User’s Guide
W2363V
Make sure to read the Important Precautions before using the
product. Keep the User's Guide(CD) in an accessible place for future
reference.
See the label attached on the product and give the information to
your dealer when you ask for service.
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place
the display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,
mar, or damage the Active Matrix LCD permanently.
Do not press the LCD screen with your finger for a long time as this may cause
some afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance.
If possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.
Leaving a fixed image on the screen for a long time may cause damage to the
screen and cause image burn-in. Make sure to use a screen saver on the product.
Burn-in and related problems are not covered by the warranty on this product.
Do not shock or scratch the front and sides of the screen with metallic objects.
Otherwise, it may cause damage to the screen.
Make sure the panel faces forward and hold it with both hands to move. If you
drop the product, the damaged product can cause electric shock or fire. Contact
an authorized the service center for repair.
Avoid high temperatures and humidity.
2
Important Precautions
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
When cleaning the product, unplug the power cord and scrub gently with a soft
cloth to prevent scratching. Do not clean with a wet cloth or spray water or
other liquids directly onto the product. An electric shock may occur. (Do not use
chemicals such as benzene, paint thinners or alcohol)
Spray water onto a soft cloth 2 to 4 times, and use it to clean the front frame;
wipe in one direction only. Too much moisture may cause staining.
On Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
On Disposal (Only, Hg lamp used LCD Monitor)
The fluorescent lamp used in this product contains a small amount of mercury.
Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of
your local authority.
3
Accessories
!!! Thank for selecting LGE products !!!
Please make sure the following items are included with your
monitor. If any items are missing, contact your dealer.
Power Cord
(Depending on the country)
User's Guide/Cards
15-pin D-Sub Signal Cable
(To set it up, this signal cable may
be attached to this product before
shipping out.)
DVI-D Signal Cable
(This feature is not available
in all countries.)
IMPORTANT
This accessories may look different from those shown here.
User must use shielded signal interface cables (D-sub 15 pin cable, DVI cable) with ferrite
cores to maintain standard compliance for the product.
4
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor,
the computer system, and other attached devices is turned off.
Connecting and Disassembling the stand
1. Place the monitor face down on the soft cloth.
2. Assemble the Stand Base into the Stand Body in the correct direction.
Make sure you push the Stand Base until the end.
Stand Body
Stand Base
The Stand Base may
fall and get damaged
or cause injury.
Good Connection
Bad Connection
5
Connecting the Display
3. Turn the screw to the right to fix the Stand Body to the Stand Base.
Screw
Turn the screw
by using the
screw handle.
4. Then fold the screw handle flat.
5. Once assembled take the monitor up
carefully and face the front side.
6. To disconnect the Stand Base from the Stand Body, unfold the screw handle and
turn it to the left.
IMPORTANT
This picture depicts the general model of connection. Your monitor may differ from the items
shown in the picture.
Do not carry the product upside down holding only the stand base. The product may fall and
get damaged or cause injury.
6
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor,
the computer system, and other attached devices is turned off.
Positioning your display
After installation, adjust the angle as shown below.
1. Adjust the position of the panel in various ways for maximum comfort.
Tilt Range: -5˚~15˚
15
-5
Do not touch or press the screen when
adjusting the angle of the monitor.
When adjusting the angle of the screen, do
not put your finger(s) in between the head of
the monitor and the stand body. You can
hurt your finger(s).
ERGONOMIC
It is recommended that in order to maintain an ergonomic and comfortable viewing position,
the forward tilt angle of the monitor should not exceed 5 degrees.
7
Connecting the Display
Connecting with the PC/AV equipment
1. Before setting up the monitor, ensure that the power to the monitor, the computer
2. sCyosntenmec,tasnigdnoatlhienrpautttacachbeled devicaensdipsotuwrenrecdoordff.
in order, then tighten the screw of
1
2
the signal cable.
A
B
C
D
Connect DVI-D (Digital signal) Cable
Connect D-sub (Analog signal) Cable
Connect VIDEO and AUDIO Cable
Connect HDMI Cable (HDMI1, HDMI2)
NOTE
This is a simplified representation of the rear view.
This rear view represents a general model; your display may differ from the view as shown.
AV equipment
(Set-Top Box, DVD,
Video,Video Game Console)
* HDMI is optimized on the AV equipment.
* Not supported PC.
Headphone/Earphone output
Varies according to model
Wall-outlet type
PC input
DVI-D (This feature is not available in all countries.)
DVD player or others which have component port
When using a D-Sub signal input cable connector for Macintosh
Mac adapter: For Apple Macintosh use, a separate plug adapter
is needed to change the 15 pin high density (3 row) D-sub VGA
connector on the supplied cable to a 15 pin 2 row connector.
8
Connecting the Display
3. Press the Power Button (
) on the front panel to turn the power on. When monitor
power is turned on, the 'Self Image Setting Function' is executed automatically.
(Only Analog Mode)
NOTE
‘ Self Image Setting Function’? This function provides the user with optimal display settings.
When the user connects the monitor for the first time, this function automatically adjusts the
display to optimal settings for individual input signals.
‘AUTO/SET’ Function? When you encounter problems such as blurry screen, blurred letters,
screen flicker or tilted screen while using the device or after changing screen resolution, press
the AUTO/SET function button to improve resolution.
9
Control Panel Functions
Front Panel Controls
Button
Use this button to enter THRU MODE, SRS
TRUSURROUND HD, ARC or AUTO BRIGHT menus.
For more information, refer to page 14 ~ 15.
When two or more input signals are connected, first
monitor automatically detects one signal as main input,
then you can select the input signal (DSUB/DVI/HDMI1/
HDMI2/COMPONENT) you want.
SOURCE Button
INPUT
Use this button to enter or exit the On Screen Display.
MENU Button
OSD LOCKED/UNLOCKED
This function allows you to lock the current control
settings, so that they cannot be inadvertently changed.
Press and hold the MENU button for several seconds.
The message "OSD LOCKED" should appear.
You can unlock the OSD controls at any time by pushing
the MENU button for several seconds. The message
"OSD UNLOCKED" should appear.
10
Control Panel Functions
Use these buttons to select or adjust functions in the On
Screen Display.
Buttons
Use this button you can directly use PIP function.
You can use PIP menu to select PIP input.
For more information, refer to page 21.
When two input signals are connected, one is main
input, the other is PIP input. You can use this button to
exchange the main input and PIP input.
AUTO/SET
Button
Use this button to enter a selection in the On Screen
Display.
AUTO IMAGE ADJUSTMENT
When adjusting your display settings, always press the
AUTO/SET button before entering the On Screen
Display(OSD). (Only DSUB and component mode)
This will automatically adjust your display image to the
ideal settings for the current screen resolution size
(display mode).
The best display mode is: 1920 x 1080
TRU-LIGHT
GAME
Use this button to select LED light mode,
TRU-LIGHT
Button
GAME, MOVIE, MUSIC or turn off the
MOVIE
LED light.
MUSIC
OFF
Use this button to turn the display on or off.
Power Button
The power indicator stays blue if the display is running
properly (On Mode). If the display is in Sleep Mode
(Energy Saving), the power indicator is blinking blue.
Power Indicator
11
On Screen Display (OSD) Control Adjustment
Screen Adjustment
Making adjustments to the image size, position and operating
parameters of the display is quick and easy with the On Screen
Display Control system.
A short example is given below to familiarize you with the use of the
controls. The following section is an outline of the available
adjustments and selections you can make using the OSD.
To make adjustments in the On Screen Display, follow these steps:
Move where
Select a
Adjust the
status
Exit from the
menu screen.
Pops up the
menu screen
you want to
adjust
menu icon
Press the MENU Button, then the main menu of the OSD appears.
1
2
To access a control, use the
or
Buttons. When the icon you want
becomes highlighted, press the AUTO/SET Button.
Use the
/
Buttons to adjust the image to the desired level.
3
4
Use the AUTO/SET Button to select other sub-menu items.
Press the MENU Button once to return to the main menu to select another
function. Press the MENU Button twice to exit from the OSD.
12
On Screen Display(OSD) Selection and Adjustment
The following table indicates all the On Screen Display control, adjustment, and setting
menus.
Main menu
Sub-menu
Reference
Use Frame-Buffer to prevent
picture delay
THRU MODE
Use 3D surround for live sound
effect
SRS TRUSURROUND HD
ARC
Use aspect ratio control
To control screen brightness
automatically
AUTO BRIGHT
BRIGHTNESS
To adjust the brightness, contrast
and gamma of the screen
CONTRAST
GAMMA
PICTURE
To set offset level
BLACK LEVEL
To adjust screen status for
operating environment
WHITE BALANCE
sRGB
6500K
9300K
PRESET
RED
To adjust screen color mode
GREEN
COLOR
BLUE
HUE
SATURATION
COLOR RESET
HORIZONTAL
VERTICAL
CLOCK
To adjust the position of the
screen
TRACKING
To improve the clarity and stability
of the screen
PHASE
SHARPNESS
LANGUAGE
HORIZONTAL
VERTICAL
OSD
POSITION
R T C
To customize the screen status
for a user's operating environment
VOLUME
OVERSCAN
SETUP
LIGHTING LEVEL
POWER INDICATOR
FACTORY RESET
PIP ON/OFF
PIP INPUT
PIP
To adjust PIP function
PIP POSITION
PIP SOUND
●: Adjustable
A : DSUB Input
D : DVI Input
H : HDMI Input
C : COMPONENT Input
NOTE
The order of icons may differ depending on the model (13~21).
13
On Screen Display(OSD) Selection and Adjustment
The OSD screen will appear when you press the
the monitor.
button on the front of
Menu Name
G-MODE
MENU : Save & Exit
: Move
Icons
,
Sub-menu Name
THRU MODE
ON
Main menu
G-MODE
Sub menu
Description
ON
THRU MODE
Not use the Frame-Buffer memory to
prevent the picture delay. It can use in
GAME MODE to prevent picture delay.
THRU MODE
ON
OFF
Using the Frame-Buffer memory to control
PIP, ARC function.
If user selects “THRU MODE ON” with
“PIP ON”, “THRU MODE” will turn "OFF"
automatically.
SRS TRUSURROUND HD
ON
G-MODE
Turn on SRS function, offer 3D surround
SRS TRUSURROUND HD
for live sound effect.
OFF
Turn off SRS function.
is a trademark of SRS Labs, Inc.
TruSurround HD technology is incorporated under license from SRS Labs, Inc.
14
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
1:1
ARC
G-MODE
The picture will be displayed depends on
Input resolution.No Scaling. If 640x480
resolution input, the picture will just
display 640x480 size even though the
1920x1080 size panel.
ARC
FULL
ORIGINAL
The picture will be displayed with input
resolution ratio scaling. If 640x480
resolution input, the picture will keep at
4:3 ratio scaling.
FULL
The picture will be displayed with Full
size.
AUTO BRIGHT To control screen brightness automatically.
When ON is selected, this function adjusts
the screen brightness automatically,
G-MODE
depending on the display data levels, to
provide optimal viewing conditions. When
OFF is selected, this function is turned off.
AUTO BRIGHT
ON
15
On Screen Display(OSD) Selection and Adjustment
You were introduced to the procedure of selecting and adjusting an item
using the OSD system. Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
Press the MENU Button, then the main menu of the OSD appears.
Main Menu
MENU
SET
: Exit
: Adjust (Decrease/Increase)
: Enter
: Select another sub-menu
: Restart to select sub-menu
Button
Tip
Menu Name
Icons
Sub-menus
NOTE
OSD (On Screen Display) menu languages on the monitor may differ from the manual.
16
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
PICTURE
DVI, DSUB input
To adjust the brightness of the screen.
To adjust the contrast of the screen.
BRIGHTNESS
CONTRAST
GAMMA
Set your own gamma value: -50/0/50
On the monitor, high gamma values
display whitish images and low gamma
values display blackish images.
HDMI, COMPONENT input
BLACK LEVEL You can set the offset level. If you select
'HIGH', the screen will be bright and if
you select ‘LOW’, the screen will be dark.
* Offset? As the criteria for video signal, it is the
darkest screen the monitor can show.
WHITE
If the output of the video card is
different from the required
BALANCE
specifications, the color level may
deteriorate due to video signal
distortion. Using this function, the
signal level is adjusted to fit into the
standard output level of the video card
in order to provide the optimal image.
Activate this function when white and
black colors are present in the screen.
(Only for DSUB input)
MENU : Exit
: Decrease
: Increase
SET : Select another sub-menu
17
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
COLOR
DVI, DSUB input
PRESET
• sRGB: Set the screen color to fit
the sRGB standard color
specification.
• 6500K: Slightly reddish white.
• 9300K: Slightly bluish white.
Set your own red color levels.
Set your own green color levels.
Set your own blue color levels.
Set your own HUE levels.
RED
GREEN
BLUE
HUE
Set your own saturation levels.
SATURATION
COLOR RESET
Prestore “PICTURE” and “COLOR”
default settings.
HDMI, COMPONENT input
MENU : Exit
: Decrease
: Increase
SET : Select another sub-menu
18
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
TRACKING
DSUB input
HORIZONTAL
VERTICAL
To move image left and right.
To move image up and down.
CLOCK
To minimize any vertical bars or stripes
visible on the screen background.
The horizontal screen size will also
change.
PHASE
To adjust the focus of the display.
This item allows you to remove any
horizontal noise and clear or sharpen
the image of characters.
DVI, HDMI, COMPONENT input
SHARPNESS
To adjust the clearness of the screen.
MENU : Exit
: Decrease
: Increase
SET : Select another
sub-menu
19
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
SETUP
To choose the language in which the control
names are displayed.
LANGUAGE
To adjust position of the OSD window on the
screen.
OSD
POSITION
If you set ON, you enable the Response Time
Control function.
R T C
If you set OFF, you disable the Response
Time Control function.
VOLUME
To adjust the volume of headphone/Earphone.
VOLUME
LIGHTING LEVEL
3
To select the range of output image for DTV
timing in HDMI input.
OVERSCAN
(only for HDMI input)
1920 x 1080
Recommend overscan function to turn on when
connect AV equipment.
MENU : Exit
: Adjust
: Adjust
The White LED will move from center of the
PCB depends on Sound input signal level.
If sound signal level is lower than Threshold
level, the LED cannot operate.
LIGHTING
LEVEL
SET : Select another
sub-menu
About LIGHTING LEVEL, you can change
from 0 to 10.
If No sound input, the LED has no action.
Use this function to set the power indicator on the
front side of the monitor to ON or OFF.
If you set OFF, it will go off.
POWER
INDICATOR
If you set ON at any time, the power indicator will
automatically be turned on.
Restore all factory default settings except
FACTORY
RESET
"LANGUAGE".
Press the
,
buttons to reset immediately.
If this does not improve the screen image, restore the factory default settings.
If necessary, perform the white balance function again. This function will be enabled only when
the input signal is an analog signal.
20
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
PIP
PIP ON/OFF
To select PIP on or off.
* It supports only for HDMI input in RGB
PIP ON/OFF
PIP INPUT
ON
(
D-sub analog signal) mode.
* The combinations of main screen and
sub-screen (PIP) available are as shown
below:
DVI
PIP POSI TION
PIP SOUND
OFF
Main screen
Compon-
RGB
DVI
HDMI #1 HDMI #2
ent
Sub-screen (PIP)
RGB
-
X
-
O
O
-
O
O
O
-
O
O
O
X
-
MENU : Exit
X
O
O
O
Component
DVI
HDMI #1
HDMI #2
: Adjust
: Adjust
O
O
O
O
O
AUTO/SET : Select another
X
sub-menu
Select PIP input.
PIP INPUT
Select the PIP display location. Every
time you touch the button, it will move
PIP POSITION
4
3
1
2
from to
,
,
. Every time you
1
press the button, it will move from
2
4
3
to
,
,
. You can use this menu to
select the PIP display location you want.
1
: Top left
2
: Bottom left
3
: Bottom right
4
: Top right
*It operates only when PIP is on.
PIP SOUND
PIP SOUND ON: The PIP Sound
enable in PIP ON condition. If PIP
OFF, the PIP Sound cannot be
operated even if the user changes the
PIP Sound ON/OFF in the OSD menu.
PIP SOUND OFF: The PIP Sound
disable.
* Limitation.
Cannot support the DSUB (Main/Sub) & DVI (Sub/Main) PIP Sound Function.
21
Troubleshooting
Check the following before calling for service.
No image appears
● Is the power cord of the
• Check and see if the power cord is connected
properly to the power outlet.
display connected?
● Is the power indicator
• Press the Power button.
light on?
• If the display is in power saving mode, try
moving the mouse or pressing any key on the
keyboard to bring up the screen.
● Is the power indicator
blinking?
• Try to turn on the PC.
• This message appears when the signal from the
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
● Do you see an "OUT OF
RANGE" message on
the screen?
• This message appears when the signal cable
between your PC and your display is not
connected. Check the signal cable and try
again.
● Do you see a "CHECK
SIGNAL CABLE"
message on the
screen?
Do you see a "OSD LOCKED" message on the screen?
●
Do you see “OSD
LOCKED” when you
push MENU button?
• You can secure the current control settings,
so that they cannot be inadvertently changed.
You can unlock the OSD controls at any time
by pushing the MENU button for several
seconds: the message “OSD UNLOCKED”
will appear.
22
Troubleshooting
Display image is incorrect
● Display Position is
• Press the AUTO/SET button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, adjust the image
position using the H position and V position
icon in the on screen display.
incorrect.
● On the screen
background, vertical
bars or stripes are
visible.
• Press the AUTO/SET button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, decrease the
vertical bars or stripes using the CLOCK icon in
the on screen display.
● Any horizontal noise
appearing in any
image or characters
are not clearly
• Press the AUTO/SET button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, decrease the
horizontal bars using the PHASE icon in the on
screen display.
portrayed.
• Check Control Panel --> Display --> Settings
and adjust the display to the recommended
resolution or adjust the display image to the ideal
setting. Set the color setting higher than 24 bits
(true color).
IMPORTANT
Check Control Panel --> Display --> Settings and see if the frequency or the
resolution were changed. If yes, readjust the video card to the recommend
resolution.
If the recommended resolution (optimal resolution) is not selected, letters may
be blurred and the screen may be dimmed, truncated or biased. Make sure to
select the recommend resolution.
The setting method can differ by computer and O/S (Operation System),
and resolution mentioned above may not be supported by the video card
performance. In this case, please ask to the computer or the video card
manufacturer.
23
Troubleshooting
Display image is incorrect
● The screen color is
•
•
•
Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
Make sure the video card is properly inserted in
the slot.
mono or abnormal.
Set the color setting higher than 24 bits (true color)
at Control Panel - Settings.
● The screen blinks.
•
Check if the screen is set to interlace mode and if
yes, change it to the recommend resolution.
Do you see an "Unrecognized monitor, Plug&Play (VESA DDC)
monitor found" message?
●
Have you installed the
display driver?
•
Be sure to install the display driver from the display
driver CD (or diskette) that comes with your
display. Or, you can also download the driver from
•
Make sure to check if the video card supports
Plug&Play function.
The Audio function is not working
●
Picture OK & No sound.
• Check whether volume is "0".
• Check sound muted.
• HDMI cable installed properly.
• Head phone cable installed properly.
• Check sound format. Not supply to compressed
sound format.
24
Specifications
23.0 inches (58.4 cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
Display
Visible diagonal size: 58.4 cm
x
0.265 0.265 mm (Pixel Pitch)
Horizontal Freq.
Vertical Freq.
Input Form
Analog, Digital: 30 - 83 KHz (Automatic)
Sync Input
Video Input
HDMI: 30 - 83 KHz (Automatic)
Analog, Digital: 56 - 75 Hz (Automatic)
HDMI: 56 - 61 Hz (Automatic)
Separate Sync, Positive/Negative
Digital (HDCP)
Signal Input
Input Form
15 pin D-Sub Connector
DVI-D Connector (Digital)
19 pin HDMI Connector
Analog (0.7 Vp-p/ 75 ohm), Digital, HDMI
Max
VESA 1920 x 1080 @ 60 Hz
1920 x 1080 @ 60 Hz
Resolution
Plug&Play
Recommend
DDC 2B (Analog, Digital, HDMI)
On Mode
Sleep Mode
Off Mode
:
≤
≤
42 W (Typ.)
1.4 W (DSUB/DVI)
1 W
Power
Consumption
Dimensions
& Weight
With Stand
Without Stand
Width
55.55 cm / 21.87 inches
41.92 cm / 16.50 inches
55.55 cm / 21.87 inches
40.95 cm / 16.12 inches
Height
Depth
20.59 cm / 8.10 inches
7.33 cm / 2.88 inches
Net
5.1 kg (11.25 lbs)
Tilt
-5˚~15˚
Tilt Range
AC 100-240V~ 50/60Hz 1.0A
Power Input
Operating Conditions
Environmental
Conditions
Temperature
Humidity
10˚C to 35 ˚C
10 % to 80 % non-Condensing
Storage Conditions
Temperature
Humidity
-20˚C to 60 ˚C
5 % to 90 % non-Condensing
Attached ( ), Detached ( O )
Wall-outlet type
Stand Base
Power cord
NOTE
Information in this document is subject to change without notice.
25
Specifications
Preset Modes (Resolution)
DSUB/DVI Timing
Display Modes (Resolution)
Horizontal Freq. (kHz)
Vertical Freq. (Hz)
1
2
640 x 350
720 x 400
31.469
31.468
31.469
37.500
37.879
46.875
48.363
60.123
67.500
63.981
79.976
64.674
65.290
67.500
70
70
60
75
60
75
60
75
75
60
75
60
60
60
3
640 x 480
4
640 x 480
5
800 x 600
6
800 x 600
7
1024 x 768
1024 x 768
1152 x 864
1280 x 1024
1280 x 1024
1680 x 1050
1680 x 1050
1920 x 1080
8
9
10
11
12
13
*14
*Recommend Mode
HDMI Timing
Display Modes (Resolution)
Horizontal Freq. (kHz)
Vertical Freq. (Hz)
1
2
3
4
5
6
7
8
480P
576P
720P
720P
1080i
1080i
1080P
1080P
31.50
31.25
37.50
45.00
28.12
33.75
56.25
67.50
60
50
50
60
50
60
50
60
26
Specifications
Preset Modes (Resolution)
Component Video Timing
Horizontal Freq. (kHz)
Display Modes (Resolution)
Vertical Freq. (Hz)
1
2
3
4
5
6
7
8
15.75
15.62
31.50
31.25
37.50
45.00
28.12
33.75
480i
576i
60
50
60
50
50
60
50
60
480P
576P
720P
720P
1080i
1080i
Indicator
LED Color
MODE
On Mode
Sleep Mode
Off Mode
Blue
Blue Blinking
Off
27
Installing the Wall mount plate
This monitor satisfies the specifications of the Wall mount plate
or the interchange device.
1. Place the monitor face down on the soft cloth.
2. To disconnect the Stand Base from the Stand Body, unfold the screw handle and
turn it to the left.
3. Pull out the Stand Base to remove.
28
Installing the Wall mount plate
4. Install the Wall mount plate.
Wall mount plate(Separate purchase)
This is stand-type or wall mount type and is
connectable with Wall mount plate.
Please refer to the installation guide for more details,
which is provided when Wall mount plate is
purchased.
Kensington Security Slot
Connected to a locking cable that
can be purchased separately at
most computer stores.
29
Digitally yours
|