LG Electronics LG Life Good Computer Monitor E1951T User Manual

OWNER’S MANUAL

LED LCD MONITOR

Please read this manual carefully before operating

your set and retain it for future reference.

LED LCD MONITOR MODELS

E1951S E1951T E2251VR E2251VQ

E2051S E2051T E2351VR E2351VQ

E2251S E2251T

E2351T

www.lg.com

ASSEMBLING AND PREPARING

AsseMBLInG AnD PRePARInG

Unpacking

Check your product box for the following items. If there are any missing accessories, contact the local

dealer where you purchased your product. The illustrations in this manual may differ from the actual product

and accessories.

DVI-D Cable

CD(owner's Manual) /

D-sUB Cable

(E1951T/E2051T/E2251T/E2351T/

E2251VR/E2351VR/E2251VQ/

E2351VQ)

Card

(This signal cable may be attached

to this product before shipping out.)

(This cable is not included in all

countries.)

Power Cord

AC-DC Adapter

stand Base

stand Body

two screws

CAUtIon

Do not use any unapproved accessories to ensure the safety and product life span.

Any damages or injuries by using unapproved accessories are not covered by the warranty.

note

The accessories supplied with your product may vary depending on the model.

Product specifications or contents in this manual may be changed without prior notice due to upgrade

of product functions.

User should use shielded signal interface cables (RGB cable) with ferrite cores (core in the

connector) to maintain standard compliance for the product.

ASSEMBLING AND PREPARING

Parts and buttons

Power Indicator

Lighting on: turned on

Lighting off: turned off

(Power Button)

Button ("CUSTOMIZING

SETTINGS" on page 13)

E2251VR E2251VQ

E2351VR E2351VQ

E1951S E2051S E2251S

E1951T E2051T

E2251T E2351T

Connection panel (See p.10)

ASSEMBLING AND PREPARING

Button

Description

Accesses the main menus.(See p.14)

Left First Button

osD LoCKeD/

UnLoCKeD

This function allows you to lock the current control settings, so

that they cannot be inadvertently changed.

Press and hold the Left First Button for several seconds.

The message "OSD LOCKED" should appear.

You can unlock the OSD controls at any time by pushing the

Left First Button for several seconds. The message "OSD

UNLOCKED" should appear.

SUPER+ RESOLUTION

DUAL

Use this button to enter the SUPER+ RESOLUTION menu. For more information.(See p.16)

Use this button to enter the DUAL menu.

For more information.(See p.17)

AUTO

To automatically adjust the screen, press the AUTO button on the MONITOR SETUP

OSD. (Only supported in Analog Mode)

the best display mode

e1951s / e1951t

e2051s / e2051t

1366 x 768

1600 x 900

1920 x 1080

e2251s / e2251t

e2251VR / e2251VQ

e2351t / e2351VR

e2351VQ

VOLUME (Only HDMI mode) e2251VR / e2351VR / e2251VQ / e2351VQ

Adjust the volume of the Monitor set.(See p.16)

INPUT

You can choose the input signal.

When two input signals are at least are connected, you can select the input signal

(D-SUB/HDMI) you want.

When only one signal is connected, it is automatically detected. The default setting is

D-SUB.

EXIT

Exit the OSD(On Screen Display).

Turns the power on or off.

(Power Button)

Power Indicator

The power indicator stays white if the display is running

properly (On Mode). If the display is in Sleep Mode, the power

indicator color is red.

ASSEMBLING AND PREPARING

Using a coin, turn the screw clockwise to se-

cure the stand base.

setting Up the Monitor set

Attaching the stand Base

Place the monitor's screen face down.

CAUtIon

To protect the screen from scratches, cover

the surface with a soft cloth.

Put the stand Body on the set and use the

screws to fix.

stand Base

Detaching the stand base

Place the monitor's screen face down.

To protect the screen from scratches, cover the

surface with a soft cloth.

Using a coin, turn the screw in the stand base

counterclockwise. Detach the stand base from

the stand body.

stand Body

Check the position (at the front and rear) of

the stand body, then mount the stand base on

the stand body as shown in the figure.

stand Body

stand Base

CAUtIon

stand Base

This illustration depicts the general type of

connection. Your monitor may differ from the

items shown in the picture.

Do not carry the product upside down

holding only the stand base. The product

may fall and get damaged or injure your

foot.

CAUtIon

Push stand base tightly before turn the

screw in.

ASSEMBLING AND PREPARING

Connect the AC-DC Adapter and Power Cord

to a wall outlet.

Detaching the stand Body (Using

the Wall mount)

Remove 2 screws and detach the Stand Body.

Press Power button on the front switch of panel

to turn the power on.

CAUtIon

Mounting on a table

Disconnect the power cord first, and then move

or install the Monitor set. Otherwise electric

shock may occur.

Lift and tilt the Monitor set into its upright

position on a table.

Leave a 10 cm (minimum) space from the wall

for proper ventilation.

10 cm

ASSEMBLING AND PREPARING

manual supplied with the Kensington security

system or visit http://www.kensington.com.

WARnInG

When you adjust the angle, do not hold the

bottom of the Monitor set frame as shown on

the following illustration, as it may injure your

fingers.

Connect the Kensington security system cable

between the Monitor set and a table.

Do not touch or press the screen when

adjusting the angle of the monitor.

note

The Kensington security system is optional.

You can obtain it from most electronics stores.

Mounting on a wall

For proper ventilation, allow a clearance of 10 cm

on each side and from the wall. Detailed

instructions are available from your dealer, see the

optional Tilt Wall Mounting Bracket Installation and

Setup Guide.

note

Tilt from +15 to -5 degrees up or down to adjust

the angle of the Monitor set to suit your view.

- 5

10 cm

Front

Rear

Using the Kensington security system

The Kensington security system connector is

located at the back of the Monitor set. For more

information of installation and using, refer to the

ASSEMBLING AND PREPARING

If you intend to mount the Monitor set to a wall, an

optional third-party wall mount must be purchased.

When you install the Monitor set using the wall

mounting interface (optional parts), attach it

carefully so it will not fall.

VESA (A x B)

Please use screws and a wall mount interface

in accordance with VESA Standards.

If you use screws longer than standard, the

monitor might be damaged internally.

If you use improper screws, the product might be

damaged and drop from mounted position. In

this case, LG Electronics is not responsible for it.

CAUtIon

VESA compatible only with respect to screw

mounting interface dimensions and mounting

screw specifications.

Disconnect the power cord first before

moving or installing the Monitor set.

Otherwise electric shock may occur.

If you install the Monitor set on a ceiling or

slanted wall, it may fall and result in severe

injury.

Use only an authorized LG wall mount and

contact a local dealer or qualified personnel.

Do not over tighten the screws as this may

cause damage to the Monitor set and void

your warranty.

Please use a VESA standard as below.

784.8 mm (30.9 inch) and under

* Wall Mount Pad Thickness : 2.6 mm

* Screw : 4.0 mm x Pitch 0.7 mm x

Length 10 mm

787.4 mm (31.0 inch) and above

* Please use VESA standard wall mount pad

and screws.

Use only screws and wall mounts that

meet the VESA standard. Any damages

or injuries by misuse or using an improper

accessory are not covered by the warranty.

Model

E1951S

E2051S E2251VR

E2251S E2351VR

E2351T

E2251VQ

E2351VQ

E1951T

E2051T

E2251T

note

VesA (A x B)

screw size

number of screws

Wall mount bracket

(optional)

75 x 75

Only use screws that are listed on the VESA

standard screw specifications.

The wall mount kit will include an installation

manual and necessary parts.

The wall mount bracket is optional. You can

obtain additional accessories from your local

dealer.

RW120

The length of screws may differ depending

on the wall mount. Be sure to use the proper

length.

For more information, refer to the

instructions supplied with the wall mount.

USING THE MONITOR SET

UsInG tHe MonItoR set

Connecting to a PC

E2251VR E2351VR E2251VQ E2351VQ

Your Monitor set supports Plug & Play*.

*Plug & Play: A PC recognizes a connected

device that users connect to a PC and turn

on, without device configuration or user

intervention.

D-sUB connection

Transmits analog video from your PC to the

Monitor set. Connect the PC and the Monitor set

with the supplied D-sub 15 pin signal cable as

shown in the following illustrations.

E1951S E2051S E2251S

note

Apple Adapter

An adapter may be needed for Apple

computers. This adapter can be purchased

from Apple.

E1951T E2051T E2251T E2351T

USING THE MONITOR SET

DVI to HDMI connection

CAUtIon

Transmits the digital video signal from your PC to

the Monitor set. Connect the PC and the Monitor

set with the DVI to HDMI cable as shown the

following illustrations.

Connect the signal

input cable and tighten

it by turning the screws

clockwise.

E1951T E2051T E2251T E2351T

Do not press the screen with your finger for

a long time as this may result in temporary

distortion on the screen.

Avoid displaying a fixed image on the

screen for a long period of time to prevent

image burn. Use a screensaver if possible.

E2251VR E2351VR E2251VQ E2351VQ

USING THE MONITOR SET

Self Image Setting Function

HDMI connection

Press the power button on the front panel to turn

the power on. When monitor power is turned on,

the "self Image setting" Function is executed

automatically. (Only supported in Analog Mode)

Transmits the digital video and audio signals from

your PC or A/V to the Monitor set. Connect the PC

or A/V and the Monitor set with the HDMI cable

as shown in the following illustrations. When the

HDMI cable is connected, you can listen to the

sound through headphones, earphones or an

external speaker.

E2251VR E2351VR E2251VQ E2351VQ

note

"self Image setting" Function.

This function provides the user with optimal

display settings.When the user connects

the monitor for the first time, this function

automatically adjusts the display to optimal

settings for individual input signals.(Only

supported in Analog Mode)

note

‘AUto’ Function.

If you use HDMI PC, it can cause compatibility

problem.

When you encounter problems such as

blurry screen, blurred letters, screen flicker

or tilted screen while using the device or

after changing screen resolution, press the

AUTO function button to improve resolution.

(Only supported in Analog Mode)

When you want to use two PC in our Monitor,

please connect the signal cable(D-SUB/

DVI-D/HDMI) respectively in Monitor set.

If you turn the Monitor set on while it is cold,

the screen may flicker. This is normal.

Some red, green, or blue spots may appear

on the screen. This is normal.

Sound output is available only in HDMI input

mode. The quality of the sound may be

reduced depending on the performance of

headphones, earphones or external speaker.

CUSTOMIZING SETTINGS

CUstoMIZInG settInGs

Accessing the Main Menus

Press any button on the front of the Monitor set to display the MonItoR setUP OSD menu.

Press the desired menu item.

Change the value of the menu item by pressing the buttons on the front of the Monitor set.

To return to the upper menu or set other menu items, use the up arrow ( ) button.

Select eXIt to leave the OSD menu.

Monitor set Buttons

MenU (See p.14)

AUto (See p.5)

eXIt

Sets the screen options.

Optimizes the resolution.

Exits the OSD menu.

MONITOR SETUP

SUPER+

RESOLUTION

DUAL

AUTO

VOLUME

INPUT

EXIT

sUPeR+ ResoLUtIon

DUAL (See p.17)

VoLUMe (See p.16)

InPUt

(See p.16)

Sets the external input.

note

Different menu items are enabled depending on the type of input signal and model.

sUPeR+

DUAL AUto VoLUMe InPUt eXIt

ResoLUtIon

e1951s / e2051s / e22551s

e1951t / e2051t / e2251t / e2351t

e2251VR / e2351VR (Analog/Digital)

e2251VR / e2351VR (HDMI)

e2251VQ / e2351VQ (Analog/Digital)

e2251VQ / e2351VQ (HDMI)

CUSTOMIZING SETTINGS

Customizing settings

Menu settings

BRIGHTNESS

100

Press any button on the front of the Monitor set to display the

ORIGINAL RATIO

COLOR TEMP

PRESET

RED

GREEN

WIDE

PRESET

WARM

MonItoR setUP OSD menu.

Press the MenU button to display the options in the OSD

menu.

BLUE

Set the options by pressing the ◄ or ► or ▼ buttons.

CONTRAST

BLACK LEVEL

LANGUAGE

RTC

LOW

ENGLISH

Select eXIt to leave the OSD menu.

To return to the upper menu or set other menu items, use the

up arrow ( ) button.

SUPERENEYGYSAVING

FACTORY RESET

EXIT

The available MENU settings are described below.

Analog Digital

HDMI

Description

BRIGHtness

oRIGInAL RAtIo

Adjusts the brightness of the screen.

WIDe

Switch to full screen mode according to input image signal.

oRIGInAL

Change the input image signal ratio to original.

* This function works only if input resolution is lower than Monitor

set ratio (16:9).

CoLoR teMP

PReset

Select the screen color.

WARM: Set the screen to warm color temperature (more red).

MeDIUM: Set the screen to medium color temperature.

CooL: Set the screen to cool color temperature (More blue).

UseR

ReD: Set your own red color levels.

GReen: Set your own green color levels.

BLUe: Set your own blue color levels.

ContRAst

Adjusts the contrast of the screen.

BLACK LeVeL

(only supported

in HDMI mode)

You can set the offset level. If you select 'HIGH', the screen will be

bright and if you select ‘LOW’, the screen will be dark.

offset: As the criteria for video signal, it is the darkest screen

the monitor can show.

LAnGUAGe

Changes the menu language.

RtC

If you set on, you enable the Response Time Control function and

reduce the afterimage of the screen.

If you set oFF, you disable the Response Time Control function

and operate at panel response time.

(only supported in

e2251VQ, e2351VQ

model)

sUPeR eneRGY

sAVInG

Change the SUPER ENERGY SAVING function. (See p.15)

FACtoRY Reset

Returns the monitor to original factory settings except

"LANGUAGE".

Analog: D-SUB(Analog signal) input.

Digital: DVI-D(Digital signal) input.

HDMI: HDMI(Digital signal) input.

CUSTOMIZING SETTINGS

sUPeR eneRGY sAVInG settings

SUPER ENERGY SAVING

Press any button on the front of the Monitor set to

display the MonItoR setUP OSD menu.

OFF

RESET

Press the MenU button to display the options in the

OSD Menu.

SUPER

SAVING

: 5 W/h

TOTAL POWER REDUCTION: 20 W

TOTAL CO2 REDUCTION: 16 g

LED SAVING

Select sUPeR eneRGY sAVInG by pressing the

▼ button.

: 12 W/h

Enter to sUPeR eneRGY sAVInG by pressing the

► button.

EXIT

Set the options by pressing ◄ or ► buttons.

Select eXIt to leave the OSD menu.

To return to the upper menu or set other menu items,

use the up arrow ( ) button.

The available SUPER ENERGY SAVING settings are described below.

Description

Enables SUPER ENERGY SAVING.

Disables SUPER ENERGY SAVING.

oFF

Reset

Resets the values of total energy consumption reduction and CO2 emission reduction estimates.

note

totAL PoWeR ReDUCtIon: How much power is saved while using the monitor.

totAL Co2 ReDUCtIon: Estimated CO2 not used by activating the Super Energy Saving function.

sAVInG DAtA(W/h)

470 mm (18.5 inch) 508 mm (20 inch) 546 mm (21.5 inch) 584 mm (23 inch)

SUPER SAVING

LED SAVING

3 W/h

4 W/h

5 W/h

18 W/h

15 W/h

12 W/h

Saving Data depends on the Panel. So,those values should be different from each panel and panel

vendor.

LG calculated these values by using “broadcast video signal”.

LED Saving means how much power can be saved using a WLED Panel instead of CCFL panel.

SUPER SAVING means how much power can be saved using the SUPER ENERGY SAVING

function.

CUSTOMIZING SETTINGS

SUPER+ RESOLUTION

sUPeR+ ResoLUtIon settings

Press any button on the front of the Monitor set to

display the MonItoR setUP OSD menu.

NORMAL

LOW

MEDIUM

HIGH

EXIT

Press the sUPeR+ ResoLUtIon button to display

the options in the OSD menu.

Set the options by pressing ◄ or ► buttons.

Select eXIt to leave the OSD menu.

To return to the upper menu or set other menu items,

use the up arrow ( ) button.

EXIT

The available SUPER+ RESOLUTION settings are described below.

noRMAL

Description

Select this for most environments. SUPER+ RESOLUTION is turned off.

LoW

Optimizes the screen for natural video with soft images. It is effective for still images or video with

little movement.

MeDIUM

HIGH

Slightly sharpens images. Use with lower quality and SD video.

Optimizes the screen for sharp video with clear images. It is effective for high resolution video and

games.

note

sR (sUPeR+ ResoLUtIon) will help remove noise from video.

Volume settings (only supported in HDMI)

VOLUME

Press any button on the front of the Monitor set to display the

MonItoR setUP OSD menu.

Press the VoLUMe button to display the options in the OSD

menu.

EXIT

Adjust the VoLUMe by pressing ◄ or ► buttons.

EXIT

Select eXIt to leave the OSD menu.

To return to the upper menu or set other menu items, use the up

arrow ( ) button.

CUSTOMIZING SETTINGS

DUAL PACKAGE

DUAL MONITOR

►

DUAL MonItoR settings

Press any button on the front of the Monitor set to display the

MonItoR setUP OSD menu.

Press the DUAL button to display the options in the OSD menu.

Set the options by pressing ▼ and then ◄ and ► buttons.

Select eXIt to leave the OSD menu.

OFF

EXTENDED

CLONE

EXIT

To return to the upper menu or set other menu items, use the

up arrow ( ) button.

The available DUAL MONITOR settings are described below.

Description

Turns the Dual Monitor feature off.

DUAL MonItoR oFF

eXtenDeD

Extends the desktop of the primary monitor to the secondary monitor.

EXIT

CLone

Shows the same video on both monitors.

DUAL PACKAGE

DUAL WEB

►

DUAL WeB settings

Press any button on the front of the Monitor set to display the

MonItoR WeB OSD menu.

Press the DUAL button to display the options in the OSD menu.

Set the options by pressing ▼ and then ◄ and ► buttons.

Select eXIt to leave the OSD menu.

OFF

EXIT

To return to the upper menu or set other menu items, use the up

arrow ( ) button.

The available DUAL WEB settings are described below.

Description

DUAL WeB

Automatically arranges (snaps) web pages to each half of the screen.

Turns the Dual Web feature off.

oFF

note

When the monitor is in power saving mode, pressing any button and then selecting Dual Package,

the monitor will return to normal operation.

The Dual Package program provided with the monitor should be installed on the PC to use the Dual

Monitor and Dual Web functions.

TROUBLESHOOTING

tRoUBLesHootInG

Check the following before calling for service.

no image appears

Is the power cord of the display

connected?

Check and see if the power cord is connected properly to the power

outlet.

Is the power indicator light on?

Is the power indicator red?

Press the Power button.

If the display is in power saving mode, try moving the mouse or

pressing any key on the keyboard to bring up the screen.

Try to turn on the PC.

Do you see an "OUT OF RANGE"

message on the screen?

This message appears when the signal from the PC (video card) is

out of horizontal or vertical frequency range of the display. See the

'Specifications' section of this manual and configure your display

again.

Do you see a "CHECK SIGNAL

CABLE" message on the screen?

This message appears when the signal cable between your PC and

your display is not connected. Check the signal cable and try again.

Do you see a "osD LoCKeD" message on the screen?

Do you see “OSD LOCKED” when

you push Left First Button?

You can secure the current control settings, so that they cannot be

inadvertently changed. You can unlock the OSD controls at any time

by pushing the left first button for several seconds: the message “OSD

UNLOCKED” will appear.

Display image is incorrect

Display Position is incorrect.

Press the AUto button to automatically adjust your display image to

the ideal setting.

On the screen background, vertical

bars or stripes are visible.

Press the AUto button to automatically adjust your display image to

the ideal setting.

Any horizontal noise appearing in

any image or characters are not

clearly portrayed.

Press the AUto button to automatically adjust your display image to

the ideal setting.

Check Control Panel ► Display ► Settings and adjust the display

to the recommended resolution or adjust the display image to the ideal

setting. Set the color setting higher than 24 bits (true color).

CAUtIon

Check Control Panel ► Display ► Settings and see if the frequency or the resolution were

changed. If yes, readjust the video card to the recommend resolution.

If the recommended resolution (optimal resolution) is not selected, letters may be blurred and the

screen may be dimmed, truncated or biased. Make sure to select the recommend resolution.

The setting method can differ by computer and O/S (Operating System), and resolution mentioned

above may not be supported by the video card performance. In this case, please ask to the computer

or the video card manufacturer.

TROUBLESHOOTING

Display image is incorrect

The screen color is mono or

abnormal.

Check if the signal cable is properly connected and use a screwdriver

to fasten if necessary.

Make sure the video card is properly inserted in the slot.

Set the color setting higher than 24 bits (true color) at Control Panel

► settings.

The screen blinks.

Check if the screen is set to interlace mode and if yes, change it to the

recommend resolution.

Do you see an "Unrecognized monitor, Plug&Play (VesA DDC) monitor found" message?

Have you installed the display

driver?

A Windows display driver is included on the CD. Or, you can also

download the driver from our web site: http://www.lg.com.

Make sure to check if the video card supports Plug&Play function.

the Audio function is not working

Picture OK & No sound.

Check whether volume is "0".

Check sound muted.

HDMI cable installed properly.

Head phone cable installed properly.

Check sound format. Not support to compressed sound format.

SPECIFICATIONS

sPeCIFICAtIons

E1951S

E1951T

Display

screen type

47.0 cm (18.5 inch) Flat Panel Active matrix-TFT LCD

Anti-Glare coating

Visible diagonal size: 47.0 cm

Pixel Pitch

0.3 mm x 0.3 mm (Pixel Pitch)

sync Input

Horizontal Frequency 30 kHz to 61 kHz (Automatic)

Vertical Frequency

Input Form

e1951s

56Hz to 75Hz (Automatic)

Separate Sync.

e1951t

Separate Sync. Digital

Video Input

signal Input

e1951s

15 pin D-SUB Connector

e1951t

15 pin D-SUB Connector /DVI-D Connector (Digital)

Input Form

e1951s

e1951t

Max

RGB Analog (0.7 Vp-p/ 75 ohm)

RGB Analog (0.7 Vp-p/ 75 ohm), Digital

Resolution

e1951s

e1951t

Recommend

e1951s

e1951t

D-SUB(Analog) : 1366 x 768 @ 60 Hz

D-SUB(Analog) / DVI(Digital): 1366 x 768 @ 60 Hz

VESA 1366 x 768 @ 60 Hz

Plug & Play

DDC 2B(Analog)

DDC 2B(Analog,Digital)

Power Consumption

On Mode : 17 W(Typ.)

Sleep Mode ≤ 0.5 W

Off Mode ≤ 0.5 W

Power Input

19 V

1.2 A

Type ADS-40SG-19-3 19025G, manufactured by SHENZHEN HONOR ELECTRONIC

or Type ADS-40FSG-19 19025GPG-1, manufactured by SHENZHEN HONOR ELECTRONIC

or Type ADS-40FSG-19 19025GPBR-1, manufactured by SHENZHEN HONOR ELECTRONIC

or Type ADS-40FSG-19 19025GPI-1,manufactured by SHENZHEN HONOR ELECTRONIC

or Type ADS-40FSG-19 19025GPCU-1, manufactured by SHENZHEN HONOR ELECTRONIC

or Type LCAP21, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE

or Type LCAP26-A, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE

or Type LCAP26-E, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE

or Type LCAP26-I, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE

or Type LCAP26-B, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE

AC-DC Adapter

Dimensions

(Width x Height x Depth)

With stand

Without stand

2.1 kg

44.9 cm x 17.3 cm x 35.7 cm

44.9 cm x 3.3 cm x 27.8 cm

Weight

tilt Range

-5° to 15°

environmental

operating temperature 10°C to 35 °C

conditions

operating Humidity

10 % to 80 % non-Condensing

storage temperature

-20°C to 60 °C

storage Humidity

5 % to 90 % non-Condensing

stand Base

Attached ( ), Detached (O)

Wall-outlet type

Power cord

Product specifications shown above may be changed without prior notice due to upgrade of product

functions.

SPECIFICATIONS

E2051S E2051T

Display

screen type

50.8 cm (20.0 inch) Flat Panel Active matrix-TFT LCD

Anti-Glare coating

Visible diagonal size: 50.8 cm

Pixel Pitch

0.2766 mm x 0.2766 mm (Pixel Pitch)

sync Input

Horizontal Frequency 30 kHz to 83 kHz (Automatic)

Vertical Frequency

Input Form

e2051s

56Hz to 75Hz (Automatic)

Separate Sync.

e2051t

Separate Sync. Digital

Video Input

signal Input

e2051s

15 pin D-SUB Connector

e2051t

15 pin D-SUB Connector /DVI-D Connector (Digital)

Input Form

e2051s

RGB Analog (0.7 Vp-p/ 75 ohm)

e2051t

RGB Analog (0.7 Vp-p/ 75 ohm), Digital

Resolution

Max

e2051s

D-SUB(Analog) : 1600 x 900 @ 60 Hz

D-SUB(Analog) / DVI(Digital): 1600 x 900 @ 60 Hz

VESA 1600 x 900 @ 60 Hz

e2051t

Recommend

e2051s

Plug & Play

DDC 2B(Analog)

e2051t

DDC 2B(Analog,Digital)

Power Consumption

On Mode : 21 W(Typ.)