LG Electronics MU 50PZ44MR User Manual

PLASMA MONITOR

OWNER’S MANUAL

MODELS : MU-50PZ44/44M/44V

MU-50PZ44A/44MA/44VA

MU-50PZ44B/44MB/44VB

MU-50PZ44K/44MK/44VK

MU-50PZ44R/44MR/44VR

MU-50PZ44S/44MS/44VS

MU-50PZ90/90M/90V

MU-50PZ90A/90MA/90VA

MU-50PZ90B/90MB/90VB

MU-50PZ90K/90MK/90VK

MU-50PZ90R/90MR/90VR

MU-50PZ90S/90MS/90VS

Please read this owner’s manual thoroughly before operating

the Monitor.

Retain it for future reference.

Record model number and serial number of the Monitor.

See the label attached on the back of the Monitor and relate

this information to your dealer if you ever require service.

Model Number :

Serial Number :

P/NO : 3828VA0410A (RF03GB)

Warning

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to

the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suffi-

cient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of

important operating and maintenance (servicing) instructions in the literature accompanying the appli-

ance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

FCC NOTICE

• A Class B digital device

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

• Any changes or modifications not expressly approved by the party responsible for compli-

ance could void the user’s authority to operate the equipment.

WARNING

TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO

RAIN OR MOISTURE.

Plasma Monitor

Safety Instructions

Important safeguards for you and your new product

Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential elec-

trical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and

observe the following safety points when installing and using your new product, and save them for future reference.

Observing the simple precautions discussed in this booklet can help you get many years of enjoyment and safe operation

that are built into your new product.

This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian StandardsAssociation.

1. Read Instructions

9. Attachments

All the safety and operating instructions should be read

before the product is operated.

Do not use attachments not recommended by the product

manufacturer as they may cause hazards.

2. Follow Instructions

10. Ventilation

All operating and use instructions should be followed.

Slots and openings in the cabinet are provided for ventilation

and to ensure reliable operation of the product and to protect

it from overheating, and these openings must not be blocked

or covered. The openings should never be blocked by plac-

ing the product on a bed, sofa, rug, or other similar surface.

This product should not be placed in a built-in installation

such as a bookcase or rack unless proper ventilation is pro-

vided or the manufacturer’s instructions have been adhered

to.

3. Retain Instructions

The safety and operating instructions should be retained for

future reference.

4. Heed Warnings

All warnings on the product and in the operating instructions

should be adhered to.

5. Cleaning

11. Power Sources

Unplug this product from the wall outlet before cleaning. Do This product should be operated only from the type of power

not use liquid cleaners or aerosol cleaners. Use a damp

cloth for cleaning.

source indicated on the marking label. If you are not sure of

the type of power supply to your home, consult your product

dealer or local power company. For products intended to

operate from battery power, or other sources, refer to the

operating instructions.

6. Water and Moisture

Do not use this product near water, for example, near a bath

tub, wash bowl, kitchen sink, or laundry tub, in a wet base-

ment, or near a swimming pool.

12. Power-Cord Polarization

This product is equipped with a three-wire grounding type

plug, a plug having a third (grounding) pin. This plug will only

7. Accessories, Carts, and Stands

Do not place this product on a slippery or tilted surface, or on fit into the grounding-type power outlet. This is a safety fea-

an unstable cart, stand, tripod, bracket, or table. The product

may slide or fall, causing serious injury to a child or adult,

and serious damage to the product. Use only with a cart,

stand, tripod, bracket, or table recommended by the manu-

facturer, or sold with the product. Any mounting of the prod-

uct should follow the manufacturer’s instructions, and should

use a mounting accessory recommended by the manufac-

turer.

ture. If you are unable to insert the plug into the outlet, con-

tact your electrician to replace your obsolete outlet. Do not

defeat the safety purpose of the grounding-type plug.

13. Power-Cord Protection

Power-supply cords should be routed so that they are not

likely to be walked on or pinched by items placed upon or

against them, paying particular attention to cords at plugs,

convenience receptacles, and the point where they exit from

the product.

8. Transporting Product

A product and cart combination should be moved with care.

Quick stops, excessive force, and uneven surfaces may

cause the product and cart combination to overturn.

PORTABLE CART WARNING

Owner’s Manual

Safety Instructions

Safety Instructions continued

14. Outdoor Antenna Grounding

19. Servicing

If an outside antenna or cable system is connected to the Do not attempt to service this product yourself as opening or

product, be sure the antenna or cable system is grounded so

as to provide some protection against voltage surges and

built-up static charges. Article 810 of the National Electrical

Code (U.S.A.), ANSI/ NFPA 70 provides information with

regard to proper grounding of the mast and supporting struc-

ture, grounding of the lead-in wire to an antenna discharge

removing covers may expose you to dangerous voltage or

other hazards. Refer all servicing to qualified service per-

sonnel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to

unit, size of grounding conductors, location of antenna-dis- qualified service personnel under the following conditions:

charge unit, connection to grounding electrodes, and

requirements for the grounding electrode.

a. If the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into the

product.

Example of Grounding According to National

Electrical Code Instructions

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions as an improper

adjustment of other controls may result in damage and

will often require extensive work by a qualified technician

to restore the product to its normal operation.

e. If the product has been dropped or the cabinet has been

damaged.

Ground Clamp

Antenna Lead in Wire

Antenna Discharge Unit

(NEC Section 810-20)

Grounding Conductor

(NEC Section 810-21)

Electric Service

Equipment

f. If the product exhibits a distinct change in performance.

Ground Clamps

Power Service Grounding

Electrode System (NEC

Art 250, Part H)

21. Replacement Parts

When replacement parts are required, be sure the service

technician has used replacement parts specified by the man-

ufacturer or have the same characteristics as the original

part. Unauthorized substitutions may result in fire, electric

NEC - National Electrical Code

15. Lightning

For added protection for this product (receiver) during a light- shock, or other hazards.

ning storm, or when it is left unattended and unused for long

periods of time, unplug it from the wall outlet and disconnect 22. Safety Check

the antenna or cable system. This will prevent damage to the

product due to lightning and power-line surges.

Upon completion of any service or repairs to this product,

ask the service technician to perform safety checks to deter-

mine that the product is in proper operating condition.

16. Power Lines

An outside antenna system should not be located in the 23. Wall or Ceiling Mounting

vicinity of overhead power lines or other electric light or

The product should be mounted to a wall or ceiling only as

power circuits, or where it can fall into such power lines or recommended by the manufacturer. The product may slide

circuits. When installing an outside antenna system, extreme

care should be taken to keep from touching such power lines

or circuits as contact with them might be fatal.

or fall, causing serious injury to a child or adult, and serious

damage to the product.

24. Heat

17. Overloading

The product should be situated away from heat sources

Do not overload wall outlets and extension cords as this can such as radiators, heat registers, stoves, or other products

result in a risk of fire or electric shock.

(including amplifiers) that produce heat.

18. Object and Liquid Entry

Never push objects of any kind into this product through

openings as they may touch dangerous voltage points or

short-out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the product.

Plasma Monitor

Contents

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4

Screen Menu Options

Auto Adjustment . . . . . . . . . . . . . . . . . . . . . . . .20

Setting Picture Format . . . . . . . . . . . . . . . . . . .20

Picture Size Zoom . . . . . . . . . . . . . . . . . . . . . .20

Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Screen Position . . . . . . . . . . . . . . . . . . . . . . . .21

Manual Configure . . . . . . . . . . . . . . . . . . . . . . .21

Screen Adjustments . . . . . . . . . . . . . . . . . . . . .22

Initializing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Selecting Wide VGA/XGA mode . . . . . . . . . . . .22

Luminance Noise Reduction . . . . . . . . . . . . . . .22

PIP (Picture-in-Picture) Feature

Watching PIP . . . . . . . . . . . . . . . . . . . . . . . . . .23

PIP Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

PIP Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . .23

Swapping PIP . . . . . . . . . . . . . . . . . . . . . . . . . .23

Moving PIP . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Selecting an Input Signal Source for PIP . . . . . .23

Twin Picture Setup Options

Introduction

Controls and Connection Options . . . . . . . . . . . .7

Remote Control Key Functions . . . . . . . . . . . . . .8

Installation

Installation Instruction . . . . . . . . . . . . . . . . . . . .9~10

External Equipment Connections . . . . . . . . . .11~14

VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Cable TV Setup . . . . . . . . . . . . . . . . . . . . . . . .11

External A/V Source Setup . . . . . . . . . . . . . . . .12

DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

DTV Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . .13~14

Operation

Turning on the Monitor . . . . . . . . . . . . . . . . . . . . .15

Menu Language Selection . . . . . . . . . . . . . . . . . .15

Video Menu Options

APC (Auto Picture Control) . . . . . . . . . . . . . . . .16

Manual Picture Control . . . . . . . . . . . . . . . . . . .16

Auto Color Temperature Control . . . . . . . . . . . .16

Manual Color Temperature Control . . . . . . . . . .16

Audio Menu Options

DASP (Digital Auto Sound Processing) . . . . . . .17

Manual Sound Control . . . . . . . . . . . . . . . . . . .17

AVL (Auto Volume Leveler) . . . . . . . . . . . . . . . .17

Time Menu Options

Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .18

On/Off Timer Setup . . . . . . . . . . . . . . . . . . . . .18

Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Special Menu Options

Watching Twin Picture . . . . . . . . . . . . . . . . . . . .24

Sub Picture Size Adjustment . . . . . . . . . . . . . . .24

Swapping the Twin Picture . . . . . . . . . . . . . . . .24

Selecting a Source for the Twin Picture . . . . . . .24

External Control Device Setup . . . . . . . . . . . . . . . .25~30

IR Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31~32

Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . .33

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Key Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

ISM Method . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Low power . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Menu Rotation For Vertical Viewing . . . . . . . . . .19

Setup and Operation Checklist

(See pages 11~13 for available connection and operational setup options.)

1. Unpack Monitor and all accessories.

5. Turn video source equipment on.

2. Connect all external video and audio equipment.

see pages 11 ~ 14.

6. Select viewing source for Monitor.

See page 8.

3 Install batteries in remote control.

See page 8.

7. Fine-tune source image and sound to personal preference

or as required by source.

See pages 16 ~ 17.

4. Turn Monitor on.

See page 15.

8. Additional features Setup

See Contents above.

After reading this manual, keep it handy for future reference.

Owner’s Manual

Introduction

What is a Plasma Display Panel (PDP)?

If voltage is applied to gas within glass panels, ultraviolet rays are produced and fused with a fluorescent substance. At that

instant, light is emitted. A Plasma Display is a next generation flat Display using this phenomenon.

160° - Wide angle range of vision

Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is

clear and visible to viewers anywhere in the room.

Wide Screen

The screen of the Plasma Display is so wide that your viewing experience is as if you are in a theater.

Multimedia

Connect your plasma display to a PC and you can use it for conferencing, games, and internet browsing. The Picture-in-Picture

feature allows you to view your PC and video images simultaneously.

Versatile

The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs would

not fit.

The PDP Manufacturing Process: Why minute colored dots may be present on the PDP screen

The PDP (Plasma Display Panel) which is the display device of this product is composed of 0.9 to 2.2 million cells. A few cell

defects will normally occur in the PDP manufacturing process. Several minute colored dots visible on the screen should be accept-

able. This also occurs in other PDP manufacturers' products and the tiny dots appearing does not mean that this PDP is defective.

Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology is designed

to minimize cell defects during the manufacture and operation of this product.

Cooling Fan Noise

In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the PDP is equipped with

cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operat-

ing and cooling the PDP.

The fan noise doesn't have any negative effect on the PDP's efficiency or reliability. The noise from these fans is normal during the

operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable and is not suffi-

cient cause for the PDP to be exchanged or returned.

Plasma Monitor

Introduction

Controls

Front Panel Controls

- This is a simplified representation of front panel.

Here shown may be somewhat different from your monitor.

ON/OFF

INPUT SELECT

VOL.

E, D Buttons

VOLUME (F,G) Buttons

Main Power Button

INPUT SELECT Button

MENU Button

Remote Control Sensor

Power Standby Indicator

Illuminates red in standby mode,

Illuminates green when the

Monitor is turned on.

Connection Options

Back Connection Panel

- Connection panels shown may be somewhat different from your monitor.

AUDIO L ^(MONO)

AUDIO

(

)

(

)

(

)

(

)

RS-232C INPUT

(CONTROL/SERVICE)

REMOTE

CONTROL

DVI INPUT

RGB INPUT AUDIO INPUT RGB OUTPUT

AUDIO INPUT

COMPONENT INPUT

S-VIDEO

VIDEO INPUT AUDIO INPUT

AC INPUT

EXTERNAL SPEAKER

1. EXTERNAL SPEAKER (8 ohm output)

5. REMOTE CONTROL

Connect to optional external speaker(s).

* For further information, refer to ‘Speaker & Speaker

Connect your wired remote control to the remote control

port on the Monitor.

Stand’ manual.

6. COMPONENT INPUT/AUDIO INPUT JACKS

2. RS-232C INPUT (CONTROL/SERVICE) PORT

Connect a component video/audio device to these jacks.

Connect to the RS-232C port on a PC.

7. S-VIDEO INPUTS

3. DVI (Digital Visual Interface) INPUT/

RGB INPUT/AUDIO INPUT JACKS

Connect the monitor output connector from a PC to the

appropriate input port.

Connect S-Video out from an S-VIDEO VCR to the S-VIDEO

input.

AUDIO/VIDEO INPUT JACKS

Connect audio/video out from external equipment to these

jacks.

4. RGB OUTPUT PORT

You can watch the RGB signal on another monitor, connect

RGB OUTPUT to another monitor’s PC input port.

8. POWER CORD SOCKET

This Monitor operates on an AC power. The voltage is indi-

cated on the Specifications page. Never attempt to operate

the Monitor on DC power.

Owner’s Manual

Introduction

Remote Control Key Functions

- When using the remote control, aim it at the remote control sensor on the monitor.

- Under certain conditions such as if the remote IR signal is interrupted, the remote control may not function. Press

the key again as necessary.

POWER

Switches the Monitor between

INPUT SELECT

Selects source: Video, S-Video,

ON and STANDBY.

SLEEP

Sets the Sleep Timer.

(Refer to p.18)

RGB, DVI, or Component mode.

POWER

SLEEP

DASP

INPUT SELECT

To select the sound appropriate to

your viewing program character:

Flat, Music, Cinema, Sports, or

User (Refer to p.17)

APC

Adjusts the factory preset picture

according to the room.

APC

ARC

DASP

PIP ARC

(Refer to p.16)

PIP

TWIN PICTURE

SUB INPUT

MUTE

PIP ARC

Changes the PIP picture format.

(Refer to p.23)

ARC

Changes the picture format.

(Refer to p.20)

SWAP

TWIN PICTURE

(Refer to p.24)

PIP

Switches the sub picture on or off.

(Refer to p.23)

VOL

SUB INPUT

Selects the input source for the sub

picture.

SWAP

Exchanges main and sub picture

images. (Refer to p.23, 24)

MUTE

Switches the sound on or off.

Displays on screen menus one by one.

Exits the current menu.

D / E

Selects menu option.

NUMBER buttons

Memorizes menu changes.

F / G (Volume button)

Increases/decreases sound level.

Adjusts menu settings.

WIN. SIZE

Adjusts the sub picture size.

POWER

REW

STOP

PLAY

P/STILL

WIN.POSITION

REC

Moves the sub picture.

VCR BUTTONS

Control some video cassette

recorders.

WIN.SIZE WIN.POSITION SPLIT ZOOM

SPLIT ZOOM

ZOOM -

ZOOM +

Enlarges the picture.

ZOOM-/ZOOM+

Enlarges or reduces

the main picture size.

Installing Batteries

• Open the battery compartment cover on the back side and

insert the batteries with correct polarity.

• Install two 1.5V batteries of AAA type. Don’t mix used batteries

with new batteries.

Plasma Monitor

Installation

Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer

where you purchased the product.

POWER

SLEEP

INPUT SELECT

APC

ARC

DASP

PIP ARC

PIP

TWIN PICTURE

SUB INPUT

MUTE

SWAP

VOL

POWER

REW

STOP

PLAY

P/STILL

1.5V

REC

WIN.SIZE WIN.POSITION SPLIT ZOOM

ZOOM

Owner’s Manual

Batteries

BNC-RCA Adapter

Remote Control

D-sub 15 pin Cable

Power Cord

DVI-D Cable

Installation Instructions

• The Monitor can be installed in various ways such as on a wall, or on a desktop etc.

• The plasma display is designed to be mounted horizontally or vertically. The speakers shown are optional.

GROUNDING

Power

Supply

Ensure that you connect the grounding / earth wire to prevent possible

electric shock. If grounding methods are not possible, have a qualified

electrician install a separate circuit breaker. Do not try to ground the

Short-circuit

Breaker

unit by connecting it to telephone wires, lightening rods, or gas pipes.

Wall Mount: Horizontal installation

For proper ventilation, allow a clearance of 4” on each

side and 2” from the wall. Detailed installation instruc-

tions are available from your dealer, see the optional

Wall Mounting Bracket Installation and Setup Guide.

inches

4 inches

Owner’s Manual

Installation

Installation Instructions continued

Desktop Pedestal Installation

For proper ventilation, allow a clearance of 4” on each

side and the top, 2.36” on the bottom, and 2” from the

wall. Detailed installation instructions are included in the

optional Desktop Stand Installation and Setup Guide

available from your dealer.

4 inches

inches

4 inches

2.36 inches

Wall Mount: Vertical installation (MU-50PZ44M/44V/90M/90V series models only)

Detailed installation instructions are included in the

optional Vertical Wall Mounting Bracket Installation and

Setup Guide available from your dealer.

NOTE: When installing the monitor vertically, the front

panel controls must be in the left side position.

When installing the monitor vertically, you

have to change the OSD display mode so

that the menus will appear correctly and also

to protect the monitor from overheating

(Refer to P. 19).

10 Plasma Monitor

Installation

External Equipment Connections

NOTE: Not all cables shown are included with the plasma display.

VCR Setup

- To avoid picture noise (interference), leave an adequate distance between the VCR and Monitor

- Use the ISM Method feature to avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still

picture from a VCR. If the 4:3 picture format is used; the fixed image may remain visible on the screen.

How to connect

1. Connect the provided BNC-RCA adapter to the monitor’s VIDEO

INPUT.

2. Connect the audio and video cables from the VCR's output jacks to

the monitor input jacks, as shown in the figure.

AUDIO L ^(MONO)

AUDIO

When connecting the monitor to VCR, match the jack colors (Video

= yellow, Audio Left = white, and Audio Right = red).

AUDIO INPUT COMPONENT INPUT

S-VIDEO VIDEO INPUT AUDIO INPUT

Mono VCR: Connect the video output cable from the VCR to the

VIDEO input on the monitor.

S-VIDEO VCR: Connect the S-Video output cable from the VCR to

the S-VIDEO input on the monitor. (Note that S-Video offers higher

quality).

How to use

1. Insert a video tape into the VCR and press PLAY on the VCR.

(Refer to the VCR owner’s manual.)

2. Use the INPUT SELECT button on the remote control to select

Video.

(If connected to S-VIDEO, select the S-Video input source.)

S-VIDEO

OUT

VCR

(R) AUDIO (L)

VIDEO

Cable TV Setup

- After subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV programming.

The monitor cannot display TV programming unless a TV tuner device or cable TV converter box is connected to the Monitor.

- For further information regarding cable TV service, contact your local cable TV service provider(s).

How to connect

1. Connect the provided BNC-RCA adapter to the monitor’s VIDEO

INPUT.

2. Connect the audio and video cables from the Cable Box's output

jacks to the monitor input jacks, as shown in the figure.

When connecting the monitor to a Cable Box, match the jack colors

AUDIO L ^(MONO)

AUDIO

(Video = yellow, Audio Left = white, and Audio Right = red).

AUDIO INPUT

COMPONENT INPUT

S-VIDEO VIDEO INPUT AUDIO INPUT

How to use

1. Use the INPUT SELECT button on the remote control to select

Video.

2. Select your desired channel with the remote control for cable box.

(R) AUDIO (L) VIDEO

VCR

Cable

Cable Box

Owner’s Manual 11

Installation

External A/V Source Setup

How to connect

1. Connect the provided BNC-RCA adapter to the monitor’s

VIDEO INPUT.

AUDIO L ^(MONO)

2. Connect the audio and video cables from the external

equipment's output jacks to the monitor input jacks, as

shown in the figure.

AUDIO

AUDIO INPUT

S-VIDEO VIDEO INPUT AUDIO INPUT

COMPONENT INPUT

When connecting the monitor to external equipment, match

the jack colors (Video = yellow, Audio Left = white, and

Audio Right = red).

Camcorder

How to use

1. Use the INPUT SELECT button on the remote control to

select Video.

Video Game Set

2. Operate the corresponding external equipment. Refer to

external equipment operating guide.

AUDIO

VIDEO

DVD Setup

How to connect

1. Connect the DVD video outputs to the COMPONENT (Y, PB, PR)

INPUT jacks and connect the DVD audio outputs to the AUDIO

INPUT jacks on the monitor, as shown in the figure.

AUDIO L ^(MONO)

AUDIO

2. If your DVD only has an S-Video output jack, connect this to the

S-VIDEO input on the monitor and connect the DVD audio outputs

to the AUDIO INPUT jacks on the monitor, as shown in the figure.

AUDIO INPUT COMPONENT INPUT

S-VIDEO VIDEO INPUT AUDIO INPUT

How to use

1. Turn on the DVD player, insert a DVD.

2. Use the INPUT SELECT button on the remote control to select

Component. (If connected to S-VIDEO, select the S-Video exter-

nal input source.)

3. Refer to the DVD player's manual for operating instructions.

• Component Input ports

To get better picture quality, connect a DVD player to the compo-

nent input ports as shown below.

(R) AUDIO (L)

S-VIDEO

DVD

Component ports of the

Monitor

R-Y

B-Y

Video output ports

of DVD player

DTV Setup

- To watch digitally broadcast programs, purchase and

connect a digital set-top box.

- This monitor supports HDCP (High-bandwidth Digital

Contents Protection) protocol for DVI DTV

(480p,720p,1080i) mode.

AUDIO L ^(MONO)

AUDIO

REMOTE

CONTROL

DVI INPUT

RGB INPUT AUDIO INPUT RGB OUTPUT

AUDIO INPUT

COMPONENT INPUT

S-VIDEO

VIDEO INPUT AUDIO INPUT

How to connect

Use the monitor’s COMPONENT (Y, PB, PR) INPUT,

RGB or DVI jack for video connections, depending on

your set-top box connector. Then, make the corre-

sponding audio connections.

How to use

1. Turn on the digital set-top box. (Refer to the owner’s

manual for the digital set-top box.)

2. Use INPUT SELECT on the remote control to select

Component, RGB, or DVI.

(R) AUDIO (L)

RGB-DTV OUTPUT

(R) AUDIO (L)

DVI-DTV OUTPUT

Digital Set-top Box

12 Plasma Monitor

Installation

PC Setup

- This monitor provides Plug and Play capability, meaning that the PC adjusts automatically to its settings. The monitor sends

configuration information (EDID) to the PC using the Video Electronics Standard Association (VESA) Display Data Channel

(DDC) protocol.

- The monitor perceives 640x480, 60Hz as DTV 480p based on the PC graphic card. In this case, change the screen scanning

rate for the graphic card.

How to connect

1. To get the best picture quality, adjust the PC

graphics card to a 1024x768, 60Hz. Resolutions

(

)

(

)

(

)

(

)

over UXGA cannot be displayed.

RS-232C INPUT

(CONTROL/SERVICE)

REMOTE

CONTROL

2. Use the monitor’s RGB INPUT or DVI (Digital

Visual Interface) INPUT port for video connections,

depending on your PC connector.

RGB INPUT

DVI INPUT

AUDIO INPUT RGB OUTPUT

EXTERNAL SPEAKER

If the graphic card on the PC does not output ana-

log and digital RGB simultaneously, connect only

one of either RGB INPUT or DVI INPUT to display

the PC on the monitor.

If the graphic card on the PC does output analog

and digital RGB simultaneously, set the monitor to

either RGB or DVI; (the other mode is set to Plug

and Play automatically by the monitor.)

3. Then, make the corresponding audio connections.

If using a sound card, adjust the PC sound as

required.

How to use

1. Turn on the PC and the monitor.

2. Turn on the display by pressing the POWER button on the monitor's remote control.

3. Use the INPUT SELECT button on the remote control to select RGB or DVI.

4. Check the image on your monitor. There may be noise associated with the resolution, vertical pattern, contrast or

brightness in PC mode. If noise is present, change the PC mode to another resolution, change the refresh rate to

another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC

graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.

NOTES: • Depending on the graphics card, DOS mode may not work if you use a DVI-I cable.

• Avoid keeping a fixed image on the monitor's screen for a long period of time. The fixed image may become

permanently imprinted on the screen. Use the Orbiter screen saver when possible.

• The synchronization input form for Horizontal and Vertical frequencies is separate.

Owner’s Manual 13

Installation

Monitor Display Specifications (RGB-PC / DVI-PC Mode)

Horizontal

Vertical

Horizontal

Vertical

Resolution

Frequency(KHz) Frequency(Hz)

31.468

37.861

31.469

37.927

31.469

35.000

37.861

37.500

43.269

35.156

37.879

46.875

53.674

49.725

31.500

35.000

37.500

70.09

85.08

70.08

85.03

59.94

66.66

72.80

75.00

85.00

56.25

60.31

75.00

85.06

74.55

60.00

70.00

75.00

60.00

70.00

75.00

60.00

70.06

75.02

60.05

70.01

75.00

60.00

60.02

60.00

75.02

60.00

75.02

31.500

35.000

37.500

48.363

56.476

60.023

54.348

63.995

67.500

60.000

63.981

47.700

59.625

47.700

59.625

640x350

852x480

720x400

1024x768

1152x864

640x480

1280x960

1280x1024

800x600

1360x768

1366x768

832x624

848x480

14 Plasma Monitor

Operation

Turning on the Monitor

Turning on the Monitor just after installation

1. Connect power cord correctly.

2. Press the

ON/OFF button on the Monitor. At this moment, the Monitor is switched to standby

mode. Press the INPUT SELECT button on the Monitor or press the POWER, INPUT SELECT

button on the remote control and then the Monitor will switch on.

Turning on the Monitor (power cord is still connected)

1. If the Monitor was turned off with the

ON/OFF button on the Monitor

• Press the ON/OFF button on the Monitor to turn the Monitor on.

2. If the Monitor was turned off with the remote control and then the

ON/OFF button on the Monitor

• Press the ON/OFF button on the Monitor and then press the INPUT SELECT button on the

Monitor or press the POWER, INPUT SELECT button on the remote control to turn the Monitor on.

Menu Language Selection

- The menus can be shown on the screen in the selected language. First select your language.

1. Press the MENU button and then use _D

button to select the SPECIAL menu.

VIDEO

AUDIO

TIME

Language

English

Key lock

2. Press the G button and then use _D

button to select Language.

Español

Português

Français

ISM Method

Low power

Set ID.

3. Press the G button and then use _{D E}button to select your desired language.

From this point on, the on-screen menus will be shown in the language of your choice.

OSD Rotate

SPECIAL

SCREEN

TWIN

4. Press the OK button to save.

Prev.

Owner’s Manual 15

Operation

Video Menu Options

- Video menu adjustment are unique to each input source. Readjust Video menu settings for each following

input source as preferred.

• RGB (PC) / DVI (PC),

• RGB (DTV) / DVI (DTV) / Component (480p, 720p, 1080i)

• Video / S-Video / Component (480i)

APC (Auto Picture Control)

- APC adjusts the Monitor for the best picture appearance.

- When adjusting Video menu options (contrast, brightness, color, sharpness, and tint) manually, APC automatically

changes to User.

1. Press the APC button repeatedly to select the picture appearance setup option as shown below.

Clear

Optimum

Soft

User

• You can also adjust APC in the VIDEO menu.

•

Clear, Optimum, and Soft settings are preset for optimum picture quality at the factory and cannot be changed.

Manual Picture Control (User option)

- You can adjust picture contrast, brightness, color, sharpness, and tint to the levels you prefer.

VIDEO

AUDIO

TIME

APC

1. Press the MENU button and then use _{D / E}button to select the VIDEO menu.

ACC

Color temp.

2. Press the ^Gbutton and then use

button to select the desired picture option

/ E

Contrast

85 G

Brightness

Color

(Contrast, Brightness, Color, Sharpness, or Tint).

3. Press the ^Gbutton and then use F / G button to make appropriate adjustments.

4. Press the OK button to save.

SPECIAL

Sharpness

Tint

SCREEN

TWIN

MENU Prev.

Auto Color Temperature Control

- To initialize values (reset to default settings), select the Normal option.

- When adjusting color temperature options (red, green, and blue) manually, ACC automatically changes to User.

1. Press the MENU button and then use _{D / E}button to select the VIDEO menu.

VIDEO

AUDIO

TIME

APC

ACC

Normal

Cool

2. Press the ^Gbutton and then use _{D / E}button to select ACC .

Color temp.

Contrast

Brightness

Color

Warm

User

3. Press the ^Gbutton and then use _{D / E}button to select either Normal (Default), Cool

(Preset), Warm (Preset), or User (Manual Adjustment).

SPECIAL

Sharpness

Tint

SCREEN

TWIN

4. Press the OK button to save.

MENU Prev.

Manual Color Temperature Control (User option)

- You can adjust red, green, and blue to any color temperature you prefer.

1. Press the MENU button and then use _{D / E}button to select the VIDEO menu.

VIDEO

AUDIO

TIME

APC

ACC

2. Press the ^Gbutton and then use _{D / E}button to select the Color temp .

Color temp.

Red

Contrast

Brightness

Color

Green

Blue

3. Press the ^Gbutton and then use _{D / E}button to select Red, Green, or Blue.

SPECIAL

Sharpness

Tint

4. Use the ^F/ G button to make appropriate adjustments.

SCREEN

TWIN

• The adjustment range for Red, Green, and Blue is -20 ~ +20.

MENU Prev.

5. Press the OK button to save.

16 Plasma Monitor

Operation

Audio Menu Options

DASP (Digital Auto Sound Processing)

- DASP lets you enjoy the best sound without any special adjustment because the Monitor has the appropriate

sound options based on the program content.

- When adjusting sound options (treble, bass, and balance) manually, DASP automatically changes to User.

1. Press the DASP button repeatedly to select the appropriate sound setup as shown below.

Flat

Music

Cinema

Sports

User

• You can also adjust DASP in the AUDIO menu.

•

Flat, Music, Cinema and Sports are preset for good sound quality at the factory and cannot be

changed.

Manual Sound Control (User option)

DASP

AVL

VIDEO

AUDIO

TIME

1. Press the MENU button and then use _{D / E}button to select the AUDIO menu.

Balance

2. Press the ^Gbutton and then use

button to select the desired sound option

/ E

Treble

Bass

50 G

(Balance, Treble, or Bass).

SPECIAL

3. Press the G button and then use F / G button to make appropriate adjustments.

SCREEN

TWIN

4. Press the OK button to save.

MENU Prev.

AVL (Auto Volume Leveler)

- This feature maintains an equal volume level; even if you change channels.

VIDEO

AUDIO

TIME

1. Press the MENU button and then use _{D / E}button to select the AUDIO menu.

DASP

AVL

Off

2. Press the ^Gbutton and then use _{D / E}button to select AV L .

Balance

Treble

Bass

3. Press the ^Gbutton and then use _{D / E}button to select On or Off.

SPECIAL

4. Press the OK button to save.

SCREEN

TWIN

MENU Prev.

Owner’s Manual 17

Operation

Time Menu Options

Clock Setup

- If current time setting is wrong, reset the clock.

1. Press the MENU button and then use _{D / E}button to select the TIME menu.

2. Press the G button and then use _{D / E}button to select Clock.

3. Press the ^Gbutton and then use _{D / E}button to set the hour.

VIDEO

AUDIO

TIME

Clock

Off timer

On timer

Auto off

SPECIAL

4. Press the ^Gbutton and then use _{D / E}button to set the minutes.

SCREEN

TWIN

5. Press the OK button to save.

MENU Prev.

On/Off Timer Setup

- Timer function operates only if current time has been already set.

- Off-Timer function overrides On-Timer function if they are set to the same time.

1. Press the MENU button and then use _{D / E}button to select the TIME menu.

VIDEO

AUDIO

TIME

Clock

2. Press the ^Gbutton and then use _{D / E}button to select Off timer or On timer.

Off timer

On timer

Auto off

Off

3. Press the G button and then use _{D / E}button to select On.

• To cancel On/Off timer function, select Off.

SPECIAL

Vol.

SCREEN

TWIN

4. Press the G button and then use _{D / E}button to set the hour.

MENU Prev.

5. Press the ^Gbutton and then use _{D / E}button to set the minutes.

6. For only On timer function; Press the G button and then use _{D / E}button to set

volume level.

7. Press the OK button to save.

Auto Off

- If there is no input signal, the Monitor turns off automatically after 10 minutes.

1. Press the MENU button and then use _{D / E}button to select the TIME menu.

VIDEO

AUDIO

TIME

Clock

Off timer

On timer

2. Press the G button and then use _{D / E}button to select Auto off.

Auto off

Off

3. Press the ^Gbutton and then use _{D / E}button to select On or Off.

SPECIAL

4. Press the OK button to save.

SCREEN

TWIN

MENU Prev.

Sleep Timer

- The sleep timer turns the Monitor off at a preset time. Note that this setting is cleared when the monitor is turned off.

1. Press the SLEEP button repeatedly to select the number of minutes. First the

^z--- Min option appears on the

screen, followed by the following sleep timer options: 10, 20, 30, 60, 90, 120, 180, and 240 minutes.

2. When the number of minutes you want is displayed on the screen, press the OK button. The timer begins to count

down from the number of minutes selected.

3. To check the remaining minutes before the monitor turns off, press the SLEEP or OK button once.

4. To cancel the Sleep Timer, press the SLEEP button repeatedly until

^z--- Min appears.

18 Plasma Monitor

Operation

Special Menu Options

Key Lock

- The monitor can be set up so that it can only be used with the remote control.

- This feature can be used to prevent unauthorized viewing by disabling the front panel controls.

- This Monitor is programmed to remember which option it was last set to even if you turn the monitor off.

1. Press the MENU button and then use _{D / E}button to select the SPECIAL menu.

VIDEO

Language

Key lock

Off

AUDIO

2. Press the G button and then use _{D / E}button to select Key lock.

ISM Method

Low power

Set ID.

TIME

3. Press the G button and then use _{D / E}button to select On or Off.

OSD Rotate

SPECIAL

• When you select On, the display ‘

on the front panel is pressed.

Key lock’ appears on the screen if any button

SCREEN

TWIN

Prev.

4. Press the OK button to save.

-In setting Key lock ‘On’, if the monitor is turned off with the remote control, press the INPUT SELECT button

on the monitor or POWER, INPUT SELECT on the remote control to turn the monitor on.

ISM (Image Sticking Minimization) Method

- A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in an ghost

image remaining; even when you change the image. Avoid allowing a fixed image to remain on the Monitor's

screen for a long period of time.

VIDEO

Language

1. Press the MENU button and then use _{D / E}button to select the SPECIAL menu.

Key lock

AUDIO

TIME

Normal

ISM Method

2. Press the ^Gbutton and then use _{D / E}button to select ISM Method.

White wash

Orbiter

Low power

Set ID.

Inversion

SPECIAL

OSD Rotate

3. Press the G button and then use _{D / E}button to select either Normal, White wash,

Orbiter, or Inversion.

SCREEN

TWIN

• Normal

Prev.

If image sticking is never a problem, ISM is not necessary - set to Normal.

• White wash

White Wash removes permanent images from the screen. Note: An excessive permanent image may be impossible to clear

entirely with White Wash. To return to normal viewing, press the any button.

• Orbiter

Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid

a permanent image on the screen, the image will move every 1 minutes: Right → Right → Downside → Downside → Left

→ Left → Upside → Upside.

• Inversion

Inversion will automatically invert the plasma display panel color every 30 minutes.

4. Press the OK button to save.

Low Power

VIDEO

- Low power reduces the plasma display's power consumption.

Language

AUDIO

TIME

Key lock

ISM Method

1. Press the MENU button and then use _{D / E}button to select the SPECIAL menu.

2. Press the ^Gbutton and then use _{D / E}button to select Low power.

3. Press the G button and then use _{D / E}button to select On or Off.

Low power

Off

Set ID.

SPECIAL

OSD Rotate

SCREEN

TWIN

Prev.

• When you select On, the screen darkens.

4. Press the OK button to save.

Menu Rotation for Vertical Viewing (MU-50PZ44M/44V/90M/90V series models only)

VIDEO

1. Press the MENU button and then use the _{D / E}button to select the SPECIAL menu.

Language

Key lock

AUDIO

2. Press the G button and then use the _{D / E}button to select OSD Rotate.

ISM Method

Low power

Set ID.

TIME

3. Press the G button and then use the _{D / E}button to select Normal or Rotate.

• Select Normal, if the monitor was installed horizontally.

• Select Rotate, if the monitor was installed vertically.

SPECIAL

OSD Rotate

Normal

Rotate

SCREEN

TWIN

Prev.

4. Press the OK button to save.

Owner’s Manual 19

Operation

Screen Menu Options

Auto Adjustment

- RGB (PC) mode only; This function doesn’t work for RGB-DTV.

- Automatically adjusts picture position and minimizes image shaking.

- After adjustment, if the image is still not correct, your Monitor is functioning properly but needs further adjustment.

- The Auto config. and Manual config. are not active in DVI mode.

1. Press the MENU button and then use _{D / E}button to select the SCREEN menu.

VIDEO

Auto config.

ARC

To set

AUDIO

2. Press the G button and then use _{D / E}button to select Auto config..

Zoom in/out

Position

TIME

Manual config.

3. Press the G button to run Auto configure.

Screen adj.

SPECIAL

Reset

• When Auto config. has finished, OK will be shown on screen.

• If the position of the image is still not correct, try Auto adjustment again.

XGA Mode

SCREEN

TWIN

MENU Prev.

4. In RGB (PC) mode, if the image needs to be adjusted more after using Auto config.,

you can make further adjustments with the Manual config. option.

Setting Picture Format

- Caution: If a 4:3 fixed image is on the screen for a long time, it may remain visible.

- Set every aspect ratio for RGB 480p, DVI 480p, Component 480i/480p, Video, and S-Video sources.

- Use 4:3, or 16:9 for other input sources.

1. Press the ARC button repeatedly to select the desired picture format. You can also adjust ARC in the SCREEN

menu.

• 4:3

- Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with black bars appearing at both

the left and right sides.

• 16:9

- Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen.

• Horizon

- Choose Horizon when you want to adjust the picture in a non-linear proportion, that is, more enlarged at both

sides, to create a spectacular view.

• Zoom

- Choose Zoom when you want to view the picture without any alteration. However, the top and bottom portions

of the picture will be cropped.

Picture Size Zoom

- When enlarging or reducing the picture, the image may become distorted.

1. Use ZOOM+/ZOOM- button to enlarge or reduce the picture size.

• Zoom adjustment range is 100~300.

2. Adjust the main picture position using the _{D / E}/ F / ^Gbuttons while in enlarged picture mode.

Zoom out

100%

20 Plasma Monitor

Operation

Split Zoom

- Enlarges the picture in correct proportions.

- Split Zoom can be used for all input sources.

- In 2-Split Zoom mode, you can only move the image up or down.

- If a screen is enlarged, a screen can move without selecting section of screen Split Zoom.

- It’s not available to use this function if OSD Rotate is set to the Rotate option.

1. Press the SPLIT ZOOM button repeatedly to select either 2, 4 , or 9 Split Zoom.

9-Split zoom

4-Split zoom

2-Split zoom

▲

▼

▲

▼

▲

▼

◀

▶

◀

▶

◀

▶

2. Press the number button corresponding to the section you wish to enlarge. You can move within the enlarged

image with the _{D / E}/ F / G button. To return to normal viewing, press the SPLIT ZOOM button again.

Section 5 is enlarged to fill

the screen.

Example of choosing 5.

9-Split zoom

▲

▼

◀

▶

Screen Position

- This function works in the following mode:

RGB-PC, RGB-DTV (480p,720p,1080i), COMPONENT (480p,720p,1080i).

1. Press the MENU button and then use _{D / E}button to select the SCREEN menu.

VIDEO

AUDIO

TIME

Auto config.

ARC

2. Press the ^Gbutton and then use _{D / E}button to select Position.

3. Press the ^Gbutton and then use _{D / E}/ F / G button to adjust the position.

4. Press the OK button to save.

Zoom in/out

▲

Position

◀

▶

▼

Manual config.

Screen adj.

Reset

SPECIAL

SCREEN

TWIN

XGA Mode

MENU Prev.

Manual Configure (RGB-PC mode only)

- If the image still isn’t clear after auto adjustment and especially if characters are still jittery, adjust the picture

Phase manually.

- To correct the screen size, adjust Clock.

1. Press the MENU button and then use _{D / E}button to select the SCREEN menu.

VIDEO

Auto config.

2. Press the G button and then use _{D / E}button to select Manual config..

3. Press the G button and then use _{D / E}button to to select Phase or Clock.

4. Use the F / G button to make appropriate adjustments.

AUDIO

TIME

ARC

Zoom in/out

Position

Manual config.

Phase

Clock

SPECIAL

Screen adj.

Reset

SCREEN

TWIN

XGA Mode

• The Phase adjustment range is 0 ~ 31.

• The Clock adjustment range is -50 ~ +50.

MENU Prev.

5. Press the OK button to save.

Owner’s Manual 21

Operation

Screen Menu Options continued

Screen Adjustments (Video, S-Video and Component 480i mode only)

- Use this function to correct jittering or picture instability while viewing a video tape.

1. Press the MENU button and then use _{D / E}button to select the SCREEN menu.

2. Press the G button and then use _{D / E}button to select Screen adj..

3. Press the G button and then use _{D / E}button to to select TV or VCR.

VIDEO

AUDIO

TIME

Auto config.

ARC

Zoom in/out

Position

Manual config.

SPECIAL

Screen adj.

• Select the VCR option if watching a VCR.

• Select the TV option for other equipment.(Except VCR)

VCR

Reset

YNR

SCREEN

TWIN

MENU Prev.

4. Press the OK button to save.

Initializing (Reset to original factory value)

- This function operates in every mode.

- To initialize the adjusted value

VIDEO

AUDIO

TIME

1. Press the MENU button and then use _{D / E}button to select the SCREEN menu.

2. Press the G button and then use _{D / E}button to select Reset.

3. Press the G button.

Auto config.

ARC

Zoom in/out

Position

Manual config.

Screen adj.

SPECIAL

• You can initialize Zoom In/Out, Manual config., Position, Split zoom, PIP size, PIP posi-

tion and sub picture size for twin picture.

To set

Reset

SCREEN

TWIN

XGA Mode

MENU Prev.

Selecting Wide VGA/XGA mode (RGB-PC, DVI-PC mode only)

- To see a normal picture, match the resolution of RGB XGA mode (1024x768, 1360x768, 1366x768) with the selection for XGA

mode and the resolution of RGB VGA mode (640x480, 848x480, 852x480) with the selection for VGA mode in the SCREEN

menu.

- If the input source is RGB VGA mode, the screen menu option is changed from XGA mode to VGA mode automatically.

VIDEO

1. Press the MENU button and then use _{D / E}button to select the SCREEN menu.

AUDIO

Auto config.

2. Press the G button and then use _{D / E}button to select VGA mode/XGA mode.

ARC

TIME

Zoom in/out

3. Press the G button and then use _{D / E}button to select the desired VGA/XGA resolution.

Position

SPECIAL

SCREEN

TWIN

Manual config.

Screen adj.

Reset

1024x768

1360x768

1366x768

4. Press the OK button to save.

XGA Mode

MENU Prev.

Luminance Noise Reduction (Video, S-Video and Component 480i modes only)

- Use YNR to reduce the picture noise which may appear on the screen.

VIDEO

AUDIO

TIME

1. Press the MENU button and then use _{D / E}button to select the SCREEN menu.

Auto config.

ARC

2. Press the G button and then use _{D / E}button to select YNR.

Zoom in/out

Position

3. Press the G button and then use _{D / E}button to select On or Off.

SPECIAL

Manual config.

Screen adj.

Reset

4. Press the OK button to save.

Off

SCREEN

TWIN

YNR

MENU Prev.

22 Plasma Monitor

Operation

PIP (Picture-In-Picture) Feature

- PIP lets you view 2 different inputs (sources) on your monitor screen at the same time. One source will be large, and the

other source will show a smaller inset image.

PIP Size

Watching PIP

Press the WIN.SIZE button and then use F / G button to

Press the PIP button repeatedly to turn PIP on or off.

change the sub picture size.

Component

Video

10 : 30

Win.size

PIP Aspect Ratio

Swapping the PIP

Press the PIP ARC button. The sub picture appears as shown.

Press the SWAP button to switch the main and sub pictures.

Component

Video

Component

10 : 30

16 :

4 :

Main Picture

Sub Picture

Moving the PIP

Press the WIN.POSITION button.

Press the _{D / E}/ F / G button repeatedly until desired posi-

tion is achieved. The sub picture moves up/down/left/right.

Win.position

▲

◀

▶

▼

Selecting an Input Signal Source for the PIP

Use the SUB INPUT button to select the input source for

the sub picture.

Available Sub Picture Sources

Main Picture Source

Video

S-Video, Component 480i/480p/720p/1080i, RGB, and DVI

Video, Component 480i/480p/720p/1080i, RGB, and DVI

Video,S-Video, RGB, and DVI

Video and S-Video

Component 480i, Video, and S-Video

S-Video

Component 480i

Component 480p/720p/1080i

RGB and DVI

Owner’s Manual 23

Operation

Twin Picture Setup Option

- As the name suggests, this mode splits the screen into 2, allowing 2 picture sources to be shown on the monitor screen at the

same time. Each source is given half the screen.

Watching Twin Picture

Press the TWIN PICTURE button repeatedly to select one of the Twin Picture options.

DW 1

DW 2

Sub Picture Size Adjustment

Press the WIN.SIZE button and then use F / G button to change the sub picture size.

• Using the WIN.SIZE function in Twin Picture mode, main and sub picture sizes are

changed simultaneously.

Using the WIN.SIZE function in PIP mode, sub picture size is changed.

• WIN.POSITION is not functional in Twin Picture mode.

Win.size

◀

▶

Swapping the Twin Picture

Use the SWAP button to switch the main and sub pictures in twin picture mode.

Component

Video

Component

10 : 30

Main Picture

Sub Picture

Selecting a Source for the Twin Picture

Use the SUB INPUT button to select the input source for the sub picture.

Available Sub Picture Sources

Main Picture Source

Video

S-Video, Component 480i/480p/720p/1080i, RGB, and DVI

Video, Component 480i/480p/720p/1080i, RGB, and DVI

Video,S-Video, RGB, and DVI

Video and S-Video

Component 480i, Video, and S-Video

S-Video

Component 480i

Component 480p/720p/1080i

RGB and DVI

24 Plasma Monitor

External Control Device Setup

- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system)

and control the Monitor’s functions externally.

- Connect the serial port of the control device to the RS-232C jack on the Monitor back panel.

- RS-232C connection cables are not supplied with the Monitor.

AUDIO L ^(MONO)

AUDIO

(

)

(

)

(

)

(

)

RS-232C INPUT

(CONTROL/SERVICE)

REMOTE

CONTROL

DVI INPUT

RGB INPUT AUDIO INPUT RGB OUTPUT

AUDIO INPUT

COMPONENT INPUT

S-VIDEO

VIDEO INPUT AUDIO INPUT

AC INPUT

EXTERNAL SPEAKER

Type of Connector: D-Sub 9-pin Male

No. Pin Name

No Connection

RXD (Receive data)

TXD (Transmit data)

DTR (DTE side ready)

GND

DSR (DCE side ready)

RTS (Ready to send)

CTS (Clear to send)

No Connection

RS-232C Configurations

3- Wire Configuration

(Not standard)

7-Wire Configuration

(Standard RS-232C cable)

PDP

TXD

RXD

GND

DTR

DSR

RTS

CTS

RXD

TXD

GND

DTR

DSR

RTS

CTS

TXD

RXD

GND

DSR

DTR

CTS

RTS

RXD

TXD

GND

DTR

DSR

RTS

CTS

D-Sub 9

Owner’s Manual 25

External Control Device Setup

Set ID

- Use this function to specify a monitor ID number.

- Refer to ‘Real Data Mapping 1’. See page 27.

1. Press the MENU button and then use the _{D / E}button to select the SPECIAL menu.

VIDEO

AUDIO

TIME

Language

Key lock

2. Press the G button and then use _{D / E}button to select Set ID..

ISM Method

Low power

3. Press the G button and then use F / G button to adjust Set ID. to choose the desired

monitor ID number.

Set ID.

SPECIAL

OSD Rotate

SCREEN

TWIN

• The adjustment range of Set ID. is 1 ~ 99.

Prev.

Communication Parameters

• Baud rate : 115200 bps (UART)

• Data length : 8 bits

• Stop bit : 1 bit

• Communication code : ASCII code

• Parity : None

Command Reference List

Transmission / Receiving Protocol

COMMAND 1 COMMAND 2

DATA

(Hexadecimal)

Transmission

[Command1][Command2][ ][Set ID][ ][Data][Cr]

01. Power

0 ~ 1

02. Input Select

03. Aspect Ratio

04. Screen Mute

05. Volume Mute

06. Volume Control

07. Contrast

0 ~ 4

[Command 1]: k, j

[Command 2]: To control PDP set.

0 ~ 3

[Set ID]: You can adjust the set ID to choose desired moni-

tor ID number in Special menu. Adjustment range

is 1 ~ 99. When selecting Set ID ‘0’, every con-

nected PDP set is controlled. Set ID is indicated

as decimal (1~99) on menu and as Hexa decimal

(0x0~0x63) on transmission/receiving protocol.

[DATA]: To transmit command data.

0 ~ 1

0 ~ 64

0 ~ 1

08. Brightness

09. Color

10. Tint

Transmit ‘FF’ data to read status of command.

[Cr]: Carriage Return

11. Sharpness

ASCII code ‘0x0D’

12. OSD Select

13. Remote Control Lock Mode

14. PIP/Twin

[

]: ASCII code ‘space (0x20)’

0 ~ 1

0 ~ 3

15. PIP Aspect Ratio

16. Split Zoom

0 ~ 1

21 ~99

0 ~ 3

OK Acknowledgement

17. PIP Position

18. Treble

[Command2][ ][Set ID][ ][OK][Data][x]

0 ~ 64

0 ~ 3

* The Monitor transmits ACK (acknowledgement) based on

this format when receiving normal data. At this time, if the

data is data read mode, it indicates present status data. If

the data is data write mode, it returns the data of the PC

computer.

19. Bass

20. Balance

21. Color Temperature

22. Red Adjustment

23. Green Adjustment

24. Blue Adjustment

25. PIP Input Source

26. Abnormal State

27. ISM Method

28. Low Power

0 ~ C8

0 ~ 4

Error Acknowledgement

[Command2][ ][Set ID][ ][NG][x]

0 ~ a

0 ~ 3

* The Monitor transmits ACK (acknowledgement) based on

this format when receiving abnormal data from

non-viable functions or communication errors.

0 ~ 1

29. Orbiter Time Setting

30. Orbiter Pixel Setting

31. Picture Size Setting

for Twin Picture mode

32. Auto Configure

1 ~ FE

0 ~9

Data 1: Illegal Code

2: Not supported function

3: Wait more time

0 ~64

• Menu doesn’t display on screen when setting the 4,

12, 13, and 26 ~ 32.

26 Plasma Monitor

External Control Device Setup

04. Screen Mute (Command2:d)

01. Power (Command2:a)

G To control Power On/Off of the Monitor.

Transmission

GTo select screen mute on/off.

Transmission

[k][a][ ][Set ID][ ][Data][Cr]

[k][d][ ][Set ID][ ][Data][Cr]

Data 0 : Power Off

1 : Power On

Data 0 : Screen mute off (Picture on)

1 : Screen mute on (Picture off)

Acknowledgement

[a][ ][Set ID][ ][OK][Data][x]

[d][ ][Set ID][ ][OK][Data][x]

GTo show Power On/Off.

Transmission

05. Volume Mute (Command2:e)

[k][a][ ][Set ID][ ][FF][Cr]

GTo control volume mute on/off.

You can also adjust mute using the MUTE button on

remote control.

Data 0 : Power Off

1 : Power On

Acknowledgement

Transmission

[a][ ][Set ID][ ][OK][Data][x]

[k][e][ ][Set ID][ ][Data][Cr]

* In a like manner, if other functions transmit ‘FF’ data

based on this format, Acknowledgement data feedback

presents status about each function.

Data 0 : Volume mute on (Volume off)

1 : Volume mute off (Volume on)

Acknowledgement

[e][ ][Set ID][ ][OK][Data][x]

02. Input Select (Command2:b) (Main Picture Input)

G To select input source for the Monitor.

06. Volume Control (Command2:f)

You can also select an input source using the INPUT

GTo adjust volume.

SELECT button on the Monitor's remote control.

You can also adjust volume with the volume buttons

on remote control.

Transmission

[k][b][ ][Set ID][ ][Data][Cr]

Transmission

Data 0 : RGB

1 : Component

3 : S-video

4 : DVI

[k][f][ ][Set ID][ ][Data][Cr]

Data Min : 0 ~ Max : 64

2 : Video

• ^{Refer to ‘Real data mapping1’ as shown below.}

Acknowledgement

[b][ ][Set ID][ ][OK][Data][x]

[f][ ][Set ID][ ][OK][Data][x]

07. Contrast (Command2:g)

03. Aspect Ratio (Command2:c) (Main picture format)

G To adjust screen contrast.

GTo adjust the screen format.

You can also adjust contrast in the Video menu.

You can also adjust the screen format using the ARC

(Aspect Ratio Control) button on remote control or in the

Special menu.

Transmission

[k][g][ ][Set ID][ ][Data][Cr]

Transmission

Data Min : 0 ~ Max : 64

[k][c][ ][Set ID][ ][Data][Cr]

• Refer to ‘Real data mapping1’ as shown below.

Acknowledgement

Data 0 : Wide screen (16:9)

1 : Normal screen (4:3)

2 : Full screen (Zoom)

3 : Horizon

[g][ ][Set ID][ ][OK][Data][x]

Acknowledgement

Real data mapping 1

[c][ ][Set ID][ ][OK][Data][x]

0 : Step 0

* You select either 16:9 or 4:3 screen aspect ratio using the

PC, DTV 720p/1080i.

A : Step 10 (SET ID 10)

F : Step 15 (SET ID 15)

10 : Step 16 (SET ID 16)

64 : Step 100

Owner’s Manual 27

External Control Device Setup

08. Brightness (Command2:h)

13. Remote Control Lock Mode (Command2:m)

G To adjust screen brightness.

G To lock the remote control and front panel controls on the

You can also adjust brightness in the Video menu.

monitor

Transmission

[k][h][ ][Set ID][ ][Data][Cr]

[k][m][ ][Set ID][ ][Data][Cr]

Data Min : 0 ~ Max : 64

Data 0: Lock off

1: Lock on

• Refer to ‘Real data mapping 1’. See page 27.

Acknowledgement

[m][ ][Set ID][ ][OK][Data][x]

[h][ ][Set ID][ ][OK][Data][x]

• If you’re not using the remote control and front panel con-

trols on the monitor, use this mode. When main power is

on/off, remote control lock is released.

09. Color (Command2:i)

GTo adjust the screen color.

14. PIP / Twin (Command2:n)

You can also adjust color in the Video menu.

G To control the PIP (Picture-in-Picture) or Twin Picture.

You can also control the PIP/Twin picture mode using the PIP

or TWIN PICTURE button on the remote control or in the

Twin menu.

Transmission

[k][i][ ][Set ID][ ][Data][Cr]

Data Min : 0 ~ Max : 64

Transmission

• Refer to ‘Real data mapping 1’. See page 27.

Acknowledgement

[k][n][ ][Set ID][ ][Data][Cr]

Data 0: PIP/DW off

1: PIP

2: DW1

3: DW2

[i][ ][Set ID][ ][OK][Data][x]

Acknowledgement

[n][ ][Set ID][ ][OK][Data][x]

10. Tint (Command2:j)

GTo adjust the screen tint.

You can also adjust tint in the Video menu.

15. PIP Aspect Ratio (Command2:o)

G To select the PIP picture format.

You can also select the PIP picture format using PIP ARC

on the remote control.

Transmission

[k][j][ ][Set ID][ ][Data][Cr]

Data Red : 0 ~ Green : 64

Transmission

• ^{Refer to ‘Real data mapping 1’. See page 27.}

[k][o][ ][Set ID][ ][Data][Cr]

Acknowledgement

Data 0: 4:3

1: 16:9

[j][ ][Set ID][ ][OK][Data][x]

Acknowledgement

[o][ ][Set ID][ ][OK][Data][x]

11. Sharpness (Command2:k)

16. Split Zoom (Command2:p)

GTo adjust the screen sharpness.

GTo operate split zoom function and select the split

You can also adjust sharpness in the Video menu.

zoom section number.

Transmission

[k][k][ ][Set ID][ ][Data][Cr]

[k][p][ ][Set ID][ ][Data][Cr]

Data Min: 0 ~ Max: 64

Data Min: 21 ~ Max: 99

• Refer to ‘Real data mapping 1’. See page 27.

Acknowledgement

• Refer to ‘Real data mapping 2’.

Acknowledgement

[k][ ][Set ID][ ][OK][Data][x]

[p][ ][Set ID][ ][OK][Data][x]

12. OSD Select (Command2:l)

GTo select OSD (On Screen Display) on/off.

Transmission

Real data mapping 2

21: Selection 1 of 2 split zoom

24: Selection 4 of 2 split zoom

41: Selection 1 of 4 split zoom

42: Selection 2 of 4 split zoom

44: Selection 4 of 4 split zoom

45: Selection 5 of 4 split zoom

91: Selection 1 of 9 split zoom

[k][l][ ][Set ID][ ][Data][Cr]

Data 0: OSD off

1: OSD on

Acknowledgement

[l][ ][Set ID][ ][OK][Data][x]

99: Selection 9 of 9 split zoom

28 Plasma Monitor

External Control Device Setup

17. PIP Position (Command2:q)

21. Color Temperature (Command2:u)

GTo adjust color temperature.

G To select sub picture position for PIP.

You can also adjust ACC in the Video menu.

You can also adjust the sub picture position using

Win.position on the remote control or in the Twin menu.

Transmission

[k][u][ ][Set ID][ ][Data][Cr]

Data 0: Normal 1: Cool 2: Warm 3: User

[k][q][ ][Set ID][ ][Data][Cr]

Data 0: Right down on screen

1: Left down on screen

2: Left up on screen

Acknowledgement

[u][ ][Set ID][ ][OK][Data][x]

3: Right up on screen

Acknowledgement

[q][ ][Set ID][ ][OK][Data][x]

22. Red Adjustment (Command2:v)

GTo adjust red in color temperature.

Transmission

18. Treble (Command2:r)

[k][v][ ][Set ID][ ][Data][Cr]

GTo adjust treble.

Data Min: 0 ~ Max: C8

You can also adjust treble in the Audio menu.

• Refer to ‘Real data mapping 3’ as shown below.

Acknowledgement

Transmission

[k][r][ ][Set ID][ ][Data][Cr]

[v][ ][Set ID][ ][OK][Data][x]

Data Min: 0 ~ Max: 64

• Refer to ‘Real data mapping 1’. See page 27.

Acknowledgement

23. Green Adjustment (Command2:w)

[r][ ][Set ID][ ][OK][Data][x]

GTo adjust green in color temperature.

Transmission

[k][w][ ][Set ID][ ][Data][Cr]

19. Bass (Command2:s)

Data Min: 0 ~ Max: C8

GTo adjust bass.

• Refer to ‘Real data mapping 3’ as shown below.

You can also adjust bass in the Audio menu.

Acknowledgement

Transmission

[w][ ][Set ID][ ][OK][Data][x]

[k][s][ ][Set ID][ ][Data][Cr]

Data Min: 0 ~ Max: 64

• Refer to ‘Real data mapping 1’. See page 27.

Acknowledgement

24. Blue Adjustment (Command2:$)

GTo adjust blue in color temperature.

Transmission

[s][ ][Set ID][ ][OK][Data][x]

[k][$][ ][Set ID][ ][Data][Cr]

Data Min: 0 ~ Max: C8

20. Balance (Command2:t)

• Refer to ‘Real data mapping 3’ as shown below.

Acknowledgement

GTo adjust balance.

You can also adjust balance in the Audio menu.

[$][ ][Set ID][ ][OK][Data][x]

Transmission

Real data mapping 3

[k][t][ ][Set ID][ ][Data][Cr]

0 : -20

5 : -19

A : -18

Data Min: 0 ~ Max: 64

• Refer to ‘Real data mapping 1’. See page 27.

Acknowledgement

[t][ ][Set ID][ ][OK][Data][x]

5F: -1

64: 0

69: +1

C3: +19

C8: +20

Owner’s Manual 29

External Control Device Setup

25. PIP Input Select (Command2:y)

29. Orbiter Time Setting (Command2:r)

GTo adjust orbiter operation time term.

G To select input source for sub picture in PIP mode.

Transmission

[j][r][ ][Set ID][ ][Data][Cr]

Data Min: 1 ~ Max: FE

[k][y][ ][Set ID][ ][Data][Cr]

Data 0: RGB

2: Video

1: Component

3: S-video

4: DVI

Acknowledgement

[r][ ][Set ID][ ][OK][Data][x]

[y][ ][Set ID][ ][OK][Data][x]

26. Abnormal State (Command2:z)

30. Orbiter Pixel Setting (Command2:s)

GTo recognize an abnormal state.

GTo adjust pixel number in orbiter function.

Transmission

[k][z][ ][Set ID][ ][FF][Cr]

Data FF:Read

[j][s][ ][Set ID][ ][Data][Cr]

Data Min: 0 ~ Max: 9

Acknowledgement

[z][ ][Set ID][ ][OK][Data][x]

[s][ ][Set ID][ ][OK][Data][x]

Data 0: Normal (Power on and signal exist)

1: No signal (Power on)

2: Turn the monitor off by remote control

3: Turn the monitor off by sleep time function

4: Turn the monitor off by RS-232C function

5: 5V down

31. Picture Size Setting for Twin Picture mode

(Command2:t)

GTo adjust main picture size in twin picture mode.

6: AC down

Transmission

7: Turn the monitor off by Fan Alarm function

8: Turn the monitor off by off time function

9: Turn the monitor off by auto off function

a: Turn the monitor off by AV board detect

[j][t][ ][Set ID][ ][Data][Cr]

Data Min: 0 ~ Max: 64

• ^{Refer to ‘Real data mapping1’. See page 27.}

Acknowledgement

27. ISM Method (Command2:p)

[t][ ][Set ID][ ][OK][Data][x]

GTo avoid having a fixed image remain on screen.

Transmission

[j][p][ ][Set ID][ ][Data][Cr]

32. Auto Configure (Command2:u)

Data 0: Normal

1: White wash

2: Orbiter

3: Inversion

GTo adjust picture position and minimize image shaking

automatically. Auto Configure only works in RGB-PC

mode.

Acknowledgement

Transmission

[p][ ][Set ID][ ][OK][Data][x]

[j][u][ ][Set ID][ ][Data][Cr]

Data 1: To set

28. Low Power (Command2:q)

Acknowledgement

GTo control the low power function on/off.

Transmission

[u][ ][Set ID][ ][OK][Data][x]

[j][q][ ][Set ID][ ][Data][Cr]

Data 0: Low power off

1: Low power on

Acknowledgement

[q][ ][Set ID][ ][OK][Data][x]

30 Plasma Monitor

IR Code

How to Connect

Connect your wired remote control to the Remote Control port on the Monitor.

Remote Control IR Code

G Output waveform

Single pulse, modulated with 37.917KHz signal at 455KHz

T^C

Carrier frequency

F^CAR= 1/TC = fOSC/12

Duty ratio = T1/T^C= 1/3

G Configuration of frame

• 1st frame

Lead

code

Low

custom code

High

custom code

Data code

C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7

• Repeat frame

Repeat code

T^f

G Lead code

9 ms

4.5 ms

0.55 ms

G Repeat code

9 ms

2.25 ms

G Bit description

• Bit “0”

• Bit “1”

0.56 ms

1.12 ms

0.56 ms

2.24 ms

G Frame interval : Tf

The waveform is transmitted as long as a key is depressed.

Tf=108ms @455KHz

Owner’s Manual 31

IR Code

Code (Hexa)

Function

Note

UP (_D)

DOWN (_E)

VOL+ (^G)

00H

01H

02H

03H

08H

C4H

C5H

09H

10H

11H

12H

13H

14H

15H

16H

17H

18H

19H

0BH

D5H

C6H

5AH

D8H

BFH

0EH

44H

43H

52H

4DH

60H

61H

63H

64H

6BH

40H

41H

69H

6AH

7BH

79H

76H

77H

AFH

99H

R/C Button

R/C Button (Power On/Off)

Discrete IR Code (Only Power On)

Discrete IR Code (Only Power Off)

R/C Button

R/C Button (RGB/DVI/Video/S-video/Component)

Discrete IR Code (Input RGB Selection)

Discrete IR Code (Input DVI Selection)

Discrete IR Code (Input Video Selection)

Discrete IR Code (Input S-video Selection)

Discrete IR Code (Input Component Selection)

R/C Button

R/C Button (PIP/TWIN Exchange)

R/C Button (4:3/16:9)

R/C Button

VOL- (F)

POWER On/Off

POWER ON

POWER OFF

MUTE

Number Key 0

Number Key 1

Number Key 2

Number Key 3

Number Key 4

Number Key 5

Number Key 6

Number Key 7

Number Key 8

Number Key 9

AII INPUT SELECT

RGB

DVI

VIDEO

S-VIDEO

COMPONENT

SLEEP

OK (^Á)

DASP

APC

PIP

SUB INPUT

SWAP

PIP ARC

TWIN PICTURE

ZOOM +

ZOOM -

Window Size

Window Position

Split Zoom

ARC

ARC (4:3)

ARC (16:9)

ARC (ZOOM)

Auto configure

R/C Button

R/C Button(4:3/16:9/Zoom Mode Selection)

Discrete IR Code (Only 4:3 mode)

Discrete IR Code (Only 16:9 mode)

Discrete IR Code (Only ZOOM mode)

Discrete IR Code (Only RGB-PC mode)

32 Plasma Monitor

Troubleshooting Checklist

• Check whether the Monitor is turned on.

• Power cord inserted into wall outlet?

No picture &

No sound

• Test the wall power outlet, plug other product’s power cord into the wall outlet

where the Monitor’s power cord was plugged in.

• Press the VOLUME (G) button.

Picture OK &

No sound

• Sound muted? Press MUTE button.

• Check to see if there is any object between the Plasma Display and the

remote control causing obstruction.

The remote control

• Are batteries installed with correct polarity (+ to +, - to -)?

doesn’t work

(Refer to p.8)

• Install new batteries. (Refer to p.8)

• This is normal, the image is muted during the plasma display startup process.

Please contact your service center, if the picture has not appeared after five

minutes.

Picture appears slowly

after switching on

• Select Color in the VIDEO menu and press the VOLUME (G) button.

(Refer to p.16)

No or Poor color

or Poor picture

• Keep a sufficient distance between the Monitor and the VCR.

• Activate any function to restore the brightness of the picture.

(If still picture is on the screen for more than 5 minutes, the screen gets dark.)

Horizontal/vertical bars

or picture shaking

• Check for local interference such as an electrical appliance or power tool.

No output from one of

the speakers

• Adjust Balance in the AUDIO menu. (Refer to p.17)

• A change in ambient humidity or temperature may result in an unusual noise

when the plasma display is turned on or off and does not indicate a fault with

the monitor.

Unusual sound from

inside the monitor

Owner’s Manual 33

Maintenance

- Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your

new Monitor. Be sure to turn the power off and unplug the power cord before you begin any cleaning.

Cleaning the Screen

1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and

a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the

screen.

2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your Monitor.

Cleaning the Cabinet

To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.

Please be sure not to use a wet cloth.

Extended Absence

If you expect to leave your Monitor dormant for a long time (such as a vacation), it’s a good idea to

unplug the power cord to protect against possible damage from lightning or power surges.

34 Plasma Monitor

Specification

Product Specifications

MU-50PZ44/44A/44B/44K/44R/44S

MU-50PZ44M/44MA/44MB/44MK/44MR/44MS

MU-50PZ44V/44VA/44VB/44VK/44VR/44VS

MU-50PZ90/90A/90B/90K/90R/90S

MU-50PZ90M/90MA/90MB/90MK/90MR/90MS

MU-50PZ90V/90VA/90VB/90VK/90VR/90VS

MODELS

Width (inches / mm)

Height (inches / mm)

Depth (inches / mm)

Weight (pounds / kg)

Power requirement

Resolution

48.2 / 1223

28.9 / 734

4.1 / 105

95.2 / 43.2

AC120V, 60Hz

1366 x 768 (Dot)

Color

16,770,000 (256 steps of each R, G and B)

32 ~ 104°F (0 ~ 40°C)

Less than 80%

Operating Temperature Range

Operating Humidity Range

Maximum Elevation

6561 feet (2000m)

•

The specifications shown above may be changed without notice for quality improvement.

Owner’s Manual 35

IBM 201 User Manual
KitchenAid Cooktop Kdrs505xss01 User Manual
Lenovo 2248 0CN User Manual
Lenovo THINKCENTRE 9641 User Manual
Logitech Wireless Desktop MK710 User Manual
Maytag MEC7636W User Manual
Palsonic 8020PF User Manual
Philips DVD870L User Manual
Philips DVDR3460H User Manual
Philips MCD396 User Manual