Motorola MVME5100 Series User Manual

M V M E 5 1 0 0 S e r i e s

V M E P r o c e s s o r M o d u l e s

™

♦ PowerPC 7400 or PowerPC 750

microprocessor with 32KB/32KB L1 cache

♦ Up to 2MB of secondary backside cache

♦ 100 MHz front-side bus

♦ 64MB, 128MB, or 512MB of on-board

ECC SDRAM—expandable up to 1GB

with optional RAM500 memory expansion

modules

♦ Up to 17MB Flash memory

♦ Dual IEEE P1386.1 compatible 32/64-bit

PMC expansion slots

♦ 64-bit PCI expansion mezzanine

connector allowing up to four more PMCs

♦ Dual 16550 compatible async serial ports

♦ Dual 10BaseT/100BaseTX Ethernet

♦ 32KB NVRAM and time-of-day clock with

replaceable battery backup

♦ Four 32-bit timers, one watchdog timer

♦ On-board debug monitor

♦ Single VME slot even when fully

configured with two PMC modules and

both add-on memory mezzanines

Supercomputing levels of performance in a scalable, single-board

computer

The MVME5100 is a high-performance VME processor module featuring the

Motorola Computer Group (MCG) PowerPlus II architecture with a choice of

™

PowerPC processors—either Motorola’s MPC7400 with AltiVec technol-

ogy for algorithmic-intensive computations or the low-power MPC750.

Based on an integrated PCI bridge–memory controller ASIC designed by

MCG, PowerPlus II takes memory performance to new levels with 582MB/s

memory read bandwidth and 640MB/s burst write bandwidth. Plus, Power-

Plus II architecture supports full PCI throughput of 264MB/s without starving

the CPU from its memory.

The MVME5100 is designed to meet the needs of OEMs servicing the military

and aerospace, industrial automation, and semiconductor process equipment

market segments.

face signals to the MVME712M transition module. The 3-row

P2 adapter can be used for 8-bit SCSI.

Flash Memory

Type:

EEPROM, on-board programmable

Capacity:

1MB via two 32-pin PLCC/CLCC sockets;

16MB surface mount

To gain access to the additional user definable I/O pins pro-

vided via the 5-row VME64 extension connector, a special P2

adapter board is available. This adapter panel replaces the

traditional 3-row P2 adapter and extends its capability by pro-

viding access to the PMC I/O pins.

Read Access (16MB

port):

70 clocks (32-byte burst)

Read Access (1MB

port):

262 clocks (32-byte burst)

NVRAM

S o f t w a r e S u p p o r t

Capacity:

Cell Storage Life:

Cell Capacity Life:

Removable Battery:

32KB (4KB available for users)

50 years at 55° C

S o f t w a r e S u p p o r t

5 years at 100% duty cycle, 25° C

Yes

Firmware Monitor

Firmware must fulfill the traditional functions of test and initial-

ization and provide operating system boot support. The

MVME5100 firmware monitor exceeds these requirements

with a proven monitor from the embedded VME leader. It

expands features like power-up tests with extensive diagnos-

tics, as well as a powerful evaluation and debug tool for sim-

ple checkout or when high-level development debuggers

require additional support. All this is included with the

MVME5100 firmware; plus it supports booting both operating

systems and kernels.

Counters/Timers

TOD Clock Device:

M48T37V

Real-Time Timers/

Counters:

Four, 32-bit programmable

Watchdog Timer:

Time-out generates reset

VMEbus ANSI/VITA 1-1994 VME64 (IEEE STD 1014)

Controller:

DTB Master:

DTB Slave:

Arbiter:

Tundra Universe

A16–A32; D08–D64, BLT

A24–A32; D08–D64, BLT, UAT

RR/PRI

Operating Systems and Kernels

MVME5100 supports booting a variety of operating systems

including a complete range of real-time operating systems

and kernels which may be purchased from the following com-

Interrupt Handler/

Generator:

IRQ 1–7/Any one of seven IRQs

System Controller:

Location Monitor:

Yes, jumperable or auto detect

Two, LMA32

panies:

Wind River Systems, Inc.:

Multiple Partners:

VxWorks

Ethernet Interface

Controller:

Linux

Two Intel 82559ER

10/100Mb/s

Interface Speed:

PCI Local bus DMA:

Connector:

S p e c i f i c a t i o n s

Yes, with PCI burst

S p e c i f i c a t i o n s

One routed to front panel RJ-45, one

routed to front panel RJ-45 or optionally

routed to P2, RJ-45 on MVME761

M V M E 5 1 0 0 P r o c e s s o r M o d u l e

MVME5100 Processor Module

Asynchronous Serial Ports

Controller:

Processor

16C550C UART

Microprocessor:

MPC7400

400 MHz

MPC750

450 MHz

32K/32K

1MB

Number of Ports:

Configuration:

Two, 16550 compatible

EIA-574 DTE

Clock Frequency:

On-chip Cache (I/D):

Secondary Cache:

32K/32K

Async Baud Rate, bps

max.:

38.4K EIA-232, 115Kbps raw

1MB or 2MB

Connector:

One routed to front panel RJ-45, one on

planar for development use

Main Memory

Type:

PC100 ECC SDRAM with 100 MHz bus

Dual IEEE P1386.1 PCI Mezzanine Card Slots

Capacity:

64MB, 128MB, or 512MB on board,

expandable to 1GB with RAM500 mem-

ory mezzanines

Address/Data:

A32/D32/D64, PMC PN1, PN2, PN3,

PN4 connectors

PCI Bus Clock:

Signaling:

Power:

33 MHz

Single Cycle Accesses:

Read Burst Mode:

Write Burst Mode:

Architecture:

10 Read/5 Write

7-1-1-1 idle; 2-1-1-1 aligned page hit

4-1-1-1 idle; 2-1-1-1 aligned page hit

64-bit, single interleave

+3.3V, +5V, ±12V; 7.5 watts maximum

per PMC slot

Module Types:

Two single-wide or one double-wide, front

panel or P2 I/O

PCI Expansion Connector

Parallel Port

Address/Data:

PCI Bus Clock:

Signaling:

Controller:

A32/D32/D64

33 MHz

PC97307

Configuration:

8-bit bi-directional, full IEEE 1284 sup-

port; Centronics compatible (minus EPP

and ECP on MVME712M)

Connector:

114-pin connector located on the planar

of the MVME5100

Modes:

Master only

Power Requirements

(additional power load placed on MVME5100 with IPMC installed)

Power Requirements

(not including power required by PMC or IMPC modules)

IPMC761

IPMC712

+5V ± 5%

+12V ± 10%

8.0 mA typ.

–12V ± 10%

2.0 mA typ.

+5V:

0.5 A max.

0.75 A max.

0.5 A max.

0.75 A max.

MVME5100:

3.0 A typ.

+3.3V

MVME5100 with

MVME761:

3.2 A typ.,

4.0 A max.

0.2 A typ.

0.5 A max.

0.1 A typ.

0.3 A max.

T r a n s i t i o n M o d u l e s

Board Size

Transition Modules

Height:

Depth:

233.4 mm (9.2 in.)

I/O Connectors

160.0 mm (6.3 in.)

261.8 mm (10.3 in.)

19.8 mm (0.8 in.)

14.8 mm (0.58 in.)

MVME761

MVME712M

Front Panel Height:

Width:

Asynchronous

Serial Ports:

Two, DB-9 labeled as

COM1 and COM2

Three, DB-25 labeled

as Serial 1, Serial 2,

and Serial 3

Max. Component

Height:

Synchronous

Serial Ports:

Two HD-26 labeled as One, DB-25 labeled as

I P M C M o d u l e s

Serial 3 and Serial 4

(user configurable via

installation of SIMs),

Two 60-pin connectors

on MVME761 planar

for installation of two

SIMs

Serial 4

IPMC Modules

PMC Interface

Address/Data:

A32/D32/D64, PMC PN1, PN2, PN3,

PN4 connectors

PCI Bus Clock:

Signaling:

33 MHz

Parallel Port:

Ethernet:

SCSI:

HD-36, Centronics

compatible

D-36, Centronics com-

patible

Module Type:

Basic, single-wide; P2 I/O

10BaseT or

100BaseTX, RJ-45

not available

SCSI Bus

8- or 16-bit, 50- or 68-

pin connector via P2

adapter

8-bit, standard SCSI D-

Controller:

Symbios 53C895A

Yes, with PCI local bus burst

5.0MB/s

PCI Local Bus DMA:

Asynchronous (8-bit

mode):

Board Size

Height:

233.4 mm (9.2 in.)

80.0 mm (3.1 in.)

Ultra SCSI:

20.0MB/s (8-bit mode), 40.0MB/s (16-bit

mode)

Depth:

Front Panel Height:

Front Panel Width:

261.8 mm (10.3 in.)

Note: 16-bit SCSI operation precludes the use of some PMC Slot 2

signals.

MVME761: 19.8 mm (0.8 in.)

MVME712M: 39.6 mm (1.6 in.)

Synchronous Serial Ports

Controller:

Number of Ports:

Configuration:

A l l M o d u l e s

85230/8536

Two (IPMC761); one (IPMC712)

All Modules

IPMC761: TTL to P2 (both ports), SIM

configurable on MVME761;

IPMC712: EIA-232 to P2

Environmental

(Minimum of 400 LFM (linear feet per minute) of forced air cooling is

recommended for operation in the higher temperature ranges.)

Baud Rate, bps max.:

2.5M sync, 38.4K async

10 MHz/5 MHz

Operating

Nonoperating

Oscillator Clock Rate

(PCLK):

Temperature:

0° C to +55° C

(inlet air temp. w/forced

air cooling)

–40° C to +85° C

Asynchronous Serial Ports

Controller:

Number of Ports:

Configuration:

16C550 UART; 85230/8536

Humidity (NC):

Vibration:

5% to 90%

Two (IPMC761); three (IPMC712)

2 Gs RMS,

20–2000 Hz random

6 Gs RMS,

20–2000 Hz random

EIA-574 DTE (IPMC761);

EIA-232 (IPMC712)

Async Baud Rate, bps

max.:

38.4K EIA-232, 115Kbps raw

Demonstrated MTBF

MVME761 Compatible I/O

(based on a sample of eight boards in accelerated stress environ-

ment; results pending for IPMC712)

IPMC761-001

Multifunction rear I/O PMC module; Ultra

Wide SCSI, one parallel port, two async and

two sync/async serial ports

Mean:

190,509 hours

107,681 hours

95% Confidence:

MVME761-001

Transition module: Two DB-9 async serial port

connectors, two HD-26 sync/async serial port

connectors, one HD-36 parallel port connec-

tor, one RJ-45 10/100 Ethernet connector;

includes 3-row DIN P2 adapter module and

cable (for 8-bit SCSI)

Safety

All printed wiring boards (PWBs) are manufactured with a flammabil-

ity rating of 94V-0 by UL recognized manufacturers.

Electromagnetic Compatibility (EMC)

Intended for use in systems meeting the following regulations:

MVME761-011

Transition module: Two DB-9 async serial port

connectors, two HD-26 sync/async serial port

connectors, one HD-36 parallel port connec-

tor, and one RJ-45 10/100 Ethernet connec-

tor; includes 5-row DIN P2 adapter module

and cable (for 16-bit SCSI); requires back-

plane with 5-row DIN connectors

U.S.:

FCC Part 15, Subpart B, Class A (non-residential)

Canada:

ICES-003, Class A (non-residential)

This product was tested in a representative system to the following

standards:

CE Mark per European EMC Directive 89/336/EEC with Amend-

ments; Emissions: EN55022 Class B; Immunity: EN55024

(results pending for configurations with IPMC712)

SIM232DCE or DTE

SIM530DCE or DTE

SIMV35DCE or DTE

SIMX21DCE or DTE

EIA-232 DCE or DTE Serial Interface Module

EIA-530 DCE or DTE Serial Interface Module

V.35 DCE or DTE Module

O r d e r i n g I n f o r m a t i o n

X.21 DCE or DTE Serial Interface Module