must be active (off-hook).  
The standby state uses less power than the active (idle) state. The batteries can be  
recharged in the standby state.  
When the handset is in the standby state, the programmed extension number is shown in  
the display area.  
Active  
This is equivalent to a regular telephone being off-hook.  
(off-hook)  
The handset goes to the active (off-hook) state by pressing Power On/Start Call when  
the handset is in the standby or active (idle) states. When in this state, the handset uses a  
soft ring.  
Active (idle)  
This is equivalent to a regular telephone being idle. The active (idle) state is reached in  
two ways:  
An incoming call in the Standby state causes the handset to go to the active (idle) state  
and begin ringing.  
The user presses FCN and 3 when the handset is in the active (off-hook) state to access  
the function menu. In this state, the handset does not ring when a call comes in.  
In the active (idle) state, the handset and access point exchange a small packet  
approximately once every 15 milliseconds. This increases the power consumption and  
consumes bandwidth, particularly for the RF portion of the link. Therefore, the handset is  
not normally left in the active (idle) state except for special situations.  
WLAN IP Handset 2210/2211/2212 User Guide  
               
18 Chapter 2 WLAN Handsets overview  
Table 3 States of the WLAN Handset  
State  
Description  
Active (on-hook) This state is entered when the handset is in standby state and the user presses the Menu  
key. The handset appears to be on-hook from the Call Server point of view, and loud  
ringing will occur (when required). The handset display is active and the Menu, FCN and  
Line menus can be accessed. The user returns to the standby state by pressing the  
Power Off/End Call key. If no keys are pressed for a period of 10 seconds, the state times  
out and the handset returns to the standby state. Pressing the Power Off/End Call key in  
any of the menus will exit the menu. Pressing the Power Off/End Call key again will  
return the handset to standby state.  
If the user selects any menu item or presses a soft key, the handset changes into the  
active (off-hook) state, the timeout condition is removed and the handset will use a soft  
ring.  
Error  
The handset enters the error state when it loses the signal from the access point.  
If the handset regains the signal within approximately 20 seconds, it returns to the state it  
just left. If the handset is out of range for longer than 20 seconds, the handset restarts and  
returns to the standby state.  
For more information on error messages, see “Display messages” on page 44.  
Active call  
The handset enters the active call state when a user is in an active conversation. To enter  
this state, the user either makes a call or answers an incoming call. While in this state, the  
handset will use a soft ring to alert the user to another call. The user leaves this state  
when the call is completed by pressing the Power Off/End Call key or if an incoming call  
is ended before the user answers it.  
Push-to-Talk  
The push-to-talk state begins with the first push-to-talk transmission and ends when there  
has been no two-way radio traffic on the channel for 10 seconds.  
(WLAN Handset  
2211 only)  
While in the push-to-talk state, it is not possible to use the keypad for any other functions.  
However, it is possible to place and receive telephone calls.  
Setting up the WLAN Handset  
This section describes the following initial setup options for your WLAN Handset:  
NN40050-101  
         
Chapter 2 WLAN Handsets overview 19  
To select the Keypad Autolock  
1
2
3
4
5
6
Press  
when the handset is in the standby state.  
Press the Up and Down buttons to scroll through the menu and highlight Phone Options.  
Press the Select button (or OK) to select Phone Options.  
Press the Up and Down buttons to scroll through the menu and highlight Keypad Autolock.  
Press the Select button (or OK) to select Keypad Autolock.  
Press the Up and Down buttons to scroll through the menu and highlight one of the following  
settings:  
No Delay (default).  
5 seconds — key pad locks after five seconds.  
10 seconds — key pad locks after 10 seconds  
20 seconds — key pad locks after 20 seconds.  
7
8
Press the Select button (or OK) to select the highlighted setting.  
Do one of the following:  
Press UP to return to the previous menu and configure another option.  
Press to exit all menus and return to the standby state.  
You can also press Exit from the top-level menu to exit the menu and return to the active  
(off-hook) state.  
See “Lock and unlock the keypad” on page 28 for further information.  
Select the Language  
If the Call Server supports multiple languages, the language option will list the available  
languages. The user option menu and all other local handset prompts are English-only. Menus and  
screens that originate from the Call Server are displayed in the configured language.  
To select a language  
1
2
3
4
5
Press  
when the handset is in the standby state.  
Press the Up and Down buttons to scroll through the menu and highlight Language.  
Press the Select button (or OK) to select Language.  
Press the Up and Down buttons to scroll through the list of languages.  
Press the Select button (or OK) to select the highlighted language.  
WLAN IP Handset 2210/2211/2212 User Guide  
     
20 Chapter 2 WLAN Handsets overview  
6
Do one of the following:  
Press UP to return to the previous menu and configure another option.  
Press to exit all menus and return to the standby state.  
You can also press Exit from the top-level menu to exit the menu and return to the active  
(off-hook) state.  
Ring Options  
The Ring Options enables you to configure the WLAN Handset ring tone for the three different  
ringer types: Telephone Ring, Auxiliary 1, and Auxiliary 2.  
Note: Auxiliary 1 and Auxiliary 2 are reserved for future use.  
Telephone Ring allows further configuration for:  
Ring Cadence — controls the ringing rhythm.  
Ring Tone — controls the ringing tone (see note 1).  
Ring Volume — controls the ringing volume.  
Vibrate Cadence — controls the vibration rhythm.  
Ring Delay — controls how long the vibrate cadence plays before the audible ring starts (see  
note 2).  
Note: Ring Tone is not displayed in the menu when Ring Cadence is turned off.  
Note: Ring Delay is not displayed in the menu when Ring Cadence or Vibrate  
Cadence is turned off.  
To select the Ring Cadence  
1
2
3
4
5
6
7
Press  
when the handset is in the standby state.  
Press the Up and Down buttons to scroll through the menu and highlight Ring Options.  
Press the Select button (or OK) to select Ring Options.  
Press the Up and Down buttons to scroll through the menu and highlight Telephone Ring.  
Press the Select button (or OK) to select Telephone Ring.  
Press the Up and Down buttons to scroll through the menu and highlight Ring Cadence.  
Press the Select button (or OK) to select Ring Cadence.  
NN40050-101  
   
Chapter 2 WLAN Handsets overview 21  
8
9
Scroll to one of the desired options:  
Off — ringer is turned off.  
PBX — ringing uses the distinctive ringing pattern sent to the handset from the call server.  
Continuous — ringing is continuous.  
Short Pulse — ringing occurs in short bursts.  
Long Pulse — ringing occurs in long bursts.  
Press the Select button (or OK) to select the highlighted option.  
10 Do one of the following:  
Press UP to return to the previous menu and configure another option.  
Press to exit all menus and return to the standby state.  
You can also press Exit from the top-level menu to exit the menu and return to the active  
(off-hook) state.  
To select the Ring Tone  
Note: Ring Tone is not displayed in the menu when Ring Cadence is turned off.  
1
2
3
4
5
6
7
8
Press  
when the handset is in the standby state.  
Press the Up and Down buttons to scroll through the menu and highlight Ring Options.  
Press the Select button (or OK) to select Ring Options.  
Press the Up and Down buttons to scroll through the menu and highlight Telephone Ring.  
Press the Select button (or OK) to select Telephone Ring.  
Press the Up and Down buttons to scroll through the menu and highlight Ring Tone.  
Press the Select button (or OK) to select Ring Tone.  
Scroll to one of the desired options:  
Tone 1  
Tone 2  
Tone 3  
Tone 4  
Tone 5  
9
Press the Play soft key to preview the tone.  
WLAN IP Handset 2210/2211/2212 User Guide  
 
22 Chapter 2 WLAN Handsets overview  
10 Press the Select button (or OK) to select the highlighted option.  
11 Do one of the following:  
Press UP to return to the previous menu and configure another option.  
Press to exit all menus and return to the standby state.  
You can also press Exit from the top-level menu to exit the menu and return to the active  
(off-hook) state.  
To select the Ring Volume  
1
2
3
4
5
6
7
8
9
Press  
when the handset is in the standby state.  
Press the Up and Down buttons to scroll through the menu and highlight Ring Options.  
Press the Select button (or OK) to select Ring Options.  
Press the Up and Down buttons to scroll through the menu and highlight Telephone Ring.  
Press the Select button (or OK) to select Telephone Ring.  
Press the Up and Down buttons to scroll through the menu and highlight Ring Volume.  
Press the Select button (or OK) to select Ring Volume.  
Press the Up and Down buttons to increase or decrease the volume.  
Press the Select button (or OK) to save the volume.  
10 Do one of the following:  
Press UP to return to the previous menu and configure another option.  
Press to exit all menus and return to the standby state.  
You can also press Exit from the top-level menu to exit the menu and return to the active  
(off-hook) state.  
Note: You cannot change the ring volume on WLAN Handset 2210 or WLAN  
Handset 2212. The WLAN Handset 2210 and WLAN Handset 2212 do not  
support the Ring Volume feature. You can change the ring volume on WLAN  
Handset 2211, where the Ring Volume feature is supported.  
To select the Vibrate Cadence  
1
2
3
4
5
6
7
Press  
when the handset is in the standby state.  
Press the Up and Down buttons to scroll through the menu and highlight Ring Options.  
Press the Select button (or OK) to select Ring Options.  
Press the Up and Down buttons to scroll through the menu and highlight Telephone Ring.  
Press the Select button (or OK) to select Telephone Ring.  
Press the Up and Down buttons to scroll through the menu and highlight Vibrate Cadence.  
Press the Select button (or OK) to select Vibrate Cadence.  
NN40050-101  
   
Chapter 2 WLAN Handsets overview 23  
8
9
Scroll to one of the desired options:  
Off — vibration is turned off.  
PBX — vibration uses the distinctive pattern sent to the handset from the call server.  
Continuous — vibration is continuous.  
Short Pulse — vibration occurs in short bursts.  
Long Pulse — vibration occurs in long bursts.  
Press the Select button (or OK) to select the highlighted option.  
10 Do one of the following:  
Press UP to return to the previous menu and configure another option.  
Press to exit all menus and return to the standby state.  
You can also press Exit from the top-level menu to exit the menu and return to the active  
(off-hook) state.  
To select the Ring Delay  
Note: Ring Delay is not displayed in the menu when Ring Cadence or Vibrate  
Cadence is turned off.  
1
2
3
4
5
6
7
8
Press  
when the handset is in the standby state.  
Press the Up and Down buttons to scroll through the menu and highlight Ring Options.  
Press the Select button (or OK) to select Ring Options.  
Press the Up and Down buttons to scroll through the menu and highlight Telephone Ring.  
Press the Select button (or OK) to select Telephone Ring.  
Press the Up and Down buttons to scroll through the menu and highlight Ring Delay.  
Press the Select button (or OK) to select Ring Delay.  
Scroll to one of the desired options:  
No Delay — the handset rings and vibrates immediately.  
5 Second Delay — the handset vibrates for five seconds before ringing starts.  
10 Second Delay —the handst vibrates for 10 seconds before ringing starts.  
9
Press the Select button (or OK) to select the highlighted option.  
10 Do one of the following:  
Press UP to return to the previous menu and configure another option.  
Press to exit all menus and return to the standby state.  
You can also press Exit from the top-level menu to exit the menu and return to the active  
(off-hook) state.  
WLAN IP Handset 2210/2211/2212 User Guide  
 
24 Chapter 2 WLAN Handsets overview  
Phone Options  
The Phone Options menu enables you to configure:  
Noise Mode — enables you to adjust the WLAN Handset for different levels of noise within the  
working environment.  
Key Tones — determines if tones play when the keys are pressed.  
Warning Tones — determines if warning tones — such as system up, system down or out of  
range — are played.  
Display Contrast — controls the amount of contrast for the display for different lighting  
conditions.  
Keypad Autolock — controls the automatic locking of the handset key pad when the handset is  
in standby mode.  
To select the Noise Mode  
1
2
3
4
5
6
Press  
when the handset is in the standby state.  
Press the Up and Down buttons to scroll through the menu and highlight Phone Options.  
Press the Select button (or OK) to select Phone Options.  
Press the Up and Down buttons to scroll through the menu and highlight Noise Mode.  
Press the Select button (or OK) to select Noise Mode.  
Press the Up and Down buttons to scroll through the menu and highlight one of the following  
settings:  
Normal — For most office environments (default).  
High — For moderate background noise.  
Severe — For extremely noisy conditions.  
7
8
Press the Select button (or OK) to select the highlighted setting.  
Do one of the following:  
Press UP to return to the previous menu and configure another option.  
Press to exit all menus and return to the standby state.  
You can also press Exit from the top-level menu to exit the menu and return to the active  
(off-hook) state.  
To select the Key Tones  
1
2
3
4
5
Press  
when the handset is in the standby state.  
Press the Up and Down buttons to scroll through the menu and highlight Phone Options.  
Press the Select button (or OK) to select Phone Options.  
Press the Up and Down buttons to scroll through the menu and highlight Key Tones.  
Press the Select button (or OK) to select Key Tones.  
NN40050-101  
       
Chapter 2 WLAN Handsets overview 25  
6
Press the Up and Down buttons to scroll through the menu and highlight one of the following  
settings:  
Enable Tones (default)  
Disable Tones  
7
8
Press the Select button (or OK) to select the highlighted setting.  
Do one of the following:  
Press UP to return to the previous menu and configure another option.  
Press to exit all menus and return to the standby state.  
You can also press Exit from the top-level menu to exit the menu and return to the active  
(off-hook) state.  
To select the Warning Tones  
1
2
3
4
5
6
Press  
when the handset is in the standby state.  
Press the Up and Down buttons to scroll through the menu and highlight Phone Options.  
Press the Select button (or OK) to select Phone Options.  
Press the Up and Down buttons to scroll through the menu and highlight Warning Tones.  
Press the Select button (or OK) to select Warning Tones.  
Press the Up and Down buttons to scroll through the menu and highlight one of the following  
settings:  
Enable Warnings (default)  
Disable Warnings  
7
8
Press the Select button (or OK) to select the highlighted setting.  
Do one of the following:  
Press UP to return to the previous menu and configure another option.  
Press to exit all menus and return to the standby state.  
You can also press Exit from the top-level menu to exit the menu and return to the active  
(off-hook) state.  
To select the Display Contrast  
1
2
3
4
5
6
Press  
when the handset is in the standby state.  
Press the Up and Down buttons to scroll through the menu and highlight Phone Options.  
Press the Select button (or OK) to select Phone Options.  
Press the Up and Down buttons to scroll through the menu and highlight Display Contrast.  
Press the Select button (or OK) to select Display Contrast.  
Press the Up and Down buttons to increase or decrease the contrast.  
WLAN IP Handset 2210/2211/2212 User Guide  
   
26 Chapter 2 WLAN Handsets overview  
7
8
Press the Select button (or OK) to select the highlighted setting.  
Do one of the following:  
Press UP to return to the previous menu and configure another option.  
Press to exit all menus and return to the standby state.  
You can also press Exit from the top-level menu to exit the menu and return to the active  
(off-hook) state.  
Configure push-to-talk  
Push-to-talk is available on the WLAN Handset 2211 only.  
Push-to-talk mode enables two-way radio communication with another WLAN Handset 2211  
user. You can enable/disable Push-to-Talk mode and select a channel.  
To configure Push-to-Talk for the handset  
1
2
3
4
5
6
Press  
when the handset is in the standby state.  
Press the Up and Down buttons to scroll through the menu and highlight Push-to-Talk.  
Press the Select button (or OK) to select Push-to-Talk.  
Press the Up and Down buttons to scroll through the menu and highlight Enable/Disable.  
Press the Select button (or OK) to select Enable/Disable.  
Press the Up and Down buttons to scroll through the menu and highlight one of the following  
settings:  
PTT Enable — Enables Push-to-Talk mode.  
PTT Disable — Disables Push-to-Talk mode. This is the default.  
7
8
9
Press the Select button (or OK) to select the highlighted option.  
Press the Up soft key to return to the previous menu.  
Press the Up and Down buttons to scroll through the menu and highlight Channel.  
10 Use the Up and Down buttons to scroll through the menu and highlight a channel (1 to 8).  
11 Press the Select button (or OK) to select the channel.  
12 Do one of the following:  
Press UP to return to the previous menu and configure another option.  
Press to exit all menus and return to the standby state.  
You can also press Exit from the top-level menu to exit the menu and return to the active  
(off-hook) state.  
NN40050-101  
       
Chapter 2 WLAN Handsets overview 27  
Adjust ringer volume  
You have two ways to adjust the ringer volume:  
Press the Up or Down button while the handset is ringing.  
configure the volume using the FCN button when in standby state. See “To select the Ring  
Volume” on page 22 for further information.  
Adjust speaker volume  
You can increase or decrease the speaker volume of the WLAN Handset 2211 only.  
You have two ways to adjust the ringer volume:  
Press the Up or Down button while on a call.  
Configure the volume using the FCN button when in standby state.  
To adjust speaker volume using the Function menu  
1
2
3
4
5
6
7
8
Press  
when the handset is in the standby state.  
Press the Up and Down buttons to scroll through the menu and highlight Push-to-Talk.  
Press the Select button (or OK) to select Push-to-Talk.  
Press the Up and Down buttons to scroll through the menu and highlight Audio Volume.  
Press the Select button (or OK) to select Audio Volume.  
Press the Up and Down buttons to adjust the volume to a suitable level.  
Press the Select button (or OK) to select the setting.  
Do one of the following:  
Press UP to return to the previous menu and configure another option.  
Press to exit all menus and return to the standby state.  
You can also press Exit from the top-level menu to exit the menu and return to the active  
(off-hook) state.  
Silence the ringer  
You can silence (or mute) the WLAN Handset ringer.  
You silence the ringer in one of two ways:  
To silence the ringer, press  
while the handset is ringing.  
Use the FCN menu in standby mode  
WLAN IP Handset 2210/2211/2212 User Guide  
       
28 Chapter 2 WLAN Handsets overview  
To silence the ringer using the Function menu  
1
2
3
4
5
6
7
8
9
Press  
when the handset is in the standby state.  
Press the Up and Down buttons to scroll through the menu and highlight Ring Options.  
Press the Select button (or OK) to select Ring Options.  
Press the Up and Down buttons to scroll through the menu and highlight Telephone Ring.  
Press the Select button (or OK) to select Telephone Ring.  
Press the Up and Down buttons to scroll through the menu and highlight Ring Cadence.  
Press the Select button (or OK) to select Ring Cadence.  
Press the Up and Down buttons to scroll through the menu and highlight Off.  
Press the Select button (or OK) to select Off.  
10 Press the Select button (or OK) to select the setting.  
11 Do one of the following:  
Press UP to return to the previous menu and configure another option.  
Press to exit all menus and return to the standby state.  
You can also press Exit from the top-level menu to exit the menu and return to the active  
(off-hook) state.  
Lock and unlock the keypad  
When the automatic keypad locking is enabled, the keypad will lock after the configured number  
of seconds with no key presses (see “To select the Keypad Autolock” on page 19). You can also  
lock the keypad before the delay, using “To lock the keypad” on page 28.  
To unlock the locked keypad, follow “To unlock the keypad” on page 28.  
To lock the keypad  
1
2
3
Press  
when the handset is in the standby state.  
Press the Up and Down buttons to scroll through the menu and highlight Lock Keys.  
Press the Select button (or OK) to select Lock Keys.  
The keypad is locked immediately.  
To unlock the keypad  
1
2
Press  
when the handset is in the standby state.  
key.  
Press the  
The keypad is unlocked immediately.  
NN40050-101  
       
Chapter 2 WLAN Handsets overview 29  
Security  
The WLAN Handsets provide two security modes:  
insecure — This is the default mode.  
secure  
Your handset is pre-programmed by the system administrator for the type of security you need.  
For more information, consult your administrator.  
Warning: Do not change the security level through your handset.  
WLAN IP Handset 2210/2211/2212 User Guide  
 
30 Chapter 2 WLAN Handsets overview  
NN40050-101  
31  
Chapter 3  
Feature and function menus  
You can view the features and functions programmed in your system using various menus, soft  
key features, and the Line (DN) features. You can access some functions and features using one or  
more of the methods described in this section.  
This section describes theWLAN Handset feature and function menus:  
Note: For more information about the features available to yourWLAN Handset  
and how to use them, refer to the BCM Telephone Feature Card.  
Feature and function keys  
The following table lists the features and functions available on the WLAN Handset, along with  
their key sequence.  
Table 4 WLAN Handset feature and function keys  
Key sequence  
Feature/Function  
+ 1  
+ 2  
+ 3  
+ 4  
+ 5  
+ 6  
+ 7  
+ 8  
Mute  
Hold  
Goodbye  
Directory  
Inbox  
Outbox  
Quit  
Copy  
+ 1  
+ 2  
+ 3  
+ 4  
+ 5  
+ 6  
Intercom  
Intercom  
Page - General  
Last Number Redial  
Conference Call  
Call Forward  
WLAN IP Handset 2210/2211/2212 User Guide  
       
32 Chapter 3 Feature and function menus  
Soft Key Abbreviations menu–MENU key  
Use the Soft Key Abbreviations menu to view the full description of the soft key abbreviations and  
access the WLAN Handset features.  
To activate a feature  
1
2
3
Place the handset in the active (idle) or active (off-hook) state.  
Press to view the Soft Key Abbreviations menu.  
Press the Up and Down buttons to scroll through the list of features. The full description is  
highlighted in the display area.  
4
Do one of the following:  
Press the Select button (or OK) to activate the highlighted feature.  
Press the appropriate number key. The feature does not have to be highlighted.  
Function menu—FCN key  
Use the Function menu to view and activate the WLAN Handset functions.  
To activate a function  
1
2
Place the handset in the active (idle) or active (off-hook) state.  
Press  
to display the first four functions in the display area. Press  
again to view more  
functions.  
3
4
Press the Up and Down buttons to scroll through the list of functions. The abbreviation is  
highlighted in the display area.  
Do one of the following:  
Press the Select button (or OK) to activate the highlighted feature.  
Press the appropriate number key. The feature does not have to be highlighted.  
Feature menu—LINE key  
Use the Feature menu to view and activate the WLAN Handset line features. These features are  
programmed on each handset using the six line keys (number keys 1 through 6).  
Note: A feature must be available on the system before it can be programmed on  
a handset.  
NN40050-101  
           
Chapter 3 Feature and function menus 33  
To activate a feature  
1
2
Place the handset in the active (idle) or active (off-hook) state.  
Press  
to view the first screen of the Feature menu. Press  
again to view the second  
screen.  
3
4
Press the Up and Down buttons to scroll through the list of features. The abbreviation is  
highlighted in the display area.  
Do one of the following:  
Press the Select button (or OK) to activate the highlighted feature.  
Press the number key (1 through 6) corresponding to the desired feature. The feature does  
not have to be highlighted.  
Program Feature menu items  
You must be in the active (off-hook) state to program a Feature menu item.  
To use external autodial  
1
2
3
4
Press Feature *1.  
Press  
and a number key (1 through 6) corresponding to an available key.  
Dial the external number, including routing codes.  
Press OK to store the number.  
To use internal autodial  
1
2
3
4
Press Feature *2.  
Press  
and a number key (1 through 6) corresponding to an available key.  
Dial the extension number.  
Press OK to store the number.  
To use features  
1
2
3
4
Press Feature *3.  
Press  
and a number key (1 through 6) corresponding to an available key.  
Press Feature and enter the feature code.  
Press OK to store the feature code.  
WLAN IP Handset 2210/2211/2212 User Guide  
         
34 Chapter 3 Feature and function menus  
To erase memory buttons  
1
2
3
Press Feature *1.  
Press  
and a number key (1 through 6) corresponding to an available key.  
Press OK to erase the button.  
NN40050-101  
 
35  
Chapter 4  
Features, functions, and buttons  
This section describes some of the WLAN Handset buttons and call features:  
Note: For more information about the features available to your WLAN Handset  
and how to use them, refer to the BCM Telephone Feature Card.  
IMPORTANT!  
User MUST end every call  
The user must end every call, by pressing the Power Off/End Call key, to  
release system resources and allow the WLAN Handset to function properly.  
If this is not done, it will result in the ringer not ringing and you might miss an  
important call.  
Basic call features  
You can make external and internal calls using the following features:  
Make a call  
Answer a call  
Hold a call  
Use the headset  
Mute a call  
Make a call  
There are many ways to make a call, depending on your handset programming and the type of call.  
To make external calls using line keys  
1
2
3
4
Press  
Press  
to go off-hook.  
to access the Feature menu.  
Press a number key (1 through 6) corresponding to the desired line key.  
Dial the external number.  
WLAN IP Handset 2210/2211/2212 User Guide  
           
36 Chapter 4 Features, functions, and buttons  
To make external calls using intercom keys  
1
2
3
Press  
Press  
to go off-hook.  
to access the Feature menu.  
Press a number key (1 through 6) corresponding to the desired intercom key and enter a line  
pool access code or destination code.  
4
When you hear an external dial tone, dial the external number.  
Note: Contact your system administrator for a list of line pool codes. PRI lines do  
not support line pool access codes; they must be configured as a destination code.  
When entering a destination code on PRI lines, you will not hear dial tone.  
To make internal calls using intercom buttons  
1
2
3
4
Press  
Press  
to go off-hook.  
to access the Feature menu.  
Press a number key (1 through 6) corresponding to the desired intercom key.  
Dial the extension number.  
Note: Contact your system administrator for a list of extension numbers.  
Answer calls  
When your handset rings or vibrates, a line number on the display flashes, and the display shows  
information about the call, such as the caller’s name and extension:  
Press  
.
Hold  
While on a call, press  
and  
.The indicator for the line on hold flashes.  
To retrieve a held call, press  
, while in the active (off-hook) state. Then press the number  
key corresponding to the flashing line number.  
Headset  
You must have a headset installed on your handset to use this feature.  
Connect the headset to the headset jack. Follow the steps in “Make a call” on page 35 to make  
your call.  
To answer a call with a headset plugged into your handset, press any key other than Power  
On/Start Call, Power Off/End Call, the soft keys, or the Up/Down/Select buttons.  
NN40050-101  
         
Chapter 4 Features, functions, and buttons 37  
Mute  
While on a call, press  
Press and  
and  
to turn the microphone off.  
again to turn the microphone on.  
End calls  
You must end every call, by pressing the Power Off/End Call key, to release system resources  
and allow the WLAN Handset to function properly. If you press the Power Off/End Call key, you  
enable the handset to go to low-power standby mode to conserve battery power.  
Push-to-Talk  
Push-to-Talk is available on the WLAN Handset 2211 only.  
Push-to-Talk mode enables the WLAN Handset 2211 to operate in a group broadcast mode in  
addition to the standard handset operation. The WLAN Handset 2211 supports eight multicast  
channels with the current channel saved in the handset memory.  
IMPORTANT!  
Pressing any other keys or buttons (such as the Up/Down/Select or keypad  
keys) while in a Push-to-Talk call will terminate the call.  
Call period  
Push-to-Talk mode operates on the concept of a call period. The Push-to-Talk call period begins  
with the first transmission and ends when there has been no two-way radio traffic on the channel  
for 10 seconds.  
The Push-to-Talk mode controls the handset keypad during the call period. Therefore, it is not  
possible to use the keypad for any other functions. However, it is possible to place and receive  
telephone calls.  
WLAN IP Handset 2210/2211/2212 User Guide  
         
38 Chapter 4 Features, functions, and buttons  
To initiate a Push-to-Talk call  
1
Press the Push-to-Talk button on the right side of the handset.  
The “start transmit” tone sounds within two seconds. The channel is active and the display  
screen shows the current active channel.  
2
3
Speak into the handset’s microphone.  
All WLAN Handsets 2211 that are monitoring that channel hear the transmission.  
Release the Push-to-Talk button.  
The “end transmit” tone sounds. The handset enters the waiting state, where it monitors the  
channel for up to 10 seconds.  
Receive a Push-to-Talk transmission  
Upon receiving a Push-to-Talk transmission, the “receiving alert” tone sounds and the handset  
enters the receive state.  
In this state, the handset receives all conversations on the selected channel. The display shows the  
current active channel, the caller ID of the current transmitter, and an indication that the handset is  
receiving a broadcast transmission.  
At the end of a transmission, the handset enters the waiting state, where it monitors the channel for  
up to 10 seconds and displays “Waiting” on the screen. If no other transmission occurs within 10  
seconds, the “end call” tone sounds and the handset becomes idle.  
To respond to a Push-to-Talk call  
1
When you hear a transmission, press the Push-to-Talk button on the right side of the handset.  
The “start transmit” tone sounds. Since all handsets on that channel are already in the receive  
state, there is no two-second delay.  
2
Speak into the handset’s microphone.  
If no transmission occurs during the 10-second countdown period, the “end call” tone sounds  
and the handset becomes idle.  
To change the Push-to-Talk volume  
1
Use the Up and Down buttons to increase or decrease volume.  
A separate volume is maintained in Push-to-Talk mode.  
NN40050-101  
       
Chapter 4 Features, functions, and buttons 39  
To mute a current Push-to-Talk call  
Mute affects only the current call. When the next call period starts, the audio is automatically  
unmuted. Mute does not allow the user to use the handset’s keypad for anything else.  
1
2
Press the Mute soft key.  
The following prompt displays:  
Mute Two-Way Radio?  
Press the Yes soft key to mute the call.  
The prompt disappears after three seconds if there is no response.  
To unmute a Push-to-Talk call  
1
Press the Unmute soft key.  
The following prompt displays:  
Unmute Two-Way Radio?  
2
Press the Yes soft key to unmute the call.  
The prompt disappears after three seconds if there is no response.  
To end a Push-to-Talk call  
Only the current call is terminated for this handset. When the next call period starts, the handset is  
again in the receive state. You can rejoin a still-active session by initiating a Push-to-Talk call.  
1
Press the Terminate soft key.  
The following prompt displays:  
Terminate Two-Way Radio?  
2
Press the Yes soft key to end the call.  
Push-to-Talk audio is immediately stopped and the handset returns to regular mode.  
To answer a call during a Push-to-Talk call  
An incoming call can be answered while in a Push-to-Talk call. To announce an incoming call, the  
handset rings with a low-volume ring and displays a system message.  
1
2
Press  
.
The Push-to-Talk session is pre-empted.  
After the call is over, press  
as usual to go back on-hook.  
The Push-to-Talk session goes out of pre-empted mode and becomes active again. If an active  
Push-to-Talk call has not ended, the audio is heard again.  
WLAN IP Handset 2210/2211/2212 User Guide  
       
40 Chapter 4 Features, functions, and buttons  
To make a call during a Push-to-Talk call  
A call can be made while in a Push-to-Talk call.  
1
2
Press  
.
The Push-to-Talk session is pre-empted.  
After the call is over, press  
as usual to go back on-hook.  
The Push-to-Talk session goes out of pre-empted mode and becomes active again. If an active  
Push-to-Talk call has not ended, the audio is heard again.  
NN40050-101  
 
41  
Chapter 5  
Troubleshooting  
This section describes the options to view specific information about your WLAN Handset and  
error messages displayed by your WLAN Handset. This information is useful in troubleshooting  
numerous problems.  
This section contains information about:  
View system information  
The System Info option enables the user to view information about the system. It displays:  
handset IP address  
server IP address  
handset firmware version  
To view the handset IP address  
1
2
3
4
5
6
Press  
when the handset is in the standby state.  
Press the Up and Down buttons to scroll through the menu and highlight System Info.  
Press the Select button (or OK) to select System Info.  
Press the Up and Down buttons to scroll through the menu and highlight Phone IP Addr.  
Press the Select button (or OK) to select Phone IP Addr.  
Do one of the following:  
Press UP to return to the previous menu and configure another option.  
Press to exit all menus and return to the standby state.  
You can also press Exit from the top-level menu to exit the menu and return to the active  
(off-hook) state.  
WLAN IP Handset 2210/2211/2212 User Guide  
         
42 Chapter 5 Troubleshooting  
To view the server IP address  
1
Press  
when the handset is in the standby state.  
2
Press the Up and Down buttons to scroll through the menu and highlight System Info.  
3
4
5
6
Press the Select button (or OK) to select System Info.  
Press the Up and Down buttons to scroll through the menu and highlight Server IP Addr.  
Press the Select button (or OK) to select Server IP Addr.  
Do one of the following:  
Press UP to return to the previous menu and configure another option.  
Press to exit all menus and return to the standby state.  
You can also press Exit from the top-level menu to exit the menu and return to the active  
(off-hook) state.  
To view the handset firmware version  
1
2
3
4
5
6
Press  
when the handset is in the standby state.  
Press the Up and Down buttons to scroll through the menu and highlight System Info.  
Press the Select button (or OK) to select System Info.  
Press the Up and Down buttons to scroll through the menu and highlight Firmware Version.  
Press the Select button (or OK) to select Firmware Version.  
Do one of the following:  
Press UP to return to the previous menu and configure another option.  
Press to exit all menus and return to the standby state.  
You can also press Exit from the top-level menu to exit the menu and return to the active  
(off-hook) state.  
View the current call server IP address  
The Current Call Svr option enables the user to view information about the call server in use. You  
cannot change the settings.  
To view the current call server  
1
2
3
Press  
when the handset is in the standby state.  
Press the Up and Down buttons to scroll through the menu and highlight Current Call Svr.  
Press the Select button (or OK) to select Current Call Svr.  
NN40050-101  
           
Chapter 5 Troubleshooting 43  
4
Do one of the following:  
Press UP to return to the previous menu and configure another option.  
Press to exit all menus and return to the standby state.  
You can also press Exit from the top-level menu to exit the menu and return to the active  
(off-hook) state.  
View terminal type  
The Terminal Type option shows the handset type used by the system. The Terminal Type option  
is for display purposes only. You cannot edit this option.  
To view the terminal type  
1
2
3
4
Press  
when the handset is in the standby state.  
Press the Up and Down buttons to scroll through the menu and highlight Terminal Type.  
Press the Select button (or OK) to select Terminal Type.  
Do one of the following:  
Press UP to return to the previous menu and configure another option.  
Press to exit all menus and return to the standby state.  
You can also press Exit from the top-level menu to exit the menu and return to the active  
(off-hook) state.  
View extension  
The Extension option enables the user to view the extension number for the WLAN Handset. This  
number is used to identify the handset. It displays when the handset is in the standby state.  
Note: The extension for the handset cannot be changed on the handset.  
WLAN IP Handset 2210/2211/2212 User Guide  
           
44 Chapter 5 Troubleshooting  
To view the extension number  
1
2
3
4
Press  
when the handset is in the standby state.  
Press the Up and Down buttons to scroll through the menu and highlight Extension.  
Press the Select button (or OK) to select Extension.  
Do one of the following:  
Press UP to return to the previous menu and configure another option.  
Press to exit all menus and return to the standby state.  
You can also press Exit from the top-level menu to exit the menu and return to the active  
(off-hook) state.  
Display messages  
The following table lists the messages that can appear on your WLAN Handset. If a message  
appears that cannot be resolved, contact your system administrator.  
Table 5 WLAN Handset messages, descriptions, and actions  
Message  
Description  
Action  
3 chirps  
WLAN Handset is not able to  
None. This is only a warning. The call will  
communicate with the best access point, handoff to the best access point once it  
probably because that access point has becomes available.  
no bandwidth available.  
Address Mismatch  
The WLAN Handset software download Contact your system administrator.  
files are incorrect or corrupted.  
ASSERT xxxx.c  
Line yyy  
The WLAN Handset has detected a fault Record the error information and contact  
from which it cannot recover.  
your system administrator.  
Assoc Failed  
xxxxxxxxxx  
The WLAN Handset association was  
refused by the Access Point.  
Record the error information and contact  
your system administrator.  
Assoc Timeout  
xxxxxxxxxx  
The WLAN Handset did not receive an  
association response from the Access  
Point.  
Record the error information and contact  
your system administrator.  
Auth Failed  
xxxxxxxxxx  
The WLAN Handset authentication was Record the error information and contact  
refused by the access point.  
your system administrator.  
Auth Timeout  
xxxxxxxxxx  
The WLAN Handset did not receive  
authentication from the access point.  
Record the error information and contact  
your system administrator.  
Bad Code Type xxx  
Expected Code Type yyy  
The WLAN Handset software does not  
match the current handset license  
selection.  
Record the error information and contact  
your system administrator.  
Bad Config  
Some needed configuration parameter  
has not been configure.  
Contact your system administrator.  
Bad ESSID  
The WLAN Handset is configured wrong. Contact your system administrator.  
The WLAN Handset is configured wrong. Contact your system administrator.  
The WLAN Handset is configured wrong. Contact your system administrator.  
Bad Local ID  
Bad Local ID Type  
NN40050-101  
     
Chapter 5 Troubleshooting 45  
Table 5 WLAN Handset messages, descriptions, and actions  
Message  
Description  
Action  
Bad Network IP  
The WLAN Handset is configured wrong. Contact your system administrator.  
The WLAN Handset is configured wrong. Contact your system administrator.  
Bad Network Mask  
Bad Payload Type  
There may be a configuration problem  
with the handset of the VPN server.  
Contact your system administrator.  
Bad Phintl File  
The WLAN Handset software download Contact your system administrator.  
files are incorrect or corrupted.  
Bad Program File  
The WLAN Handset software download Contact your system administrator.  
files are incorrect or corrupted.  
Bad Preshared Key  
Bad Tunneled IP  
The WLAN Handset is configured wrong. Contact your system administrator.  
The WLAN Handset is configured wrong. Contact your system administrator.  
The WLAN Handset is configured wrong. Contact your system administrator.  
Bad VPN Server IP  
B or A icon  
Battery Low message  
and beep  
Low battery  
In call: the battery icon (B) displays  
and a soft beep is heard when the user is  
on the WLAN Handset and the battery  
charge is low. User has 15–30 minutes of  
battery life left.  
Not in call: The battery icon (A)  
displays whenever the battery charge is  
low. The message Low Battery and a  
beep indicate a critically low battery  
charge. The WLAN Handset will not work  
until the battery pack is charged.  
Battery Failure  
Battery Failed  
The battery pack is not functioning.  
Replace the battery pack with a new or  
confirmed Nortel battery pack. Any  
non-Nortel battery packs will not work.  
The battery pack is damaged or  
incompatible with the WLAN Handset.  
Replace the battery pack with a new or  
confirmed Nortel battery pack. Any  
non-Nortel battery packs will not work.  
Can’t Renew DHCP  
yyy.yyy.yyy.yyy  
The DHCP server is not responding to  
the initial renewal attempt.  
Record the error information and contact  
your system administrator.  
Charging …  
The WLAN Handset is charging in the  
Desktop Charger.  
No action needed.  
Charge Complete  
The WLAN Handset is now fully charged. No action needed.  
Checking Code  
The WLAN Handset is checking for a  
newer version of software that should be approximately one second. If message  
None. This message lasts for  
downloaded.  
remains displayed, power off the WLAN  
Handset and contact your system  
administrator.  
Checking DHCP IP  
CRC Code Error  
The WLAN Handset is retrieving DHCP  
information from the DHCP server.  
None. This is informational only.  
The software which has been TFTP  
downloaded has a bad redundancy code  
check.  
Contact your system administrator.  
Code Mismatch!  
The software loaded into the WLAN  
Handset is incorrect for the handset  
model.  
Contact your system administrator.  
WLAN IP Handset 2210/2211/2212 User Guide  
46 Chapter 5 Troubleshooting  
Table 5 WLAN Handset messages, descriptions, and actions  
Message  
Description  
Action  
DCA Timeout  
The WLAN Handset has detected a fault Turn the WLAN Handset off, then on  
for which is cannot recover, possibly due again. If the error persists, contact your  
to a failure to acquire any network.  
system administrator.  
DHCP Error (1-5)  
DHCP Error 1  
The WLAN Handset cannot locate a  
DHCP server. It will try every four  
seconds until a server is located.  
DHCP Error 2  
The WLAN Handset has not received a  
response from the DHCP server to a  
request for an IP address. It will retry until  
a DHCP server is found.  
DHCP Error 3  
DHCP Error 4  
The server refuses to lease the WLAN  
Handset an IP address. It will keep trying.  
The DHCP server offered the WLAN  
Handset a lease that is too short. The  
minimum lease time is 10 minutes. One  
hour is the minimum recommended lease  
time.  
The WLAN Handset will stop trying.  
Notify the system administrator.  
DHCP Error 5  
Failure during WEP Key rotation process  
(proprietary feature). Notify the system  
administrator.  
DHCP Lease Exp  
yyy.yyy.yyy.yyy  
DHCP is not responding to renewal  
attempts (at least one renewal  
succeeded).  
The WLAN Handset failed to renew its  
DHCP lease, either because the DHCP  
server is not running, or because the  
configuration has been changed by the  
administrator. The handset will attempt to  
negotiate a new lease, which will either  
work, or change to one of the DHCP  
errors.  
DHCP NACK error  
yyy.yyy.yyy.yyy  
The DHCP server explicitly refused  
renewal.  
The DHCP lease currently in use by the  
WLAN Handset is no longer valid, which  
forces the handset to restart. This  
problem should resolve itself after the  
restart. If it does not, the problem is in the  
DHCP server, and you should contact  
your system administrator.  
DL Not On Sector  
The WLAN Handset software download Contact your system administrator.  
files are incorrect or corrupted.  
DO NOT POWER OFF  
The WLAN Handset is in a critical section None. Do not remove the battery or  
of the software update.  
attempt to power off the WLAN Handset  
while this is displayed. Doing so may  
require the handset to be returned to  
Nortel to be recovered.  
Duplicate IP  
Erase Failed  
The WLAN Handset has detected  
another device with the same IP  
Address.  
Contact your system administrator.  
Download process failed to erase the  
memory in the WLAN Handset.  
If error “int. error: 0F” is displayed, turn  
the WLAN Handset off, then on again. If  
error persists, contact your system  
administrator.  
NN40050-101  
Chapter 5 Troubleshooting 47  
Table 5 WLAN Handset messages, descriptions, and actions  
Message  
Description  
Action  
Erasing memory  
The WLAN Handset has determined that None. When the progress bar fills the  
a download should occur and is erasing display line, the erase operation is  
the current software from memory.  
complete.  
Do not turn the WLAN Handset off  
during this operation.  
Files Too Big  
The WLAN Handset software download Contact your system administrator.  
files are incorrect or corrupted.  
Flash Config Error  
Initializing …  
The WLAN Handset is configured wrong. Contact your system administrator.  
The WLAN Handset is performing power None. This is informational only.  
on initialization.  
Internal Err. # #  
The WLAN Handset has detected a fault Record the error code so it can be  
from which it cannot recover.  
reported. Turn the WLAN Handset off,  
then on again. If error persists, contact  
your system administrator.  
Invalid ID Info  
The VPN server did not recognize yo.  
Contact your system administrator.  
Multiple SVP Svr  
yyy.yyy.yyy.yyy  
The WLAN Handset is attempting to  
communicate with two WLAN IP  
Telephony Managers 2245.  
If this persists, record the information and  
contact your system administrator.  
Must Upgrade SW!  
The WLAN Handset software is  
incompatible with the hardware.  
Contact your system administrator.  
Try call again later.  
Net Busy  
All access points are full or busy.  
xxxxxxxxxx  
No DHCP Server  
The WLAN Handset is unable to contact Contact your system administrator  
the DHCP server.  
No ESSID  
The WLAN Handset is configured wrong. Contact your system administrator.  
No Func Code  
The WLAN Handset software download Contact your system administrator.  
files are incorrect or corrupted.  
No Host IP xxxxxxxxxx  
No IP Address  
The WLAN Handset is configured wrong. Contact your system administrator.  
Invalid IP address.  
Contact your system administrator.  
Contact your system administrator.  
No Net Access  
Cannot authenticate/associate with  
access point  
No Net Found  
Can be caused by a variety of issues  
Contact your system administrator.  
No Net Found xxxxxxxxxxx yy The WLAN Handset cannot find a  
suitable access point.  
Record the error information and contact  
your system administrator.  
No PBX Response  
The WLAN Handset tried to send a  
message to the Call Server and failed to  
get a response.  
Contact your system administrator.  
No Proposal  
No Reg Domain  
No SVP IP  
The WLAN Handset is configured wrong. Contact your system administrator.  
Regulatory Domain not configure Contact your system administrator.  
The WLAN Handset is configured wrong. Contact your system administrator.  
The WLAN Handset has lost contact with If the problem persists, record the error  
No SVP Response  
yyy.yyy.yyy.yyy  
the SVP server.  
information and contact your system  
administrator.  
No SVP Server  
The WLAN Handset is configured wrong. Contact your system administrator.  
WLAN IP Handset 2210/2211/2212 User Guide  
48 Chapter 5 Troubleshooting  
Table 5 WLAN Handset messages, descriptions, and actions  
Message  
Description  
Action  
No SVPServer  
No DNS Entry  
The WLAN Handset was unable to  
perform DNS lookup for the SVP Server,  
the server had no entry for the SVP  
server.  
Contact your system administrator.  
No SVPServer  
No DNS IP  
The WLAN Handset was unable to  
perform DNS lookup for the SVP Server,  
no IP Address for the SVP server.  
Contact your system administrator.  
No SW Found  
A required software component has not Contact your system administrator.  
been properly installed.  
No UNISTIM DHCP  
No VPN Server  
Not Installed!  
The WLAN Handset is configured wrong. Contact your system administrator.  
The WLAN Handset is configured wrong. Contact your system administrator.  
A required software component has not Contact your system administrator.  
been properly installed.  
Payload Malfmd  
Press End Call  
The WLAN Handset is configured wrong. Contact your system administrator.  
The far end of a call has hung up.  
Hang up the near end.  
Restart Command  
The WLAN Handset received a restart  
command from the server.  
None. The WLAN Handset will  
automatically restart in a few seconds.  
RTP Open Failed  
The WLAN Handset encountered an  
error in connecting to the Call Server.  
Power off and then power on the  
handset. If the problem persists, contact  
your system administrator.  
Select License  
Server Busy  
The WLAN Handset is configured wrong. Contact your system administrator.  
The WLAN Handset is attempting to  
download from a TFTP Server that is  
busy downloading other devices and  
refusing additional downloads.  
None. The WLAN Handset will  
automatically retry the download every  
few seconds.  
SKT Open Failed  
The WLAN Handset encountered an  
error in connecting to the Call Server.  
If the problem persists, contact your  
system administrator.  
Storing Config  
The WLAN Handset is storing changes to None. This is informational only.  
the handset configuration.  
SVP Service Rej.  
The SVP Server has rejected a request If the problem persists, contact your  
from the WLAN Handset.  
system administrator.  
System Busy yyy.yyy.yyy.yyy  
The Server has reached its call capacity. All call paths are in use. Try the call again  
in a few minutes.  
System Locked (with Busy  
Tone)  
System is locked  
Try the call again, system has been  
locked for maintenance.  
TFTP ERROR(x):yy  
A failure has occurred during a software Power off the WLAN Handset, then turn it  
download.  
on again to retry the download.  
If the error persists, contact your system  
administrator.  
Too Many Errors  
The WLAN Handset continues to reset  
and cannot be recovered.  
Contact your system administrator.  
Unknown xx:yy:zz  
Updating …  
A phrase is missing from a download file. Contact your system administrator.  
The WLAN Handset is internally updating None. The handset may do this briefly  
its software images.  
after a download. This is informational  
only.  
NN40050-101  
Chapter 5 Troubleshooting 49  
Table 5 WLAN Handset messages, descriptions, and actions  
Message  
Description  
Action  
Updating Code …  
The WLAN Handset is downloading new None. Do not turn the WLAN Handset off  
software into memory. The number icons during this operation.  
at the bottom of the display indicate  
which file number is currently being  
downloaded. This message also displays  
a progress bar. When the progress bar  
fills the display line, the update operation  
is complete on that file.  
VPN Error: xxx  
Waiting …  
The WLAN Handset encountered an  
error. The error message and code is  
displayed.  
Record the error information and contact  
your system administrator.  
The WLAN Handset has attempted some None. The WLAN Handset is waiting for  
operation several times and failed, and is a specified period of time before  
now waiting for a period of time before  
attempting that operation again.  
attempting that operation again.  
Watchdog Timeout  
Wrong Code Type.  
The WLAN Handset failed to hear from  
the supported VOIP solution within the  
watchdog timeout interval.  
Contact your system administrator.  
The software loaded into the WLAN  
Handset is incorrect for this model of  
handset.  
Contact your system administrator.  
WLAN IP Handset 2210/2211/2212 User Guide  
50 Chapter 5 Troubleshooting  
NN40050-101  
51  
Chapter 6  
WLAN Handset, headset, batteries, chargers, and  
accessories  
This section contains information about:  
Cleaning your WLAN Handset  
The WLAN Handset occasionally must be cleaned to maintain appearance. In general, wiping the  
handset surface with a clean water-dampened cloth or paper towel removes most films or residues.  
If more rigorous cleaning is required, you can use:  
A mild detergent solution. Be sure to wipe away any detergent residue with a plain  
water-dampened cloth.  
Any general-purpose household glass and surface cleaner. Do not spray the handset directly.  
Spray the cleaner on a soft cloth or paper towel, then wipe the handset.  
Pre-treated cloths, like those used for eyeglasses or cameras.  
Pre-moistened towelettes. Avoid those containing lanolin or aloe, which leave a slippery  
residue.  
Isopropyl alcohol, applied by a damp cloth or paper towel. When using alcohol, do not rub the  
keypad characters vigorously, as this will significantly degrade legibility.  
IMPORTANT!  
Do not use furniture polishes, waxes, or plasticizer-based cleaner.  
Do not use lanolin, aloe, glycerin, or other skin care products.  
Do not apply any solvent such as acetone or mineral spirits.  
Do not directly spray or immerse the handset.  
If the headset connector becomes dirty, you may experience a scratchy or intermittent signal. To  
clean the connector, dip the padded end of either a wooden- or paper-handled cotton swab in  
isopropyl alcohol. Gently insert in the connector and twist, repeating several times. If available,  
blow compressed air into the connector to clear debris.  
WLAN IP Handset 2210/2211/2212 User Guide  
     
52 Chapter 6 WLAN Handset, headset, batteries, chargers, and accessories  
Headset  
Nortel offers optional headsets, with a quick-disconnect jack, for use in noisy environments or for  
use if you need to have your hands free while talking. The headset is not available in all regions.  
To use the headset, simply plug it into the jack on the bottom of your WLAN Handset. If the  
headset is disconnected using the quick-disconnect jack, there is no audio connection on the  
headset or the speaker and microphone in the WLAN Handset.  
The headset is specifically designed to work with the WLAN Handset. Nortel does not recommend  
using other headsets.  
The following figure shows the headset jack for the WLAN Handset.  
Figure 4 WLAN Handset bottom view  
IMPORTANT!  
The only authorized headsets that can be used with WLAN Handset are  
those obtained from Nortel, Plantronics, or their reseller partners.  
Battery packs  
The battery pack for the WLAN Handset must be recharged periodically. The  
WLAN Handset 2210 and WLAN Handset 2211 use Nickel Metal Hydride (NiMH) rechargeable  
battery packs, while the WLAN Handset 2212 uses a Lithium ion rechargeable battery pack. The  
battery packs provide four hours of talk time or 70 hours of standby time. Standby time is when the  
handset is turned on, but not in an active call.  
Battery packs are not interchangeable. Use only the battery made for your handset.  
The following figures show the location of the battery packs on the handsets.  
NN40050-101  
       
Chapter 6 WLAN Handset, headset, batteries, chargers, and accessories 53  
Figure 5 WLAN Handset 2210 and 2212 battery pack location  
Low battery indicators  
The WLAN Handset notifies you when the charge on the battery pack is low by displaying the  
battery icon (B). If you are not in a call, you hear a loud beep. If you are in a call, you hear a soft  
beep through the earpiece every six seconds. At this point, your handset has 15 to 30 minutes of  
battery life left.  
The low battery icon (A), the Low Battery message in the display area and a loud beep indicate a  
critically low charge. The handset will not work until the battery pack is charged.  
Remove and insert the battery pack  
To remove the battery pack  
For the WLAN Handset 2210 and WLAN Handset 2212:  
1
To release the battery pack, press down on the latch on the battery pack.  
For the WLAN Handset 2211:  
1
2
To release the battery pack, hold the handset in one hand, with the keys facing up.  
Press both battery release buttons on the left and right sides of the handset with your other  
hand.  
The battery pack should drop into your hand.  
Note: Do not pry the battery out of the handset.  
WLAN IP Handset 2210/2211/2212 User Guide  
             
54 Chapter 6 WLAN Handset, headset, batteries, chargers, and accessories  
To insert the battery pack  
For the WLAN Handset 2210 and WLAN Handset 2212:  
1
2
Slide the lower lip of the battery pack into the bottom of the handset cavity.  
Push the top of the battery pack in place.  
For the WLAN Handset 2211:  
1
Slide the battery pack straight into the cavity until it snaps into place.  
Note: Do not force the battery pack into the handset.  
To change the battery pack while in a call  
1
2
3
4
Use Call Park to park the current call.  
Quickly remove the discharged battery pack and replace it with a charged battery pack.  
Press  
to turn the handset back on.  
Use Call Park to retrieve the parked call.  
Desktop Charger  
The Nortel WLAN Handset Desktop Charger is designed to fully charge the battery packs in  
approximately two hours. The charger operates in a 50° to 85° F (10° to 30° C) environment. Do  
not expose the charger to freezing temperatures or direct sunlight.  
Desktop chargers are not interchangeable. Use only the charger made for your handset.  
Desktop chargers are available for the WLAN Handset 2210 and WLAN Handset 2211 only.  
The following figure shows the WLAN Handset 2210 and 2211 Desktop Chargers.  
NN40050-101  
         
Chapter 6 WLAN Handset, headset, batteries, chargers, and accessories 55  
Figure 6 The WLAN Handset 2210, and WLAN Handset 2211 Desktop Chargers  
WLAN Handset 2211  
WLAN Handset 2210  
The charger is shipped with the appropriate power supply for the site. Place the charger on a flat,  
horizontal surface. Plug the power supply into the charger and into an appropriate wall outlet.  
IMPORTANT!  
Do not place anything in the Desktop Charger other than the correct WLAN  
Handset. Doing so might damage the contacts. Bent contacts can keep the  
WLAN Handset from charging.  
Using the Desktop Charger  
To charge the WLAN Handset Desktop Charger  
1
2
Press  
to terminate any calls. The handset can be off or in standby mode during charging.  
Place the handset, face forward, into the Desktop Charger.  
The red indicator light turns on.  
The indicator light does not come on when the charger slot is empty, when the handset is not  
inserted properly, or when the charger has no power.  
3
4
Charge the battery pack.  
If the handset is in standby mode, it displays its extension number and Charging…. It is fully  
operational and can receive calls. If the handset is off, only Charging… displays and the  
handset cannot receive calls.  
It is normal for the battery pack to become warm when charging.  
When the handset is fully charged, Charge Complete displays. Remove the handset from the  
charger.  
The red indicator light remains on until the handset is removed from the charger.  
WLAN IP Handset 2210/2211/2212 User Guide  
       
56 Chapter 6 WLAN Handset, headset, batteries, chargers, and accessories  
Dual Charger  
The Nortel WLAN Handset Desktop Chargers are designed to fully charge the handset and one  
spare battery pack in approximately two hours (each). The charger operates in a 50° to 85° F (10°  
to 30° C) environment. Do not expose the charger to freezing temperatures or direct sunlight.  
Dual chargers are not interchangeable. Use only the charger made for your handset.  
Dual chargers are available for the WLAN Handset 2210, WLAN Handset 2211 and  
WLAN Handset 2212.  
The following figure shows the WLAN Handset 2211 and spare battery pack in its Dual Charger.  
Figure 7 WLAN Handset 2211 Dual Charger  
The Dual Charger is shipped with the appropriate power supply for the site. Place the Dual  
Charger on a flat, horizontal surface. Plug the power supply into the Dual Charger and into an  
appropriate wall outlet.  
IMPORTANT!  
Do not place anything in the Dual Charger other than the correct WLAN  
Handset. Doing so might damage the contacts. Bent contacts can keep the  
WLAN Handset from charging.  
The handset and spare battery cannot charge simultaneously. If both require charging, the handset  
has priority and will recharge first. After the handset is fully charged, the spare battery will be  
charged.  
NN40050-101  
 
Chapter 6 WLAN Handset, headset, batteries, chargers, and accessories 57  
Using the Dual Charger  
To charge the WLAN Handset Dual Charger  
1
2
Press  
to terminate any calls. The handset can be off or in standby mode during charging.  
Place the handset, face forward, into the handset charging bay of the Dual Charger.  
The red indicator light turns on.  
The indicator light does not come on when the charger slot is empty, when the handset is not  
inserted properly, or when the charger has no power.  
3
4
Charge the handset battery.  
If the handset is in standby mode, it displays its extension number and Charging…. It is fully  
operational and can receive calls. If the handset is off, only Charging… displays and the  
handset cannot receive calls.  
It is normal for the battery pack to become warm when charging.  
When the handset is fully charged, Charge Complete displays. Remove the handset from the  
charger.  
The red indicator light remains on until the handset is removed from the charger.  
To charge a battery pack  
1
Remove the battery from the handset, as described in “Remove and insert the battery pack” on  
2
Insert the battery pack into the battery charging bay of the Dual Charger.  
The red indicator light turns on.  
The indicator light does not come on when the charger slot is empty, when the handset is not  
inserted properly, or when the charger has no power.  
If the indicator light starts blinking as soon as the battery pack is inserted, remove the battery  
pack and reinsert it into the charger.  
If the indicator light continuously blinks during the charging process, the battery pack is  
unusable. Properly dispose of the unusable battery pack.  
3
4
Charge the battery pack.  
It is normal for the battery pack to become warm when charging.  
When charging is complete, the indicator light turns off. Remove the battery pack from the  
charger.  
Quad Charger  
The Nortel WLAN Handset Quad Chargers fully charge up to four battery packs in approximately  
two hours. Chargers operate in a 50° to 85° F (10° to 30° C) environment. Do not expose them to  
freezing temperatures or direct sunlight.  
WLAN IP Handset 2210/2211/2212 User Guide  
             
58 Chapter 6 WLAN Handset, headset, batteries, chargers, and accessories  
Quad chargers are not interchangeable. Use only the charger made for your handset.  
Quad chargers are available for the WLAN Handset 2211 and WLAN Handset 2212.  
The Quad Charger comes with the appropriate power supply for the site. Place the Quad Charger  
on a flat, horizontal surface. Plug the power supply into the Quad Charger and into an appropriate  
wall outlet.  
IMPORTANT!  
Do not place anything in the Quad Charger other than the correct WLAN  
Handset. You might damage the contacts. Bent contacts can keep the battery  
packs from charging.  
Using the Quad Charger  
To charge the battery pack  
1
Remove the battery pack from the handset, following the steps in “To remove the battery pack”  
2
Insert the battery pack into one of the four charging bays.  
The LED above the charging bay turns on. If the LED starts blinking as soon as the battery  
pack is inserted, remove the battery pack and reinsert it into the charger.  
If the LED continuously blinks during the charging process, the battery pack is unusable.  
Properly dispose of the unusable battery pack.  
3
When charging is complete, the LED turns off. Remove the battery pack from the charger.  
Cleaning the Desktop, Dual or Quad Chargers  
Clean the Desktop, Dual or Quad Charger by wiping the surface with a clean, water-dampened  
cloth or paper towel. A mild detergent solution can be used. Be sure to wipe away any detergent  
residue with a plain water-dampened cloth.  
CAUTION  
Unplug the charger before attempting to clean it.  
Do not immerse the charger in water or other liquid.  
Do not pour liquids into the charger slot.  
NN40050-101  
         
Chapter 6 WLAN Handset, headset, batteries, chargers, and accessories 59  
Cleaning the WLAN Handset contacts  
The battery pack contacts on the WLAN Handset can be cleaned with isopropyl (rubbing) alcohol  
applied with a cotton swab, cloth, or paper towel. Do not push or pull the exposed battery pack  
contacts.  
IMPORTANT!  
Always use the Desktop Charger provided to charge the battery pack.  
Other chargers can damage the battery pack.  
Only use the original plug-in power adapter for the Desktop Charger.  
Do not dip the battery pack in water or throw into the fire.  
Do not dispose of the battery pack with your domestic waste. Take used  
battery packs to an appropriate collection point for recycling or send them  
back to your supplier or servicing agent.  
Replacement battery packs are available from your supplier or servicing  
agent.  
Accessories  
Optional accessories for the handset are:  
carrying case  
belt clip  
For further information, consult the documentation supplied with the accessory.  
WLAN IP Handset 2210/2211/2212 User Guide  
   
60 Chapter 6 WLAN Handset, headset, batteries, chargers, and accessories  
NN40050-101  

JVC AV 21MX16 User Manual
JVC DIGIPURE HV L34PRO User Manual
LG Electronics LG Life Good Computer Monitor M1962D User Manual
Motorola MA360 Series User Manual
NEC MultiSync LCD1970NX User Manual
Panasonic Cordless Telephone KX TG7873 User Manual
Philips 21GR1250 User Manual
Philips CD1502B User Manual
Philips Computer Monitor 19S4LM User Manual
Philips DFU TS3258 User Manual