Lenovo 3000 N500
Hardware Maintenance Manual
Lenovo 3000 N500
Hardware Maintenance Manual
Note
Before using this information and the product it supports, be sure to read the general information under “Notices” on page
First Edition (October 2008)
© Copyright Lenovo 2008. All rights reserved.
LENOVO products, data, computer software, and services have been developed exclusively at private expense and
are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted
rights to use, reproduction and disclosure.
LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or services are delivered
pursuant a General Services Administration ″GSA″ contract, use, reproduction, or disclosure is subject to restrictions
set forth in Contract No. GS-35F-05925.
© 2008 Lenovo
Contents
© Copyright Lenovo 2008
iii
iv Lenovo 3000 N500 Hardware Maintenance Manual
About this manual
This manual contains service and reference information for the following Lenovo
3000 products.
Lenovo 3000 N500
MT 4233
Use this manual along with the advanced diagnostic tests to troubleshoot
problems.
The manual is divided into sections as follows:
v The common sections provide general information, guidelines, and safety
information required in servicing computers.
v The product-specific section includes service, reference, and product-specific
parts information.
Important:
This manual is intended only for trained servicers who are familiar with Lenovo
3000 products. Use this manual along with the advanced diagnostic tests to
troubleshoot problems effectively.
Before servicing a Lenovo 3000 product, be sure to read all the information
© Copyright Lenovo 2008
v
vi Lenovo 3000 N500 Hardware Maintenance Manual
General safety
Follow these rules to ensure general safety:
v Observe good housekeeping in the area of the machines during and after
maintenance.
v When lifting any heavy object:
1. Make sure that you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to
lift.
4. Lift by standing or by pushing up with your leg muscles; this action removes
the strain from the muscles in your back. Do not attempt to lift any object that
weighs more than 16 kg (35 lb) or that you think is too heavy for you.
v Do not perform any action that causes hazards to the customer, or that makes
the equipment unsafe.
v Before you start the machine, make sure that other service representatives and
the customer’s personnel are not in a hazardous position.
v Place removed covers and other parts in a safe place, away from all personnel,
while you are servicing the machine.
v Keep your toolcase away from walk areas so that other people will not trip over
it.
v Do not wear loose clothing that can be trapped in the moving parts of a
machine. Make sure that your sleeves are fastened or rolled up above your
elbows. If your hair is long, fasten it.
v Insert the ends of your necktie or scarf inside clothing or fasten it with a
nonconductive clip, about 8 centimeters (3 inches) from the end.
v Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your
clothing.
Attention: Metal objects are good electrical conductors.
v Wear safety glasses when you are hammering, drilling, soldering, cutting wire,
attaching springs, using solvents, or working in any other conditions that might
be hazardous to your eyes.
v After service, reinstall all safety shields, guards, labels, and ground wires.
Replace any safety device that is worn or defective.
v Reinstall all covers correctly before returning the machine to the customer.
v Fan louvers on the machine help to prevent overheating of internal components.
Do not obstruct fan louvers or cover them with labels or stickers.
2
Lenovo 3000 N500 Hardware Maintenance Manual
Electrical safety
Observe the following rules when working on electrical equipment.
Important:
Use only approved tools and test equipment. Some hand tools have handles
covered with a soft material that does not insulate you when working with live
electrical currents.
Many customers have, near their equipment, rubber floor mats that contain small
conductive fibers to decrease electrostatic discharges. Do not use this type of mat
to protect yourself from electrical shock.
v Find the room emergency power-off (EPO) switch, disconnecting switch, or
electrical outlet. If an electrical accident occurs, you can then operate the switch
or unplug the power cord quickly.
v Do not work alone under hazardous conditions or near equipment that has
hazardous voltages.
v Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
v Before you start to work on the machine, unplug the power cord. If you cannot
unplug it, ask the customer to power-off the wall box that supplies power to the
machine, and to lock the wall box in the off position.
v If you need to work on a machine that has exposed electrical circuits, observe the
following precautions:
– Ensure that another person, familiar with the power-off controls, is near you.
Attention: Another person must be there to switch off the power, if
necessary.
– Use only one hand when working with powered-on electrical equipment;
keep the other hand in your pocket or behind your back.
Attention: An electrical shock can occur only when there is a complete
circuit. By observing the above rule, you may prevent a current from passing
through your body.
– When using testers, set the controls correctly and use the approved probe
leads and accessories for that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you
from grounds such as metal floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages;
Instructions for these precautions are in the safety sections of maintenance
information. Use extreme care when measuring high voltages.
v Regularly inspect and maintain your electrical hand tools for safe operational
condition.
v Do not use worn or broken tools and testers.
v Never assume that power has been disconnected from a circuit. First, check that it
has been powered off.
v Always look carefully for possible hazards in your work area. Examples of these
hazards are moist floors, nongrounded power extension cables, power surges,
and missing safety grounds.
Safety information
3
v Do not touch live electrical circuits with the reflective surface of a plastic dental
mirror. The surface is conductive; such touching can cause personal injury and
machine damage.
v Do not service the following parts with the power on when they are removed
from their normal operating places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
and similar units. (This practice ensures correct grounding of the units.)
v If an electrical accident occurs:
– Use caution; do not become a victim yourself.
– Switch off power.
– Send another person to get medical aid.
4
Lenovo 3000 N500 Hardware Maintenance Manual
Safety inspection guide
The purpose of this inspection guide is to assist you in identifying potentially
unsafe conditions. As each machine was designed and built, required safety items
were installed to protect users and service personnel from injury. This guide
addresses only those items. You should use good judgment to identify potential
safety hazards due to attachment of non-Lenovo 3000 features or options not
covered by this inspection guide.
If any unsafe conditions are present, you must determine how serious the apparent
hazard could be and whether you can continue without first correcting the
problem.
Consider these conditions and the safety hazards they present:
v Electrical hazards, especially primary power (primary voltage on the frame can
cause serious or fatal electrical shock)
v Explosive hazards, such as a damaged CRT face or a bulging capacitor
v Mechanical hazards, such as loose or missing hardware
To determine whether there are any potentially unsafe conditions, use the
following checklist at the beginning of every service task. Begin the checks with
the power off, and the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Power off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to measure
third-wire ground continuity for 0.1 ohm or less between the external
ground pin and the frame ground.
b. The power cord should be the type specified in the parts list.
c. Insulation must not be frayed or worn.
4. Check for cracked or bulging batteries.
5. Remove the cover.
6. Check for any obvious non-Lenovo 3000 alterations. Use good judgment as to
the safety of any non-Lenovo 3000 alterations.
7. Check inside the unit for any obvious unsafe conditions, such as metal filings,
contamination, water or other liquids, or signs of fire or smoke damage.
8. Check for worn, frayed, or pinched cables.
9. Check that the power-supply cover fasteners (screws or rivets) have not been
removed or tampered with.
Safety information
5
Handling devices that are sensitive to electrostatic discharge
Any computer part containing transistors or integrated circuits (ICs) should be
considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when
there is a difference in charge between objects. Protect against ESD damage by
equalizing the charge so that the machine, the part, the work mat, and the person
handling the part are all at the same charge.
Notes:
1. Use product-specific ESD procedures when they exceed the requirements
noted here.
2. Make sure that the ESD protective devices you use have been certified (ISO
9000) as fully effective.
When handling ESD-sensitive parts:
v Keep the parts in protective packages until they are inserted into the product.
v Avoid contact with other people.
v Wear a grounded wrist strap against your skin to eliminate static on your body.
v Prevent the part from touching your clothing. Most clothing is insulative and
retains a charge even when you are wearing a wrist strap.
v Use the black side of a grounded work mat to provide a static-free work surface.
The mat is especially useful when handling ESD-sensitive devices.
v Select a grounding system, such as those listed below, to provide protection that
meets the specific service requirement.
Note:
The use of a grounding system to guard against ESD damage is desirable but not
necessary.
– Attach the ESD ground clip to any frame ground, ground braid, or green-wire
ground.
– When working on a double-insulated or battery-operated system, use an ESD
common ground or reference point. You can use coax or connector-outside
shells on these systems.
– Use the round ground prong of the ac plug on ac-operated computers.
Grounding requirements
Electrical grounding of the computer is required for operator safety and correct
system function. Proper grounding of the electrical outlet can be verified by a
certified electrician.
6
Lenovo 3000 N500 Hardware Maintenance Manual
Safety notices: multilingual translations
The safety notices in this section are provided in English, French, German, Hebrew,
Italian, Japanese, and Spanish.
Safety notice 1
Before the computer is powered on after FRU replacement, make sure all screws,
springs, and other small parts are in place and are not left loose inside the
computer. Verify this by shaking the computer and listening for rattling sounds.
Metallic parts or metal flakes can cause electrical shorts.
Avant de remettre l’ordinateur sous tension après remplacement d’une unité en
clientèle, vérifiez que tous les ressorts, vis et autres pièces sont bien en place et
bien fixées. Pour ce faire, secouez l’unité et assurez-vous qu’aucun bruit suspect
ne se produit. Des pièces métalliques ou des copeaux de métal pourraient causer
un court-circuit.
Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird,
muß sichergestellt werden, daß keine Schrauben, Federn oder andere Kleinteile
fehlen oder im Gehäuse vergessen wurden. Der Computer muß geschüttelt und
auf Klappergeräusche geprüft werden. Metallteile oder-splitter können
Kurzschlüsse erzeugen.
Prima di accendere l’elaboratore dopo che é stata effettuata la sostituzione di una FRU,
accertarsi che tutte le viti, le molle e tutte le altri parti di piccole dimensioni siano nella
corretta posizione e non siano sparse all’interno dell’elaboratore. Verificare ciò scuotendo
l’elaboratore e prestando attenzione ad eventuali rumori; eventuali parti o pezzetti
metallici possono provocare cortocircuiti pericolosi.
Antes de encender el sistema despues de sustituir una FRU, compruebe que todos los
tornillos, muelles y demás piezas pequeñas se encuentran en su sitio y no se encuentran
sueltas dentro del sistema. Compruébelo agitando el sistema y escuchando los posibles
ruidos que provocarían. Las piezas metálicas pueden causar cortocircuitos eléctricos.
Safety information
7
Safety notice 2
DANGER
Some standby batteries contain a small amount of nickel and cadmium. Do not
disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it.
Dispose of the battery as required by local ordinances or regulations. Use only the
battery in the appropriate parts listing. Use of an incorrect battery can result in
ignition or explosion of the battery.
Certaines batteries de secours contiennent du nickel et du cadmium. Ne les démontez
pas, ne les rechargez pas, ne les exposez ni au feu ni à l’eau. Ne les mettez pas en
court-circuit. Pour les mettre au rebut, conformez-vous à la réglementation en vigueur.
Lorsque vous remplacez la pile de sauvegarde ou celle de l’horloge temps réel, veillez
à n’utiliser que les modèles cités dans la liste de pièces détachées adéquate. Une
batterie ou une pile inappropriée risque de prendre feu ou d’exploser.
Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet, kann
geringe Mengen Nickel und Cadmium enthalten. Sie darf nur durch die Verkaufsstelle
oder den IBM Kundendienst ausgetauscht werden. Sie darf nicht zerlegt,
wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Die
Batterie kann schwere Verbrennungen oder Verätzungen verursachen. Bei der
Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim Ersetzen der
Bereitschafts-oder Systembatterie nur Batterien des Typs verwenden, der in der
Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann zu Entzündung oder
Explosion führen.
Alcune batterie di riserva contengono una piccola quantità di nichel e cadmio. Non
smontarle, ricaricarle, gettarle nel fuoco o nell’acqua né cortocircuitarle. Smaltirle
secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni
locali). Quando si sostituisce la batteria dell’RTC (real time clock) o la batteria di
supporto, utilizzare soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego di
una batteria non adatta potrebbe determinare l’incendio o l’esplosione della batteria
stessa.
Algunas baterías de reserva contienen una pequeña cantidad de níquel y cadmio. No
las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite.
Deséchelas tal como dispone la normativa local. Utilice sólo baterías que se
encuentren en la lista de piezas. La utilización de una batería no apropiada puede
provocar la ignición o explosión de la misma.
8
Lenovo 3000 N500 Hardware Maintenance Manual
Safety notice 3
DANGER
The battery pack contains small amounts of nickel. Do not disassemble it, throw it
into fire or water, or short-circuit it. Dispose of the battery pack as required by local
ordinances or regulations. Use only the battery in the appropriate parts listing when
replacing the battery pack. Use of an incorrect battery can result in ignition or
explosion of the battery.
La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau.
Ne la mettez pas en court-circuit. Pour la mettre au rebut, conformez-vous à la
réglementation en vigueur. Lorsque vous remplacez la batterie, veillez à n’utiliser que
les modèles cités dans la liste de pièces détachées adéquate. En effet, une batterie
inappropriée risque de prendre feu ou d’exploser.
Akkus enthalten geringe Mengen von Nickel. Sie dürfen nicht zerlegt,
wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Bei
der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim Ersetzen
der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgeführt ist.
Der Einsatz falscher Batterien kann zu Entzündung oder Explosion führen.
La batteria contiene piccole quantità di nichel. Non smontarla, gettarla nel fuoco o
nell’acqua né cortocircuitarla. Smaltirla secondo la normativa in vigore (DPR 915/82,
successive disposizioni e disposizioni locali). Quando si sostituisce la batteria,
utilizzare soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego di una
batteria non adatta potrebbe determinare l’incendio o l’esplosione della batteria stessa.
Las baterías contienen pequeñas cantidades de níquel. No las desmonte, ni recargue,
ni las eche al fuego o al agua ni las cortocircuite. Deséchelas tal como dispone la
normativa local. Utilice sólo baterías que se encuentren en la lista de piezas al
sustituir la batería. La utilización de una batería no apropiada puede provocar la
ignición o explosión de la misma.
Safety information
9
Safety notice 4
DANGER
The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it,
remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate
it, or expose its cell contents to water. Dispose of the battery as required by local
ordinances or regulations. Use only the battery in the appropriate parts listing. Use of
an incorrect battery can result in ignition or explosion of the battery.
La pile de sauvegarde contient du lithium. Elle présente des risques d’incendie,
d’explosion ou de brûlures graves. Ne la rechargez pas, ne retirez pas son connecteur
polarisé et ne la démontez pas. Ne l’exposez pas à une temperature supérieure à 100°C,
ne la faites pas brûler et n’en exposez pas le contenu à l’eau. Mettez la pile au rebut
conformément à la réglementation en vigueur. Une pile inappropriée risque de
prendre feu ou d’exploser.
Die Systembatterie ist eine Lithiumbatterie. Sie kann sich entzünden, explodieren
oder schwere Verbrennungen hervorrufen. Batterien dieses Typs dürfen nicht
aufgeladen, zerlegt, über 100 C erhitzt oder verbrannt werden. Auch darf ihr Inhalt
nicht mit Wasser in Verbindung gebracht oder der zur richtigen Polung angebrachte
Verbindungsstecker entfernt werden. Bei der Entsorgung die örtlichen Bestimmungen
für Sondermüll beachten. Beim Ersetzen der Batterie nur Batterien des Typs
verwenden, der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien
kann zu Entzündung oder Explosion führen.
La batteria di supporto e una batteria al litio e puo incendiarsi, esplodere o procurare
gravi ustioni. Evitare di ricaricarla, smontarne il connettore polarizzato, smontarla,
riscaldarla ad una temperatura superiore ai 100 gradi centigradi, incendiarla o gettarla
in acqua. Smaltirla secondo la normativa in vigore (DPR 915/82, successive
disposizioni e disposizioni locali). L’impiego di una batteria non adatta potrebbe
determinare l’incendio o l’esplosione della batteria stessa.
La batería de repuesto es una batería de litio y puede provocar incendios, explosiones
o quemaduras graves. No la recargue, ni quite el conector polarizado, ni la desmonte,
ni caliente por encima de los 100°C (212°F), ni la incinere ni exponga el contenido de
sus celdas al agua. Deséchela tal como dispone la normativa local.
10 Lenovo 3000 N500 Hardware Maintenance Manual
Safety notice 5
If the LCD breaks and the fluid from inside the LCD gets into your eyes or on
your hands, immediately wash the affected areas with water for at least 15
minutes. Seek medical care if any symptoms from the fluid are present after
washing.
Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les
yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au
moins quinze minutes. Consultez un médecin si des symptômes persistent après
le lavage.
Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der Entsorgung
die örtlichen Bestimmungen für Sondermüll beachten. Der LCD-Bildschirm
besteht aus Glas und kann zerbrechen, wenn er unsachgemäß behandelt wird
oder der Computer auf den Boden fällt. Wenn der Bildschirm beschädigt ist und
die darin befindliche Flüssigkeit in Kontakt mit Haut und Augen gerät, sollten
die betroffenen Stellen mindestens 15 Minuten mit Wasser abgespült und bei
Beschwerden anschließend ein Arzt aufgesucht werden.
Nel caso che caso l’LCD si dovesse rompere ed il liquido in esso contenuto entrasse in
contatto con gli occhi o le mani, lavare immediatamente le parti interessate con acqua
corrente per almeno 15 minuti; poi consultare un medico se i sintomi dovessero
permanere.
Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos o sus manos,
lave inmediatamente las áreas afectadas con agua durante 15 minutos como mínimo.
Obtenga atención medica si se presenta algún síntoma del fluido despues de lavarse.
Safety information 11
Safety notice 6
DANGER
To avoid shock, do not remove the plastic cover that protects the lower part of the
inverter card.
Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique
protégeant la partie inférieure de la carte d’alimentation.
Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der
Spannungswandlerplatine umgibt, nicht entfernen.
Per evitare scosse elettriche, non rimuovere la copertura in plastica che avvolge la
parte inferiore della scheda invertitore.
Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja de la
tarjeta invertida.
Safety notice 7
DANGER
Though the main batteries have low voltage, a shorted or grounded battery can
produce enough current to burn personnel or combustible materials.
Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la mise
à la masse d’une batterie peut produire suffisamment de courant pour brûler des
matériaux combustibles ou causer des brûlures corporelles graves.
Obwohl Hauptbatterien eine niedrige Spannung haben, können sie doch bei
Kurzschluß oder Erdung genug Strom abgeben, um brennbare Materialien zu
entzünden oder Verletzungen bei Personen hervorzurufen.
Sebbene le batterie di alimentazione siano a basso voltaggio, una batteria in corto
circuito o a massa può fornire corrente sufficiente da bruciare materiali combustibili o
provocare ustioni ai tecnici di manutenzione.
Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada o
con contacto a tierra puede producir la corriente suficiente como para quemar material
combustible o provocar quemaduras en el personal.
12 Lenovo 3000 N500 Hardware Maintenance Manual
Safety notice 8
DANGER
Before removing any FRU, power off the computer, unplug all power cords from
electrical outlets, remove the battery pack, and then disconnect any interconnecting
cables.
Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension,
débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la
batterie et déconnectez tous les cordons d’interface.
Die Stromzufuhr muß abgeschaltet, alle Stromkabel aus der Steckdose gezogen, der
Akku entfernt und alle Verbindungskabel abgenommen sein, bevor eine FRU entfernt
wird.
Prima di rimuovere qualsiasi FRU, spegnere il sistema, scollegare dalle prese elettriche
tutti i cavi di alimentazione, rimuovere la batteria e poi scollegare i cavi di
interconnessione.
Antes de quitar una FRU, apague el sistema, desenchufe todos los cables de las tomas
de corriente eléctrica, quite la batería y, a continuación, desconecte cualquier cable de
conexión entre dispositivos.
Safety information 13
Laser compliance statement
Some models of Lenovo 3000 computer are equipped from the factory with an
optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such
devices are also sold separately as options. If one of these drives is installed, it is
certified in the U.S. to conform to the requirements of the Department of Health
and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J
for Class 1 laser products. Elsewhere, the drive is certified to conform to the
requirements of the International Electrotechnical Commission (IEC) 825 and
CENELEC EN 60 825 for Class 1 laser products.
If a CD-ROM drive, a DVD-ROM drive, or another laser device is installed, note
the following:
CAUTION:
Use of controls or adjustments or performance of procedures other than those
specified herein might result in hazardous radiation exposure.
O uso de controles, ajustes ou desempenho de procedimentos diferentes daqueles aqui
especificados pode resultar em perigosa exposição à radiação.
Pour éviter tout risque d’exposition au rayon laser, respectez les consignes de réglage
et d’utilisation des commandes, ainsi que les procédures décrites.
Werden Steuer- und Einstellelemente anders als hier festgesetzt verwendet, kann
gefährliche Laserstrahlung auftreten.
L’utilizzo di controlli, regolazioni o l’esecuzione di procedure diverse da quelle
specificate possono provocare l’esposizione a.
El uso de controles o ajustes o la ejecución de procedimientos distintos de los aquí
especificados puede provocar la exposición a radiaciones peligrosas.
Opening the CD-ROM drive, the DVD-ROM drive, or any other optical storage
device could result in exposure to hazardous laser radiation. There are no
serviceable parts inside those drives. Do not open.
14 Lenovo 3000 N500 Hardware Maintenance Manual
A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may
contain an embedded Class 3A or Class 3B laser diode. Note the following:
DANGER
Emits visible and invisible laser radiation when open. Do not stare into the beam, do
not view directly with optical instruments, and avoid direct exposure to the beam.
Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe diretamente
por meio de instrumentos óticos e evite exposição direta com o feixe de luz.
Rayonnement laser si carter ouvert. Évitez de fixer le faisceau, de le regarder
directement avec des instruments optiques, ou de vous exposer au rayon.
Laserstrahlung bei geöffnetem Gerät. Nicht direkt oder über optische Instrumente in
den Laserstrahl sehen und den Strahlungsbereich meiden.
Kinyitáskor lézersugár ! Ne nézzen bele se szabad szemmel, se optikai eszközökkel.
Kerülje a sugárnyalábbal való érintkezést !.
Aprendo l’unità vengono emesse radiazioni laser. Non fissare il fascio, non guardarlo
direttamente con strumenti ottici e evitare l’esposizione diretta al fascio.
Radiación láser al abrir. No mire fijamente ni examine con instrumental óptico el haz
de luz. Evite la exposición directa al haz.
Safety information 15
16 Lenovo 3000 N500 Hardware Maintenance Manual
Important service information
This chapter presents following important service information:
Important:
BIOS and device driver fixes are customer-installable. The BIOS and device
drivers are posted on the customer support site http://www.lenovo.com/support
System Disassembly/Reassembly videos that show the FRU removals or
replacements for the Lenovo® authorized service technicians are available in the
following support site: http://www.lenovoservicetraining.com/ion/
Advise customers to contact the Customer Support Center at 800-426-7378 if they
need assistance in obtaining or installing any software fixes, drivers, and BIOS
downloads.
Customers in Canada should call the Customer Support Center at 800-565-3344
for assistance or download information.
Strategy for replacing FRUs
Before replacing parts:
Make sure that all software fixes, drivers, and BIOS downloads are installed
before replacing any FRUs listed in this manual.
After a system board is replaced, ensure that the latest BIOS is loaded to the
system board before completing the service action.
To download software fixes, drivers, and BIOS, do as follows:
2. Enter the product number of the computer or press Auto-detect button on the
screen.
3. Select Downloads and drivers.
4. Follow the directions on the screen and install the necessary software.
Use the following strategy to prevent unnecessary expense for replacing and
servicing FRUs:
© Copyright Lenovo 2008
17
v If you are instructed to replace a FRU but the replacement does not correct the
problem, reinstall the original FRU before you continue.
v Some computers have both a processor board and a system board. If you are
instructed to replace either the processor board or the system board, and
replacing one of them does not correct the problem, reinstall that board, and
then replace the other one.
v If an adapter or a device consists of more than one FRU, any of the FRUs may
be the cause of the error. Before replacing the adapter or device, remove the
FRUs, one by one, to see if the symptoms change. Replace only the FRU that
changed the symptoms.
Attention: The setup configuration on the computer you are servicing may have
been customized. Running Automatic Configuration may alter the settings. Note
the current configuration settings (using the View Configuration option); then,
when service has been completed, verify that those settings remain in effect.
Strategy for replacing a hard disk drive
Always try to run a low-level format before replacing a hard disk drive. This will
cause all customer data on the hard disk to be lost. Be sure that the customer has a
current backup of the data before doing this task.
Attention: The drive startup sequence in the computer you are servicing may
have been changed. Be extremely careful during write operations such as copying,
saving, or formatting. If you select an incorrect drive, data or programs can be
overwritten.
Important notice for replacing a system board
Some components mounted on a system board are very sensitive. Improper
handling of a system board can cause damage to those components, and may
cause a system malfunction.
Attention: When handling a system board:
v Do not drop a system board or apply any excessive force to it.
v Avoid rough handling of any kind.
v Avoid bending a system board and hard pushing to prevent cracking at each
BGA (Ball Grid Array) chipset.
How to use error message
Use the error codes displayed on the screen to diagnose failures. If more than one
error code is displayed, begin the diagnosis with the first error code. Whatever
causes the first error code may also cause false error codes. If no error code is
displayed, see whether the error symptom is listed in the Symptom-to-FRU Index
for the computer you are servicing.
18 Lenovo 3000 N500 Hardware Maintenance Manual
Strategy for replacing FRUs for CTO, CMV, and GAV
Product definition
Dynamic Configure To Order (CTO)
This provides the ability for a customer to configure an IBM® or a Lenovo solution
from an eSite, and have this configuration sent to fulfillment, where it is built and
shipped directly to the customer. The machine label, Product Entitlement
Warehouse (PEW), eSupport, and the HMM will load these products as the 4-digit
MT and 3-digit model, where model = “CTO” (Example: 1829-CTO).
Custom Model Variant (CMV)
This is a unique configuration that has been negotiated between IBM or Lenovo
and the customer. A unique 4-digit MT and 3-digit model is provided to the
customer to place orders (Example: 1829-W15). A CMV is a special bid offering.
Therefore, it is NOT generally announced.
v The MTM portion of the machine label is the 4-digit MT and 3-digit model,
where model = “CTO” (Example: 1829-CTO). The PRODUCT ID portion of the
machine label is the 4-digit MT and 3-digit CMV model (Example: 1829-W15).
v The PEW record is the 4-digit MT and 3-digit model, where model = “CTO”
(Example: 1829-CTO).
v eSupport will show both the CTO and CMV machine type models (Example:
1829-CTO and 1829-W15 will be found on the eSupport site.)
v The HMM will have the 4-digit MT and 3-digit CTO model only (Example:
1829-CTO). Again, CMVs are custom models and are not found in the HMM.
General Announce Variant (GAV)
This is a standard model (fixed configuration). GAVs are announced and offered to
all customers. The MTM portion of the machine label is a 4-digit MT and 3-digit
model, where model = a “fixed part number”, not “CTO” (Example: 1829-F1U).
Also, PEW, eSupport, and the HMM will list these products under the same fixed
model number.
FRU identification for CTO, CMV, and GAV products
There are three information resources to identify which FRUs are used to support
CTO, CMV, and GAV products. These sources are PEW, eSupport, and the HMM.
Using PEW
v PEW is the primary source for identifying FRU part numbers and FRU
descriptions for the key commodities for CTO, CMV and GAV products at a MT
- serial number level. An example of key commodities are hard disk drives,
system boards, microprocessors, Liquid Crystal Displays (LCDs), and memory.
v Remember, all CTO and CMV products are loaded in PEW under the 4-digit MT
and 3-digit model, where model = “CTO” (Example: 1829-CTO). GAVs are
loaded in PEW under the 4-digit MT and 3-digit model, where model = a “fixed
part number”, not “CTO” (Example: 1829-F1U).
Customers can also access PEW via
Important service information 19
Select Warranty lookup. Input the MT and the Serial number and the list of key
commodities will be returned in the PEW record under COMPONENT
INFORMATION.
v Business Partners using Eclaim will access PEW when performing Entitlement
Lookup. Business Partners will enter Loc ID, MT and Serial, and the key
commodities will be returned in the Eclaim record under SYSTEM DETAILS.
v Authorized IBM Business Partners can access Eclaim at the following Web site:
Using eSupport
For Key Commodities (Examples - hard disk drive, system board,
microprocessor, LCD, and memory)
v eSupport can be used to view the list of key commodities built in a particular
machine serial (this is the same record found in PEW).
v To view the key commodities, click on PARTS INFORMATION, then PARTS
LOOKUP. Type in the model type and serial number. The key commodities will
be returned in the eSupport record under PARTS SHIPPED WITH YOUR
SYSTEM.
For the Remaining FRUs (the complete list of FRUs at the MT Model level)
v eSupport can be used to view the complete list of FRUs for a machine type and
model.
v To view the complete list of FRUs, type in the machine type and model
(Example: 1829-CTO) under QUICK PATH. Under “View by Document Type”
select PARTS INFORMATION. Under “Filter by Category” select SERVICE
PARTS. Under “Parts Information by Date” select SYSTEM SERVICE PARTS. The
list of service parts by description, with applicable machine type model and FRU
will be displayed.
Using the HMM
For Key Commodities (Examples - hard disk drive, system board,
microprocessor, LCD, and memory)
Use the HMM as a back-up to PEW and eSupport to view the complete list of
FRUs at the MT Model level.
20 Lenovo 3000 N500 Hardware Maintenance Manual
Important information about replacing RoHS compliant FRUs
RoHS, The Restriction of Hazardous Substances in Electrical and Electronic
Equipment Directive (2002/95/EC) is a European Union legal requirement
affecting the global electronics industry. RoHS requirements must be
implemented on Lenovo products placed on the market after June 2006. Products
on the market before June 2006 are not required to have RoHS compliant parts.
If the original FRU parts are non compliant, replacement parts can also be non
compliant. In all cases if the original FRU parts are RoHS compliant, the
replacement part must also be RoHS compliant.
Note: RoHS and non-RoHS FRU part numbers with the same fit and function are
identified with unique FRU part numbers.
Lenovo plans to transition to RoHS compliance well before the implementation
date and expects its suppliers to be ready to support Lenovo’s requirements and
schedule in the EU. Products sold in 2005 and 2006, will contain some RoHS
compliant FRUs. The following statement pertains to these products and any
product Lenovo produces containing RoHS compliant FRUs.
RoHS compliant FRUs have unique FRU part numbers. Before or after the RoHS
implementation date, failed RoHS compliant parts must always be replaced using
RoHS compliant FRUs, so only the FRUs identified as compliant in the system
HMM or direct substitutions for those FRUs may be used.
Products marketed before June 2006
Products marketed after June 2006
Current or original
part
Replacement FRU
Current or original
part
Replacement FRU
Non-RoHS
Non-RoHS
Non-RoHS
RoHS
Can be Non-RoHS
Can be RoHS
Must be RoHS
Must be RoHS
Can sub to RoHS
Must be RoHS
Note: A direct substitution is a part with a different FRU part number that is
automatically shipped by the distribution center at the time of the order.
Important service information 21
22 Lenovo 3000 N500 Hardware Maintenance Manual
General checkout
This chapter presents following information:
The descriptions in this chapter apply to any Lenovo 3000 model that supports the
PC-Doctor® for DOS diagnostics program. Some descriptions might not apply to
your particular computer.
Before you go to the checkout guide, be sure to read the following important notes.
Important notes:
v Only certified trained personnel should service the computer.
v Before replacing any FRU, read the entire page on removing and replacing
FRUs.
v When you replace FRUs, use new nylon-coated screws.
v Be extremely careful during such write operations as copying, saving, or
formatting. Drives in the computer that you are servicing sequence might
have been altered. If you select an incorrect drive, data or programs might be
overwritten.
v Replace a FRU only with another FRU of the correct model. When you
replace a FRU, make sure that the model of the machine and the FRU part
number are correct by referring to the FRU parts list.
v A FRU should not be replaced because of a single, unreproducible failure.
Single failures can occur for a variety of reasons that have nothing to do with
a hardware defect, such as cosmic radiation, electrostatic discharge, or
software errors. Consider replacing a FRU only when a problem recurs. If you
suspect that a FRU is defective, clear the error log and run the test again. If
the error does not recur, do not replace the FRU.
v Be careful not to replace a nondefective FRU.
© Copyright Lenovo 2008
23
What to do first
When you do return a FRU, you must include the following information in the
parts exchange form or parts return form that you attach to it:
__ 1. Name and phone number of servicer
__ 2. Date of service
__ 3. Date on which the machine failed
__ 4. Date of purchase
__ 5. Failure symptoms, error codes appearing on the display, and beep
symptoms
__ 6. Procedure index and page number in which the failing FRU was detected
__ 7. Failing FRU name and part number
__ 8. Machine type, model number, and serial number
__ 9. Customer’s name and address
Note for warranty: During the warranty period, the customer may be responsible
for repair costs if the computer damage was caused by misuse, accident,
modification, unsuitable physical or operating environment, or improper
maintenance by the customer.
Following is a list of some common items that are not covered under warranty and
some symptoms that might indicate that the system was subjected to stress beyond
normal use.
Before checking problems with the computer, determine whether the damage is
covered under the warranty by referring to the following list:
The following are not covered under warranty:
v LCD panel cracked from the application of excessive force or from being
dropped
v Scratched (cosmetic) parts
v Distortion, deformation, or discoloration of the cosmetic parts
v Plastic parts, latches, pins, or connectors that have been cracked or broken by
excessive force
v Damage caused by liquid spilled into the system
v Damage caused by the improper insertion of a PC Card or the installation of an
incompatible card
v Improper disc insertion or use of an optical drive
v Diskette drive damage caused by pressure on the diskette drive cover, foreign
material in the drive, or the insertion of a diskette with multiple labels
v Damaged or bent diskette eject button
v Fuses blown by attachment of a nonsupported device
v Forgotten computer password (making the computer unusable)
v Sticky keys caused by spilling a liquid onto the keyboard
v Use of an incorrect ac adapter on laptop products
The following symptoms might indicate damage caused by nonwarranted
activities:
v Missing parts might be a symptom of unauthorized service or modification.
v If the spindle of a hard disk drive becomes noisy, it may have been subjected to
excessive force, or dropped.
24 Lenovo 3000 N500 Hardware Maintenance Manual
Checkout guide
Use the following procedures as a guide in identifying and correcting problems
with the Lenovo 3000 computer.
Note: The diagnostic tests are intended to test only Lenovo 3000 products. The use
of non-Lenovo 3000 products, prototype cards, or modified options can lead to
false indications of errors and invalid system responses.
1. Identify the failing symptoms in as much detail as possible.
2. Verify the symptoms. Try to re-create the failure by running the diagnostic test
or by repeating the operation.
General checkout 25
Diagnostics using PC-Doctor for DOS
The Lenovo 3000 computer has a test program called PC-Doctor for DOS (hereafter
called PC-Doctor.) You can detect errors by running the diagnostics test included in
PC-Doctor. This section is an overview of the procedure. For details that depend
on model-unique functions, refer to “Lenovo 3000 N500” on page 43.
For some possible configurations of the computer, PC-Doctor might not run
correctly. To avoid this problem, you need to initialize the computer setup by use
of the BIOS Setup Utility before you run PC-Doctor. On the BIOS Setup Utility
screen, press F9, Enter, F10, and then Enter.
Note: When you initialize the computer configuration, some devices are disabled,
such as the serial port. If you test one of these devices, you will need to enable it
by using Configuration utility for DOS. The utility is available on the following
Creating the PC-Doctor diagnostics diskette
To create the PC-Doctor disk from the Rescue and Recovery® workspace, do as
follows:
1. Enter the Rescue and Recovery workspace by pressing the Lenovo CareSM
button during POST.
2. When theRescue and Recovery workspace finishes loading, click Diagnostic
Diskette.
3. Authenticating the digital signature takes about 15 seconds; then the Lenovo
3000 computer will reboot into PC-DOS.
4. A batch file automatically starts up to prompt you through the process of
creating diskettes. You are notified of how many diskettes you will need.
a. You are prompted to insert each diskette in sequence.
b. Typically, all you need to do is to press the Enter key for the floppy drive;
the system then formats and creates the diskette.
c. Each diskette is erased and formatted with the PC-Doctor for DOS boot
image.
5. Once all the diskettes have been created, the Lenovo 3000 computer will reboot.
The user is asked to remove all diskettes from the drive, or to insert the first
diskette created if it is desired to run the diagnostics.
Testing the computer
To run the test, do as follows:
1. Insert the PC-Doctor disk into the diskette drive; then power on the computer.
If the computer cannot be powered on, go to “Power system checkout” on page
29, and check the power sources.
If an error code appears, go to “Symptom-to-FRU index” on page 36.
On the first screen, select the model and press Enter. Follow the instructions on
the screen.
2. The main panel of PC-Doctor appears.
3. Select Diagnostics with the arrow keys, and press Enter.
A pull-down menu appears. (Its exact form depends on the model.)
26 Lenovo 3000 N500 Hardware Maintenance Manual
Note: PC-Doctor menu does not mean the formal support device list. Some
unsupported device names may appear in the PC-Doctor menu.
Diagnostics
Interactive Tests
Hardware Info
Utility
Quit
F1=Help
Run Normal Test
Run Quick Test
CPU/Coprocessor
Systemboard
Video Adapter
Fixed Disks
Diskette Drives
PM Memory
PC-DOCTOR 2.0 Copyright 2008 PC-Doctor, Inc. All Rights Reser ved.
Use the cursor keys and ESC to move in menus. Press ENTER to select.
The options on the test menu are as follows:
Diagnostics
Interactive Tests
v Run Normal Test
v Run Quick Test
v CPU/Coprocessor
v Systemboard
v Keyboard
v Video
v Mouse
v System Load
v Video Adapter
v Fixed Disks
v Diskette Drives
v PM Memory
Notes:
v In the Keyboard test in Interactive Tests, the Fn key should be held down with
M key for at least 2 seconds; otherwise, it cannot be sensed.
v Video Adapter test supports only the LCD display on the Lenovo 3000
computer. If you have an external monitor attached to your computer, detach it
before running PC-Doctor for DOS.
4. Run the applicable function test.
5. Follow the instructions on the screen. If there is a problem, PC-Doctor shows
messages describing it.
6. To exit the test, select Quit — Exit Diag.
To cancel the test, press Esc.
Note: After running PC-Doctor, check the time and date on the system and reset
them if they are incorrect.
Detecting system information with PC-Doctor
PC-Doctor can detect the following system information:
Hardware Info
v System Configuration
v Memory Contents
v Physical Disk Drives
v Logical Disk Drives
v VGA Information
v IDE Drive Info
v PCI Information
v PNPISA Info
General checkout 27
v SMBIOS Info
v VESA LCD Info
v Hardware Events Log
Utility
v Run External Tests
v Surface Scan Hard Disk
v Benchmark System
v DOS Shell
v Tech Support Form
v Battery Rundown
v View Test Log
v Print Log
v Save Log
v Full Erase Hard Drive
v Quick Erase Hard Drive
PC-Doctor for Windows
This product is designed to help you troubleshoot and resolve problems related to
your computer. Select one of the categories listed below to display symptoms and
solutions:
v Check System Health
v System and Device Tests
v Lenovo Troubleshooting Center
v System Reports
v Updates and Support
28 Lenovo 3000 N500 Hardware Maintenance Manual
Power system checkout
To verify a symptom, do the following:
1. Turn off the computer.
2. Remove the battery pack.
3. Connect the ac adapter.
4. Check that power is supplied when you turn on the computer.
5. Turn off the computer.
6. Disconnect the ac adapter and install the charged battery pack.
7. Check that the battery pack supplies power when you turn on the computer.
If you suspect a power problem, see the appropriate one of the following power
supply checkouts:
Checking the AC adapter
You are here because the computer fails only when the AC adapter is used.
v If the power-on indicator does not turn on, check the power cord of the AC
adapter for correct continuity and installation.
To check the AC adapter, do the following:
1. Unplug the AC adapter cable from the computer.
2. Measure the output voltage at the plug of the AC adapter cable. See the
following figure:
Pin
1
Voltage (V dc)
+19
3
2
0
3
Ground
2
1
(20V)
Note: Output voltage of pin no.2 of the AC adapter may different from the one
you are servicing.
3. If the voltage is not correct, replace the AC adapter.
4. If the voltage is acceptable, do the following:
v Replace the system board.
Note: Noise from the AC adapter does not always indicate a defect.
Checking operational charging
To check whether the battery charges properly during operation, use a discharged
battery pack or a battery pack that has less than 50% of the total power remaining
when installed in the computer.
General checkout 29
Perform operational charging. If the battery status indicator or icon does not turn
on, remove the battery pack and let it return to room temperature. Reinstall the
battery pack. If the charge indicator or icon still does not turn on, replace the
battery pack.
If the charge indicator still does not turn on, replace the system board. Then
reinstall the battery pack. If it is still not charged, go to the next section.
Checking the battery pack
Battery charging does not start until the Power Meter shows that less than 95% of
the total power remains; under this condition the battery pack can charge to 100%
of its capacity. This protects the battery pack from being overcharged or from
having a shortened life.
To check your battery, move your cursor to the Power Meter icon in the icon tray
of the Windows® taskbar and wait for a moment (but do not click), and the
percentage of battery power remaining is displayed. To get detailed information
about the battery, double-click the Power Meter icon.
Note: If the battery pack becomes hot, it may not be able to charge. Remove it
from the computer and leave it at room temperature for a while. After it cools
down, reinstall and recharge it.
To check the battery pack, do the following:
1. Power off the computer.
2. Remove the battery pack and measure the voltage between battery terminals 1
(+) and 7 (-). See the following figure:
Terminal
Voltage (V dc)
+ 0 to + 12.6
Ground (-)
1
7
7(-)
6(-)
5
4
3
2(+)
1(+)
3. If the voltage is less than +11.0 V dc, the battery pack has been discharged.
Note: Recharging will take at least 3 hours, even if the indicator does not turn
on.
If the voltage is still less than +11.0 V dc after recharging, replace the battery.
4. If the voltage is more than +11.0 V dc, measure the resistance between battery
terminals 5 and 7. The resistance must be 4 to 30 K ꢀ.
If the resistance is not correct, replace the battery pack. If the resistance is
correct, replace the system board.
30 Lenovo 3000 N500 Hardware Maintenance Manual
Related service information
This chapter presents following information:
Service Web site:
When the latest maintenance diskette and the system program service diskette
become available, they will be posted on http://www.lenovo.com/spm
Restoring the factory contents by using Product Recovery discs
When the hard disk drive is replaced because of a failure, no Product Recovery
program is on the new hard disk. In this case, you must use the recovery disc for
the computer. Order the recovery disc and the hard disk drive at the same time so
that you can recover the new hard disk drive with the preinstalled software when
they arrive. For information on which disc to order, see “Recovery discs” on page
To install the factory contents by using Product Recovery discs, do the following:
Note: The recovery process might take up to 2 hours.
1. Make the optical drive the first start up device in the startup sequence.
2. Insert the bootable Rescue and Recovery Startup disc into the optical drive,
and then start the computer.
3. In the Rescue and Recovery workspace, complete the following procedure:
a. When the Rescue and Recovery workspace opens, click Continue on the
Welcome window and then click Restore your system.
b. When a message about accessing a USB device is displayed, click OK.
c. In the initial window of the ″Restore your system″ wizard, select Restore
my hard drive to the original factory state and click Next.
d. In the next window, select I do not want to save any files and click Next.
e. A warning opens not to turn off the computer during the recovery process.
Click OK.
4. When the Product Recovery window opens, click OK.
5. The Terms and Conditions window opens, select I accept these terms and
conditions and then click OK.
6. After the files necessary for the product recovery are copied from the Rescue
and Recovery Startup disc to the hard drive, the system restarts automatically
and boot back into Rescue and Recovery. Remove the disc and turn off the
computer.
7. Turn on the computer to continue the recovery process.
© Copyright Lenovo 2008
31
8. After you restart the computer, the computer prompts you for a supplemental
Rescue and Recovery disc. If you have a supplemental Rescue and Recovery
disc, click OK and insert the supplemental disc. If you do not have a
supplemental disc, click No.
9. When prompted, insert the appropriate Product Recovery disc and then click
OK. The second phase of the recovery process begins.
10. When all of the data has been copied from the last Product Recovery disc in
the set, a message is displayed prompting you to restart the computer.
Remove the disc and then click YES, then a message is displayed asking you
to continue the recovery process. Click Continue to restart your computer,
then the computer restarts and the third phase of the recovery process begins.
11. When the recovery process is complete, the Welcome to Microsoft Windows
screen is displayed. Follow the instructions on the screen to complete the
Windows setup.
Passwords
As many as three passwords may be needed for any Lenovo 3000 computer: the
power-on password (POP), the hard-disk password (HDP), and the supervisor
password (SVP).
If any of these passwords has been set, a prompt for it appears on the screen
whenever the computer is turned on. The computer does not start until the
password is entered.
Exception: If only an SVP is installed, the password prompt does not appear when
the operating system is booted.
Power-on password
A power-on password (POP) protects the system from being powered on by an
unauthorized person. The password must be entered before an operating system
can be booted.
Hard-disk password
There are two hard-disk passwords (HDPs):
v User HDP—for the user
v Master HDP—for the system administrator, who can use it to get access to the
hard disk even if the user has changed the user HDP
Note: There are two modes for the HDP: User only and Master + User. The
Master + User mode requires two HDPs; the system administrator enters both in
the same operation. The system administrator then provides the user HDP to the
system user.
Attention: If the user HDP has been forgotten, check whether a master HDP has
been set. If it has, it can be used for access to the hard disk drive. If no master
HDP is available, neither Lenovo nor Lenovo authorized servicers provide any
services to reset either the user or the master HDP, or to recover data from the
hard disk drive. The hard disk drive can be replaced for a scheduled fee.
32 Lenovo 3000 N500 Hardware Maintenance Manual
Supervisor password
A supervisor password (SVP) protects the system information stored in the BIOS
Setup Utility. The user must enter the SVP in order to get access to the BIOS Setup
Utility and change the system configuration.
Attention: If the SVP has been forgotten and cannot be made available to the
servicer, there is no service procedure to reset the password. The system board
must be replaced for a scheduled fee.
How to remove the hard-disk password
Attention: If User only mode is selected and the user HDP has been forgotten
and cannot be made available to the servicer, neither Lenovo nor Lenovo
authorized servicers provide any services to reset the user HDPs or to recover data
from the hard disk drive. The hard disk drive can be replaced for a scheduled fee.
To remove a user HDP that has been forgotten, when the SVP and the master HDP
are known, do the following:
1. Turn on the computer; then, while the initial screen is displayed, press the
Lenovo Care button. The Rescue and Recovery screen opens.
2. Click Access BIOS. The System Restart Required window is displayed.
3. Click Yes. The computer restarts, and the BIOS Setup Utility screen opens.
4. Select Security, using the cursor directional keys to move down the menu.
5. Select Password.
6. Select Hard-disk x password, where x is the letter of the hard disk drive. A
pop-up window opens.
7. Select Master HDP.
8. Type the current master HDP in the Enter Current Password field. then leave
the Enter New Password field blank, and press Enter twice.
9. Press F10.
10. Select Yes in the Setup Configuration window.
Both user HDP and master HDP will have been removed.
Related service information 33
Power management
Note: Power management modes are not supported for APM operating system.
To reduce power consumption, the computer has three power management modes:
screen blank, sleep (standby), and hibernation.
Screen blank mode
If the time set on the “Turn off monitor” timer in the operating system expires, the
LCD backlight turns off.
To put the computer into screen blank mode, press the Lenovo Care button and
use the ThinkVantage® Productivity Center.
To end screen blank mode and resume normal operation, press any key.
Sleep (standby) mode
When the computer enters sleep (standby) mode, the following events occur in
addition to what occurs in screen blank mode:
v The LCD is powered off.
v The hard disk drive is powered off.
v The CPU stops.
To enter sleep (standby) mode, press Fn+F4.
In certain circumstances, the computer goes into sleep (standby) mode
automatically:
v If a “suspend time” has been set on the timer, and the user does not do any
operation with the keyboard, the hard disk, the parallel connector, or the
diskette drive within that time.
v If the battery indicator blinks orange, indicating that the battery power is low.
(Alternatively, if Hibernate when battery becomes low has been selected in the
“Power Management Properties” window, the computer goes into hibernation
mode.)
To cause the computer to return from sleep (standby) mode and resume operation,
do one of the following:
v Press the Fn key.
v Open the LCD cover.
v Turn on the power switch.
Also, in the following event, the computer automatically returns from sleep
(standby) mode and resumes operation:
v The time set on the resume timer elapses.
Note: The computer does not accept any input immediately after it enters sleep
(standby) mode. Wait a few seconds before taking any action to reenter
operation mode.
34 Lenovo 3000 N500 Hardware Maintenance Manual
Hibernation mode
In hibernation mode, the following occurs:
v The system status, RAM, VRAM, and setup data are stored on the hard disk.
v The system is powered off.
To cause the computer to enter hibernation mode, do any of the following:
v Press the Fn+F12 keys.
v If you are using the ACPI operating system and have defined one of the
following actions as the event that causes the system to go into hibernation
mode, perform that action.
– Closing the lid.
– Pressing the power button.
Also, the computer goes into hibernation mode automatically in either of the
following conditions:
v If a “hibernation time” has been set on the timer, and if the user does not do
any operation with the keyboard, the hard disk drive, the parallel connector, or
the diskette drive within that time.
v If the timer conditions are satisfied in suspend mode.
When the power is turned on, the computer returns from hibernation mode and
resumes operation. The hibernation file in the boot record on the hard disk drive is
read, and system status is restored from the hard disk drive.
Related service information 35
Symptom-to-FRU index
This section contains following information:
The symptom-to-FRU index in this section lists symptoms and errors and their
possible causes. The most likely cause is listed first, in boldface type.
Note: Do the FRU replacement or other actions in the sequence shown in the
column headed “FRU or action, in sequence.” If replacing a FRU does not solve
the problem, put the original part back in the computer. Do not replace a
nondefective FRU.
This index can also help you determine, during regular servicing, what FRUs are
likely to need to be replaced next.
A numeric error is displayed for each error detected in POST or system operation.
In the displays, n can be any number.
If no numeric code is displayed, check the narrative descriptions of symptoms. If
the symptom is not described there, go to “Intermittent problems” on page 41.
Note:
For a device not supported by diagnostic codes in the Lenovo 3000 computers,
see the manual for that device.
Numeric error codes
Table 1. Numeric error codes
Symptom or error
FRU or action, in sequence
0200
1. Reseat the hard disk drive.
2. Load Setup Defaults in BIOS Setup
Utility.
Hard disk error—The hard disk is not
working.
3. Hard disk drive.
4. System board.
021x
Keyboard error.
Run interactive tests of the keyboard and
the auxiliary input device.
0220
Load Setup Defaults in BIOS Setup Utility.
Monitor type error—Monitor type does not
match the one specified in CMOS.
0230
System board.
Shadow RAM error—Shadow RAM fails at
offset nnnn.
0231
1. DIMM.
System RAM error—System RAM fails at
offset nnnn.
2. System board.
36 Lenovo 3000 N500 Hardware Maintenance Manual
Table 1. Numeric error codes (continued)
Symptom or error
0232
FRU or action, in sequence
1. DIMM.
Extended RAM error— Extended RAM fails 2. System board.
at offset nnnn.
0250
1. Charge the backup battery for more
System battery error—System battery is
dead.
than 8 hours by connecting the ac
adapter.
2. Replace the backup battery and run BIOS
Setup Utility to reset the time and date.
0251
1. Charge the backup battery for more
than 8 hours by connecting the ac
adapter.
System CMOS checksum bad— Default
configuration used.
2. Replace the backup battery and run BIOS
Setup Utility to reset the time and date.
0260
1. Charge the backup battery for more
than 8 hours by connecting the ac
adapter.
System timer error.
2. Replace the backup battery and run BIOS
Setup Utility to reset the time and date.
3. System board.
0270
1. Charge the backup battery for more
than 8 hours by connecting the ac
adapter.
Real-time clock error.
2. Replace the backup battery and run BIOS
Setup Utility to reset the time and date.
3. System board.
0280
1. Load “Setup Default” in BIOS Setup
Previous boot incomplete— Default
configuration used.
Utility.
2. DIMM.
3. System board.
02F4
1. Load Setup Defaults in BIOS Setup
Utility.
EISA CMOS not writable.
2. Replace the backup battery.
3. System board.
02F5
1. DIMM.
DMA test failed.
2. System board.
02F6
1. DIMM.
Software NMI failed
2. System board.
02F7
1. DIMM.
Fail-safe timer NMI failed
2. System board.
Related service information 37
Error messages
Table 2. Error messages
Symptom or error
FRU or action, in sequence
Unsupported memory.
DIMM. Make sure to use supported
memory.
Device address conflict.
1. Load “Setup Defaults” in the BIOS
Setup Utility.
2. Backup battery.
3. System board.
Allocation error for device.
1. Load “Setup Defaults” in the BIOS
Setup Utility.
2. Backup battery.
3. System board.
Failing bits: nnnn.
1. DIMM.
2. System board.
Invalid system configuration data.
I/O device IRQ conflict.
1. DIMM.
2. System board.
1. Load “Setup Defaults” in the BIOS
Setup Utility.
2. Backup battery.
3. System board.
Hibernation error.
1. Restore the system configuration to
what it was before the computer
entered hibernation mode.
2. If memory size has been changed,
re-create the hibernation file.
Fan error.
1. Fan.
2. Thermal grease.
3. System board.
Thermal sensing error.
System board.
Authentication of system services failed.
Press <Esc> to resume.
The Predesktop Area in the HDD is
corrupted. Restore it from a recovery disc.
Cannot boot from any device.
Check the status of device which you want
to boot from.
Device not found.
1. The device you want to boot from.
2. System board.
Device Error.
1. The device you want to boot from.
2. System board.
No valid operating system.
1. Check that the operating system has no
failure and is installed correctly.
2. Reinstall the operation system.
Excluded from boot order.
v Enter the BIOS Setup Utility and add the
device in boot order.
38 Lenovo 3000 N500 Hardware Maintenance Manual
Beep symptoms
Table 3. Beep symptoms
Symptom or error
FRU or action, in sequence
One beep and a blank, unreadable, or
flashing LCD.
1. Reseat the LCD connector.
2. LCD assembly.
3. External CRT.
4. System board.
One long and two short beeps, and a blank 1. System board.
or unreadable LCD.
2. LCD assembly.
3. DIMM.
Two short beeps with error codes.
Two short beeps and a blank screen.
POST error. See “Numeric error codes” on
1. System board.
2. DIMM.
Three short beeps, pause, three more short
beeps, and one short beep.
1. DIMM.
2. System board
One short beep, pause, three short beeps,
pause, three more short beeps, and one short
beep.
Only the cursor appears.
Reinstall the operating system.
Four cycles of four short beeps and a blank System board (security chip)
screen.
Five short beeps and a blank screen.
System board
No-beep symptoms
Table 4. No-beep symptoms
Symptom or error
FRU or action, in sequence
No beep, power-on indicator on, LCD blank, 1. Make sure that every connector is
and no POST.
connected tightly and correctly.
2. DIMM.
3. System board.
No beep, power-on indicator on, and LCD
blank during POST.
1. Reseat DIMM.
2. System board.
The power-on password prompt appears.
A power-on password or a supervisor
password is set. Type the password and
press Enter.
The hard-disk password prompt appears.
A hard-disk password is set. Type the
password and press Enter.
Related service information 39
LCD-related symptoms
Important: The TFT LCD for the notebook computer contains many thin-film
transistors (TFTs). The presence of a small number of dots that are missing,
discolored, or always lighted is characteristic of TFT LCD technology, but
excessive pixel problems can cause viewing concerns. The LCD should be
replaced if the number of missing, discolored, or lighted dots in any background
is as follows:
Table 5. Minimum quantity of defective pixels required for LCD replacement on June 2006
or later manufactured Lenovo 3000
LCD resolution
Bright dots
Dark dots
Bright and dark dots
XGA, WXGA
5
5
6
8
6
WXGA+, SXGA+,
WSXGA+
10
UXGA, WUXGA,
QXGA
5
13
13
Notes:
v Lenovo will not provide replacement if the LCD is within specification as we
cannot guarantee that any replacement LCD will have zero pixel defects.
v A bright dot means a pixel is always on (white or color.)
v A dark dot means a pixel is always off (black color.)
v One pixel consists of R, G, B sub-pixels.
Table 6. LCD-related symptoms
Symptom or error
FRU or action, in sequence
No beep, power-on indicator on, and a
blank LCD during POST.
System board.
v LCD backlight not working.
v LCD too dark.
1. Reseat the LCD connectors.
2. LCD assembly.
3. System board.
v LCD brightness cannot be adjusted.
v LCD contrast cannot be adjusted.
v LCD screen unreadable.
v Characters missing pixels.
v Screen abnormal.
1. See important note for “LCD-related
symptoms.”
2. Reseat all LCD connectors.
3. LCD assembly.
v Wrong color displayed.
4. System board.
Horizontal or vertical lines displayed on
LCD.
LCD assembly.
40 Lenovo 3000 N500 Hardware Maintenance Manual
Intermittent problems
Intermittent system hang problems can be due to a variety of causes that have
nothing to do with a hardware defect, such as cosmic radiation, electrostatic
discharge, or software errors. FRU replacement should be considered only when a
problem recurs.
When analyzing an intermittent problem, do the following:
1. Run the diagnostic test for the system board in loop mode at least 10 times.
2. If no error is detected, do not replace any FRUs.
3. If any error is detected, replace the FRU shown by the FRU code. Rerun the
test to verify that no more errors exist.
Undetermined problems
If the diagnostic tests did not identify the adapter or device that has failed, if
wrong devices are installed, or if the system simply is not operating, follow these
procedures to isolate the failing FRU (do not isolate FRUs that have no defects).
Verify that all attached devices are supported by the computer.
Verify that the power supply being used at the time of the failure is operating
1. Turn off the computer.
2. Visually check each FRU for damage. Replace any damaged FRU.
3. Remove or disconnect all of the following devices:
a. Non-Lenovo 3000 devices
b. Devices attached to the docking station or the port replicator
c. Printer, mouse, and other external devices
d. Battery pack
e. Hard disk drive
f. External diskette drive or optical drive
g. DIMM
h. Optical disk or diskette in the internal drive
i. PC Cards
4. Turn on the computer.
5. Determine whether the problem has been solved.
6. If the problem does not recur, reconnect the removed devices one at a time
until you find the failing FRU.
7. If the problem remains, replace the following FRUs one at a time (do not
replace a nondefective FRU):
a. System board
b. LCD assembly
Related service information 41
42 Lenovo 3000 N500 Hardware Maintenance Manual
Lenovo 3000 N500
This chapter presents following product-specific service references and
product-specific parts information.
Specifications
The following table lists the specifications of the Lenovo 3000 N500 :
Table 7. Specifications
Feature
Description
Processor
v Intel® Celeron M processor 575 (2.0 GHz), 1-MB L2 cache
v Intel Celeron M processor 585 (2.16 GHz), 1-MB L2 cache
v Intel Pentium dual-core processor T3200 (2.0 GHz), 1-MB
L2 cache
v Intel Pentium dual-core processor T3400 (2.16 GHz), 1-MB
L2 cache
v Intel® Core™ 2 Duo processor P7350 (2.0 GHz), 3-MB L2
cache
v Intel Core 2 Duo processor PP8400 (2.26 GHz), 3-MB L2
cache
v Intel Core 2 Duo processor P8600 (2.4 GHz), 3-MB L2
cache
v Intel Core 2 Duo processor P9500 (2.53 GHz), 6-MB L2
cache
v Intel Core 2 Duo processor T5670 (1.8 GHz), 2-MB L2
cache
v Intel Core 2 Duo processor T5800 (2.0 GHz), 2-MB L2
cache
v Intel Core 2 Duo processor T5900 (2.2 GHz), 2-MB L2
cache
v Intel Core 2 Duo processor T9400 (2.53 GHz), 6-MB L2
cache
v Intel Core 2 Duo processor T9600 (2.80 GHz), 6-MB L2
cache
Bus architecture
v 800-MHz PSB
v 667-MHz DDR2 SDRAM (PC2-5300)
v PCI bus
v PCI Express bus
v DMI
Graphic memory chip
Display
v Intel GMA 4500 Integrated Graphics
v Intel GMA X4500 Integrated Graphics
v nVidia GeForce 9300 256 MB
v 15.4-inch, 16M colors, WXGA (1280 × 800 resolution) TFT
color LCD
© Copyright Lenovo 2008
43
Table 7. Specifications (continued)
Feature
Description
Standard memory
v 1-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1
v 2-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1
Optional memory
v 1-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1
v 2-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1
(maximum of 4.0 GB)
CMOS RAM
v 242 bytes
Hard disk drive
v 160 GB, 5400 rpm, 9.5 mm high, SATA interface
v 250 GB, 5400 rpm, 9.5 mm high, SATA interface
v 320 GB, 5400 rpm, 9.5 mm high, SATA interface
Supported hard disk drives depend on the model.
Optical drive
I/O port
v DVD/CD-RW combo drive, 12.7 mm high
v DVD multi drive, 12.7 mm high
v External monitor connector
v Stereo headphone jack
v Monaural microphone jack
v Docking connector
v RJ11 connector
v RJ45 connector
v Universal serial bus (USB) connector × 4 (compatible with
USB 1.1 and 2.0)
v 4-in-1 media card reader
Internal modem
Audio
v 56.6 Kbps
v Built-in stereo speakers
v Software control volume
Ethernet (on the system
board)
v 10/100M Ethernet
PCI Express Mini Card
v Lenovo 802.11b/g Wireless LAN Mini-PCI Express
Adapter
v Intel WiFi Link 5100
ExpressCard slot
v One ExpressCard slot and one PC Card (Type-II) slot
v One Smart Card slot and one PC Card (Type-II) slot
Bluetooth wireless (some
models)
v Lenovo 3000 Bluetooth with Enhanced Data Rate (BDC-2.1)
Modem
v Lenovo 3000 Modem (MDC-1.5, 56 kbps HDA)
Touch pad
Integrated camera
Battery
Yes
Some models
v Li-ion battery (6 cells) 2.4 Ah
v Li-ion battery (6 cells) 2.6 Ah
AC adapter
v 65-watt type
v 90-watt type
Preinstalled operating
system
v Windows Vista® Home Basic (32 bit)
v Windows Vista Home Premium (32 bit)
v Windows Vista Business (32 bit)
44 Lenovo 3000 N500 Hardware Maintenance Manual
Status indicators
The system status indicators show the status of the computer, as follows:
7
6
5
1
2
3
4
Table 8. Status indicators
Indicator
Meaning
Blue:
ꢀ1ꢁ
Drive in use
Data is being read from or written to the hard disk
drive, the solid state drive, or the optical disk drive.
When this indicator is on, do not put the computer into
standby mode or turn off the computer.
Note: Do not move the system while the green drive-in-use light
is on. Sudden physical shock could cause drive errors.
ꢀ2ꢁ
ꢀ3ꢁ
ꢀ4ꢁ
ꢀ5ꢁ
Caps lock
Blue:
Blue:
Blue:
Caps Lock mode is enabled. To enable or disable Caps
Lock mode, press the Caps Lock key.
Num lock
The numeric keypad on the keyboard is enabled. To
enable or disable the keypad, press and hold the Shift
key, and press the NumLk key.
Scroll lock
Wireless status
Scroll Lock mode is enabled. To enable or disable Scroll
Lock mode, press and hold the Shift key, and press the
ScrLk key.
Purple: The wireless LAN and the Bluetooth features are on, and
the radio link is ready for use.
Orange:
The Bluetooth feature is on, and the radio link is ready
for use.
Blue:
The wireless LAN feature is on, and the radio link is
ready for use.
Blinking blue:
The wireless LAN feature is on, and the networks are
being scanned.
Lenovo 3000 N500 45
Table 8. Status indicators (continued)
Indicator
ꢀ6ꢁ Battery status
Meaning
Blue:
The battery is charged to 95% or more of its capacity.
Blinking blue:
The battery is being trickle-charged.
Orange:
Off:
The battery is being normally charged.
The computer is operating on battery power, and the
battery has enough power.
Blinking orange:
The computer is operating on battery power, and the
battery is charged to no more than 8% of capacity.
ꢀ7ꢁ
Power on
Blue:
The computer is on and ready to use. This indicator
stays on whenever the computer is on and is not in
standby mode.
46 Lenovo 3000 N500 Hardware Maintenance Manual
FRU tests
The following table shows the test for each FRU.
Table 9. FRU tests
FRU
Applicable test
System board
1. Diagnostics --> CPU/Coprocessor
2. Diagnostics --> Systemboard
LCD unit
Keyboard
1. Diagnostics --> Video Adapter
2. Interactive Tests --> Video
1. Diagnostics --> Systemboard --> Keyboard
2. Interactive Tests --> Keyboard
Hard disk drive
Diskette drive
Memory
Diagnostics --> Fixed Disks
Diagnostics --> Diskette Drives
1. If two DIMMs are installed, remove one of them and run
Diagnostics --> PM Memory.
2. If the problem does not recur, return the DIMM to its place,
remove the other one, and run the test again.
3. If the test does not detect the error, run Diagnostics --> PM
Memory.
Lenovo 3000 N500 47
Fn key combinations
The following table shows the function of each combination of Fn with a function
key.
Table 10. Fn key combinations
Key combination Description
Fn+F1
Fn+F2
Fn+F3
Fn+F4
Fn+F5
Volume down.
Volume up.
Reserved.
Reserved.
Enable or disable the built-in wireless networking features and the
Bluetooth features. If you press Fn+F5, a list of wireless features is
displayed. You can quickly change the power state of each feature in
the list.
Fn+F6
Fn+F7
Reserved.
Open the window for Choose Presentation or Display scheme. If you
press this combination of keys, a list of schemes is displayed in the
window. You can quickly select a scheme in the list.
Fn+F8
Reserved.
Fn+F9
Reserved.
Fn+F10
Fn+F11
Fn+F12
Make the computer display less bright.
Make the computer display brighter.
Put the computer into hibernation mode. To return to normal operation,
press the power button.
Fn+Esc
Mute the sound from the computer.
Scroll Lock (ScrLk).
Fn+Insert
Fn+Delete
Fn+PrtSc
Numeric Lock (NmLk).
Has the same function as the SysRq key.
Has the same function as the Break key.
Has the same function as the Home key.
Has the same function as the End key.
Fn+Pause
Fn+PgUp
Fn+PgDn
Fn+cursor keys
These key combinations work with Windows Media Player. Fn+down
arrow key works for the Play or Pause button, Fn+up arrow key for the
Stop button, Fn+right arrow key for the Next Track button, and Fn+left
arrow key for the Previous Track button.
48 Lenovo 3000 N500 Hardware Maintenance Manual
FRU replacement notices
This section contains notices related to removing and replacing parts. Read this
section carefully before replacing any FRU.
Screw notices
Loose screws can cause a reliability problem. In the Lenovo 3000 computer, this
problem is addressed with special nylon-coated screws that have the following
characteristics:
v They maintain tight connections.
v They do not easily come loose, even with shock or vibration.
v They are harder to tighten.
v Each one should be used only once.
Do the following when you service this machine:
tool bag.
v Always use new screws.
v Use a torque screwdriver if you have one.
Tighten screws as follows:
v Plastic to plastic
Turn an additional 90 degrees after the screw head touches the surface of the
plastic part:
90 degrees more
(Cross-section)
v Logic card to plastic
Turn an additional 180 degrees after the screw head touches the surface of the
logic card:
180 degrees more
(Cross-section)
v Torque driver
If you have a torque driver, refer to the “Torque” column for each step.
v Make sure that you use the correct screw. If you have a torque screwdriver,
tighten all screws firmly to the torque shown in the table. Never use a screw
that you removed. Use a new one. Make sure that all of the screws are
tightened firmly.
v Ensure torque screw drivers are calibrated correctly following country
specifications.
Lenovo 3000 N500 49
Retaining serial numbers
This section includes the following descriptions:
Restoring the serial number of the system unit
When the computer was manufactured, the EEPROM on the system board was
loaded with the serial numbers of the system and all major components. These
numbers need to remain the same throughout the life of the computer.
If you replace the system board, you must restore the serial number of the system
unit to its original value.
Before replacing the system board, save the original serial number by doing the
following:
1. Install the CE Utility Diskette for Lenovo 3000 notebooks, and restart the
computer.
2. From the main menu, select 1. Set System Identification.
3. Select 2. Read S/N data from EEPROM.
The serial number of each device in your computer is displayed; the serial number
of the system unit is listed as follows:
v 20: Serial number
Write down that number.
Note: The serial number of the system unit is also written on the label attached to
the bottom of the computer.
After you have replaced the system board, restore the serial number by doing the
following:
1. Install the CE Utility Diskette for Lenovo 3000 notebooks and restart the
computer.
2. From the main menu, select 1. Set System Identification.
3. Select 1. Add S/N data from EEPROM.
Follow the instructions on the screen.
If the MTM and Product ID numbers differ from each other on the rear label, use
what is shown for the Product ID field. See example below:
MTM on rear label:
TTTT-CTO S/N SSSSSSS
Product ID on rear label:
TTTT-MMM (Use this number when setting Serial Number)
In the example, the Serial Number to be input is ’1STTTTMMMSSSSSSS’.
Retaining the UUID
The Universally Unique Identifier (UUID) is a 128-bit number uniquely assigned to
your computer at production and stored in the EEPROM of your system board.
The algorithm that generates the number is designed to provide unique IDs until
the year A.D. 3400. No two computers in the world have the same number.
50 Lenovo 3000 N500 Hardware Maintenance Manual
When you replace the system board, you must set the UUID on the new system
board as follows:
1. Install the CE Utility Diskette for Lenovo 3000 notebooks, and restart the
computer.
2. From the main menu, select 4. Assign UUID.
A new UUID is created and written. If a valid UUID already exists, it is not
overwritten.
Lenovo 3000 N500 51
Reading or writing the ECA information
Information on Engineering Change Announcements (ECA) are stored in the
EEPROM of the system board. The electronic storage of this information simplifies
the procedure to check if the ECA has been previously applied to a machine. The
machine does not need to be disassembled to check for the ECA application.
To check what ECAs have been previously applied to the machine, use the ECA
Information Read/Write function on the CE Utility Diskette for Lenovo 3000
notebooks.
1. Insert the CE Utility Diskette for Lenovo 3000 notebooks, and restart the
computer.
2. From the main menu, select 6. Set ECA Information.
3. To read ECA information, select 2. Read ECA/rework number from EEPROM
and follow the instruction.
4. To read box build date, select 5. Read box build date from EEPROM, and
follow the instruction on the screen.
After an ECA has been applied to the machine, the EEPROM must be updated to
reflect the ECA’s application. Use the CE Utility Diskette for Lenovo 3000
notebooks to update the EEPROM.
Note: Only the ECA number is stored in the EEPROM. The machine type of the
ECA is assumed be the same as the machine type of the machine that had the ECA
applied to it.
1. Insert the CE Utility Diskette for Lenovo 3000 notebooks, and restart the
computer.
2. From the main menu, select 6. Set ECA Information.
3. To write ECA information, select 1. Write ECA/rework number from EEPROM,
and follow the instruction.
4. To write box build date, select 4. Write box build date from EEPROM, and
follow the instruction on the screen.
If the system board is being replaced, try to read the ECA information from the old
system board and transfer the information to the new system. If the system board
is inoperable, this will not be possible.
52 Lenovo 3000 N500 Hardware Maintenance Manual
Removing and replacing a FRU
This section presents directions and drawings for use in removing and replacing a
FRU. Be sure to observe the following general rules:
1. Do not try to service any computer unless you have been trained and certified.
An untrained person runs the risk of damaging parts.
3. Begin by removing any FRUs that have to be removed before the failing FRU.
Any such FRUs are listed at the top of the page. Remove them in the order in
which they are listed.
4. Follow the correct sequence in the steps for removing the FRU, as given in the
drawings by the numbers in square callouts.
5. When turning a screw to replace a FRU, turn it in the direction as given by the
arrow in the drawing.
6. When removing the FRU, move it in the direction as given by the arrow in the
drawing.
7. To put the new FRU in place, reverse the removal procedure and follow any
notes that pertain to replacement. For information about connecting and
arranging internal cables, see “Locations” on page 93.
8. When replacing a FRU, use the correct screw as shown in the procedures.
DANGER
Before removing any FRU, turn off the computer, unplug all power cords from
electrical outlets, remove the battery pack, and then disconnect any
interconnecting cables.
Attention: After replacing a FRU, do not turn on the computer until you have
made sure that all screws, springs, and other small parts are in place and none are
loose inside the computer. Verify this by shaking the computer gently and listening
for rattling sounds. Metallic parts or metal flakes can cause electrical short circuits.
Attention: The system board is sensitive to, and can be damaged by, electrostatic
discharge. Before touching it, establish personal grounding by touching a ground
point with one hand or by using an electrostatic discharge (ESD) strap (P/N
6405959).
Lenovo 3000 N500 53
1010 Battery pack
DANGER
Use only the battery specified in the parts list for your computer. Any other
battery could ignite or explode.
Table 11. Removal steps of battery pack
Unlock the battery release lever ꢀ1ꢁ. Holding the battery release lever in the
unlocked position ꢀ2ꢁ, remove the battery pack in the direction shown by arrow
ꢀ3ꢁ.
1
1
3
2
2
When installing: Install the battery pack along the slide rails of the slot. Then
make sure that the battery release lever is in the locked position.
54 Lenovo 3000 N500 Hardware Maintenance Manual
1030 Hard disk drive (HDD) slot cover and HDD
For access, remove this FRU:
Attention:
v Do not drop the hard disk drive or apply any physical shock to it. The hard
disk drive is sensitive to physical shock. Improper handling can cause damage
and permanent loss of data.
v Before removing the drive, have the user make a backup copy of all the
information on it if possible.
v Never remove the drive while the system is operating or is in suspend mode.
Table 13. Removal steps of HDD slot cover and HDD
2
1
3
When installing: Make sure that the HDD connector is attached firmly.
56 Lenovo 3000 N500 Hardware Maintenance Manual
Table 13. Removal steps of HDD slot cover and HDD (continued)
4
Lenovo 3000 N500 57
1060 DIMM
For access, remove these FRUs in order:
Table 16. Removal steps of DIMM
1
2
1
Note: If only one DIMM is used on the computer you are servicing, the card
must be installed in SLOT-0 (ꢀaꢁ: lower slot), but not in SLOT-1 (ꢀbꢁ: upper
slot).
b
a
When installing: Insert the notched end of the DIMM into the socket. Press the
DIMM firmly, and pivot it until it snaps into the place. Make sure that it is
firmly fixed in the slot and does not move easily.
60 Lenovo 3000 N500 Hardware Maintenance Manual
1070 Fan assembly
For access, remove these FRUs in order:
Table 17. Removal steps of fan assembly
1
1
1
2
Step
Screw (quantity)
Color
Torque
ꢀ1ꢁ
M2.5 × 5 mm, wafer-head, nylon-coated (3) Silver
2.0 Nm
(2.5 kgfcm)
When installing: Make sure that the fan connector is attached firmly to the
system board.
Lenovo 3000 N500 61
Table 17. Removal steps of fan assembly (continued)
3
62 Lenovo 3000 N500 Hardware Maintenance Manual
1080 Heat sink assembly
For access, remove these FRUs in order:
Table 18. Removal steps of heat sink assembly
Note: Step ꢀ5ꢁ is only for the models with discrete graphics chip. For the
models with integrated graphics chip, skip the step ꢀ5ꢁ.
2
4
3
1
5
Step
Screw (quantity)
Color
Torque
ꢀ1ꢁ to M2.5 × 5 mm with spring, nylon-coated (4) Silver
ꢀ4ꢁ
2.0 Nm
(2.5 kgfcm)
ꢀ5ꢁ
M2.5 × 5 mm, wafer-head, nylon-coated (3) Silver
2.0 Nm
(2.5 kgfcm)
Lenovo 3000 N500 63
Table 18. Removal steps of heat sink assembly (continued)
Attention: Do not handle the heat sink assembly roughly. Improper handling of
the heat sink assembly can cause distortion or deformation and imperfect
contact with components.
6
When installing: Before you attach the fan assembly to the computer, apply
thermal grease, at an amount of 0.2 grams, on the part marked ꢀaꢁ as in the
following figure. Either too much or too less application of grease can cause a
thermal problem due to imperfect contact with a component. You also need to
peel the thin film off from the rubber ꢀbꢁ. In models with the discrete graphics
chip, there is an additional thermal rubber ꢀcꢁ whose film to be peeled off.
a
c
b
64 Lenovo 3000 N500 Hardware Maintenance Manual
1090 Wireless LAN card slot cover and PCI Express Mini Card
for wireless LAN
For access, remove this FRU in order:
Table 19. Removal steps of Wireless LAN card slot cover and PCI Express Mini Card for
wireless LAN
Note: Loosen the screws ꢀ1ꢁ, but do not remove them.
1
In step ꢀ3ꢁ, unplug the jacks by using the removal tool antenna RF connector
(P/N: 08K7159) or pick the connectors with your fingers and gently unplug
them in direction of the arrow.
Note: Some models might have three antenna cables in step ꢀ3ꢁ.
4
4
3
3
Step
Screw (quantity)
Color
Torque
ꢀ4ꢁ
M2 × 3 mm, wafer-head, nylon-coated (2)
Black
1.5 Nm
(2.0 kgfcm)
Lenovo 3000 N500 65
Table 19. Removal steps of Wireless LAN card slot cover and PCI Express Mini Card for
wireless LAN (continued)
5
When installing:
v In models with wireless LAN card that has two antenna connectors, plug the
gray cable into the jack labeled MAIN, and the black cable into the jack
labeled AUX on the card. If the computer you are servicing has three cables,
put the white cable in the cable holder.
v In models with wireless LAN card that has three antenna connectors, plug the
gray cable (MAIN) into the jack labeled TR1, the white cable (3rd) into jack
labeled R0 or TR3, and the black cable (AUX) into jack labeled TR2 on the
card.
66 Lenovo 3000 N500 Hardware Maintenance Manual
1100 CPU
For access, remove these FRUs in order:
Attention: CPU is extremely sensitive. When you service the CPU, avoid any
kind of rough handling.
Table 20. Removal steps of CPU
Rotate the head of the screw in the direction shown by arrow ꢀ1ꢁ to release the
lock; then remove the CPU.
1
a
b
2
When installing: Place the CPU on the CPU socket ꢀaꢁ, and then rotate the head
of the screw in the direction shown by arrow ꢀbꢁ to secure the CPU.
Lenovo 3000 N500 67
1110 Keyboard cover and power board
For access, remove this FRU in order:
Note: Power board is attached to the keyboard cover.
Table 21. Removal steps of keyboard cover and power board
1
1
1
1
Step
Screw (quantity)
Color
Torque
ꢀ1ꢁ
M2 × 2.5 mm, wafer-head, nylon-coated (4) Black
1.0 Nm
(1.5 kgfcm)
3
3
3
3
3
2
68 Lenovo 3000 N500 Hardware Maintenance Manual
Table 21. Removal steps of keyboard cover and power board (continued)
6
5
5
4
When installing: Make sure that the FPC connector is attached firmly.
8
9
8
10
7
7
When installing: Make sure that the FPC connector is attached firmly.
Step
Screw (quantity)
Color
Torque
ꢀ7ꢁ
M2 × 3 mm, wafer-head, nylon-coated (2)
Silver
1.5 Nm
(2.0 kgfcm)
Lenovo 3000 N500 69
1120 Bluetooth daughter card (BDC-2.1)
For access, remove these FRUs in order:
Table 22. Removal steps of BDC-2.1
1
2
3
Step
Screw (quantity)
M2 × 3 mm, wafer-head, nylon-coated (1)
Color
Torque
ꢀ1ꢁ
Silver
1.0 Nm
(1.5 kgfcm)
When installing: Make sure that connector is attached firmly.
70 Lenovo 3000 N500 Hardware Maintenance Manual
Table 23. Removal steps of keyboard (continued)
Lift the keyboard a little in the direction shown by arrow ꢀ2ꢁ, and then detach
the connector ꢀ3ꢁ.
2
3
4
3
When installing: Make sure that the FPC connector is attached firmly.
72 Lenovo 3000 N500 Hardware Maintenance Manual
Table 24. Removal steps of LCD unit (continued)
Peel off the tapes securing the antenna cables ꢀ2ꢁ. Then release the cables from
the guide hole of the system board ꢀ3ꢁ and the cable guides ꢀ4ꢁ.
4
5
2
3
6
5
When installing:
1. Route the antenna cables along the cable guides and secure them with the
tapes. As you route the cables, make sure that they are not subjected to any
tension. Tension could cause the cables to be damaged by the cable guides,
or a wire to be broken.
2. Make sure that the LCD connector is attached firmly.
7
7
Step
Screw (quantity)
Color
Torque
ꢀ7ꢁ
M2.5 × 8 mm, wafer-head, nylon-coated (4) Black
2.0 Nm
(2.5 kgfcm)
74 Lenovo 3000 N500 Hardware Maintenance Manual
Table 24. Removal steps of LCD unit (continued)
8
8
Lenovo 3000 N500 75
1150 Keyboard bezel and LED board L
For access, remove these FRUs in order:
Note: LED board L is attached to the keyboard bezel.
Table 25. Removal steps of keyboard bezel and LED board L
2
1
2
1
2
2
2
2
2
2
2
Step
Screw (quantity)
Color
Torque
ꢀ1ꢁ
M2 × 2.5 mm, wafer-head, nylon-coated (2) Black
1.0 Nm
(1.5 kgfcm)
ꢀ2ꢁ
M2.5 × 8 mm, wafer-head, nylon-coated (9) Black
2.0 Nm
(2.5 kgfcm)
76 Lenovo 3000 N500 Hardware Maintenance Manual
Table 25. Removal steps of keyboard bezel and LED board L (continued)
3
3
3
3
3
3
Step
Screw (quantity)
Color
Torque
ꢀ3ꢁ
M2.5 × 5 mm, small-head, nylon-coated (6) Black
2.0 Nm
(2.5 kgfcm)
5
5
4
4
4
4
4
5
6
4
When installing: Make sure that all the FPC connectors and the cable are
attached firmly.
Lenovo 3000 N500 77
Table 25. Removal steps of keyboard bezel and LED board L (continued)
7
8
8
10
9
Step
Screw (quantity)
M2 × 3 mm, wafer-head, nylon-coated (2)
Color
Torque
ꢀ8ꢁ
Silver
2.0 Nm
(2.5 kgfcm)
78 Lenovo 3000 N500 Hardware Maintenance Manual
1170 System board and ExpressCard slot assembly
Important notices for handling the system board:
When handling the system board, bear the following in mind.
v Be careful not to drop the system board on a bench top that has a hard
surface, such as metal, wood, or composite.
v Avoid rough handling of any kind.
v At every point in the process, be sure not to drop or stack the system board.
v If you put a system board down, be sure to put it only on a padded surface
such as an ESD mat or conductive corrugated material.
For access, remove these FRUs in order:
Note: ExpressCard slot assembly is attached to the system board.
Table 27. Removal steps of system board, PC Card/ExpressCard slots assembly
1
When installing: Make sure that the connector is attached firmly.
80 Lenovo 3000 N500 Hardware Maintenance Manual
Table 27. Removal steps of system board, PC Card/ExpressCard slots assembly (continued)
2
4
4
3
When installing: Make sure that the connectors are attached firmly.
Step
Screw (quantity)
Color
Torque
ꢀ4ꢁ
M2.5 × 5 mm, wafer-head, nylon-coated (2) Black
2.0 Nm
(2.5 kgfcm)
Lenovo 3000 N500 81
Table 27. Removal steps of system board, PC Card/ExpressCard slots assembly (continued)
5
c
a
b
b
When installing: When attaching the system board to the base cover, adjust the
placement of the wireless radio switch as shown in ꢀaꢁ, and make sure that both
of the audio jack and the microphone jack are attached to the holes on the base
cover as shown in ꢀbꢁ. Improper placement of the switch or those jacks might
cause a damage.
7
7
6
Step
Screw (quantity)
Color
Torque
ꢀ7ꢁ
M2 × 3 mm, wafer-head, nylon-coated (2)
Black
2.0 Nm
(2.5 kgfcm)
82 Lenovo 3000 N500 Hardware Maintenance Manual
Table 27. Removal steps of system board, PC Card/ExpressCard slots assembly (continued)
8
Lenovo 3000 N500 83
Note: Applying labels to the base cover
The new base cover FRU is shipped with a kit containing labels of several kinds.
When you replace the base cover, you need to apply the following label:
ꢀaꢁ
Product label
Following labels need to be peeled off from the old base cover, and need to be
put on the new base cover.
ꢀbꢁ
ꢀcꢁ
ꢀdꢁ
ꢀeꢁ
ꢀfꢁ
Israel label
Serial number label
Compal serial number label
MAC address label
Windows license label (COA)
For some models, you also need to apply one or two FCC labels. Check the old
base cover; if it has one or two FCC labels, find duplicates of them in the label
kit and apply them to the new base cover.
For the location of each label, refer the following figure:
a
b
f
c
e
d
Lenovo 3000 N500 85
Table 32. Removal steps of LCD panel, LCD cable, and hinges (continued)
3
2
4
4
5
5
4
4
Step
Screw (quantity)
Color
Torque
ꢀ4ꢁ
M2 × 3 mm, wafer-head, nylon-coated (8)
Black
1.0 Nm
(1.5 kgfcm)
90 Lenovo 3000 N500 Hardware Maintenance Manual
Table 32. Removal steps of LCD panel, LCD cable, and hinges (continued)
6
7
When installing: Make sure that the LCD cable is attached firmly.
Lenovo 3000 N500 91
2050 Antenna assembly and LCD cover
For access, remove these FRUs in order:
Table 33. Removal steps of antenna assembly and LCD cover
1
1
2
When installing: As you route the cables, make sure that they are not subjected
to any tension. Tension could cause the cables to be damaged by the cable
guides, or a wire to be broken.
92 Lenovo 3000 N500 Hardware Maintenance Manual
Locations
Front view
ꢀ1ꢁ
ꢀ2ꢁ
ꢀ3ꢁ
Integrated camera (for some models)
Touch sensor/volume control buttons
Status indicators
ꢀ4ꢁ
AC power jack
ꢀ5ꢁ
Optical drive
ꢀ6ꢁ
ꢀ7ꢁ
ꢀ8ꢁ
USB (Universal serial bus) connectors
RJ-11 (modem) jack
Stereo speakers
ꢀ9ꢁ
Multi-media reader slot
Stereo headphone jack
Microphone jack
Wireless radio switch
Touch pad buttons
Touch pad
ꢀ10ꢁ
ꢀ11ꢁ
ꢀ12ꢁ
ꢀ13ꢁ
ꢀ14ꢁ
ꢀ15ꢁ
ꢀ16ꢁ
Power button
Lenovo Care button
Lenovo 3000 N500 93
1
16
15
3
14
2
3
8
13
12
11
10
9
8
4
5
6
7
94 Lenovo 3000 N500 Hardware Maintenance Manual
Rear view
ꢀ1ꢁ
ꢀ2ꢁ
ꢀ3ꢁ
ꢀ4ꢁ
ꢀ5ꢁ
PCI Express Card slot
USB (Universal serial bus) connectors
VGA port
RJ-45 (Ethernet) jack
Security key hole
1
2
3
4
5
Bottom view
ꢀ1ꢁ
ꢀ2ꢁ
ꢀ3ꢁ
ꢀ4ꢁ
ꢀ5ꢁ
ꢀ6ꢁ
Battery pack latch (manual)
Battery pack
Battery pack latch (spring loaded)
CPU and DIMM compartment
Hard disk drive compartment
Wireless LAN card compartment
1
2
3
6
4
5
Lenovo 3000 N500 95
Parts list
This section contains following lists of the service parts.
Notes:
v Each FRU is available for all types or models, unless specific types or models
are specified.
v FRU with specific models listed and described as xxU (where U is an example
of a country designator) should be used for all models ending in U.
v FRU with specific models listed and described as 3Dx (where 3D is an
example of a unique configuration) should be used for all of these models,
unless specific country or region designator is specified.
v A CRU (customer replaceable unit) is identified by a single asterisk (*) or two
asterisks (**) in the CRU ID column. An N in the CRU ID column means that
the part is not a CRU. A single asterisk (*) means that the part is a Self-service
CRU; two asterisks (**) means that the part is an Optional-service CRU.
Lenovo 3000 computers contain the following types of CRUs:
Self-service CRUs
These CRUs unplug or are held by no more than two screws.
Examples of these types of CRUs include an AC adapter, a power
cord, a battery, and a hard disk drive. Other Self-service CRUs
depending on product design may include a memory, a wireless card,
a keyboard, and a palm rest with finger print reader and touchpad.
Optional-service CRUs
These CRUs are isolated parts within the computer that are concealed
by an access panel that is typically secured by more than two screws.
Once the access panel is removed, the specific CRU is visible.
v A RoHS compliant FRU is identified by an R. An N in the RoHS ID column
means the part is not a RoHS compliant FRU.
v FRUs marked with ꢀOPꢁ are available as options.
96 Lenovo 3000 N500 Hardware Maintenance Manual
Table 34. Parts list—Overall
No. FRU
FRU no.
RoHS CRU
ID
ID
1
2
3
4
5
6
LCD unit (see “LCD FRUs” on page 101.)
Keyboard cover
43N8371
43N8372
43N8369
43N8376
43N8340
R
R
R
R
R
N
N
N
N
N
Power board with cable
Keyboard bezel assembly with touch pad
LED boards with cable
System board assembly with HDMI, Intel integrated
graphics X4500
v 4233-CTO, 33x, 34x, 35x, 36x, 37x
6
6
System board assembly with HDMI, AMD M86 Hybrid 43N8344
256 MB
v 4233-CTO, 3Dx, 3Ex
R
R
N
N
System board assembly with HDMI, AMD M86GL
Hybrid 512 MB
43N8348
v 4233-CTO, 32x, 38x, 39x, 3Ax, 3Bx, 3Cx
7
7
7
CPU assembly, Intel Celeron M processor575
v 4233-CTO, 32x
42W8034
42W8033
R
R
R
N
N
N
CPU assembly, Intel Celeron M processor585
v 4233-CTO
CPU assembly, Intel Pentium dual-core processor T3200 43N8360
(2.0 GHz)
v 4233-CTO, 33x, 34x, 38x, 39x
7
7
7
7
7
7
7
7
CPU assembly, Intel Pentium dual-core processor T3400 43N8359
(2.16 GHz)
v 4233-CTO, 35x, 36x, 3Ax, 3Bx
R
R
R
R
R
R
R
R
N
N
N
N
N
N
N
N
CPU assembly, Intel Core 2 Duo processor P7350 (2.0
GHz)
v 4233-CTO
42W8032
42W7984
42W7985
42W7986
43N7741
43N8359
43N8352
CPU assembly, Intel Core 2 Duo processor P8400 (2.26
GHz)
v 4233-CTO
CPU assembly, Intel Core 2 Duo processor P8600 (2.40
GHz)
v 4233-CTO
CPU assembly, Intel Core 2 Duo processor P9500 (2.53
GHz)
v 4233-CTO
CPU assembly, Intel Core 2 Duo processor T5670 (1.8
GHz)
v 4233-CTO
CPU assembly, Intel Core 2 Duo processor T5800 (2.0
GHz)
v 4233-CTO
CPU assembly, Intel Core 2 Duo processor T5900 (2.20
GHz)
v 4233-CTO
98 Lenovo 3000 N500 Hardware Maintenance Manual
Table 34. Parts list—Overall (continued)
No. FRU
FRU no.
RoHS CRU
ID
ID
7
7
8
CPU assembly, Intel Core 2 Duo processor T9400 (2.53
GHz)
v 4233-CTO
42W7987
R
N
CPU assembly, Intel Core 2 Duo processor T9600 (2.80
GHz)
v 4233-CTO
42W7988
43N8353
R
R
N
**
1-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card
v 4233-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax,
3Bx, 3Cx, 3Dx, 3Ex
8
9
2-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card
v 4233-CTO
43N8354
42T4581
R
R
**
*
Battery pack, Li-ion (6 cell, 2.4 Ah)
v 4233-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax,
3Bx, 3Cx, 3Dx, 3Ex
9
9
Battery pack, Li-ion (6 cell, 2.4 Ah)
v 4233-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax,
3Bx, 3Cx, 3Dx, 3Ex
42T4583
42T4585
R
R
*
*
Battery pack, Li-ion (6 cell, 2.4 Ah)
v 4233-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax,
3Bx, 3Cx, 3Dx, 3Ex
9
9
9
Battery pack, Li-ion (6 cell, 2.6 Ah)
v 4233-CTO
42T4575
42T4577
42T4579
43N8404
43N8405
43N8406
R
R
R
R
R
R
*
Battery pack, Li-ion (6 cell, 2.6 Ah)
v 4233-CTO
*
Battery pack, Li-ion (6 cell, 2.6 Ah)
v 4233-CTO
*
10 DVD/CD-RW combo drive
**
**
**
v 4233-CTO
10 DVD/CD-RW combo drive
v 4233-CTO
10 DVD-RAM/RW drive
v 4233-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax,
3Bx, 3Cx, 3Dx, 3Ex
10 DVD-RAM/RW drive
43N8407
43N8379
43N8368
R
R
R
**
v 4233-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax,
3Bx, 3Cx, 3Dx, 3Ex
11 Thermal slot cover (UMA)
v 4233-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax,
3Bx, 3Cx
11 Thermal slot cover (discrete)
v 4233-CTO, 3Dx, 3Ex
12 Wireless LAN card slot cover
43N8381
43N8380
43N8389
R
R
R
*
*
*
13 Hard disk drive slot cover
14 SATA Hard disk drive assembly, 120 GB 5,400 rpm
v 4233-CTO
14 SATA Hard disk drive assembly, 120 GB 5,400 rpm
43N8390
R
*
v 4233-CTO
Lenovo 3000 N500 99
Table 34. Parts list—Overall (continued)
No. FRU
FRU no.
43N8391
43N8393
43N8394
43N8395
43N8397
43N8398
43N8399
43N8401
43N8403
RoHS CRU
ID
ID
14 SATA Hard disk drive assembly, 120 GB 5,400 rpm
R
*
v 4233-CTO
14 SATA Hard disk drive assembly, 160 GB 5,400 rpm
R
R
R
R
R
R
R
R
*
*
*
*
*
*
*
*
v 4233-CTO, 32x, 33x, 34x, 35x, 36x, 38x, 39x, 3Ax, 3Bx
14 SATA Hard disk drive assembly, 160 GB 5,400 rpm
v 4233-CTO, 32x, 33x, 34x, 35x, 36x, 38x, 39x, 3Ax, 3Bx
14 SATA Hard disk drive assembly, 160 GB 5,400 rpm
v 4233-CTO, 32x, 33x, 34x, 35x, 36x, 38x, 39x, 3Ax, 3Bx
14 SATA Hard disk drive assembly, 250 GB 5,400 rpm
v 4233-CTO, 37x, 3Cx, 3Dx, 3Ex
14 SATA Hard disk drive assembly, 250 GB 5,400 rpm
v 4233-CTO, 37x, 3Cx, 3Dx, 3Ex
14 SATA Hard disk drive assembly, 250 GB 5,400 rpm
v 4233-CTO, 37x, 3Cx, 3Dx, 3Ex
14 SATA Hard disk drive assembly, 320 GB 5,400 rpm
v 4233-CTO
14 SATA Hard disk drive assembly, 320 GB 5,400 rpm
v 4233-CTO
15 Base cover assembly
43N8370
43N8378
43N8373
R
R
R
N
N
N
16 Speakers
17 Heat sink assembly (integrated)
v 4233-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax,
3Bx, 3Cx
17 Heat sink assembly (discrete)
43N8374
R
N
v 4233-CTO, 3Dx, 3Ex
18 Fan assembly
43N8375
43Y6493
R
R
N
**
19 Intel WiFi Link 5100
v 4233-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax,
3Bx, 3Cx, 3Dx, 3Ex
19 Lenovo 802.11b/g Wireless LAN Mini-PCI Express
43Y6487
43Y6480
R
R
**
**
Adapter
v 4233-CTO
19 Lenovo 802.11b/g Wireless LAN Mini-PCI Express
Adapter
v 4233-CTO
20 Dummy cards
43N8382
43N8377
43Y6491
R
R
R
*
21 ExpressCard slot
N
N
22 Bluetooth daughter card (BDC-2)
—
—
Thermal grease
91P8835
R
N
AC adapter (see “AC adapters” on page 105.)
100 Lenovo 3000 N500 Hardware Maintenance Manual
LCD FRUs
In Lenovo 3000 N500, there are following types of LCDs.
1
2
8
7
3
4
6
5
15.4-in. WXGA TFT
Table 35. Parts list—15.4-in. WXGA TFT
No. FRU
FRU no.
RoHS CRU
ID
ID
1
2
3
LCD front bezel
Hinges
43N8363
43N8364
43N8367
R
N
R
N
Camera module
R
N
v 4233-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax,
3Bx, 3Cx, 3Dx, 3Ex
Lenovo 3000 N500 101
Table 35. Parts list—15.4-in. WXGA TFT (continued)
No. FRU
FRU no.
RoHS CRU
ID
ID
4
RTC cable for camera
43N8366
R
N
v 4233-CTO, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax,
3Bx, 3Cx, 3Dx, 3Ex
5
6
7
7
7
8
8
8
8
LCD cover
43N8362
43N8365
43N8355
43N8356
43N8357
42T0625
42T0627
42T0629
42T0631
R
R
R
R
R
R
R
R
R
N
N
N
N
N
N
N
N
N
LCD cable assembly
Inverter card
Inverter card
Inverter card
LCD panel, 15.4-in. WXGA Glare
LCD panel, 15.4-in. WXGA Glare
LCD panel, 15.4-in. WXGA Glare
LCD panel, 15.4-in. WXGA Glare
102 Lenovo 3000 N500 Hardware Maintenance Manual
Keyboard
Table 36.
Language
P/N
RoHS
ID
CRU
ID
Arabic
42T3353
42T3350
42T3340
—
42T3418
42T3415
—
R
**
Belgian
Canadian French (058)
Canadian French (Acnor)
42T3404
42T3423
42T3412
42T3409
42T3410
42T3408
42T3406
42T3425
42T3420
42T3424
—
Czech
42T3358
42T3347
42T3344
42T3345
42T3343
42T3341
42T3360
42T3355
42T3359
42T3370
42T3348
42T3366
42T3346
42T3356
42T3352
42T3354
42T3362
42T3361
42T3349
42T3351
42T3357
42T3342
42T3338
42T3368
Danish
Dutch
Finnish, Swedish
French
German
Greek (U.S. English and Greek layout)
Hebrew
Hungarian
Icelandic
Italian
42T3413
42T3431
42T3411
42T3421
42T3417
42T3419
42T3427
42T3426
42T3414
42T3416
42T3422
42T3407
42T3403
42T3433
Latin American Spanish
Norwegian
Polish
Portuguese
Russian
Slovak
Slovenian
Spanish
Swiss
Turkish
U.K. English
U.S. English
U.S. English (International, with a Euro
symbol)
Lenovo 3000 N500 103
Miscellaneous parts
Table 37. Parts list—Miscellaneous parts
FRU
P/N
RoHS CRU
ID
ID
Screw kit (including nylon-coated screws):
v M2 × 2.5 mm (black), wafer head (8)
v M2 × 3 mm (black), wafer head (12)
v M2 × 3 mm (silver), wafer head (6)
v M2 × 4 mm (black), wafer head (2)
v M2.5 × 5 mm (black), wafer head (20)
v M2.5 × 5 mm (silver), wafer head (3)
v M2.5 × 8 mm (black), wafer head (14)
v M2.5 × 10 mm (black), wafer head (1)
v M2.5D 5.7+2L K 6.0D (black) (4)
43N8385
R
N
v M3 × 3 mm (silver), wafer head (4)
System miscellaneous parts:
v Optical drive bracket
v HDD bracket
43N8383
43N8384
R
R
N
N
v Foot rubber
v LCD bezel screw rubber
Cable miscellaneous parts:
v (a) Bluetooth cable
v (b) *****
v Microphone cable
v Touch sensor board cable
v Touch pad cable
Note: Italicized letters in parentheses are references to the
exploded view in “Overall” on page 97.
Label kit
43N8386
R
N
104 Lenovo 3000 N500 Hardware Maintenance Manual
AC adapters
Table 38. Parts list—3-pin AC adapters
FRU
P/N
RoHS CRU
ID
ID
3-pin (90 W, 20 V) adapter (models CTO, xxA, xxB, xxC, xxG, 92P1104
xxH, xxK, xxM, xxT, xxV)
R
*
3-pin (90 W, 20 V) adapter (models CTO, xxA, xxB, xxC, xxG, 42T5275
xxH, xxK, xxM, xxT, xxV)
3-pin (90 W, 20 V) adapter (models CTO, xxA, xxB, xxC, xxG, 92P1108
xxH, xxK, xxM, xxT, xxV)
3-pin (65W, 20 V) adapter (models CTO, xxA, xxB, xxC, xxG,
xxH, xxK, xxM, xxT, xxV) ꢀOPꢁ
42T5283
92P1212
92P1157
3-pin (65W, 20 V) adapter (models CTO, xxA, xxB, xxC, xxG,
xxH, xxK, xxM, xxT, xxV)
3-pin (65W, 20 V) adapter (models CTO, xxA, xxB, xxC, xxG,
xxH, xxK, xxM, xxT, xxV)
3-pin (65W, 20 V) adapter (models CTO, xxY)
3-pin (65W, 20 V) adapter (models CTO, xxY)
42T5017
42T5102
Lenovo 3000 N500 105
Power cords
A Lenovo 3000 power cord for a specific country or region is usually available only
in that country or region:
Table 39. Parts list—2-pin power cords
Region
P/N
RoHS CRU
ID
ID
Argentina
v models -CTO, xxY
42T5020
42T5180
42T5008
42T5014
42T5105
42T5183
42T5093
42T5099
R
*
Brazil
v models -CTO, xxP
Canada, U.S.
v models -CTO, xxF, xxL, xxS, xxU
Japan
v models -Exx, Jxx
Table 40. Parts list—3-pin power cords
Region
P/N
RoHS CRU
ID
ID
Australia, New Zealand
v models -CTO, xxG, xxM
42T5050
42T5056
42T5004
42T5065
42T5041
42T5029
42T5083
42T5062
42T5047
42T5077
42T5044
42T5071
42T5035
42T5135
42T5141
42T5089
42T5150
42T5126
42T5114
42T5168
42T5147
42T5132
42T5162
42T5129
42T5156
42T5120
R
*
Bangladesh, Sri Lanka, South Africa
v models -CTO, xxG
Canada, U.S.
v models -CTO, xxF, xxL, xxS, xxU
China (P.R.C.) (other than Hong Kong S.A.R.)
v models -xxC
Denmark
v models -CTO, xxG
European countries
v models -CTO, xxG
India
v models -CTO, xxG
Israel
v models -CTO, xxG
Italy
v models -CTO, xxG
Korea
v models -xxK
Switzerland
v models -CTO, xxG
Taiwan
v models -CTO, xxV
U.K., China (Hong Kong S.A.R.)
v models -CTO, xxB, xxG, xxH
106 Lenovo 3000 N500 Hardware Maintenance Manual
Recovery discs
Windows XP Professional DVDs
For the following models, Windows XP Professional DVDs are prepared:
v 4233-CTO, 24x, 25x, 36x, 3Bx, 3Ex
Table 41. Parts list—Windows XP Professional recovery DVDs
Language
P/N
RoHS CRU
ID
ID
Arabic
56Y0093
56Y0094
56Y0095
56Y0096
56Y0110
56Y0111
56Y0097
56Y0098
56Y0099
56Y0100
56Y0101
56Y0102
56Y0103
56Y0104
56Y0105
56Y0112
56Y0113
56Y0106
56Y0107
56Y0108
56Y0109
R
N
Czech
Danish
Dutch
English
English (modem-disabled)
Finnish
French
German
Greek
Hebrew
Hungarian
Italian
Norwegian
Polish
Russian
Russian (English-enabled)
Slovenian
Spanish
Swedish
Turkish
Lenovo 3000 N500 107
Windows Vista Home Basic (32 bit) DVDs
Windows Vista Home Basic (32 bit) is preinstalled as the operating system in the
following models:
v 4233-CTO, 22x, 32x, 34x, 39x
Table 42. Parts list—Windows Vista Home Basic (32 bit) DVDs
Language
P/N
RoHS CRU
ID
ID
Czech
56Y0024
56Y0025
56Y0040
56Y0042
56Y0026
56Y0027
56Y0028
56Y0029
56Y0030
56Y0031
56Y0032
56Y0033
56Y0035
56Y0034
56Y0043
56Y0044
56Y0041
56Y0037
56Y0036
56Y0038
56Y0039
R
N
Danish
English
English (modem-disabled)
French
German
Greek
Hebrew
Hungarian
Italian
Norwegian
Polish
Romanian
Portuguese
Russian
Russian (English-enabled)
Serbian-Latin
Slovak
Slovenian
Spanish
Turkish
108 Lenovo 3000 N500 Hardware Maintenance Manual
Windows Vista Home Premium (32 bit) DVDs
Windows Vista Home Premium (32 bit) is preinstalled as the operating system in
the following models:
v 4233-CTO, 23x, 35x, 37x, 3Ax, 3Cx, 3Dx
Table 43. Parts list—Windows Vista Home Premium (32 bit) DVDs
Language
P/N
RoHS CRU
ID
ID
Czech
56Y0024
56Y0025
56Y0040
56Y0042
56Y0026
56Y0027
56Y0028
56Y0029
56Y0030
56Y0031
56Y0032
56Y0033
56Y0035
56Y0034
56Y0043
56Y0044
56Y0041
56Y0037
56Y0036
56Y0038
56Y0039
R
N
Danish
English
English (modem-disabled)
French
German
Greek
Hebrew
Hungarian
Italian
Norwegian
Polish
Romanian
Portuguese
Russian
Russian (English-enabled)
Serbian-Latin
Slovak
Slovenian
Spanish
Turkish
Lenovo 3000 N500 109
Windows Vista Business (32 bit) DVDs
Windows Vista Business (32 bit) is preinstalled as the operating system in the
following models:
v 4233-CTO, 24x, 25x, 36x, 3Bx, 3Ex
Table 44. Parts list—Windows Vista Business (32 bit) DVDs
Language
P/N
RoHS CRU
ID
ID
Czech
56Y0000
56Y0001
56Y0016
56Y0018
56Y0002
56Y0003
56Y0004
56Y0005
56Y0006
56Y0007
56Y0008
56Y0009
56Y0011
56Y0010
56Y0019
56Y0020
56Y0017
56Y0013
56Y0012
56Y0014
56Y0015
R
N
Danish
English
English (modem-disabled)
French
German
Greek
Hebrew
Hungarian
Italian
Norwegian
Polish
Romanian
Portuguese
Russian
Russian (English-enabled)
Serbian-Latin
Slovak
Slovenian
Spanish
Turkish
110 Lenovo 3000 N500 Hardware Maintenance Manual
Common service tools
Table 45. Parts list—Common service tools
Tool
P/N
Screwdriver kit
95F3598
1650840
93F2838
00P6967
08K7159
40Y8687
40Y8704
05K9283
27L3452
42W7820
—
1/4″ drive spinner handle
1/4″ Sq. to 1/4″ hex torx adapter
TR7-TR-10 tamper resistant torx bits
Removal tool antenna RF connector
USB 2.0 CD-RW/DVD-ROM combo drive II
USB cable
USB floppy diskette drive for maintenance diskette
USB floppy diskette drive tool kit
Test card for integrated Smart Card
CE Utility Diskette for Lenovo 3000 notebooks
Lenovo 3000 N500 111
112 Lenovo 3000 N500 Hardware Maintenance Manual
Notices
Lenovo may not offer the products, services, or features discussed in this
document in all countries. Consult your local Lenovo representative for
information on the products and services currently available in your area. Any
reference to a Lenovo product, program, or service is not intended to state or
imply that only that Lenovo product, program, or service may be used. Any
functionally equivalent product, program, or service that does not infringe any
Lenovo intellectual property right may be used instead. However, it is the user’s
responsibility to evaluate and verify the operation of any other product, program,
or service.
Lenovo may have patents or pending patent applications covering subject matter
described in this document. The furnishing of this document does not give you
any license to these patents. You can send license inquiries, in writing, to:
Lenovo (United States), Inc.
1009 Think Place - Building One
Morrisville, NC 27560
U.S.A.
Attention: Lenovo Director of Licensing
LENOVO GROUP LTD. PROVIDES THIS PUBLICATION “AS IS” WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some
jurisdictions do not allow disclaimer of express or implied warranties in certain
transactions, therefore, this statement may not apply to you.
This information could include technical inaccuracies or typographical errors.
Changes are periodically made to the information herein; these changes will be
incorporated in new editions of the publication. Lenovo may make improvements
and/or changes in the product(s) and/or the program(s) described in this
publication at any time without notice.
The products described in this document are not intended for use in implantation
or other life support applications where malfunction may result in injury or death
to persons. The information contained in this document does not affect or change
Lenovo product specifications or warranties. Nothing in this document shall
operate as an express or implied license or indemnity under the intellectual
property rights of Lenovo or third parties. All information contained in this
document was obtained in specific environments and is presented as an
illustration. The result obtained in other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it
believes appropriate without incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for
convenience only and do not in any manner serve as an endorsement of those Web
sites. The materials at those Web sites are not part of the materials for this Lenovo
product, and use of those Web sites is at your own risk.
Any performance data contained herein was determined in a controlled
environment. Therefore, the result obtained in other operating environments may
© Copyright Lenovo 2008
113
vary significantly. Some measurements may have been made on development-level
systems and there is no guarantee that these measurements will be the same on
generally available systems. Furthermore, some measurements may have been
estimated through extrapolation. Actual results may vary. Users of this document
should verify the applicable data for their specific environment.
Trademarks
The following terms are trademarks of Lenovo in the United States, other countries
or both:
Lenovo®
Lenovo CareSM
Rescue and Recovery®
ThinkVantage®
The following terms are trademarks of the International Business Machines
Corporation in the United States, other countries, or both:
IBM (used under license)
The following terms are trademarks of Microsoft Corporation in the United States,
other countries, or both:
Windows®
Windows Vista®
The following are trademarks of Intel Corporation or its subsidiaries in the United
States, other countries, or both:
Intel®
Intel® Core™ 2 Duo
Other company, product, or service names may be the trademarks or service marks
of others.
114 Lenovo 3000 N500 Hardware Maintenance Manual
Part Number: 45N3577
(1P) P/N: 45N3577
|
