Lucent Technologies CIB40 User Manual

Lucent Technologies  
Bell Labs Innovations  
CIB 3140  
(533B) Memory Module (61227A)  
(106433691)  
CIB 3140  
Comcode 106433691  
Issue 2  
January 1997  
Memory Module  
When installed in the MERLIN® Plus system control unit, this memory  
module (Figure 1) upgrades your system to the MERLIN Plus Communi-  
cations System Release 2.  
MEMORY  
MODULE  
Figure 1  
MERLIN Plus Communications System Release 2 Memory Module  
The new system features available with this memory module are listed  
below. For further informaiton about each feature, refer to Section 5,  
"Reference," of your new MERLIN Plus Communicaiton System  
Release 2 System Manual.  
Automatic System Access Features  
> Call Forwarding (CF)  
> Direct Extension Dialing (DXD)  
> Remote Line Access (RLA)  
> System Answer (SA)  
Busy Buster  
Disallowed Lists  
Exclusive Hold  
Hold Disconnect Interval  
Program Mode Lock  
Voice Terminal Template  
NOTE: Some programming  
operations also vary for the MERLIN Plus  
Communications System Release 2. Refer to your new System Manual  
for further information. This memory module comes with two 2-foot  
(D4BU) modular cords. These cords are used to connect the Busy Bus-  
ter (BB) and Automatic System Acces (ASA) features as explained in  
Secton 5 of your new System Manual.  
1
NOTE: This memory module also houses a battery that preserves all  
programming for at least four days in case of a power failure.  
In addition, a 450F adapter is included to provide a connection between  
the control unit and the Data Collector, and to allow the Data Collector  
and the Busy Buster feature to share the same jack on the voice terminal  
module. Refer to the Addendum to CIB 3051 for installation instructions.  
INSERTING AND REMOVING THE MEMORY MODULE  
Follow the procedures listed below for inserting and removing this  
memory module.  
NOTE: You will have to readminister and reprogram your voice terminals  
after you have installed this memory module.  
Make sure the power cord is unplugged and the  
WARNING:  
power switch on the control unit is set to Off before you insert or  
remove any modules. You risk damage to the system and the  
modules if the power is on during the installation procedure.  
Remove the front cover from the control unit by pressing down on the  
two top corner tabs and putting the top away from the control unit  
1
2
Remove the top cover by first unscrewing the screw located at the  
center bottom of the cover. (This screw is designed to stay in the  
hole of the cover after it has been removed from the control unit.)  
Then press down on the tab located at the center of the top and back  
3
To remove the old memory module, depress the tab on top of the  
module labeled Press To Remove, grasp the plastic handle on the  
front of the memory module and pull the memory module out of the  
control unit.  
2
Memory module  
Figure 3  
Inserting and Removing the Memory Module  
8 Plug the power cord back into the outlet and set the power switch on  
the control unit to On.  
9 Replace the front cover on the control unit.  
Remember, you will have to readminister and reprogram your sets as  
described in Section 3, "Administering the System," of your new System  
Manual.  
4
 
Customer Administerable Timer  
The Customer Administerable Timer is used in conjunction with the Call  
Forwarding and Remote Line Access features. The timer disconnects  
calls made via Call Forwarding and/or Remote Line Access after these  
calls reach a system-wide call duration limit. The Customer  
Administerable Timer can be set to a value of from 1 to 999 minutes.  
To administer the Customer Administerable Timer:  
1.  
Enter administration mode by sliding the T/P switch to P  
and touching Administer.  
2.  
3.  
Dial *68.  
Dial the desired three-digit timer value. Three digits must  
be dialed. For example, a timer value of 1 minute would  
be dated as 001, a value of 10 minutes would be dialed  
as 010, and a value of 120 minutes (2 hours) would be  
dialed as 120. To reset the timer to its default value of  
no time limit, dial 000.  
4. Touch Administer. The console beeps twice.  
5.  
Leave administration by sliding the T/P switch to the center  
position.  
RECYCLED PAPER  
Lucent Technologies  
Bell Labs Innovations  
1996, Lucent Technologies  
Copyright ©  
All Rights Reserved  
Printed in U.S.A.  

HP Hewlett Packard ProLiant ML110 G5 User Manual
KitchenAid KGCC506RBB00 User Manual
Lucent Technologies Computer Hardware R5SI User Manual
Magnavox 27MDTR10S User Manual
MSi MS 6534 User Manual
NEC NLT 26HD1 User Manual
Oki 70042401 User Manual
Philips 28PT4473 User Manual
Philips 150b5 User Manual
Philips ONIS Memo 6411 User Manual