User’s Guide
W3000H
Make sure to read the Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for future reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place the
display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release of
heat generated during operation. If these openings are blocked, built-up heat can
cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
Main power breaker is the power cord and this breaking device must be located at
a location where it is easy to operate.
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,
mar, or damage the Active Matrix LCD permanently.
Do not press the LCD screen with your finger for a long time as this may cause
some afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance.
If possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
On Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
On Disposal
The fluorescent lamp used in this product contains a small amount of mercury.
Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of
your local authority.
A2
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Connecting the stand base or Removing the stand base
1.
Place the monitor with its front facing downward on a cushion or soft cloth.
2
.
Align the hooks on the Stand Body with the matching slots in the Stand Base.
Insert the hooks into slots.
3.
Hook
Stand Body
Stand Base
Slot
Warning
The tape and locking pin may only be removed from those monitors equipped with a
standing base when the base is pulled up.
Otherwise, you may be injured by the protruding sections of the stand.
A3
Connecting the Display
4. Attach the monitor to the Stand Base by turning the screw to the right.
Screw : Turn the screw by using the screw handle.
5. Lift and turn the monitor to face towards the front after the connection is
made to the female part of the cable you're attaching.
6. Take the screw out by turning to the left to separate the monitor and Stand
Base.
Important
This illustration depicts the general model of connection. Your monitor may differ from the items
shown in the picture.
Do not carry the product upside down holding only the stand base. The product may fall and get
damaged or injure your foot.
A4
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Positioning your display
1. Adjust the position of the panel in various ways for maximum comfort.
Tilt Range : -5˚~20˚
Swivel Range : 350˚
Height Range : maximum 3.94 inch (100.0mm)
100.0mm
* Please be sure to
remove the Locking
pin to adjust the height.
Ergonom ic
You do not need to replace the Locking pin after it is removed, to adjust its height.
It is recommended that in order to maintain an ergonomic and comfortable
viewing position, the forward tilt angle of the monitor should not exceed 5 degrees.
When adjusting the angle of the screen, do not put your finger(s) in between
the head of the monitor and the stand body. You can hurt your finger(s).
A5
Connecting the Display
Using the Computer
1. First, make sure that the power on the PC, monitor and peripheral equipment are
off and then, connect as follows.
2. Connect DVI-D signal cable
.
When attached, tighten the thumbscrews to secure
1
the connection.
2
3. Insert the power cord
into the outlet.
Varies according to model.
Signal Cable
Power Cord
2
1
Wall-outlet type
DVI-D signal cable
PC
4. Touch the power button on the front of the
monitor to turn on the monitor.
Power button
A6
Connecting the Display
Connecting the USB(Universal Serial Bus) Cable
"USB (Universal Serial Bus)" is an innovation in connecting your different desktop peripherals
conveniently to your computer. By using the USB, you will be able to connect your mouse, keyboard, and
other peripherals to your display instead of having to connect them to your computer. This will give you
greater flexibility in setting up your system. USB allows you to connect a chain of up to 120 devices on a
single USB port; and you can “hot” plug (attach them while the computer is running) or unplug them while
maintaining the Plug and the Plug auto detection and configuration. This display has an integrated BUS-
powered USB hub, allowing up to 2 other USB devices to be attached it.
1. Connect the upstream port of the display to the downstream port of the USB compliant
PC or another hub using the USB cable. (Computer must have a USB port)
2. Connect the USB compliant peripherals to the downstream ports of the display.
USB downstream Port x (4)
Connect the cables from USB
compliant peripherals-such as
mouse, memory stick or USB hard disk, etc.
USB upstream Port x (1)
Connect to downstream connectors of desktop
or laptop computers. (However, the computer
must support USB and have the USB port.)
3. The monitor’s USB terminal supports USB 2.0 and High Speed cables.
High Speed
480Mbps
2.5W
Full Speed
12Mbps
2.5W
Low Speed
Data Rate
Power
1.5Mbps
2.5W
Consumption
(Max,each Port) (Max,each Port)
(Max,each Port)
NOTE
To activate the USB hub function, the display must be connected to a USB compliant
PC(OS) or another hub with the USB cable(enclosed).
When connecting the USB cable, check that the shape of the connector at the cable
side matches the shape at the connecting side.
Even if the display is in a power saving mode, USB compliant devices will function
when they are connected the USB ports(both the upstream and downstream) of the
display.
A7
Connecting the Display
To arrange the cables
Connect the power cord and the signal cable as shown in the figure and then fix them
to the cable holders 1 and 2.
2. Please put the power cord and
1. Please insert the cable holder1
into a hole.
the signal cable in the cable holder 1.
Cable Holder 1
3. Please put the power cord and the signal cable in the cable holder 2.
While pressing the bottom of cable holder 2 with one hand, pull the top of
it with the other hand as shown in the picture.
Pull
Press
Cable Holder 2
A8
Control Panel Functions
Front Panel Controls
4 5
Touching the button to turn the power on and touch
the button again to turn it off.
Power Button
This Indicator lights up blue when the display
operates normally(On Mode). If the display is in Sleep
Mode (Energy Saving), this indicator color changes
to amber.
Power Indicator
You can adjust monitor brightness to be lighter (
or darker ( ). When adjusting brightness, it will beep
once when you reach the maximum or minimum level.
)
Buttons
You can turn DFC function on or off by pressing two buttons at the same time for
longer than three seconds. When DFC is turned on, the power indicator (blue light)
flickers once after the beep. When DFC is turned off, the indicator flickers three
times after the beep.
When DFC is on, if the ꢀ / ꢁ buttons are not pressed at the same time, the
brightness control function might be turned on.
*What is DFC (Digital Fine Contrast) Function? After analyzing input signals,
this product makes dark areas on the screen darker, providing greater contrast
ratio to viewers.
You can turn on or off the alarm ringing when adjusting
buttons while the power is on.
Buttons
Touch any button to check if the sound is on or off. If
sound is heard, it means the sound is on. If not, it means
the sound is off.
You can turn Power Indicator on or off by touching the
Buttons
button lightly while the power is on.
A9
Troubleshooting
Check the following before calling for service.
No image appears
G Is the power cord of the
•
•
Check and see if the power cord is connected
properly to the power outlet.
display connected?
G Is the power on and the
power indicator blue or
green?
Adjust the brightness and the contrast.
G Is the power indicator
•
If the display is in power saving mode, try moving
the mouse or pressing any key on the keyboard to
bring up the screen.
amber?
• Try to turn on the PC
.
Important
Check Control Panel --> Display --> Settings and see if the frequency or the
resolution were changed. If yes, readjust the video card to the recommend
resolution.
Reasons for Recommending Optimal Resolution : The aspect ratio is 16:10.
If the input resolution is not 16:10 (for instance, 16:9, 5:4, 4:3), you might encounter
problems such as blurred letters, blurry screen, cut-off screen display or tilted
screen.
The setting method can differ by computer and O/S (Operation System),
and resolution mentioned above may not be supported by the video card
performance. In this case, please ask to the computer or the video card
manufacturer
.
A10
Troubleshooting
Display image is incorrect
G The screen color is
•
•
•
Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
Make sure the video card is properly inserted in
the slot.
Set the color setting higher than 24 bits (true color)
at Control Panel - Settings.
mono or abnormal.
G The screen blinks.
•
Check if the screen is set to interlace mode and if
yes, change it to the recommend resolution.
Have you installed the display driver?
G
Have you installed the
display driver?
•
Be sure to install the display driver from the display
driver CD (or diskette) that comes with your
display. Or, you can also download the driver from
•
Make sure to check if the video card supports
Plug&Play function.
G
Do you see an
"Unrecognized monitor,
Plug&Play (VESA DDC)
monitor found"
message?
A11
Specifications
Display
30 inches (75.6228cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
30 inches viewable
0.2505 mm pixel pitch
Horizontal Freq.
Vertical Freq.
98.71kHz (Automatic)
59.97 Hz (Automatic)
Sync Input
Input Form
Digital(HDCP)
Signal Input
Input Form
DVI - D connector (Digital)
Digital
Video Input
Resolution
Plug&Play
Max
VESA 2560 x 1600 @ 60 Hz
VESA 2560 x 1600 @ 60 Hz
Recommend
DDC 2B
:
≤
≤
130W(Typ.),140W(USB Full load)
2 W
1 W
On Mode
Sleep Mode
Off Mode
Power
Consumption
Dimensions
&Weight
With Stand
Without Stand
Width
70.27 cm / 27.67 inches
70.27 cm / 27.67 inches
Height 52.54 cm / 20.69 inches(Min) 47.65 cm / 18.76 inches
62.54 cm / 24.62 inches(Max)
Depth 27.02 cm / 10.64 inches
8.30 cm / 3.27 inches
Net
12.3kg (27.12 lbs)
Tilt
-5˚~20˚
350˚
100 mm / 3.94 inches
Tilt Range
Swivel range
Height range
AC 100-240V~ 50/60Hz 1.5A
Power Input
Operating Conditions
Environmental
Conditions
Temperature 10˚C to 35 ˚C
Humidity
10 % to 80 % non-Condensing
Storage Conditions
Temperature -20˚C to 60 ˚C
Humidity
5 % to 90 % non-Condensing
A12
Specifications
Attached ( ), Detached ( O )
Wall-outlet type or PC-outlet type
Stand Base
Power cord
Standard
USB 2.0, Self-Power
Max 480 Mbps
USB
Data Rate
Power Consumption Max 2.5W x 4
NOTE
Information in this document is subject to change without notice.
A13
Specifications
Preset Modes (Resolution)
Display Modes (Resolution)
Horizontal Freq. (kHz)
Vertical Freq. (Hz)
1
*2
1280 x 800
2560 x 1600
49.310
98.713
60
60
*Recommend Mode
Indicator
LED Color
MODE
Blue
Amber
Off
On Mode
Sleep Mode
Off Mode
A14
Installing the Wall mount plate
This monitor satisfies the specifications of the Wall mount plate or
the interchange device.
1. After moving the product to face
downward, make sure to place it on
a soft cloth or a cushion to avoid
surface damage.
2. Remove the screw by using a
screwdriver, and pull the Stand
part in the arrow direction.
Then the Head and Stand parts
are separated.
3. Install the Wall mount plate.
Wall mount plate(Separate purchase)
This is stand-type or wall mount type and is
connectable with Wall mount plate.
Please refer to the installation guide for more
details, which is provided when Wall mount plate
is purchased.
Kensington Security Slot
Connected to a locking
cable that can be purchased
separately at most
computer stores.
A15
Digitally yours
|