NI PCI-8252 Quick Start Guide
The NI PCI-8252 is a highly flexible IEEE 1394a interface device for PCI.
The following sections describe how to get started using the NI PCI-8252.
Installing the NI PCI-8252
The following section contains a list of necessary and optional items for
acquiring images with the NI PCI-8252. This section also explains how to
unpack, configure, and install the NI PCI-8252.
What You Need to Get Started
You need the following items to set up and use the NI PCI-8252:
❑ NI-IMAQ for IEEE 1394 Cameras Software Installation Guide
❑ NI-IMAQ for IEEE 1394 Cameras and documentation
Note PDFs of the NI-IMAQ for IEEE 1394 Cameras documentation are installed on your
computer at <NI-IMAQ for IEEE 1394>/docs where <NI-IMAQ for IEEE 1394>
is the location to which NI-IMAQ for IEEE 1394 Cameras is installed.
❑ Computer with at least one PCI slot running Windows 2000/XP
❑ IEEE 1394 Camera
❑ Optional software packages and documentation:
–
IMAQ Vision for LabVIEW, LabWindows™/CVI™, or
Measurement Studio (Visual Basic)
–
–
–
–
Vision Builder for Automated Inspection
LabVIEW
LabWindows/CVI
Measurement Studio
❑ IEEE 1394 cable
You must insulate signal connections for the maximum voltage for which
the device is rated. Do not exceed the maximum ratings for the device.
Remove power from signal lines before connection to or disconnection
from the device.
Caution National Instruments measurement products may be classified as either
Measurement Category I or II. Operate products at or below the Measurement Category
level specified in the hardware specifications.
Measurement Category1: Measurement circuits are subjected to working
voltages2 and transient stresses (overvoltage) from the circuit to which they
are connected during measurement or test. Measurement Category
establishes standardized impulse withstand voltage levels that commonly
occur in electrical distribution systems. The following is a description of
Measurement (Installation3) Categories:
•
Measurement Category I is for measurements performed on circuits
not directly connected to the electrical distribution system referred to
as MAINS4 voltage. This category is for measurements of voltages
from specially protected secondary circuits. Such voltage
measurements include signal levels, special equipment, limited-energy
parts of equipment, circuits powered by regulated low-voltage sources,
and electronics.
•
•
Measurement Category II is for measurements performed on circuits
directly connected to the electrical distribution system. This category
refers to local-level electrical distribution, such as that provided by a
standard wall outlet (e.g., 115 V for U.S. or 230 V for Europe).
Examples of Measurement Category II are measurements performed
on household appliances, portable tools, and similar products.
Measurement Category III is for measurements performed in the
building installation at the distribution level. This category refers to
measurements on hard-wired equipment such as equipment in fixed
installations, distribution boards, and circuit breakers. Other examples
are wiring, including cables, bus-bars, junction boxes, switches,
socket-outlets in the fixed installation, and stationary motors with
permanent connections to fixed installations.
1
2
3
4
Measurement Categories as defined in electrical safety standard IEC 61010-1.
Working voltage is the highest rms value of an AC or DC voltage that can occur across any particular insulation.
Measurement Category is also referred to as Installation Category.
MAINS is defined as the (hazardous live) electrical supply system to which equipment is designed to be connected for the
purpose of powering the equipment. Suitably rated measuring circuits may be connected to the MAINS for measuring
purposes.
© National Instruments Corporation
3
NI PCI-8252 Quick Start Guide
•
Measurement Category IV is for measurements performed at the
primary electrical supply installation (<1,000 V). Examples include
electricity meters and measurements on primary overcurrent
protection devices and on ripple control units.
Unpacking
The NI PCI-8252 ships in an antistatic package to prevent electrostatic
discharge from damaging device components. To avoid such damage in
handling the device, take the following precautions:
•
Ground yourself via a grounding strap or by holding a grounded object,
such as the computer chassis.
•
Touch the antistatic package to a metal part of the computer chassis
before removing the device from the package.
Caution Never touch the exposed pins of connectors.
Remove the device from the package and inspect it for loose components
or any other signs of damage. Notify National Instruments if the device
appears damaged in any way. Do not install a damaged device in the
computer.
Store the NI PCI-8252 in the antistatic package when not in use.
Installation
The following instructions are for general installation. Refer to the
documentation provided by your computer manufacturer for specific
instructions and warnings. Refer to the Specifications section for a list of
the typical power requirements for the device.
1. Install the NI-IMAQ for IEEE 1394 Cameras driver software before
installing the NI PCI-8252 device.
Note For information about how to install NI-IMAQ for IEEE 1394 Cameras, refer to the
NI-IMAQ for IEEE 1394 Cameras Software Installation Guide.
2. Power off and unplug the computer.
Caution To protect yourself and the computer from electrical hazards, the computer must
remain unplugged until the installation is complete.
3. Remove the computer cover to expose access to the expansion slots.
4. Choose an unused PCI slot, and remove the corresponding expansion
slot cover on the back panel of the computer.
NI PCI-8252 Quick Start Guide
4
ni.com
5. Touch a metal part on the computer case to discharge any static
electricity that might be on your clothes or body before handling
the NI PCI-8252. Static electricity can damage the device.
6. Remove the NI PCI-8252 from the antistatic package and gently rock
the NI PCI-8252 into the slot. The connection may be tight, but do not
force the device into place.
Note Check that the bracket of the NI PCI-8252 lines up with the hole in the back panel
rail of the computer chassis.
7. Unless your computer secures expansion devices in a different manner,
screw the mounting bracket of the device to the back panel rail of the
computer.
8. Replace the cover.
9. Plug in and power on the computer.
Your NI PCI-8252 is now installed.
Configuring the NI PCI-8252
After you have installed the NI PCI-8252 and powered on your computer,
Windows will recognize the device and assign resources to it. Use
Measurement & Automation Explorer (MAX), the National Instruments
configuration utility, to configure the IEEE 1394 camera connected to the
NI PCI-8252 for acquisition.
Note You must install NI-IMAQ for IEEE 1394 Cameras 2.0.1 or later before configuring
your camera in MAX. Refer to the NI-IMAQ for IEEE 1394 Cameras Software Installation
Guide for more information about how to configure your camera.
Specifications
These specifications are typical at 25 °C, unless otherwise stated.
Caution Misuse of this equipment may impair the protection features included.
Physical
Dimensions
PCI ......................................................... 6.40 × 12.16 cm (2.52 × 4.79 in.)
© National Instruments Corporation
5
NI PCI-8252 Quick Start Guide
Connector
1394 ........................................................Female, 6 pin (3)
PCI..........................................................32-bit, Universal
Signaling
PCI Vio ....................................................Universal, 33 MHz
1394 ........................................................IEEE 1394a-1995 S100, S200,
S400 transfer rates, OHCI v1.1
software interface. Actual 1394
transfer rates are system
dependent.
Power Consumption
Typical....................................................0 mA at 5 V = 0 mW
0 mA at 3.3 V = 0 mW
40 mA at 12 V = 480 mW (max)
Bus Power
1394 ........................................................12 V 10%, 12 W total,
up to 9.6 W/portwithATXpower
connected
Operating Environment
The NI PCI-8254 device is intended for indoor use only.
Ambient temperature range ....................0 °C to 55 °C
Operating relative humidity....................20% to 80%, noncondensing
Altitude ...................................................2,000 m (at 25 °C ambient
temperature)
Pollution Degree.....................................2
Measurement Category...........................I
Caution Do not use the NI PCI-8252 for connection to signals within Measurement
Categories II, III, or IV.
NI PCI-8252 Quick Start Guide
6
ni.com
Storage Environment
Ambient temperature range.................... –20 °C to 60 °C
Storage relative humidity....................... 20% to 95%, noncondensing
Safety
This product is designed to meet the requirements of the following
standards of safety for electrical equipment for measurement, control,
and laboratory use:
•
•
•
IEC 61010-1, EN 61010-1
UL 61010-1
CAN/CSA-C22.2 No. 61010-1
Note For UL and other safety certifications, refer to the product label, or visit
ni.com/certification, search by model number or product line, and click the
appropriate link in the Certification column.
Electromagnetic Compatibility
Emissions ............................................... EN 55011 Class A at 10 m
FCC Part 15A above 1 GHz
Immunity................................................ EN 61326:1997 + A2:2001,
Table 1
CE, C-Tick, and FCC Part 15 (Class A) Compliant
Note For EMC compliance, operate this device with shielded cabling.
CE Compliance
This product meets the essential requirements of applicable European
Directives, as amended for CE Marking, as follows:
Low-Voltage Directive (safety) ............. 73/23/EEC
Electromagnetic Compatibility
Directive (EMC) .................................... 89/336/EEC
Note Refer to the Declaration of Conformity (DoC) for this product for any additional
regulatory compliance information. To obtain the DoC for this product, visit
ni.com/certification, search by model number or product line, and click the
appropriate link in the Certification column.
© National Instruments Corporation
7
NI PCI-8252 Quick Start Guide
Where to Go for Support
The National Instruments Web site is your complete resource for technical
support. At ni.com/supportyou have access to everything from
troubleshooting and application development self-help resources to email
and phone assistance from NI Application Engineers.
A Declaration of Conformity (DoC) is our claim of compliance with the
Council of the European Communities using the manufacturer’s
declaration of conformity. This system affords the user protection for
electronic compatibility (EMC) and product safety. You can obtain the DoC
for your product by visiting ni.com/certification. If your product
supports calibration, you can obtain the calibration certificate for your
product at ni.com/calibration.
National Instruments corporate headquarters is located at
11500 North Mopac Expressway, Austin, Texas, 78759-3504.
National Instruments also has offices located around the world to help
address your support needs. For telephone support in the United States,
create your service request at ni.com/supportand follow the calling
instructions or dial 512 795 8248. For telephone support outside the United
States, contact your local branch office:
Australia 1800 300 800, Austria 43 0 662 45 79 90 0,
Belgium 32 0 2 757 00 20, Brazil 55 11 3262 3599,
Canada 800 433 3488, China 86 21 6555 7838,
Czech Republic 420 224 235 774, Denmark 45 45 76 26 00,
Finland 385 0 9 725 725 11, France 33 0 1 48 14 24 24,
Germany 49 0 89 741 31 30, India 91 80 51190000,
Israel 972 0 3 6393737, Italy 39 02 413091, Japan 81 3 5472 2970,
Korea 82 02 3451 3400, Lebanon 961 0 1 33 28 28,
Malaysia 1800 887710, Mexico 01 800 010 0793,
Netherlands 31 0 348 433 466, New Zealand 0800 553 322,
Norway 47 0 66 90 76 60, Poland 48 22 3390150,
Portugal 351 210 311 210, Russia 7 095 783 68 51,
Singapore 1800 226 5886, Slovenia 386 3 425 4200,
South Africa 27 0 11 805 8197, Spain 34 91 640 0085,
Sweden 46 0 8 587 895 00, Switzerland 41 56 200 51 51,
Taiwan 886 02 2377 2222, Thailand 662 278 6777,
United Kingdom 44 0 1635 523545
National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation.
Refer to the Terms of Use section on ni.com/legalfor more information about National
Instruments trademarks. Other product and company names mentioned herein are trademarks or trade
names of their respective companies. For patents covering National Instruments products, refer to the
appropriate location: Help»Patents in your software, the patents.txtfile on your CD, or
ni.com/patents.
© 2005 National Instruments Corporation. All rights reserved.
374130A-01
Jun05
|