Maytag MEC7630W User Manual

Electric Built-in Cooktop  
LOCATION REQUIREMENTS  
PRODUCT MODEL NUMBERS  
MEC7430W  
MEC7536W  
MEC7630W  
MEC7636W  
IMPORTANT: Observe all governing codes and ordinances. When installing cooktop, use  
minimum dimensions given.  
To eliminate the risk of burns or fire by reaching over the heated surface units, cabinet storage  
Electrical:  
space located above the surface units should be avoided. If cabinet storage is to be provided, the  
risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7  
cm) beyond the bottom of the cabinets.  
If codes permit and a separate ground wire is used,  
it is recommended that a qualified electrical installer  
determine that the ground path and wire gauge are  
in accordance with local codes.  
The cooktop must be a specified cooktop that is approved to be installed either alone or over an  
undercounter built-in oven. Check the cooktop base for an approved installation label. If you do  
not find this label, contact your dealer to confirm that your cooktop is approved.  
Ovens approved for this type of installation will have an approval label located on the top of the  
oven. If you do not find this label, contact your dealer to confirm that your oven is approved.  
Refer to oven manufacturer’s Installation Instructions for approval for built-in undercounter use  
and proper cutout dimensions.  
Check with a qualified electrical installer if you are  
not sure the cooktop is properly grounded.  
Make sure that the electrical connection and wire  
size are adequate and in conformance with the  
National Electrical Code, ANSI/NFPA 70-latest  
edition or CSA Standards C22.1-94, Canadian  
Electrical Code, Part 1 and C22.2 No. O-M91-latest  
edition, and all local codes and ordinances.  
The cooktop should be installed away from strong draft areas, such as windows, doors, fans or  
strong heating vents. The cooktop should be located for convenient use in the kitchen.  
Use the countertop opening dimensions that are given with these Installation Instructions. Given  
dimensions are minimum clearances and provide 0" (0 cm) clearance.  
Grounded electrical supply is required. See “Electrical Requirements” section.  
Before You Make the Electrical Connection:  
To properly install your cooktop, you must  
determine the type of electrical connection you will  
be using and follow the instructions provided for it  
here.  
IMPORTANT: To avoid damage, check with your builder or cabinet supplier to make sure that  
the materials used will not discolor, delaminate or sustain other damage.  
A 3-wire or 4-wire, single phase, 240 volt, 60-Hz.,  
PRODUCT DIMENSIONS  
AC only electrical supply is required on a separate,  
40-amp circuit for 30" (76.2 cm) models or 50-amp  
circuit for 36" (91.4 cm) models, fused on both  
sides of the line. The model/serial number rating  
plate is located on the metal cabinet underneath the  
cooktop. See the following illustration.  
B
A
C
A. 21¹⁄₂" (54.6 cm)  
B. 30" (76.2 cm) models - 30" (76.2 cm)  
36" (91.4 cm) models - 35⁵⁄₁₆" (89.7 cm)  
C. 3³⁄₄" (9.5 cm)  
CABINET DIMENSIONS  
IMPORTANT: If installing a range hood or microwave hood combination above the cooktop,  
follow the range hood or microwave hood combination installation instructions for dimensional  
clearances above the cooktop surface.  
A
A. Model/serial number plate  
The cooktop is rated 240 volt and does not have a  
A
D
neutral (white) wire.  
The cooktop should be connected directly to the  
junction box through flexible, armored or  
nonmetallic sheathed, copper cable. The flexible,  
armored cable extending from the fuse box or  
circuit breaker box should be connected directly to  
the junction box.  
B
C
F
G
E
Locate the junction box to allow as much slack as  
possible between the junction box and the cooktop  
so that the cooktop can be moved if servicing  
becomes necessary in the future.  
A. 30" (76.2 cm) on 30" models; 36" (91.4 cm)  
on 36" models  
B. Combustible area above countertop (shown  
by dashed box above)  
C. 30" (76.2 cm) minimum clearance between  
top of cooktop platform and bottom of  
unprotected wood or metal cabinet  
(24" [61 cm] minimum clearance if bottom of  
wood or metal cabinet is shielded by not  
less than ¹⁄₄" [0.6 cm] flame retardant  
millboard covered with not less than No. 28  
H
H
Do not cut the conduit. The length of conduit  
I
J
provided is for serviceability of the cooktop.  
A UL listed or CSA approved conduit connector  
must be provided at each end of the power supply  
cable (at the cooktop and at the junction box). A  
listed conduit connector is already provided at the  
cooktop.  
If the house has aluminum wiring follow the  
MSG sheet steel, 0.015" [0.04 cm] stainless steel, or 0.024" [0.06 cm] aluminum or 0.020"  
[0.05 cm] copper)  
procedure below:  
1. Connect a section of solid copper wire to the  
pigtail leads.  
D.13" (33 cm) recommended upper cabinet depth  
E. 2¹⁄₈" (5.4 cm)  
2. Connect the aluminum wiring to the added  
section of copper wire using special connectors  
and/or tools designed and UL listed for joining  
copper to aluminum.  
F. 20³⁄₈" +/- ¹⁄₁₆" (51.75 +/- 0.16 cm)  
G.18" (45.7 cm) minimum clearance from upper cabinet to countertop within minimum horizontal  
clearances to cooktop  
H. Junction box or outlet: 6" (15.2 cm) minimum from top of counterop; 7" (17.8 cm) maximum  
from right side of cabinet  
I. 29¹⁄₁₆" +/- ¹⁄₁₆" (73.8 +/- 0.16 cm) on 30" (76.2 cm) models 34⁹⁄₁₆" +/- ¹⁄₁₆" (87.8 +/- 0.16 cm) on  
36" (91.4 cm) models  
J. 1" (2.5 cm) minimum distance to nearest left and right side combustible surface above cooktop  
Follow the electrical connector manufacturer's  
recommended procedure. Aluminum/copper  
connection must conform with local codes and  
industry accepted wiring practices.  
Because Whirlpool Corporation policy includes a continuous commitment to improve  
our products, we reserve the right to change materials and specifications without notice.  
Dimensions are for planning purposes only. For complete details, see Installation  
Instructions packed with product. Specifications subject to change without notice.  
Ref. W10274255A  
10-06-09  

Intel Box Core I5 4570 3 2g BX80646I54570 User Manual
JVC AV 21D33 AV 20N33 AV 14F33 AV 21D13 AV 20N13 AV 14F13 User Manual
JVC InteriArt AV 32X4SU User Manual
JVC Professional 19" LCD Monitor GD 191U User Manual
Lenovo Computer Hardware Q190 User Manual
Life Fitness 95C User Manual
Moffat Blue Seal G518A RB User Manual
Philips 28PW9515 User Manual
Philips 220CW9FW User Manual
Philips Brilliance 190SW9FB User Manual