Network Technologies CRYSTALMON CM RK17 User Manual

1275 Danner Dr Tel:330-562-7070  
R NETWORK  
Fax:330-562-1999  
TECHNOLOGIES Aurora, OH 44202  
INCORPORATED  
NTI  
CRYSTALMONTM Series  
CM-RK17  
CM-WL17  
CM-DT17  
TFT/LCD MONITOR  
Installation and Operation Manual  
MAN058 Rev Date 12/5/2008  
TABLE OF CONTENTS  
Introduction....................................................................................................................................................................1  
Overview......................................................................................................................................................................1  
Features.......................................................................................................................................................................1  
Materials.........................................................................................................................................................................2  
Precautions....................................................................................................................................................................3  
Cleaning.......................................................................................................................................................................3  
Features and Functions................................................................................................................................................4  
Installation......................................................................................................................................................................6  
Mounting......................................................................................................................................................................6  
Rack Mount...............................................................................................................................................................6  
Wall Mount- with Arm................................................................................................................................................6  
Wall Mount- Direct-To-Wall.......................................................................................................................................7  
Desktop Mount..........................................................................................................................................................7  
Power Supply Bracket ..............................................................................................................................................8  
Cable Connections ......................................................................................................................................................8  
Connect the CRYSTALMON to a Video Source.......................................................................................................8  
Power Up.....................................................................................................................................................................9  
Display Functions .......................................................................................................................................................10  
Standard Controls......................................................................................................................................................10  
OSD Control Menu ....................................................................................................................................................11  
OSD Main Menu .....................................................................................................................................................11  
Brightness/Contrast Menu ......................................................................................................................................11  
Setup Menu.............................................................................................................................................................12  
Specifications..............................................................................................................................................................13  
LCD............................................................................................................................................................................13  
Display Controller ......................................................................................................................................................13  
OSD Control Board....................................................................................................................................................13  
Enclosure...................................................................................................................................................................13  
General Specs...........................................................................................................................................................13  
Compliance Certifications..........................................................................................................................................13  
Dimensions..................................................................................................................................................................14  
Troubleshooting..........................................................................................................................................................15  
Index .............................................................................................................................................................................15  
Warranty Information..................................................................................................................................................16  
ii  
MAN058 Rev Date 12/5/2008  
TABLE OF FIGURES  
Figure 1- Mount CM-RK17 to a rack ...............................................................................................................................6  
Figure 2- Mount CM-WL17 to an arm or bracket ............................................................................................................7  
Figure 3- Secure cables to power supply bracket...........................................................................................................8  
Figure 4- Connect VGA and/or DVI video sources .........................................................................................................8  
Figure 5- Connect the AC adapter ..................................................................................................................................9  
Figure 6- CRYSTALMON Controls ...............................................................................................................................10  
iii  
MAN058 Rev Date 12/5/2008  
NTI CRYSTALMON TFT/LCD MONITOR  
INTRODUCTION  
Overview  
The CRYSTALMON series TFT/LCD monitors provide the industrial or commercial user with superior picture  
quality, multiple video formats, and a sturdy industrial enclosure. It also offers several mounting options, as well as  
the ability to integrate with existing NTI products. The CRYSTALMON monitor can be ordered with provisions for  
rack, wall, or tabletop mounting. They support true plug-and-play functionality and do not require any additional video  
drivers or interface adapters.  
Models Available:  
CM-RK17- Standard 17" TFT/LCD monitor for rack mount  
CM-WL17- Standard 17" TFT/LCD monitor for wall or arm mounting  
CM-DT17- Standard 17" TFT/LCD monitor with desktop stand  
Features  
An industrial 17" TFT/LCD flat panel monitor.  
Support of multiple video formats-VGA,SVGA, and XGA  
On Screen Display (OSD).  
Crisp and clear 1280x1024 video resolution.  
Wall / VESA Mount (CM-WL17)  
Keyholes for mounting to a wall.  
Compliant to VESA 75mm and 100mm mounting hole patterns.  
Compatible with NTI's LCD arms.  
Rack Mount (CM-RK17)  
Designed to fit in a standard 19" rack/cabinet.  
Space-saving. Extra rackmounting space available behind the monitor.  
7RU (12.25") high.  
Tabletop (CM-DT17)  
Adjust height, tilt and rotation of monitor for best viewing position.  
Power Supply Carriage  
Supports multiple languages  
1
NTI CRYSTALMON TFT/LCD MONITOR  
MATERIALS  
Materials supplied with this kit:  
9
9
9
9
9
9
9
9
9
NTI CRYSTALMON TFT/LCD Monitor  
120 or 240VAC at 50 or 60Hz-12VDC/5A via AC Adapter  
Power Supply Holder  
2- Cable clamps  
4- #4-40 x 3/16” black Phillips-panhead screws  
6 foot VGA cable-VEXT-6-MM (15HD male-male connectors)  
6.5 foot DVI video cable-DVI-DS-2M-MM (DVI-D single link male-male connectors)  
Desktop stand (provided with CM-DT17 only)  
CD with a pdf file of this owner's manual  
Additional materials may need to be ordered, depending upon the configuration :  
¾
Wall Mount Arm Bracket- for mounting the CRYSTALMON (CM-WL17) to a wall- several configurations are  
available. See our website at http://www.networktechinc.com for details.  
Contact your nearest NTI distributor or NTI directly for all of your KVM needs at 800-742-8324 (800-RGB-TECH) in  
US & Canada or 330-562-7070 (Worldwide) or at our website at http://www.networktechinc.com and we will be happy  
to be of assistance.  
2
NTI CRYSTALMON TFT/LCD MONITOR  
PRECAUTIONS  
Do not apply pressure to the display portion of the CRYSTALMON because the LCD panel and backlight can be  
easily damaged.  
Do not cover or block the vent holes in the case.  
Be sure to turn OFF the power supply before connecting and disconnecting video source cable(s).  
Be careful not to drop the CRYSTALMON. Handle it carefully.  
Do not store or install the CRYSTALMON where it can come in contact with moisture as moisture may damage  
the CRYSTALMON.  
Store the CRYSTALMON in an environment within a temperature range of 0ºC to 40ºC and where humidity will  
not exceed 90% relative humidity. Excessive temperature and humidity may reduce the performance of the  
CRYSTALMON.  
Install the CRYSTALMON in a clean environment as dust and oil may cause electrical shorts or otherwise  
damage the CRYSTALMON.  
FOR INDOOR USE ONLY. DO NOT INSTALL OUTDOORS.  
The CRYSTALMON contains mercury (Hg). Dispose of the CRYSTALMON in accordance with local  
ordinances.  
Cleaning  
Use a soft cloth (such as microfiber) without chemicals for cleaning. The display surface of the CRYSTALMON  
is very soft and easily scratched.  
Do not apply excessive pressure to the display screen surface when cleaning. Excessive pressure may damage  
the LCD panel and backlight.  
3
NTI CRYSTALMON TFT/LCD MONITOR  
FEATURES AND FUNCTIONS  
1
2
3
4
5
6
TM  
CRYSTALMON  
NTI  
Main Controls  
1. Power Button- to turn the LCD and backlight ON and OFF.  
2. Power LED- to indicate the power status of the monitor  
Green= Power On, Video Input OK  
Red= Suspend/Standby, or Input Out of Range  
3. Menu Button- to open OSD menu (when OSD menu is OFF)  
4. Arrow Up Button- to move the selection cursor in the OSD menu up in the list  
5. Arrow Down Button- to move the selection cursor in the OSD menu down in the list  
6. Select Button- to select a menu item (when OSD menu is ON) or press to auto adjust the video quality (when  
OSD menu is OFF)  
4
NTI CRYSTALMON TFT/LCD MONITOR  
REAR VIEW OF CRYSTALMON  
R
NETWORK  
TECHNOLOGIES  
INCORPORATED  
1275 Danner Dr Tel:330-562-7070  
Aurora, OH 44202 Fax:330-562-1999  
NTI  
10  
12VDC  
5A  
+
-
DVI  
VGA  
7
8
9
7. 12VDC Power Jack- for connection of AC adapter  
8. DVI Video Port- DVI-D female- for connecting DVI type video source  
9. VGA Video Port- 15HD female- for connecting VGA type video source  
10. Power Supply Holder - for supporting the power supply (when desktop or rack-mounted)  
5
NTI CRYSTALMON TFT/LCD MONITOR  
INSTALLATION  
Mounting  
Mount the CRYSTALMON as intended for the application.  
Rack Mount  
Secure the CRYSTALMON (model CM-RK17) to a rack using appropriate hardware through the holes provided (see  
Fig. 1). Mount using at least two screws on each side.  
Front View of CM-RK17  
Figure 1- Mount CM-RK17 to a rack  
Wall Mount- with Arm  
Mount the selected Wall Mount LCD Arm or bracket assembly to the wall. Attach the VESA mounting bracket from  
the selected Wall Mount LCD Arm to the four holes located in the back of the CRYSTALMON using the M4 x 10mm  
screws (4) provided. A set of holes is provided for either the 100mm bracket, or the 75mm bracket, whichever is  
needed (see Fig. 2). (The 75-100mm mounting adaptor that is sometimes provided will not be necessary.) Follow  
the instructions that came with the mounting arm or bracket to complete the assembly.  
6
NTI CRYSTALMON TFT/LCD MONITOR  
Alternate Power Supply  
Bracket location  
Keyholes for mounting directly to the wall  
Hole pattern for 100mm mounting  
Hole pattern for 75mm mounting  
R
NETWORK  
Note: Use only  
M4 x 10mm  
TECHNOLOGIES  
NTI  
INCORPORATED  
1275 Danner Dr Tel:330-562-7070  
Aurora, OH 44202 Fax:330-562-1999  
Power Supply  
Bracket  
screws (provided)  
in 75mm or  
12VDC  
5A  
100mm mounting  
holes. Use of longer  
screws may damage  
the CRYSTALMON.  
+
-
DVI  
VGA  
cable restraint posts  
Rear View of CRYSTALMON  
Figure 2- Mount CM-WL17 to an arm or bracket  
Wall Mount- Direct-To-Wall  
If it is desired to mount the CRYSTALMON directly to the wall (model CM-WL17), two keyhole slots have been  
provided on the back of the CRYSTALMON for this purpose (see Fig. 2).  
CAUTION: Each fastener used for direct wall mounting must be rated for an object weighing at least 24  
pounds.  
!
Desktop Mount  
If the CM-DT17 has been purchased, a desktop stand with installation instructions has been included. If using a  
different desktop stand, secure the stand to the CRYSTALMON using either the 75mm or 100mm mounting holes,  
as appropriate for the stand that has been purchased. The holes on the CRYSTALMON are intended for use with  
M4 x 10MM screws. Use only M4 x 10mm screws (provided) for attachment to the CRYSTALMON. See the  
instructions that come with the stand to complete the assembly.  
7
NTI CRYSTALMON TFT/LCD MONITOR  
Power Supply Bracket  
A power supply bracket has been supplied for the convenient mounting of the power supply for the CRYSTALMON.  
This bracket can be directly mounted to the CRYSTALMON. Two possible mounting locations are shown in Fig. 2 on  
Page 5.  
Two #4-40 x 3/16” black screws have been supplied to secure the bracket to the back of the CRYSTALMON. Two  
more #4-40 x 3/16” screws and cable clamps have been supplied to secure the cables to cable restraint posts on the  
power supply bracket (see Fig. 3.)  
Power Supply  
+
Cable to Monitor  
Cable Clamp  
(supplied)  
3/16" x 4-40  
Screw  
(supplied)  
+
Power Cord  
Power Supply  
Bracket  
Side View  
Figure 3- Secure cables to power supply bracket  
Cable Connections  
Connect the CRYSTALMON to a Video Source  
The CRYSTALMON is provided with two different connectors for direct connection to video sources. A video  
source of each type may be connected individually or both at the same time. The sources can be either VGA  
or DVI. See Fig. 4 for illustration of each type of cable to be connected.  
VIEW OF CONNECTIONS ON CRYSTALMON  
DVI-D Male  
Video Connector  
DVI-D Female  
15HD Female  
(Digital Video)  
(VGA,XGA,SXGA)  
To Digital  
Video Source  
DVI-DS-2M-MM  
(supplied)  
DVI-D Male  
To VGA Video  
Source  
VEXT-6-MM  
(supplied)  
15HD male  
Video Connector  
15HD Male  
Figure 4- Connect VGA and/or DVI video sources  
8
NTI CRYSTALMON TFT/LCD MONITOR  
Power Up  
1. Connect the AC adapter to the power jack on the CRYSTALMON. Make sure the power connector is fully  
inserted.  
2. Plug the AC adapter into a power source and press the power button to power up the CRYSTALMON.  
3. If the video source(s) are not yet ON, apply power to them at this time.  
Power  
Button  
REAR VIEW OF CRYSTALMON  
R
NE TWORK  
TECHNOLOGIES  
INCORPORATED  
1275 Danner Dr Tel:330-562-7070  
Aurora, OH 44202 Fax:330-562-1999  
www.networktechinc.com  
NTI  
12VDC  
5A  
+
-
DVI  
VGA  
View of the control  
buttons for the  
CRYSTALMON  
UNDERSIDE VIEW OF CRYSTALMON  
Barrel  
12 VDC  
AC  
ADAPTER  
IEC Connector  
IEC Power Cord  
Power Connector  
12VDC @ 5A OUTPUT  
(Outside  
barrel)  
(Inside  
barrel)  
2.5 mm x 5.5 mm Female  
Figure 5- Connect the AC adapter  
9
NTI CRYSTALMON TFT/LCD MONITOR  
DISPLAY FUNCTIONS  
The CRYSTALMON 17” monitor supports resolutions up to SXGA (1280x1024) with a refresh rate at between 55 and  
76Hz. The quality of the image on the LCD monitor is adjustable using an On Screen Display (OSD) menu using  
the control buttons on the CRYSTALMON.  
Standard Controls  
The CRYSTALMON has 5 standard control buttons and a power LED. The 5 standard control buttons operate  
as follows:  
The Power button turns the CRYSTALMON LCD and backlight ON and OFF as desired.  
The Power LED located immediately below the Power button is  
a dual color LED. It will illuminate with a green color when the  
CRYSTALMON is powered ON and working properly. It will  
illuminate with a red color if the CRYSTALMON is powered ON  
but there is no input signal detected. The LED will illuminate  
red only momentarily just before turning OFF.  
Power  
ON/OFF  
Power LED  
The Menu button is used to bring up the OSD menu where the  
various settings of the LCD display can be adjusted.  
Once the OSD screen is displayed, the Menu button is used  
to make selections within the menus. See "OSD Control Menu"  
on page 11 for more on LCD display settings.  
Menu  
Up Arrow  
Controls for the  
OSD Menus  
Down Arrow  
Select/  
Auto Adjust  
The Up and Down Arrow buttons are used to navigate through the  
menus. Move the cursor up or down as desired to highlight  
an item for selection. Once an item is highlighted, pressing the  
Menu button will select it.  
Figure 6- CRYSTALMON Controls  
Note: When the OSD Menu is OFF, the Up Arrow is used to toggle between a “PC” (VGA) and “Digital” (DVI)  
input source.  
The Select button is used to make selections within the OSD menus when the OSD menu is ON. When the  
OSD menu is OFF, the Select button will act as an Auto Adjust button to keep the user from having to use the  
menus to adjust the quality of the image on the monitor.  
Note: In order to display the OSD Menu, the CRYSTALMON must first be connected to a video source (see  
“Connect the CRYSTALMON to a Video Source” – page 8).  
Note: If the message “NO SIGNAL” appears when the monitor is powered-ON, the monitor may be set for a  
“PC” (VGA) input source. Press the Up Arrow button on the monitor to toggle the monitor input source  
setting to “Digital” (DVI).  
10  
NTI CRYSTALMON TFT/LCD MONITOR  
OSD Control Menu  
The OSD (On Screen Display) Menu enables the user to select the desired characteristics of the LCD display. To  
activate the OSD Menu, press the Menu button (above). To turn the Menu back OFF, either select "EXIT" from  
the main menu or just wait 10-60 seconds and it will automatically be cleared from the screen. Any changes made  
before exiting the menu will be saved.  
OSD Main Menu  
Note: In order to display the OSD Menu, the CRYSTALMON must first be connected to a video source (see  
“Connect the CRYSTALMON to a Video Source” – page 8).  
Note: If menu does not appear when the Menu button is pressed, the monitor may be connected to a DVI  
input source but set for a “PC” (VGA) input source. Press the Up Arrow button on the monitor to switch it  
to a “Digital” (DVI) input source.  
Selection  
Purpose  
Range  
Brightness/Contrast Increase/decrease panel brightness/contrast level  
1-100  
Setup  
Exit  
Control OSD Image position on screen  
Set time OSD will stay on screen before auto  
shutoff  
Select the language of the OSD menu  
Select Input Source to display  
0-4  
10 to 60 seconds  
English, Spanish, Deutsch, Italian, or  
French  
Digital or PC  
Exit from the OSD control menu  
Brightness/Contrast Menu  
Selecting the Brightness/Contrast menu will bring up a screen in which the user can adjust the brightness and  
contrast levels of the LCD display. Using the Up or Down arrows to navigate the menu, highlight either the  
BRIGHTNESS or CONTRAST sections and press the Select button to choose the option to adjust. Then use the  
Up or Down Arrow to adjust the setting.  
Select EXIT when finished to return to the Main Menu.  
11  
NTI CRYSTALMON TFT/LCD MONITOR  
Setup Menu  
Selecting the Setup menu will bring up a screen in which the user can adjust  
ƒ
ƒ
OSD POSITION-the position of the OSD menus on the LCD display (positions 0-4)  
OSD TIME-the length of time the user can be idle before the OSD menu automatically exits  
(adjustable from 10 to 60 seconds)  
ƒ
ƒ
LANGUAGE-the language that the OSD menus will be presented in  
INPUT SOURCE- the type of signal that is coming from the input source, either Digital (DVI) or PC  
(VGA)  
With the item highlighted, (use the Up or Down arrow to move between them), press the Select button to choose  
the option to adjust. Then use the Up or Down Arrow to adjust the setting as needed. Select EXIT when finished  
to return to the Main Menu.  
OSD Image can be moved  
to different points on the  
display  
12  
NTI CRYSTALMON TFT/LCD MONITOR  
SPECIFICATIONS  
LCD  
Display area………………………………..337.92mm (W)x270.336 (H) (17 inch diagonal)  
Panel Type…………………………………TFT Active  
Number of Pixels.....................................1280 (H)x1024 (V)  
Number of Colors ....................................16.2 Million (6 bits + FRC)  
Pixel Pitch................................................0.264(H)x0.264(V)  
Color Pixel Arrangement.........................RGB Vertical Stripe  
Brightness................................................300cd/m2 (Nits)  
Response Time .......................................5.5ms  
Viewing Angle..........................................Horizontal: 140º; Vertical: 130º (Typ.)  
Optimum Viewing Direction.....................6 o’clock  
Backlight Unit………………………………CCFL, 4 Tables, Edge-Light (2 Top/2 Bottom)  
Operating Lamp Life................................40,000-50,000 hrs  
Contrast Ratio……………………………..500:1  
Display Controller  
Connector…………………………………15HD, DVI-D, female  
Video Format...........................................VGA,SVGA, XGA, SXGA  
Signal Input (from Video Source)……….Analog RGB (15HD), Digital TMDS (DVI)  
Sync Range.............................................H: 31 ~ 80KHz, V: 55 ~ 76Hz  
OSD Control……………………………….Menu, Up, Down, Select, Power (5 keys)  
Plug and Play ..........................................VESA DDC 2B Ver1.3  
OSD Control Board  
OSD Control............................................5 Keys  
Power Key...............................................Power ON/OFF  
Menu Key ................................................Activates Menu  
Up, Down Keys........................................Navigation Control  
Select Key ...............................................Select (when in Menu); Auto Adjust (not in menu)  
LED..........................................................Indicates Operation Status  
..........................................................Green = Power-ON, Video Input OK  
..........................................................Red = Suspend / Stand-by, or Input Out of Range  
Enclosure  
Material....................................................Electro-galvanized steel black powdercoated  
CM-RK17 Dimensions (WxDxH)…….…. 19 x 3.7 x 12.25 (7RU)  
CM-WL17 Dimensions (WxDxH).............16.5 x 3.7 x 12.2  
CM-DT17 Dimensions (WxDxH) .............16.5 x 3.7 x 12.2  
General Specs  
Power Supply …………………………… .120 or 240VAC at 50 or 60 Hz-12VDC/5A via AC Adapter  
Operating Temperature...........................0-40˚C  
Weight………………………………………12 lbs  
Compliance Certifications  
CE Mark...................................................Complies with EN55022  
FCC .........................................................Part 15 (Class A Digital Device)  
13  
NTI CRYSTALMON TFT/LCD MONITOR  
DIMENSIONS  
16.5"  
3.7"  
12.2"  
SIDE VIEW  
FRONT VIEW  
CM-WL17  
(ALSO APPLIES TO CM-DT17 WITHOUT DESKTOP STAND SHOWN)  
14  
NTI CRYSTALMON TFT/LCD MONITOR  
3.7"  
19"  
12.25"  
SIDE VIEW  
FRONT VIEW  
CM-RK17  
TROUBLESHOOTING  
Problem  
Solution  
Power LED is OFF  
Power LED is red  
Check to see if AC adapter is fully inserted  
Check connections of video source cables  
Make sure video sources are switched ON  
Power LED is green, but there's no picture  
Check to see if Horizontal Sync is out of range. Also  
check brightness and contrast controls in OSD menu  
(see page 11)  
INDEX  
CE, i  
cleaning, 3  
Control buttons, 10  
Dimensions, 14  
Display functions, 10  
FCC, i  
mounting instruction, 6  
OSD Controls, 10  
OSD Menu-DVI, 11  
source button, 4  
Specifications, 13  
Troubleshooting, 15  
15  
NTI CRYSTALMON TFT/LCD MONITOR  
WARRANTY INFORMATION  
The warranty period on this product (parts and labor) is two (2) years from the date of purchase. Please contact Network  
Technologies Inc at (800) 742-8324 (800-RGB-TECH) or (330) 562-7070 or visit our website at http://www.networktechinc.com  
for information regarding repairs and/or returns. A return authorization number is required for all repairs/returns.  
MAN058 Rev. 12/5/2008  
16  

JVC AV 29Q317B AV 29RXP8 AV 29S357 AV 21Q317B AV 21R318 AV 21RXP8 AV 21S357 User Manual
JVC AV 20420 AV 20421 User Manual
KitchenAid KGCP467JSS04 User Manual
Kuppersbusch USA GKS 11742 0 35 F UL User Manual
Maretron FPM100 User Manual
MSi 865PEM2 User Manual
Philips 27MT5005D 27MT6005D 32MT5015D 32MT6015D User Manual
Philips 29PT8607 User Manual
Philips 170W4P User Manual
Philips BDL4225E User Manual