MSi MS 6834B User Manual

MSI PC60G (MS-6834B)

Wireless 11g Turbo G PCI Card

User’s Manual

Prescribed use:

This product integrates a WLAN- and/or Bluetooth^®device.

The device sets up a radio link between to computer. In addition it is possible to

link the WLAN- or Bluetooth^®device to any other WLAN- or Bluetooth^®device

which stick to the IEEE 802.11b/g or Bluetooth^®requirements.

Hinweise zur Reichweite:

Der Abstand zwischen Sender und Empfδnger (von einem WLAN- oder Bluetooth^®

-Gerδt zu einem entsprechenden anderen Gerδt) hδngt stark von der

Einsatzumgebung ab. Wδnde, Betonboden (Eisen), beschichtete Fensterscheiben,

Fahrzeug-Karosserie, etc..

Weitere Beeinflussungen:

- Hochfrequenzaussendungen jeder Art

- Gebδude, Bδume, etc.

- Heizkφrper, Stahlbeton, etc.

- offen betriebene Computer, etc.

- Mikrowellenherde, etc,

Die Kommunikation zwischen unterschiedlichen WLAN- oder Bluetooth^®

Gerδten ist von der jeweiligen Software und dem entsprechenden Versionsstand

abhδngig

Operating range:

The transmission range between different WLAN- or Bluetooth^®devices varies

depending the specific environment. Walls, concrete floor (iron), laminated

windows, vehicle-body, etc..

More electromagnetic interferences:

- high frequency emission of any kind,

- Buildings, trees, etc.

- Heaters, ferroconcrete, etc.

- open computer systems, etc.

- Microwave oven, etc,

Communication (exchange data) is dependent on the software of the WLAN or

Bluetooth^®devices.

MSI Technology GmbH

Hanauer Landstraίe 306

60314 Frankfurt

Telefon: +49 (0)69 40893-0

Telefax: +49 (0)69 40893-202

iii

FCC Caution

1. The device complies with Part 15 of the FCC rules. Operation is subject to

the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference

that may cause undesired operation.

2. FCC RF Radiation Exposure Statement: The equipment complies with FCC

RF radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with a minimum

distance of 20 centimeters between the radiator and your body.

3. This Transmitter must not be co-located or operating in conjunction with

any other antenna or transmitter.

4. Changes or modifications to this unit not expressly approved by the

party responsible for compliance could void the user authority to operate

the equipment.

The material in this document is the intellectual property of MICRO-STAR INTERNA-

TIONAL. We take every care in the preparation of this document, but no guarantee is

given as to the correctness of its contents. Our products are under continual improve-

ment and we reserve the right to make changes without notice.

Trademarks

Microsoft Windows and Internet Explorer are registered trademarks or trademarks of

Microsoft Corporation.

All brand names, icons, and trademarks used in this manual are the sole property of their

respective owners.

Revision History

Revision

V 1.0

History

First Release

Date

September 2006

Important Safety Precautions

Always read and follow these basic safety precautions carefully when handling any

piece of electronic component.

1. Keep this User’s Manual for future reference.

2. Keep this equipment away from humidity.

3. Lay this equipment on a reliable flat surface before setting it up.

4. The openings on the enclosure are for air convection hence protects the

equipment from overheating.

5. All cautions and warnings on the equipment should be noted.

6. Never pour any liquid into the opening that could damage or cause electrical

shock.

7. If any of the following situations arises, get the equipment checked by a

service personnel:

Liquid has penetrated into the equipment

The equipment has been exposed to moisture

The equipment has not work well or you can not get it work

according to User’s Manual

The equipment has dropped and damaged

If the equipment has obvious sign of breakage

8. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT

UNCONDITIONED, STORAGE TEMPERATURE ABOVE 70^OC OR

BELOW -20^OC, IT MAY DAMAGE THE EQUIPMENT.

Table of Contents

Chapter 1. Introduction .............................................................................................1

1.1 PC60G - MSI Wireless 11g Turbo G PCI Card ....................................................1

1.2 How PC60G Works .............................................................................................2

1.3 Specifications......................................................................................................4

1.4 System Requirements .........................................................................................6

1.5 Package Contents ...............................................................................................6

1.6 Product View ......................................................................................................7

Chapter 2. Hardware Installation ............................................................................8

Chapter 3. Software Installation .............................................................................10

Chapter 4. Wireless Network Utility ......................................................................13

4.1 Introduction ..........................................................................................................13

4.1.1 The MSI Wireless LAN Icon ........................................................................13

4.1.2 Changing the Control Setting (for Windows XP only) ..............................15

4.2 Networking ..........................................................................................................16

4.2.1 Infrastructure Mode ....................................................................................16

4.2.2 Ad-hoc Mode...............................................................................................22

4.3 Link Status ...........................................................................................................24

4.4 Statistics ..............................................................................................................25

4.5 About ...................................................................................................................26

Chapter 5. MSI Software AP Setup ........................................................................27

Chapter 6. Networking Basics ................................................................................30

6.1 Setup ...................................................................................................................30

6.2 Configuration .......................................................................................................33

6.3 Confirmation ........................................................................................................34

Chapter 7. Networking Basics ................................................................................35

7.1 Checking the Network Elements ........................................................................35

7.2 Computer Identification .......................................................................................37

7.3 Configuring a Dynamic/Fixed IP Address ..........................................................40

7.4 Checking TCP/IP Address ...................................................................................44

7.5 Checking Connection by Pinging ........................................................................46

7.6 Sharing Files ........................................................................................................47

Chapter 8. Trouble Shooting....................................................................................51

Appendix: CE Compliance Booklet .........................................................................56

Introduction

>>> 1.1 PC60G - MSI Wireless 11g Turbo G PCI Card

The MSI PC60G Wireless 11g Turbo G PCI Card (hereafter

called PC60G), compliant with IEEE802.11g, is a high-efficiency

wireless adapter for wireless networking at home, in office or in

public places. The data rate can be up to 54 Mbps and auto-

negotiated to 48, 36, 24, 18, 12, 9, 6Mbps (IEEE 802.11g), or 11,

5.5, 2, 1Mbps (IEEE802.11b).

With PC60G, you can roam between conference room and

office without being disconnected the LAN cables; in addition,

sharing files and printers can be easy tasks.

The PC60G is available to Microsoft Windows operating sys-

tems (Windows^®XP/2000/ME/98SE/XP 64-bit) and can be inte-

grated into networking with either Ad-hoc mode (computer-to-

computer, without an Access Point) or Infrastructure mode

(computer-to-access point, an Access Point is required).

*Experiencing the high throughouput of the MSI Turbo G mode,

MSI Turbo G series wireless products are highly recommended

as your best choices. MSI Turbo G mode is suggested to func-

tion with MSI Turbo G series wireless products to optimize

performance. The compatibility of other brands of wireless

products with MSI Turbo G mode is not guaranteed.

(MSI Turbo G Mode support is also required on host/router

side, such as the MSI RG60G).

Actual throughput value might vary due to environmental, opera-

tional and other factors.

>>> 1.2 How PC60G Works

Ad-hoc Mode : An Ad-hoc network is a local area network or other

small network, especially one with wireless or temporary plug-in

connections, in which some of the network devices are part of

the network only for the duration of a communications session.

Users in the network can share files, print to a shared printer,

and access the Internet with a shared modem. In this kind of

network, new devices can be quickly added; however, users can

only communicate with other wireless LAN computers that are in

this wireless LAN workgroup, and are within range.

PC60G

MSI Wireless 11g Turbo G PCI Card

Infrastructure Mode : The difference between Infrastructure net-

work and Ad-hoc network is that the former one includes an

Access Point. In an Infrastructure network, the Access Point can

manage the bandwidth to maximize bandwidth utilization. Addi-

tionally, the Access Point enables users on a wireless LAN to

access an existing wired network, allowing wireless users to

take advantage of the wired networks resources, such as Internet,

email, file transfer, and printer sharing. The scale and range of

the Infrastructure networking are larger and wider than that of

the Ad-hoc networking.

>>> 1.3 Specifications

Network Standard

IEEE802.11b/g

Frequency Band

Special Feature

Interface

2.400-2.4835GHz

Support MSI Turbo G Mode* Technology

Compliant with the 32-bit PCI v2.2 and above

Dipole

Antenna

Data Rate

IEEE802.11g (auto-fallback):

- OFDM: 54, 48, 36, 24, 18, 12, 9 and 6 Mbps

IEEE 802.11b (auto-Fallback):

- CCK: 11, 5.5 Mbps

- DQPSK: 2 Mbps

- DBPSK: 1 M bps

Media Access Protocol

Channel

CSMA/CA witha ACK

IEEE802.11g

IEEE 802.11b

Ch. 1-11--N. America

Ch. 1-13--Japan

Ch. 1-11--N. America

Ch. 1-14--Japan

Ch. 1-13--Europe ETSI Ch. 1-13--Europe ETSI

Ch. 10-11--Spain

Ch. 10-13--France

Transmission

Modulation

IEEE802.11b (DSSS),IEEE 802.11g(OFDM)

IEEE 802.11b(DSSS) IEEE802.11g(OFDM)

CCK@11, 5.5 Mbps

DQPSK@2Mbps

DBPSK@1Mbps

BPSK@6,9Mbps

QPSK@12,18Mbps

16-QAM@24, 36 Mbps

64-QAM@48, 54 Mbps

Network Architecture

Ad-Hoc Mode (Peer to Peer)

Infrastructure Mode

*MSI Turbo G Mode support is also required on host/router side, such as the MSI

RG60G.

Temperature Operating

0^oC to 70^oC

-20^oC to 100^oC

Storage

Humidty

10% - 90% (non-condensing)

Power Consumption

802.11g (54Mbps)

[email protected] in continue Tx

[email protected] in continue Rx

[email protected] in Standby mode

802.11b(11Mbps)

[email protected] in continue Tx

[email protected] in continue Rx

[email protected] in Standby mode

Operating Voltage

Output Power

3.3V +/- 5%

802.11g

54Mbps, 14.0+2/-1 dBm

802.11b

11Mbps, 17.5+/-2 dBm

Receiver Sensitivity

54 Mbps OFDM@ 10% PER = -65dBm

11 Mbps CCK@ 8% PER = -80dBm

Range

Up to 400m (outdoor operating range)

Security

64/128-bit WEP, WPA, WPA2, TKIP,AES,

802.1x

Operating System

Certification

Dimension

Windows98SE/2000/ME/XP/XP 64-bit

FCC Part 15, CE, DGT, C-Tick, Wi-Fi

133.5(L)x121(W)x21.5(H) mm

Weight

46g (without antenna)

82g (with antenna)

>>> 1.4 System Requirements

Before installing the PC60G, your PC should meet the

following items:

- One desktop PC with an available PCI slot.

- Windows^®98SE/ME/2000/XP/XP 64-bit operating

system.

- Minimum 5MB free disk space for installing the driver

and utilities.

- One CD-ROM drive, double speed or higher.

>>> 1.5 Package Contents

Unpack the package and check all the items carefully. If

any item contained is damaged or missing, please con-

tact your local dealer as soon as possible. Also, keep the

box and packing materials in case you need to ship the

unit in the future. The package should contain the follow-

ing items:

- One Wireless 11g Turbo G PCI Card - PC60G.

- One external antenna.

- One Quick Installtion Manual.

- One Installation CD including drivers, utilities, and the

manual files.

>>> 1.6 Product View

Wireless 11g Turbo G PCI Card PC60G

External Antenna

Antenna Connector

Connecting the external antenna.

Golden Finger

PWR LED - GREEN, indicating the

networking status by:

ON - Power inputted

OFF - No power

LNK/ACT LED - GREEN, indicating

the networking status by:

ON - The WLAN PCI Card is

connected.

Flash -The WLAN PCI Card is

searching for available

Access Point or receiving/

transmitting data over the

wireless network.

Hardware Installation

The following diagrams provide you a basic installation

for your PC60G, which is suitable for most desktop PCs.

For more information about the PCI slot, please refer to

the user’s manual of your mainboard.

Remove the computer cover. Locate the available PCI

slot on your mainboard.

STEP

NOTE: TURN OFF your

system and disconnect

the power cable before

installing the PC60G.

PCI slot

Put the PC60G directly over the PCI slot and press it into

the slot firmly.

STEP

DO NOT hold the PC60G

on the golden finger while

installing; doing this may

cause interference or

damage.

Replace the computer cover after securing the PC60G

with a bracket screw.

STEP

Connect the external antenna to the connector on the

PC60G’s bracket.

If your are not skilled at installing

the PCI adapter, please ask the

vendor or an experienced

technician for help.

Connecting the

external antenna

Software Installation

This chapter describes the procedures of installing the

driver and utility. Follow the instruction step by step to

finish the installation. If you use Windows^®98SE/ME,

please prepare the Windows^®Setup CD at hand before

installing the driver; because the system will ask you to

insert the Setup CD to copy files during the installation.

Please NOTE that the PC60G should be installed into

your computer before installing the driver and utility.

Then, the operating system will detect a new device and

start to configure the new device. Click Cancel here to

start installation from the InstallShield Wizard.

Tip: The wireless

LAN adapter should

be installed into your

PC before installing

the driver and utility.

Click

>>> 3.1 Software Setup

After installing the Wireless PCI Card to your computer

and then turning on the computer, the operating system

will detect a new device and start the configuraton

automatically. Please CANCEL the pop-up window from

Found New Hardare Wizard to install necessary driver

and utility from the InstallShield Wizard of your Software

CD.

Insert the Software CD into your CD-ROM driver, and the

Setup program shall launch automatically.

STEP

If the Autorun program didn’t launch automatically, click

Start at the taskbar and select Run.... Type E:\setup.

exe (where E is your CD-drive) in the Open box and click

OK to launch the Setup program manually.

Click

STEP

The welcome screen of InstallShield Wizard appears.

Read and Accept the License Agreement; then click

Next.

STEP

The program will copy the necessary files to the system.

The progress indicator shall show the installing status.

Click Finish when the installation is completed. The

MSI Wireless LAN icon will appear in the status area.

MSI Wireless LAN icon

Wireless Network Utility

After installing the driver, MSI PC60G provides a conven-

ient and powerful utility that allows you to set up, configure,

and know your networking status easily and clearly.

>>> 4.1 Introduction

4.1.1 The MSI Wireless LAN icon

- Not connected to the network.

- Connected to the network.

- Receiving/transmitting data from/to the network.

When you move the mouse over the icon, it shows the

current connection information.

Right-clicking the icon will bring up a sub-menu contain-

ing more settings:

Launch Config Utilities

Launch the MSI Wireless utility to configure your

network setting.

Use Zero Configuration as Configuration utility

Windows XP also provides user another wireless utility

to choose from. If you intened to use the utility to set

your network, this item is selectable to change the MSI

Wireless Utility to the Windows XP Wireless Utility at

your reference.

Switch to AP Mode

If your MSI wireless LAN adapter supports Software AP

function, you shall see this item under the sub-menu,

which allows you to user MSI wireless adapter as a virtural

access point.

Exit

Close the program.

Clicking the icon will launch the utility as shown below to

configure your network settings.

Click

4.1.2 Changing the Control Setting (for Windows XP only)

If you use Windows XP, the wireless LAN is controlled

by the operating system (default). To take full advantage

of your MSI wireless adapter, it is recommended to use

the MSI Wireless Network Utility to control your wireless

LAN.

To change the control setting:

Click Start to select Network Connections under

Setting.

STEP

Right-click the Wireless Network Connection, select

Properties to bring up following dialogue windows.

Click Wireless Network and uncheck the Use

Windows to configure my wireless network settings,

then click OK.

Uncheck this option

Click

Now you can use the MSI Wireless Utility to configure

your wireless network settings.

STEP

>>> 4.2 Networking

Since PC60G is installed in your computer, you have to

configure the settings for communication to start working

in your network environment.

4.2.1 Infrastructure Mode

Infrastructure mode allows your computer to communi-

cate with the other computers in the network through an

Access Point. The following tasks should be done be-

fore you configure the settings:

- The Access Point must be turned on.

- Your computer with wireless adapter installed

and the Access Point must be located with the

communication range of the Access Point (see

the Access Point's manual for details).

Connecting to the Access Point:

STEP

Click the MSI Wireless LAN icon to bring up the

Wireless Network Connection window.

Click

STEP

In the tab of Site Survey, select the network you want,

and then click Connect.

You also can click Rescan to search the available

Access Point in the network again.

Select

STEP

If the Access Point selected to connect has been

connected and had set up the Authentication and

Security, you need to have the WPA Pre-shared Key or

WEP Key beforehand from the Access Point

administrator to enter in the blank. Then click OK to

complete the configuration.

Enter WPA

Preshared

Key

Click

Please refer to page 19 for more detail configuration

regarding Add to Profile selection.

STEP

Advanced network settings:

STEP

Click the Advanced in the MSI Wireless Utility window

to set advanced network settings.

Wireless mode: Select wireless mode. 802.11 B/G mix,

802.11b only, and 802.11g only modes are supported.

B/G Protection: ERP protection mode of 802.11g

definition. User can choose from Auto, On, and Off.

a. Auto: STA will dynamically change as AP

announcement.

b. On: Always send frame with protection.

c. Off: Always send frame without protection.

Tx Rate: Manually force the Transmit using selected

rate. Default is Auto.

Tx Burst: MSI proprietary frame burst mode.

Fast Roaming at: Fast to roaming, setup by transmit

power.

Select Your Country Region Code: Seven countries to

choose.

CCX2.0: Support Cisco Compatible Extensions

function.

a. LEAP turn on CCKM

b. Enable Radio Measurement: can channel

measurement every

0~2000 milliseconds.

Turn radio ON/OFF for FAA requirement.

a. Radio On: Indicate to turn on radio.

b. Radio Off: Indicate to turn off radio.

Apply: Apply the above changes.

Add Profile to keep your favorite wireless settings:

STEP

Click the Profile in the MSI Wireless Utility window to

select Add or click Add to Profile after you select one of

available Access Point under Site Survey window to

configure your favorite wireless settings. You may save

multiple profiles, and activate the correct one at your

preference.

Click

After click Add to bring up the Configuration dialogue

window as below.

STEP

Profile Name: User chose name for this profile.

SSID: User can key in the intended SSID name or use

pull .

Power Save Mode: Choose from CAM (Constantly

AwakeMode) or Power Saving Mode. There is a check

box for “CAM when AC power”. When this is checked,

the wireless NIC will stay full power when AC power

cord is plug into power outlet.

Network Type: There are two types, infrastructure and

802.11 ad-hoc modes. Under ad-hoc mode, user can

also choose the preamble type; the available preamble

type includes short and long. In addition to that, the

“channel” and “Ad hoc wireless mode” field will be

available for setup in ad-hoc mode.

TX Power: Transmit power, the amount of power used

by a radio transceiver to send the signal out. User can

choose power value by sliding the bar.

Preamble: There are three types, Auto, Long and Short

are supported.

Ad hoc wireless mode: There are five types. 802.11b

only, 802.11 b/g mix, and 802.11g only modes are

supported.

I. RTS Threshold: User can adjust the RTS threshold

number

directly

by sliding the bar or key in the value

II. Fragment Threshold: User can adjust the RTS

threshold

number by sliding the bar or key in the

value directly.

Channel: Only available for setting under ad-hoc mode.

User can choose the channel frequency to start their

ad-hoc network.

STEP

Authentication & Security setting: Please click Help for

more detail encryption settings.

Click

4.2.2 Ad-hoc Mode

Ad-hoc mode allows your computer to communicate di-

rectly with any computer installed with compatible wire-

less adapter. If you want to use the network in Ad-hoc

mode:

- All the computers connected should be set to

Ad-hoc mode.

- The computers have the same SSID (network

name)setting.

To build the Ad-hoc network:

Click the MSI Wireless LAN icon to bring up the

Wireless Network Connection window. Then, click

Profile tab.

STEP

Click Add.

Click

Set up the Network Name (SSID).

STEP

Check Network Type option and select Ad-hoc mode to

enable the Ad-hoc mode.

STEP

Set the

SSID

Select

Click Authentication and Security to setup Authentica-

tion Type, Encrypation and WPA Pre-shared Key.

STEP

Set the

configuration

for your needs.

>>> 4.3 Link Status

Link Status

Link Status tab displays the detailed information regarding

current connection.

Status: Current connection status. If no connection, if

will show Disconnected. Otherwise, the SSID and

BSSID will show here.

Extra Info: Display link status and current channel in

use.

Link Speed: Show current transmit rate and receive

rate.

Throughout: Display transmits and receive throughput

in unit of K bits/sec.

Link Quality: Display connection quality based on

signal strength and TX/RX packet error rate.

Signal Strength: Receive signal strength, user can

choose to display as percentage or dBm format.

Noise Level: Display noise signal strength.

>>> 4.4 Statistics

Statistics

Statistics tab displays the detailed counter information

based on 802.11 MIB counters. This tab translates MIB

counters into an easier format for users to understand.

Transmit Statistics:

a. Frames Transmitted Successfully: Frames successfully

sent.

b. Frames Transmitted Successfully Without Retry:

Frames successfully sent without any retry.

c. Frames Transmitted Successfully After Retry: Frames

successfully sent with one or more reties.

d. Frames Fail To Receive ACK After All Retries: Frames

failed transmit after hitting retry limit.

e. RTS Frames Successfully Receive CTS:

Successfully receive CTS after sending RTS frame.

f. RTS Frames Fail To Receive CTS: Failed to receive CTS after

sending RTS.

Receive Statistics:

a. Frames Received Successfully: Frames received

successfully.

b. Frames Received With CRC Error: Frames received with

CRC error.

c. Frames Dropped Due To Out-of-Resource: Frames dropped

due to resource issue.

d. Duplicate Frames Received: Duplicate received frames.

Reset counters to zero.

>>> 4.5 About

About tab contains the wireless card and driver version

information.

Connect to MSI website:MSI Technology, Corp.

Display Configuration Utility, drivers, and EEPROM

version.

Display Wireless NIC MAC address.

MSI Software AP Setup

A new way to build your wireless network! The MSI Soft-

ware AP brings a variety of innovations to home network-

ing and small business users that enhance ease-of-use,

set and cost effective.

With this powerful utility, our computer that installed with

the MSI Wireless LAN adapter can become an Access

Point immediately in your office environment, providing a

connection from your wireless network to an existing net-

work backbone, and this allows your wireless clients to

access to the Internet and other resources in your enter-

prise network. It’s ideal for mobile groups (e.g. auditors)

who need short time cost-effective wireless connectivity

without the expense of deploying a hardware-based ac-

cess point.

Wireless11g Turbo G PCICard

To enable the Software AP, right-click the MSI Wireless

LAN icon, and

select “Switch to AP mode”. The MSI Wireless LAN icon

shall change to MSI Software AP icon.

MSI Software AP Icon

Select

STEP

Setting the SSID

SSID (Service Set Indentifier) is the name designated for

a specific wireless local area network ( WLAN).

STEP

Setting the Channel

Channel 1 is the default value. Please note that all de-

vices on the network must share the same channel.

Setting the Authentication and Encryption

Click the button Auth vs. Security to select the Authenti-

cation Type, Encryption Type, and setup the WPA Pre-

shared key.

STEP

If you select Open as your Authentication type, WEP as

Encryption type, you have to setup the WEP Key for your

needs, click OK here. Then back to above screen, click

Apply to complete the configuration.

Set the Authenti-

cation Type,

Encryption Type,

and WPA Pre-

shared Key

Configuring MSI Turbo G

Mode with Client Device

>>> 6.1 Setup

*Experiencing the high throughouput of the MSI Turbo G

mode, MSI Turbo G series wireless products are highly

recommended as your best choices. MSI Turbo G mode

is suggested to function with MSI Turbo G series wire-

less products to optimize performance. The compatibil-

ity of other brands of wireless products with MSI Turbo G

mode is not guaranteed.

(MSI Turbo G Mode support is also required on host/

router side, such as the MSI RG60G).

Actual throughput value might vary due to environmental,

operational and other factors.

STEP

Plug in your Turbo G WLAN Client Device (ex. PC60G,

USB Stick, Cardbus…etc) and follow on-screen setup

steps to finish MSI Wireless Network Card Setup driver

installation.

STEP

Choose MSI Configuration Tool for MSI Utility

configuration.

Select Optimize for performance mode.

STEP

Wait a few seconds until Setup has finished installing.

>>> 6.2 Configuratrion

STEP

To connect MSI Turbo G Router (ex. RG60G), configure

the settings as below:

STEP

>>> 6.3 Confirmation

You may find out whether you’re in Turbo Mode by

checking the following default value.

Make sure both “TxBurst” and “Enable TCP Window

Size” items have been checked, then click “Apply”.

Immediate restart computer is suggested to validate

default value.

STEP

Click

STEP

After all settings had been finished, confirm value of

Frame Aggregation “Enabled” to activate Turbo G mode.

Networking Basics

This chapter describes how to prepare for connection to

network and some basic outline of networking basics,

including sharing files, printing from a computer on the

network, or accessing the Internet on multiple comput-

ers with one connection.

>>> 7.1 Checking the Network Elements

The following elements are required for all computers if

you want to connect to a network:

- Client for Microsoft Network

- TCP/IP

- File and printer sharing for Microsoft Networks

To check the required elements are installed in the system,

you can:

Under Windows 98SE/ME

Click Start and choose Settings; then, click

Control Panel to open the Control Panel

window.

Double-click the Network icon.

The Network window appears to show the

current network settings of the system.

Check the required elements

from this field.

Your Wireless LAN adapter model

Under Windows 2000/XP

Click Start and choose Control Panel to open

the Control Panel window.

Double-click the Network Connection icon to

open the Network Connection window.

Right-click the Wireless Network Connection

icon and click Properties from the shortcut

menu.

The Wireless Network Connection Properties

window appears to show the current network

settings of the system.

Your Wireless LAN adapter model

Check the required

elements from this field.

>>>7.2 Computer Identification

Please verify that each computer has a unique name and

common workgroup name, if you had previously given

your Windows 98SE/ME/2000/XP computers names.

Under Windows 98SE/ME

1. Open the Network window as described in

previous section, and choose Identification tab.

2. Type a name for the computer In the Computer

name box. This will be the name of this com

puter used by other computers on your network

to communicate with. Please NOTE that each

computer’s name must be unique on a

particular network to avoid confusion.

3. Type the workgroup name that the computer will

belong to in the Workgroup box. All the comput-

ers on your network should have an identical

Workgroup name.

4. The Computer Description box is optional. You

may enter a description that helps to identify this

computer on your network. Then, click OK.

5. Repeat the procedure above for each computer

on your network to ensure that they all have

unique Computer Name and identical

Workgroup.

Enter a name for your

computer (less than 15

characters without space.

Your computer will belong to

this workgroup.

Enter some information for

reference.

Under Windows 2000/XP

1. Right-click My Computer icon on your Windows

desktop, and click Properties from the shortcut

menu.

Right-click

Select

2. The System Properties window appears;

choose Computer Name tab.

Enter some information for

reference.

Your computer’s name.

Your computer will belong to

this workgroup.

3. To rename the computer and join a workgroup/

domain, click Change.

4. The Computer Name Changes window appears

as below. Enter a Computer Name, select

Workgroup and enter the name of your

workgroup.

Please NOTE that each computer’s name must

be unique on a particular network to avoid

confusion.

Enter a name for your

computer (less than 15

characters without space.

Enter the name of the

workgroup.

5. Click OK to save changes.

>>> 7.3 Configuring a Dynamic/Fixed IP Address

When the drivers are installed, the default setting here is

set to obtain IP dynamically through a DHCP server. If

you want to change the settings, please follow the steps

below:

Under Windows 98SE/ME

Go to Start -> Settings -> Control Panel.

Double-click the Network icon.

The Network window appears as below. Select

TCP/IP -> (your Wireless LAN adapter model),

and click Properties to bring up the TCP/IP

Properties window.

Your Wireless LAN adapter model

Select this

Click

4.a To configure a dynamic IP address, choose IP

Address tab and check the Obtain an IP

Address Automatically option.

4.b

To configure a fixed IP address, choose IP

Address tab and check the Specify an IP

Address option.

Then, enter an IP address into the empty field.

Suggested IP Address Range is 192.168.1.1 to

192.168.1.253, and suggested Subnet Mask is

255.255.255.0.

Check this

4.a Configuring a dynamic IP address

Check this

Enter a fixed IP address

and Subnet Mask

4.b Configuring a fixed IP address

Click OK. Then, click Yes when prompted to

reboot the computer.

Under Windows 2000/XP

Click Start and choose Control Panel to open

the Control Panel window.

Double-click the Network Connection icon to

open the Network Connection window.

Right-click the IEEE802.11g Wireless PCI

Adapter icon and click Properties from the

shortcut menu.

When the Wireless Network Connection

Properties window appears, choose General

tab and select Internet Protocol [TCP/IP], and

click Properties to bring up the Internet Proto

col [TCP/IP] Properties window.

Your Wireless LAN adapter model

Select this

Click

5.a To configure a dynamic IP address, check the

Obtain an IP Address Automatically option.

5.b To configure a fixed IP address, check the Use

the following IP address option. Then, enter an

IP address into the empty field. Suggested IP

Address Range is 192.168.1.1 to 192.168.1.

253, and suggested Subnet Mask is 255.255.

255.0.

Check this

5.a Configuring a dynamic IP address

Check this

Enter a fixed IP address

and Subnet Mask

5.b Configuring a fixed IP address

Click OK to complete the configuration.

>>> 7.4 Checking TCP/IP Address

Under Windows 98SE/ME

Go to Start -> Run....

Type winipcfg in the Open box and click OK.

Type winipcfg here.

The IP Configuration screen will appear, click

More Info to bring up a screen containing detail

information of your wireless network adapter.

Your Wireless LAN adapter model

Check the configuration of

IP Address, Subnet Mask,

and Default Gateway are

correct.

Under Windows 2000/XP

Go to Start -> Run....

Type cmd in the Open box and click OK.

Type cmd here.

A DOS prompt window appears. Type ipconfig/

all and press [Enter] to display IP information.

Your Wireless LAN adapter model

Check the configuration of

IP Address, Subnet Mask,

and Default Gateway are

correct.

>>> 7.5 Checking Connection by Pinging

Go to Start -> Run....

Type command (Windows 98SE/ME) or cmd

(Windows 2000/XP) in the Open box and click

OK.

A DOS prompt window appears. Type ping 210.

59.147.160 (or any URL address), which is the

IP address of the Gateway in this case, and

press [Enter].

You will get reply if the

pinging is successful.

>>> 7.6 Sharing Files

You may now open and save files on other computers

once your computers are connected together on a

network. You will also be able to specify particular fold-

ers or disk drives to share and even password to protect

them. Please verify that each computer has a unique

name and common workgroup name, if you had previ-

ously given your Windows^®98SE/ME/2000/XP comput-

ers names. Follow the steps below to share specific

files and folders with other computers on your network.

On your Windows desktop, right-click My

Network Place icon and select Properties from

the shortcut menu.

You will configure your computers network

settings in this dialog. It is also available

through the Networkicon in the Control Panel.

Click the File and Print Sharing option.

Your Wireless LAN adapter model

Click

4. Select the I want to be able to give others

access to my files option, and click OK.

Check this

Click

Click OK in the Network dialog box.

Provide the Windows Setup CD or direct the

path tothe proper location of the installation files

if prompted. Then, reboot if prompted.

Now you can identify a particular folder or disk

drive to share, which means you can share a

folder that both you and your family member/

colleague needs to access occasionally. You

can also share your CD-ROM drive for others to

use if your other computers do not have one.

Both of these processes are the same. Only the

disk drives and folders that you specifically

identify as shared will be accessible to other

computers on your network.

Locate the disk drive or folder you want to share

in Windows Explore or My Computer icon on

your desktop.

Right-click the disk drive or folder and select

Sharing.

10. Select the Share As option to set the param

eters for sharing this particular disk drive or

folder.

Share Name

This is used to identify the disk drive or folder you are

sharing to other computers in the network, which can be

helpful as more resources in your network for others.

Comment

This field is optional, which can be used to further de-

scribe the disk drive or folder for others in the network.

Access Type

This option allows you to designate how much someone

else can do with this shared disk drive or folder. Setting

options are:

- Read-Only: only allows others to look at or

open the files in the disk drive or folder.

- Full: allows others to read, write, open, save,

copy, move, and even delete files.

- Depends on Password: gives other computers

access conditional on the password they

provide.

Password

This option allows you to apply a level of security to your

shared disk drive and folder. Any other computer (user)

will be asked to enter the password you set here before

accessing the disk drive or folder. Two passwords are

used to give two levels of security (or access) to others in

the network using the Depends on Password setting.

Leaving the Password boxes empty will give everyone in

the network access to the disk drive or folder.

11. Click OK to continue. You will be prompted to

type the password(s) you provided for

verification. Type the password(s) just as you

typed them again.

12. Now you may access this disk drive or folder

from another computer in your network. You

may do so by double-clicking the My Network

Place icon on your Windows desktop or inside

Windows Explorer.

13. Navigate to the computer with the shared disk

drive or folder (recognized by the Computer

Name you provided), and double-click it. If you

specified a password when sharing this disk

drive or folder, you will be asked for the

password.

14. You can access a disk drive of folder shared

over the network from most Windows 98SE/ME/

2000/XP applications. you can map these disk

drives and folders to a drive letter on another

computer to make this process easier. For

example, on a computer where you are access

ing a shared folder from another computer,

inside Windows Explorer right-click and

select the Map Network Drive option. Now you

are able to assign an available drive letter.

Checking the Reconnect at logon option allows

Windows to map this network drive each time

when you start your computer.

Trouble Shooting

I can’t connect to the Internet wirelessly?

If you are unable to connect to the Internet from a wire-

less computer, please check the following item:

1. Look at the lights on your Wireless Router.

The “Power” light should be on.

The “Connected” light should be on, and not

blinking.

The “WAN” light should be either on or blinking.

If your Wireless Router’s lights have the above

characteristics, go to number 2 below.

If this is NOT the case, make sure:

-The Router power cord is plugged in.

-All cables are connected between the router and

the modem.

-All the modem’s LEDs are function correctly. If

not, see your modem’s user manual.

-Reboot the Modem.

If above problems continued, please consult the router

user guide supplied by manufacturers.

2. Open your wireless utility software by clicking on the

icon in the system tray at the bottom right-hand corner of

the screen. If you’re using this MSI PC60G Wireless 11g

Turbo G PCI Card, the icon in the system tray should look

like the one below.

Please note: The MSI Wireless Utillity icon shall appear a

red cross when disconnected.

3. The exact screen shall vary depending on the model of wire-

less card you have at hand; however, any of the utilities shall

have a list of ”Site Surveys” or “ Available Networks”. Site Sur-

veys” or “ Available Networks” are available wireless networks

you are able to connect to.

Installation CD-ROM does not start Setup Utility?

If the CD-ROM does not start the Setup Utility automatically, one

of the possible reasons might be system is running other ap-

plications that are interferring with the CD drive.

If the Setup Utility does not appear within 15-20 seconds, click

Start at the taskbar and select Run.... Type E:\setup.exe (where

E is your CD-drive) in the Open box and click OK to launch the

Setup program manually.

Power LED does not ON; Card is not working

If the LED indicators are not ON, the problem might be that the

card is not connected or is not properly installed.

Verify that the card is plugged firmly into the PCI slot of your

computer. Check to see that the necessory drivers for the card

have been installed. Right click on the My Computer icon on

your desktop. Chosse Properties and navigate to the Device

Manager and see if your PCI card is listed without any errors.

Please contact us for any errors.

Data transfering is slow sometimes.

Wireless Technologh is radio-based, which means connectiv-

ity and the throughput performance between devices decrease

when the distance between devices increases. Other possible

factors that cause signal degradation are obstructions such as

walls and applicances made of metal. Consequently, the typi-

cal indoor range of your wireless devices will be between 100

to 200 feet of range. Note that connection speed may decrease

as you move further from the wireless router or access point.

In order to determine if wireless issues are related to distance

range, moving computer for the moment is highly suggested.

Usually 5 to 10 feet from the wireless router (or access ppoint) is

recommended if possible. Please contact us for technical suport

if issues persist even at a close range.

Poor signal strength

Due to above mentioned features regarding wireless technol-

ogy in question 4. Changing the wireless channel - depending

on local wireless traffic and interference, switching the wireless

channel of your network can inmprove performance and reliability.

The default channel the router is shipped with is channel 11, you

may choose from several other channels by your region. See yor

router manual for instructions on how to choose other channels.

Limiting the wireless transmit rate - Limiting the wireless trans-

mit rate can help to improve the maximun wireless range as well

as connection stability. Most wireless cards are equipped with

function of limit the transmission rate. To change this property,

go to the Windows Control Panel, open the Network Connec-

tions and double-click on your wireless card’s connection. In the

properties dialog, select the Configure button on the General tab

(Windows 98 users will have to select the wireless card in the

list box and then click Properties), then choose the Advanced tab

and select the Rate Property. Wireless client cards are usually

set to automatically adjust the wireless transmit rate, however

doing so could cause periodic disconnections at weak wireless

signals. Under such circumstances, slower transmission rate

would be more stable. Try different connection rate until you find

the best one for your environment. Note that all available trans-

mission rate shall be accessible browsing internet. For more

details, see documents attached with your wireless card.

Why are there two wireless utilities in my system tray and

which one am I supposed to use?

There are several features and advantages from using the

Ralink wireless utility over the Windows XP Wireless Zero Con-

figuration utility. We do offer a site survey, detailed link informa-

tion and adapter diagosis, to name a few.

It is essential to know which utility manages your adaper. In

this case, Ralink wireless utility application is suggested to

apply.

To use the Ralink wireless utility, follow steps below:

Step 1: Right-click on the network status icon in the system tray

and select View Available Wireless Networks.

Step 2: Click on the Advanced button in the lower-left corner of

the Available Wireless Networks window.

Step 3: From the Advanced tab, uncheck Use Windows to con-

figure my wireless network. Once the box is unchecked, click

OK to close the window.

You are now using the Ralink wireless utility to configure the

wireless card.

Wireless 11g Turbo G PCI Card is not detected by operating

system.

The Wireless 11g Turbo G PCI Card is not recognized by your

desktop computer.

The “New Hardware” Wizard does not appear when booting up

the computer.

^´Receive Microsoft Error Code: 10

^´Receive Microsoft Error Code: 0

If the “New Hardware Wizard” does not appear, or you receive

any of the above error codes, please try following troubleshoot-

ing steps:

1. Remove the screws behind your computer case that

secures the computer cover and remove cover.

2. Touch any metal part of the case to discharge static

electricity, which may damage your device or your

computer.

3. Remove the Wireless 11g Turbo G PCI card.

4. Locate a different empty PCI expansion slot. The slot is

usually white.

5. Confirm the card should fit into the slot you have

choosen.

Keep in mind that the included antenna needs to be ori-

ented with the top pointing up. If there are cables and other

connections in the way, try to pick the PCI slot that has the

least obstructions to the correct the positioning of the

antenna.

6. Remove the metal port cover from the back of the

computer that corresponds to the selected PCI slot.

Place the screws in a safe place if there are any, as you

may need them later to attach the card to the computer.

7. Push the card firmly into the selected PCI slot, until the

connector is fully seated.

8. Now secure the card with the screw mentioned on Step 6.

9. Carefully screw the antenna onto the threaded connector

on the card. Turn the antenna till it is vertical and pointing

up.

10. Replace cover of the computer. Since the card is

installed, you can reconnect the porwer cord, and power

on the system.

11. The card should be identified by the computer now.

CE Compliance

Booklet

Table of Content

English........................................................................... 1

Detusch ......................................................................... 2

Français......................................................................... 3

Čeština........................................................................... 4

Dansk............................................................................. 5

Nederlands.................................................................... 6

Eesti............................................................................... 7

SUOMEKSI .................................................................... 8

Ελληνικάη...................................................................... 9

Magyar........................................................................... 10

Italiano........................................................................... 11

Latviska......................................................................... 12

Lietuvių.......................................................................... 13

Malti ............................................................................... 14

Polski............................................................................. 15

Português...................................................................... 16

Slovensky...................................................................... 17

Slovenèina..................................................................... 18

Español.......................................................................... 19

SVENSKA ...................................................................... 20

English

Hereby, Micro Star International CO., LTD declares that this device is in compliance with the essential

requirements and other relevant provisions of Directive 1999/5/EC. The respective Declaration of conformity

can be found online:

http://www.msi-computer.de/support/dl_man.php

IEEE 802.11b/g and Bluetoothâ 2.4 GHz operation

Europe: Frequencies: 2.400 – 2.4835 GHz

France: Frequencies: 2.4465– 2.4835 GHz,

Outdoor use is limited to 10mW e.i.r.p. within the band 2454-2483.5 MHz

Italy:

If used outside of own premises, general authorisation is required.

Luxembourg:

General authorisation required for public service.

Notified Countries:

Germany, UK, Netherlands, Belgium, Sweden, Denmark, Finland, France, Italy, Spain, Austria, Ireland,

Portugal, Greece, Luxembourg, Estonia, Letvia, Lithuania, Czech Republic, Slovakia , Slovenia, Hungary,

Poland und Malta.

Prescribed use:

This product integrates a WLAN- and/or Bluetoothâ device.

The device sets up a radio link between to computer. In addition it is possible to link the WLAN- or Bluetoothâ

device to any other WLAN- or Bluetoothâ device which stick to the IEEE 802.11b/g or Bluetoothâ

requirements.

Operating range:

The transmission range between different WLAN- or Bluetoothâ devices varies depending the specific

environment. Walls, concrete floor (iron), laminated windows, vehicle-body, etc..

More electromagnetic interferences:

- high frequency emission of any kind,

- Buildings, trees, etc.

- Heaters, ferroconcrete, etc.

- open computer systems, etc.

- Microwave oven, etc,

Communication (exchange data) is dependent on the software of the WLAN or Bluetoothâ devices.

Deutsch

Hiermit erklärt Micro Star International CO., LTD dass sich dieses Produkt in Übereinstimmung mit den

grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet.

Die Konformitätserklärung kann auf folgender website eingesehen werden:

http://www.msi-computer.de/support/dl_man.php

IEEE 802.11b/g und Bluetoothâ 2.4 GHz Betrieb

Europa: Frequenzen: 2.400 – 2.4835 GHz

Frankreich: Frequenzen: 2.4465– 2.4835 GHz,

Außerhalb von geschlossenen Gebäuden ist die genehmigte Sendeleistung im Frequenzband 2454-2483.5

MHz auf maximal 10mW beschränkt.

Italy:

If used outside of own premises, general authorisation is required.

Luxembourg:

General authorisation required for public service.

Notified Countries:

Germany, UK, Netherlands, Belgium, Sweden, Denmark, Finland, France, Italy, Spain, Austria, Ireland,

Portugal, Greece, Luxembourg, Estonia, Letvia, Lithuania, Czech Republic, Slovakia , Slovenia, Hungary,

Poland und Malta.

Bestimmungsgemäße Verwendung:

Dieses Produkt integriert als Teil der Produktausstattung eine WLAN-Komponente und/oder eine Bluetoothâ -

Komponente.

Die entsprechende Komponente verbindet Computer über eine Funkverbindung . Es kann auch eine

Funkverbindung zu anderen geeigneten WLAN- oder Bluetoothâ Geräten hergestellt werden.

Hinweise zur Reichweite:

Der Abstand zwischen Sender und Empfänger (von einem WLAN- oder Bluetoothâ -Gerät zu einem

entsprechenden anderen Gerät) hängt stark von der Einsatzumgebung ab. Wände, Betonboden (Eisen),

beschichtete Fensterscheiben, Fahrzeug-Karosserie, etc..

Weitere Beeinflussungen:

- Hochfrequenzaussendungen jeder Art

- Gebäude, Bäume, etc.

- Heizkörper, Stahlbeton, etc.

- offen betriebene Computer, etc.

- Mikrowellenherde, etc,

Die Kommunikation zwischen unterschiedlichen WLAN- oder Bluetoothâ -Geräten ist von der jeweiligen

Software und dem entsprechenden Versionsstand abhängig

MSI Technology GmbH. Frankfurt a. M.

Français

Par la présente, Micro Star International CO., LTD, déclare que ce dispositif est conforme aux conditions

essentielles et autres dispositions appropriées à la directive 1999/5/EC. La déclaration concernant la

conformité peut être trouvée en ligne :

http://www.msi-computer.de/support/dl_man.php

IEEE 802.11b/g and Bluetoothâ 2.4 GHz

Europe: Fréquences: 2.400 – 2.4835 GHz

France: Fréquences: 2.4465– 2.4835 GHz,

L’utilisation à l’extérieur est limitée à 10 Mw dans la bande passante 2454 à 2483.5 MH

Italy:

Pour une utilisation hors de ses propres lieux, une autorisation générale est requise.

Luxembourg:

Une autorisation générale est requise pour le service public.

Pays concernés

Germany, UK, Netherlands, Belgium, Sweden, Denmark, Finland, France, Italy, Spain, Austria, Ireland,

Portugal, Greece, Luxembourg, Estonia, Letvia, Lithuania, Czech Republic, Slovakia , Slovenia, Hungary,

Poland und Malta.

Utilisation prescrite

Le produit intègre un dispositif WLAN- et/ou Bluetoothâ .

Le dispositif établit un lien radio avec l’ordinateur. De plus, il est possible de relier le dispositif WLAN – ou

Bluetoothâ à tout autre dispositif WLAN - ou Bluetoothâ correspondant aux exigences du Bluetoothâ .

Plage de fonctionnement

La plage de fonctionnement entre différents dispositifs WLAN ou Bluetoothâ varie selon l’environnement.

Murs, planchers en béton, fenêtres laminées, intérieur d’un véhicule.

Plus d’interférences électromagnétiques:

- Emission haute fréquence de toutes sortes

- Bâtiments, arbres, etc.

- Chauffage, bétons armés, etc.

- boîtier d’ordinateur non fermé.

- Micro-ondes, etc.

La communication (échange des données) dépend du logiciel des dispositifs WLAN ou Bluetoothâ .

Čeština

Společnost Micro Star International CO., LTD tímto prohlašuje, že toto zařízení splňuje základní požadavky a

další odpovídající ustanovení směrnice 1999/5/EC. Příslušné prohlášení o shodě je k dispozici online:

http://www.msi-computer.de/support/dl_man.php

Provozování bezdrátové komunikace standardu IEEE 802.11b/g a Bluetoothâ 2,4 GHz:

Evropa: frekvence: 2,400 – 2,4835 GHz

Francie: frekvence: 2,4465– 2,4835 GHz,

vnější provozování je omezeno na 10mW e.i.r.p. v pásmu 2454 – 2483,5 MHz.

Italy:

K vnějšímu provozování na vlastních pozemcích je vyžadováno oprávnění.

Luxembourg:

K veřejným službám je vyžadováno obecné oprávnění.

Uvedené země:

Germany, UK, Netherlands, Belgium, Sweden, Denmark, Finland, France, Italy, Spain, Austria, Ireland,

Portugal, Greece, Luxembourg, Estonia, Letvia, Lithuania, Czech Republic, Slovakia , Slovenia, Hungary,

Poland und Malta.

Předepsané použití:

V tomto výrobku je integrováno zařízení WLAN- a/nebo Bluetoothâ .

Toto zařízení navazuje rádiové spojení s počítačem. Navíc je toto zařízení WLAN- nebo Bluetoothâ možné

připojit k libovolnému jinému zařízení WLAN- nebo Bluetoothâ , které splňuje požadavky standardu IEEE

802.11b/g nebo Bluetoothâ .

Provozní dosah:

Přenosový dosah mezi různými zařízeními WLAN- nebo Bluetoothâ se liší v závislosti na konkrétním

prostředí. Stěny, (železo)betonová podlaha, laminovaná okna, karosérie vozidla, atd.

Další zdroje elektromagnetického rušení:

- vysokofrekvenční emise jakéhokoli druhu,

- budovy, stromy atd.

- topidla, železobeton atd.

- otevřené počítačové systémy atd.

- mikrovlnná trouba atd.

Komunikace (výměna dat) závisí na softwaru zařízení WLAN nebo Bluetoothâ .

Dansk

Micro Star International CO., LTD erklærer hermed at denne enhed overholder de væsentlige krav og andre

relevante bestemmelser i direktiv 1999/5/EC. De respektive overbestemmelsesdeklarationer kan findes online:

http://www.msi-computer.de/support/dl_man.php

IEEE 802.11b/g og Bluetoothâ 2.4 GHz operation

Europa: Frekvenser: 2.400 – 2.4835 GHz

Frankrig: Frekvenser: 2.4465– 2.4835 GHz,

Udendørs brug er begrænset til 10mW e.i.r.p. inden for bånd 2454-2483.5 MHz

Italy:

Hvis anvendt uden for egen grund er general autorisation påkrævet.

Luxembourg:

General autorisation påkrævet for offentlig service.

Berørte lande:

Germany, UK, Netherlands, Belgium, Sweden, Denmark, Finland, France, Italy, Spain, Austria, Ireland,

Portugal, Greece, Luxembourg, Estonia, Letvia, Lithuania, Czech Republic, Slovakia , Slovenia, Hungary,

Poland und Malta.

Reglementeret brug:

Dette produkt integrere en WLAN- og/eller Bluetoothâ enhed.

Denne enhed etablere en radioforbindelse mellem to computere. Yderligere er det muligt at forbinde WLAN-

eller Bluetoothâ enheden til en hvilken som helst anden WLAN- eller Bluetoothâ enhed der overholder IEEE

802.11b/g eller Bluetoothâ kravene.

Driftsrækkevidde:

Transmissionsrækkevidden mellem forskellige WLAN- eller Bluetoothâ enheder varierer afhængig af de

specifikke omgivelser. Vægge, betongulve (jern), splintfri glas, køretøjer, osv.

Andre elektromagnetiske forstyrrelser:

- højfrekvens udsendelse af enhver art,

- Bygninger, træer, osv.

- Varmekilder, jernbeton, osv.

- Åbne computersystemer, osv.

- Mikroovne, osv,

Kommunikation (dataudveksling) er afhængig af softwaren til WLAN eller Bluetoothâ enhederne.

Nederlands

Hierbij verklaart Micro Star International CO., LTD dat dit apparaat voldoet aan de eisen en andere relevante

maatstaven van de Directive 1999/5/EC.

De respectievelijke verklaring van conformiteit kan online gevonden worden:

http://www.msi-computer.de/support/dl_man.php

IEEE 802.11b/g en Bluetoothâ 2.4 GHz werking

Europa: Frequenties: 2.400 – 2.4835 GHz

Frankrijk: Frequenties: 2.4465– 2.4835 GHz,

Buitengebruik is gelimiteerd tot 10mW EIRP (Effective Isotropic Radiated Power) binnen de breedte van

2454-2483.5 MHz

Italië:

Bij gebruik buiten eigen pand, is algemene autorisatie vereist.

Luxemburg:

Algemene autorisatie is vereist voor publieke service.

Aangekondigde Landen:

Germany, UK, Netherlands, Belgium, Sweden, Denmark, Finland, France, Italy, Spain, Austria, Ireland,

Portugal, Greece, Luxembourg, Estonia, Letvia, Lithuania, Czech Republic, Slovakia , Slovenia, Hungary,

Poland und Malta.

Voorgeschreven gebruik:

Dit product is een WLAN- en/of Bluetoothâ apparaat.

Dit apparaat maakt een “radio verbinding” met de computer.

Daarnaast is het mogelijk om het WLAN- of Bluetoothâ apparaat te linken aan andere WLAN- of Bluetoothâ

apparaten die voldoen aan de IEEE 802.11b/g of Bluetoothâ vereisten.

Bereik:

De transmissie range tussen verschillende WLAN- of Bluetoothâ apparaten varieert afhankelijk van de

specifieke omgevingen.

- Muren, beton, vitrage, carrosserieën etc..

- Meer electromagnetische storingen:

- Hoge frequentie afgifte van ieder soort,

- Gebouwen, bomen, etc. etc.

- Verwarmingen, gewapend beton, etc.

- Open computer systemen, etc.

- Magnetron-oven, etc,

Communicatie (uitwisselen van data) hangt af van de software van het WLAN of Bluetoothâ apparaat.

Eesti

Siinkohal teatab Micro Star International CO., LTD, et käesolev seade vastab direktiivi Directive 1999/5/EC

põhinõuetele ning muudele olulistele sätetele. Sellekohase vastavusdeklaratsiooni võib leida aadressil:

http://www.msi-computer.de/support/dl_man.php

IEEE 802.11b/g ja Bluetoothâ 2,4 GHz töö

Euroopa: sagedused: 2,400 – 2,4835 GHz

Prantsusmaa: sagedused: 2,4465 – 2,4835 GHz

Kasutamine välistingimustes piiratud võimsusega 10mW, st sagedusriba 2454-2483,5 MHz piires

Italy:

Kasutamisel väljaspool oma territooriumi on vajalik üldine kasutusluba.

Luxembourg:

Avalikuks kasutamiseks vajalik üldine kasutusluba.

Teavitatud riigid:

Germany, UK, Netherlands, Belgium, Sweden, Denmark, Finland, France, Italy, Spain, Austria, Ireland,

Portugal, Greece, Luxembourg, Estonia, Letvia, Lithuania, Czech Republic, Slovakia , Slovenia, Hungary,

Poland und Malta.

Ettenähtud kasutamine:

See toode integreerib WLAN- ja/või Bluetoothâ -seadme.

Seade loob raadiolingi arvutiga. Lisaks on võimalik ühendada WLAN- või Bluetoothâ -seade mis tahes teise

WLAN- või Bluetoothâ -seadmega, mis vastab IEEE 802.11b/g või Bluetoothâ -standardi nõuetele.

Tööulatus:

Tööulatus erinevate WLAN- või Bluetoothâ -seadmete vahel varieerub olenevalt konkreetsest keskkonnast.

Seinad, betoonpõrand (raud), mitmekihilised aknad, sõiduki kere jne.

Täiendavad elektromagnetilised häiringud:

- igat liiki kõrgsageduskiirgus,

- ehitised, puud jne,

- kütteseadmed, raudbetoon jne,

- avatud arvutisüsteemid jne,

- mikrolaineahjud jne.

Side (andmevahetus) oleneb WLAN- või Bluetoothâ -seadmete tarkvarast.

SUOMEKSI

Täten Micro Star International CO., LTD vakuuttaa, että tämä laite on yhdenmukainen direktiivin 1999/5/EC

olennaisten vaatimusten ja muiden asianmukaisten säädösten kanssa. Vastaava yhdenmukaisuusselvitys on

nähtävillä Internetissä osoitteessa:

http://www.msi-computer.de/support/dl_man.php

IEEE 802.11b/g:n ja Bluetoothâ 2.4 GHz:n käyttö

Eurooppa: Taajuudet: 2.400 – 2.4835 GHz

Ranska: Taajuudet: 2.4465– 2.4835 GHz,

Ulkokäyttö on rajoitettu 10mW e.i.r.p.:een 2454-2483.5 MHz kaistalla.

Italy:

Jos käytetään omien toimitilojen ulkopuolella, tarvitaan yleinen valtuutus.

Luxembourg:

Tarvitaan yleinen valtuutus julkista palvelua varten.

Ilmoitetut maat:

Germany, UK, Netherlands, Belgium, Sweden, Denmark, Finland, France, Italy, Spain, Austria, Ireland,

Portugal, Greece, Luxembourg, Estonia, Letvia, Lithuania, Czech Republic, Slovakia , Slovenia, Hungary,

Poland und Malta.

Määräystenmukainen käyttö:

Tämä tuote integroi WLAN- ja/tai Bluetoothâ -laitteet.

Laite luo radiolinkin tietokoneen välille. Lisäksi WLAN- tai Bluetoothâ -laite voidaan linkittää mihin tahansa

toiseen WLAN- tai Bluetoothâ -laitteeseen, joka vastaa IEEE 802.11b/g- tai Bluetoothâ -vaatimuksia.

Toiminta-alue:

Erilaisten WLAN- ja Bluetoothâ -laitteiden lähetyksen kantama vaihtelee ympäristöstä riippuen. Seinät,

betonilattia (rauta), laminaatti-ikkunat, ajoneuvon runko, jne.

Lisää sähkömagneettista häiriötä:

- mikä tahansa korkeataajuinen säteily,

- rakennukset, puut, jne.

- lämmitin, teräsbetoni, jne.

- avoimet tietokonejärjestelmät, jne.

- mikroaaltouuni, jne.

Tietojen vaihto riippuu WLAN- tai Bluetoothâ -laitteiden ohjelmistoista.

Ελληνικάη

Με το παρόν, η Micro Star International CO., LTD δηλώνει πως αυτή η συσκευή συμμορφώνεται με τις

θεμελιώδεις απαιτήσεις και τις άλλες σχετικές διατάξεις της Οδηγίας 1999/5/EΚ. Η σχετική Δήλωση

συμμόρφωσης μπορεί να βρεθεί στη διεύθυνση:

http://www.msi-computer.de/support/dl_man.php

IEEE λειτουργία 802.11b/g και Bluetoothâ 2.4 GHz

Ευρώπη: Συχνότητες: 2.400 – 2.4835 GHz

Γαλλία: Συχνότητες: 2.4465– 2.4835 GHz,

Η χρήση σε εξωτερικούς χώρους περιορίζεται σε 10mW e.i.r.p. στη συχνότητα 2454-2483.5 MHz

Italy:

Αν χρησιμοποιείται εκτός των ιδιωτικών χώρων, απαιτείται γενική εξουσιοδότηση.

Luxembourg:

Απαιτείται γενική εξουσιοδότηση για δημόσια υπηρεσία.

Χώρες που έχουν ειδοποιηθεί:

Germany, UK, Netherlands, Belgium, Sweden, Denmark, Finland, France, Italy, Spain, Austria, Ireland,

Portugal, Greece, Luxembourg, Estonia, Letvia, Lithuania, Czech Republic, Slovakia , Slovenia, Hungary,

Poland und Malta.

Συνιστούμενη χρήση:

Αυτό το προϊόν ενσωματώνει μια συσκευή WLAN- και/ή Bluetoothâ .

Η συσκευή δημιουργεί μια ραδιοφωνική σύνδεση μεταξύ υπολογιστών. Επιπλέον, είναι δυνατόν να συνδέσετε

τη συσκευή WLAN- ή Bluetoothâ σε οποιαδήποτε άλλη συσκευή WLAN- ή Bluetoothâ η οποία

συμμορφώνεται με τις απαιτήσεις IEEE 802.11b/g ή Bluetoothâ .

Εύρος λειτουργίας:

Το εύρος μετάδοσης ανάμεσα σε διαφορετικές συσκευές WLAN- ή Bluetoothâ ποικίλει ανάλογα με το

συγκεκριμένο περιβάλλον. Τοίχοι, συμπαγές πάτωμα (σίδερο), παράθυρα αλουμινίου, πλαίσιο οχήματος, κτλ.

Περισσότερες ηλεκτρομαγνητικές παρεμβολές:

- εκπομπή οποιουδήποτε είδους υψηλής συχνότητας,

- Κτίρια, δέντρα, κτλ.

- Καλοριφέρ, μπετόν-αρμέ, κτλ.

- αναμμένα συστήματα υπολογιστών, κτλ.

- Φούρνος μικροκυμάτων, κτλ,

Η επικοινωνία (ανταλλαγή δεδομένων) εξαρτάται από το λογισμικό των συσκευών WLAN ή Bluetoothâ .

Magyar

Ezennel, a Micro Star International CO., LTD kijelenti, hogy ez az eszköz megfelel az 1999/5/EK Irányelv

lényeges és egyéb releváns előírásainak. A vonatkozó Megfelelőségi Nyilatkozat megtelálható a következő

címen:

http://www.msi-computer.de/support/dl_man.php

IEEE 802,11b/g és Bluetoothâ 2,4 GHz üzemeltetés

Európa: Frekvenciák: 2,400 – 2,4835 GHz

Franciaország: Frekvenciák: 2,4465 – 2,4835 GHz,

A kültéri használat 10mW e.i.r.p. értékre korlátozott a 2454-2483,5 MHz sávban

Italy:

Amennyiben saját tulajdonú területen kívül használják, általános engedélyezés szükséges.

Luxembourg:

Általános engedélyezés szükséges nyilvános szolgáltatás esetén.

Bejelentett országok:

Germany, UK, Netherlands, Belgium, Sweden, Denmark, Finland, France, Italy, Spain, Austria, Ireland,

Portugal, Greece, Luxembourg, Estonia, Letvia, Lithuania, Czech Republic, Slovakia , Slovenia, Hungary,

Poland und Malta.

Előírt használat:

Ez a termék integrál egy WLAN- és/vagy Bluetoothâ eszközt.

Az eszköz rádiókapcsolatot hoz létre két számítógép között. Ezen kívül, lehetséges összekapcsolni a WLAN-

vagy Bluetoothâ eszközt, bármilyen egyéb WLAN- vagy Bluetoothâ eszközzel amely megfelel az IEEE

802.11b/g vagy Bluetoothâ követelményeknek.

Üzemelési tartomány:

A sugárzási tartomány különböző WLAN- vagy Bluetoothâ eszközök között, függ az adott környezettől. Falak,

betonpadló (vas), réteges ablakok, jármű alváza, stb.

Elektromágneses zavarás:

- bármilyen fajta magas frekvenciájú sugárzás,

- épületek, fák, stb.

- fűtőtestek, vasbeton, stb.

- nyitott számítógéprendszerek, stb.

- mikrohullámú sütő, stb.

A kommunikáció (adatforgalom) függ a szoftvertől amelyek a WLAN vagy Bluetoothâ eszközöket működtetik.

Italiano

Con il presente, Micro Star International CO., LTD dichiara che la periferica è conforme alle principali richieste

e ai più importanti provvedimenti della direttiva

1999/5/EC. La corrispondente Dichiarazione di conformità può essere trovata online:

http://www.msi-computer.de/support/dl_man.php

Funzionamento IEEE 802.11b/g e Bluetoothâ 2.4 GHz

Europa: Frequenze: 2.400 – 2.4835 GHz

Francia: Frequenze: 2.4465– 2.4835 GHz,

L’uso in ambiente aperto è limitato a 10mW e.i.r.p. entro la banda 2454-2483.5 MHz

Italy:

Se si utilizza al di fuori della propria proprietà, è richiesta un’autorizzazione.

Luxembourg:

È necessaria un’autorizzazione per l’utilizzo in pubblico.

Paesi notificati:

Germany, UK, Netherlands, Belgium, Sweden, Denmark, Finland, France, Italy, Spain, Austria, Ireland,

Portugal, Greece, Luxembourg, Estonia, Letvia, Lithuania, Czech Republic, Slovakia , Slovenia, Hungary,

Poland und Malta.

Uso prescritto:

Questo prodotto integra una periferica WLAN- e/o Bluetoothâ .

La periferica genera un collegamento radio al computer. Inoltre è possibile collegare la periferica WLAN- o

Bluetoothâ a ogni altra periferica WLAN- o Bluetoothâ che soddisfi le richieste IEEE 802.11b/g o Bluetoothâ .

Range di funzionamento:

La portata di trasmissione tra differenti periferiche WLAN- o Bluetoothâ varia in funzione di specifiche

condizioni ambientali. Muri, pavimenti in calcestruzzo, finestre laminate, la struttura del veicolo, ecc..

Maggiori interferenze elettromagnetiche:

- Emissioni ad alta frequenza di ogni tipo,

- Edifici, alberi, ecc.

- Caloriferi, cemento armato, ecc.

- Computer aperti, ecc.

- Forni a microonde, ecc,

La comunicazione (scambio di dati) dipende dal software delle periferiche WLAN o Bluetoothâ .

Latviska

Ar šo Micro Star International CO., LTD paziņo, ka šī ierīce atbilst direktīvas 1999/5/EK pamata prasībām un

citiem saistītiem noteikumiem. Attiecīgā atbilstības deklarācija ir atrodama tiešsaistē:

http://www.msi-computer.de/support/dl_man.php

IEEE 802.11b/g un Bluetoothâ 2.4 GHz darbība

Eiropa: Frekvences: 2.400 – 2.4835 GHz

Francija: Frekvences: 2.4465– 2.4835 GHz,

Ārpustelpu lietošana ir ierobežota līdz 10 mW e.i.r.p. frekvenču joslā 2454-2483.5 MHz

Italy:

Lietojot ārpus mūsu telpām, nepieciešama vispārēja atļauja.

Luxembourg:

Vispārēja atļauja nepieciešama publiskai apkalpošanai.

Informētās valstis:

Germany, UK, Netherlands, Belgium, Sweden, Denmark, Finland, France, Italy, Spain, Austria, Ireland,

Portugal, Greece, Luxembourg, Estonia, Letvia, Lithuania, Czech Republic, Slovakia , Slovenia, Hungary,

Poland und Malta.

Paredzētā lietošana:

Šis produkts apvieno WLAN- un/vai Bluetoothâ ierīci.

Šī ierīce izveido radio saiti ar datoru. Papildus ir iespējams WLAN- vai Bluetoothâ ierīci saistīt ar jebkuru citu

WLAN- vai Bluetoothâ ierīci, kas atbilst IEEE 802.11b/g vai Bluetoothâ prasībām.

Darbības diapazons:

Pārraides diapazons starp dažādām WLAN- vai Bluetoothâ ierīcēm mainās atkarībā no konkrētās vides -

sienas, cementa grīda (dzelzs), lamināta logi, automašīnas korpuss u.c.

Lielāka elektromagnētiskā interference:

- jebkura veida augstfrekvences starojums

- ēkas, koki u.c.

- sildķermeņi, dzelzsbetons u.c.

- atvērtas datorsistēmas u.c.

- mikroviļņu krāsns u.c.

Komunikācija (datu apmaiņa) ir atkarīga no WLAN vai Bluetoothâ ierīču programmatūras.

Lietuvių

Šiuo dokumentu Micro Star International CO., LTD, MSI pareiškia, kad šis prietaisas atitinka pagrindinius

1999/5/EB direktyvos reikalavimus ir kitas atitinkamas sąlygas. Atitinkamą Atitikimo pažymėjimą galima rasti

internete adresu:

IEEE 802.11b/g ir Bluetoothâ 2.4 GHz veikimas

Europa: dažniai: 2.400 – 2.4835 GHz

Prancūzija: dažniai: 2.4465– 2.4835 GHz,

Naudojimas lauke ribojamas 10mW e.i.r.p. 2454-2483.5 MHz diapazono juostoje.

Italy:

Jei naudojamas ne savo patalpose, reikalingas bendras leidimas.

Luxembourg:

Visuomeniniam naudojimui reikalingas bendras leidimas.

Naudojama šalyse:

Germany, UK, Netherlands, Belgium, Sweden, Denmark, Finland, France, Italy, Spain, Austria, Ireland,

Portugal, Greece, Luxembourg, Estonia, Letvia, Lithuania, Czech Republic, Slovakia , Slovenia, Hungary,

Poland und Malta.

Naudojimo paskirtis:

Į šio produkto sudėtį įeina WLAN- ir (arba) Bluetoothâ prietaisas.

Prietaisas nustato kompiuterio radijo ryšį. Be to, WLAN- arba Bluetoothâ prietaisą galima prijungti prie bet

kokio kito WLAN- arba Bluetoothâ prietaiso, kuris pagamintas laikantis IEEE 802.11b/g arba Bluetoothâ

reikalavimų.

Veikimo zona:

Skirtingų WLAN- arba Bluetoothâ prietaisų transmisija kinta atsižvelgiant į specifinę aplinką. Sienos,

betoninės grindys (geležis), laminuoti langai, transporto priemonės kėbulas ir pan.

Elektromagnetiniai trukdžiai:

- bet kokios rūšies aukšto dažnio emisijos,

- pastatai, medžiai ir pan.

- šildytuvai, gelžbetonis ir pan.

- atidarytos kompiuterinės sistemos ir pan.

- mikrobangų krosnelės ir pan.

Komunikacija (duomenų apsikeitimas) priklauso nuo WLAN arba Bluetoothâ prietaisų programinės įrangos.

Malti

B’dan, Micro Star International CO., LTD tiddikkjara li dan l-apparat iħares il-ħtiġijiet essenzjali u d-

dispożizzjonijiet oħrajn relevanti tad-Direttiva 1999/5/KE. Id-Dikjarazzjoni rispettiva tal-konformità tista’ tinstab

fuq is-sit ta’ l-internet:

http://www.msi-computer.de/support/dl_man.php

L-operat ta’ l-IEEE 802.11b/g u l-Bluetoothâ fuq 2.4GHz

L-Ewropa: Frekwenzi: 2.400 – 2.4835 GHz

Franza: Frekwenzi: 2.4465– 2.4835 GHz,

L-użu barra huwa limitat għal 10mW e.i.r.p. fi ħdan il-faxxa 2454-2453.5 MHz

Italy:

Tinħtieġ awtorizzazzjoni ġenerali jekk jintuża ‘l barra mill-post tas-sid stess.

Luxembourg:

Tinħtieġ awtorizzazzjoni ġenerali għas-servizz pubbliku.

Pajjiżi Notifikati:

Germany, UK, Netherlands, Belgium, Sweden, Denmark, Finland, France, Italy, Spain, Austria, Ireland,

Portugal, Greece, Luxembourg, Estonia, Letvia, Lithuania, Czech Republic, Slovakia , Slovenia, Hungary,

Poland und Malta.

Użu preskritt:

Dan il-prodott jintegra apparat ta’ WLAN- u/jew Bluetoothâ .

Dan l-apparat jistabbilixxi link bejn żewġ kompjuters. Barra minn hekk, huwa possibbli li jiġi stabbilit link bejn l-

apparat tal-WLAN- jew Bluetoothâ ma’ kull apparat ieħor tal-WLAN- jew Bluetoothâ li jħarsu strettament il-

ħtiġijiet ta’ l-IEEE 803.11b/g jew tal-Bluetoothâ .

Firxa operattiva:

Il-firxa tat-trasmissjoni bejn apparat differenti tal-WLAN- u jew Bluetoothâ ivarja waqt li jiddipendi fuq l-

ambjent speċifiku. Ħitan, l-art tal-konkrit (ħadid), twieqi laminati, il-bodi tal-vetturi, eċċ..

Iktar interferenzi elettromanjetiċi:

- emmissjonijiet ta’ frekwenza għolja ta’ kull tip,

- Bini, siġar, eċċ.

- Ħiters, konkrit bil-ħadid, eċċ.

- sistemi tal-kompjuter miftuħin, eċċ.

- Fran tal-majkrowejv, eċċ.

Il-kommunikazzjoni (skambju ta’ data) hija dipendenti fuq is-software għall-apparat tal-WLAN jew Bluetoothâ .

Polski

Niniejszym dokumentem Micro-Star International Co., LTD zaświadcza, że urządzenie to jest zgodne z

istotnymi wymaganiami Dyrektywy Unijnej 1999/5/EC. Odpowiednią deklarację zgodności można odnaleźć

pod adresem internetowym: http://www.msi-computer.de/support/dl_man.php

Zakres działania IEEE 802.11b/g i Bluetoothâ 2.4 GHz

Europa: Częstotliwości: 2.400 – 2.4835 GHz

Francja: Częstotliwości: 2.4465– 2.4835 GHz,

Użycie na zewnątrz jest ograniczone do 10mW e.i.r.p. w zakresie pasma 2454-2483.5 MHz.

Włochy:

W przypadku zewnętrznego użycia we własnym zakresie, wymagane jest ogólne zezwolenie.

Luxemburg:

Wymagane jest odpowiednie zezwolenie do publicznego użytku.

Dotyczy krajów:

Niemcy, Wielka Brytania, Holandia, Belgia, Szwecja, Dania, Finlandia, Francja, Włochy, Hiszpania, Austria,

Islandia, Portugalia, Grecja, Luxemburg, Estonia, Łotwa, Litwa, Czechy, Słowacja, Słowenia, Węgry, Polska i

Malta.

Przeznaczenie:

Ten produkt łączy w sobie urządzenia WLAN- i/lub Bluetoothâ .

Urządzenie to ustanawia łącze radiowe z komputerem. Dodatkowo jest możliwe połączenie tego urządzenia

WLAN- lub Bluetoothâ z innymi urządzeniami WLAN- lub Bluetoothâ , pod warunkiem spełnienia wymagań

IEEE 802.11b/g lub Bluetoothâ .

Zakres działania:

Zasięg transmisji pomiędzy różnymi urządzeniami WLAN lub Bluetoothâ zależy od warunków w jakich są

one użytkowane. Ściany, betonowe podłogi (żelazo), okna laminowane, karoseria samochodowa itp. mogą

powodować zakłócenia.

Inne zakłócenia elektromagnetyczne mogą być powodowane przez:

- różnego rodzaju wysokie częstotliwości,

- budynki, drzewa itd.

- grzejniki, beton, żelazo,

- otwarte obudowy komputerów,

- kuchenki mikrofalowe itp.

Połączenie (wymiana danych) zależy od oprogramowania urządzeń WLAN lub Bluetoothâ .

Português

Pela presente, Micro Star International CO., LTD declara que este dispositivo cumpre com os requerimentos

essenciais e outras disposições relevantes da Directiva 1999/5/EC. A Declaração de conformidade

correspondente pode-se encontrar online:

http://www.msi-computer.de/support/dl_man.php

Operação IEEE 802.11b/g e Bluetoothâ 2.4 GHz

Europa: Frequências: 2.400 – 2.4835 GHz

França: Frequências: 2.4465– 2.4835 GHz,

O uso ao ar livre está limitado a 10mW e.i.r.p. dentro da banda 2454-2483.5 MHz

Itália:

Se utilizar afora das próprias instalações, requere-se autorização geral.

Luxemburgo:

Requere-se autorização geral para serviço público.

Países Notificados:

Alemánia, Reino Unido, Holanda, Bélgica, Suécia, Dinamarca, Finlándia, França, Itália, Espanha, Austria,

Irlanda, Portugal, Grécia, Luxemburgo, Estônia, Letvia, Lituânia, República Tcheca, Eslováquia , Eslovénia,

Hungria, Polônia e Malta.

Utilização:

Este produto integra o dispositivo Bluetoothâ e/ou WLAN.

O dispositivo configura um vínculo de radio link com o computador. Além disso pode conectar o dispositivo

Bluetoothâ e/ou WLAN com qualquer outro dispositivo Bluetoothâ e/ou WLAN que cumpra com as normas

IEEE 802.11b/g ou requerimentos Bluetoothâ .

Radio de Operação:

O alcanço de transmissão entre diferentes dispositivos WLAN ou Bluetoothâ varia dependendo do ambiente

específico. Paredes, pisos de concreto (ferro), janelas laminadas, corpos condutores, etc..

Mais interferências eletromagnéticas:

- Emissões de alta frecuência de qualquer classe,

- Edifícios, árvores, etc.

- Aquecedores, etc.

- Sistemas de computador abertos,

- Forno Microondas,

A comunicação (intercâmbio de dados) depende do software dos dispositivos WLAN ou Bluetoothâ .

Slovensky

Micro Star International CO., LTD prehlasuje, že je zariadenie v súlade so základnými požiadavkami a inými

príbuznými podmienkami Nariadenia 1999/5/EC. Príslušnú deklaráciu o zhode je možné nájsť na internetovej

stránke:

http://www.msi-computer.de/support/dl_man.php

Činnosť IEEE 802.11b/g a Bluetoothâ 2.4 GHz

Európa: Frekvencie: 2.400 – 2.4835 GHz

Francúzsko: Frekvencie: 2.4465– 2.4835 GHz,

Vonkajšie použitie je limitované na 10mW v pásme 2454-2483.5 MHz

Italy:

Ak sa používa mimo vlastných priestorov, vyžaduje sa všeobecná plná moc.

Luxembourg:

Pre verejné služby sa vyžaduje všeobecná plná moc.

Oboznámené krajiny:

Germany, UK, Netherlands, Belgium, Sweden, Denmark, Finland, France, Italy, Spain, Austria, Ireland,

Portugal, Greece, Luxembourg, Estonia, Letvia, Lithuania, Czech Republic, Slovakia , Slovenia, Hungary,

Poland und Malta.

Predpísané použitie:

Tento produkt v sebe zahŕňa WLAN- a/alebo Bluetoothâ zariadenie.

Zariadenie nastavuje rádiové spojenie s počítačom. Naviac je možné pripojiť zariadenie WLAN alebo

Bluetoothâ k inému WLAN- alebo Bluetoothâ zariadeniu, ktoré sa viaže na požiadavky IEEE 802.11b/g

alebo Bluetoothâ .

Pracovný rozsah:

Rozsah vysielania medzi rôznymi WLAN alebo Bluetoothâ zariadeniami závisí od špecifickosti prostredia.

Múry, betónová podlaha (železo), laminátové okná, karosérie áut, atď.

Ďalšie elektromagnetické interferencie:

- vysokofrekvenčné emisie rôzneho druhu,

- Budovy, stromy, atď.

- Ohrievače, železobetón, atď.

- otvorené počítačové systémy, atď.

- Mikrovlnná rúra, atď,

Komunikácia (výmena dát) je závislá od softvéru WLAN alebo Bluetoothâ zariadení.

Slovenèina

S tem, Micro Star International CO., LTD s polno odgovornostjo izjavljamo, da je ta naprava skladna z

pomembnimi zahtevami in vsemi bistvenimi predpisi direktive 1999/5/EC. Kopijo izjave o ustreznosti najdete

na naslovu:

http://www.msi-computer.de/support/dl_man.php

Območje delovanja IEEE 802.11b/g in Bluetoothâ 2.4 GHz

Evropa: frekvenčno območje: 2.400 – 2.4835 GHz

Francija: frekvenčno območje: 2.4465– 2.4835 GHz

Uporaba na prostem je omejena na 10 mW e.i.r.p. v frekvenčnem območju 2454-2483.5 MHz

Italy:

Če se uporablja izven določene meje, je potrebno ustrezno dovoljenje.

Luxembourg:

Za uporabo v javnosti je potrebno posebno dovoljenje.

Prijavljene države:

Germany, UK, Netherlands, Belgium, Sweden, Denmark, Finland, France, Italy, Spain, Austria, Ireland,

Portugal, Greece, Luxembourg, Estonia, Latvia, Lithuania, Czech Republic, Slovakia , Slovenia, Hungary,

Poland und Malta.

Predpisana uporaba:

Ta izdelek je sestavljen iz WLAN- in/ali Bluetoothâ naprave.

Naprava je brezžično, radijsko povezana z računalnikom. Poleg tega je možno povezati WLAN- ali

Bluetoothâ napravo z katerokoli WLAN- ali Bluetoothâ napravo, ki podpira IEEE 802.11b/g ali Bluetoothâ

zahteve.

Delovno območje:

Transmisijsko območje med različnimi WLAN- ali Bluetoothâ napravami je odvisno od delovnega okolja. Npr.

stene, betonska nadstropja (železo), laminirana okna, šasija vozila, ipd.

Vplivi silnega elektromagnetnega polja:

- kakršno koli visoko frekvenčno oddajanje

- zgradbe, drevesa, ipd.

- grelci, železobeton, ipd.

- odprti računalniški sistemi, ipd.

- mikrovalovne peči, ipd.

Komunikacija (prenos podatkov) je odvisna od programske opreme WLAN ali Bluetoothâ naprave.

Español

Por la presente, Micro Star Internacional CO., LTD, declara que este dispositivo cumple las exigencias

esenciales y otras previsiones importantes de la Directiva 1999/5/EC. La correspondiente declaración de

conformidad puede encontrarse online en

http://www.msi-computer.de/support/dl_man.php

IEEE 802.11b/g y Bluetoothâ 2.4 GHz operación

Europe: Frecuencias: 2.400 – 2.4835 GHz

France: Frecuencias: 2.4465– 2.4835 GHz,

El uso exterior está limitado a 10mW e.i.r.p. dentro de la banda de 2454-2483.5 MHz

Italia:

Se requiere autorización para su empleo fuera de sus propios establecimientos

Luxemburgo:

Se requiere autorización para su utilización pública

Países notificados:

Alemania, Reino Unido, Países Bajos, Bélgica, Suecia, Dinamarca, Finlandia, Francia, Italia, España, Austria,

Irlanda, Portugal, Grecia, Luxemburgo, Estonia, Letonia, Lituania, República Checa, Eslovaquia, Eslovenia,

Hungría, Polonia y Malta.

Modo de funcionamiento

Este producto integra un dispositivo WLAN y/o un dispositivo Bluetoothâ

El dispositivo establece un radio enlace con el ordenador. Además, es posible enlazar el dispositivo WLAN o

Bluetoothâ a cualquier otro dispositivo WLAN o Bluetoothâ que se atenga a las exigencias del IEEE 802.11

b/g o Bluetoothâ .

Rango de Funcionamiento:

La tasa de transmisión entre los dispositivos WLAN y Bluetoothâ varía dependiendo del entorno específico.

Paredes, determinados suelos (hierro), ventanas laminadas, cuerpos transmisores, etc.

Más interferencias electromagnéticas:

Emisiones de alta frecuencia de cualquier tipo

Edificios, árboles, etc.

Calentadores, hormigón armado, etc.

Sistemas informáticos abiertos, etc.

Microondas, etc

La comunicación (intercambio de datos) depende del software de los dispositivos WLAN o Bluetoothâ

SVENSKA

Härmed intygar Micro Star International CO., LTD att denna anordning överensstämmer med baskraven och

andra relevanta föreskrifter i direktivet 1999/5/EC. Själva Deklarationen om överensstämmelse i fråga kan

hittas on-line på:

http://www.msi-computer.de/support/dl_man.php

IEEE 802.11b/g och Bluetoothâ 2.4 GHz- operation

Europa: Frekvenser: 2,400 – 2,4835 GHz

Frankrike: Frekvenser: 2,4465– 2,4835 GHz,

Användning utomhus är begränsat till 10mW e.i.r.p. inom bandet 2454-2483.5 MHz

Italy:

Om den används utanför den egna bostaden, krävs ett allmänt godkännande.

Luxembourg:

Allmänt godkännande krävs för offentlig service.

Aviserade länder:

Germany, UK, Netherlands, Belgium, Sweden, Denmark, Finland, France, Italy, Spain, Austria, Ireland,

Portugal, Greece, Luxembourg, Estonia, Letvia, Lithuania, Czech Republic, Slovakia , Slovenia, Hungary,

Poland und Malta.

Fastställt bruk:

Denna produkt integrerar en WLAN- och/eller Bluetoothâ - anordning.

Anordningen sätter upp en radiolänk mellan två datorer. Det är dessutom möjligt att länka WLAN- eller

Bluetoothâ - anordningen till vilken annan WLAN- eller Bluetoothâ - anordning som helst som följer kraven

som anges i IEEE 802.11b/g eller Bluetoothâ .

Funktionsräckvidd:

Programöverföringen mellan olika WLAN- eller Bluetoothâ - anordningar varierar beroende på den specifika

miljön. Väggar, betonggolv (järn), laminerade fönster, fordonets kaross o.s.v.

Fler elektromagnetiska störningar:

– någon slags emission på hög frekvens,

– Byggnader, träd o.s.v.

– Värmare, betongjärn o.s.v.

– öppna datorsystem o.s.v.

– Mikrovågsugn o.s.v.

Kommunikation (utbyte av data) är beroende av WLAN eller Bluetoothâ - anordningarnas mjukvara.

JVC AV 21C15 User Manual
JVC AV 21MT36 User Manual
JVC CRT Television AV 27F475 User Manual
JVC LCT2142 001A H User Manual
Miele INDUCTION WOK CS 1223 User Manual
Motorola L703c Cordless Phone L703C User Manual
Philips 17GR2746 User Manual
Philips DVP3336 User Manual
Philips FWD831 User Manual
Philips HDR3500 User Manual