LG Electronics LG Life Good Computer Monitor L194WTQ User Manual

User’s Guide  
L194WT  
L204WT  
L194WTM  
L204WTM  
L194WTQ  
L204WTQ  
L194WTX  
L204WTX  
Make sure to read the Important Precautions before using the product.  
Keep the User's Guide(CD) in an accessible place for furture reference.  
See the label attached on the product and give the information to your  
dealer when you ask for service.  
Important Precautions  
On Installation  
Do not allow anything to rest upon or roll over the power cord, and do not place  
the display where the power cord is subject to damage.  
Do not use this display near water such as near a bathtub, washbowl, kitchen  
sink, laundry tub, in a wet basement, or near a swimming pool.  
Displays are provided with ventilation openings in the cabinet to allow the release  
of heat generated during operation. If these openings are blocked, built-up heat  
can cause failures which may result in a fire hazard. Therefore, NEVER:  
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.  
Place the display in a built-in enclosure unless proper ventilation is provided.  
Cover the openings with cloth or other material.  
Place the display near or over a radiator or heat source.  
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,  
mar, or damage the Active Matrix LCD permanently.  
Do not press the LCD screen with your finger for a long time as this may cause  
some afterimages.  
Some dot defects may appear as Red, Green or Blue spots on the screen.  
However, this will have no impact or effect on the display performance.  
If possible, use the recommended resolution to obtain the best image quality for  
your LCD display. If used under any mode except the recommended resolution,  
some scaled or processed images may appear on the screen. However, this is  
characteristic of the fixed-resolution LCD panel.  
On Cleaning  
Unplug the display before cleaning the face of the display screen.  
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display  
screen because over-spraying may cause electrical shock.  
On Repacking  
Do not throw away the carton and packing materials. They make an ideal  
container in which to transport the unit. When shipping the unit to another  
location, repack it in its original material.  
On Disposal  
The fluorescent lamp used in this product contains a small amount of mercury.  
Do not dispose of this product with general household waste.  
Disposal of this product must be carried out in accordance to the regulations of  
your local authority.  
A2  
Connecting the speakers  
-
The feature is only for speaker models - L194WTM, L204WTM  
Connecting the speaker  
1. Place the monitor with its front facing downward on a soft cloth.  
2. Insert the protruding hook of the speaker in the direction of the slot in the back of the product.  
Slot  
Hook  
Audio DC-In  
Cable  
3. After setting up the speaker, connect the Audio DC-In Cable to the back of the product.  
20.1 inch monitor  
19 inch monitor  
A
C
-
I
N
D
C
-O  
U
T
D
-S  
U
B
D
V
I-D  
D
C
-O  
U
T
D
-S  
U
B
D
V
I-D  
A
C
-IN  
A3  
Connecting the Display  
Before setting up the monitor, ensure that the power to the monitor, the computer  
system, and other attached devices is turned off.  
Connecting the stand  
1
.
2.  
Place the monitor with its front facing downward on a soft cloth.  
Assemble the Stand Body into the product in the correct direction as shown in the picture.  
Make sure you push it until you hear it click”.  
R E A R  
3
.
4.  
Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction.  
Once assembled take the monitor up carefully and face the front side  
REAR  
FR  
ONT  
REAR  
R E A R  
FR  
ONT  
Important  
This illustration depicts the general model of connection. Your monitor may differ from  
the items shown in the picture.  
Once you connect the stand base, try not to disconnect it.  
Do not carry the product upside down holding only the stand base. The product may  
fall and get damaged or injure your foot.  
A4  
Connecting the Display  
Before setting up the monitor, ensure that the power to the monitor, the computer  
system, and other attached devices is turned off.  
Positioning your display  
1. Adjust the position of the panel in various ways for maximum comfort.  
Tilt Range : -5˚~20˚  
20  
Warning:  
When adjusting the angle of the screen, do not  
put your finge r(s ) in be tw e e n the he ad of the  
m onitor and the s tand body. You can hurt your  
finger(s).  
Ergonomic  
It is recommended that in order to maintain an ergonomic and comfortable viewing  
position, the forward tilt angle of the monitor should not exceed 5 degrees.  
A5  
Connecting the Display  
Using the Computer  
1. Place the monitor in a convenient, well-ventilated location near your computer.  
2. Connect the signal cable. When attached, tighten the thumbscrews to secure the  
1
connection.  
3. Connect the power cord into a proper power outlet that is easily accessible and close to  
2
the display.  
19 inch monitor  
Signal Cable  
PowerCord  
Analog signal Digital signal  
NOTE  
D-sub  
DVI  
This is a simplified representation  
of the rear view.  
This rear view represents a  
general model; your display may  
differ from the view as shown.  
Varies according to model.  
Wall-outlet type  
2
1
PC-outlet type  
PC  
MAC  
Mac adapter  
For Apple Macintosh use, a separate plug adapter is needed  
to change the 15 pin high density (3 row) D-sub VGA connector  
on the supplied cable to a 15 pin 2 row connector.  
PC  
DVI-D(This feature is not available in all countries.)  
A6  
Connecting the Display  
20.1 inch monitor  
Signal Cable  
Analog signal Digital signal  
PowerCord  
D-sub  
DVI  
Varies according to model.  
Wall-outlet type  
NOTE  
2
This is a simplified representation  
of the rear view.  
This rear view represents a  
general model; your display may  
differ from the view as shown.  
1
PC-outlet type  
DVI-D(This feature is not available in all countries.)  
PC  
PC  
MAC  
Mac adapter  
For Apple Macintosh use, a separate plug adapter is needed to change  
the 15 pin high density (3 row) D-sub VGA connector on the supplied  
cable to a 15 pin 2 row connector.  
4. Press  
button on the front switch panel to turn the power on.  
When monitor power is turned on, the 'Self Image Setting  
Function' is executed automatically.  
(Only Analog Mode)  
NOTE  
‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user  
connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual  
input signals. If you want to adjust the monitor while in use, or wish to manually run this function once again, push the  
‘AUTO/SET’ button on the front panel of the monitor. Otherwise, you may execute the ‘ Factory reset’ option on the  
OSD adjustment menu. However, be aware that this option initializes all the menu items except ‘Language’.  
A7  
Using the speakers - The feature is only for speaker models - L194WTM, L204WTM  
Side Jack  
Headphone/Earphone Input  
Automatically mutes the speaker volume  
when the headphones are plugged in.  
Rear  
Audio Input  
Connects to the *LINE OUT jack of the  
PC sound card.  
*LINE OUT  
A terminal used to connect to the  
AUDIO  
IN  
speaker including a built-in amplifier  
(Amp). Make sure that the connecting  
terminal of the PC sound card is checked  
before connecting. If the Audio Out of PC  
sound card has only Speaker Out,  
reduce the PC volume.  
If the Audio Out of the PC sound card  
supports both Speaker Out and Line Out,  
convert to Line Out using the card  
jumper of the program (Refer to the  
Sound Card Manual).  
Speaker Out  
*Line Out  
<Jack of the PC sound card>  
A8  
Control Panel Functions  
Back  
Front Panel Controls  
Control  
Function  
Use this button to enter or exit the On Screen Display.  
MENU Button  
OSD LOCKED/UNLOCKED  
This function allows you to lock the current control  
settings, so that they cannot be inadvertently changed.  
Press and hold the MENU button for several seconds.  
The message "OSD LOCKED" should appear.  
You can unlock the OSD controls at any time by pushing  
the MENU button for several seconds. The message  
"OSD UNLOCKED" should appear.  
Use these buttons to select or adjust functions in the On  
Screen Display.  
Buttons  
:
For more information, refer to page A16.  
SOURCE Hot key  
Use this button to make D-Sub or DVI connector active.  
This feature is used when two computers are connected  
to the display. The default setting is D-Sub.  
A9  
Control Panel Functions  
Control  
Function  
Use this button to enter a selection in the On Screen  
Display.  
AUTO/SET  
Button  
AUTO IMAGE ADJUSTMENT  
When adjusting your display settings, always press  
the AUTO/SET button before entering the On Screen  
Display(OSD). This will automatically adjust your  
display image to the ideal settings for the current  
screen resolution size (display mode).  
The best display mode is  
19 inch monitor : 1440 x 900  
20.1 inch monitor : 1680 x 1050  
Power Button  
Use this button to turn the display on or off.  
This Indicator lights up blue when the display  
operates normally(On Mode). If the display is in Sleep  
Mode (Energy Saving), this indicator color changes  
to amber.  
Power Indicator  
A10  
On Screen Display (OSD) Control Adjustment  
Screen Adjustment  
Making adjustments to the image size, position and operating parameters of  
the display is quick and easy with the On Screen Display Control system.  
A short example is given below to familiarize you with the use of the controls.  
The following section is an outline of the available adjustments and selections  
you can make using the OSD.  
NOTE  
Allow the display to stabilize for at least 30 minutes before making image adjustments.  
To make adjustments in the On Screen Display, follow these steps:  
Press the MENU Button, then the main menu of the OSD appears.  
To access a control, use the  
or Buttons. When the icon you want  
becomes highlighted, press the AUTO/SET Button.  
Use the  
/
Buttons to adjust the image to the desired level. Use the  
AUTO/SET Button to select other sub-menu items.  
Push the MENU Button once to return to the main menu to select another  
function. Push the MENU Button twice to exit from the OSD.  
A11  
On Screen Display(OSD) Selection and Adjustment  
The following table indicates all the On Screen Display control, adjustment,  
and setting menus.  
Main menu  
Sub-menu  
BRIGHTNESS  
CONTRAST  
GAMMA  
A
D
Reference  
PICTURE  
To adjust the brightness,  
contrast and gamma of the  
screen  
sRGB  
To customize the color of  
the screen  
COLOR  
PRESET  
6500K  
9300K  
RED  
GREEN  
BLUE  
To adjust the position of the  
screen  
HORIZONTAL  
POSITION  
VERTICAL  
CLOCK  
To improve the clarity and  
stability of the screen  
PHASE  
TRACKING  
SHAPNESS  
LANGUAGE  
SETUP  
To customize the screen  
status for a user's operating  
environment  
OSD  
HORIZONTAL  
POSITION VERTICAL  
WHITE BALANCE  
POWER INDICATOR  
FACTORY RESET  
MOVIE / TEXT  
FLATRON  
F-ENGINE  
To select or customize  
desired image settings  
USER  
NORMAL  
: Adjustable  
A : Analog Input  
D : Digital Input  
NOTE  
The order of icons may differ depending on the model (A12~A16 ).  
A12  
On Screen Display(OSD) Selection and Adjustment  
You were introduced to the procedure of selecting and adjusting an item  
using the OSD system. Listed below are the icons, icon names, and icon  
descriptions of the all items shown on the Menu.  
Press the MENU Button, then the main menu of the OSD appears.  
P I C T U R E  
Menu Name  
Sub-menus  
Icons  
Button Tip  
MENU  
SET  
: Exit  
: Adjust (Decrease/Increase)  
: Enter  
: Select another sub-menu  
NOTE  
OSD (On Screen Display) menu languages on the monitor may differ from the manual.  
A13  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
Description  
PICTURE  
P I C T U R E  
To adjust the brightness of the screen.  
To adjust the contrast of the screen.  
BRIGHTNESS  
CONTRAST  
GAMMA  
Set your own gamma value. : -50/0/50  
On the monitor, high gamma values  
display whitish images and low gamma  
values display high contrast images.  
MENU : Exit  
: Decrease  
: Increase  
SET : Select another sub-menu  
COLOR  
C O L O R  
sRGB: Set the screen color to fit the  
SRGB standard color  
PRESET  
specification.  
6500K: Slightly reddish white.  
9300K: Slightly bluish white.  
RED  
Set your own red color levels.  
Set your own green color levels.  
Set your own blue color levels.  
GREEN  
BLUE  
MENU : Exit  
: Decrease  
: Increase  
SET : Select another sub-menu  
POSITION  
P O S I T I O N  
To move image left and right.  
To move image up and down.  
HORIZONTAL  
VERTICAL  
MENU : Exit  
: Decrease  
: Increase  
SET : Select another sub-menu  
A14  
On Screen Display(OSD) Selection and Adjustment  
Main menu  
Sub menu  
CLOCK  
PHASE  
Description  
TRACKING  
T R A C K I N G  
To minimize any vertical bars or stripes  
visible on the screen background.  
The horizontal screen size will also  
change.  
To adjust the focus of the display.  
This item allows you to remove any  
horizontal noise and clear or sharpen  
the image of characters.  
MENU : Exit  
: Decrease  
: Increase  
SHARPNESS To adjust the clearness of the screen.  
SET : Select another sub-menu  
SETUP  
To choose the language in which the  
control names are displayed.  
LANGUAGE  
S E T U P  
OSD  
POSITION  
To adjust position of the OSD window  
on the screen.  
If the output of the video card is different  
the required specifications, the color  
level may deteriorate due to video  
signal distortion. Using this function, the  
signal level is adjusted to fit into the  
standard output level of the video card  
in order to provide the optimal image.  
Activate this function when white and  
black colors are present in the screen.  
WHITE  
BALANCE  
S E T U P  
Use this function to set the power  
indicator on the front side of the monitor  
to ON or OFF.  
If you set OFF, it will go off.  
If you set ON at any time, the power  
indicator will automatically be turned on.  
POWER  
INDICATOR  
MENU : Exit  
: Adjust  
: Adjust  
SET : Select another sub-menu  
FACTORY  
RESET  
Restore all factory default settings except  
"LANGUAGE."  
Press the  
button to reset immediately.  
If this does not improve the screen image, restore the factory default settings.  
If necessary, perform the white balance function again. This function will be enabled only when  
the input signal is an analog signal.  
A15  
On Screen Display(OSD) Selection and Adjustment  
The OSD screen will appear when you touch the  
button  
on the right side of the monitor.  
Menu Name  
Icons  
Sub-menu Name  
FLATRON F-ENGINE  
Screen when applied Screen when not applied  
When you execute F-ENGINE, two tones will appear  
on the screen as shown. The applied screen will  
appear on the left side, whereas the non-applied  
screen will appear on the right side.Touch the SET  
button to use the adjusted screen.  
Main menu  
Sub menu  
Description  
MOVIE This feature lets you easily select the best desired  
TEXT image condition optimized to the environment  
(ambient illumination, image types etc).  
MOVIE: For animation images in videos or movies  
TEXT: For text images (Word processing etc.)  
USER User  
You can manually adjust brightness, ACE or RCM.  
You can save or restore the adjusted value even  
when using a different envir  
To adjust the USER sub-menu function,  
Press the SET Button  
...  
(Brightness): Adjusts screen brightness.  
...  
ACE(Adaptive Clarity Enhancer): Selects the clarity mode.  
...  
RCM(Real Color Management): Selects the color mode.  
0
Not applied  
1
Green enhance  
2
Flesh tone  
3
Color Enhance  
SAVE  
Select the  
sub-menu using the SET button  
and save the YES value using the buttons.  
NORMAL This is under normal operating conditions.  
A16  
Troubleshooting  
Check the following before calling for service.  
No image appears  
G Is the power cord of the  
Check and see if the power cord is connected  
properly to the power outlet.  
display connected?  
G Is the power indicator  
Press the Power button.  
light on?  
Adjust the brightness and the contrast.  
G Is the power on and the  
power indicator blue or  
green?  
G Is the power indicator  
If the display is in power saving mode, try moving  
the mouse or pressing any key on the keyboard to  
bring up the screen.  
amber?  
Try to turn on the PC  
.
This message appears when the signal from the  
G Do you see an "OUT OF  
RANGE" message on  
the screen?  
PC (video card) is out of horizontal or vertical  
frequency range of the display. See the  
'Specifications' section of this manual and  
configure your display again.  
This message appears when the signal cable  
between your PC and your display is not  
connected. Check the signal cable and try again.  
G Do you see a "CHECK  
SIGNAL CABLE"  
message on the  
screen?  
Do you see a "OSD LOCKED" message on the screen?  
G
Do you see OSD  
LOCKEDwhen you  
push MENU button?  
You can secure the current control settings,  
so that they cannot be inadvertently changed.  
You can unlock the OSD controls at any time  
by pushing the MENU button for several  
seconds: the message  
OSD UNLOCKEDwill appear.  
A17  
Troubleshooting  
Display image is incorrect  
G Display Position is  
Press the AUTO/SET button to automatically  
adjust your display image to the ideal setting.  
If the results are unsatisfactory, adjust the image  
position using the H position and V position icon  
in the on screen display.  
incorrect.  
Press the AUTO/SET button to automatically  
adjust your display image to the ideal setting.  
If the results are unsatisfactory, decrease the  
vertical bars or stripes using the CLOCK icon in  
the on screen display.  
G On the screen  
background, vertical  
bars or stripes are  
visible.  
Press the AUTO/SET button to automatically  
adjust your display image to the ideal setting.  
If the results are unsatisfactory, decrease the  
horizontal bars using the PHASE icon in the on  
screen display.  
Check Control Panel --> Display --> Settings  
and adjust the display to the recommended  
resolution or adjust the display image to the ideal  
setting. Set the color setting higher than 24 bits  
(true color).  
G Any horizontal noise  
appearing in any  
image or characters  
are not clearly  
portrayed.  
Important  
Check Control Panel --> Display --> Settings and see if the frequency or the  
resolution were changed. If yes, readjust the video card to the recommend  
resolution.  
The setting method can differ by computer and O/S (Operation System),  
and resolution mentioned above may not be supported by the video card  
performance. In this case, please ask to the computer or the video card  
manufacturer  
.
A18  
Troubleshooting  
Display image is incorrect  
G The screen color is  
Check if the signal cable is properly connected  
and use a screwdriver to fasten if necessary.  
Make sure the video card is properly inserted in  
the slot.  
Set the color setting higher than 24 bits (true color)  
at Control Panel - Settings.  
mono or abnormal.  
Check if the screen is set to interlace mode and if  
yes, change it to the recommend resolution.  
Make sure the power voltage is high enough, It  
has to be higher than AC100-240V 50/60Hz.  
G The screen blinks.  
Have you installed the display driver?  
G
Have you installed the  
display driver?  
Be sure to install the display driver from the display  
driver CD (or diskette) that comes with your  
display. Or, you can also download the driver from  
Make sure to check if the video card supports  
Plug&Play function.  
G
Do you see an  
"Unrecognized monitor,  
Plug&Play (VESA DDC)  
monitor found"  
message?  
A19  
Specifications  
L194WT/L194WTQ/L194WTX  
Display  
19 inches (48.2 cm) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
19 inches viewable  
0.2835 mm pixel pitch  
Horizontal Freq.  
Analog : 30 - 83 kHz (Automatic)  
Digital : 30 - 83 kHz (Automatic)  
56 - 75 Hz (Automatic)  
Separate TTL, Positive/Negative  
SOG (Sync On Green)  
Digital  
Sync Input  
Vertical Freq.  
Input Form  
Signal Input  
15 pin D-Sub Connector  
Video Input  
DVI - D connector (Digital)  
Input Form  
Max  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Analog : VESA 1440 x 900 @75 Hz  
Digital : VESA 1440 x 900 @60 Hz  
VESA 1440 x 900 @60 Hz  
Resolution  
Plug&Play  
Recommend  
DDC 2B  
:
34 W(Typ.)  
1 W  
1 W  
Power  
Consumption  
0n Mode  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
&Weight  
Width 43.48 cm / 17.11 inches 43.48 cm / 17.11 inches  
Height 36.99 cm / 14.56 inches 28.73 cm / 11.31 inches  
Depth 22.60 cm / 8.89 inches  
5.87 cm / 2.31 inches  
Net  
Tilt  
3.6 kg (7.94 lbs)  
-5˚~20˚  
Tilt Range  
AC 100-240V~ 50/60Hz 0.8A  
Power Input  
Operating Conditions  
Environmental  
Conditions  
Temperature 10˚C to 35 ˚C  
Humidity  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature -20˚C to 60 ˚C  
Humidity  
5 % to 90 % non-Condensing  
Attached ( ), Detached ( O )  
Attached ( ), Detached ( O )  
Wall-outlet type or PC-outlet type  
Stand Base  
Signal cable  
Power cord  
NOTE  
Information in this document is subject to change without notice.  
A20  
Specifications  
L194WTM  
19 inches (48.2 cm) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
19 inches viewable  
0.2835 mm pixel pitch  
Display  
Sync Input  
Video Input  
Horizontal Freq.  
Analog : 30 - 83 kHz (Automatic)  
Digital : 30 - 83 kHz (Automatic)  
56 - 75 Hz (Automatic)  
Separate TTL, Positive/Negative  
SOG (Sync On Green),Digital  
15 pin D-Sub Connector  
Vertical Freq.  
Input Form  
Signal Input  
DVI - D connector (Digital)  
Input Form  
Max  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Analog : VESA 1440 x 900 @75 Hz  
Digital : VESA 1440 x 900 @60 Hz  
VESA 1440 x 900 @60 Hz  
Resolution  
Plug&Play  
Recommend  
DDC 2B  
:
34 W(Typ.)  
1 W  
1 W  
Power  
Consumption  
(without speaker)  
0n Mode  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
&Weight  
Width 43.48 cm / 17.11 inches 43.48 cm / 17.11 inches  
Height 36.99 cm / 14.56 inches 28.73 cm / 11.31 inches  
Depth 22.60 cm / 8.89 inches  
5.87 cm / 2.31 inches  
Net  
Tilt  
3.6 kg (7.94 lbs)  
-5˚~20˚  
Tilt Range  
AC 100-240V~ 50/60Hz 0.8A  
Power Input  
Operating Conditions  
Environmental  
Conditions  
Temperature 10˚C to 35 ˚C  
Humidity  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature -20˚C to 60 ˚C  
Humidity  
5 % to 90 % non-Condensing  
Attached ( ), Detached ( O )  
Attached ( ), Detached ( O )  
Wall-outlet type or PC-outlet type  
Stand Base  
Signal cable  
Power cord  
Audio  
RMS Audio Output  
1W+1W(R+L)  
Input Sensitivity  
Speaker Impedance  
0.7Vrms  
16  
NOTE  
Information in this document is subject to change without notice.  
A21  
Specifications  
L204WT/L204WTQ/L204WTX  
Display  
20.1 inches (51.1 cm) Flat Panel Active matrix-TFT LCD  
Anti-Glare coating  
20.1 inches viewable  
0.258 mm pixel pitch  
Horizontal Freq. Analog : 30 - 83 kHz (Automatic)  
Digital : 30 - 83 kHz (Automatic)  
Sync Input  
Vertical Freq.  
Input Form  
56 - 75 Hz (Automatic)  
Separate TTL, Positive/Negative  
SOG (Sync On Green)  
Digital  
Signal Input  
15 pin D-Sub Connector  
Video Input  
DVI - D connector (Digital)  
Input Form  
Max  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Analog : VESA 1680 x 1050 @ 60 Hz  
Digital : VESA 1680 x 1050 @ 60 Hz  
VESA 1680 x 1050 @60 Hz  
Resolution  
Plug&Play  
Recommend  
DDC 2B  
:
45W(Typ.)  
1 W  
1 W  
Power  
Consumption  
0n Mode  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
&Weight  
Width 46.62 cm / 18.35 inches 46.62 cm / 18.35 inches  
Height 38.40 cm / 15.11 inches 30.54 cm / 12.02 inches  
Depth 22.60 cm / 8.89 inches  
6.46 cm / 2.54 inches  
Net  
Tilt  
4.8 kg (10.58 lbs)  
Tilt Range  
-5˚~20˚  
AC 100-240V~ 50/60Hz 1.2A  
Power Input  
Operating Conditions  
Environmental  
Conditions  
Temperature 10˚C to 35 ˚C  
Humidity  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature -20˚C to 60 ˚C  
Humidity  
5 % to 90 % non-Condensing  
Stand Base  
Signal cable  
Power cord  
Attached ( ), Detached ( O )  
Attached ( ), Detached ( O )  
Wall-outlet type or PC-outlet type  
NOTE  
Information in this document is subject to change without notice.  
A22  
Specifications  
L204WTM  
20.1 inches (51.1 cm) Flat Panel Active matrix-TFT LCD  
Display  
Anti-Glare coating  
20.1 inches viewable  
0.258 mm pixel pitch  
Sync Input  
Video Input  
Horizontal Freq. Analog : 30 - 83 kHz (Automatic)  
Digital : 30 - 83 kHz (Automatic)  
Vertical Freq.  
Input Form  
56 - 75 Hz (Automatic)  
Separate TTL, Positive/Negative  
SOG (Sync On Green) Digital  
15 pin D-Sub Connector  
Signal Input  
DVI - D connector (Digital)  
Input Form  
Max  
RGB Analog (0.7 Vp-p/ 75 ohm), Digital  
Analog : VESA 1680 x 1050 @60 Hz  
Digital : VESA 1680 x 1050 @60 Hz  
VESA 1680 x 1050 @60 Hz  
Resolution  
Plug&Play  
Recommend  
DDC 2B  
:
45W(Typ.)  
1 W  
1 W  
Power  
Consumption  
(without speaker)  
0n Mode  
Sleep Mode  
Off Mode  
With Stand  
Without Stand  
Dimensions  
&Weight  
Width 46.62 cm / 18.35 inches 46.62 cm / 18.35 inches  
Height 38.40 cm / 15.11 inches 30.54 cm / 12.02 inches  
Depth 22.60 cm / 8.89 inches  
6.46 cm / 2.54 inches  
Net  
Tilt  
4.8 kg (10.58 lbs)  
Tilt Range  
-5˚~20˚  
Power Input  
AC 100-240V~ 50/60Hz 1.2A  
Operating Conditions  
Environmental  
Conditions  
Temperature 10˚C to 35 ˚C  
Humidity  
10 % to 80 % non-Condensing  
Storage Conditions  
Temperature -20˚C to 60 ˚C  
Humidity  
5 % to 90 % non-Condensing  
Stand Base  
Signal cable  
Power cord  
Attached ( ), Detached ( O )  
Attached ( ), Detached ( O )  
Wall-outlet type or PC-outlet type  
Audio  
RMS Audio Output  
1W+1W(R+L)  
Input Sensitivity  
Speaker Impedance  
0.7Vrms  
16Ω  
NOTE  
Information in this document is subject to change without notice.  
A23  
Specifications  
Preset Modes (Resolution)  
19 inch monitor  
Display Modes (Resolution)  
Horizontal Freq. (kHz)  
Vertical Freq. (Hz)  
70  
70  
60  
75  
60  
75  
75  
60  
75  
75  
65  
60  
75  
60  
60  
75  
1
2
3
4
5
6
7
8
9
640 x 350  
720 x 400  
640 x 480  
640 x 480  
800 x 600  
800 x 600  
832 x 624  
1024 x 768  
1024 x 768  
1152 x 870  
1152 x 900  
1280 x 1024  
1280 x 1024  
1440 x 900  
1440 x 900  
1440 x 900  
31.469  
31.468  
31.469  
37.500  
37.879  
46.875  
49.725  
48.363  
60.123  
68.681  
61.805  
63.981  
79.976  
55.500  
55.935  
70.635  
10  
11  
12  
13  
14  
*15  
**16  
*Recommend Mode  
**Only Analog Mode  
20.1 inch monitor  
Display Modes (Resolution)  
Horizontal Freq. (kHz)  
Vertical Freq. (Hz)  
1
2
3
4
5
6
7
8
9
720 x 400  
640 x 480  
640 x 480  
800 x 600  
800 x 600  
1024 x 768  
1024 x 768  
1152 x 864  
1280 x 1024  
1280 x 1024  
1680 x 1050  
1680 x 1050  
31.468  
31.469  
37.500  
37.879  
46.875  
48.363  
60.123  
67.500  
63.981  
79.976  
64.674  
65.290  
70  
60  
75  
60  
75  
60  
75  
75  
60  
75  
60  
60  
10  
*11  
**12  
*
Digital Recommend Mode  
** Analog Recommend Mode  
A24  
Specifications  
Indicator  
LED Color  
MODE  
blue  
amber  
Off  
On Mode  
Sleep Mode  
Off Mode  
Signal Connector Pin Assignment  
8
16  
24  
1
9
17  
DVI-D Connector  
Pin  
1
2
3
4
5
6
7
8
Signal(DVI-D)  
T. M. D. S. Data2-  
T. M. D. S. Data2+  
T. M. D. S. Data2/4 Shield  
T. M. D. S. Data4-  
T. M. D. S. Data4+  
DDC Clock  
Pin  
16  
Signal(DVI-D)  
Hot Plug Detect  
T. M. D. S. Data0-  
T. M. D. S. Data0+  
T. M. D. S. Data0/5 Shield  
T. M. D. S. Data5-  
T. M. D. S. Data5+  
T. M. D. S. Clock Shield  
T. M. D. S. Clock+  
T. M. D. S. Clock-  
17  
18  
19  
20  
21  
22  
23  
24  
DDC Data  
Analog Vertical Sync.  
T. M. D. S. Data1-  
T. M. D. S. Data1+  
T. M. D. S. Data1/3 Shield  
T. M. D. S. Data3-  
T. M. D. S. Data3+  
+5V Power  
9
10  
11  
12  
13  
14  
15  
Ground (return for +5V,  
H. Sync. and V. Sync.)  
T. M. D. S. (Transition Minimized Differential Signaling)  
A25  
Installing the Wall mount plate  
This monitor satisfies the specifications of the Wall mount plate or  
the interchange device.  
1. Place the monitor with its front facing downward on a soft cloth.  
2. Hold the body of the stand as shown in the image  
and bend slightly to the  
1
right.  
2
3. Pull the stand to the direction as shown in the image  
to separate.  
1
2
R
A
E
R
T
4. Install the Wall mount plate.  
Wall mount plate(Separate purchase)  
This is stand-type or will mount type and is  
connectable with Wall mount plate.  
Please refer to the installation guide for more  
details, which is provided when Wall mount plate is  
purchased.  
Kensington Security Slot  
Connected to a locking  
cable that can be purchased  
separately at most  
computer stores  
A26  
Digitally yours  

IBM CIO DIO48H User Manual
Intel SKA4 User Manual
Mitsubishi Electronics DV158 User Manual
Moffat Blue Seal E516A B User Manual
NEC MultiSync V551 User Manual
Nortel Networks M 901 User Manual
Philips 28PT7138 User Manual
Philips 32PFL3X06H User Manual
Philips 63KV5657 User Manual
Philips CD645IB User Manual