Lenovo THINKPAD E40 User Manual

DANGER  
To avoid shock hazard:  
Do not remove the covers.  
Do not operate this product unless the stand is attached.  
Do not connect or disconnect this product during an electrical storm.  
The power cord plug must be connected to a properly wired and grounded power outlet.  
Any equipment to which this product will be attached must also be connected to properly wired and grounded  
power outlets.  
To isolate the monitor from the electrical supply, you must remove the plug from the power outlet. The power  
outlet should be easily accessible.  
Handling:  
Your colour monitor is heavy, so handle it with care. If heavier than 18 Kg, IBM recommends that the monitor is  
moved or lifted by two people.  
DANGER  
Pour éviter les risques d’électrocution :  
Ne retirez pas les capots du moniteur.  
Nutilisez pas ce produit si le socle nest pas fixé.  
Ne connectez, ni ne déconnectez ce produit pendant un orage.  
Le câble dalimentation doit être connecté à une prise électrique correctement mise à la terre et en bon état de  
marche.  
Tout équipement auquel ce produit est relié doit être également connecté à une prise correctement mise à la  
terre et en bon état de marche.  
Pour isoler le moniteur de la source dalimentation électrique, vous devez le débrancher de la prise électrique.  
Cette prise doit être facile daccès  
Manutention :  
Votre moniteur couleurs est lourd et doit donc être manipulé avec soin. Si son poids dépasse 18 kg, IBM vous  
conseille de le déplacer ou de le porter à deux.  
GEFAHRENHINWEIS  
Um die Gefahr eines elektrischen Schlags zu vermeiden, folgendes beachten:  
Unter keinen Umständen die Abdeckungen abnehmen.  
Das Produkt nicht in Betrieb nehmen, wenn der Sockel nicht montiert ist.  
Das Gerät nicht während eines Gewitters an eine Steckdose anschließen oder von ihr trennen.  
Das Netzkabel ist an eine ordnungsgemäß verdrahtete und geerdete Steckdose anzuschließen.  
Jedes Gerät, mit dem dieses Produkt verbunden wird, muß ebenfalls an eine ordnungsgemäß verdrahtete und  
geerdete Steckdose angeschlossen werden.  
Um den Monitor von der Stromversorgung zu trennen, muß der Stecker aus der Steckdose gezogen werden.  
Die Steckdose sollte leicht zugänglich sein.  
Handhabungshinweis:  
Ihr Farbbildschirm ist schwer, gehen Sie vorsichtig damit um. Wenn er schwerer als 18 kg ist, empfiehlt IBM, daß  
der Bildschirm von zwei Personen getragen bzw. gehoben wird.  
GEVAAR  
Ga als volgt te werk om het gevaar van een elektrische schok te voorkomen:  
Verwijder in geen enkel geval de kap.  
Stel dit produkt alleen in werking als de voet is bevestigd.  
Sluit dit apparaat niet aan op, of verbreek de aansluiting van dit apparaat niet van een contactdoos tijdens  
onweer.  
Het netsnoer moet worden aangesloten op een geaarde contactdoos met correcte bedrading.  
Ook alle apparatuur waarop dit produkt wordt aangesloten moet zijn aangesloten op een contactdoos met  
correcte bedrading.  
Om het beeldscherm te ontkoppelen van de netvoeding, dient u de stekker uit de contactdoos te trekken. De  
contactdoos dient goed toegankelijk te zijn.  
Verplaatsing:  
De kleurenmonitor is zwaar. Doe dus voorzichtig. Indien de monitor zwaarder is dan 18 kilo, raadt IBM aan de  
monitor door twee mensen te laten tillen.  
FARE  
Slik unngår du fare for elektrisk støt:  
Ikke ta av dekslene.  
Ikke bruk produktet dersom sokkelen ikke er  
montert.  
Ikke koble produktet til eller fra under tordenvær.  
Pluggen på strømledningen må kobles til korrekt montert og jordet strømuttak.  
Utstyr som dette produktet eventuelt blir koblet til, må også kobles til korrekt montert og jordet strømuttak.  
For å isolere skjermen fra strømkilden må du ta ut pluggen fra strømuttaket. Strømuttaket bør være lett  
tilgjengelig.  
Käsittely:  
Värinäyttö on painava, joten käsittele sitä varoen. Jos näyttö painaa enemmän kuin 18 kg, IBM suosittelee, että  
kaksi henkilöä siirtää tai nostaa sitä.  
Varning - livsfara  
För att undvika risk för elektriska stötar måste du tänka på följande:  
Ta inte bort några skyddskåpor.  
Använd inte den här produkten innan du har satt fast stativet.  
Anslut inte produkten till ett eluttag under åskväder. Koppla inte heller ur produkten från ett eluttag under  
åskväder.  
Strömkabeln måste anslutas till ett felfritt och jordat uttag.  
All utrustning som den här produkten kopplas till måste också anslutas till felfria och jordade uttag.  
För att bryta strömmen till bildskärmen måste du dra ut kontakten. Vägguttaget bör vara lätt att komma åt.  
Hantering:  
Hantera din färgmonitor med försiktighet, den är tung. Ni bör vara två personer för att lyfta och flytta monitorn om  
den är tyngre än 18 kg.  
VAARA  
Sähköiskun vaaran välttämiseksi:  
Älä avaa laitteen kansia missään tilanteessa.  
Älä käytä laitetta, ellei jalustaa ole kiinnitetty.  
Älä kytke laitetta pistorasiaan tai irrota sitä pistorasiasta ukonilman aikana.  
Virtajohto on kytkettävä asianmukaisesti johdotettuun ja maadoitettuun pistorasiaan.  
Kaikki muutkin laitteet, joihin tämä tuote on liitetty, on kytkettävä asianmukaisesti johdotettuihin pistorasioihin.  
Kun haluat erottaa näyttimen sähköverkosta, sinun pitää irrottaa sen verkkojohto pistorasiasta. Pistorasian  
pitäisi olla mahdollisimman lähellä näytintä ja vaivattomasti käsillä.  
Håndtering:  
Fargeskjermen din er tung, og må håndteres med varsomhet. Hvis den veier mer enn 18 kilo, anbefaler IBM at  
skjermen flyttes eller løftes av to personer.  
TEHLIKE  
Elektrik çarpmasý tehlikesinden kaçýnmak için:  
Kapaklarý çýkarmayýnýz.  
Bu cihazý kaidesine takýlý durumda deðilken çalýþtýrmayýnýz.  
Bu cihazý elektriksel fýrtýna sýrasýnda prize takmayýnýz veya prizden çýkarmayýnýz.  
Elektrik kablosunun fiþi, elektrik ve toprak baðlantýlarý usulüne uygun olarak yapýlmýþ bir prize takýlmalýdýr.  
Bu cihazýn baðlanacaðý diðer tüm cihazlar da elektrik ve toprak baðlantýlarý usulüne uygun olarak yapýlmýþ prize  
takýlmýþ olmalýdýr.  
Monitörün elektrikle baðlantýsýný kesmek için fiþini prizden çekmeniz gereklidir. Priz, kolayca eriþilebilecek bir yerde  
olmalýdýr.  
Kaldýrma  
Renklý monitörünüz aðýr olduðu icin kaldýrýrken dikkatli olunuz. IBMmonitörün aðýrlýðýnýn 18 kilogramdan fazla  
olmasý halinde iki kiþi tarafýndan taþýnmasýný veya kaldýrýlmasýný tavsiye etmektedir.  
OPREZ  
Da biste izbjegli opasnost od strujnog udara:  
Nemojte otvarati kucište uredaja.  
Nemojte upotrebljavati ovaj uredaj dok ne postavite postolje.  
Nemojte spajati i odspajati uredaj za vrijeme oluje.  
Naponski kabel mora biti prikljucen u odgovarajuce uzemljenu uticnicu.  
Bilo koja oprema na koju ce ovaj uredaj biti spojen takoder mora biti prikljucena u odgovarajuce uzemljenu  
uticnicu.  
Da biste iskljucili uredaj iz struje, iskopcajte utikac iz uticnice. Uticnica treba biti lako dostupna.  
Rukovanje:  
Vaš monitor je te ak, zato rukujte njime pa ljivo. IBM preporuca da ovaj monitor podi u ili pomicu dvije osobe.  
First Edition (November 2000)  
This publication could contain technical inaccuracies or typographical  
errors. Changes are made periodically to the information herein; these  
changes will be made in later editions. IBM may make improvements  
and/or changes in the product(s) and/or program(s) at any time.  
It is possible that this publication may contain reference to, or  
information about, IBM products (machines and programs),  
programming, or services that are not announced in your country.  
Requests for copies of this publication and for technical information  
about IBM products should be made to your IBM Authorized Dealer or  
IBM Retailer.  
No part of this publication may be reproduced or distributed in any  
form or by any means without prior permission in writing from the  
International Business Machines Corporation.  
© Copyright International Business Machines Corporation 2000.  
All rights reserved.  
Note to U.S. Government Users -- Documentation related to restricted  
rights -- Use, duplication or disclosure is subject to restrictions set forth  
in GSA ADP Schedule Contract with IBM Corp.  
Notices  
References in this publication to IBM products, programs, or services  
do not imply that IBM intends to make these available in all countries  
in which IBM operates. Any reference to an IBM product, program or  
service is not intended to state or imply that only IBM’s product,  
program, or service may be used. Any functionally equivalent product,  
program, or service that does not infringe any of IBM’s intellectual  
property rights or other legally protectable rights may be used instead  
of the IBM product, program, or service. Evaluation and verification of  
operation in conjunction with other products, programs, or services,  
except those expressly designated by IBM, are the user’s  
responsibility.  
IBM may have patents or pending patent applications covering subject matter  
in this document. The furnishing of this document does not give you any  
license to these patents.  
1
Trademarks  
The following terms, used in this publication, are trademarks or service  
marks of the IBM Corporation in the United States, other countries, or  
both:  
HelpCenter  
IBM  
ENERGY STAR is a U.S. Govt. registered trademark.  
Microsoft and Windows are trademarks of Microsoft Corporation in the  
United States, other countries, or both.  
Other company, product, and service names may be trademarks or  
service marks of others.  
2
Contents  
3
4
Packing list -----------------------------------------------------  
Precautions -----------------------------------------------------  
5
5
6
6
Installation Instructions -------------------------------------  
Swivel Base ---------------------------------------------------  
Power cord --------------------------------------------------  
Video cable --------------------------------------------------  
7
7
8
9
Operating Instructions ---------------------------------------  
General Instructions ---------------------------------------  
How to adjust a setting ------------------------------------  
Adjusting the picture --------------------------------------  
10  
10  
11  
Features ---------------------------------------------------------  
Green monitor ----------------------------------------------  
Plug and play -----------------------------------------------  
12  
Technical Support (FAQ) -----------------------------------  
14-15  
16  
Appendix A – Specifications----------------------------------  
Appendix B – Factory Preset Timing Table --------------  
PACKING LIST  
The product package should include the following items:  
1. Monitor  
2. Owner's manual  
3. Power cord  
4. Swivel base  
5. Diskette  
3
PRECAUTIONS  
Workplace preparation  
Positioning the monitor  
Choose a suitable place to position the monitor where it is not near  
fluorescent desk lighting or any equipment that produces magnetic fields that  
could cause interference. Ensure that the furniture or equipment can support  
the weight of the monitor. Allow at least 2 in. (50 mm) ventilation space  
around the monitor.  
Height  
The monitor should be positioned so that the top of the screen is slightly  
below your eye level when you sit at your workstation.  
Orientation  
Choose a position that gives the least reflection from lights and windows,  
usually at a right angle to any windows. Position the monitor directly in front  
of you so that you do not have to twist your body. Tilt the monitor to a  
comfortable viewing angle.  
4
Working Practices  
Rest  
Take regular breaks. Vary your posture, and stand up and stretch  
occasionally, as prolonged use of computer workstations can be tiring.  
Back  
Sit back in the chair and use the back rest.  
Hands  
Use a light touch on the keyboard, keeping your hands and fingers relaxed.  
Allow a space in front of the keyboard to rest your wrists when not typing.  
Consider using a wristpad.  
Eyesight  
Working with monitors, in common with any prolonged close work, can be  
visually demanding. Look away from the screen periodically and have your  
eyesight checked regularly.  
Screen settings  
Set the screen brightness and contrast to a comfortable level. You might have  
to adjust this as the lighting changes during the day. Many application  
programs let you select color combinations which can help you to view in  
comfort.  
INSTALLATION INSTRUCTIONS  
Swivel Base  
To attach the swivel base to the monitor, do the following:  
Carefully turn the monitor on its side or upside down. (see figure 1)  
Locate the cavities at the bottom front of the monitor.  
Insert the pegs on the swivel base into these cavities. Push the swivel base  
forward until the swivel base locks in place.  
To remove the swivel base, hold the bottom of the swivel base, and then  
push it out.  
Install  
Remove  
Figure 1 Installing and removing the Swivel Base  
5
Power Source:  
1. Make sure the power cord is the correct type that is required in your area.  
2. This monitor has a universal power supply that allows operation in  
100/120V ac or 220/240V ac voltage (No user adjustment is required)  
3. Connect the power cord into your monitor’s power input socket, and then  
plug the other end into a 3-pin ac power outlet. The power cord can be  
connected to either a wall power outlet or the power outlet socket on your  
computer, depending on the type of power cord supplied with your  
monitor.  
Power cord:  
For safe operation, use the power cord supplied with the unit.  
Video cable  
Connecting the video cable: The monitor comes with a built-in video cable.  
Plug the signal cable's 15-pin connector into the computer's video port and  
tighten the two screws on the cable connector. (see figure 2)  
Connecting the power cord: Plug the power cord into the monitor's ac  
power socket. Then plug the power cord into a grounded ac outlet or UL-  
approved power strip or the power output socket on your computer.  
Caution: If the AC outlet is not grounded(only two holes), install the proper  
grounding adapter (not supplied).  
Diskette: The Installation Diskette included with your monitor contains  
information that you might need for its use. Refer to the readme file on this  
diskette.  
2
1
Figure 2 Connecting cables  
1.  
Power Cord  
2.  
Signal Cable  
6
OPERATING INSTRUCTIONS  
General Instructions  
The power switch is located at front panel of the monitor. Press the power  
switch to turn the monitor on or off. The other controls are located at the base  
of the monitor (See Figure 3). By changing these settings, the picture can be  
adjusted to your personal preferences.  
The power cord must be connected.  
Connect the video cable from the monitor to the System/Video card.  
To turn the monitor on, press the POWER switch to ON position. The  
power indicator will light up.  
6
7
8
9
10  
11  
12  
13  
1
2
3
4
5
Figure 3  
External Controls  
External Controls  
Switch:  
1. Power On/Off Switch  
2. LED  
Functions:  
6. Contrast  
7. Brightness  
8. H-Size  
11.  
12.  
13.  
V-Center  
Pincushion  
Trapezoid  
3. Up Key  
4. Down Key  
5. Function Key  
9. H-Center  
10. V-Size  
12+13. Rotation  
7
Notes  
Do not install the monitor in a location near heat sources such as radiators  
or air ducts , or in a place subject to direct sunlight , or excessive dust or  
mechanical vibration or shock.  
Save the original shipping carton and packing materials, as they will come  
in handy if you ever have to ship your monitor.  
To keep the monitor looking new, periodically clean it with a soft cloth.  
Stubborn stains may be removed with a cloth lightly dampened with a  
mild detergent solution. Never use strong solvents such as thinner,  
benzene, or abrasive cleaners, since these will damage the cabinet. As a  
safety precaution, always unplug the monitor before cleaning it.  
How to adjust a setting  
1. Press the ON/OFF button, the green LED lights and the power is ON.  
Press this ON/OFF button again, the green LED disappear and the power  
is OFF.  
2. When press the “FUNC” key, the LED will flash to indicate the function  
has been selected.  
3. When function has been selected, press to adjust picture image.  
4. Press the “FUNC” key until the LEDs of pincushion and trapezoid flash  
simultaneously, then press Up or Down key to adjust the picture tilt to  
horizontal position.  
8
Adjusting the picture  
The description for function control LEDS  
1.  
2.  
3.  
CONTRAST  
Adjust the picture contrast.  
BRIGHTNESS Adjust the picture brightness.  
H-SIZE  
Adjust the picture’s horizontal size.  
4.  
5.  
6.  
7.  
H-CENTER  
V-SIZE  
Adjust the horizontal position of the picture.  
Adjust the picture’s vertical size.  
V-CENTER  
Adjust the vertical position of the picture.  
PINCUSHION Adjust the pincushion and barrel.  
8.  
9.  
TRAPEZOID  
ROTATION  
RECALL  
Adjust the picture’s trapezoid distortion.  
Adjust the picture tilt to horizontal position.  
To recall original factory preset mode.  
10.  
+
9
FEATURES  
Green monitor  
The monitor has a power saving function that conforms to the VESA  
DPMS standard. This feature will only work if your computer is a “green”  
computer. This feature will switch off your monitor to conserve energy,  
after a user-specified period of inactivity.  
To activate this feature in Microsoft® Windows® 98:  
In Windows® 98, this feature can be activated and customized under the  
screen saver setting of the display properties.  
1. Using the right mouse button, click the desktop and then select  
Properties.  
2. Click the Screen Saver tab. If your system supports a “green” computer,  
the Energy Saving Features of Monitor panel displays. If your system  
does not support a “green” computer, you will have to manually turn off  
the computer to save energy.  
3. In the Energy Saving Features of Monitor panel, activate the Standby  
feature by placing a check in the Standby check box or activate the Shut  
off feature by placing a check in the Shut off check box.  
4. You can specify the amount of inactive time before your monitor enters  
standby mode or shuts off.  
The power-saving mode is indicated by the light-emitting diode (LED) on  
the front panel:  
Signal  
Power  
Mode  
On*  
Stand-by Attached  
Suspend Attached Yes  
Off Attached No  
Cable H-Sync V-Sync Video Indicator Consumption  
Attached Yes  
No  
Yes  
Yes  
No  
Active Green  
Blank Orange  
Blank Orange  
Blank Orange  
75 W  
15 W  
15 W  
No  
8 W  
10  
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF  
THERE IS NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS  
MONITOR TO OPERATE PROPERLY, THERE MUST BE A VIDEO  
INPUT SIGNAL.  
This monitor meets the Power Management standards as set by the Video  
Electronics Standards Association (VESA) and/or the United States  
Environmental Protection Agency (EPA) and The Swedish Confederation  
Employees (NUTEK). This feature is designed to conserve electrical energy  
by reducing power consumption when there is no video input signal present.  
When there is no video input signa, this monitor, following a time-out period,  
will automatically switch to an OFF mode. This reduces the monitor's internal  
power supply consumption. After the video input signal is restored, full power  
is restored and the display is automatically redrawn. The appearance is similar  
to a "Screen Saver" feature except the display is completely off. The display  
is restored by pressing a key on the keyboard, or clicking the mouse.  
Plug and play  
Plug & Play DDC1/2B Feature  
This monitor is equipped with VESA DDC1/2B capabilities according to the  
VESA DDC STANDARD. It allows the monitor to inform the host system of  
its identity and, depending on the level of DDC used, communicate additional  
information about its display capabilities. The communication channel is  
defined in two levels, DDC1 and DDC2B.  
The DDC1 is a unidirectional data channel from the display to the host that  
continuously transmits EDID information. The DDC2B is a bidirectional data  
channel based on the I²C protocol. The host can request EDID information  
over the DDC2B channel.  
11  
TECHNICAL SUPPORT (FAQ)  
Problem & Question  
Power LED is not on  
Possible Solution  
*Verify that the power switch is in the ON  
position  
*Power cord must be connected  
*Verify that the computer system is Plug &  
Play compatible  
No Plug & Play  
*Verify that the video card is Plug & Play  
compatible  
*Verify that the D-15 plug pin of video  
cable is bent  
*Make sure the monitor device drivers are  
installed  
No picture  
*Computer power switch must be in the  
ON position  
*Computer video card must be snugly  
seated in its slot  
*The signal cable must be completely  
connected to the computer  
*Check the color of the power LED  
indicator. If it is orange, then the monitor  
and the computer system are in power-  
saving mode. You need to press your  
keyboard or move the mouse to  
reactivate the system.  
Picture is fuzzy  
*Adjust the Contrast and Brightness  
Controls.  
Picture bounces or a wave pattern *Move electrical devices that might cause  
is present in the picture electrical interference.  
Monitor is stuck in “Power Saving *Make sure monitor’s video cable is  
Mode”  
properly connected to the computer.  
*Inspect monitor’s video cable and make  
sure none of the pins are bent.  
*Make sure computer is operational by  
hitting the CAPS LOCK key on the  
keyboard while observing the CAPS  
LOCK LED. The LED should either  
turn ON or OFF after hitting the CAPS  
LOCK key.  
Missing one of the primary colors *Inspect the monitor’s video cable and  
(RED, GREEN, or BLUE) make sure that none of the pins are bent.  
12  
Help and service information  
This section contains information on how to obtain online and telephone technical  
support.  
Online technical support  
Online technical support is available during the life of your product. Online assistance  
can be obtained through the Personal Computing Support Web site and the IBM  
Automated Fax System.  
Online technical support  
IBM Personal Computing Support Web  
site  
http:/ / www.ibm.com/ pc/ support  
During the warranty period, assistance for replacement or exchange of defective  
components is available. In addition, if your IBM option is installed in an IBM  
computer, you might be entitled to service at your location. Your technical support  
representative can help you determine the best alternative.  
Telephone technical support  
Installation and configuration support through the HelpCenter will be withdrawn or  
made available for a fee, at IBMs discretion, 90 days after the option has been  
withdrawn from marketing. Additional support offerings, including step-by-step  
installation assistance, are available for a nominal fee.  
If you are unable to correct the problem yourself contact your dealer, retailer, or other  
IBM authorized service. Support phone numbers are also available by clicking HelpCenter  
phone list on the IBM support Web page at  
Before calling, please have available as much of the following information as possible:  
1. Type, model and serial number fron the label on the back of your monitor.  
2. Purchase receipt.  
3. Description of problem.  
4. Computer type and model.  
5. System configuration(hardware fitted etc.)  
6. System BIOS version number.  
7. Operating System and version number  
8. Display driver version number.  
APPENDIX A – SPECIFICATIONS  
CRT Size  
35.5 cm (14 in.), 90º deflection,  
29 mm neck  
CRT  
Input  
Viewable Image 33.5 cm (13.2 in.), diagonal  
Size  
Type  
0.28 mm dot pitch.  
Video  
0.7 Vpp, R,G,B Analog  
Separate Sync. TTL Level  
H./V.- Sync.  
H-Frequency  
V-Frequency  
Positive / Negative  
30 - 54 kHz  
50 - 120 Hz  
Scanning  
Frequency  
Max. Resolution  
Video dot rate  
1024 x 768  
65 MHz  
Factory Preset mode :  
User Programmable mode :  
Power Source  
7
12  
Universal 100 – 240 V ac,  
50 Hz / 60 Hz  
Operating  
Humidity  
Dimensions  
0 to 40º C (0 to 104º F)  
10% to 85% relative, non-condensing  
424 mm (1.39 ft) × 424 mm (1.39 ft)  
× 455 mm (1.5 ft) (W × H × D)  
Carton  
Monitor & Base 350 mm (1.14 ft) × 349 mm (1.15 ft)  
× 377 mm (1.2 ft) (W × H × D)  
Weight  
Unit (net)  
Carton (gross) 12.0 kg ( Gross )  
Attached Mini D-sub 15 Male  
10.4 kg ( Net )  
Signal Cable:  
350  
377  
Unit: mm  
14  
Switch  
Power On/Off switch  
Up/Down Key  
Function Key  
Contrast  
External Controls:  
Functions  
Brightness  
H-Size  
H-Center  
V-Size  
V-Center  
Pincushion  
Trapezoid  
Rotation  
Plug & Play  
DDC1/2B  
Power Management  
EPA, VESA DPMS  
75 W  
250 mm (9.84 in.) x 187 mm (7.36 in.)  
UL, FCC, CE, MPR II, FDA, CSA  
Power Consumption ( Maximum )  
Pre-set Display Area  
Regulatory  
Compliance  
15  
APPENDIX B – FACTORY PRESET TIMING TABLE  
HORIZONTAL  
FREQUENCY  
VERTICAL  
FREQUENCY  
STANDARD  
RESOLUTION  
IBM  
720 × 400  
640 × 480  
640 × 480  
640 × 480  
800 × 600  
800 × 600  
1024 × 768  
31.5 kHz  
31.5 kHz  
37.5 kHz  
43.3 kHz  
46.9 kHz  
53.7 kHz  
48.4 kHz  
70 Hz  
60 Hz  
75 Hz  
85 Hz  
75 Hz  
85 Hz  
60 Hz  
VGA  
VESA/75  
VESA/85  
VESA/75  
VESA/85  
VESA/75  
Connector pin assignment  
1
6
5
10  
11  
15  
15 - Pin Color Display Signal Cable  
PIN NO.  
DESCRIPTION  
PIN NO.  
DESCRIPTION  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
Red  
Green  
Blue  
Ground  
Ground  
R-Ground  
G-Ground  
B-Ground  
9.  
10.  
11.  
12.  
13.  
14.  
15.  
NC  
Ground  
Monitor Ground  
DDC-Serial Data  
H-Sync  
V-Sync / V-CLK  
DDC-Serial Clock  
For DDC  
16  
版本1  
该版本可能包含了技术上的不精确性或印刷上的错误,故此,将定  
期进行修改,这些改动将载入到新版本的编辑中,IBM将于任何时候改  
善和/或变更此版本中述及的产品和/或程序。  
该版本可能包含有某些不在您的国家颁布的有关IBM产品程序服务  
的参考资料或信息。  
需要此版本的复印件或有关IBM产品的技术信息,请洽询IBM授权  
经销商或零售商。  
该版本在未经国际商业机器公司预先的书面允许前,不准以任何形  
式或途径复制和发布。  
© 国际商业机器公司版权所有 2000  
对美国政府使用人员 -- 文件相关限制权利 -- 使用、复制及泄露限制依  
先前与IBM所签的GSA ADP Schedule Contract的规定。  
注意  
该版本里关于IBM产品、程序或服务的参考资料并非意味IBM  
会使这些资料在所有IBM运作的国家里都能得到。任何涉及IBM的  
产品、程序或服务,并非说明或意味着只有IBM的产品、程序或服务  
才可以使用。任何功能相当的产品、程序或服务,只要不侵犯IBM  
的知识产权或其他受法律保护的权利,均可以使用。使用者应自己  
负责对非IBM产品、程序或服务进行评估和确认。  
在该文件里,IBM可能有覆盖各主要方面的专利或待申请的专利,  
提供此份印刷品并不提供使用有关专利的权利。  
1
商标  
下述应用于该版本的条款是IBM公司在美国或其他国家的商标或服  
务标记:  
IBM  
能源之星是美国政府注册标志。  
MicrosoftWindows是微软公司在美国其或他国家,或者是两者的商标。  
其它公司、产品及服务的名称,可能是他们的商标或服务标记  
2
目录  
包装清单 --------------------------------------------------------  
3
4
预防措施 --------------------------------------------------------  
5
5
6
安装说明 --------------------------------------------------------  
转盘底座------------------------------------------------------  
电源线 -------------------------------------------------------  
6
信号线 -------------------------------------------------------  
7
7
7
8
9
操作说明 -------------------------------------------------------  
一般说明------------------------------------------------------  
前面板控制 --------------------------------------------------  
调整设置 ----------------------------------------------------  
调整----------------------------------------------------  
10  
10  
11  
特征 ------------------------------------------------------------  
绿色显示--------------------------------------------------  
即插即------------------------------------------------------  
12  
技术支持(FAQ----------------------------------------------  
14-15  
16  
A----------------------------------------------------  
B-工厂置模-------------------------------------  
包装清单  
包装箱内含有以下品:  
1. 显示器  
2. 说明书  
3. 电源线  
4. 转盘底座  
5. 安装盘  
3
预防措施  
备工地点  
置显示器  
选择个合适位置置显示器,不要靠近荧光台灯或产生磁场  
器,它们会引起干涉。确定放置显示器的物体可以受它的重量。  
显示器的周围至少需要两英寸(50毫米)通风空间。  
放置高度  
当您在您的前,显示屏幕顶部于您视力水  
平位置。  
放置向  
选择个由灯光窗口反射最少位置通常对于任意窗口都应在  
个合适角度了不您转动身体显示器应放置在您的前方。将  
显示倾斜放置到一个视线服的位置。  
4
实践  
: 使用计算机时,可使用不姿势站立伸腰来解  
从而得到息。  
靠背: 椅子,并利用靠背休息  
:  
把手轻轻放盘上,让手手指放松,当不必打字时,在键  
盘前为手腕留空间,以便手腕休息。可以考使用腕垫)  
视觉: 间近距离使用显示器,易造成视觉疲劳,要经常把眼睛  
从显示屏移开,以保护视力,并定期检查视力。  
屏幕设置: 把屏幕亮度及对比度设至最佳状态,许应用程序允许您  
选择颜色,这可使您视觉处最舒适状态。  
安装说明  
转盘底座  
要安装底盘,请以下的步骤做:  
 
(
)  
对  
 
,
,
若对若  
,
,
,
安装  
拆卸  
一  
底盘安装  
5
电源:  
1. 先确认该电源线符合您所使用的地区标准。  
2. 显示器有较宽的电源电压工范围,可使用于100 / 120V AC或  
220 / 240V AC地区(无需用节)。  
3. 电源线一端插显示器电源座,端接外部三芯插座。  
电源线:  
了安操作,请使用提供的电源线。  
信号线  
信号线联接:本显示有一内嵌信号线。15针插头接PC显示卡  
输出口,并用螺丝锁好(见图2)  
电源线联接:电源线一端插显示后部座中,端插PC墙  
上的电源座里。  
注意:电源座未接地,必须安装确的接地适配(未提供),以保证  
。  
盘:您在操作显示器时所要了的信息。请查阅磁盘中自  
述文件。  
2
1
图二  
联接线  
2.  
1.  
电源线  
信号线  
6
操作说明  
一般说明  
电源关和其它控制按键位显示器前面板(见图三)。使用电源关,  
可以打开或关闭显示器。通过这些按键得到您需要的面。  
接  
小对  
PC  
把  
ON位置,电源指示灯亮  
6
7
8
9
10  
11  
12  
13  
1
2
3
4
5
图三  
外部控制按键  
外部控制  
:  
功能:  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
9.  
10.  
11.  
12.  
13.  
12+13.  
电源关  
指示灯  
增大键  
减小键  
功能键  
比度  
亮度  
水平尺寸  
水平心  
垂直尺寸  
垂直心  
形或失真  
失真  
转  
7
注意  
1. 不要把显示靠近热源的方,如取暖器、气管光直射的  
方。不要灰尘过多或者机械振动、冲击方。  
2. 包装料,要运您的显示器,它们会给  
带来便利。  
3. 持显示,要定期的用软布它,顽迹可用和  
的清洁剂去除,不要用强烈的清洁剂稀释剂腐蚀性的清  
洁剂这些东西损伤全起见,清前要拔掉电源  
插头。  
调整设置  
1. 下电源关,绿色指示灯亮,电源接通。  
绿色指示灯熄灭,电源。  
2. 下功能指示灯闪烁显示选择的功能。  
3. 按大小键节选择的功能改变面。  
4. 功能键直至枕形和形两指示灯同后按增大减小键调  
倾斜偏差。  
8
调整面  
功能述  
1.  
比度  
亮度  
节画面对比度。  
节画亮度。  
2.  
3.  
水平尺寸  
节画水平尺寸。  
4.  
5.  
6.  
7.  
水平心  
垂直尺寸  
垂直心  
节画水平位置。  
节画垂直尺寸。  
节画垂直位置。  
形或失真 节画形或形变。  
8.  
9.  
失真  
转  
节画失真。  
节画倾斜偏差。  
10.  
叫  
按重工厂设。  
+
9
特征  
绿色显示器  
显示符合VESA DPMS标准的能功能,您的PC绿色  
PC,本显示成为绿色显示器。这种现象除失外其  
它方面都很象屏幕贮存器的特征。  
â
â
Microsoft Windows® 98激活特征:  
1. 使用键点一下平台后选择性。  
2. 屏幕保护说明您的系统支持绿色PC那么显示电  
显显示您的系统没支持绿色PC,您将必须电  
来节能。  
3. 显示器的特征部是两个窗口能和关。您可以激活任  
意一或两。  
4. 显示器进入状态前,您可以定或设置显示状态  
或关的时。  
状态可以通过前面板的LED显示:  
信号  
行信号  
电源  
消耗率  
式  
信号线  
接  
信号 面  
指示灯  
绿色  
*  
待机  
起  
机  
正常  
消隐  
消隐  
消隐  
75W  
15W  
15W  
接  
色  
色  
色  
接  
接  
8W  
10  
果没入信号,显示器将呈现出无功能状态了使显示器能  
确操作,必须要有入信号。  
显示符合视标准(VESA)、美国保机(EPA)瑞典  
组织(NUTEK)规定的能源标准,其功能是通过无视频  
入信号时减少能源消耗的方式来节电能的。在信号显  
器时,经,将自动切换”状态,这样就减少显  
器的内部能源消耗入信号,所用电能正常且画面  
会自动。这种现象除失外其他方面都很象“屏幕贮存  
特征显示否则通过按键盘上某一动  
标可。  
即插即用  
DDC1/2B特征  
显示配备符合 VESA DDC 标准的 VESA DDC1/2B,这允许  
显示器将其告诉主机,并根据DDC使用的标准,显示特  
性的信息。输通有两DDC1DDC2B。  
DDC1显示器到主机连续传送EDID信息的单数据DDC2  
B符合I²C定的数据,主机可以通过DDC2B道去EDI  
D信息。  
11  
技术支持(FAQ)  
问题  
可能的方法  
电源指示灯亮  
*电源关  
*否连电源线  
*计算系统即插即配  
*显示卡即插即配  
*信号线15D接头弯曲  
*显示动器程序安装  
即插即用  
无图现  
*电源关  
*显示卡放置在它的中  
*否连信号线  
*检查电源指示灯颜色显示器  
计算系统状态按键盘或鼠  
激活系统。  
*比度和明亮度  
象暗淡  
象跳动或现波纹面  
*可能引起子干的电器设备  
显示器一直处状态 *显示器的信号线计算接  
*检查显示器信号线插头并确信各脚没弯曲  
*通过按计算盘上的 Caps Lock观察指  
示灯,确认计算机是在操作。  
*检查显示器的信号线,并确信脚没弯曲  
色(绿)  
12  
支持及服务信息  
本节的内容,是关于如何取得在线及电话技术支持方面的信息。  
在线技术支持  
本公司将在产品使用期间内提供在线技术支持,你可经由  
个人演算支持网站及IBM自动传真系统获得在线帮助。  
在线技术支持  
IBM个人演算支持网站  
在保证期间,本公司将提供有关故障元件换新或更换方面的  
帮助。除此之外,如果你将另行购买IBM组件装配在IBM电  
脑上时,可能也有权利要求在贵处进行产品服务,本公司的  
技术支持代表将帮助你决定最佳的选择。  
电话技术支持  
从取消购买选择起90天内,可依IBM的决定取消经由帮助中  
心(HelpCenter)所提供的安装及配置支持,或以收费的方式  
提供。另外也可收取微薄费用的方式,提供额外的支持,其  
中包括逐步安装方面的帮助。  
如果无法自行矫正问题时,请联络当地的经销商、零售商或  
其他经IBM授权的维修中心。你可经由http://www.ibm.com/  
pc/supportIBM支持网页HelpCenter电话簿上按两次,而取  
得支持电话号码。  
在拨号前,请尽可能了解如下信息:  
1. 机型、型号和显示器后壳上标签印刷的序列号。  
2. 购买收据。  
3. 显示器有什么问题。  
4. 计算机的种类和型号。  
5. 系统的配置(硬件配置等)。  
6. 基本输入输出系统的版本号。  
7. 操作系统和版本号。  
8. 显卡驱动程序版本号。  
13  
A格  
35.5 cm (14 in.), 直角,  
29 mm 颈  
管尺寸  
线33.5 cm (13.2 in.),  
0.28 mm  
管  
视尺寸  
点距  
信号  
离同步  
拟红绿0.7 V pp  
TTL 平  
水平/垂直同步/-  
入信号  
扫描频率  
频  
30 - 54 kHz  
50 –120 Hz  
频  
1024 x 768  
65 MHz  
最高分辨率  
频  
7
12  
工厂置模式:  
户模式:  
电源  
关电源,交流100 – 240 V ac,  
50 Hz / 60 Hz  
环境温度  
湿度  
0 40(0 – 104°F)  
相对湿10%85%  
424 mm (1.39 ft) × 424 mm (1.39 ft)  
× 455 mm (1.5 ft) (W × H × D)  
350 mm (1.14 ft) × 349 mm (1.15 ft)  
× 377 mm (1.2 ft) (W × H × D)  
10.4 kg  
尺寸  
箱  
显示器和底盘  
重量  
重  
12.0 kg  
重  
15 针小D接头  
377  
信号线  
350  
Unit: mm  
14  
电源关  
关  
选择键  
功能键  
外部控制:  
功能  
比度  
亮度  
水平尺寸  
水平心  
垂直尺寸  
垂直心  
形或失真  
失真  
转  
DDC1/2B  
EPA, VESA DPMS  
最大75 W  
即插即用  
能标准  
耗  
250 mm (9.84 in.) x 187mm (7.36 in.)  
UL, FCC, CE, MPR II, FDA, CSA  
设显示尺寸  
安规  
15  
B-工厂置模表  
标准  
分辨率  
频  
频  
IBM  
720 × 400  
640 × 480  
640 × 480  
640 × 480  
800 × 600  
800 × 600  
1024 × 768  
31.5 kHz  
31.5 kHz  
37.5 kHz  
43.3 kHz  
46.9 kHz  
53.7 kHz  
48.4 kHz  
70 Hz  
60 Hz  
75 Hz  
85 Hz  
75 Hz  
85 Hz  
60 Hz  
VGA  
VESA/75  
VESA/85  
VESA/75  
VESA/85  
VESA/75  
信号线各说明  
1
6
5
10  
11  
15  
15色显示信号线  
脚  
说明  
脚  
说明  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
9.  
10.  
11.  
12.  
13.  
14.  
15.  
绿
接地  
接地  
地  
绿地  
地  
接地  
接地  
SDA(数据/线)  
水平同步信号  
垂直同步信号/(*)  
SCL(行时)  
用于 DDC  
16  
 
1
該版版該  
將期  
IBM  
或  
/
/
該版版該  
産  
IBM  
或  
該  
産  
授  
IBM  
IBM  
或  
該版  
需式或  
該  
©
2000  
文 對使需式使使文文使  
-- --  
先  
國所該  
或  
GSA ADP Schedule Contract  
IBM  
注  
該版將  
IBM  
使産  
對  
IBM  
該  
IBM  
運該或  
使或  
IBM  
該  
使或  
,
IBM  
文任使任  
的  
IBM  
産  
使或  
IBM  
産期或  
該文該  
IBM  
該  
或産或  
1
商  
將該版下  
商  
IBM  
記  
IBM  
對能或  
或  
Microsoft Windows  
,
使其商記  
2
 
包  
預  
安包並並  
-------------------------------------------------------  
-------------------------------------------------------  
-------------------------------------------------------  
-----------------------------------------------------  
------------------------------------------------------  
3
4
5
5
6
轉  
電能電  
信電  
------------------------------------------------------  
6
並  
------------------------------------------------------  
7
7
8
9
並  
調調調調  
調調該  
-----------------------------------------------------  
---------------------------------------------------  
---------------------------------------------------  
 
-----------------------------------------------------------  
10  
10  
11  
該  
對  
-------------------------------------------------  
-----------------------------------------------------  
12  
技術支援(FAQ---------------------------------------------  
14-15  
16  
附錄A-規格---------------------------------------------------  
附錄B-工廠預置模式表 -------------------------------------  
包  
記  
該  
1.  
2.  
3.  
4.  
5.  
該  
電能電  
轉  
安包轉  
3
預  
 
調該  
調調該  
調該  
或  
50  
調放放  
當  
調或  
調放  
調對將將注該  
調該  
調調或  
工  
使使該  
或  
記 該靠休或  
記  
把手把把把  
手盤手盤休毫  
從  
或  
調調調選  
或  
4
安包並並  
 
要安裝底盤,請照以下的步驟做:  
小心的把顯示器倒過來或側放(圖一)  
對準顯示器底部的卡槽  
把底盤腳插入卡槽,並把底盤向前壓,直到完全被鎖定  
若要拆底盤,則握住底盤,用力按卡勾,直到底座鬆脫  
安包  
 
一  
安包  
5
電能記  
該電能或  
1.  
電能電將  
100 / 120V AC  
2.  
調或  
220 / 240V AC  
電能電能當電或  
3.  
電能電記  
電能或  
信電  
信電記版裝本信電把 針即針的  
15 PC  
産對見圖  
(
)  
電能電能或  
PC  
電能或  
注記電能安包以  
),  
,
(
或  
磁  
或  
2
1
圖  
電  
信電  
2.  
電能電  
1.  
6
並  
並  
電能見圖電能  
調該  
.
電能電  
信電的  
調將  
調電能把綠把  
ON”  
6
7
8
9
10  
11  
12  
13  
1
2
3
4
5
電  
把  
文  
該  
該  
:
:
電能該  
把綠選  
把  
把  
把  
放  
放  
顯  
垂  
顯  
垂  
枕  
枕  
轉  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
9.  
10.  
11.  
12.  
13.  
12+13.  
7
注  
使該  
1.  
2.  
3.  
使或  
 
或  
善  
使包  
電能即  
或  
調調調調  
下電能把綠電能或  
1.  
把綠電能或  
下任把綠或  
增減調或  
把綠調  
調或  
2.  
3.  
4.  
8
調調  
或  
1.  
放  
放  
調或  
調或  
2.  
3.  
顯  
調或  
垂  
顯  
垂  
調調或  
調或  
調調或  
4.  
5.  
6.  
7.  
調或  
枕  
轉  
調或  
8.  
9.  
調或  
重  
調或  
10.  
+
9
 
 
選  
綠  
PC  
VESA DPMS  
的  
PC  
或  
â
â
記  
Microsoft Windows® 98  
使使使一下使或  
1.  
電  
PC  
2.  
開  
PC  
電能或  
將  
或  
3.  
4.  
調調把  
或  
該  
記  
LED  
信  
信  
電能  
消  
或  
該  
該  
暫  
該  
信電  
電  
該  
把綠選  
綠  
選  
消  
消  
消  
*
75W  
15W  
15W  
電  
綠  
綠  
綠  
電  
電  
8W  
10  
該  
或  
會  
使、  
和  
(EPA)  
(VESA)  
典  
當  
(NUTEK)  
期  
綠  
該  
他  
期  
使使或  
 
特  
DDC1/2B  
準首選  
該  
該  
VESA DDC  
VESA DDC1/2B  
顯  
使特  
DDC  
使該  
DDC1 DDC2B  
使是  
該  
EDID DDC2  
DDC1  
開  
I²C  
運  
EDI  
B
DDC2B  
或  
D
11  
 
FAQ  
出  
受  
電能把綠把  
電能該  
*
*
*
*
*
*
*
*
*
*
電能電  
對  
必  
必  
信電 型  
15  
D
安包  
電能該  
地圖,  
調期  
信電  
電能把綠該  
使使  
或  
圖  
調善並放  
*
*
*
*
*
,出該  
垂擇把  
調準  
信電電  
信電即針型  
該  
把綠  
Caps Lock  
或  
使使毫  
信電型  
*
12  
 
 
支  
 
支  
本  
IBM  
支  
個  
IBM  
本  
組  
IBM  
本  
IBM  
本  
支  
天  
自  
IBM  
本))  
90  
助  
HelpCenter  
面電本  
本  
若  
本  
本  
IBM  
電  
支  
HelpCenter  
com/pc/support IBM  
本  
撥  
次  
收購  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
問  
收支監  
)  
基本次  
次  
監顯監面次  
13  
 
A
一  
35.5 cm (14 in.),  
,
顯  
管  
29 mm 短  
長  
0.28 mm  
要  
顯  
長  
33.5 cm (13.2 in),  
信  
如  
使使缺  
0.7 Vpp  
信  
消  
的  
TTL  
+ -  
/
/
如  
如  
30 – 54 kHz  
50 - 120 Hz  
1024 x 768  
65 MHz  
放  
如  
調記  
記  
電能  
7
12  
電能關  
100 – 240 V ac,  
50 Hz / 60 Hz  
、環放  
放  
0 to 40º C (0 to 104º F)  
放  
10% 85%  
顯  
裝  
424 mm (1.39 ft) × 424mm (1.39 ft)  
× 455 mm (1.5 ft) (W × H × D)  
350 mm (1.14 ft) × 349 mm (1.15 ft)  
× 377 mm (1.2 ft) (W × H × D)  
10.4 kg  
轉  
儀  
儀  
儀  
12.0 kg  
信電  
顯 顯針  
15  
D
350  
377  
Unit: mm  
14  
該  
電能該  
把  
把  
放  
放  
顯  
垂  
顯  
垂  
枕  
枕  
轉  
記  
該  
對  
準  
消  
DDC1/2B  
EPA, VESA DPMS  
增  
75 W  
調顯  
250 mm (9.84 in.) x 187mm (7.36 in.)  
UL, FCC, CE, MPR II , FDA, CSA  
的  
15  
調功  
B
準  
放  
如  
如  
IBM  
720 × 400  
640 × 480  
640 × 480  
640 × 480  
800 × 600  
800 × 600  
1024 × 768  
31.5 kHz  
31.5 kHz  
37.5 kHz  
43.3 kHz  
46.9 kHz  
53.7 kHz  
48.4 kHz  
70 Hz  
60 Hz  
75 Hz  
85 Hz  
75 Hz  
85 Hz  
60 Hz  
VGA  
VESA/75  
VESA/85  
VESA/75  
VESA/85  
VESA/75  
信電並  
1
6
5
10  
11  
15  
信電  
15  
檢  
並  
檢  
並  
準  
準  
準  
準  
準  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
9.  
10.  
11.  
12.  
13.  
14.  
15.  
準  
準  
SDA(  
串機電  
)
/
信  
機  
/(*  
)
串機機  
SCL(  
將  
)
DDC  
16  
Warranty Statements  
Warranty period – Three (3) years  
Your Installation Diskette includes translation of IBM’s Statement of  
Warranty in the following languages:  
Worldwide Statement of Warranty  
(Except Turkiye, U.S., Puerto Rico and Canada):  
Arabic  
Z1255697.ara.html  
Z1255697.bra.html  
Z1255697.bul.html  
Z1255697.chi.html  
Z1255697.cro.html  
Z1255697.cze.html  
Z1255697.dan.html  
Z1255697.dut.html  
Z1255697.eng.html  
Z1255697.fin.html  
Z1255697.fre.html  
Z1255697.ger.html  
Z1255697.gre.html  
Z1255697.heb.html  
Z1255697.hun.html  
Z1255697.ita.html  
Z1255697.jap.html  
Z1255697.kor.html  
Z1255697.nor.html  
Z1255697.pol.html  
Z1255697.por.html  
Z1255697.rus.html  
Z1255697.sla.html  
Z1255697.sle.html  
Z1255697.spa.html  
Z1255697.swe.html  
Z1255697.tai.html  
Brazilian portuguese  
Bulgarian  
Chinese  
Croatian  
Czech  
Danish  
Dutch  
English  
Finnish  
French  
German  
Greek  
Hebrew  
Hungarian  
Italian  
Japanese  
Korean  
Norwegian  
Polish  
Portuguese  
Russian  
Slovakian  
Slovenian  
Spanish  
Swedish  
Taiwanese  
Turkiye Statement of Warranty:  
Z1255698.tur.html  
Turkish  
English  
Z1255698.eng.html  
United States, Puerto Rico and Canada Statement of Limited  
Warranty:  
English  
French Canadian  
Z1254753.eng.html  
Z1254753.fca.html  
1
Warranty Statements  
The warranty statements consist of two parts: Part 1 and Part 2. Part 1 varies by  
country. Part 2 is the same for both statements. Be sure to read both the Part 1 that  
applies to your country and Part 2.  
United States, Puerto Rico, and Canada (Z125-4753-05 11/97)  
(Part 1 - General Terms)  
Worldwide except Canada, Puerto Rico, Turkey, and United States  
(Z125-5697-01 11/97)  
(Part 1 - General Terms)  
Worldwide Country-Unique Terms  
(Part 2 - Country-Unique Terms)  
IBM Statement of Limited Warranty for United States,  
Puerto Rico, and Canada (Part 1 - General Terms)  
This Statement of Limited Warranty includes Part 1 - General Terms and Part 2 - Country-  
unique Terms. The terms of Part 2 may replace or modify those of Part 1 . The warranties  
provided by IBM in this Statement of Limited Warranty apply only to Machines you purchase for  
your use, and not for resale, from IBM or your reseller. The term “Machine” means an IBM  
machine, its features, conversions, upgrades, elements, or accessories, or any combination of  
them. The term “Machine” does not include any software programs, whether pre-loaded with  
the Machine, installed subsequently or otherwise. Unless IBM specifies otherwise, the following  
warranties apply only in the country where you acquire the Machine. Nothing in this Statement  
of Warranty affects any statutory rights of consumers that cannot be waived or limited by  
contract. If you have any questions, contact IBM or your reseller.  
Machine - M/T 2248 E40 Color Monitor  
Warranty Period* - Three (3) Years  
*Contact your place of purchase for warranty service information.  
Some IBM Machines are eligible for On-site warranty service  
depending on the country where service is performed.  
The IBM Warranty for Machines  
IBM warrants that each Machine 1) is free from defects in materials and workmanship and 2)  
conforms to IBM's Official Published Specifications. The warranty period for a Machine is a  
specified, fixed period commencing on its Date of Installation. The date on your sales receipt is  
the Date of Installation, unless IBM or your reseller informs you otherwise. During the warranty  
period IBM or your reseller, if approved by IBM to provide warranty service, will provide repair  
and exchange service for the Machine, without charge, under the type of service designated for  
the Machine and will manage and install engineering changes that apply to the Machine. If a  
Machine does not function as warranted during the warranty period, and IBM or your reseller are  
unable to either 1) make it do so or 2) replace it with one that is at least functionally equivalent,  
you may return it to your place of purchase and your money will be refunded. The replacement  
may not be new, but will be in good working order.  
Extent of Warranty  
The warranty does not cover the repair or exchange of a Machine resulting from misuse,  
accident, modification, unsuitable physical or operating environment, improper maintenance by  
you, or failure caused by a product for which IBM is not responsible. The warranty is voided by  
removal or alteration of Machine or parts identification labels.  
2
THESE WARRANTIES ARE YOUR EXCLUSIVE WARRANTIES AND  
REPLACE ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR  
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS  
FOR A PARTICULAR PURPOSE. THESE WARRANTIES GIVE YOU  
SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS  
WHICH VARY FROM JURISDICTION TO JURISDICTION. SOME  
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF  
EXPRESS OR IMPLIED WARRANTIES, SO THE ABOVE EXCLUSION OR  
LIMITATION MAY NOT APPLY TO YOU. IN THAT EVENT, SUCH  
WARRANTIES ARE LIMITED IN DURATION TO THE WARRANTY  
PERIOD. NO WARRANTIES APPLY AFTER THAT PERIOD.  
Items Not Covered by Warranty  
IBM does not warrant uninterrupted or error-free operation of a Machine. Unless specified  
otherwise, IBM provides non-IBM machines WITHOUT WARRANTIES OF ANY  
KIND.  
Any technical or other support provided for a Machine under warranty, such as assistance via  
telephone with “how-to” questions and those regarding Machine set-up and installation, will be  
provided WITHOUT WARRANTIES OF ANY KIND.  
Warranty Service  
To obtain warranty service for the Machine, contact your reseller or IBM. In the United States,  
call IBM at 1-800-772-2227. In Canada, call IBM at 1-800-565-3344. You may be required to  
present proof of purchase.  
IBM or your reseller provides certain types of repair and exchange service, either at your  
location or at a service center, to keep Machines in, or restore them to, conformance with their  
Specifications. IBM or your reseller will inform you of the available types of service for a  
Machine based on its country of installation. IBM may repair the failing Machine or exchange it  
at its discretion.  
When warranty service involves the exchange of a Machine or part, the item IBM or your  
reseller replaces becomes its property and the replacement becomes yours. You represent that all  
removed items are genuine and unaltered. The replacement may not be new, but will be in good  
working order and at least functionally equivalent to the item replaced. The replacement assumes  
the warranty service status of the replaced item.  
Any feature, conversion, or upgrade IBM or your reseller services must be installed on a  
Machine which is 1) for certain Machines, the designated, serial-numbered Machine and 2) at an  
engineering-change level compatible with the feature, conversion, or upgrade. Many features,  
conversions, or upgrades involve the removal of parts and their return to IBM. A part that  
replaces a removed part will assume the warranty service status of the removed part.  
Before IBM or your reseller exchanges a Machine or part, you agree to remove all features,  
parts, options, alterations, and attachments not under warranty service.  
You also agree to  
1. ensure that the Machine is free of any legal obligations or restrictions that prevent its  
exchange;  
2. obtain authorization from the owner to have IBM or your reseller service a Machine that  
you do not own; and  
3. where applicable, before service is provided  
3
a.  
follow the problem determination, problem analysis, and service request procedures  
that IBM or your reseller provides, b. secure all programs, data, and funds contained  
in a Machine,  
b. provide IBM or your reseller with sufficient, free, and safe access to your facilities to  
permit them to fulfill their obligations, and  
c.  
inform IBM or your reseller of changes in a Machine's location.  
IBM is responsible for loss of, or damage to, your Machine while it is 1) in IBM's possession or  
2) in transit in those cases where IBM is responsible for the transportation charges.  
Neither IBM nor your reseller is responsible for any of your confidential, proprietary or personal  
information contained in a Machine which you return to IBM or your reseller for any reason.  
You should remove all such information from the Machine prior to its return.  
Production Status  
Each IBM Machine is manufactured from new parts, or new and used parts. In some cases, the  
Machine may not be new and may have been previously installed. Regardless of the Machine's  
production status, IBM's appropriate warranty terms apply.  
Limitation of Liability  
Circumstances may arise where, because of a default on IBM's part or other liability, you are  
entitled to recover damages from IBM. In each such instance, regardless of the basis on which  
you are entitled to claim damages from IBM (including fundamental breach, negligence,  
misrepresentation, or other contract or tort claim), IBM is liable for no more than  
1. damages for bodily injury (including death) and damage to real property and tangible  
personal property; and  
2. the amount of any other actual direct damages, up to the greater of U.S. $100,000 (or  
equivalent in local currency) or the charges (if recurring, 12 months' charges apply) for the  
Machine that is the subject of the claim.  
This limit also applies to IBM's suppliers and your reseller. It is the maximum for  
which IBM, its suppliers, and your reseller are collectively responsible.  
UNDER NO CIRCUMSTANCES IS IBM LIABLE FOR ANY OF THE  
FOLLOWING: 1) THIRD-PARTY CLAIMS AGAINST YOU FOR  
DAMAGES (OTHER THAN THOSE UNDER THE FIRST ITEM LISTED  
ABOVE); 2) LOSS OF, OR DAMAGE TO, YOUR RECORDS OR DATA; OR  
3) SPECIAL, INCIDENTAL, OR INDIRECT DAMAGES OR FOR ANY  
ECONOMIC CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS  
OR SAVINGS), EVEN IF IBM, ITS SUPPLIERS OR YOUR RESELLER IS  
INFORMED OF THEIR POSSIBILITY. SOME JURISDICTIONS DO NOT  
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR  
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR  
EXCLUSION MAY NOT APPLY TO YOU.  
IBM Statement of Warranty Worldwide except Canada,  
Puerto Rico, Turkey, United States (Part 1 -General Terms)  
This Statement of Warranty includes Part 1 - General Terms and Part 2 - Country-unique Terms.  
The terms of Part 2 may replace or modify those of Part 1 . The warranties provided by IBM  
in this Statement of Warranty apply only to Machines you purchase for your use, and not for  
resale, from IBM or your reseller. The term “Machine” means an IBM machine, its features,  
conversions, upgrades, elements, or accessories, or any combination of them. The term  
“Machine” does not include any software programs, whether pre-loaded with the Machine,  
4
installed subsequently or otherwise. Unless IBM specifies otherwise, the following warranties  
apply only in the country where you acquire the Machine. Nothing in this Statement of Warranty  
affects any statutory rights of consumers that cannot be waived or limited by contract. If you  
have any questions, contact IBM or your reseller.  
Machine –M/T 2248 E40 Color Monitor  
Warranty Period* - Three (3) Years  
*Contact your place of purchase for warranty service information. Some IBM Machines  
are eligible for On-site warranty service depending on the country where service is  
performed.  
The IBM Warranty for Machines  
IBM warrants that each Machine 1) is free from defects in materials and workmanship and 2)  
conforms to IBM's Official Published Specifications. The warranty period for a Machine is a  
specified, fixed period commencing on its Date of Installation. The date on your sales receipt is  
the Date of Installation, unless IBM or your reseller informs you otherwise.  
During the warranty period IBM or your reseller, if approved by IBM to provide warranty  
service, will provide repair and exchange service for the Machine, without charge, under the type  
of service designated for the Machine and will manage and install engineering changes that  
apply to the Machine. If a Machine does not function as warranted during the warranty period,  
and IBM or your reseller are unable to either 1) make it do so or 2) replace it with one that is at  
least functionally equivalent, you may return it to your place of purchase and your money will be  
refunded. The replacement may not be new, but will be in good working order.  
Extent of Warranty  
The warranty does not cover the repair or exchange of a Machine resulting from misuse,  
accident, modification, unsuitable physical or operating environment, improper maintenance by  
you, or failure caused by a product for which IBM is not responsible. The warranty is voided by  
removal or alteration of Machine or parts identification labels.  
THESE WARRANTIES ARE YOUR EXCLUSIVE WARRANTIES AND  
REPLACE ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR  
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS  
FOR A PARTICULAR PURPOSE. THESE WARRANTIES GIVE YOU  
SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS  
WHICH VARY FROM JURISDICTION TO JURISDICTION. SOME  
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF  
EXPRESS OR IMPLIED WARRANTIES, SO THE ABOVE EXCLUSION OR  
LIMITATION MAY NOT APPLY TO YOU. IN THAT EVENT, SUCH  
WARRANTIES ARE LIMITED IN DURATION TO THE WARRANTY  
PERIOD. NO WARRANTIES APPLY AFTER THAT PERIOD.  
Items Not Covered by Warranty  
IBM does not warrant uninterrupted or error-free operation of a Machine. Unless specified  
otherwise, IBM provides non-IBM machines WITHOUT WARRANTIES OF ANY  
KIND.  
Any technical or other support provided for a Machine under warranty, such as assistance via  
telephone with “how-to” questions and those regarding Machine set-up and installation, will be  
provided WITHOUT WARRANTIES OF ANY KIND.  
5
Warranty Service  
To obtain warranty service for the Machine, contact your reseller or IBM. You may be required  
to present proof of purchase.  
IBM or your reseller provides certain types of repair and exchange service, either at your  
location or at a service center, to keep Machines in, or restore them to, conformance with their  
Specifications. IBM or your reseller will inform you of the available types of service for a  
Machine based on its country of installation. IBM may repair the failing Machine or exchange it  
at its discretion.  
When warranty service involves the exchange of a Machine or part, the item IBM or your  
reseller replaces becomes its property and the replacement becomes yours. You represent that all  
removed items are genuine and unaltered. The replacement may not be new, but will be in good  
working order and at least functionally equivalent to the item replaced. The replacement assumes  
the warranty service status of the replaced item.  
Any feature, conversion, or upgrade IBM or your reseller services must be installed on a  
Machine which is 1) for certain Machines, the designated, serial-numbered Machine and 2) at an  
engineering-change level compatible with the feature, conversion, or upgrade. Many features,  
conversions, or upgrades involve the removal of parts and their return to IBM. A part that  
replaces a removed part will assume the warranty service status of the removed part.  
Before IBM or your reseller exchanges a Machine or part, you agree to remove all features,  
parts, options, alterations, and attachments not under warranty service.  
You also agree to  
1. ensure that the Machine is free of any legal obligations or restrictions that prevent its  
exchange;  
2. obtain authorization from the owner to have IBM or your reseller service a Machine that  
you do not own; and  
3. where applicable, before service is provided  
a.  
follow the problem determination, problem analysis, and service request procedures  
that IBM or your reseller provides,  
b. secure all programs, data, and funds contained in a Machine,  
c.  
provide IBM or your reseller with sufficient, free, and safe access to your facilities to  
permit them to fulfil their obligations, and  
d. inform IBM or your reseller of changes in a Machine's location.  
IBM is responsible for loss of, or damage to, your Machine while it is 1) in IBM's possession or  
2) in transit in those cases where IBM is responsible for the transportation charges.  
Neither IBM nor your reseller is responsible for any of your confidential, proprietary or personal  
information contained in a Machine which you return to IBM or your reseller for any reason.  
You should remove all such information from the Machine prior to its return.  
Production Status  
Each IBM Machine is manufactured from new parts, or new and used parts. In some cases, the  
Machine may not be new and may have been previously installed. Regardless of the Machine's  
production status, IBM's appropriate warranty terms  
apply.  
Limitation of Liability  
Circumstances may arise where, because of a default on IBM's part or other liability, you are  
entitled to recover damages from IBM. In each such instance, regardless of the basis on which  
you are entitled to claim damages from IBM (including fundamental breach, negligence,  
misrepresentation, or other contract or tort claim), IBM is liable for no more than  
6
1. damages for bodily injury (including death) and damage to real property and tangible  
personal property; and  
2. the amount of any other actual direct damages, up to the greater of U.S. $100,000 (or  
equivalent in local currency) or the charges (if recurring, 12 months' charges apply) for the  
Machine that is the subject of the claim.  
This limit also applies to IBM's suppliers and your reseller. It is the maximum for which  
IBM, its suppliers, and your reseller are collectively responsible.  
UNDER NO CIRCUMSTANCES IS IBM LIABLE FOR ANY OF THE  
FOLLOWING: 1) THIRD-PARTY CLAIMS AGAINST YOU FOR  
DAMAGES (OTHER THAN THOSE UNDER THE FIRST ITEM LISTED  
ABOVE); 2) LOSS OF, OR DAMAGE TO, YOUR RECORDS OR DATA; OR  
3) SPECIAL, INCIDENTAL, OR INDIRECT DAMAGES OR FOR ANY  
ECONOMIC CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS  
OR SAVINGS), EVEN IF IBM, ITS SUPPLIERS OR YOUR RESELLER IS  
INFORMED OF THEIR POSSIBILITY. SOME JURISDICTIONS DO NOT  
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR  
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR  
EXCLUSION MAY NOT APPLY TO YOU.  
Part 2 - Worldwide Country-Unique Terms  
ASIA PACIFIC  
AUSTRALIA: The IBM Warranty for Machines: The following paragraph is added to this  
Section:  
The warranties specified in this Section are in addition to any rights you may have under the  
Trade Practices Act 1974 or other legislation and are only limited to the extent permitted by the  
applicable legislation.  
Extent of Warranty: The following replaces the first and second sentences of this Section:  
The warranty does not cover the repair or exchange of a Machine resulting from misuse,  
accident, modification, unsuitable physical or operating environment, operation in other than the  
Specified Operating Environment, improper maintenance by you, or failure caused by a product  
for which IBM is not responsible.  
Limitation of Liability: The following is added to this Section:  
Where IBM is in breach of a condition or warranty implied by the Trade Practices Act 1974,  
IBM's liability is limited to the repair or replacement of the goods or the supply of equivalent  
goods. Where that condition or warranty relates to right to sell, quiet possession or clear title, or  
the goods are of a kind ordinarily acquired for personal, domestic or household use or  
consumption, then none of the limitations in this paragraph apply.  
PEOPLE'S REPUBLIC OF CHINA: Governing Law: The following is added to this  
Statement:  
The laws of the State of New York govern this Statement.  
INDIA: Limitation of Liability: The following replaces items 1 and 2 of this Section:  
1. liability for bodily injury (including death) or damage to real property and tangible personal  
property will be limited to that caused by IBM's negligence;  
2. as to any other actual damage arising in any situation involving nonperformance by IBM  
pursuant to, or in any way related to the subject of this Statement of Warranty, IBM's liability  
7
will be limited to the charge paid by you for the individual Machine that is the subject of the  
claim.  
NEW ZEALAND: The IBM Warranty for Machines: The following paragraph is added to  
this Section:  
The warranties specified in this Section are in addition to any rights you may have under the  
Consumer Guarantees Act 1993 or other legislation which cannot be excluded or limited. The  
Consumer Guarantees Act 1993 will not apply in respect of any goods which IBM provides, if  
you require the goods for the purposes of a business as defined in that Act.  
Limitation of Liability: The following is added to this Section:  
Where Machines are not acquired for the purposes of a business as defined in the Consumer  
Guarantees Act 1993, the limitations in this Section are subject to the limitations in that Act.  
EUROPE, MIDDLE EAST, AFRICA (EMEA)  
The following terms apply to all EMEA countries.  
The terms of this Statement of Warranty apply to Machines purchased from an IBM reseller. If  
you purchased this Machine from IBM, the terms and conditions of the applicable IBM  
agreement prevail over this warranty statement.  
Warranty Service  
If you purchased an IBM Machine in Austria, Belgium, Denmark, Estonia, Finland, France,  
Germany, Greece, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Netherlands, Norway,  
Portugal, Spain, Sweden, Switzerland or United Kingdom, you may obtain warranty service for  
that Machine in any of those countries from either (1) an IBM reseller approved to perform  
warranty service or (2) from IBM.  
If you purchased an IBM Personal Computer Machine in Albania, Armenia, Belarus, Bosnia and  
Herzegovina, Bulgaria, Croatia, Czech Republic, Georgia, Hungary, Kazakhstan, Kirghizia,  
Federal Republic of Yugoslavia, Former Yugoslav Republic of Macedonia (FYROM), Moldova,  
Poland, Romania, Russia, Slovak Republic, Slovenia, or Ukraine, you may obtain warranty  
service for that Machine in any of those countries from either (1) an IBM reseller approved to  
perform warranty service or (2) from IBM.  
The applicable laws, Country-unique terms and competent court for this Statement are those of  
the country in which the warranty service is being provided. However, the laws of Austria  
govern this Statement if the warranty service is provided in Albania, Armenia, Belarus, Bosnia  
and Herzegovina, Bulgaria, Croatia, Czech Republic, Federal Republic of Yugoslavia, Georgia,  
Hungary, Kazakhstan, Kirghizia, Former Yugoslav Republic of Macedonia (FYROM), Moldova,  
Poland, Romania, Russia, Slovak Republic, Slovenia, and Ukraine.  
The following terms apply to the country specified:  
EGYPT: Limitation of Liability: The following replaces item 2 in this Section:  
2. as to any other actual direct damages, IBM's liability will be limited to the total amount you  
paid for the Machine that is the subject of the claim. Applicability of suppliers and resellers  
(unchanged).  
FRANCE: Limitation of Liability: The following replaces the second sentence of the first  
paragraph of this Section:  
In such instances, regardless of the basis on which you are entitled to claim damages from IBM,  
IBM is liable for no more than: (items 1 and 2 unchanged).  
GERMANY: The IBM Warranty for Machines: The following replaces the first sentence of  
the first paragraph of this Section:  
8
The warranty for an IBM Machine covers the functionality of the Machine for its normal use and  
the Machine's conformity to its Specifications.  
The following paragraphs are added to this Section:  
The minimum warranty period for Machines is six months.  
In case IBM or your reseller are unable to repair an IBM Machine, you can alternatively ask for a  
partial refund as far as justified by the reduced value of the unrepaired Machine or ask for a  
cancellation of the respective agreement for such  
Machine and get your money refunded.  
Extent of Warranty: The second paragraph does not apply.  
Warranty Service: The following is added to this Section:  
During the warranty period, transportation for delivery of the failing Machine to IBM will be at  
IBM's expense.  
Production Status: The following paragraph replaces this Section:  
Each Machine is newly manufactured. It may incorporate in addition to new parts,  
re-used parts as well.  
Limitation of Liability: The following is added to this Section:  
The limitations and exclusions specified in the Statement of Warranty will not apply to damages  
caused by IBM with fraud or gross negligence and for express warranty.  
In item 2, replace “U.S. $100,000” with “1.000.000 DEM.”  
The following sentence is added to the end of the first paragraph of item 2:  
IBM's liability under this item is limited to the violation of essential contractual terms in cases of  
ordinary negligence.  
IRELAND: Extent of Warranty: The following is added to this Section:  
Except as expressly provided in these terms and conditions, all statutory conditions, including all  
warranties implied, but without prejudice to the generality of the foregoing all warranties implied  
by the Sale of Goods Act 1893 or the Sale of Goods and Supply of Services Act 1980 are hereby  
excluded.  
Limitation of Liability: The following replaces items one and two of the first paragraph of this  
Section:  
1. death or personal injury or physical damage to your real property solely caused by IBM's  
negligence; and 2. the amount of any other actual direct damages, up to the greater of Irish  
Pounds 75,000 or 125 percent of the charges (if recurring, the 12 months' charges apply) for the  
Machine that is the subject of the claim or which otherwise gives rise to the claim.  
Applicability of suppliers and resellers (unchanged).  
The following paragraph is added at the end of this Section:  
IBM's entire liability and your sole remedy, whether in contract or in tort, in respect of any  
default shall be limited to damages.  
ITALY: Limitation of Liability: The following replaces the second sentence in the first  
paragraph:  
In each such instance unless otherwise provided by mandatory law, IBM is liable for no more  
than: (item 1 unchanged) 2)as to any other actual damage arising in all situations involving non-  
performance by IBM pursuant to, or in any way related to the subject matter of this Statement of  
Warranty, IBM's liability, will be limited to the total amount you paid for the Machine that is the  
subject of the claim.  
9
Applicability of suppliers and resellers (unchanged).  
The following replaces the second paragraph of this Section:  
Unless otherwise provided by mandatory law, IBM and your reseller are not liable for any of the  
following: (items 1 and 2 unchanged) 3) indirect damages, even if IBM or your reseller is  
informed of their possibility.  
SOUTH AFRICA, NAMIBIA, BOTSWANA, LESOTHO AND SWAZILAND: Limitation  
of Liability: The following is added to this Section:  
IBM's entire liability to you for actual damages arising in all situations involving  
nonperformance by IBM in respect of the subject matter of this Statement of Warranty will be  
limited to the charge paid by you for the individual Machine that is the subject of your claim  
from IBM.  
TURKIYE: Production Status: The following replaces this Section:  
IBM fulfils customer orders for IBM Machines as newly manufactured in accordance with IBM's  
production standards.  
UNITED KINGDOM: Limitation of Liability: The following replaces items 1 and 2 of the  
first paragraph of this Section:  
1. death or personal injury or physical damage to your real property solely caused by IBM's  
negligence;  
2. the amount of any other actual direct damages or loss, up to the greater of Pounds Sterling  
150,000 or 125 percent of the charges (if recurring, the 12 months' charges apply) for the  
Machine that is the subject of the claim or which otherwise gives rise to the claim.  
The following item is added to this paragraph:  
3. breach of IBM's obligations implied by Section 12 of the Sale of Goods Act 1979 or Section 2  
of the Supply of Goods and Services Act 1982.  
Applicability of suppliers and resellers (unchanged).  
The following is added to the end of this Section:  
IBM's entire liability and your sole remedy, whether in contract or in tort, in respect of any  
default will be limited to damages.  
NORTH AMERICA  
CANADA: Warranty Service: The following is added to this Section:  
To obtain warranty service from IBM, call 1-800-565-3344. In Toronto, call 416-383-3344.  
UNITED STATES OF AMERICA: Warranty Service: The following is added to this  
Section:  
To obtain warranty service from IBM, call 1-800-772-2227.  
10  
Compliances  
Before operating the monitor please read this manual thoroughly. This manual  
should be retained for future reference.  
FCC Class B Radio Frequency Interference Statement  
WARNING: (FOR FCC CERTIFIED MODELS)  
NOTE: This equipment has been tested and found to comply with the limits for  
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits  
are designed to provide reasonable protection against harmful interference in  
a residential installation. This equipment generates, uses and can radiate  
radio frequency energy, and if not installed and used in accordance with the  
instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off  
and on, the user is encouraged to try to correct the interference by one or  
more of the following measures:  
1. Reorient or relocate the receiving antenna.  
2. Increase the separation between the equipment and receiver.  
3. Connect the equipment into an outlet on a circuit different from that to  
which the receiver is connected.  
4. Consult the dealer or an experienced radio/TV technician for help.  
Notice :  
1. The changes or modifications not expressly approved by the party  
responsible for compliance could void the user's authority to operate the  
equipment.  
2. Shielded interface cables and AC power cord, if any, must be used in  
order to comply with the emission limits.  
3. The manufacturer is not responsible for any radio or TV interference  
caused by unauthorized modification to this equipment. It is the  
responsibilities of the user to correct such interference.  
Power Cords  
For your safety, IBM provides a power cord with a grounded  
attachment plug to use with this IBM product. To avoid electrical  
shock, always use the power cord and plug with a properly grounded  
power outlet.  
IBM power cords used in the United States and Canada are listed by  
the Underwriter’s Laboratories (UL) and certified by the Canadian  
Standards Association (CSA).  
11  
For units intended to be operated at 115 volts: Use a UL-listed and CSA-  
certified cord set consisting of a minimum 18 AWG, Type SVT or SJT,  
three-conductor cord, a maximum of 15 feet in length and a parallel blade,  
grounding-type attachment plug rated 15 amperes, 125 volts.  
For units intended to be operated at 230 volts (U.S. use): Use a UL-  
listed and CSA-certified cord set consisting of a minimum 18 AWG,  
type SVT or SJT, three-conductor cord, a maximum of 15 feet in  
length and a tandem blade, grounding-type attachment plug rated 15  
amperes, 250 volts.  
For units intended to be operated at 230 volts (outside the U.S.): Use  
a cord set with a grounding-type attachment plug. The cord set  
should have the appropriate safety approvals for the country in which  
the equipment will be installed.  
IBM power cords for a specific country or region are usually available  
only in that country or region.  
IBM fig. #  
IBM part  
number  
6952301  
Using countries  
(plug stnd.)  
4 (NEMA 5-  
15P) 125 V  
US, Canada, Mexico, Brazil, Costa  
Rica, Peru, Colombia, Ecuador,  
Venezuela, Bolivia, Panama, El  
Salvador, Honduras, Nicaragua,  
Dominican Republic, Guatemala,  
Taiwan, Saudi Arabia, Thailand,  
Philippines, Japan  
6 (AS/NZS  
c112)  
13F9939  
Austria, New Zealand  
18 (CEE 7 – vii) 13F9978  
France, Germany, Sweden, Norway,  
Austria, Netherlands, Finland,  
Belgium, Bosnia, Croatia, Egypt,  
Greece, Hungary, Poland, Portugal,  
Romania, Slovenia, Spain, Sweden,  
Turkey, Iceland, Estonia, Latvia,  
Lithuania, Luxembourg, Andorra,  
Guadeloupe, French Guyana,  
Martinique, Monaco, New Caledonia,  
Madagascar, Mauritius, Greece,  
Turkey, Portugal, Albania, Armenia,  
Azerbaijan, Belarus, Bosnia, Croatia,  
Czech Republic, Georgia, Hungary,  
Kazakhstan, Kyrhgistan, Macedonia,  
12  
Moldavia, Poland, Romania, Serbia,  
Slovakia, Slovenia, Tajikistan,  
Turkmenistan, Ukraine, Uzbekistan,  
Russia, Lebanon, Syria, Egypt, Iran,  
Algeria, Benin, Cape Verde, Burkina  
Faso, Cameroon, Central African  
Republic, Chad, Congo (Republic of),  
Congo (Democratic Republic of),  
Djibouti, Equatorial Guinea, Gabon,  
Guinea, Guinea Bissau, Ivory Coast,  
Mali, Mauritania, Morocco, Niger,  
Senegal, Togo, Tunisia, Angola,  
Burundi, Ethiopia, Mozambique,  
Rwanda, Somalia, Sao Tome, Eritrea,  
Mayotte, Comoros, Reunion, French  
Polynesia, Vanuatu, Wallis and  
Futuna, Korea, Vietnam, Indonesia  
UK, United Arab Emirate (Dubai)  
Hong Kong, Singapore, Malaysia,  
Ireland, Cyprus, Bahrain, Jordan,  
Kuwait, Oman, Qatar, Yemen,  
Gambia, Malta, Botswana,  
23 (BS 1363/A) 14F0032  
Seychelles, Nigeria, Ghana, Kenya,  
Liberia, Malawi, Sierra Leone, Sudan,  
Tanzania, Zambia, Zimbabwe  
Denmark  
19 (DK2-5a)  
13F9996  
25 (CEI 23-16) 14F0068  
2 (IRSM 2073) 36L8879  
62 (GB 2099.1) 02K0545  
Italy, Chile  
Argentina, Uruguay, Paraguay  
China  
32 (SI 32)  
14F0086  
Israel  
22 (SABS 164) 14F0014  
South Africa, India, Sri Lanka,  
Pakistan, Uganda, Lesotho, Namibia,  
Swaziland  
24 (1011-  
S24507)  
14F0050  
Switzerland, Lichtenstein  
Industry Canada Class B emission compliance statement  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B respecte toutes les exigences  
du Réglement sur le matériel brouilleur du Canada.  
13  
Avis de conformitéà la réglementation d'Industrie Canada  
Cet appareil numérique de classe B est conforme à la norme NMB-  
003 du Canada.  
As an ENERGY STAR Partner, IBM  
Corporation has determined that this product  
meets the ENERGY STAR guidelines for  
energy efficiency.  
MPRII  
This product complies with Swedish National Council for Metrology  
(MPR) standards issued in December 1999 (MPRII) for very low  
frequency (VLF) and Extremely low frequency (ELF) emissions.  
Hinweise  
Gemäß der Amtsblätter des BMPT Nm. 61Ú1991 und 6Ú1992 wird  
der Betreiber darauf aufmerksam gemächt, daß die von ihm mit  
diesem Gerät zusammengestellte Anlage auch den technischen  
Bestimmungen dieser Amtsblätter genügen muß.  
Aus ergonomischen Gründen wird empfohlen, die Grundfarbe Blau  
nicht auf dunklem Untergrund zu verwenden (schlechte  
Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast).  
Aus ergonomischen Gründen sollten nur Darstellungen auf dunklem  
Hintergrund bei Vertikalfrequenzen ab 60 Hz (ohne Zeilensprung)  
benutzt werden.  
Die Konvergenz des Bildes kann sich auf Grund des Magnetfeldes am  
Ort der Aufstellung aus der Korrekten Grundeinstellung verändern.  
Zur Korrektur empfiehlt es sich deshalb, die Regler an der Frontseite  
für H STAT und V STAT so einzustellen, daß die getrennt sichtbaren  
Farblinien für Rot. Grün und Blau bei z.B. der Darstellung eines  
Buchstabens zur Deckung (Konvergenz) gelangen. Siehe hierzu auch  
die Erklärungen zu H STAT und V STAT.  
14  
European Union (EU) Statement  
This product is in conformity with the protection requirements of the  
EU Council Directive 89/366/ECC on the approximation of the laws of  
the Member States relating to electromagnetic compatibility  
IBM can not accept responsibility for any failure to satisfy the  
protection requirements resulting from  
a
non-recommended  
modification of the product, including the fitting of non-IBM option  
cards.  
This product has been tested and found to comply with the limits for  
Class B Information Technology Equipment according to CISPR 22  
Ú European Standard EN 55022. The limits for Class B equipment  
were derived for typical residential environments to provide  
reasonable  
protection  
against  
interference  
with  
licensed  
communication devices.  
Properly shielded and grounded cables and connectors must be used in  
order to reduce the potential for causing interference to radio and TV  
communications and to other electrical or electronic equipment. Such  
cables and connectors are available from IBM authorised dealers.  
In accordance with EN 50082-1 1992, Performance Criterion A:, it  
should be noted that in the presence of certain electromagnetic fields,  
some screen jitter may be observed.  
Spécifications de la CEE  
Ce produit est conforme aux exigences de protection de la directive  
89/ 336/ EEC du Conseil de l’UE sur le rapprochement des lois des  
États membres en matière de compatibilité électromagnétique.  
IBM ne peut accepter aucune responsabilité pour le manquement aux  
exi gences de protection résultant d’une modification non  
recommandée du produit, y compris l’installation de cartes autres que  
les cartes IBM.  
Ce produit a été testé et il satisfait les conditions de l’équipement  
informatique de Classe B en vertu de CISPR22 / Standard européen  
EN 55022. Les conditions pour l’équipement de Classe B ont été  
définies en fonction d’un contexte résidentiel ordinaire afin de fournir  
15  
une protection raisonnable contre l’interférence d’appareils de  
communication autorisés.  
Des câbles blindés et correctment reliés à la terre doivent être utilisés  
pour réduire les risques d’interférence avec des communications radio  
et télévisées, ainsi qu’avec des équipements électriques ou  
électroniques. Ces câbles et connecteurs sont disponibles auprés de  
vos revendeurs IBM agréés.  
Conformément à la norme EN 50082- 1 1992 (Critére de Performance  
A), l’utilisateur doit être conscient du fait qu’en présence de certains  
champs électroma gnétiques, l’image peut être instable.  
Erklärung für die Europäische Union (EU)  
Dieses Produkt worde getestet, und dabei wurde festgestellt, daß es  
gemäß CISPR-2 Ú Europäische Norm EN 55022 die Grenzwerte für  
Ausrüstung der Informationstechnik, Klasse B, einhält. Die  
Grenzwerte für Ausrüstung der Klasse B wurden für eine typische  
Wohnumgebung erarbeitet, um einen angemessenen Schutz vor  
Störungen im Zusammenhang mit zugelassenen Kommunikations-  
geräten zu gewährleisten.  
Es sind ordnungsgemäß abgeschirmte und geerdete Kabel und  
Stecker zu verwenden, um das Störungspotential in bezug auf Radio-  
und Fernsehempfang oder andere elektrische oder elekronische  
Geräte zu reduzieren. Solche Kabel und Stecker sind bei autorisierten  
IBM- Fachhändlern erhältlich.  
In Übereinstimmung mit EN 50082-1 1992, Leistungskriterium A wird  
darauf hingewiesen, daß bestimmte elektromagnetische Felder ein  
Flattern auf dem Bildschirm hervorrufen können.  
Declaración de la Unión Europea (UE)  
Este producto satisface los requisitos de protección del Consejo de la  
UE, Directiva 89/ 336/ CEE en lo que a la le gislatura de los Estados  
Miembros sobre compatibilidad electroma gnética se refiere.  
IBM no puede aceptar responsabilidad al guna si este producto deja  
de satisfacer dichos requisitos de protección como resultado de una  
modificación no recomendada del producto, inclu yendo el ajuste de  
tarjetas de opción que no sean IBM.  
16  
Este producto ha sido probado y satisface los límites para Equipos  
Informáticos Clase B de conformidad con el Estándar CISPR22 y el  
Estándar Europeo EN 55022. Los límites para los equipos de Clase B  
se han establecido para entornos residenciales típicos a fin de  
proporcionar una protección razonable contra las interferencias con  
dispositivos de comunicación licenciados.  
Se deben utilizar concetores y cables debidamente protegidos y  
conectados a tierra a fin de reducir las posibilidades de que se  
produzcan interferencias con comunicaciones por radio o televisión y  
otros equipos eléctricos o electrónicos. Este tipo de cables y  
conectores pueden adquirirse en concesionarios autorizados de IBM.  
De acuerdo con la norma EN 50082- 1 1992, Performance Criterion  
A, habría que destacar que en presencia de determinados campos  
electroma gnéticos, podría observarse una marcada inestabilidad e la  
imagen.  
17  
Dichiarazione di conformità dell’Unione Europea (EU)  
Questo prodotto è conforme alle normative di protezione ai sensi della  
Direttiva del Consi glio dell’Unione Europea 89/ 336/ CEE  
sull’armonizzazione le gislativa degli stati membri in materia di  
compatibilità elettromagnetica.  
IBM non accetta responsabilità alcuna per la mancata conformità alle  
normative di protezione dovuta a modifiche non consi gliate al  
prodotto, compresa l’installazione di schede e componenti di marca  
diversa da IBM.  
Le prove effettuate sul presente prodotto hanno accertato che esso  
rientra nei limiti stabiliti per le le apparecchiature di informatica Classe  
B ai sensi del CISPR 22 / Norma Europea EN 55022. I limiti delle  
apparecchiature della Classe B sono stati stabiliti al fine di fornire ra  
gionevole protezione da interferenze mediante dispositivi di  
comunicazione in concessione in ambienti residenziali tipici.  
Utilizzare cavi e connettori colle gati a terra per ridurre il rischio  
potenziale di interferenza delle comunicazioni radiotelevisive e di a; tri  
apparecchi elettrici o elettronici. I cavi sono disponibili presso i  
rivenditori IBM.  
In accordo con quando previsto nel documento EN 50082- 1 1992,  
Performance Criterion A, é importante sottolineare che in presenza di  
determinati campi elettroma gnetici é possibile che si verifichi un certo  
tremolio delle immagini.  
Europeiska unionen (EU)  
Denna produkt har testats och följer gränsvärdena för Klass B  
Information Technology Equipment enligt CISPR 22 Ú Europeisk  
standard EN 55022. Gränsvärden för Klass B-utrutning utgår frår  
vanliga bostadsomräden för att ge ett rimligt skydd mot störningar i  
kommunikationsenheter.  
Korrekt avskärmade och jordade kablar och kontakter måste  
användas för att minska risken för störningar i radio- och TV-  
kommunikationer och annan elektrisk utrustning. Sådana kablar och  
kontakter finns tillgängliga hos auktoriserade IBM-återförsäljare.  
18  
I enlighet med EN 50082-1 1992, Performance Criterion A påpekas  
följande: I närheten av en del elektromagnetiska fält kan vissa  
bildstörningar uppstår på skårmen.  
Deutsche EMV-Direktive  
(electromagnetische Verträglichkeit)  
Dieses Gerät ist berechtigt in Übereinstimmung mit dem deutschen  
EMVG vom 9.Nov.92 das EG-Konformitätszeichen zu führen.  
Der Aussteller der Konformitätserklärung ist die IBM UK, Greenock.  
Dieses Gerät erfüllt die Bedingungen der EN 55022 Klasse B.  
19  
Service Information  
The following parts are for use by IBM service, or IBM authorized dealers, to  
support customer warranty. Parts are for service use only.  
Model Type 2248  
Part Number  
M/T-Model  
Description  
22P4585  
2248-0CN  
Monitor-UVNH  
(pearl white)  
06P3799  
22P4778  
2248-0CE  
Monitor-UVEQ  
(pearl white)  
2248-0CN  
2248-0CE  
Tilt/Swivel Base  
(pearl white)  
20  

JVC AV 32430 User Manual
LG Electronics LG Life Good Computer Monitor M2280DN User Manual
Miele KM 320 User Manual
NEC DPSB70 User Manual
Omega Engineering OME A8111 User Manual
Panasonic DIGA DMR ES40V User Manual
Panasonic Proprietary Telephones KX T7750 User Manual
Philips 109B2x User Manual
Philips 150B6CB User Manual
Philips 300WN5DB User Manual