LavaPort 650
Installation Manual
SSERIAL PCI
P.N. MOKO L74.1
MADE
IN
PN MOKO S-1
MADE IN JAPAN
0255351
CANADA
LAVA COMPUTERS
Rev. B01
Quick Install
Windows 95/98/ME/2000/XP
1. With the power off, insert the LavaPort-650 PCI card into any free PCI
slot.
2. Launch Windows - new hardware will be detected.
3. When prompted, insert the LavaPort-650 installation diskette point
Windows to look at the floppy's root directory.
4. After Windows has booted, click the Start button, then Settings,
Control Panel, System, Device Manager, Ports.The LavaPort-650 port
will be listed as one of your Com Ports. Click“Properties”to change
the default settings as desired.
5a. For Windows 95/98/ME, install the Lava Com Port Redirect and Lava
Modem Speed Set utilities to change the Com numbers of your
ports, and to automate modem speed settings.
5b. For Windows 2000/XP, you can redirect your Com ports by Right
Clicking My Computer > Properties > Hardware > Device Manager >
double click the Lava Port you want to change > Port Settings >
Advanced and under Com Port Number, you can change the port
number from the drop down menu.
3
Hardware Installation
1. Before opening the casing of your computer, make sure that all
power is off.
2. Locate an unused PCI slot and insert the LavaPort-650 into it. Ensure
that it is well seated.
3. Screw the metal backplane of the LavaPort-650 board to your PC’s
casing and replace the machine’s cover.
4. Connect your modem cable to the LavaPort-650 port and turn the
PC on.
Screw for attaching card bracket
to PC casing
Port
PCI Slot
4
Windows Installation
Note: Note: Make sure that you are installing
the correct LavaPort-650
drivers for the appropriate operating system.
DO NOT install NT or Windows 3.x drivers
under Windows95/98/ME/2000/XP
Windows Driver Installation
1. Once the LavaPort-650 is installed in your PC, start your computer.
Windows will automatically detect the LavaPort-650 as a new PCI
Serial Controller and ask you to insert the LavaPort Installation
diskette.The installation files are located in the root directory of this
disk.
2. After the necessary files have been copied,Windows will complete
the full installation of the LavaPort-650. During this process, a new
Com Port will be created in Device Manager under the Ports tree.
The following describes how you may customize this port for your
personal needs.
5
3. Click on the Start button, then choose Settings, Control Panel,
System, Device Manager.You should see a window that is similar to
the following:
6
4. Click on Ports and select the Com port listed under the heading
LavaPort 650 PCI.
5. Click Properties.The following screen will appear:
7
Modifying the Com numbering
and IRQ of your Port
Click on the Resources Tab in the LavaPort 650 listing in Device Manager.
A screen similar to the following will appear:
Because the LavaPort 650 is a PCI device,Windows will always allocate
non-standard I/O resources to this port (e.g. Assigning it as Com 5, even
though any one of Com1-4 may be free). If your software requires the
use of standard I/O resources, you may modify those used by the
LavaPort-650 in one of two ways:
8
1. You may physically modify the I/O Range and IRQ used by the
LavaPort 650 by de-selecting the“Use Automatic Settings”check
box, and double-clicking the appropriate heading, or:
2a. For Windows95/98/ME, you may use the Lava Port Redirect Utility
provided in the Utils subdirectory of your LavaPort diskette.This
utility may be run from the diskette or installed onto your hard drive.
To install the Lava Port Redirect utility on your hard drive, insert the
LavaPort diskette into your floppy drive, click Start, Run and type
A:\Utils\Setup.
The Lava Port Redirect Utility will allow you to change the Com number
assigned to the LavaPort 650 (e.g. Change Com5 to Com 4) without
modifying I/O resources.
2b. For Windows2000/XP, you can change port numbers by Right
Clicking My Computer > Properties > Hardware > Device Manager >
double click the Lava Port you want to change > Port Settings >
Advanced and under Com Port Number, you can change the port
number from the drop down menu.
9
Setting LavaPort Data Rates in Windows
10
The data rate of the LavaPort may be set using the Bits per Second pull
down menu.
Please note that this menu will also appear when setting the“Port
Properties”in any communications application, and may have to be set
independently of your Control Panel settings. Control Panel settings
may not necessarily be linked to those of your Communications
Application. For example, Port speeds in Dial-Up Networking are
controlled independently of speed settings in Device Manager.
For optimum performance, always verify that your LavaPort is set to the
maximum speed supported by your modem, and that all speed settings
are the same in every application.
Please note that the setting of Communications Port Data Rates is often
the most confusing of tasks encountered by modem users. For this
reason, Lava has included the Lava Modem Speed Set utility in the Utils
subdirectory of your LavaPort diskette. Lava strongly recommends using
this utility for all LavaPort-to-modem connections (described later).
11
Lava Modem Speed Set for Windows
The LavaPort-650 supports data rates up to 460.8 kbps, including 115.2
kbps and 230.4 kbps. However, not all modems support Com Port rates
above 115.2 kbps.
If your modem does not support higher data rates and you select a
higher data rate in the LavaPort Properties,Windows will automatically
default to the slowest supported rate in the chain.
Some modems do support higher data rates but require special settings
(AT Commands) and INF files for configuration. Lava has included a
software utility called“Lava Modem Speed Set”which automates these
functions and allows for easy speed reconfiguration.This utility may be
found in the Utils subdirectory of your LavaPort diskette, and is
constantly being updated to support more modems. Please check the
To install the Lava Modem Speed Set utility on your hard drive, insert the
LavaPort diskette into your floppy drive, click Start, Run and type
A:\Utils\Setup.
12
13
Setting LavaPort FIFO Control in Windows
14
The LavaPort-650 uses a 16650 UART incorporating a 32-byte FIFO (first-
in first-out) buffer.
The FIFO control tabs set the buffer“trigger”levels.When the buffer is
filled to its trigger level with the selected number of bytes, the CPU will
be interrupted and asked to either reload the buffer (for transmission),
or retrieve data from the buffer (for reception).
Most efficient data transmission occurs when the CPU is interrupted
infrequently. For each interrupt, the CPU can then service the buffer with
larger data blocks: during transmission, it can place a large burst of data
into the buffer, and during reception it can retrieve a large block from
the buffer and then continue multi-tasking.
Ideally therefore, Receive triggers should be set as high as possible and
Transmit triggers as low as possible.
However, if the Transmit trigger levels are set too low, or Receive triggers
too high, and the CPU is busy when an interrupt is called by the
LavaPort, a short period of inactivity may occur between the port and
the modem.This will reduce effective transmission/reception speeds.
Optimum buffer settings are dependent on your modem speed, your
CPU speed, and the amount of multi-tasking that occurs while online.
For a fast modem and fast CPU performing few multi-tasking functions,
set transmit triggers low and receive triggers high. If multi-tasking while
online, set transmit triggers higher and receive triggers lower.
15
Setting LavaPort Flow Control in Windows
Flow Control refers to the type of signaling that is used between the
modem and the LavaPort.
If you are connecting the LavaPort to a modem or ISDN terminal
adapter, use the default setting of Hardware (RTS/CTS) flow control.
Software Flow Control (Xon/Xoff) is used only for connecting the
LavaPort to a non-modem serial device (e.g. Using a null-modem cable
to connect to another Com Port).
16
Windows NT 4.0 Installation
Note: Make sure that you are installing the correct LavaPort-650
drivers for the appropriate operating system.
DO NOT install Windows 3.x/95/98/Me/2000/XP drivers
under Windows NT
Windows NT Driver Installation
1. Once the LavaPort-650 is installed in your PC, turn your computer on
and start NT.
2. Place the LavaPort installation diskette into your floppy drive and
select Run from the Start Menu.When prompted type:
A:\NT4.0\Setup.
3. After the necessary files have been copied, select My Computer and
start Control Panel. A new icon will appear called“LavaPort”.This
applet should now be used to configure ALL Com Ports in your PC -
not just LavaPorts.
17
Please note that Com 1 may not appear in this applet if you have your
mouse attached to Com 1.
Setting a 230.4 kbps Data Rate
The LavaPort-650 supports data rates up to 460.8 kbps, including 115.2
kbps and 230.4 kbps. However, not all modems support Com Port rates
above 115.2 kbps. If your modem does not support higher data rates
and you select a higher data rate in the LavaPort Properties,Windows
will automatically default to the slowest supported rate in the chain.
Some modems do support higher data rates but require special settings
(AT Commands) and setup files for configuration. Contact your modem
18
This page
intentionally blank
19
Lava
Technical Support
9:00 am to 5:30 pm Monday to Friday (Eastern Time)
Tel: +416 674-5942
Fax: + 416 674-8262
E-mail: [email protected]
Lava Computer MFG Inc.
This device complies with part 15 of the FCC Rules. Operation is subject
to the following conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Lava Computer MFG Inc. 908 Niagara Falls Blvd. #629. North Tonawanda NY 14120-2060
|