MicroBoards Technology DX 2 User Manual

DX-2 Disc Publisher Installation  
Quick Reference Guide  
Driver Installation:  
PrassiTech Zulu2 Installation:  
Windows 2000 and Windows XP will find the new hardware and will step you through  
the installation process.  
For a more in-depth look at the  
installation process, please refer to  
the Installation section of the User’s  
Manual.  
1. Click the Next button to begin the Zulu2 installation process.  
1. Once the Hardware Setup is complete, verify that the printer is fully powered on  
and the connections to the computer are secure.  
2. After the installation process completes, remove the check from the Reboot  
Computer box and click Finish. Rebooting will occur after installing SureThing.  
2. Turn on the computer to which  
the DX-2 Disc Publisher is  
connected. Once the computer  
boots, you will be notified that the  
new USB connection has been  
found.  
SureThing CD Labeler Installation:  
1. Click the Start button and select Run from the Start menu. Click the Browse  
button and go to the CD/DVD drive, highlight SureThing.exe and click the  
Open button, then click OK.  
Hardware Setup:  
1. Unpack the DX-2 Disc Publisher and place it in the selected workspace. This  
space should have enough vertical space to allow for easy loading of media into  
the input hopper and have enough room at the back to allow for any rejected  
discs to exit the DX-2 Disc Publisher without obstacles.  
2. Read the Software License and Warranty information and click the I Accept  
button to continue the installation of SureThing.  
3. Click the Next button.  
3. Click the Next button at the Welcome screen.  
4. Place the DX-2 Disc Publisher  
Software CD into the CD/DVD  
ROM drive.  
2. Plug in the power cord to the back of the DX-2 Disc Publisher and turn on the  
switch located on the back of the unit. Next, press the power button on the front  
panel to turn on the printer.  
4. To install to the default directory,  
click Next on the Select  
Destination Directory screen. If  
you wish to install to a different  
location, select that location  
before clicking Next.  
3. Install the Output Bin on the front of the DX-2 Disc Publisher and tightly  
secure using the 2 thumbscrews.  
5. Windows 2000: Select the option to Search for a suitable driver, and click  
Next. Check the CD-ROM Drives Box and click Next. Click the Next button  
again when you are notified that the driver has been found.  
4. Install the Microboards ink cartridges.  
Windows XP: Select the option to Install from a list or specific location and  
click Next. Check the Search Removable Media box and click Next.  
THE DX-2 DISC PUBLISHER WILL ONLY OPERATE WITH  
MICROBOARDS INK CARTRIDGE MODELS PRF19ML AND PRF38ML.  
5. Select adding a desktop  
shortcut and the location in which  
the Start Menu shortcut will be  
created, or make no changes to  
select the default locations.  
Click Next when the locations  
are suitable.  
6. The Digital Signature screen will appear. Click the Yes button at the bottom of  
A. Remove the tape from the front of the DX-2 Disc Publisher, lift the lid, and  
remove the tape from the print carriage once it has moved to the center of the  
printer.  
the screen. The drivers will then be copied to the hard drive.  
7. Once the USB drivers have been copied, click the Finish button.  
B. Raise the cradle latches. Remove the ink cartridges from the packaging  
and carefully remove the plastic tape covering the print head.  
8. The Print driver installation will occur next. Repeat steps 3 through 7 to install  
the print drivers.  
6. Click Start on the next screen to install the application.  
C. Gently push the ink cartridges into the appropriate cradles. Do not try to  
force the cartridges into place as doing so may damage the cartridge.  
9. Verify the installation of the DX-2 Disc Publisher by clicking the Start button.  
Select Printers and Faxes from the Start menu, either through the Settings  
menu for Windows 2000 or directly in the Start menu for Windows XP. You will  
see the new printer installed and available for use.  
7. Click Finish once the installation is complete. You will also have the opportunity  
D. Secure the cradle latches and close the lid. The print carriage will return to  
the right neutral position.  
to register the software on-line.  
8. The driver and software installation is now  
complete. The computer will need to be  
rebooted for the software to operate correctly.  
Click OK to reboot. If you choose not to reboot  
at this time, click the Cancel button to reboot  
later. Remember, the computer must be  
rebooted prior to running the DX-2 Disc  
Publisher, Zulu2, or SureThing.  
5. Connect the DX-2 Disc Publisher to the computer using the USB cable provided.  
Please be sure the computer is off during this process.  
DX-2 Disc Publisher controller and Software Installation:  
A. Plug the small end of the USB cable into the back of the DX-2 Disc Publisher.  
The DX-2 Disc Publisher controllers, PrassiTech Zulu 2, and SureThing Disk Labeler  
are included on the Software disc.  
B. Plug the larger end of the USB cable into an available port on the  
PC. Confirm that both ends of the cable are securely connected.  
USB 2.0 support on the PC is required.  
DX-2 Disc Publisher Controller Installation:  
6. Turn the PC on at this point.  
1. Click the Start button and select Run from the Start menu. Click the Browse  
button and go to the CD/DVD drive, highlight Publisher.exe, click the Open  
button, then click OK.  
The Hardware Setup is now complete. Proceed to the installation of the DX-2 Disc  
Publisher Drivers and Software.  
Installation of the DX-2 Disc Publisher is complete. After rebooting,  
the printer will need to be aligned and the robotics configured prior  
to burning and printing disks. Please see the DX-2 Disc Publisher  
Configuration Quick Reference Guide on the other side of this page,  
or refer to the appropriate sections of the User’s Manual.  
2. Click the Next button on the next window. Once the window reads Ready to  
Install the Program, click the Install button. Click Finish once the installation  
completes. The Zulu2 software installation will begin automatically.  
820-00134-02  

JVC AV 14U17 User Manual
JVC CRT Television C 20310 User Manual
KitchenAid 4366501 User Manual
LG Electronics 1953TX BF User Manual
Magnavox 20MT1336 User Manual
Miele KM5952 User Manual
NEC MultiSync FE771SB User Manual
Panasonic KX FKN512 User Manual
Philips 3121 235 20691 User Manual
Philips BZ02 User Manual