NEC EA273WM User Manual

MultiSync EA243WM  
MultiSync EA273WM  
User’s Manual  
WARNING  
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT  
USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE  
PRONGS CAN BE FULLY INSERTED.  
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER  
SERVICING TO QUALIFIED SERVICE PERSONNEL.  
CAUTION  
CAUTION:  
TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED  
FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT  
THE POWER CORD FROM THE AC OUTLET.DO NOT REMOVE COVER (OR BACK). NO USER  
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause  
electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.  
This symbol alerts the user that important literature concerning the operation and maintenance of this unit  
has been included. Therefore, it should be read carefully in order to avoid any problems.  
CAUTION: Please use the power cord provided with this display in accordance with the table below. If a power cord is not  
supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the  
AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.  
European  
Continental  
Plug Type  
North America  
U.K.  
Chinese  
Japanese  
Plug Shape  
Country  
Voltage  
U.S.A./Canada  
120*  
EU (except U.K.)  
230  
U.K.  
230  
China  
220  
Japan  
100  
*When operating the monitor with its AC 125-240V power supply, use a power supply cord that matches the power supply  
voltage of the AC power outlet being used.  
NOTE:  
This product can only be serviced in the country where it was purchased.  
Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation.  
ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France, Germany, Italy,  
Norway, Spain, Sweden, U.K.  
ENERGY STAR is a U.S. registered trademark.  
All other brands and product names are trademarks or registered trademarks of their respective owners.  
®
As an ENERGY STAR Partner, NEC Display Solutions of America, Inc. has determined that this product  
meets the ENERGY STAR guidelines for energy efficiency. The ENERGY STAR emblem does not represent EPA  
endorsement of any product or service.  
The DisplayPort Icon is a trademark of the Video Electronics Standards Association, registered in the U.S.  
and other countries.  
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC  
in the United States and other countries.  
The intended primary use of this product is as an Information Technical Equipment in an office or domestic environment.  
The product is intended to be connected to a computer and is not intended for the display of television broadcast signals.  
English-1  
Registration Information  
Canadian Department of Communications Compliance Statement  
DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.  
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1.  
FCC Information  
1.  
Use the attached specified cables with the MultiSync EA243WM (L240UM)/MultiSync EA273WM (L270UL) monitor so as  
not to interfere with radio and television reception.  
(1)  
The power supply cord you use must have been approved by and comply with the safety standards of U.S.A.,  
and meet the following condition.  
Power supply cord  
Length  
Non shield type, 3-conductor  
1.8 m  
Plug shape  
U.S.A  
(2)  
Please use the supplied shielded video signal cable, 15-pin mini D-SUB to D-SUB cable or DVI-D to DVI-D cable.  
Use of other cables and adapters may cause interference with radio and television reception.  
2.  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of  
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used  
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to  
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try  
to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult your dealer or an experienced radio/TV technician for help.  
If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions.  
The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify  
and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office,  
Washington, D.C., 20402, Stock No. 004-000-00345-4.  
Declaration of Conformity  
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not  
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause  
undesired operation.  
U.S. Responsible Party: NEC Display Solutions of America, Inc.  
Address:  
500 Park Boulevard, Suite 1100  
Itasca, Illinois 60143  
(630) 467-3000  
Tel. No.:  
Type of Product:  
Display Monitor  
Equipment Classification: Class B Peripheral  
Model: MultiSync EA243WM (L240UM)  
MultiSync EA273WM (L270UL)  
We hereby declare that the equipment specified above conforms  
to the technical standards as specified in the FCC Rules.  
English-2  
Recommended use  
Safety Precautions and Maintenance  
FOR OPTIMUM PERFORMANCE, PLEASE NOTE  
THE FOLLOWING WHEN SETTING UP AND  
USING THE LCD COLOR MONITOR:  
DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose  
you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel.  
Do not spill any liquids into the cabinet or use your monitor near water.  
Do not insert objects of any kind into the cabinet slots, as they may touch dangerous voltage points, which can be harmful or  
fatal or may cause electric shock, fire or equipment failure.  
Do not place any heavy objects on the power cord. Damage to the cord may cause shock or fire.  
Do not place this product on a sloping or unstable cart, stand or table, as the monitor may fall, causing serious damage to  
the monitor.  
The power supply cord you use must have been approved by and comply with the safety standards of your country.  
(Type H05VV-F 3G 1mm2 should be used in Europe).  
In UK, use a BS-approved power cord with molded plug having a black (5A) fuse installed for use with this monitor.  
Do not place any objects onto the monitor and do not use the monitor outdoors.  
Do not bend power cord.  
Do not use monitor in high temperatured, humid, dusty, or oily areas.  
Do not cover vent on monitor.  
Vibration can damage the backlight. Do not install where the monitor will be exposed to continual vibration.  
If monitor or glass is broken, do not come in contact with the liquid crystal and handle with care.  
To prevent damage to the LCD monitor caused by tipping over due to earthquakes or other shocks, make sure to install the  
monitor in a stable location and take measures to prevent falling.  
Immediately turn off the power, unplug your monitor from the wall outlet and move to a safe location then refer servicing to  
qualified service personnel under the following conditions. If the monitor is used in this condition, the monitor may cause fall, fire  
and electric shock:  
If the monitor stand has been cracked or peeled.  
If the monitor has been wobbled.  
If the monitor has an unusual odor.  
When the power supply cord or plug is damaged.  
If liquid has been spilled, or objects have fallen into the monitor.  
If the monitor has been exposed to rain or water.  
If the monitor has been dropped or the cabinet damaged.  
If the monitor does not operate normally by following operating instructions.  
Allow adequate ventilation around the monitor so that heat can properly dissipate. Do not block ventilated  
openings or place the monitor near a radiator or other heat sources. Do not put anything on top of monitor.  
The power cable connector is the primary means of detaching the system from the power supply.  
The monitor should be installed close to a power outlet which is easily accessible.  
CAUTION  
Handle with care when transporting. Save packaging for transporting.  
Do not touch LCD panel surface while transporting, mounting and setting.  
Applying pressure on the LCD panel can cause serious damage.  
Image Persistence: Image persistence is when a residual or “ghost” image of a previous image remains visible on the screen.  
Unlike CRT monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a long period  
of time should be avoided.  
To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image  
was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.  
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular  
intervals whenever the screen is idle or turning off the monitor when not in use.  
English-3  
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN  
REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE  
FOLLOWING WHEN YOU POSITION THE MONITOR:  
For optimum performance, allow 20 minutes for the display to warm up.  
Adjust the monitor height so that the top of the screen is at or slightly below eye level.  
Your eyes should look slightly downward when viewing the middle of the screen.  
Position your monitor no closer than 40 cm (15.75 inches) and no further away than  
70 cm (27.56 inches) from your eyes. The optimal distance is 50 cm (19.69 inches).  
Rest your eyes periodically by focusing on an object at least 20 feet away. Blink often.  
Position the monitor at a 90° angle to windows and other light sources to minimize glare  
and reflections. Adjust the monitor tilt so that ceiling lights do not reflect on your screen.  
If reflected light makes it hard for you to see your screen, use an anti-glare filter.  
Clean the LCD monitor surface with a lint-free, non-abrasive cloth. Avoid using any  
cleaning solution or glass cleaner!  
Adjust the monitor’s brightness and contrast controls to enhance readability.  
Use a document holder placed close to the screen.  
Position whatever you are looking at most of the time (the screen or reference material) directly in front of you to minimize  
turning your head while you are typing.  
Avoid displaying fixed patterns on the monitor for long periods of time to avoid image persistence (after-image effects).  
Get regular eye checkups.  
Ergonomics  
To realize the maximum ergonomics benefits, we recommend the following:  
To avoid eye fatigue, adjust the brightness to a moderate setting. Place a sheet of white paper next to the LCD screen for  
luminance reference.  
Do not position the Contrast control to its maximum setting.  
Use the preset Size and Position controls with standard signals.  
Use the preset Color Setting.  
Use non-interlaced signals with a vertical refresh rate of 60 Hz.  
Do not use primary color blue on a dark background, as it is difficult to see and may produce eye fatigue due to insufficient  
contrast.  
Cleaning the LCD Panel  
When the LCD is dusty, please gently wipe with a soft cloth.  
Please do not rub the LCD panel with hard or coarse material.  
Please do not apply pressure to the LCD surface.  
Please do not use OA cleaner as it will cause deterioration or discoloration on the LCD surface.  
Cleaning the Cabinet  
Unplug the power supply  
Gently wipe the cabinet with a soft cloth  
To clean the cabinet, dampen the cloth with a neutral detergent and water, wipe the cabinet and follow with a dry cloth.  
NOTE:  
Many plastics are used on the surface of the cabinet. DO NOT clean with benzene, thinner, alkaline detergent,  
alcoholic system detergent, glass cleaner, wax, polish cleaner, soap powder, or insecticide. Do not touch rubber or  
vinyl to the cabinet for a long time. These types of fluids and fabrics can cause the paint to deteriorate, crack or peel.  
For more detailed information on setting up a healthy work environment, write to the American National Standard for Human  
Factors Engineering of Computer Workstations - ANSI/HFES 100-2007 - The Human Factors Society, Inc. P.O. Box 1369, Santa  
Monica, California 90406.  
English-4  
Contents  
Your new NEC monitor box* should contain the following:  
MultiSync monitor with tilt/swivel/pivot/height adjust stand  
Power Cord*1  
Video Signal Cable (DVI-D to DVI-D cable)  
Video Signal Cable (Mini D-SUB 15 pin to Mini D-SUB 15 pin)  
USB Cable  
Audio Cable (ø 3.5 stereo mini plug)  
ControlSync Cable (ø 2.5 stereo micro plug)  
Setup Manual  
Mini D-SUB 15 pin to  
Mini D-SUB 15 pin  
Power Cord*1  
Audio Cable  
ControlSync Cable  
Setup Manual  
USB Cable  
DVI-D to DVI-D cable  
*
*
Remember to save your original box and packing material to transport or ship the monitor.  
1
The type and number of power cords included will depend on the where the LCD monitor is to be shipped. When more than one power cord  
is included, please use the power cord that matches the AC voltage of the power outlet and has been approved by and complies with the  
safety standard of your particular country.  
English-5  
Quick Start  
To connect the LCD monitor to your system, follow these instructions:  
NOTE:  
Make sure to read “Recommended Use” (page 3) before installation.  
1. Turn off the power of your computer.  
2. For a PC or MAC with DVI digital output: Connect the DVI signal cable to the connector of the display card in your system  
(Figure A.1). Tighten all screws.  
For a PC with Analog output: Connect a 15-pin mini D-SUB signal cable to the connector of the display card in your  
system (Figure A.2).  
For a MAC: Connect a Macintosh cable adapter (not included) to the computer, then attach the 15-pin mini D-SUB signal  
cable to the Macintosh cable adapter (Figure A.3).  
NOTE:  
Some Macintosh systems do not require any Macintosh cable adapter.  
For a PC with DisplayPort output: Connect the DisplayPort cable to the connector of the display card in your system  
(Figure A.4).  
Macintosh Cable  
Figure A.2  
Adapter  
DisplayPort cable  
(not included)  
Figure A.3  
Figure A.4  
Figure A.1  
(not included)  
NOTE:  
1. Please use a DisplayPort cable with DisplayPort logo.  
2. When removing the DisplayPort cable, hold down the top button to release the lock.  
3. Place hands on each side of the monitor to tilt the LCD panel 30-degree angle and lift up to the highest position.  
4. Connect all cables to the appropriate connectors (Figure C.1). When using the USB cable, connect the B type connector  
to the USB upstream port on the right back side of the monitor and the A type connector to the downstream port on the  
computer (Figure C.1a). If using the cord from a USB device, plug into one of the downstream ports of the monitor.  
NOTE:  
Incorrect cable connections may cause abnormal operation, damage display quality/components of LCD module and/  
or shorten the module’s life.  
30° Tilt  
A Type  
A Type  
USB Downstream  
B Type  
Headphone  
Highest  
Stand  
Position  
B Type  
Figure C.1a  
Audio Input  
ControlSync IN/OUT*  
DVI  
HDMI  
USB Upstream  
USB Downstream  
D-SUB  
DisplayPort  
Power cord  
Figure C.1  
*: See page 23  
English-6  
5. To keep the cables neatly organized, place them into the cable management system that is built into the stand.  
Place the cables in the hooks firmly and evenly (Figure C.2 and Figure C.3).  
NOTE:  
Cable cover is not removable.  
6. Please check that you can still rotate, raise and lower the monitor screen after you have installed the cables.  
Power Cord  
DisplayPort Cable*  
D-SUB Cable  
DVI Cable  
HDMI Cable*  
Audio Cable  
ControlSync Cables  
USB Cables  
Power Cord  
DisplayPort Cable*  
D-SUB Cable  
DVI Cable  
HDMI Cable*  
Audio Cable  
ControlSync Cables  
USB Cables  
Figure C.2  
Figure C.3  
* Cable not included.  
7. Connect one end of the power cord to the AC inlet on the back of the monitor and the other end to the power outlet.  
NOTE: Please refer to Caution section of this manual for proper selection of AC power cord.  
8. Turn on the computer and the monitor by pressing the power key on the front bezel (Figure E.1).  
9. No Touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup. For further adjustments, use  
the following OSD controls:  
• Auto Contrast (Analog input only)  
• Auto Adjust (Analog input only)  
Refer to the Controls section of this User’s Manual for a full description of these OSD controls.  
NOTE:  
If you have any problems, please refer to the Troubleshooting section of this User’s Manual.  
Power Sign  
Figure E.1  
English-7  
Raise and Lower Monitor Screen  
The monitor may be raised or lowered in either portrait or landscape mode.  
To raise or lower screen, place a hand on each side of the monitor and lift or lower to the desired height (Figure RL.1).  
NOTE:  
Handle with care when raising or lowering the monitor screen.  
Figure RL.1  
Screen Rotation  
Before rotating, disconnect power cord and all cables, then the screen must be raised to the highest level and tilt to avoid  
knocking the screen on the desk or pinching your fingers.  
To raise the screen, place a hand on each side of the monitor and lift up to the highest position (Figure RL.1).  
To rotate screen, place a hand on each side of the monitor screen and turn clockwise from landscape to portrait or counter-  
clockwise from portrait to landscape (Figure R.1).  
To rotate OSD menu between landscape and portrait, refer to “Controls” section.  
Figure R.1  
Tilt and Swivel  
Grasp the top and bottom sides of the monitor screen with your hands and adjust the tilt and swivel as desired (Figure TS.1).  
Figure TS.1  
NOTE:  
Handle with care when tilting the monitor screen.  
English-8  
Flexible Arm Installation  
This LCD monitor is designed for use with a flexible arm.  
To prepare the monitor for alternate mounting purposes:  
Follow the instructions provided by the manufacturer of the display mount.  
To meet the safety requirements, the mounting stand must be able to support the weight of the monitor and be UL-certified.  
Remove Monitor Stand for Mounting  
To prepare the monitor for alternate mounting purposes:  
1. Disconnect all cables.  
2. Place a hand on each side of the monitor and lift up to the highest position.  
3. Place monitor face down on a non-abrasive surface (Figure S.1).  
NOTE:  
Handle with care when the monitor is facing down.  
Figure S.1  
4. Remove 2 bottom screws first: Move stand left and right to remove bottom 2 screws (Figure S.2, S.3).  
5. Remove 2 top screws.  
6. Remove the stand (Figure S.4).  
7. The monitor is now ready for mounting in an alternate manner.  
8. Connect the cables to the back of the monitor.  
NOTE:  
Handle with care when removing monitor stand.  
Figure S.2  
Figure S.3  
Figure S.4  
English-9  
Mount Flexible Arm  
This LCD monitor is designed for use with a flexible arm.  
1. Follow the instructions on how Remove Monitor Stand for Mounting to remove the stand.  
2. Use the 4 screws removed from the stand to attach the arm to the monitor (Figure F.1).  
Caution: Use ONLY the screws (4 pcs) that were removed from the stand to avoid damage to the monitor or stand. To meet  
the safety requirements, the monitor must be mounted to an arm which guaranties the necessary stability under  
consideration of the weight of the monitor. The LCD monitor should only be used with an approved arm  
(e.g. GS mark).  
Thickness of Bracket (Arm)  
2.0~3.2 mm  
Additional 4 VESA  
4 Screws (M4)  
(Max Depth: 8.5 mm)  
100 mm  
100 mm  
Weight of LCD assembly: 4.3 kg  
Figure F.1  
Additional 4 VESA holes are provided for those users needing a lower monitor head position than that is available from the  
monitor stand in shipping configuration. The monitor stand can be re-attached by using the 4 screws to the lower position VESA  
holes.  
NOTE:  
1. The monitor head tilt function may experience impaired operation when attached to the lower position VESA holes.  
2. The monitor head pivot function should not be used when attached to the lower position VESA holes.  
English-10  
Controls  
OSD (On-Screen Display) control keys on the front of the monitor function  
are as follows:  
To access OSD menu, touch any of the control keys.  
To change signal input, touch the SELECT key.  
NOTE:  
Exit OSD in order to change signal input.  
1 Ambibright Sensor  
Human Sensor  
Detects the level of ambient lighting, allowing the monitor to make adjustments to various  
settings resulting in a more comfortable viewing experience. Do not cover this sensor.  
2 LED  
Indicates that the power is on or off.  
Turns the monitor on and off.  
3 Power  
4 INPUT/SELECT  
Enters the OSD Control menu. Enters OSD sub menus.  
Changes the input source when not in the OSD Control menu.  
5 MENU/EXIT  
6 LEFT/RIGHT  
Accesses OSD menu. Exits the OSD sub menu. Exits OSD Control menu.  
Navigates to the left or right through the OSD Control menu.  
You can adjust the BRIGHTNESS directly while the OSD menu is off*.  
7 UP/DOWN  
Navigates up or down through the OSD Control menu.  
You can adjust the VOLUME directly when not in the OSD Control menu*.  
8 RESET/ECO  
Resets the OSD back to factory settings in the OSD control menu.  
Switches among ECO MODE settings.  
Activates Auto Adjust function if helded for 3 seconds while the OSD menu is off (Analog input  
only)*.  
* When Hot Key function is OFF, this function is disabled.  
ECO TOOLS  
BRIGHTNESS  
Adjusts the overall image and background screen brightness.  
If ECO MODE is set to 1 or 2, a bar for CARBON FOOTPRINT will appear.  
CONTRAST  
Adjusts the overall image and background screen brightness by input signal level.  
ECO MODE  
Decreases the amount of power consumption by reducing the brightness level.  
OFF: No function.  
1 (ENERGY STAR SETTING): Sets brightness variable range from 0% to 80% (EA243WM)/from 0% to 70%  
(EA273WM).  
This setting can adjust brightness to a range in which power is reduced to meet Energy Star measurement conditions.  
2 (40% POWER SAVINGS - EA243WM) (50% POWER SAVINGS - EA273WM): Sets brightness variable range from  
0% to 40%.  
This setting can adjust brightness to a range in which power is reduced by 40% (EA243WM)/50% (EA273WM)  
compared to the maximum brightness setting.  
When this function is set to ON, a CARBON FOOTPRINT bar will appear alongside the brightness adjustment bar.  
NOTE: This function is disabled when DV mode is set for Dynamic.  
English-11  
AUTO BRIGHTNESS  
OFF: No function.  
1 (AMBIENT LIGHT): Automatically adjusts the brightness to the optimal setting by detecting the brightness level of  
the environment*1.  
*1: Please refer to page 22 for full “Auto Brightness” information.  
2 (WHITE CONTENT): Automatically adjusts the brightness to the optimal brightness setting based on the white  
display area.  
The environmental brightness sensor (Ambibright sensor) has no function.  
3 (AMBIENT + CONTENT): Automatically adjusts the brightness to the optimal setting based on the white display area  
and the brightness level of the environment, detected by the AmbiBright sensor.  
NOTE: This function is disabled when DV mode is set for Dynamic.  
OFF MODE SETTING  
The Intelligent Power Manager allows the monitor to enter into power saving mode after a period of inactivity.  
The OFF MODE has two settings:  
STANDARD: Monitor enters into power saving mode automatically when the input signal is lost.  
SENSOR: Monitor enters into power saving mode automatically when the amount of surrounding light goes below the  
level determined by you. The level can be adjusted in OFF MODE sensor setting.  
When in power saving mode, the LED on the front of the monitor becomes dark blue. When in power saving mode,  
touch any of the front keys, except for POWER and INPUT, to return to normal.  
When the amount of surrounding light returns to normal levels, the monitor will automatically return to normal mode.  
SENSOR SETTING (OFF MODE SETTING)  
Adjusts threshold level of ambient light sensor for detected dark condition and shows current sensor measurement  
result.  
START TIME (OFF MODE SETTING)  
Adjusts wait time to enter into to a lower power consumption level when Ambient Sensor detects dark condition.  
HUMAN SENSING  
The sensor on the front side of the monitor detects the movement of a person by using the HUMAN SENSING  
function. THE HUMAN SENSING has three settings:  
OFF: No human sensing.  
1 (LIGHT): After it is detected that there is no person after a period of time, the monitor shifts to low brightness mode  
automatically to reduce the power consumption. When a person comes near the monitor again, the monitor will  
automatically return to normal mode. START TIME adjusts the wait time to react.  
2 (DEEP): After it is detected that there is no person, the monitor shifts to power saving mode automatically to reduce  
the power consumption. When a person comes near the monitor again, it resumes from the power saving mode and  
displays the images.  
SENSOR SETTING (HUMAN SENSING)  
Adjusts the threshold level of human sensing.  
When human icon is located on the right side of the white color bar or vermilion color wave, it is detected that there is  
no person.  
NOTE: Once the OSD has been closed, Human sensor starts to work.  
START TIME (HUMAN SENSING)  
Adjusts the wait time of entering to low brightness mode or power saving mode when Human Sensor detects no  
person.  
DV MODE  
Dynamic Visual Mode allows you to select from the following settings:  
STANDARD: Standard setting.  
TEXT: Setting that makes letters and lines crisp; best suited for basic word processing and spreadsheets.  
MOVIE: Setting that boosts dark tones; best suited for movies.  
GAMING: Setting that boosts whole tones; best suited for games that use vivid, colorful images.  
PHOTO: Setting that optimizes contrast; best suited for still images.  
DYNAMIC: Setting that adjusts the brightness by detecting the screen’s black areas and optimizes it.  
English-12  
SCREEN (Analog input only)  
AUTO ADJUST  
Automatically adjusts the image position, H. Size and Fine settings.  
AUTO CONTRAST  
Adjusts the image displayed for non-standard video inputs.  
LEFT / RIGHT  
Controls horizontal image position within the display area of the LCD.  
DOWN / UP  
Controls vertical image position within the display area of the LCD.  
H.SIZE  
Adjusts the horizontal size by increasing or decreasing this setting.  
If the “AUTO Adjust” function does not give you a satisfactory picture setting, a further tuning can be performed by  
using the “H.Size” function (dot clock). For this a Moiré test pattern could be used. This function may alter the width  
of the picture. Use LEFT/RIGHT key to center the image on the screen. If the H.Size is wrongly calibrated, the result  
would look like the left drawing. The image should be homogeneous.  
When H.SIZE value is  
wrong.  
When H.SIZE value is  
improved.  
When H.SIZE value is  
correct.  
FINE  
Improves focus, clarity and image stability by increasing or decreasing this setting.  
If the “Auto Adjust” function and the “H.Size” function do not give you a satisfactory picture setting, a fine tuning can be  
performed by using the “Fine” function.  
For this a Moiré test pattern could be used. If the Fine value is wrongly calibrated, the result would look like the left  
drawing. The image should be homogeneous.  
When FINE value is  
wrong.  
When FINE value is  
correct.  
INPUT RESOLUTION  
Selects one of the following pair of resolutions as the input signal priority:  
1360 x 768 or 1280 x 768 or 1024 x 768 (vertical resolution 768),  
1600 x 900 or 1280 x 960 (horizontal frequency 60kHz, vertical frequency 60Hz),  
1680 x 1050 or 1400 x 1050 (vertical resolution 1050).  
Color  
Color Control System: Six color presets select the desired color setting (sRGB and NATIVE color presets are  
standard and cannot be changed).  
1, 2, 3, 5: Increases or decreases Red, Green or Blue color depending upon which is selected. The change in color will  
appear on screen and the direction (increase or decrease) will be shown by the bars.  
NATIVE: Original color presented by the LCD panel that is unadjustable.  
sRGB: sRGB mode dramatically improves the color fidelity in the desktop environment by a single standard RGB color  
space. With this color-supported environment, the operator could easily and confidently communicate color without  
further color management overhead in most common situations.  
NOTE: When MOVIE, GAMING, or PHOTO is selected as the DV MODE, NATIVE is selected automatically as the six  
color preset and cannot be changed.  
English-13  
Tools  
VOLUME  
Controls the volume of the speakers or headphones.  
To mute the speaker output, touch the “RESET/ECO MODE” key.  
SOUND INPUT (HDMI, DisplayPort inputs only)  
This function selects Audio Input, HDMI or DisplayPort.  
VIDEO LEVEL (HDMI input only)  
NORMAL: Disables the expanded feature.  
EXPAND: Expands image contrast and increases details in the dark and bright areas.  
OVER SCAN (HDMI input only)  
Some video formats may require different scanning modes in order to best display the image.  
ON: Image size is larger than what can be displayed. The image edge will appear cropped. Approximately 95% of the  
image will be shown on the screen.  
OFF: Image size stays within the display area. The whole image is displayed on the screen.  
VIDEO DETECT  
Selects the method of video detection when more than one video inputs are connected.  
FIRST: When current video input signal is not present, then the monitor searches for a video signal from the other  
video input port. If the video signal is present in the other port, then the monitor switches the video source input port  
to the new found video source automatically. The monitor will not look for other video signals while the current video  
source is present.  
NONE: The monitor will not search the other video input port unless it is turned on.  
EXPANSION MODE  
Sets the zoom method.  
FULL: The image is expanded to full screen, regardless of the resolution.  
ASPECT: The image is expanded without changing the aspect ratio.  
Note (EA243WM only): The resolution of 1280x768, 1360x768, 1280x720, 1600x900 and 1920x1080 are always  
FULL.  
OFF TIMER  
Monitor will automatically power down when you have selected a pre-determined amount of time.  
Before powering off, a message will appear on the screen asking if you want to delay the turn off time by 60 minutes.  
Touch any OSD key to delay the power-down time.  
LED BRIGHTNESS  
You can adjust the blue LED brightness.  
DDC/CI  
This function allows the DDC/CI function ON or OFF.  
FACTORY PRESET  
Selecting Factory Preset allows you to reset all OSD control settings back to the factory settings. Individual settings  
can be reset by touching the ECO (RESET) Key.  
MENU Tools  
LANGUAGE  
OSD control menus are available in eight languages.  
OSD TURN OFF  
The OSD control menu will stay on as long as it is in use. You can select how long the monitor waits after the last touch  
of a key to shut off the OSD control menu. The preset choices are 10-120 seconds by 5-second increments.  
OSD LOCK OUT  
This control completely locks out the access to all OSD control functions except for Brightness, Contrast and Volume.  
To activate the OSD Lock Out function, enter the OSD menu, select OSD LOCK OUT, then press “SELECT” and  
RIGHT simultaneously. To deactivate, press “SELECT” and LEFT simultaneously.  
English-14  
HOT KEY  
When this function is activated, ECO Mode, BRIGHTNESS and VOLUME can be adjusted without entering the OSD  
menu by using the front keys.  
ON: The “ECO” touch key on the bezel is enabled and can toggle among ECO settings.  
The Left/Right key adjusts the brightness level.  
The Up/Down key adjusts the volume level.  
OFF: The HOT KEY function for “ECO”, “Left/Right” and “Up/Down” functions are disabled.  
SIGNAL INFORMATION  
If you select “ON”, monitor displays “VIDEO INPUT MENU” after changing the input.  
If you select “OFF”, monitor doesn’t display “VIDEO INPUT MENU” after changing the input.  
SENSOR INFORMATION  
If you select “ON”, monitor displays “HUMAN SENSOR ON” message. If you select “OFF”, monitor doesn’t display  
“HUMAN SENSOR ON” message.  
KEY GUIDE  
If you select “ON”, the Key Guide appears on screen when the OSD control menu is accessed. The Key Guide will  
rotate when the OSD control menu is rotated.  
DATA COPY  
To initiate data copy from the master monitor to the sub monitor(s), select “DATA COPY” and touch “SELECT”.  
A “PROCEEDING...” indicator will appear on the screen.  
NOTE: This function is only intended for the master monitor in ControlSync.  
All of the settings specified in the ControlSync chart (see page 23) will be copied from the master monitor to  
the sub monitor(s).  
CUSTOMIZE SETTING  
Store the current settings for easy recovery.  
To store current settings: Touch “SELECT”. After a warning message appears, touch “RESET”, current settings are  
stored.  
To restore settings: Hold “MENU” for 3 seconds or more while the OSD menu is off.  
ECO Information  
CARBON SAVINGS: Displays the estimated carbon savings information in kg.  
COST: Displays the electricity cost savings in balance.  
CARBON CONVERT SETTING: Adjusts the carbon footprint factor in the carbon saving calculation. This initial setting  
is based on the OECD (2008 Edition).  
CURRENCY SETTING: Displays electricity pricing in 6 currency units.  
CURRENCY CONVERT SETTING: Displays electricity savings in kW/hour (US Currency is default).  
NOTE: This model’s initial setting is “Currency = US$” and its Currency Convert setting = $0.11.  
This setting can be changed by using the ECO information menu.  
If you want to use the French setting, please refer to steps below:  
1. Touch the Menu key and select the ECO information menu using the “LEFT” or “RIGHT” key.  
2. Select Currency setting item by touching the “UP” or “DOWN” key.  
3. The French currency unit is Euro ( ). You can adjust currency setting to Euro icon ( ) from US dollar ($)  
by touching the “LEFT” or “RIGHT” key in Current setting item.  
4. Select Currency Convert Setting by touching the “UP” or “DOWN” key*.  
5. Adjust Currency Convert Setting by touching the “LEFT” or “RIGHT” key.  
* This initial Euro ( ) setting is Germany of OECD (2007 Edition).  
Please check receipt of French’s electricity prices or OECD data for French.  
French of OECD (2007 Edition) was 0.12.  
English-15  
Information  
Provides information about the current resolution display and technical data including the preset timing being used and  
the horizontal and vertical frequencies. Indicates the model and serial numbers of your monitor.  
OSD Warning  
OSD warning menus disappear when EXIT is selected.  
NO SIGNAL: This function gives a warning when there is no horizontal or vertical sync. After power is turned on or  
when there is a change of input signal, the No Signal window will appear.  
OUT OF RANGE: This function gives a recommendation of the optimized resolution and refresh rate. After the power  
is turned on or there is a change of input signal or if the video signal doesn’t have proper timing, the Out Of Range  
menu will appear.  
English-16  
Specifications - EA243WM  
Monitor Specifications  
MultiSync EA243WM  
Notes  
LCD Module  
Diagonal: 61.13 cm/24.1 inches  
Viewable Image Size: 61.13 cm/24.1 inches  
Native Resolution (Pixel Count): 1920 x 1200  
Active matrix; thin film transistor (TFT) liquid crystal  
display (LCD); 0.270 mm dot pitch; 250 cd/m2 white  
luminance; 1000:1 contrast ratio (typical), (25000:1  
Contrast ratio, Dynamic).  
Input Signal  
DisplayPort:  
DisplayPort Connector: Digital RGB  
DVI-D 24pin: Digital RGB  
DisplayPort Complies with Standard V1.1a,  
applicable to HDCP  
DVI:  
DVI (HDCP)  
VGA:  
15pin Mini D-sub: Analog RGB  
Sync  
0.7 Vp-p/75 ohm  
Separate sync.TTL level Positive/Negative  
Composite sync.TTL level Positive/Negative  
Sync on Green  
(Video 0.7 Vp-p and Sync Negative 0.3 Vp-p)  
HDMI:  
HDMI Connector: Digital YUV  
Digital RGB  
HDMI  
Display Colours  
16,777,216  
Depends on display card used.  
Synchronization Range  
Horizontal: 31.5 kHz to 77.0 kHz (Analog)  
31.5 kHz to 77.0 kHz (Digital)  
Vertical: 56 Hz to 60 Hz  
Automatically  
Automatically  
Automatically  
Viewing Angle  
Left/Right:  
Up/Down:  
85° (CR > 10)  
80° (CR > 10)  
Image Formation Time  
Resolutions Supported  
5 ms (Typ.)  
640 x 480*1 @ 60 Hz  
Some systems may not support all modes listed.  
800 x 600*1 @ 56 Hz to 60 Hz  
1024 x 768*1 @ 60 Hz  
1280 x 960*1 @ 60 Hz  
1280 x 1024*1 @ 60 Hz  
1400 x 1050*1 @ 60 Hz  
1440 x 900*1 @ 60 Hz  
1600 x 1200*1 @ 60 Hz  
1680 x 1050*1 @ 60 Hz  
1920 x 1200 @ 60 Hz...........................................NEC DISPLAY SOLUTIONS cites recommended.  
Active Display Area  
USB Hub  
Landscape: Horiz.: 518.4 mm/20.4 inches  
Vert.: 324.0 mm/12.8 inches  
Portrait: Horiz.: 324.0 mm/12.8 inches  
Vert.: 518.4 mm/20.4 inches  
I/F: USB Specification Revision 2.0  
Port: Upstream 1  
Downstream 4  
Load Current: Maximum 0.5A per port  
AUDIO  
AUDIO Input:  
STEREO Mini Jack: Analog Audio  
DisplayPort Connector: Digital Audio  
HDMI Connector: Digital Audio  
Stereo L/R 500mV rms 20 Kohm  
PCM 2ch 32, 44.1, 48 kHz (16/20/24bit)  
PCM 2ch 32, 44.1, 48 kHz (16/20/24bit)  
Headphone Output: STEREO Mini Jack:  
Headphone Impedance 32 Ohm  
Speakers  
Practical Audio Output: 1.0 W + 1.0 W  
ControlSync  
(available up to 5 sub monitors)  
IN: Stereo Micro jack 2.5 φ  
OUT: Stereo Micro jack 2.5 φ  
Power Supply  
AC 100-240 V ~ 50/60 Hz  
Current Rating  
Dimensions  
0.80 - 0.45 A (with USB and Audio)  
Landscape: 556.2 mm (W) x 408.9 - 538.9 mm (H) x 230.0 mm (D)  
21.9 inches (W) x 16.1 - 21.2 inches (H) x 9.1 inches (D)  
Portrait: 359.6 mm (W) x 572.6 - 637.2 mm (H) x 230.0 mm (D)  
14.2 inches (W) x 22.5 - 25.1 inches (H) x 9.1 inches (D)  
Height Adjustment: 130 mm / 5.1 inches (Landscape orientation)  
64.6 mm / 2.5 inches (Portrait orientation)  
Weight  
7.0 kg (15.4 lbs)/Without stand: 4.1 kg (9.0 lbs)  
Environmental Considerations  
Operating Temperature: 5°C to 35°C/41°F to 95°F  
Humidity: 30% to 80%  
Altitude: 0 to 6,562 Feet/0 to 2,000 m  
Storage Temperature: -10°C to 60°C/14°F to 140°F  
Humidity: 10% to 85%  
Altitude: 0 to 40,000 Feet/0 to 12,192 m  
*1 Interpolated Resolutions: When resolutions are shown that are lower than the pixel count of the LCD module, text may appear different. This is normal and  
necessary for all current flat panel technologies when displaying non-native resolutions full screen. In flat panel technologies, each dot on the screen is actually one  
pixel, so to expand resolutions to full screen, an interpolation of the resolution must be done.  
NOTE:  
Technical specifications are subject to change without notice.  
English-17  
Specifications - EA273WM  
Monitor Specifications  
MultiSync EA273WM  
Notes  
LCD Module  
Diagonal: 68.57 cm/27.0 inches  
Viewable Image Size: 68.57 cm/27.0 inches  
Native Resolution (Pixel Count): 1920 x 1080  
Active matrix; thin film transistor (TFT) liquid crystal  
display (LCD); 0.311 mm dot pitch; 300 cd/m2 white  
luminance; 1000:1 contrast ratio (typical), (25000:1  
Contrast ratio, Dynamic).  
Input Signal  
DisplayPort:  
DisplayPort Connector: Digital RGB  
DVI-D 24pin: Digital RGB  
DisplayPort Complies with Standard V1.1a,  
applicable to HDCP  
DVI:  
DVI (HDCP)  
VGA:  
15pin Mini D-sub: Analog RGB  
Sync  
0.7 Vp-p/75 ohm  
Separate sync.TTL level Positive/Negative  
Composite sync.TTL level Positive/Negative  
Sync on Green  
(Video 0.7 Vp-p and Sync Negative 0.3 Vp-p)  
HDMI:  
HDMI Connector: Digital YUV  
Digital RGB  
HDMI  
Display Colours  
16,777,216  
Depends on display card used.  
Synchronization Range  
Horizontal: 31.5 kHz to 83.0 kHz (Analog)  
31.5 kHz to 83.0 kHz (Digital)  
Vertical: 56 Hz to 75 Hz  
Automatically  
Automatically  
Automatically  
Viewing Angle  
Left/Right:  
Up/Down:  
80° (CR > 10)  
80° (CR > 10)  
Image Formation Time  
Resolutions Supported  
5 ms (Typ.)  
720 x 400*1: VGA text  
Some systems may not support all modes listed.  
640 x 480*1 @ 60 Hz to 75 Hz  
800 x 600*1 @ 56 Hz to 75 Hz  
832 x 624*1 @ 75 Hz  
1024 x 768*1 @ 60 Hz to 75 Hz  
1152 x 870*1 @ 75 Hz  
1280 x 1024*1 @ 60 Hz to 75 Hz  
1400 x 1050*1 @ 60 Hz  
1440 x 900*1 @ 60 Hz  
1920 x 1080 @ 60 Hz...........................................NEC DISPLAY SOLUTIONS cites recommended.  
Active Display Area  
USB Hub  
Landscape: Horiz.: 597.6 mm/23.5 inches  
Vert.: 336.2 mm/13.2 inches  
Portrait: Horiz.: 336.2 mm/13.2 inches  
Vert.: 597.6 mm/23.5 inches  
I/F: USB Specification Revision 2.0  
Port: Upstream 1  
Downstream 4  
Load Current: Maximum 0.5A per port  
AUDIO  
AUDIO Input:  
STEREO Mini Jack: Analog Audio  
DisplayPort Connector: Digital Audio  
HDMI Connector: Digital Audio  
Stereo L/R 500mV rms 20 Kohm  
PCM 2ch 32, 44.1, 48 kHz (16/20/24bit)  
PCM 2ch 32, 44.1, 48 kHz (16/20/24bit)  
Headphone Output: STEREO Mini Jack:  
Headphone Impedance 32 Ohm  
Speakers  
Practical Audio Output: 1.0 W + 1.0 W  
ControlSync  
(available up to 5 sub monitors)  
IN: Stereo Micro jack 2.5 φ  
OUT: Stereo Micro jack 2.5 φ  
Power Supply  
AC 100-240 V ~ 50/60 Hz  
Current Rating  
Dimensions  
0.95 - 0.50 A (with USB and Audio)  
Landscape: 631.4 mm (W) x 415.0 - 545.0 mm (H) x 230.0 mm (D)  
24.9 inches (W) x 16.3 - 21.5 inches (H) x 9.1 inches (D)  
Portrait: 371.8 mm (W) x 647.2 - 674.8 mm (H) x 230.0 mm (D)  
14.6 inches (W) x 25.5 - 26.6 inches (H) x 9.1 inches (D)  
Height Adjustment: 130 mm / 5.1 inches (Landscape orientation)  
27.6 mm / 1.1 inches (Portrait orientation)  
Weight  
7.2 kg (15.9 lbs)/Without stand: 4.3 kg (9.5 lbs)  
Environmental Considerations  
Operating Temperature: 5°C to 35°C/41°F to 95°F  
Humidity: 30% to 80%  
Altitude: 0 to 6,562 Feet/0 to 2,000 m  
Storage Temperature: -10°C to 60°C/14°F to 140°F  
Humidity: 10% to 85%  
Altitude: 0 to 40,000 Feet/0 to 12,192 m  
*1 Interpolated Resolutions: When resolutions are shown that are lower than the pixel count of the LCD module, text may appear different. This is normal and  
necessary for all current flat panel technologies when displaying non-native resolutions full screen. In flat panel technologies, each dot on the screen is actually one  
pixel, so to expand resolutions to full screen, an interpolation of the resolution must be done.  
NOTE:  
Technical specifications are subject to change without notice.  
English-18  
Features  
DisplayPort: DisplayPort is designed to be the future-ready and scalable solution for high performance digital display connectivity. It  
enables the highest resolutions, the fastest refresh rates and deepest color depths over standard cables.  
HDMI: HDMI is designed to be the future-ready, scalable solution for high performance digital display connectivity. It enables the highest  
resolutions, the fastest refresh rates and deepest color depths over standard cables, especially for consumer audio/video equipment.  
Color Control Systems: Allow you to adjust the colors on your screen and customize the color accuracy of your monitor to a variety of  
standards.  
OSD (On-Screen Display) Controls: Allow you to quickly and easily adjust all elements of your screen image via simple to use on-  
screen menus.  
ErgoDesign Features: Enhanced human ergonomics to improve the working environment, protect the health of the user and save  
money. Examples include OSD controls for quick and easy image adjustments, tilt base for preferred angle of vision, small footprint and  
compliance with MPRII and TCO guidelines for lower emissions.  
Plug and Play: The Microsoft® solution with the Windows® operating system facilitates setup and installation by allowing the monitor  
to send its capabilities (such as screen size and resolutions supported) directly to your computer, automatically optimizing display  
performance.  
Intelligent Power Manager System: Provides innovative power-saving methods that allow the monitor to shift to a lower power  
consumption level when on but not in use, saving two-thirds of your monitor energy costs, reducing emissions and lowering the air  
conditioning costs of the workplace.  
Multiple Frequency Technology: Automatically adjusts monitor to the display card’s scanning frequency, thus displaying the resolution  
required.  
FullScan Capability: Allows you to use the entire screen area in most resolutions, significantly expanding image size.  
VESA Standard Mounting Interface: Allows users to connect your MultiSync monitor to any VESA standard third party mounting arm  
or bracket.  
No-Touch Auto Adjust (Analog input only): Automatically adjusts the monitor to optimal settings upon initial setup.  
sRGB Color Control: A new optimized color management standard which allows for color matching on computer displays and other  
peripherals. The sRGB, which is based on the calibrated color space, allows for optimal color representation and backward compatibility  
with other common color standards.  
Adjustable stand with pivot capability: Adds flexibility to your viewing preferences.  
USB 2.0 hub adds excitement to your computing by connecting you to digital cameras, scanners and more.  
Human Sensor: Shifts to a lower power consumption level when a person leaves the monitor, saving your monitor energy costs.  
NaViSet Software offers an expanded and intuitive graphical interface, allowing you to more easily adjust OSD display settings via  
mouse and keyboard.  
Environmental Impact (EA243WM): Annual typical maximum operating carbon footprint of this monitor (world-wide average) is  
approximately 41.8 kg (calculated by: rated wattage x 8 hours per day x 5 days a week x 45 weeks per year x Power-to-Carbon  
conversion factor - conversion factor is based on OECD publication of global CO2 emissions 2008 Edition). This monitor has a  
manufacturing carbon footprint of approximately 39.56 kg.  
Note: The manufacturing and operating carbon footprints are calculated by a unique algorithm developed exclusively by NEC for its  
monitors.  
Environmental Impact (EA273WM): Annual typical maximum operating carbon footprint of this monitor (world-wide average) is  
approximately 51.8 kg (calculated by: rated wattage x 8 hours per day x 5 days a week x 45 weeks per year x Power-to-Carbon  
conversion factor - conversion factor is based on OECD publication of global CO2 emissions 2008 Edition). This monitor has a  
manufacturing carbon footprint of approximately 41.34 kg.  
Note: The manufacturing and operating carbon footprints are calculated by a unique algorithm developed exclusively by NEC for its  
monitors.  
HDCP (High-bandwidth Digital Content Protection): HDCP is a system for preventing illegal copying of video data sent over a Digital  
Visual Interface (DVI). If you are unable to view material via the DVI input, this does not necessarily mean the display is not functioning  
properly. With the implementation of HDCP, there may be cases in which certain content is protected with HDCP and might not be  
displayed due to the decision/intention of the HDCP community (Digital Content Protection, LLC).  
ControlSync: Follow the steps of “DATA COPY” and copy the settings from the master monitor to the sub monitors by connecting  
the ControlSync cable. When the setting of the master monitor is adjusted, it is sent to the sub monitors automatically, providing easy  
setting controls in a multiple monitor environment.  
Customize Setting: Allows to store the current settings and recover stored settings.  
English-19  
Troubleshooting  
No picture  
The signal cable should be completely connected to the display card/computer.  
The display card should be completely seated in its slot.  
The monitor does not support DisplayPort converter signal.  
Front Power Switch and computer power switch should be in the ON position.  
Check to make sure that a supported mode has been selected on the display card or system being used.  
(Please consult display card or system manual to change graphics mode.)  
Check the monitor and your display card with respect to compatibility and recommended settings.  
Check the signal cable connector for bent or pushed-in pins.  
Check the signal input, “DVI-D”, “DisplayPort”, “HDMI” or “D-Sub”.  
If the front LED is dark blue, check the status of the OFF MODE SETTING mode (see page 12) or Human sensor (see  
page 12).  
When using an HDMI input, please change “OVER SCAN”.  
Power Key does not respond  
Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor.  
When something is stuck on the bezel, key becomes unresponsive.  
Image Persistence  
Image persistence is when a residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT  
monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a long period  
of time should be avoided. To alleviate image persistence, turn off the monitor for as long as the previous image was  
displayed. For example, if an image was on the monitor for one hour and a residual image remains, the monitor should  
be turned off for one hour to erase the image.  
NOTE:  
As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a moving screen saver at  
regular intervals whenever the screen is idle or turning off the monitor when not in use.  
Message “OUT OF RANGE” is displayed (screen is either blank or shows rough images only)  
Image is displayed only roughly (pixels are missing) and OSD warning “OUT OF RANGE” is displayed: Either signal  
clock or resolution is too high. Choose one of the supported modes.  
OSD warning “OUT OF RANGE” is displayed on a blank screen: Signal frequency is out of range. Choose one of the  
supported modes.  
Image is unstable, unfocused or swimming is apparent  
Signal cable should be completely attached to the computer.  
Use the OSD Image Adjust controls to focus and adjust display by increasing or decreasing the fine adjustment.  
When the display mode is changed, the OSD Image Adjust settings may need to be readjusted.  
Check the monitor and your display card with respect to compatibility and recommended signal timings.  
If your text is garbled, change the video mode to non-interlace and use 60Hz refresh rate.  
LED on monitor is not lit (no blue or amber color can be seen)  
Power Switch should be in the ON position and power cord should be connected.  
Increase LED BRIGHTNESS adjustment.  
Picture is not as bright  
Make sure ECO MODE and AUTO BRIGHTNESS are turned off.  
If the brightness fluctuates make sure AUTO BRIGHTNESS is turned off.  
Signal cable should be completely attached.  
LCD brightness degradation occurs due to long-term usage or extreme cold conditions.  
When using an HDMI input, please change “VIDEO LEVEL”.  
Display image is not sized properly  
Use the OSD Image Adjust controls to increase or decrease the Coarse adjustment.  
Check to make sure that a supported mode has been selected on the display card or system being used.  
(Please consult display card or system manual to change graphics mode.)  
When using an HDMI input, please change “OVER SCAN”.  
No Video  
If no video is present on the screen, turn the Power button off and on again.  
Make certain the computer is not in a power-saving mode (touch the keyboard or mouse).  
Some video cards do not output video signal when monitor is turned OFF/ON or disconnect/connect from the AC power  
cord under low resolution with DisplayPort.  
When using an HDMI input, please change “OVER SCAN”.  
English-20  
No Sound  
Make sure the speaker cable is proper connected.  
Check to see if mute is activated.  
Check the volume in the OSD menu.  
Check selected OSD’s Tools to “SOUND INPUT”, when DisplayPort or HDMI is in use.  
Brightness variations over time  
Change Auto Brightness to OFF and adjust brightness.  
NOTE:  
When Auto Brightness is set to ON, the monitor automatically adjusts brightness based on the environment.  
When the brightness of surrounding environment changes, the monitor will also change.  
USB Hub does not operate  
Check to make sure the USB cord is properly connected. Refer to your USB devise User’s Manual.  
Human sensor does not work  
If human icon on SENSOR SETTING (HUMAN SENSING) is located on vermilion color, it is detected that there is  
person.  
Make sure there is no object in front of Human sensor.  
Make sure there is no equipment which radiating infrared rays in front of monitor.  
ControlSync does not work  
Check to make sure that ControlSync cable is connected correctly.  
Check to make sure that ControlSync cable is not in “loop” connection.  
Master monitor should be connected OUT connector only.  
Please use provided ControlSync cable.  
You can use up to 5 sub monitors via ControlSync.  
English-21  
Using the Auto Brightness function  
The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the  
room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim accordingly.  
The purpose of this function is to make the viewing experience more comfortable to the eye in a variety of lighting conditions.  
The Auto Brightness function is set to 1 by default.  
SETUP  
Use the following procedures to select the Brightness Range that the monitor will use when the Auto Brightness function is  
activated.  
1. Set the BRIGHTNESS level. This is the brightness level that the monitor will go up to when the ambient light level is highest.  
Select this setting when the room is at its brightest.  
Select “1” or “3” in the AUTO BRIGHTNESS menu (Figure 1). Then use the front Keys to move the cursor up to the  
BRIGHTNESS setting. Choose the desired brightness level (Figure 2).  
Figure 1  
Figure 2  
2. Set the DARK level. This is the level of brightness that the monitor will go down to when the ambient light level is low.  
Make sure the room is at its darkest when setting this level.  
Then use the front Keys to move the cursor up to the BRIGHTNESS setting. Choose the desired brightness level (Figure 3).  
Figure 3  
When the “Auto Brightness” function is enabled the Brightness level of the screen changes automatically according to the  
lighting conditions of the room (Figure 4).  
BRIGHTNESS range  
BRIGHTNESS level set  
for the monitor to use  
when ambient lighting  
level is low.  
BRIGHTNESS level set for the  
monitor to use when ambient  
lighting level is high.  
Bright condition area  
room bright condition  
dark  
bright  
Dark condition area  
Screen Brightness value by Auto Brightness function  
Figure 4  
Lb: Border between bright and dim lighting conditions; set at factory  
L1: BRIGHTNESS level set for the monitor to use when ambient lighting level is high (L1>Lb)  
L2 : BRIGHTNESS level set for the monitor to use when ambient lighting level is low (L2<Lb)  
L1 and L2 are the brightness levels set by the user to compensate for changes in ambient lighting.  
English-22  
ControlSync  
1. Connect the master monitor with a sub monitor via a ControlSync cable (ø 2.5) into ControlSync IN/OUT.  
2. Follow the steps of DATA COPY. When the setting of the master monitor is adjusted, it will be copied and sent to the  
connected sub monitor(s) automatically.  
3. Up to 5 sub monitors can be daisy-chained via ControlSync.  
NOTE:  
Connect the master monitor via ControlSync OUT connector.  
The ControlSync icon will appear on the upper left of the OSD menu in the sub monitor.  
Do not connect IN-IN or OUT-OUT.  
ControlSync icon  
Do not make “loop” connection.  
Once the monitors are connected, turn the master monitor’s power button off and on  
to check if ControlSync operates correctly.  
Master Monitor  
Sub Monitor 1  
Sub Monitor 2  
OUT (Black)  
IN (Gray)  
IN OUT  
IN OUT  
Up to 5 sub monitors  
Next monitor  
(Black)  
(Gray)  
(Black)  
(Gray)  
ControlSync cable  
ControlSync cable  
The following settings can be controlled by ControlSync:  
ECO TOOLS  
BRIGHTNESS*  
CONTRAST  
Yes  
No  
TOOLS (continuation)  
VIDEO LEVEL  
No  
No  
OVER SCAN  
VIDEO DETECT  
EXPANSION MODE  
OFF TIMER  
ECO MODE  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
No  
No  
AUTO BRIGHTNESS  
OFF MODE SETTING  
OFF MODE SENSOR SETTING  
OFF MODE START TIME  
HUMAN SENSING  
HUMAN SENSOR SETTING  
HUMAN SENSOR START TIME  
DV MODE  
Yes  
Yes  
Yes  
Yes  
No  
LED BRIGHTNESS  
DDC/CI  
FACTORY PRESET  
LANGUAGE  
MENU TOOLS  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
No  
OSD TURN OFF  
OSD LOCK OUT  
HOT KEY  
SCREEN  
AUTO ADJUST  
AUTO CONTRAST  
LEFT/RIGHT  
No  
SIGNAL INFORMATION  
SENSOR INFORMATION  
KEY GUIDE  
No  
DOWN/UP  
No  
H.SIZE  
No  
CUSTOMIZE SETTING  
CARBON SAVINGS  
COST  
FINE  
No  
ECO INFORMATION  
No  
INPUT RESOLUTION  
Color preset  
No  
No  
COLOR  
TOOLS  
Yes  
No  
CARBON CONVERT SETTING  
CURRENCY SETTING  
Yes  
Yes  
R, G, B, color gain  
VOLUME  
Yes  
No  
CURRENCY CONVERT  
SETTING  
Yes  
SOUND INPUT  
Other settings:  
Power Control (DC switch)  
Ambient Sensor  
Human Sensor Result  
Audio Mute  
NOTE:  
Only the master monitor’s human sensor and ambient sensor are active. Please do not cover these sensors.  
Turn the monitor’s power off before connecting/disconnecting the ControlSync cable.  
Do not use the ControlSync connectors for any purpose other than specified.  
* This value is not a directly adjusted output value. This is adjusted relatively.  
English-23  
TCO Displays 5  
Congratulations!  
This display is designed for both you and the planet!  
The display you have just purchased carries the TCO  
CertiÞed label. This ensures that your display is designed,  
manufactured and tested according to some of the strictest  
quality and environmental requirements in the world.  
This makes for a high performance product, designed with  
the user in focus that also minimizes the impact on the  
climate and our natural environment.  
TCO CertiÞed is a third party veriÞed program, where every product model is tested by an  
accredited impartial test laboratory. TCO CertiÞed represents one of the toughest certiÞcations  
for displays worldwide.  
Some of the Usability features of the TCO Certified for displays:  
• Good visual ergonomics and image quality is tested to ensure top performance and reduce  
sight and strain problems. Important parameters are luminance, contrast, resolution, black level,  
gamma curve, color and luminance uniformity, color rendition and image stability.  
• Product have been tested according to rigorous safety standards at an impartial laboratory.  
• Electric and magnetic Þelds emissions as low as normal household background levels.  
• Low acoustic noise emissions.  
Some of the Environmental features of the TCO Certified for displays:  
• The brand owner demonstrates corporate social responsibility and has a certiÞed  
environmental management system (EMAS or ISO 14001).  
Very low energy consumption both in on- and standby mode minimize climate impact.  
• Restrictions on chlorinated and brominated ßame retardants, plasticizers, plastics and  
heavy metals such as cadmium, mercury and lead (RoHS compliance).  
• Both product and product packaging is prepared for recycling.  
• The brand owner offers take-back options.  
The requirements can be downloaded from our web site. The requirements included in this  
label have been developed by TCO Development in co-operation with scientists, experts,  
users as well as manufacturers all over the world. Since the end of the 1980s TCO has been  
involved in inßuencing the development of IT equipment in a more user-friendly direction.  
Our labeling system started with displays in 1992 and is now requested by users and IT-  
manufacturers all over the world. About 50% of all displays worldwide are TCO certiÞed.  
For more information, please visit  
English-24  
Manufacturer’s Recycling and Energy Information  
NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s  
top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally-  
friendly products, and always strive to help define and comply with the latest independent standards from agencies such as  
ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).  
Disposing of your old NEC product  
The aim of recycling is to gain an environmental benefit by means of re-use, upgrading, reconditioning or reclamation of  
material. Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely  
disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures  
and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life.  
All required information concerning the disposal of the product and country-specific information on recycling facilities can be  
found on our following websites:  
Energy Saving  
This monitor features an advanced energy saving capability. When a VESA Display Power Management Signalling (DPMS)  
Standard signal is sent to the monitor, the Energy Saving mode is activated. The monitor enters a single Energy Saving mode.  
Mode  
Power consumption  
LED colour  
46 W (EA243WM)  
57 W (EA273WM)  
Maximum Operation  
Blue  
20 W Default setting (EA243WM), USB/Audio sleeping  
26 W Default setting (EA273WM), USB/Audio sleeping  
Normal Operation (at TCO testing)  
Blue  
Energy Saving Mode  
Off Mode  
0.48 W  
0.41 W  
Amber  
Unlit  
WEEE Mark (European Directive 2002/96/EC)  
Within the European Union  
EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic  
products carrying the mark (left) must be disposed of separately from normal household waste. This includes  
monitors and electrical accessories, such as signal cables or power cords. When you need to dispose of your  
NEC display products, please follow the guidance of your local authority, or ask the shop where you purchased  
the product, or if applicable, follow any agreements made between yourself and NEC.  
The mark on electrical and electronic products only applies to the current European Union Member States.  
Outside the European Union  
If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority  
so as to comply with the correct disposal method.  
English-25  

HP Hewlett Packard v216 User Manual
Intel Computer Hardware PCM 6892 Rev B User Manual
Intel LGA775 CORE MI940 User Manual
Intel MB935 User Manual
JVC DIGIPURE HV L29PRO User Manual
KitchenAid YKECC502G User Manual
Konftel Conference Phone 300 User Manual
NEC PD78P214 User Manual
Panasonic TX 66PW150A User Manual
Philips 70KV5757 User Manual