Land Pride Conference Phone Fertilizer Spreaders User Manual

Fertilizer Spreaders  
FS500, FS700 & FS1000  
15594  
309-500M  
Operator’s Manual  
Read the Operator’s manual entirely.  
When you see this symbol, the  
subsequent instructions and  
!
warnings are serious - follow without  
exception. Your life and the lives of  
others depend on it!  
6/27/08  
© Copyright 2008 Printed  
Cover photo may show optional  
equipment not supplied with  
standard unit.  
Land Pride  
Important Safety Information  
Important Safety Information  
These are common practices that may or may not be applicable to the products described in  
this manual.  
Keep Riders  
Off Machinery  
Riders obstruct the operator’s  
view. They can be struck by  
foreign objects or thrown from the  
machine.  
Be Aware of Signal Words  
A signal word designates a degree or  
level of hazard seriousness. The  
signal words are:  
!
WARNING  
Indicates a potentially hazardous  
situation which, if not avoided, could  
result in death or serious injury, and  
includes hazards that are exposed  
when guards are removed. It may  
also be used to alert against unsafe  
practices.  
!
DANGER  
Never allow children to operate  
Indicates an imminently hazardous  
situation which, if not avoided, will  
result in death or serious injury. This  
signal word is limited to the most  
extreme situations, typically for  
machine components that, for  
functional purposes, cannot be  
guarded.  
equipment.  
!
CAUTION  
Indicates a potentially hazardous  
situation which, if not avoided, may  
result in minor or moderate injury. It  
may also be used to alert against  
unsafe practices.  
This is the safety alert symbol. It means:  
ATTENTION! BECOME ALERT! YOUR  
SAFETY IS INVOLVED!  
!
For Your Protection  
Shutdown and Storage  
OFF  
Thoroughly read and understand  
the “Safety Label” section, read all  
instructions noted on them.  
Lower machine to ground, turn off  
engine, and remove the key.  
Detach and store implements in a  
area where children normally do  
not play. Secure implement by  
using blocks and supports.  
6/27/08  
FS500, FS700 & FS1000 Fertilizer Spreaders 309-500M  
1
   
Land Pride  
Important Safety Information  
These are common practices that may or may not be applicable to the products described in  
this manual.  
Reduce speed if towed load is not  
Use Safety  
Lights and Devices  
Transport  
Machinery Safely  
equipped with breaks.  
Use the following maximum  
speed - tow load weight ratios as  
a guideline:  
Slow moving tractors, self-  
propelled equipment, and towed  
implements can create a hazard  
when driven on public roads. They  
are difficult to see, especially at  
night.  
Flashing warning lights and turn  
signals are recommended  
whenever driving on public roads.  
Use lights and devices provided  
with implement.  
Comply with state and local laws.  
Maximum transport speed for  
implement is 20 mph. DO NOT  
EXCEED. Never travel at a speed  
which does not allow adequate  
control of steering and stopping.  
Some rough terrains require a  
slower speed.  
20 mph when weight is less than  
or equal to the weight of tractor.  
10 mph when weight is double  
the weight of tractor.  
IMPORTANT: Do not tow a load  
that is more than double the  
weight of tractor.  
Sudden breaking can cause a  
towed load to swerve and upset.  
Use A Safety Chain  
Allow implement to cool  
A safety chain will help control  
drawn machinery should it  
separate from the tractor  
drawbar.  
Use a chain with the strength  
rating equal to or greater than  
the gross weight of the towed  
machinery.  
Attach the chain to the tractor  
drawbar support or other  
specified anchor location. Allow  
only enough slack in the chain to  
permit turning.  
Practice Safe Maintenance  
completely.  
Understand procedure before  
doing work. Use proper tools and  
equipment, refer to Operator’s  
Manual for additional information.  
Do not grease or oil implement  
while it is in operation.  
Inspect all parts. Make sure parts  
are in good condition & installed  
properly.  
Work in a clean dry area.  
Lower the implement to the  
ground, put tractor in park, turn off  
engine, and remove key before  
performing maintenance.  
Remove buildup of grease, oil or  
debris.  
Remove all tools and unused  
parts from implement before  
operation.  
Do not use safety chain for  
towing.  
FS500, FS700 & FS1000 Fertilizer Spreaders 309-500M  
6/27/08  
2
Land Pride  
Important Safety Information  
These are common practices that may or may not be applicable to the products described in  
this manual.  
Avoid High  
Pressure Fluids Hazard  
Escaping fluid under pressure can  
penetrate the skin causing serious  
injury.  
Avoid the hazard by relieving  
pressure before disconnecting  
hydraulic lines.  
Use a piece of paper or  
cardboard, NOT BODY PARTS, to  
check for suspected leaks.  
Wear protective gloves and safety  
glasses or goggles when working  
with hydraulic systems.  
If an accident occurs, see a  
doctor immediately. Any fluid  
injected into the skin must be  
surgically removed within a few  
hours or gangrene may result.  
Wear  
Prepare for Emergencies  
Be prepared if a fire starts.  
Protective Equipment  
Protective clothing and equipment  
Keep a first aid kit and fire  
should be worn.  
extinguisher handy.  
Wear clothing and equipment  
appropriate for the job. Avoid  
loose fitting clothing.  
Prolonged exposure to loud noise  
can cause hearing impairment or  
hearing loss. Wear suitable  
hearing protection such as  
earmuffs or earplugs.  
Operating equipment safely  
requires the full attention of the  
operator. Avoid wearing radio  
headphones while operating  
machinery.  
Keep emergency numbers for  
doctor, ambulance, hospital and  
fire department near phone.  
911  
Safety at All Times  
Thoroughly read and understand the instructions given in this manual before  
operation. Refer to the “Safety Label” section, read all instructions noted on them.  
Operator should be familiar with all functions of the unit.  
Operate implement from the driver’s seat only.  
Do not leave tractor or implement unattended with engine running.  
Dismounting from a moving tractor could cause serious injury or death.  
Do not stand between the tractor and implement during hitching.  
Keep hands, feet, and clothing away from power-driven parts.  
Wear snug fitting clothing to avoid entanglement with moving parts.  
Watch out for wires, trees, etc., when raising implement. Make sure all persons  
are clear of working area.  
Turning tractor too tight may cause implement to ride up on wheels. This could  
result in injury or equipment damage.  
6/27/08  
FS500, FS700 & FS1000 Fertilizer Spreaders 309-500M  
3
Land Pride  
Important Safety Information  
the correct safety labels are included in the request. To  
Safety Labels  
order new labels go to your Land Pride dealer.  
5. Refer to this section for proper label placement.  
To install new labels:  
1. Your fertilizer spreader comes equipped with all safety  
labels in place. They were designed to help you safely  
operate your spreader. Read and follow their directions.  
2. Keep all safety labels clean and legible.  
a. Clean the area the label is to be placed.  
3. Replace all damaged or missing labels. To order new labels  
go to your Land Pride dealer.  
b. Spray soapy water on the surface where the label is to  
be placed.  
4. Some new equipment installed during repair requires safety  
labels to be affixed to the replaced component as specified  
by Land Pride. When ordering new components make sure  
c. Peel backing from label. Press firmly onto the surface.  
d. Squeeze out air bubbles with the edge of a credit card.  
818-541C  
15354  
15354  
15354  
Danger: Toxic Chemical Hazard  
818-542C  
Notice: PTO  
818-539C  
Danger: Thrown Object / Rotating  
Paddles Hazard  
FS500, FS700 & FS1000 Fertilizer Spreaders 309-500M  
6/27/08  
4
Land Pride  
Important Safety Information  
818-540C  
Danger: Guard Missing  
15355  
ROTATING DRIVELINE  
KEEP AWAY!  
818-552C  
Danger: Rotating Driveline  
15355  
6/27/08  
FS500, FS700 & FS1000 Fertilizer Spreaders 309-500M  
5
Land Pride  
Introduction  
Introduction  
Land Pride welcomes you to the growing family of new  
product owners.  
Owner Assistance  
The Warranty Registration card should be filled out by the  
dealer at the time of purchase. This information is  
necessary to provide you with quality customer service.  
This Fertilizer Spreader has been designed with care and  
built by skilled workers using quality materials. Proper  
assembly, maintenance, and safe operating practices will  
help you get years of satisfactory use from this Fertilizer  
Spreader.  
If customer service or repair parts are required contact a  
Land Pride dealer. A dealer has trained personnel, repair  
parts and equipment needed to service the implement.  
The parts on your Fertilizer Spreader have been specially  
designed and should only be replaced with genuine Land  
Pride parts. Therefore, should your Fertilizer Spreader  
require replacement parts go to your Land Pride Dealer.  
Application  
The Land Pride FS500, FS700, and FS1000 are rotary/  
spin type broadcast spreaders designed for Category 1,  
three-point hitch mounting. They are capable of spreading  
seed, sand, salt, top dressings, and prilled/granular  
fertilizer, lime, and iron at delivery rates ranging from  
43-890 lbs. per acre. Each of these models offers specific  
hopper capacities with the FS500 at 350lbs/5.85cu. ft., the  
FS700 at 563lbs/9.38cu. ft., and the FS1000 at 673lbs/  
11.22cu. ft. An internally mounted agitator helps keep  
material in the hopper from bridging. This ensures a  
continuous hopper flow and uniform delivery rate from the  
adjustable pattern rotary spreader.  
Serial Number Plate  
For prompt service always use the serial number and  
model number when ordering parts from your Land Pride  
dealer. Be sure to include your serial and model numbers in  
correspondence also. Refer to Figure 1 for the location of  
your serial number plate.  
The spread rate capability and range of hopper capacities  
make the Land Pride Fertilizer Spreaders well suited for  
applications on farms, golf courses, park systems, athletic  
fields, and large campuses. They also work well for  
smaller municipal or commercial applications of salt and  
sand for snow and ice control. See “Features and  
Benefits”, “Section 6” for additional information.  
Using This Manual  
This Operator’s Manual is designed to help familiarize  
you with safety, assembly, operation, adjustments,  
troubleshooting, and maintenance. Read this manual  
and follow the recommendations to help ensure safe  
and efficient operation.  
Serial Number Plate Location  
15594  
Figure 1  
The information contained within this manual was  
current at the time of printing. Some parts may change  
slightly to assure you of the best performance.  
Further Assistance  
Your dealer wants you to be satisfied with your new  
Fertilizer Spreader. If for any reason you do not  
understand any part of this manual or are not satisfied with  
the service received, the following actions are suggested:  
To order a new Operator’s or Parts Manual contact your  
authorized dealer. Manuals can also be downloaded,  
or printed from the Land Pride Service & Support Center  
by your dealer.  
2. Discuss the matter with your dealership service  
manager making sure he is aware of any problems  
you may have and that he has had the opportunity to  
assist you.  
Terminology  
"Right" or "Left" as used in this manual is determined by  
facing the direction the machine will operate while in use  
unless otherwise stated.  
3. If you are still not satisfied, seek out the owner or  
general manager of the dealership, explain the  
problem and request assistance.  
Definitions  
NOTE: A special point of information that the operator  
must be aware of before continuing.  
4. For further assistance write to:  
Land Pride  
Service Department  
P.O. Box 5060  
IMPORTANT: A special point of information related to  
its preceding topic. Land Pride’s intention is that this  
information should be read and noted before  
continuing.  
Salina, KS 67402-5060  
E-mail address  
FS500, FS700 & FS1000 Fertilizer Spreaders 309-500M  
6/27/08  
6
             
Land Pride  
Section 1: Assembly and Set-up  
Section 1: Assembly and Set-up  
Tractor Requirements  
The frame is designed for mounting on 3-point hitch tractor  
(category 1 or 2).  
Optional Equipment Assemblies  
Agitator  
Assemble the agitator as shown in Figure 1-2.  
Assembly  
The Fertilizer is disassembled when it gets the dealer.  
Refer to Figure 1-1 for assembly.  
Agitator Assembly  
Hook-Up  
Adjust the 3-point hitch so that the distributer disc is  
horizontal and about 27 1/2" - 31 1/2" {70-80 cm} above  
ground level. Refer to Figure 1-3.  
18283  
Assembly  
Figure 1-1  
Spreader Hook-Up  
14827  
Figure 1-3  
6/27/08  
FS500, FS700 & FS1000 Fertilizer Spreaders 309-500M  
7
           
Land Pride  
Section 2: Operation  
Section 2: Operation  
Transporting  
f. Apply multi-purpose grease to inside of outer  
The Fertilizer Spreader is equipped with a towing hook for  
trailers. Maximum towing weight is 1200 pounds.  
(female) driveline section. Assemble driveline and  
install on tractor and spreader. Pull on each  
driveline section to be sure yokes lock into place.  
Make certain driveline shielding is in place and in  
good condition.  
!
CAUTION!  
Never transport your Fertilizer Spreader at speeds in excess of  
20 miles per hour.  
Operating Instructions  
By now you should have properly installed your Land Pride  
Fertilizer Spreader on your tractor. Based on the type of  
material and pounds per acre you intend to broadcast, you  
should have referred to the spreading chart in the  
operator’s manual to determine the proper tractor ground  
speed, distribution gate opening, and spread pattern  
setting for your spreader. This process of taking  
prescribed fertilizer or seed label rates and making the  
necessary spreader setting adjustments is called "initial  
calibration".  
Driveline Installation  
!
DANGER!  
Tractor PTO shield must be in place at all times during  
operation!  
1. Slide driveline end with extended safety cone over  
splined shaft of the gearbox and secure with attaching  
device.  
2. Slide driveline over the tractor’s splined PTO shaft and  
secure with locking device of driveline.  
When setting your spreader up for initial calibration,  
following the chemical or seed supplier’s label directions  
and using the manufacturer’s application rate setting  
charts is "absolutely essential and required". Once you  
have achieved your initial calibration, it is time to make  
"final calibration" adjustments. Measure off an area where  
chemicals or seed are to be applied. An acre is preferred.  
Measure out exactly enough product to cover an acre at  
the manufacturer’s prescribed rate and put it in the hopper.  
You should have already determined the appropriate  
ground speed that will allow you to meet the application  
rate and also maintain 540 rpm PTO speed.  
3. Driveline should now be moved back and forth to  
insure that it is secure on the PTO shaft of the tractor  
and spreader gearbox.  
4. Should the driveline require shortening, Figure 3-3:  
Start the tractor and travel to the one-acre plot you have  
measured off. Maintaining proper ground and engine  
speed, engage the PTO and open the distribution gate just  
as you move onto the plot. Look back often to observe  
your distribution width and pattern density. Typically the  
pattern won’t be as dense on the outer edges. As you  
make your turn for an adjacent pass, adjust your travel  
path to achieve uniform overlap and pattern density. You  
may need to close and open the distribution gate at the  
beginning and ending of each pass. Your hopper should  
empty out just as you complete coverage of your one-acre  
plot. If not, make the necessary adjustments until you are  
absolutely confident that you have achieved the proper  
final calibration.  
Shortening the PTO Shafts  
Figure 3-3  
13588  
a. Raise the tractor 3-point hitch so the input shaft of  
the gearbox is in line with the PTO shaft on the  
tractor. Shut tractor engine off, leaving the  
spresder in position of shortest distance between  
shafts, refer to "A" dimension. Securely block  
spreader in position.  
b. Pull driveline apart as shown in Figure 3-3.  
Reattach outer yoke sections to tractor and  
gearbox. Pull on each driveline section to be sure  
the yokes are locked into place.  
Once you have achieved final calibration, load the  
spreader hopper with the appropriate amount of material  
to be spread. Do not overload hopper with more weight  
than is specified for your individual model. If the tractor  
front end becomes too light for proper steering, add tractor  
weights to the front end. Proceed with spreading  
operations looking back often to ensure a uniform  
distribution pattern and to make sure there are no  
interruptions to hopper flow.  
c. Hold driveline sections parallel to each other to  
determine if too long. Each section should end  
approximately 1" ("B" dimension) short of  
reaching universal joint shield on opposite  
section. If too long, measure 1" ("B" dimension)  
back from universal joint shield and mark on  
opposite section. Do this for both sections.  
With a little practice you should become a very good  
applicator. Once you are done spreading, disengage the  
PTO, park the tractor, set the brake, shut off the tractor,  
and remove the keys. When finished, always clean out the  
spreader to prevent rust and corrosion.  
d. Cut off shield where marked ("X" dimension). Cut  
shaft the same amount ("X" dimension).  
e. Repeat the procedure to the other driveline half.  
Remove all burrs and cuttings.  
FS500, FS700 & FS1000 Fertilizer Spreaders 309-500M  
6/27/08  
8
       
Land Pride  
Section 3: Adjustments  
Section 3: Adjustments  
Adjustments  
How to adjust the Spreader Vanes  
To ensure even distribution on either side of the fertilizer  
spreader of differing specific gravities the vanes can be  
adjusted to the different holes on the distributor disc.  
When all vanes are placed in hole #1, the distribution to  
the left of the tractor driver is increased. If inserted into  
hole #4, distribution to the right of the driver increases.  
Refer to Figure 3-1.  
The fertilizer adjustment depends upon the type of  
material being used and the operator’s experience.  
13611  
Delivery Adjustments  
Figure 3-3  
1. Total width spreading of the fertilizer {A}.  
2. Spreading to the left side driver {B}. Refer to  
Figure 3-2. Remove knob (#3), move down lever  
(#1) to full extent and close the other lock device  
at the same time. This is done by bringing lever  
(#2) to the "1" position.  
3. Spreading to the right side of driver {C}. Refer to  
Figure 3-2. Remove knob (#3), move down lever  
(#2) to full extent and close the other lock device  
at the same time. This is done by bringing lever  
(#1) to the "1" position.  
Hole #1  
Spreader Vanes  
Figure 3-1  
How to adjust the Delivery  
The fertilizer delivery is controlled by properly opening the  
orifices in the hopper bottom through the lock devices op-  
erated by two levers (#1) and (#2). Refer to Figure 3-2.  
Distrubution Gate Settings  
Figure 3-4  
14826  
Lever Adjustments  
Figure 3-2  
13610  
The position of the adjustment levers follows and is shown  
in Figure 3-3.  
6/27/08  
FS500, FS700 & FS1000 Fertilizer Spreaders 309-500M  
9
       
Land Pride  
Section 3: Adjustments  
Spreading Chart for Fertilizer and Seed  
TRACTO SPRED  
R SPEED WIDTH  
QUANTITY SPREAD IN LBS./ACRE AT VARIOUS GATE SETTINGS  
6
1
2
3
4
5
7
8
8.5  
(MPH)  
(FEET)  
635  
2.5  
132  
66  
245  
123  
82  
402  
201  
134  
929  
1014  
507  
1140  
570  
1248  
624  
LARGE  
GRANULAR  
FERTIL-  
IZER  
60  
465  
310  
5.0  
318  
212  
7.5  
44  
338  
380  
416  
925  
463  
309  
2.5  
5.0  
7.5  
311  
156  
104  
448  
224  
149  
709  
355  
237  
1025  
513  
1118  
559  
1182  
591  
MEDIUM  
GRANULAR  
FERTIL-  
IZER  
53  
40  
342  
373  
394  
747  
374  
249  
2.5  
5.0  
7.5  
112  
56  
189  
95  
322  
166  
111  
529  
265  
177  
842  
421  
280  
963  
482  
321  
1051  
526  
FINE  
GRANULAR  
FERTIL-  
IZER  
37  
63  
351  
1236  
618  
2.5  
5.0  
7.5  
226  
113  
75  
368  
184  
123  
560  
280  
187  
890  
445  
297  
1354  
677  
1522  
761  
1632  
816  
CRYSTAL.  
(AMMON.  
23  
20  
SULPHATE)  
412  
451  
507  
544  
THOMAS  
MEAL  
(BASIC  
SLAG)  
1270  
635  
4.0  
8.0  
571  
286  
1685  
843  
46  
35  
28  
23  
20  
17  
3.0  
4.0  
5.0  
6.0  
7.0  
8.0  
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
129  
97  
77  
64  
55  
48  
268  
201  
161  
134  
115  
100  
Wheat  
52  
31  
19  
163  
122  
98  
3.0  
4.0  
5.0  
6.0  
7.0  
8.0  
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
43  
33  
26  
22  
19  
16  
340  
255  
204  
170  
146  
127  
645  
484  
387  
323  
277  
242  
Alfalfa &  
Clover  
82  
70  
61  
0
0
0
0
0
0
3.0  
4.0  
5.0  
6.0  
7.0  
8.0  
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
85  
64  
51  
43  
36  
32  
161  
121  
97  
Fescue &  
Ryegrass  
81  
69  
60  
FS500, FS700 & FS1000 Fertilizer Spreaders 309-500M  
6/27/08  
10  
 
Land Pride  
Section 3: Adjustments  
TRACTO SPRED  
R SPEED WIDTH  
QUANTITY SPREAD IN LBS./ACRE AT VARIOUS GATE SETTINGS  
6
1
2
3
4
5
7
8
8.5  
(MPH)  
(FEET)  
167  
125  
100  
84  
3.0  
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
44  
33  
26  
22  
19  
16  
333  
250  
200  
167  
143  
125  
642  
481  
385  
321  
275  
241  
4.0  
5.0  
Red Clover  
6.0  
31  
72  
7.0  
63  
8.0  
131  
98  
78  
65  
56  
49  
3.0  
4.0  
5.0  
6.0  
7.0  
8.0  
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
30  
23  
18  
15  
13  
11  
311  
233  
186  
155  
133  
116  
660  
495  
396  
330  
283  
248  
Kentucky  
Blue Grass  
& Bermuda  
Grass  
12  
49  
37  
29  
24  
21  
18  
3.0  
4.0  
5.0  
6.0  
7.0  
8.0  
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
131  
98  
79  
66  
56  
49  
271  
203  
163  
136  
116  
102  
Sudan  
Grass  
52  
49  
25  
19  
15  
13  
11  
9
3.0  
4.0  
5.0  
6.0  
7.0  
8.0  
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
81  
61  
49  
41  
35  
30  
186  
139  
111  
93  
Barley  
80  
70  
25  
19  
15  
13  
11  
9
3.0  
4.0  
5.0  
6.0  
7.0  
8.0  
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
81  
61  
49  
41  
35  
30  
186  
139  
111  
93  
Rye  
40  
80  
70  
6/27/08  
FS500, FS700 & FS1000 Fertilizer Spreaders 309-500M  
11  
Land Pride  
Section 4: Maintenance  
implement.  
Section 4: Maintenance  
Proper servicing and adjustment can increase the life of any  
implement. With careful and systematic inspection, you can  
avoid costly maintenance, time and repair.  
General Maintenance  
Prior to operation, thoroughly lubricate fertilizer spreader.  
Check for proper operation of mechanisms by running the  
machine at no-load for a few feet.  
!
Adjust the distributing assembly for spreading the quantity  
desired and recheck for adjustment accuracy.  
CAUTION!  
Be sure to wear proper protective clothing when servicing or  
lubricating your Fertilizer Spreader. Refer to chemical  
manufacturers’ labels for specific clothing requirements.  
All the parts must be cleaned accurately with water after  
every use for a long life and for the efficiency of the  
Lubrication  
Multi-purpose  
spray lube  
Multi-purpose  
grease lube  
Multi-purpose  
oil lube  
Intervals at which  
lubrication is required  
Lubrication  
50  
Legend  
25  
Gearbox  
Type of Lubrication: Use a Lithium Base gun grease, Grade  
2. Note: Grease should be rated for gearbox application.  
Quantity = Grease until visible at purge hole.  
15356  
Seasonally  
Driveline  
Grease all knuckle points daily. This includes the zerks, and  
tubes of the driveline shaft.  
15357  
FS500, FS700 & FS1000 Fertilizer Spreaders 309-500M  
6/27/08  
12  
         
Land Pride  
Section 5: Specifications and Capacities  
Section 5: Specifications and Capacities  
FS500, FS700 & FS1000 Broadcast Spreaders  
FS500  
FS700  
9.38 cu. ft. (563 lbs.)  
44” x 46”  
3’ 4”  
FS1000  
11.22 cu. ft. (673 lbs.)  
46.8” x 46”  
3’ 7”  
Capacity (pounds)  
Overall Dimensions  
Loading Height  
5.85 cu. ft. (350 lbs.)  
37” x 40”  
3’ 3”  
Weight  
118  
128  
139  
3-Point Attachment  
Net Spreadable Granular Width  
PTO Attachment Type  
Transmission Ratio  
Min. Tractor HP  
Category 1  
23’-54’  
Category 1  
23’-54’  
Category 1  
23’-54’  
1 3/8"  
1 3/8"  
1 3/8"  
1:1  
1:1  
1:1  
15 HP  
18 HP  
20 HP  
Range of Spreading  
Possibility (lbs/acre)  
44 - 890  
44 - 890  
44 - 890  
Note: All measurements in British Standard Units are approximate as translated from metric equivalents.  
Specification Drawing  
13613  
Figure 6-1  
6/27/08  
FS500, FS700 & FS1000 Fertilizer Spreaders 309-500M  
13  
 
Land Pride  
Section 6: Features and Benefits  
Section 6: Features and Benefits  
FS500, FS700 & FS1000 Broadcast Spreaders  
Features  
Benefits  
Hopper capacity FS500-350 lbs.; FS700-563 lbs.; FS1000-673 lbs. to meet specific customer needs.  
Spreading capacity Highly productive at 44 to 890 lbs. per acre.  
Spin-type broadcast For even spreading and productive coverage up to 54 ft.  
14 Gauge, one piece steel Seamless for accurate and consistent emptying.  
hopper  
Heavy-duty all steel frame Supports the weight when full.  
Tow hook Handles up to 1200 pounds.  
540 RPM shielded PTO For added safety.  
Plated spinner vanes Protects from corrosive material to enhance longevity.  
Plastic agitator wheel Standard equipment and is useful when spreading powder type materials that tend to  
with steel arm bridge.  
Stainless steel orifice doors Protects from corrosive material enabling doors to operate smoothly.  
Plated adjustment levers Protects from corrosive material to enhance longevity.  
Vinyl cap available Optional vinyl cap with elastic and buckle keeps wind and rain out and material in.  
Cat. 1 3-point hitch For attachment to a wide range of tractors.  
FS500, FS700 & FS1000 Fertilizer Spreaders 309-500M  
6/27/08  
14  
 
Land Pride  
Section 7: Appendix  
Section 7: Appendix  
Torque Values Chart  
Bolt He a d Id e ntific a tion  
Bolt He a d Id e ntific a tion  
5.8  
Class 5.8  
N · m ft-lb  
8.8  
10.9  
Bolt Size  
(Me tric )  
Bolt Size  
(Inc he s)  
Class 8.8  
N · m ft-lb  
Class 10.9  
Grade 2  
Grade 5  
N · m ft-lb  
Grade 8  
N · m ft-lb  
1
2
3
4
in-tpi  
1/4" - 20  
1/4" - 28  
N · m  
7.4  
8.5  
15  
ft-lb  
mm x pitch  
M 5 X 0.8  
M 6 X 1  
N · m  
ft-lb  
5.6  
11  
8
16  
12  
4
7
3
6
5
9
7
6
13  
10  
18  
14  
5
11  
8
15  
11  
5/16" - 18  
5/16" - 24  
3/8" - 16  
3/8" - 24  
7/16" - 14  
7/16" - 20  
1/2" - 13  
1/2" - 20  
9/16" - 12  
9/16" - 18  
5/8" - 11  
5/8" - 18  
3/4" - 10  
3/4" - 16  
7/8" - 9  
11  
24  
17  
33  
25  
M 8 X 1.25 17  
12  
26  
19  
36  
27  
17  
13  
26  
19  
37  
27  
M 8 X 1  
18  
33  
13  
28  
21  
39  
29  
27  
20  
42  
31  
59  
44  
M10 X 1.5  
24  
52  
39  
72  
53  
31  
22  
47  
35  
67  
49  
M10 X 0.75 39  
M12 X 1.75 58  
29  
61  
45  
85  
62  
43  
32  
67  
49  
95  
70  
42  
91  
67  
125  
130  
145  
200  
93  
49  
36  
75  
55  
105  
145  
165  
210  
235  
285  
325  
510  
570  
820  
905  
78  
M12 X 1.5  
M12 X 1  
60  
44  
95  
70  
97  
66  
49  
105  
115  
150  
165  
205  
230  
360  
405  
585  
640  
875  
955  
76  
105  
120  
155  
170  
210  
240  
375  
420  
605  
670  
90  
66  
105  
145  
155  
225  
240  
310  
350  
440  
650  
760  
830  
77  
105  
150  
75  
55  
85  
M14 X 2  
92  
68  
105  
115  
165  
180  
230  
260  
325  
480  
560  
610  
95  
70  
110  
120  
150  
170  
265  
295  
430  
475  
645  
705  
M14 X 1.5  
M16 X 2  
99  
73  
l215 160  
105  
130  
150  
235  
260  
225  
250  
340  
370  
480  
540  
680  
750  
890  
79  
145  
155  
195  
220  
280  
310  
480  
525  
960  
105  
115  
145  
165  
205  
230  
355  
390  
705  
315  
335  
405  
485  
610  
900  
230  
245  
300  
355  
450  
665  
97  
M16 X 1.5  
M18 X 2.5  
M18 X 1.5  
M20 X 2.5  
M20 X 1.5  
M24 X 3  
110  
170  
190  
165  
185  
250  
275  
355  
395  
500  
555  
655  
7/8" - 14  
1" - 8  
1050 780  
1150 845  
1230 910  
1350 995  
1750 1290  
1960 1440  
M24 X 2  
1" - 12  
M30 X 3.5  
M30 X 2  
1510 1120 2100 1550  
1680 1240 2320 1710  
1-1/8" - 7  
1 1/8" - 12  
1 1/4" - 7  
1 1/4" - 12  
1 3/8" - 6  
1 3/8" - 12  
1 1/2" - 6  
1 1/2" - 12  
1080 795  
1210 890  
1060 785  
M36 X 3.5  
M36 X 2  
1730 1270 2650 1950 3660 2700  
1880 1380 2960 2190 4100 3220  
1520 1120 2460 1820  
1680 1240 2730 2010  
1990 1470 3230 2380  
2270 1670 3680 2710  
2640 1950 4290 3160  
2970 2190 4820 3560  
1
in-tpi = nominal thread diameter in inches-threads per  
N· m = newton-meters  
2
3
4
1010 745  
1180 870  
1330 980  
ft-lb= foot pounds  
mm x pitch = nominal thread diameter in millimeters x  
Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above.  
6/27/08  
FS500, FS700 & FS1000 Fertilizer Spreaders 309-500M  
15  
 
Land Pride  
Section 7: Appendix  
Notes  
FS500, FS700 & FS1000 Fertilizer Spreaders 309-500M  
6/27/08  
16  
 
Warranty  
Land Pride warrants to the original purchaser that this Land Pride product will  
be free from defects in material and workmanship beginning on the date of  
purchase by the end user according to the following schedule when used as  
intended and under normal service and conditions for personal use.  
Overall Unit: One year Parts and Labor  
Gearbox and Driveline: One year Parts and Labor  
This Warranty is limited to the replacement of any defective part by Land Pride  
and the installation by the dealer of any such replacement part, and does not cover  
common wear items such as blades, belts, tines, etc. Land Pride reserves the right  
to inspect any equipment or parts which are claimed to have been defective in  
material or workmanship.  
This Warranty does not apply to any part or product which in Land Pride’s  
judgment shall have been misused or damaged by accident or lack of normal  
maintenance or care, or which has been repaired or altered in a way which  
adversely affects its performance or reliability, or which has been used for a  
purpose for which the product is not designed. Misuse also specifically includes  
failure to properly maintain oil levels, grease points, and driveline shafts.  
Claims under this Warranty must be made to the dealer which originally sold  
the product and all warranty adjustments must be made through such dealer. Land  
Pride reserves the right to make changes in materials or design of the product at  
any time without notice.  
This Warranty shall not be interpreted to render Land Pride liable for damages  
of any kind, direct, consequential, or contingent to property. Furthermore, Land  
Pride shall not be liable for damages resulting from any cause beyond its  
reasonable control. This Warranty does not extend to loss of crops, any expense  
or loss for labor, supplies, rental machinery or for any other reason.  
No other warranty of any kind whatsoever, express or implied, is made  
with respect to this sale; and all implied warranties of merchantability and  
fitness for a particular purpose which exceed the obligations set forth in this  
written warranty are hereby disclaimed and excluded from this sale.  
This Warranty is not valid unless registered with Land Pride within 30 days from  
the date of purchase by the end user.  
 
Corporate Office: P.O. Box 5060  
Salina, Kansas 67402-5060 USA  

JVC AV 14JT5EU AV 21JT5EU User Manual
JVC AV 27D800 User Manual
KitchenAid ELECTRIC SLIDE IN 9751596 User Manual
Magnavox 27MDTR10S User Manual
Measurement Specialties PCI 2513 User Manual
NEC CONFERENCE MAX NDA 31109 User Manual
Philips 170S5FS User Manual
Philips BDS4221 User Manual
Philips DECT CD175 User Manual
Philips DVP3588 User Manual