MaxTech XT 7871 User Manual

XT-7871  
USER'S MANUAL  
Features  
0.28 mm Dot Pitch  
1280 x 1024, Non-Interlaced  
120 Hz Refresh Rate  
PowerSavingOperation(VESADPMS)  
Anti-Static, Anti-Glare Screen  
Full Screen Display  
Digital Controls with OSD  
Low Radiation (MPR-II)  
Plug and Play  
Three-Year Warranty  
Part#MAN124Rev. 1.0  
XT7871  
Section 1 - General Information  
Congratulations on purchasing a MaxTech 17-inch high resolution color monitor.  
The monitor uses one of the finest CRTs available in the industry. The 0.28 mm  
dot pitch non-glare tube provides a crisp and vivid color display. The monitor  
complies with the MPR-II standard to reduce electro-magnetic emissions. Ad-  
vanced electronics and digital controls make it the perfect monitor for applications  
ranging from home computing to business presentations.  
The monitor is compatible with VGA, SVGA, and XGA display adapters. It  
operates at resolutions ranging from 640 x 350 to 1280 x 1024 with unlimited  
colors. The monitor is PnP (Plug and Play) compliant to simplify setup and  
configuration in Windows 95 or other PnP operating systems.  
1.1 Precautions When Using the Monitor  
When setting up and using your monitor, pay special attention to the following:  
• To eliminate eye fatigue, do not use your monitor against a bright background  
or where sunlight or other light sources will shine directly on the monitor.  
• Your monitor should be placed just below eye level for optimum viewing.  
• Allow adequate ventilation around the monitor so that heat from the monitor  
can properly dissipate.  
• Neither the monitor itself nor any other heavy object should rest on the power  
cord. Damage to a power cord can cause fire or electrical shock.  
• Keep the monitor away from high capacity transformers, electric motors and  
other strong magnetic fields.  
• Do not use your monitor in a damp, dusty or dirty area.  
• Handle the monitor with care when transporting.  
• Unplug the monitor during electrical storms  
Section 2 - Installation  
• Plug the 15-pin male connector on the video cable into the output connector  
on the rear of your computer system. The video output connector on your  
computer may be either in a location similar to Figure 2-1 or on an expansion  
board. Secure the cable to the computer using the thumbscrews on the 15-  
pin connector.  
• Attach the power cord to the monitor and plug it into an AC outlet.  
• The monitor is now ready for use.  
2
Figure 2-1 Monitor Connections  
ds  
Section 3 - Monitor Controls and LEDs  
3.1 Controls and LEDs  
Figure 3-1 Master Power Control  
1
3
Figure 3-2 Control and LED Locations  
2
3
8
7
6
5
4
1. Master Power (On rear): Push to provide power to the monitor. This switch  
should be left ON for daily operation. Use the front panel On/Off control (3) to  
turn the monitor display on and off.  
2. Power Saving Indicator: When lit, the monitor is in the DPMS OFF mode.  
3. ON/OFF: Press this switch to turn the monitor display on, press again to turn  
the monitor display off.  
4. Power On Indicator: When lit the monitor is powered on  
5. Adjust: Press plus (+) to increase the setting for the selected OSD param-  
eter. Press minus (-) to decrease the setting.  
6. Select:PresseitherbuttontoenabletheOSDdisplay. Press(Ø)toselectthe  
next OSD parameter. Press (×) to select the previous OSD parameter.  
7. Contrast Control: Adjusts the contrast of the display.  
8. Brightness Control: Adjusts the display brightness.  
4
3.2 On-Screen Display  
1280 X 1024  
H: 64KHz  
V: 60Hz  
A
B
C
D
E
F
G
H
I
The On-Screen Display (OSD) is enabled by pressing either button of control  
pair 6 (see Figure 3-2). Control pair 5 (+ and -) buttons are used to increase or  
decrease the value of selected parameter.  
A. Horizontal-Size: Adjusts the display width. The (+) button increases the  
width. The (-) button decreases the width.  
B. Horizontal-Position: Adjusts the horizontal position. The (+) button moves  
the display to the right. The (-) button moves the display to the left.  
C. Vertical-Size: Adjusts the display height. The (+) button increases the  
height. The (-) button decreases the height.  
D. Vertical-Position: Adjusts the vertical position. The (+) button moves the  
display up. The (-) button moves the display down.  
E. Pincushion: Adjusts the shape of the left and right sides of the display. The  
(+) button makes the display sides curve out. The (-) button makes the  
display sides curve in.  
F. Trapezoid: Adjusts the shape of the left and right sides of the display. The  
(+) button makes the display sides slant out. The (-) button makes the display  
sides slant in.  
G. Rotation: Adjusts the amount the display area will tilt. The (+) button rotates  
the display clockwise. The (-) button rotates the display counter-clockwise.  
H. Degauss: Press (+) or (-) to clear color impurity of the display.  
I. Recall: Press (+) or (-) to reset parameters A-G to factory default values.  
5
Section 4 - Troubleshooting  
No picture, no LEDs lit.  
Check that the AC cord is plugged into an outlet and the monitor.  
Turn on the Master Power switch.  
No picture, power LED is lit.  
Monitor is in DPMS STANDBY/SUSPEND mode. Press a key or move the  
mouse.  
Check that video cable is connected completely.  
Adjust brightness and contrast controls.  
Check connector for bent pins.  
No picture, power saving indicator (2) on.  
Monitor is in DPMS OFF mode. Press a key or move the mouse.  
Monitor is off. Press front panel On/Off switch.  
Check connector for bent pins.  
Image is not centered  
Adjust Vertical Position and Horizontal Position controls.  
6
Appendix A - Specifications  
Picture Tube  
Size  
17-inch diagonal  
0.28mm  
Dot pitch  
Horizontal Freq  
Vertical Freq.  
Resolution (Max.)  
Video Dot Rate  
Data Area  
30-66KHz  
50-120 Hz  
1280 x 1024  
100 MHz  
11.8 in. x 8.7 in.  
Maximum Refresh Rates  
Resolution  
Refresh (Vertical) Frequency  
640 x 480  
800 x 600  
1024 x 768  
1280 x 1024  
120Hz  
100 Hz  
80 Hz  
60 Hz  
Input voltage  
Front controls  
110~240VAC, 50/60 Hz  
On/Off, Adjust, Select, Contrast, Brightness  
Horizontal-Size, Horizontal-Position, Vertical-Size, Verti-  
cal-Position, Pincushion, Trapezoid, Rotation, Degauss,  
Recall  
Rear Control  
Master Power  
120 W (Max.)  
Power  
Consumption  
Power saving  
Display Power Management Signaling (DPMS)  
SUSPEND/STANDBY mode  
OFF mode  
20W (Max.)  
1W (Max.)  
Low Radiation  
Standard  
MPR-II  
Plug and Play  
DDC1, DDC2B  
Operating  
Environment  
Temperature  
Humidity  
5°~35°C  
30~80%  
Connector  
15 Pin D-Sub  
Dimensions  
16.6 (W) x 16.7 (D) x 16.6 (H)  
Specifications subject to change without notice.  
7
Appendix B - Video Cable Pinout  
Figure B-1 Pin Layout and Pin Assignment Chart  
PIN SIGNAL  
PIN SIGNAL  
No Pin  
1
2
3
4
5
6
7
Red  
9
Green  
10 Ground  
11 Ground  
12 SDA  
Blue  
No Pin  
Ground  
Red Return  
Green Return  
13 Hor. Synch.  
14 Vert. Synch  
15 Data Clock  
(SCL)  
8
Blue Return  
Appendix C - Power Saving Modes (DPMS)  
VESA Display Power Management Signaling (DPMS) defines a method for a  
computer to signal the monitor to reduce its power consumption when idle. DPMS  
features must be supported by both the computer and the monitor. This monitor  
supports DPMS “SUSPEND” “STANDBY” and “OFF” modes. Computer support  
of DPMS requires the use of a DPMS compliant video card driver.  
The monitor enters DPMS STAND-BY or SUSPEND mode when the computer  
turns off either the Horizontal or Vertical Synchronization signal. These power-  
saving modes reduce the monitor’s power consumption to 20W. When the  
synchronization signals are re-enabled the monitor returns to normal operation.  
The monitor enters DPMS OFF mode when the computer turns off both the  
Horizontal and Vertical Synchronization signals. This mode reduces the monitor’s  
power consumption to 1W. When the synchronization signals are re-enabled the  
monitor returns to normal operation.  
8
Appendix D - Three Year Warranty  
MAXTECH warrants to the original buyer of this product against defects in  
material and workmanship for three years from the date of purchase.  
Except as specified below, this warranty covers all defects in material or  
workmanship in this product. The following are not covered by the warranty:  
1. Any product which is not distributed in North America by MAXTECH or which  
is not purchased in North America from an authorized MAXTECH Dealer.  
2. Any product on which the serial number has been defaced, modified or  
removed.  
3. Damage, deterioration or malfunction resulting from:  
a. Accident, misuse, abuse, neglect, fire, water, lightning or other acts of  
nature, commercial or industrial use, unauthorized product modification, or  
failure to follow instructions supplied with the product.  
b. Repair or attempted repair by anyone not authorized by MAXTECH.  
c. Any shipment of the product (claims must be presented to the carrier).  
d. Removal or installation of the product.  
e. Any other cause which does not relate to a product defect.  
4. Cartons, carrying cases, batteries, external cabinets, magnetic tapes or any  
accessories used in connection with the product.  
MAXTECH will pay all labor and material expenses for covered items, but we will  
not pay for the following:  
1. Removal or installation charges.  
2. Costs of initial technical adjustments (set-up), including adjustment of user  
controls.  
3. Payment of shipping charges.  
HOW TO OBTAIN WARRANTY SERVICE  
Intheeventtheproductrequiresservice, calltheMaxTechServiceCenterat(562)  
921-4438 between 9:00 a.m. and 6:00 p.m. (PST Monday through Friday). When  
you are instructed by the Technical Support Representative to return the product  
to MaxTech for repair, you will be given an RMA (Return Merchandise Authoriza-  
tion) number. You must have an RMA Number to return the product for  
service. Use the following procedure to return the product to MaxTech:  
1. Return the product in its original package and packing (if possible).  
2. Be sure to include your name, address, day-time telephone number, RMA  
number, and a brief description of the problem (also enclose a check for  
out-of-warranty repair).  
3. After wrapping the package securely for shipping, print your name, return  
address and the RMA # clearly on the outside of your package.  
4. Ship the unit prepaid via UPS or the U.S. Postal Service to the address  
provided by the technician when you call. We recommend that the unit be  
insured.  
This warranty is valid for products sold in North America only. Contact your local  
authorized distributor or dealer for the warranty offered in other areas.  
9
All warranty services must be performed by Authorized Service Centers. There  
are no user serviceable parts inside the unit. Do not remove any components or  
attempt to service the unit by any unauthorized service center. This warranty is  
voided if the product has been abused, misused, modified, or repaired by an  
unauthorized service center.  
LIMITATION OF IMPLIED WARRANTIES  
All implied warranties, including warranties of merchantability and fitness for a  
particular purpose, are limited in duration to the length of this warranty.  
EXCLUSION OF DAMAGES  
MAXTECH'S liability for any defective product is limited to the repair or replace-  
ment of the product, at our option. MAXTECH shall not be liable for:  
1. Damage to other property caused by any defects in this product, damages  
based upon inconvenience, loss of use of the product, loss of time, commer-  
cial loss; or  
2. Any other damages, whether incidental, consequential or otherwise.  
Some states do not allow limitations on how long an implied warranty lasts and/  
or do not allow the exclusion or limitation of incidental or consequential damages,  
so the above limitations and exclusions may not apply to you.  
HOW STATE LAW RELATES TO THE WARRANTY  
This warranty gives you specific legal rights, and you may also have other rights  
which vary from state to state.  
Appendix E - Notices  
FCC Class B Statement  
This equipment has been tested and found to comply with the limits for a Class  
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed  
to provide reasonable protection against harmful interference in a residential  
installation. This equipment generates, uses and can radiate radio frequency  
energy, and if not installed and used in accordance with the instructions, may  
cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this  
equipment does cause harmful interference to radio or television reception, which  
can be determined by turning the equipment off and on, the user is encouraged  
to try to correct the interference by one or more of the following measures:  
• Reorient or relocate the receiving antenna  
• Increase the separation between the equipment and the receiver  
• Connect the equipment into an outlet on a circuit different from that to which  
10  
the receiver is connected  
• Consult the dealer or an experienced radio / TV technician for help  
Notice: Shielded cables, if any, must be used in order to comply with the emission  
limits. Any change or modification not expressly approved by the Grantee of the  
equipment authorization could void the user’s authority to operate the equipment.  
Canadian DOC Compliance Statement  
This equipment does not exceed Class B limits for radio noise emissions for a  
digital apparatus, set out in the Radio Interference Regulations of the Canadian  
Department of Communications. Operation in a residential area may cause  
unacceptable interference to radio and TV reception requiring the owner or  
operator to take whatever steps necessary to correct the interference.  
Cet équipement ne dépasse pas les limits de Class B d'émission de bruits  
radioélectriques pour les appareils numériques, telles que prescrites par le  
Règlement sur le brouillage radioélectrique établi par le ministère des Commu-  
nications du Canada. L'exploitation faite en milieu résidentiel peut entraîner le  
propriétaire ou l'opérateur à prendre dispositions nécessaires pour en éliminer  
les causes.  
Disclaimer, Copyright, And Other Notices  
The information contained in this manual has been validated at the time of this  
manual's production. The manufacturer reserves the right to make any changes  
and improvements in the product described in this manual at any time and without  
notice. Consequently, the manufacturer assumes no liability for damages in-  
curred directly or indirectly from errors, omissions or discrepancies between the  
product and the manual.  
All registered trademarks are the property of their respective owners.  
Copyright © 1997 MAXTECH. All rights reserved. No reproduction of this  
document in any form is allowed without written permission from MAXTECH.  
First Edition  
GZ/DR - Version 1.0  
11  

Indesit KD6G25XIR User Manual
Intel Dual Band Wireless AC 7260 7260HMWWB User Manual
KitchenAid KEBI241 User Manual
KitchenAid KEBS277SBL1 User Manual
Mermaid Technology 170 User Manual
Panasonic GT21C User Manual
Philips 25CE6590 User Manual
Philips 28PW6332 User Manual
Philips Brilliance 170S2B User Manual
Philips Magnavox 14MS2331 User Manual