JVC HV Z34L1 HV Z29L1 User Manual

COLOUR TELEVISION

Contents

Setting up your TV. . . . . . . . . . . . . . . . . . 3

TV buttons and functions. . . . . . . . . . . . . 6

Remote control buttons and functions. . . 8

Using the TV’s menu. . . . . . . . . . . . . . . 19

PICTURE menu . . . . . . . . . . . . . . . . . 20

FEATURES menu . . . . . . . . . . . . . . 21

SOUND menu. . . . . . . . . . . . . . . . . . . 24

FEATURES menu. . . . . . . . . . . . . . . . 26

SETUP menu . . . . . . . . . . . . . . . . . . . 29

Additional preparation . . . . . . . . . . . . . . 36

Troubleshooting. . . . . . . . . . . . . . . . . . . 40

Specifications . . . . . . . . . . . . . . . . . . . . 43

HV-Z34L1

HV-Z29V1

INSTRUCTIONS

LCT1457-001A-H

1003-CR-JMT

Setting up your TV

CAUTION

• Turn off all the equipment including the

TV before connecting anything.

1 Connecting the woofer unit

(only for HV-Z29V1)

1 Fitting the woofer unit

Align the projection on the base of the

woofer unit with the hole in the top of the

TV, and insert the connector into the

woofer terminal.

2 Connecting the supplied woofer

connector to the BASS SPEAKER

OUT terminal on the back of the TV

If the woofer unit is not connected, you

will not be able to enjoy the bass sound.

• Connect so that the lever is raised.

• When disconnecting the woofer

Lever

connector, do so while pushing the lever.

2 Connecting the aerial and VCR

• Aerial cable is not supplied. Use a

good quality 75-ohm coaxial cable.

• Read the manual that came with the

VCR before connecting.

Fig. A

If not connecting a VCR (see Fig. A):

Connect an aerial cable to the aerial socket

on this TV.

If connecting a VCR (see Fig. B):

Fig. B

1 Connect the aerial cable to the aerial

input socket on the VCR, and connect

the VCR and TV with another aerial

cable.

2 Connect the VCR’s VIDEO OUT (video

output) jack and the TV’s VIDEO jack

with a video cable.

To connect a VCR to the TV with an

S-VIDEO cable:

Connect the VCR’s S-VIDEO OUT (S-

VIDEO output) connector and TV’s S

connector with an S-VIDEO cable A,

instead of connecting with a video cable.

3 Connect the VCR’s AUDIO OUT (audio L/

R output) jacks and the TV’s AUDIO jacks

(L/MONO and R) with an audio cable.

• If the VCR’s audio output is in mono,

connect the VCR’s AUDIO OUT (audio

output) jack and the TV’s AUDIO L/

MONO jack with an audio cable.

Setting up your TV

3 Connecting the power cord

Connect the mains plug to the AC outlet.

4 Putting the batteries into the

remote control

Use two AA/R6 batteries.

Insert the batteries from the - end, making

sure the + and - polarities are correct.

• Follow the warnings printed on the

batteries.

HV-Z34L1

• If the remote control does not work

properly, replace the batteries.

• The batteries we supply are only for

setting up and testing your TV. Please

replace them as soon as necessary.

POWER

POWER lamp

Main power button

5 Making the initial settings

(SETUP TOUR)

When the TV is first turned on, it enters the

initial setting mode, and the JVC logo is

displayed.

HV-Z29V1

1 Press the main power button on the TV.

The TV is turned on, and the JVC logo

appears.

POWER

• If the POWER lamp on the TV lights

red and does not change to green,

your TV is in the standby mode. Press

the # button on the remote control to

turn the TV on.

POWER lamp

Main power button

• If the JVC logo does not appear, your

TV has already been turned before. In

this case, use the “LANGUAGE”,

“TELETEXT LANGUAGE” and “AUTO

PROGRAM” functions to make the

initial settings. For details, see

FAVORITE CHANNEL

SUB-P

TV/VIDEO

“SETUP menu” on page 29.

DISPLAY

BACK

2 Press the OK button on the remote

control.

SUB-P

CHANNEL

VOLUME

The LANGUAGE menu appears. You

can choose a language for the on-screen

language.

Setting up your TV

5 After the TV channels have been

3 Press the 6 buttons to choose

ENGLISH. Then press the OK button

on the remote contol.

stored in the programme numbers

(PR) list, the EDIT menu appears.

The TELETEXT LANGUAGE menu

appears. Set the teletext language group

that corresponds to the language of the

teletext program that you want to watch.

For details, see “TELETEXT

> EDIT

CH/CC

LANGUAGE” on page 34.

> TELETEXT LANGUAGE

MANUAL

GROUP-1

GROUP-2

GROUP-3

GROUP-4

MOVE

INSERT DELETE

D0038-EN

• You can proceed to edit the

programme numbers list using the

EDIT/MANUAL function. For details,

see “EDIT/MANUAL” on page 30.

• If a TV channel you want to view is not

stored in the programme numbers list,

you can register it using the MANUAL

function. For details, see “EDIT/

MANUAL” on page 30.

OSD-10-EN

4 Press the 6 buttons to choose a

group. Then press the OK button.

The AUTO PROGRAM function starts.

The TV channels you receive are

automatically stored in the PR

(programme numbers) LIST.

>> AUTO PROGRAM

• The AUTO PROGRAM function does

not store a TV channel to the

CH 28

14%

programme number 0 (AV).

• If you do not need to use the EDIT/

MANUAL function, press the OK

button to close the EDIT menu.

D0004-EN

• To stop the AUTO PROGRAM

function, press the OK button.

Now, setting up is complete. Please

enjoy your new JVC TV!

TV buttons and functions

Turn the main power on

Press the main power button 1.

The POWER lamp 2 lights red and your TV

is in the standby mode.

HV-Z34L1

To turn the main power off:

Press the main power button again. The

POWER lamp 2 goes off.

Turn the TV on from standby

mode

Press the CHANNEL-/+ buttons 5.

The POWER lamp 2 lights red to green

and your TV will be turned on.

POWER

• You can also turn on the TV by

pressing the TV/VIDEO button 3

while it is in standby mode.

Choose a TV channel

HV-Z29V1

Press the CHANNEL-/+ buttons 5.

Choose a VIDEO terminal

Press the TV/VIDEO button 3 or

CHANNEL-/+ buttons 5.

Adjust the volume

Press the VOLUME-/+ buttons 4.

The volume level indicator appears.

MENU button 6

Press to open the menu.

POWER

For details, see “Operation with the buttons

on the TV” on page 20.

Remote control sensor 7

HV-Z34L1

VIDEO-4 terminal 8

See page 36.

HV-Z29V1

Headphone jack 9

Connect the headphones with a stereo

mini-jack (3.5mm in diameter).

(Behind the cover)

OVER

L/MONO

CHANEL

VOLUME TV/VIDEO

EXIT

IN (VIDEO-4)

6 5 4 3

TV buttons and functions

VIDEO-1 terminal 0

Back of the TV

• See pages 3 and 36.

VIDEO-2 (COMPONENT)

terminal -

• See pages 33 and 36.

VIDEO-3 (COMPONENT)

terminal =

• See pages 33 and 36.

OUTPUT terminal ~

• See page 37.

Aerial socket !

Connect the aerial cable.

• See page 3.

AV COMPU LINK terminal @

• See page 38.

BASS SPEAKER OUT terminal

# (only for HV-Z29V1)

• See page 3.

Remote control buttons and functions

Turn the TV on from standby

mode

Press the # button.

The POWER lamp lights red to green and

your TV will be turned on.

• You can turn on the TV from the

standby mode by pressing the TV/

VIDEO button, the CHANNELp

buttons or the number buttons.

To turn the TV off:

Press the # button again.

The POWER lamp changes from green to

red and the TV enters standby mode.

RETURN+

To turn the TV on or off, set the PIP/TV/

DVD switch on the remote control to the

TV or PIP position and press the #

button.

FAVORITE CHANNEL

If the PIP/TV/DVD switch on the remote

control is set to the DVD position, the TV

will not be turned on or off even if the #

button is pressed.

SUB-P

TV/VIDEO

Choose a TV channel

Choose a programme number in which a

TV channel has been set.

DISPLAY

BACK

SUB-P

CHANNEL

VOLUME

Press the CHANNELp buttons or enter

the programme number (PR) with the

number buttons.

Example:

•

PR 6 → press 6

PR 12 → press 1 and 2

SOUND

CINEMA

MODE SURROUND BASS ZOOM

• You can select a channel from the PR

LIST. For details, see “DISPLAY

button” on page 11.

F.T/L

TOP MENU

• If you do not have a clear picture or no

colour appears, follow the operation

procedure “COLOUR SYSTEM” on

page 23.

STROBE

Remote control buttons and functions

ZOOM:

You can zoom up the Wide picture (16:9

aspect ratio) to fill the TV screen.

Adjust the volume

Press the VOLUME-/+ buttons.

Watch images from an

external device

Choose a VIDEO terminal to which the

external device has been connected.

• The left side and right side of the Wide

picture (16:9 aspect ratio) will be cut off.

16:9:

This mode converts a normal picture (4:3

aspect ratio) into a Wide picture (16:9

aspect ratio).

Press the TV/VIDEO button.

• You can choose a VIDEO terminal with

the CHANNELp buttons or from the

PR LIST.

To return to a TV channel:

Press the TV/VIDEO button, the

CHANNELp buttons or the number buttons.

l (Muting) button

Press the l (Muting) button to turn off the

volume. Pressing the l (Muting) button

again resumes the previous volume level.

• Use for picture with a 16:9 aspect ratio

that have been squeezed into a normal

picture (4:3 aspect ratio), you can

restore their original dimensions.

• When a 1125i signal is input, the 16:9

aspect ratio is chosen automatically.

ZOOM button

You can change the screen size according

to the picture aspect ratio. Choose the

optimum one from the following ZOOM

modes.

CINEMA SURROUND button

You can enjoy an enhanced sound for a

wider audience by using CINEMA

SURROUND function.

Press the CINEMA SURROUND button to

select one of CINEMA SURROUND modes.

1 Press the ZOOM button to display the

ZOOM menu.

• The ZOOM button works only in the

normal screen.

>> ZOOM

HIGH/LOW:

When you listen to the stereo sound, please

select HIGH or LOW mode.

REGULAR

ZOOM

16:9

You can enjoy the sound for a wider

audience similar to the experience at the

theatre.

D0017-EN

When you combine the functions of SOUND

MODE, SUPER BASS and DIGITAL BBE,

you can enjoy more powerful sound.

• In case that you setting up the

CINEMA SURROUND function to

HIGH mode, there may be slight

volume distortion. In case that occurs,

please switch the HIGH mode to LOW

mode, the effect of CINEMA

2 Press the 6 buttons to choose a

ZOOM mode. Then press the OK button.

REGULAR:

Use to view a normal picture (4:3 aspect

ratio) as its original size is.

SURROUND functions will be less

noticeable, however, the volume

distortion will be corrected.

Remote control buttons and functions

MONO:

RETURN+ button

Select the MONO mode, when you listen to

the mono sound.

You can enjoy the sound for a wider

The RETURN+ button has two functions;

the RETURN+ function and the RETURN

function. If a channel has been registered

as the “Return Channel”, the RETURN+

function operates. If there is no setting for

the “Return Channel”, the RETURN function

operates.

audience similar to stereo sound.

OFF:

The CINEMA SURROUND function

switches off.

SOUND MODE button

RETURN+ function

You can select the SOUND MODE of you

liking from 4 types of sound modes to fully

enjoy the sound of your TV.

By registering a channel you frequently

view as the “Return Channel”, you can

select that channel at any time simply by

pressing the RETURN+ button.

Press the SOUND MODE button to select

one of sound modes.

DYNAMIC:

Dynamic sound is created by enhancing

To register a TV channel as the “Return

Channel”:

high and low tones.

You can get the 3D effect by using the

CINEMA SURROUND function in this mode.

Choose the Programme number to which

the channel you want to register has been

set, and press the RETURN+ button and

hold for more than 3 seconds continuously.

“RETURN PLUS PROGRAMMED!” is

displayed and the registration is completed.

MUSIC:

The mode suitable for music programmes.

Enjoy a concert hall-like atmosphere.

Combination with the CINEMA SURROUND

function will bring wider range sound.

To cancel a TV channel registered as the

“Return Channel”:

NEWS:

While viewing any TV channel, press the

RETURN+ button and hold for more than 3

seconds continuously. “RETURN PLUS

CANCELED!” is displayed and the

registration is cancelled.

The mode suitable for news programmes

makes the voice of the newscaster or the

like easier to hear.

USER:

Save your own sound setting to memory

with this mode.

The USER setting is performed with the

“SOUND MODE” menu (see page 25).

• When you turn off the TV, the

registration for the “Return Channel” is

cancelled.

• If you want to view the “Return

Channel” and another TV channel

alternately, first choose a channel

other than the “Return Channel”. And

then press the RETURN+ button to

change the channel to the “Return

Channel” In this way, you can view two

channels alternately by pressing the

RETURN+ button.

BASS button

You can choose the SUPER BASS mode

which emphasizes the bass sound.

Press tge BASS button to select one of

SUPER BASS modes.

You can choose HIGH, MID or LOW.

Choosing LOW will reduce the bass sound

and choosing HIGH will increase the bass

sound.

Remote control buttons and functions

RETURN function

Choose a TV channel or a

VIDEO terminal

1 Press the DISPLAY button to display

the PR LIST.

The TV temporarily memorises the TV

channel that was chosen right before the

current TV channel as the “Last Channel”.

By pressing the RETURN+ button, you can

alternately view the current TV channel and

the “Last Channel”.

2 Press the 6 and 5 buttons to

choose a programme number or

VIDEO terminal.

• If you want to view two channels

alternately by using the RETURN

function, first choose one TV channel

and then choose the other TV channel

with the Number buttons. If you choose

the TV channel without using the

Number buttons, there are cases

where a channel other than the one

you first chose is registered as the

“Last Channel”.

Then press the OK button.

• For programme numbers with the

CHANNEL GUARD function set, the n

(CHANNEL GUARD) mark is

displayed next to the programme

number in the PR LIST.

• The VIDEO terminals are registered

after the programme number PR99.

• The AV channel (channel number 0) in

the PR LIST will be chosen only if you

connect the VCR to the TV with an

aerial cable without connecting a video

cable.

DISPLAY button

You can display the PR LIST, programme

number or VIDEO terminal number on the

screen.

Favorite channel registration

You can register your favorite TV channels

with the colour buttons (Red, Green, Yellow

and Blue). After registration you can recall

the favorite channel by pressing the colour

button.

Press the DISPLAY button.

Press the DISPLAY button changes the

display as follows:

PR LIST

1 In the normal screen, choose a TV

channel (PR01-99) you want to

Programme or VIDEO

terminal number

For detailed operation, see “Choose a

TV channel” on page 8.

No indication

2 Press and hold a colour button for 3

seconds or more.

-10

+10

Then “FAVORITE CH PROGRAMMED”

appears on the screen and the current

channel is registered.

D0011-EN

Remote control buttons and functions

• If the chosen channel is already

registered as the favorite channel,

when a colour button is pressed, the

registered colour button icon appears

on the top right of the screen.

• You cannot register in the Text mode,

or while multiple screens, such as PIP

(picture in picture) are displayed.

• Also you cannot register if the chosen

channel is guarded with the CHANNEL

GUARD function and the screen is

blue, or if an on-screen menu is

displayed.

„ Showing the favorite channels

Press the DISPLAY button to display the

PR LIST.

You can see the favorite channel that has

the registered colour button icon at the right

of the channel number.

PR LIST

• Starting the AUTO PROGRAM deletes

the registered favorite channel.

-10

+10

D0011-EN

„ Recalling the favorite channel

Press the colour button, then the registered

favorite channel will be displayed.

Twin and PIP (picture in

picture) function

You can view two pictures (Main picture and

sub picture). Two different TV programmes

can be watched at the same time or a TV

programme and a video programme from

an externaldevice can be watched at the

same time.

• You cannot recall the favorite channel

in the Text mode, Menu mode where

an on-screen menu is displayed.

• The picture effect dedicated for the

colour button applies. For details, see

“Setting the picture effect” below:

„ Setting the picture effect

Each colour button has a dedicated picture

effect. When you choose a favorite channel

with a colour button, the dedicated picture

effect is used. When shipped, the factory

set picture effect is used for this purpose.

However, you can set this picture effect as

required. For details, see “FAVORITE

SETTING” on page 28.

Operate with the PIP/TV/DVD switch set

to the PIP position.

Twin mode

Press

Each time it is pressed the mode changes

as shown below.

Normal screen

Twin mode

Sub

Main

Remote control buttons and functions

PIP (picture in picture) mode

Press

Each time it is pressed the mode changes

as shown below.

„ Listening to the sound of the

sub-picture:

You can listen to the sound of the sub-

picture with the headphones while listening

to the sound of the main-picture from the TV

speakers.

Normal screen

PIP mode

For details, see “HEADPHONE VOLUME”

on page 25.

Sub

• The sub-picture sound is monaural.

Main

To return to the normal screen:

„ TV channel selection

For the main picture:

Choose a channel using the CHANNELp

buttons or the number buttons.

Press the

again, or press the

BACK button.

For the sub picture:

Choose a channel using the SUB-P6

buttons.

• The

and

buttons do not work in

the Text mode.

• Twin and PIP functions do not work for

a picture of 1125i signal.

„ Input source selection (TV,

• A picture of 625p or 525p signal

cannot be displayed as the sub-

picture.

VIDEO-1, -2, -3 or -4)

For the main picture:

Press the TV/VIDEO button.

Each time you press the button, the input

source changes as follows (the one used for

the sub picture will be skipped):

VIDEO-1 → VIDEO-2 → VIDEO-3 →

VIDEO-4 → TV

Pay attention to the following.

- When the VIDEO-2 or VIDEO-3

picture is a picture of 625p or 525p

signal, you cannot choose VIDEO-2

or VIDEO-3 with the SUB-P6

buttons.

For the sub picture:

- When the VIDEO-2 or VIDEO-3

picture signal is changed to 625p,

525p or 1125i signal while the

VIDEO-2 or VIDEO-3 picture is

displayed as the sub-picture, the

Twin or PIP modes is cancelled.

Press the

(Input) button.

Each time you press the button, the input

source changes as follow (the one used for

the main picture will be skipped):

VIDEO-1 → VIDEO-2 → VIDEO-3 →

VIDEO-4 → TV

„ Swapping the pictures

Press the

(Swap) button.

Each time you press the button, the main

picture and the sub picture will be swapped.

• The pictures cannot be swapped when

a picture of 625p or 525p signal from

VIDEO-2 or VIDEO-3 is being

displayed as the main picture.

Remote control buttons and functions

3 Choose the screen you want to view

The picture you choose changes to a

moving picture.

„ Changing the sub picture

position (in PIP mode only)

You can position the sub picture to one of

corners of the main picture.

9 pictures multi:

Choose by pressing 56.

Press the

(Position) button.

5 pictures multi:

Choose by pressing 6.

Each time you press the button, the sub

picture moves clockwise (lower right →

lower left → upper left → upper right).

4 Press the OK button

The multi-pictures disappears and the

chosen picture appears.

„ Setting the colour system of

the sub picture

Changing the multi-picture mode:

See “MULTI” on page 24.

You can choose the colour system of the

sub picture.

Cancelling the multi-pictures

Press the BACK button, CHANNELp

buttons, the number buttons or OK button.

The setting is performed with the “COLOUR

SYSTEM” menu (see page 23) when in the

Twin mode or PIP mode.

•

You can also enter this mode while in the

Twin mode, but not in the Text mode.

Multi-picture function

You can display multi-pictures that enable you

to easily find a program you want to view.

• Pictures will appear in the assigned

order in the PR LIST (PR01-99).

• The guarded channel with the

CHANNEL GUARD function will be

skipped and will not be displayed.

• Pictures from external devices cannot

be displayed in the 9-pictures multi

mode.

• In the 5-pictures multi mode, the

picture from external devices can only

be displayed as the main picture.

• In the 5 pictures multi mode, 1125i

signal cannot be displayed as the main

picture.

1 Set the PIP/TV/DVD switch to the PIP

position

2 Press the X button to display multi-

pictures

The channels are displayed in the

channel number order.

The multi-pictures will appear in one of

the two multi-picture modes.

9 pictures multi:

Still pictures

• The RETURN+ button is disabled in

the 9 pictures multi mode.

• In the multi-picture mode, the menu

cannot be displayed.

Moving picture

5 pictures multi:

• In the 5 pictures multi mode, the sound

in the moving picture can be listened

through the headphone.

Still pictures

Main picture

Moving picture

• To display the next multi-pictures,

press the X button.

Remote control buttons and functions

2 Press the STROBE button.

Eight consecutive still pictures which are

captured at intervals of about 0.2 second

are displayed in the order of “1” to “9”.

(These numbers are not actually

displayed.)

Freeze function

1 Set the PIP/TV/DVD switch to the PIP

position.

2 Press the

(Freeze) button.

Still picture is captured and displayed on

the right side of the screen. On the left,

the moving picture is displayed.

While watching a picture, you can

capture a still picture you want. The

captured still picture and the moving

picture are displayed at a time. (They are

the pictures of the same source.)

Still

picture

Moving

picture

To return to the normal screen:

Press the STROBE button again or press

the BACK button, the CHANNEL p

buttons or the number buttons.

• If signal level of the main picture is

weak, the still images become

abnormal.

To return to the normal screen:

Press the (Freeze) button again or

press the BACK button, the CHANNEL p

buttons or the number buttons.

• The

(Freeze) button do not work in

• The STROBE button do not work in the

Text mode, Twin mode, or PIP mode.

• The STROBE function does not work

for picture of 1125i signal.

• The menu cannot be displayed in the

STROBE mode.

the Text mode, Twin mode, or PIP

mode.

• The FREEZE function does not work

for picture of 1125i signal.

Strobe function

You can display eight consecutive still

pictures and one moving picture at a time.

(They are the pictures of the same source.)

1 Set the PIP/TV/DVD switch to the PIP

position.

Remote control buttons and functions

Operating a JVC brand DVD

player

You can operate a JVC brand DVD player.

Pressing the button having the same

appearance as the original remote control

button of a device makes the function work

in the same way as the original remote

control.

Viewing a teletext programme

1 Choose a TV channel with a teletext

broadcast.

2 Set the PIP/TV/DVD switch to the TV

position.

PIP

DVD

F.T/L

TOP MENU

3 Press P (Text) button to display the

teletext.

STROBE

Pressing P (Text) button changes the

mode as follows:

1 Set the PIP//TV/DVD Switch to the

DVD position

When you are operating the DVD player,

set the switch to the DVD position.

• You can turn the DVD player on or off

with the # (Standby) button.

TV and

Text mode

TV mode

• You can also press the MENU or TOP

MENU button and display the DVD

disc menu screen, and then operate by

pressing the 56 buttons.

Text mode

4 Choose a teletext page by pressing

the CHANNEL p buttons, number

buttons or colour buttons.

2 Press the DVD Control Button to

control your DVD player

• If your device is not made by JVC,

these buttons cannot be used.

• Even if your device is made by JVC,

some of these buttons or any one of

the buttons may not work, depending

on the device.

To return to the TV mode:

Press the P (Text), BACK or TV/VIDEO

button.

• If you have trouble receiving teletext

broadcasts, consult your local dealer

or the broadcast station.

• In the Text mode, the ZOOM mode is

fixed to the REGULAR mode.

• No menu operations are possible

when viewing a teletext programme.

• If characters on a teletext programme

do not appear properly, change the

TELETEXT LANGUAGE setting. For

details, see “TELETEXT LANGUAGE”

on page 34.

You cannot turn the TV on or off when the

PIP//TV/DVD switch is set to the DVD

position. When you turn the TV on or off,

set the PIP/TV/DVD switch to the TV or

PIP position.

Remote control buttons and functions

3 Press the

(Cancel) button to

return to a teletext page when the

page number is on the screen.

• You cannot return to the TV mode with

(Hold) button

You can hold a teletext page on the screen

for as long as you want, even while several

other teletext pages are being received.

the

(Cancel) button.

Press the

(Hold) button.

Sub-page

The (hold) are displayed at the top left

of the screen.

Some teletext pages include sub-pages that

are automatically displayed.

To cancel the Hold function:

1 Choose a teletext page that includes

sub-pages.

Press the

(Hold) button again.

Sub-page numbers that can be viewed

are automatically displayed at the top of

the screen.

(Reveal) button

Some teletext pages include hidden text

(such as answers to a quiz).

You can display the hidden text.

2 Press the 5 buttons to choose a

sub-page number.

Each time you press the

(Reveal)

button, text is hidden or revealed.

(Size) button

You can double the height of teletext

display.

Press the

(Size) button.

(Index) button

You can return to the index page instantly.

Press the (Index) button.

• In the List mode, you can return to the

page number displayed in the lower

left area of the screen.

(Cancel) button

You can search for a teletext page while

watching TV.

1 Press the number button to enter a

page number, or press the colour

button.

The TV searches for a teletext page.

2 Press the

(Cancel) button.

The TV programme appears. When the

TV finds the teletext page, its page

number appears in the upper left of the

screen.

Remote control buttons and functions

Using the List mode

You can store the numbers of your favorite

teletext pages in memory and call them up

quickly using the colour buttons.

To store the page numbers:

1 Press the F.T/L button to engage the

List mode.

The stored page numbers are displayed

at the bottom of the screen.

2 Press a colour button to choose a

position. Then press the number

buttons to enter the page number.

3 Press and hold down the

button.

(Store)

The four page numbers blink white to

indicate that they are stored in memory.

To call up a stored page:

1 Press the F.T/L button to engage the

List mode.

2 Press a colour button to which a page

has been assigned.

To exit the List mode:

Press the F.T/L button again.

Using the TV’s menu

This TV has a number of functions you can operate using menus.

To fully utilize all your TV’s functions, you need to understand the basic menu operating

techniques fully.

Buttons used to operate the menus

Types of menu

PICTURE menu

RETURN+

Choose to set the screen set-

tings.

D0106

D0107

D0108

FAVORITE CHANNEL

TV/VIDEO

SOUND menu

Choose to set the sound set-

tings.

SUB-P

TV/VIDEO

FEATURES menu

Choose to set the sleep timer

and child lock settings.

DISPLAY

BACK

SUB-P

CHANNEL

VOLUME

SET UP menu

1 Press the H button to display the

Choose to edit the channels

or set the display language

settings.

menu bar

D0109

PICTURE

The menu guide area can be made to

appear and disappear for some menus.

While the menu is displayed, press the

DISPLAY button to change between the

guide area being displayed and not

displayed.

D0105-EN

2 Press the 5 buttons to choose the

menu you want to use and then press

the a button

PICTURE

D1105-EN

Chosen

menu name

>> ZOOM

REGULAR

ZOOM

16:9

3 Press the 6 buttons to choose the

item to be set, press the 5 buttons

to set the item, and then press the a

button

D0017-EN

Guide area

If there are sub-menus, use the 7

buttons to operate them.

• Press the b button to return to

the previous menu.

• Press the TV/VIDEO or MENU button

to exit from the menu.

>> ZOOM

REGULAR

ZOOM

16:9

D1017-EN

• The guide area for some menus will

still be displayed even if the DISPLAY

button is pressed. This is not a

malfunction.

Using the TV’s menu

Operation with the buttons on the

PICTURE menu

PICTURE

You can also operate the menus using the

buttons on the front panel of the TV.

STANDARD

PICTURE MODE

CONTRAST

BRIGHT

SHARP

COLOUR

TINT

WHITE BALANCE

FEATURES

TV/VIDEO

button

buttons buttons

button

COOL

RESET

D0014-EN

„ PICTURE MODE

You can choose one of three PICTURE

MODEs to adjust the picture settings

automatically.

CHANNEL

VOLUME TV/VIDEO

EXIT

• The OK button acts as the MENU

button when the menu bar is not

displayed, and as the OK button when

the menu bar is displayed.

• Press the TV/VIDEO button to exit

from the menu.

BRIGHT:

Heightens contrast and sharpness.

STANDARD:

Standardizes picture adjustment.

SOFT:

Softens contrast and sharpness.

„ Adjusting the picture

You can change the picture settings of each

picture mode, as you like. The picture

settings changed are stored in the picture

mode.

CONTRAST

You can adjust the picture contrast.

2 : lower

3 : higher

BRIGHT

You can adjust the picture brightness.

2 : darker

3 : brighter

SHARP

You can adjust the picture sharpness.

2 : softer

3 : sharper

COLOUR

You can adjust the picture colour.

2 : lighter

3 : deeper

Using the TV’s menu

TINT

FEATURES menu

Choose FEATURES in the “PICTURE”

menu and press the a or 3 button to

display the sub-menu.

You can adjust the picture tint.

2 : reddish

3 : greenish

• You can change the TINT setting

(picture tint) only when the colour

system is NTSC 3.58 or NTSC 4.43.

> FEATURES

DIGITAL VNR

Super DigiPure

PULL DOWN

Colour DigiPure

COLOUR SYSTEM

ZOOM

AUTO(LOW)

AUTO

To return to the default settings in each

PICTURE MODE:

Press the blue button. This will return the

picture settings in the currently chosen

PICTURE MODE to the default settings,

and stores them in the PICTURE MODE

again.

MULTI

D1015-EN

„ DIGITAL VNR

„ WHITE BALANCE

The DIGITAL VNR function cuts down the

amount of noise in the original picture.

You can choose from the four DIGITAL

VNR function settings of AUTO(LOW),

AUTO(HIGH), MIN and MAX.

You can select one of three WHITE

BALANCE modes (three tones of white) to

adjust the white balance of the picture.

Since white is the colour which is used as a

reference for all the other colours, changing

the WHITE BALANCE mode affects the

appearance of all the other colours on the

screen.

AUTO(LOW)/AUTO(HIGH):

The TV will automatically adjust the level of

the DIGITAL VNR effect to match the

amount of noise in the picture, giving you

the best possible picture.

COOL:

A bluish white. Using this mode when

watching bright pictures allows you to enjoy

a more vivid and bright picture.

• If you set the DIGITAL VNR effect too

high it can make the picture less

sharp. It is recommended to use the

AUTO(LOW) setting if you can. If you

set the DIGITAL VNR function to

AUTO(LOW)but still notice some

noise, change the setting from

MID:

The normal white colour.

WARM:

A radish white. Using this mode when

watching films allows you to enjoy colours

that are characteristic of films.

AUTO(LOW) to AUTO(HIGH).

MIN:

The level of the DIGITAL VNR effect is set

to the minimum. If you set the DIGITAL

VNR function to AUTO(LOW) but feel that

the sharpness of the original picture has not

been reproduced fully, change the setting

from AUTO(LOW) to MIN.

• The MIN setting is not suitable for low-

quality pictures which contain a lot of

noise.

Using the TV’s menu

MAX:

MIN:

The level of the DIGITAL VNR effect is set

to the maximum. If you set the DIGITAL

VNR function to AUTO(HIGH) but still notice

some noise, change the setting from

AUTO(HIGH) to MAX.

The level of DigiPure effect is set to the

minimum. When you set the Super DigiPure

function to AUTO and notice some noise,

change the setting from AUTO to MIN.

• The MIN setting is not suitable for

high-quality pictures which contain

very little noise.

• The MAX setting is not suitable for

high-quality pictures which contain

very little noise.

MAX:

The level of DigiPure effect is set to the

maximum. If you set the Super DigiPure

function to AUTO but feel that the original

picture quality has not been reproduced

fully, change the setting from AUTO to

MAX.

„ Super DigiPure

The Super DigiPure function uses the latest

in digital technology to give you a natural-

looking picture. The Super DigiPure

function includes the following two

functions.

• The MAX setting is not suitable for

low-quality pictures which contain a lot

of noise.

DigiPure function:

This function helps to create a natural-

looking picture by eliminating unnecessary

edges from high-contrast and crisp images.

For images with low-contrast, edges are

added to produce a sharper, more detailed

picture.

OFF:

The Super DigiPure function is turned off.

„ PULL DOWN

The PULL DOWN function displays a

cinema film picture more smoothly and

naturally on the screen.

You can choose from the three DigiPure

function settings of AUTO, MIN and MAX.

• If you set the DigiPure effect too high

on a low-quality picture that contains a

lot of noise, this may actually make

the noise worse. We recommend you

use the AUTO setting if you can.

AUTO:

This function is turned on. Normally keep

this function set to AUTO.

ON :

This function is turned on.

Picture motion compensation function:

This function displays fast-moving pictures

(for example, the players or ball in a football

game) more smoothly and naturally on the

screen.

OFF:

This function is turned off.

• The motion may appear unnatural

when viewing images with the NTSC

colour system. To make the motion

smoother, switch the PULL DOWN

function from AUTO or ON to OFF.

• The effect level of the picture motion

compensation function cannot be

changed. The effect level is the same

no matter which of the AUTO, MIN or

MAX settings is used.

AUTO:

The TV will automatically adjust the level of

the DigiPure effect to match the amount of

noise in the picture, giving the best possible

picture.

Using the TV’s menu

SECAM:

SECAM system

„ Colour DigiPure

Makes the colour outline stand out and

increases the sharpness giving a clearer

picture.

NTSC 3.58:

NTSC 3.58 MHz system

ON:

NTSC 4.43:

NTSC 4.43 MHz system

Colour DigiPure works. Normally use with

this function turned on.

AUTO:

OFF:

This function detects a colour system

Colour DigiPure doesn’t work. This gives a

less clear picture than when this function is

turned on.

from the input signal.

• The AUTO function may not function

properly if you have poor signal

quality. If the picture is abnormal in

the AUTO function, choose another

colour system manually.

„ COLOUR SYSTEM

The colour system is chosen automatically.

However, if the picture is not clear or no

colour appears, choose the colour system

manually.

For colour system in your country or

region, refer to the table below:

Area

Country or Region

System

1 Choose COLOUR SYSTEM. Then

press the a or 3 button

Bahrain, Kuwait, Oman,

Qatar, United Arab Emirates,

Yemen, etc.

The sub-menu of the COLOUR SYSTEM

function appears.

PAL

Indonesia, Malaysia,

Singapore, Thailand, India,

etc.

China, Vietnam, etc.

Hong Kong, etc.

>> COLOUR SYSTEM

Asia,

Middle

East

PAL

MAIN

SUB

PAL

AUTO

Islamic Republic of Iran,

Lebanon, Saudi Arabia, etc.

SECAM

Philippines, Taiwan,

Myanmar, etc.

NTSC

Russia, etc.

SECAM

D0016-EN

Czech Republic, Poland, etc. PAL

2 Press the 5 buttons to choose

Europe

Germany, Holland, Belgium,

PAL

MAIN or SUB

etc.

UK, etc.

MAIN:

Oceania Australia, New Zealand, etc. PAL

Republic of South Africa, etc. PAL

You can change the colour system of the

main-picture.

Africa

Nigeria, etc.

PAL

SUB:

Egypt, Morocco, etc.

SECAM

You can change the colour system of the

sub-picture.

• Choose MAIN when a sub-picture is

not displayed.

3 Press the 6 buttons to choose the

appropriate colour system. Then

press the a button

PAL:

PAL system

Using the TV’s menu

„ ZOOM

SOUND menu

You can change the screen size according

to the picture aspect ratio. Choose the

optimum one from three ZOOM modes.

SOUND

STEREO/

SOUND MODE

BALANCE

HEADPHONE VOLUME

CINEMA SURROUND

SUPER BASS

MONO

1 Choose ZOOM, then press the OK or

MONO

LOW

3 button.

BBE DIGITAL

>> ZOOM

OSD-3-EN

REGULAR

ZOOM

16:9

• Functions in the “SOUND” menu other

than “HEADPHONE VOLUME” work

for the TV speakers. They do not work

for the sound from the headphones.

• When the headphones are connected

and only one screen is displayed,

“STEREO/I•II” and “HEADPHONE

VOLUME” can be used.

D0017-EN

2 Press the 6 buttons to choose a

ZOOM mode. Then press the OK

button.

• You can choose a ZOOM mode from

REGULAR, ZOOM or 16:9 modes. For

details, see “ZOOM button” on page 9.

„ STEREO / I•II

When you are viewing a bilingual broadcast

programme, you can choose the sound

from Bilingual I (sub I) or Bilingual II (sub II).

When the stereo broadcasting is received

poorly, you can change from stereo to mono

sound so that you can hear the broadcast

more clearly and easily.

„ MULTI

Choosing the number of pictures for the

Multi-picture function.

1 Choose MULTI, then press the OK or

3 button.

s : Stereo sound

>> MULTI

: mono sound

: Bilingual I (sub I)

: Bilingual II (sub II)

OSD-2-EN

MONO: Cancels the Multi Sound function,

and the sound becomes monaural.

• The sound mode you can choose

differs depending on the TV

programme.

2 Press the 5 buttons to choose the

number of pictures. Then press the

OK button.

• This function does not work in the

VIDEO modes.

Using the TV’s menu

„ SOUND MODE

„ HEADPHONE VOLUME

SOUND MODE USER.

Adjust the volume of the sub-picture sound

which is heard through the headphones

when set to Twin mode, PIP mode or 5

pictures multi.

1 Choose SOUND MODE, then press the

OK or 3 button.

2 :Reduce volume

3 :Increase volume

The “SOUND MODE“ menu appears.

• When not set to Twin mode or PIP

mode, the headphone volume is

adjusted with the r q (volume)

buttons.

> SOUND MODE

NEWS

„ CINEMA SURROUND

You can enjoy Surround sound with a “live”

effect by using the CINEMA SURROUND

function.

120Hz

500Hz

1.5kHz

5kHz

10kHz

SOUND MODE

• You can choose a CINEMA SURROUND

mode from HIGH, LOW, MONO and OFF

modes. For details, see “CINEMA

SURROUND button” on page 9.

• You can also operate the CINEMA

SURROUND function with the

CINEMA SURROUND button. For

details, see “CINEMA SURROUND

button” on page 9.

OSD4-EN

2 Press the red button and choose your

preferred SOUND MODE.

3 Press the 5 buttons and choose the

frequency to adjust, then press the

6 buttons and adjust the frequency.

• The adjusted frequency is registered

to USER.

„ SUPER BASS

• When DYNAMIC, MUSIC, or NEWS is

chosen and the frequency is adjusted,

the SOUND MODE automatically

changes to USER.

• Adjust the other frequencies

according to your preference.

• After adjusting the frequencies in step

3, pressing the blue button will return

to the SOUND MODE pattern chosen

in step 2.

You can choose the SUPER BASS mode

which emphasizes the bass sound.

• You can choose HIGH, MID or LOW.

Choosing LOW will reduce the bass

sound and choosing HIGH will

increase the bass sound.

• You can also operate the SUPER

BASS function with the BASS button.

For details, see “BASS button” on

page 10.

• You can choose a SOUND MODE

function with the SOUND MODE

button. For details, see “SOUND

MODE button” on page 10.

„ BBE DIGITAL

You can use the BBE DIGITAL function to

enjoy easy-to-listen sound that is faithful to

the original sound recorded.

„ BALANCE

• You can choose ON or OFF.

• Licensed by BBE Sound, Inc. BBE is a

registered trademark of BBE Sound, Inc.

You can adjust the volume balance

between the left and right speakers.

2 : turn the left speaker’s volume level up.

3 : turn the right speaker’s volume level up.

Using the TV’s menu

FEATURES menu

FEATURES

„ CHANNEL GUARD

When there is a TV channel you do not

want your children to watch, you can lock

out the channel. Even when a child chooses

a programme number for a locked out

channel the screen will change to blue and

display n so the channel cannot be viewed.

SLEEP TIMER

CHANNEL GUARD

APPEARANCE

BLUE BACK

CHILD LOCK

AUTO SHUTOFF

FAVORITE SETTING

TYPE A

OFF

OSD-5-EN

To set this function:

1 Choose CHANNEL GUARD, then

press the number 0 button.

„ SLEEP TIMER

You can set the TV to automatically turn off

after a set time.

> SET ID NO.

0040

1 Choose SLEEP TIMER, then press the

OK or 3 button.

> SLEEP TIMER

D0025-EN

120

2 Set the ID number you want.

OFF

To choose a number:

Press the 6 buttons.

To move a cursor:

D0024-EN

Press the 5 buttons.

2 Press the 5 buttons to set the

period of time.

3 Press the OK button.

>> CHANNEL GUARD

The TV begins count down from the set

time.

• You can set the period of time a

maximum of 120 minutes (2 hours) in

10 minute steps.

To cancel this function:

• Press the 2 button to set a period of

time to “OFF”.

GUARD

D0026-EN

3 Press the OK button to complete the

setting.

4 Press the 6 buttons to choose a TV

channel.

The menu disappears.

• One minute before this function turns

off the TV, “GOOD NIGHT!” appears.

• This function cannot be used to turn off

the TV’s main power.

• When this function is on, you can

display the SLEEP TIMER menu again

to confirm or change the remaining

time.

• The TV shows the TV programme

which the chosen TV channel is now

broadcasting.

5 Press the blue button to set this

function to the TV channel.

n (CHANNEL GUARD) appears and the

TV channel is locked.

Using the TV’s menu

To cancel this function:

„ BLUE BACK

Press the blue button again.

n (CHANNEL GUARD) disappears and

the lock is released.

You can set the TV to automatically change

to a blue screen and mute the sound if the

signal is weak or absent, or when there is

no input from an external device.

6 Press the OK button to complete the

setting.

ON:

The menu disappears.

This function is turned on.

To view a locked TV channel:

OFF:

1 Choose a programme number in

which a TV channel locked with the

number buttons or PR LIST.

This function is turned off.

„ CHILD LOCK

The screen changes to blue and the n

(CHANNEL GUARD) appears.

You can disable the front control buttons of

the TV. When this function is set to ON, the

TV can be operated only by using the

remote control.

D0027-EN

• You cannot choose a locked TV channel

with the CHANNEL p buttons.

Use this function to prevent children from

operating the TV at their own discretion

(without parent consent).

2 Press the DISPLAY button to display

“ID NO.” (ID number input screen).

ON:

This function is turned on.

OFF:

ID NO.

D0028-EN

This function is turned off.

Turning the power off with the main power

button cancels the CHILD LOCK.

3 Press the number buttons to enter the

ID number.

The lock is temporarily released so you

can view the TV channel.

„ AUTO SHUTOFF

You can set the power to turn off if no signal

is received and no operation is performed

for about 15 minutes or longer after the end

of a broadcast.

If you have forgotten the ID number:

Perform step 1 of “To set this function:” on

page 26. After confirming the ID number,

press the TV/VIDEO button to exit the menu.

ON:

• When you would like to cancel the

CHANNEL GUARD function, you must

perform the operation “To set this

function” again.

This function is turned on.

OFF:

This function is turned off.

• The AUTO SHUTOFF function does

not turn off the TV’s main power.

• The AUTO SHUTOFF will not work for

a VIDEO mode.

„ APPEARANCE

Press the 5 button and choose the

format in which the channel number is

displayed from the three types: TYPE A,

TYPE B and TYPE C.

Using the TV’s menu

• For details of each item, see

“PICTURE MODE” on page 20,

“DIGITAL VNR” on page 21, “WHITE

BALANCE” on page 21, “Super

DigiPure” on page 22.

„ FAVORITE SETTING

You can set a dedicated picture effect for

the favorite channels registered to the

colour buttons (Red, Green, Yellow and

Blue). For favorite channel registration, see

“Favorite channel registration” on page 11.

Item

Options

1 Choose FAVORITE SETTING, then

PICTURE MODE BRIGHT*, STANDARD,

SOFT

press the OK or 3 button.

DIGITAL VNR

AUTO (LOW)*, AUTO

(HIGH), MIN, MAX

> FAVORITE SETTING

FAVORITE CH SETTING

VIDEO SETTING

WHITE

BALANCE

COOL, MID*, WARM

OSD-6-EN

Super DigiPure AUTO*, MAX, OFF, MIN

PICTURE

EFFECT

ON*:

2 Choose FAVORITE CH SETTING, then

Above picture effect

applies to the chosen

favorite channel.

OFF:

press OK or 3 button.

>> FAVORITE CH SETTING

FAVORITE CHANNEL

RP 06

No picture effect applies.

PICTURE MODE

DIGITAL VNR

WHITE BALANCE

Super DigiPure

PICTURE ADJUST

BRIGHT

AUTO(LOW)

COOL

OFF

*: When shipped

• Pressing the blue button returns each

setting back to initial setting and cancels

the favorite channel registration.

RESET

OSD-7-EN

5 Press the OK button to complete the

setting.

3 Press the 6 button to choose

FAVORITE CHANNEL, then press the

5 button to choose the registered

favorite channel.

„ VIDEO SETTING

You can set a dedicated picture effect for

the video inputs, VIDEO-1 to -4.

Each time you press the 5 button, the

colour button icon (Red, Green, Yellow

or Blue) of the registered favorite

channel and its channel number (e.g.

PR1) appear.

1 Choose FAVORITE SETTING, then

press the OK or 3 button.

2 Choose VIDEO SETTING, then press

the OK or 3 button.

4 Set the picture effect.

>> VIDEO SETTING

Press the 6 button to choose an item

listed in the following table and press the

5 button to choose one of options.

• As explained in the table, if PICTURE

EFFECT is set to OFF, the dedicated

picture effect for the favorite channel is

not used. In this case, normal picture

effect is used.

VIDEO

VIDEO-1

BRIGHT

AUTO(LOW)

COOL

AUTO

PICTURE MODE

DIGITAL VNR

WHITE BALANCE

Super DigiPure

PICTURE ADJUST

RESET

OSD-8-EN

Using the TV’s menu

3 Press the 6 button to choose

VIDEO, then press the 5 button to

choose one of video inputs, VIDEO-1

to -4.

SETUP menu

SET UP

AUTO PROGRAM

EDIT/MANUAL

LANGUAGE

4 Set the picture effect.

PICTURE TILT

VIDEO-2 SETTING

VIDEO-3 SETTING

AI VOLUME

COMPONENT

Press the 6 button to choose an item

listed in the following table and press the

5 button to choose one of options.

• As explained in the table, if PICTURE

EFFECT is set to OFF, the dedicated

picture effect for the video inputs is not

used. In this case, normal picture

effect is used.

TELETEXT LANGUAGE

OSD-9-EN

„ AUTO PROGRAM

You can automatically register the TV

channels which can be received well at your

residence in the TV’s programme numbers

by performing the following.

Item

Options

PICTURE MODE BRIGHT*, STANDARD,

SOFT

1 Choose AUTO PROGRAM, then press

the OK button.

The AUTO PROGRAM function starts.

The TV channels you receive are

automatically stored in the programme

numbers list.

DIGITAL VNR

AUTO (LOW), AUTO

(HIGH), MIN*, MAX

WHITE

BALANCE

COOL, MID*, WARM

>> AUTO PROGRAM

Super DigiPure AUTO, MAX*, OFF, MIN

CH 28

PICTURE

EFFECT

ON*:

14%

Above picture effect

applies to the chosen

video input.

OFF:

D0004-EN

No picture effect applies.

• To stop the AUTO PROGRAM

function, press the OK button.

*: When shipped

• For details of each item, see

“PICTURE MODE” on page 20,

“DIGITAL VNR” on page 21, “WHITE

BALANCE” on page 21, “Super

DigiPure” on page 22.

2 After the TV channels have been

stored in the programme number list,

the EDIT menu appears.

> EDIT

• When the signal is 625p or 525p:

- In “DIGITAL VNR”, AUTO

(LOW and HIGH) cannot be selected.

- In “Super DigiPure”, AUTO cannot be

selected.

CH/CC

• Pressing the blue button will return the

picture effect to the factory set value.

MANUAL

MOVE

INSERT DELETE

D0038-EN

5 Press the OK button to complete the

setting.

Using the TV’s menu

• You can proceed to edit the

programme numbers list using the

EDIT/MANUAL function. For details,

see “EDIT/MANUAL” on page 30

• If a TV channel you want to view is not

stored in the programme numbers list,

you can register it using the MANUAL

function.

1 Choose EDIT/MANUAL, then press the

OK or 3 button.

> EDIT

CH/CC

For details, see “EDIT/MANUAL” on

page 30.

MANUAL

MOVE

INSERT DELETE

• The AUTO PROGRAM function does

not store a TV channel to the

programme number 0 (AV).

• If you do not need to use the EDIT/

MANUAL function, press the OK

button to exit the EDIT menu.

• Starting the AUTO PROGRAM deletes

the registered favorite channel.

D0038-EN

2 Follow the operation description of a

function you want to use and operate

the function.

MOVE:

This function changes a programme

number of a TV channel.

ID:

This function registers a Channel name

(ID) to a TV channel.

„ EDIT/MANUAL

The EDIT/MANUAL functions are divided

into two types: editing of the current

programme numbers (EDIT functions) and

manual registration of a TV channel you

want to view to the programme number

(MANUAL function).

INSERT:

This function adds a new TV channel in

the current programme numbers list by

using the CH/CC number.

DELETE:

This function deletes an unnecessary TV

Channel.

CAUTION

• Using the MOVE, DELETE or INSERT

function rewrites the current programme

numbers list.

Resultingly, the programme number of

some of the TV channels will change.

• When a TV channel which has been

locked out using the CHANNEL GUARD

function, using the MANUAL function for

that TV channel cancels the CHANNEL

GUARD function.

MANUAL:

This function manually registers a new

TV channel in a programme number.

3 Press the OK button to complete the

setting.

• For programme number PR 0, “AV”

appears in the programme numbers

list.

• When a TV channel has already been

registered in PR 99, using the INSERT

function deletes the TV channel.

Using the TV’s menu

To cancel the ID function:

FUNCTIONS

MOVE

Press the BACK button.

4 Press the OK button to register a

channel name to a TV channel.

1 Press the 6 buttons to choose a TV

channel.

DELETE

2 Press the 3 button to start the MOVE

1 Press the 6 buttons to choose a TV

function.

channel.

> EDIT

2 Press the yellow button to delete the

TV channel.

CH/CC

CH 21

The TV channel is deleted from the

programme numbers list.

MANUAL

1 Press the 6 buttons to choose a

programme number to which you

want to register a new TV channel.

STORE

D0030-EN

2 Press the blue button to activate the

MANUAL function.

3 Press the 6 buttons to choose a

new programme number.

At the right side following the CH/CC

number, the SYSTEM (sound system) of

the TV channel appears.

To cancel the MOVE function:

Press the BACK button.

4 Press the 2 button to change the

programme number of a TV channel

to a new programme number.

> MANUAL

CH/CC

01 (

BBC1

1 Press the 6 buttons to choose a TV

channel.

)

B / G

2 Press the red button to start the ID

function.

SEARCH+

FINE-

SYSTEM

FINE+

SEARCH-

3 Enter a channel name (ID). Press the

6 buttons to choose a character.

Press the 5 buttons to move the

cursor.

D0035-EN

To cancel the MANUAL function:

Press the BACK button.

> EDIT

CH/CC

D0032-EN

Using the TV’s menu

3 Press the 3 button to choose the

system (sound system) for a TV

channel you want to register.

6 Press the OK button and register the

TV channel to a programme number.

The normal EDIT menu is resumed.

• For the sound systems in each country

or region, refer to the table below:

INSERT

Preparation:

• Find the CH/CC number

corresponding to the channel number

of the TV channel from page 35.

Area

Country or Region

System

B/G

Bahrain, Kuwait, Oman,

Qatar, United Arab Emirates,

Yemen, etc.

Indonesia, Malaysia,

Singapore, Thailand, India,

etc.

1 Press the 6 buttons to choose a

programme number for which you will

Asia,

Middle

East

China, Vietnam, etc.

Hong Kong, etc.

Islamic Republic of Iran,

Lebanon, Saudi Arabia, etc.

Philippines, Taiwan,

Myanmar, etc.

Russia, etc.

Czech Republic, Poland, etc. D/K

Germany, Holland, Belgium,

D/K

2 Press the green button to start the

INSERT function.

B/G

> EDIT

CH/CC

D/K

Europe

B/G

etc.

UK, etc.

Oceania Australia, New Zealand, etc. B/G

CH/CC

D0034-EN

Republic of South Africa, etc.

Nigeria, etc.

Egypt, Morocco, etc.

3 Press the 6 buttons to choose “CC”

or “CH” according to the CH/CC

number of the TV channel.

Africa

B/G

4 Press the green or red button to

search for a TV channel.

To cancel the INSERT function:

Press the BACK button.

Scanning stops when the TV finds a TV

channel. Then the TV channel is

displayed.

4 Press the Number buttons to enter the

remaining CH/CC number.

The TV shifts to registration mode. When

the registration is completed, the picture

of the TV channel appears on the

screen.

5 Press the green or red button

repeatedly until the TV channel you

want appears.

If the TV channel reception is poor:

Press the blue or yellow button to fine-

tune the TV channel.

If you cannot hear the normal sound

even when the picture of the TV

channel appears normally:

The SYSTEM setting is wrong. Press the

3 button and choose a SYSTEM that has

normal sound.

Using the TV’s menu

• The CH/CC number is a number

indicating the broadcast frequency to

the TV. If the TV cannot detect the TV

channel corresponding to the

broadcast frequency indicated by the

CH/CC number, a picture in the no-

signal state appears.

„ VIDEO-2 SETTING/VIDEO-3

SETTING

Set the VIDEO-2 SETTING or VIDEO-3

SETTING correctly according to the video

signal input from the external device

connected to the VIDEO-2 or VIDEO-3

terminal. If this setting is incorrect, images

will not be displayed.

„ LANGUAGE

VIDEO:

You can choose the language you want to

use for the on-screen display from the

language list in a menu.

If a normal video signal (composite video

signal) is input.

1 Choose LANGUAGE, then press the

OK button.

COMPONENT:

If a Component video signal (Y, Cb/Pb,

Cr/Pr signals) is input.

• For detailed connecting methods, see

“Additional preparation” on page 36.

This Television is compatible with the

1125i, 625p or 525p video signal only

when the component video signal is

input.

• When the input signal is 1125i, 625p or

525p, each signal type is displayed at

the upper right side on the TV screen

by setting the input to VIDEO-2 or

VIDEO-3.

2 Press the 6 buttons to choose a

language.

3 Press the OK button to complete the

setting.

The menu disappears.

„ AI VOLUME

„ PICTURE TILT

You can prevent the sudden increase or

decrease of sound that occurs when

changing the channel to another channel or

switching the VIDEO mode to another

VIDEO mode.

There are cases where the Earth’s

magnetic force may make the picture tilt. If

this happens, you can correct the picture tilt.

1 Choose PICTURE TILT, then press the

OK or 3 button.

ON:

> PICTURE TILT

This function is turned on.

OFF:

This function is turned off.

• The AI VOLUME function may not

operate as expected if the sound input

level from a broadcast station (or video

software) is extremely low.

• When the Video or the DVD is used, it

is recommended to select OFF to get

more dynamic sound.

D0018-EN

2 Press the 6 buttons until the

picture becomes level. Then press the

OK button.

Using the TV’s menu

3 Press the OK button to complete the

setting.

„ TELETEXT LANGUAGE

There are four types of teletext language

groups. Set the teletext language group that

corresponds to the language of the teletext

program that you want to watch.

The menu disappears.

• Languages that are not included in the

teletext language group that you

select, the sub-titles of the teletext

program will not be displayed properly.

1 Choose TELETEXT LANGUAGE, then

press the OK or 3 button.

> TELETEXT LANGUAGE

GROUP-1

GROUP-2

GROUP-3

GROUP-4

OSD-10-EN

2 Press the 6 buttons to choose a

group.

Group

Languages

GROUP-1 Turkish, Hungarian, English,

German, French, Italian,

Spanish, Portuguese, Greek,

Swedish, Finnish

GROUP-2 Polish, Serbian, Croatian,

Slovenian, Czech, Slovak,

Rumanian, Hungarian,

German, French, Italian,

Swedish, Finnish

GROUP-3 Russian, Bulgarian, Lettish,

Lithuanian, Estonian,

Ukrainian, Serbian, Croatian,

Slovenian, Czech, Slovak,

English, German

GROUP-4 Arabic, Czech, Slovak.

Hungarian, English, German,

French, Italian, Spanish,

Portuguese, Swedish, Finnish

Using the TV’s menu

CH/CC number

When you want to use the INSERT function on page 32, find the CH/CC number

corresponding to the Channel number of the TV channel from this table.

US: The US channel numbers are the channel numbers used in the United States,

Philippines, etc. CCIR: The CCIR channel numbers are the channel numbers used in the

Middle East, Southeast Asia, etc. OIRT: The OIRT channel numbers are the channel

numbers used in Eastern Europe, Russia, Vietnam, etc. AUSTRALIA: The AUSTRALIA

channel numbers are the channel numbers used in Australia, etc.

Channel

US-2

US-3

US-4

US-5

US-6

US-7

US-8

US-9

US-10

US-11

US-12

US-13

CCIR

OIRT

AUSTRALIA

AU-0

AU-1

AU-2

AU-6

AU-7

AU-8

AU-9

CCIR

S-1

S-2

S-3

S-4

S-5

S-6

S-7

S-8

OIRT

AUSTRALIA

AU-5

CH 02

CH 03

CH 04

CH 05

CH 06

CH 07

CH 08

CH 09

CH 10

CH 11

CH 12

CH 13

CH 14

CH 15

CH 16

CH 17

CH 18

CH 19

CH 20

CH 21

CH 22

CH 23

CH 24

CH 25

CH 26

CH 27

CH 28

CH 29

CH 30

CH 31

CH 32

CH 33

CH 34

CH 35

CH 36

CH 37

CH 38

CH 39

CH 40

CH 41

CH 42

CH 43

CH 44

CH 45

CH 46

CH 47

CH 48

CH 49

CH 50

CH 51

CH 52

CH 53

CH 54

CH 55

CH 56

CH 57

CH 58

CH 59

CH 60

CH 61

CH 62

CH 63

CH 64

CH 65

CH 66

CH 67

CH 68

CH 69

CC 01

CC 02

CC 03

CC 04

CC 05

CC 06

CC 07

CC 08

CC 09

CC 10

CC 11

CC 12

CC 13

CC 14

CC 15

CC 16

CC 17

CC 18

CC 19

CC 20

CC 21

CC 22

CC 23

CC 24

CC 25

CC 26

CC 27

CC 28

CC 29

CC 30

CC 31

CC 32

CC 33

CC 34

CC 35

CC 36

CC 37

CC 38

CC 39

CC 40

CC 41

CC 42

CC 43

CC 44

CC 45

CC 46

CC 47

CC 48

CC 49

CC 50

CC 51

CC 52

CC 53

CC 54

CC 55

CC 56

CC 57

CC 58

CC 59

CC 60

CC 61

CC 62

CC 63

CC 64

CC 75

CC 76

CC 77

CC 78

CC 79

CC 95

CC 96

CC 97

CC 98

CC 99

AU-5A

E10

E11

E12

R10

R11

R12

AU-10

AU-11

S-9

S-10

S-11

S-12

S-13

S-14

S-15

S-16

S-17

S-18

S-19

S-20

S-21

S-22

S-23

S-24

S-25

S-26

S-27

S-28

S-29

S-30

S-31

S-32

S-33

S-34

S-35

S-36

S-37

S-38

S-39

S-40

S-41

US-14, W+29

US-15, W+30

US-16, W+31

US-17, W+32

US-18, W+33

US-19, W+34

US-20, W+35

US-21, W+36

US-22, W+37

US-23, W+38

US-24, W+39

US-25, W+40

US-26, W+41

US-27, W+42

US-28, W+43

US-29, W+44

US-30, W+45

US-31, W+46

US-32, W+47

US-33, W+48

US-34, W+49

US-35, W+50

US-36, W+51

US-37, W+52

US-38, W+53

US-39, W+54

US-40, W+55

US-41, W+56

US-42, W+57

US-43, W+58

US-44, W+59

US-45, W+60

US-46, W+61

US-47, W+62

US-48, W+63

US-49, W+64

US-50, W+65

US-51, W+66

US-52, W+67

US-53, W+68

US-54, W+69

US-55, W+70

US-56, W+71

US-57, W+72

US-58, W+73

US-59, W+74

US-60, W+75

US-61, W+76

US-62, W+77

US-63, W+78

US-64, W+79

US-65, W+80

US-66, W+81

US-67, W+82

US-68, W+83

US-69, W+84

E21

E22

E23

E24

E25

E26

E27

E28

E29

E30

E31

E32

E33

E34

E35

E36

E37

E38

E39

E40

E41

E42

E43

E44

E45

E46

E47

E48

E49

E50

E51

E52

E53

E54

E55

E56

E57

E58

E59

E60

E61

E62

E63

E64

E65

E66

E67

E68

E69

W+1

W+2

W+3

W+4

W+5

W+6

W+7

W+8

W+9

W+10

W+11

W+12

W+13

W+14

W+15

W+16

W+17

W+18

W+19

W+20

W+21

W+22

W+23

W+24

W+25

W+26

W+27

W+28

Z+1

Z+2

AU-3

AU-4

A-5

A-4

A-3

A-2

A-1

Additional preparation

„ Connecting the external

devices

Connect the devices to the TV, paying

attention to the following connection

diagram.

HV-Z34L1

HV-Z29V1

Before connecting anything:

• Read the manuals provided with the

devices. Depending on the devices,

the connection method may differ from

the figure. In addition, the device

settings may be changed depending

on the connection method to secure

proper operation.

(Behind the cover)

• Turn off all the devices including the

TV.

• The “Specifications” on page 43

contains the details of the VIDEO

terminals. If you are connecting a

device not listed in the following

connection diagram, see the

“Specifications” to choose the best

VIDEO terminal.

OVER

L/MONO

IN (VIDEO-4)

• Note that connecting cables are not

supplied.

1 VCR (composite signal)

2 VCR (S-VIDEO signal; Y/C)

3 VCR for recording (composite signal)

4 DVD player (composite signal)

5 DVD player (S-VIDEO signal; Y/C)

6 DVD player (component video signals;

Y, Cb/Pb, Cr/Pr)

Back of the TV

7 TV game (composite signal)

8 TV game (S-VIDEO signal; Y/C)

9 Camcorder (composite signal)

0 Camcorder (S-VIDEO signal; Y/C)

- Headphones

Additional preparation

If connecting a device to the VIDEO-2

(COMPONENT) or VIDEO-3 (COMPONENT)

terminal with a video cable.

Connect the TV’s VIDEO jack and the

device’s VIDEO OUT (video output) jack

with a video cable.

Then set the VIDEO-2 SETTING or VIDEO-

3 SETTING to VIDEO according to “VIDEO-

2 SETTING/VIDEO-3 SETTING” on

page 33.

Connecting methods

1 Connect the TV’s VIDEO jack and the

device’s VIDEO OUT (video output)

jack with a video cable.

If connecting a device to the TV with an

S-VIDEO cable:

Connect the VCR’s S-VIDEO OUT (S-

VIDEO output) connector and the TV’s S

connector with an S-VIDEO cable, instead

of connecting with a video cable.

Note that the connection with a video cable

will be ignored in case you connect a VCR

to the TV with both video cable and S-

VIDEO cable.

• In the VIDEO-4 terminal, the VIDEO

jack is indicated by “V”.

2 Connect the TV’s AUDIO jacks (L/

MONO and R) and the device’s AUDIO

OUT (audio L/R output) jacks with an

audio cable.

If connecting a DVD player to the TV with

a component video cable.

If the device’s sound output is in mono:

Connect the device’s AUDIO OUT jack and

the TV’s L/MONO jack with an audio cable.

Connect three jacks (Y, Cb/Pb, Cr/Pr) in the

VIDEO-2 or VIDEO-3 terminal and the DVD

player’s COMPONENT (component video

output) jacks with a component video

cables, instead of connection with a video

cable. Then set the VIDEO-2 SETTING/

VIDEO-3 SETTING to COMPONENT,

according to “VIDEO-2 SETTING/VIDEO-3

SETTING” on page 33.

Connecting devices to the

OUTPUT terminal

The signals of the images and sound you

are currently viewing with this TV are output

through the OUTPUT terminal. By

connecting a VCR to the OUTPUT terminal,

you can record the currently shown image

and sound to that VCR. To do this, connect

the VCR and OUTPUT terminal following

the steps below.

• If you have a DVD player that outputs

1125i, 625p or 525p video signals as a

component video signal, then by

attaching the device to the television

with a component video cable you can

see the actual images that are

1 Connect the VIDEO jack in the

OUTPUT terminal and the VCR’s

VIDEO IN (video input) jack with a

video cable.

recorded on a DVD disc as an original

image source.

2 Connect the AUDIO jacks (L and R) in

the OUTPUT terminal and the VCR’s

AUDIO IN (audio L/R input) jacks with

an audio cable.

• When you turn off the TV, the signals

from the OUTPUT terminal are also

turned off.

• The component signals input from the

VIDEO-2 (COMPONENT) or VIDEO-3

(COMPONENT) terminal cannot be

output through the OUTPUT terminal.

Additional preparation

Connecting Headphones

Connect the headphones with a stereo

mini jack (of 3.5 mm in diameter) to the

Headphone jack at the TV front panel.

Conditions to use the AV COMPU

LINK remote control system

• A device equipped with an AV COMPU

LINK terminal is required.

• You must connect the TV and the

device with an AV COMPU LINK cable.

AV COMPU LINK cable is not supplied

with this TV. If an AV COMPU LINK

cable is unavailable, connect them with

a cable with dia. 3.5 mm (mono) male

plugs at both ends.

• You must connect the device to an

appropriate VIDEO terminal and set it

up correctly. Otherwise the AV

COMPU LINK remote control system

will not function correctly. For details,

see “Setting up the AV COMPU LINK

remote control system”.

• The TV must be in standby mode (the

POWER lamp lighting red). If the TV’s

Main power is off (the POWER lamp

off), the AV COMPU LINK remote

control system does not function.

„ Connecting AV COMPU LINK

Supported Devices

AV COMPU LINK remote control system is

a system in which related devices are

automatically controlled when you operate

one device.

If you apply this system to the TV, you can

have the TV automatically perform the

required operations by operating one

external device. You don’t have to use the

TV’s remote control to turn on the TV or

change the VIDEO modes.

Examples of the AV COMPU LINK

remote control system

operations

Simply by pressing the PLAY button on a

VCR or a DVD player, you can view images

from the device.

Simply by inserting a prerecorded tape (a

tape with the record safety tab removed) to

a VCR, you can view the tape.

Simply by operating the AV Control

Receiver, you can have the TV turned on/off

(in standby mode) or the VIDEO mode

changed correctly.

Setting up the AV COMPU LINK

remote control system

CAUTION:

• With some devices, the setup method

differs from the ones explained here. Be

sure to read the device’s instruction

manual thoroughly before setting it up.

• The performance of the AV COMPU

LINK remote control system varies

depending on the connected device.

See the device’s instruction manual.

• When you select “TV SOUND” as the

input source with the AV Control

Receiver, there are cases where the

TV’s MUTING function automatically

operates and the sound from the TV’s

speakers is muted.

In such cases, press the VOLUME-/+

buttons or the MUTING button on the

TV’s remote control to cancel the

MUTING function. You can regain the

sound from the TV’s speakers.

1 Connect the device to the TV’s VIDEO-1,

VIDEO-2 (COMPONENT) or VIDEO-3

(COMPONENT) terminal.

If you want to connect a DVD player to

the TV with a component video cable:

Connect the DVD player to the TV’s

VIDEO-2 (COMPONENT) or VIDEO-3

(COMPONENT) terminal.

• For detailed connecting instructions,

see “Connecting the external devices”

on page 36.

2 Connect the TV’s AV COMPU LINK

terminal and the device’s AV COMPU

LINK terminal with an AV COMPU

LINK cable.

Additional preparation

3 Change the device’s setting

according to the VIDEO terminal it is

connected to.

If a VCR is connected to the VIDEO-1

terminal:

Set the VCR’s remote control code to A

code.

If a DVD player is connected to the

VIDEO-1 terminal:

Set the DVD player’s AV COMPULINK

MODE to DVD2.

If a VCR is connected to the VIDEO-2

(COMPONENT) terminal:

Set the VCR’s remote control code to B

code.

If a DVD player is connected to the

VIDEO-2 (COMPONENT) terminal:

Set the DVD player’s AV COMPULINK

MODE to DVD3.

If a DVD player is connected to the

VIDEO-3 (COMPONENT) terminal with a

component video cable:

Set the DVD player’s AV COMPULINK

MODE to DVD1.

• For instructions on how to change the

device’s setting, refer to the device’s

instruction manual.

• If the device you are connecting has

neither the remote control code nor the

AV COMPULINK MODE, then connect

it to the TV’s VIDEO-1 terminal.

Troubleshooting

If a problem arises while you are using the TV, please read this “Troubleshooting” well

before you request having the TV repaired. You may be able to fix it easily by yourself. For

example, if the AC plug is disconnected from the AC outlet, or the TV aerial has problems,

you may think there is a problem with the TV itself.

Important:

• This Troubleshooting guide only covers problems whose causes are not easy to

determine. If a question arise when you are operating a function, read the page(s)

corresponding to the operation of the function well, not this Troubleshooting guide.

• After you have followed the Troubleshooting description or the operating description of

the functions concerned without any success, remove the AC plug from the AC outlet

and request a repair of your TV. Do not attempt to repair the TV by yourself or remove

the rear cover of the TV.

„ If you cannot turn on the TV

• Is the AC plug connected to the AC

outlet?

„ Poor picture

• If noise totally obscures the picture

(snow), the aerial or aerial cable may

have trouble. Check the following to try

to solve the trouble:

• Is the POWER lamp lit? If not, press

the Main power button.

• Make sure to set the PIP/TV/DVD

switch to the TV or PIP position. You

cannot turn the TV on when the PIP/

TV/DVD switch is set to the DVD

position.

Has the TV and aerial been connected

properly?

Has the aerial cable been damaged?

Is the aerial pointed to the right

direction?

Is the aerial itself faulty?

„ If you cannot turn off the TV

• Make sure to set the PIP/TV/DVD

switch to the TV or PIP position. You

cannot turn the TV off when the PIP/

TV/DVD switch is set to the DVD

position.

• If the TV or aerial receives interference

from the other devices, stripes or noise

may appear in the picture. Move such

device as an amplifier, personal

computer, or a hair drier that can

cause interference away from your TV,

or try changing its location. If the aerial

suffers interference from a radio tower

or high-voltage wire, please contact

your local dealer.

• If the TV receives interferences from

signal reflecting from mountains or

building, double-pictures (ghosting) will

occur.

Try to change the aerial’s direction or

replace the antenna with the one with

better directionality.

„ No picture/No sound

• Have you chosen a TV channel whose

reception is extremely bad? In this

case, the BLUE BACK function will be

activated, the entire screen becomes

blue, and the sound is muted. In spite

of this, if you want to view the TV

channel, follow the description “BLUE

BACK” on page 27 to try to change the

BLUE BACK function setting to OFF.

• Are your SOUND SYSTEM settings for

the TV channels correct?

• Are your COLOUR SYSTEM settings

for the TV channels correct? Follow

the description “COLOUR SYSTEM”

on page 23 to try to solve the trouble.

Follow the description “EDIT/

MANUAL” on page 30 to use the

MANUAL function to try to change the

SYSTEM setting.

Troubleshooting

• Has COLOUR or BRIGHT been

controlled properly? Follow the

description “Adjusting the picture” on

page 20 to try to adjust them properly.

• Videotaping teletext is not

recommended because it may not

record correctly.

• When a white and bright still image

(such as a white dress) is displayed on

the screen, the white part may look as

if it were coloured.

It is a phenomenon unavoidable due to

the nature of the picture tube itself, and

not due to a TV failure.

When the picture disappears from the

screen, the unnatural colours will also

disappear.

• When viewing images from

commercially available video software

products, or videos from videotapes

which have been recorded improperly,

the top of the image may be distorted.

This is due to the condition of the video

signal, and not because of

„ Operation disabled

• Have the batteries of the remote

control become exhausted?

Follow the description “Putting the

batteries into the remote control” on

page 4 and replace them with new

batteries to try solve the problem.

• Have you attempted to use the remote

control at the sides or rear of the TV or

at a location more than seven meters

apart from the TV location? Operate

the remote control in the front of your

TV or a location less than seven

meters from your TV to try to solve the

problem.

• When you are viewing a teletext

programme, you cannot operate the

menus.

Press the BACK or TV/VIDEO button

to return the teletext programme to the

ordinary TV programme to try

operating the menus.

• Is the CHILD LOCK function set to

ON? If the CHILD LOCK function is set

to ON, you cannot operate the TV with

the front control buttons of the TV.

Follow the description “CHILD LOCK”

on page 27 to try to set the CHILD

LOCK function to OFF.

• If the TV operation becomes disabled

suddenly, press the Main power button

on the TV and turn off the main power.

Try to press the Main power button

again to turn on the main power. If the

TV returns to a normal state, it is not a

failure.

malfunction.

„ Poor sound

• When the TV channel reception is

poor, it can be hard to hear the stereo

or bilingual sound. In this case, follow

the description “STEREO / I•II” on

page 24 to hear the sound more easily

by changing it to a mono sound.

• The following functions do not operate

when receiving 1125i, video signal.

- Twin, PIP, Multi-display, FREEZE

and STROBE functions

Troubleshooting

• Touching the screen may cause you

feel a slight electric shock due to its

static electricity.

It is an unavoidable phenomenon due

to the construction of the picture tube.

It is not a problem with the TV.

You can rest assured that this static

discharge does not have harmful

influence over the human body.

„ Other concerns

• When the AUTO SHUTOFF function

operates, the TV is automatically

turned off.

If the TV is turned off suddenly, try to

press the # button to turn on the TV

once again. At this time, if the TV

resumes a normal state, there is no

problem.

• If you bring a magnetized device such

as a speaker near to your TV, a picture

may be warped or unnatural colours

appear at the corners of the screen. In

this case, keep the device apart from

your TV. If the speaker causes such

phenomena, use the magnetic-

shielded speaker instead.

• A picture may be tilted due to the

influence of the earth’s magnetism. In

this case, use the “PICTURE TILT” on

page 33 to complete the tilt.

• It takes a short period of time from the

time an operation such as changing

channels is performed until an image is

displayed. This is not a malfunction.

This is the time required for the image

to stabilize before it can be displayed.

• The TV may emit a crackling sound

due to a sudden change in

temperature. It does not matter if a

picture or sound does not show any

abnormality. If you hear crackling

sounds frequently while you are

viewing the TV, other causes may be

assumed.

For precautionary purposes, request

your service technician to inspect it.

Specifications

Broadcasting systems

Colour systems

B, G, I, D, K, K1, M

PAL, SECAM, NTSC3.58/4.43MHz

Channels and frequencies

VHF low channel (VL) =46.25 to 168.25 MHz

VHF high channel (VH) =175.25 to 463.25 MHz

UHF channel (U)

=471.25 to 863.25 MHz

• Receives cable channels in mid band (X to Z+2, S1 to S10), super band (S11

to S20) and hyper band (S21 to S41).

Sound-multiplex systems

Teletext systems

A2 (B/G), NICAM (B/G, I, D/K) system

FLOF(Fastext), WST(World Standard Text)

Languages displayed by

teletext

Please see the table in the description “TELETEXT LANGUAGE” on page 34.

Power requirements

Audio output

AC 110 to 240V, 50/60Hz

Rated Power output: 15W + 15W [HV-Z34L1], 10W + 10W + 18W [HV-Z29V1]

VIDEO-1 terminal

RCA connector × 3, S-VIDEO connector × 1

• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.

VIDEO-2 (COMPONENT)

VIDEO-3 (COMPONENT)

RCA connector × 6

• Video input, Componet video (Y, Cb/Pb, Cr/Pr) input and Audio L/R inputs are

available.

• 625p, 525p and 1125i signals are available.

RCA connector × 6

• Video input, Componet video (Y, Cb/Pb, Cr/Pr) input and Audio L/R inputs are

available.

• 625p, 525p and 1125i signals are available.

VIDEO-4 terminal

OUTPUT terminal

RCA connector × 3, S-VIDEO connector × 1

• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.

RCA connector × 3

• Video output and Audio L/R outputs are available.

Headphone jack

Accessories

Stereo mini-jack (3.5 mm in diameter)

Remote control unit × 1 (RM-C1850)

AA/R6 dry cell battery × 2

Woofer unit × 1 [HV-Z29V1 only]

Speakers

HV-Z34L1: 12cm round × 2, 3.5cm round × 2

HV-Z29V1: (13cm × 6.5cm) oval × 2, 13cm round × 1(Woofer unit)

Design and specifications subject to change without notice.

Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any commercial or

demonstration purpose in public places (cafes, hotels, etc.) without the consent of the owners of copyright of

the original picture sources, as this constitutes an infringement of copyright.

This TV does not conform to the PAL-D Chinese broadcasting system.

VICTOR COMPANY OF JAPAN, LIMITED

COLOUR TELEVISION

Contents

Setting up your TV. . . . . . . . . . . . . . . . . . 3

TV buttons and functions. . . . . . . . . . . . . 6

Remote control buttons and functions. . . 8

Using the TV’s menu. . . . . . . . . . . . . . . 19

PICTURE menu . . . . . . . . . . . . . . . . . 20

FEATURES menu . . . . . . . . . . . . . . 21

SOUND menu. . . . . . . . . . . . . . . . . . . 24

FEATURES menu. . . . . . . . . . . . . . . . 26

SETUP menu . . . . . . . . . . . . . . . . . . . 29

Additional preparation . . . . . . . . . . . . . . 36

Troubleshooting. . . . . . . . . . . . . . . . . . . 40

Specifications . . . . . . . . . . . . . . . . . . . . 43

HV-Z34L1

HV-Z29V1

INSTRUCTIONS

LCT1460-001A-H

1103-CR-JMT

Thank you for buying this JVC colour television.

To make sure you understand how to use your new TV, please read this manual thoroughly

before you begin.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

CAUTION: TO ENSURE PERSONAL SAFETY, OBSERVE THE FOLLOWING

RULES REGARDING THE USE OF THIS TV.

1 Operate only from the power source indicated on the rear of the TV.

2 Avoid damaging the power cord and mains plug. When unplugging the TV, grasp the

mains plug. Do not pull on the power cord.

3 Never block or cover the ventilation openings.

Never install the TV where good ventilation is unattainable.

When installing this TV, leave spaces for ventilation around the TV of more than the

minimum distances as shown.

15 cm

10 cm

15 cm

4 Do not allow objects or liquid into the cabinet openings.

5 In the event of a fault, unplug the unit and call a service technician. Do not attempt to repair

it yourself or remove the rear cover.

6 The surface of the TV screen is easily damaged. Be very careful with it when handling the

TV. Should the TV screen become soiled, wipe it with a soft dry cloth. Never use rub it

forcefully. Never use any cleaner or detergent on it.

7 If you are not going to use this TV for a long period of time, be sure to disconnect the AC

plug from the AC socket.

8 The apparatus shall not be exposed to dripping or splashing and that no objects filled with

liquids, such as vases, shall be placed on the apparatus.

D.I.S.T. demonstration

To start the D.I.S.T. demonstration:

Press the H button to display the menu bar. Then press the yellow button.

A picture split in two (D.I.S.T. turned on and D.I.S.T. turned off) will appear on the screen.

To quit the D.I.S.T. demonstration:

Press the yellow button, BACK button, CHANNELp buttons or any of the number buttons.

Setting up your TV

CAUTION

• Turn off all the equipment including the

TV before connecting anything.

1 Connecting the woofer unit

(only for HV-Z29V1)

1 Fitting the woofer unit

Align the projection on the base of the

woofer unit with the hole in the top of the

TV, and insert the connector into the

woofer terminal.

2 Connecting the supplied woofer

connector to the BASS SPEAKER

OUT terminal on the back of the TV

If the woofer unit is not connected, you

will not be able to enjoy the bass sound.

• Connect so that the lever is raised.

• When disconnecting the woofer

Lever

connector, do so while pushing the lever.

2 Connecting the aerial and VCR

• Aerial cable is not supplied. Use a

good quality 75-ohm coaxial cable.

• Read the manual that came with the

VCR before connecting.

Fig. A

If not connecting a VCR (see Fig. A):

Connect an aerial cable to the aerial socket

on this TV.

If connecting a VCR (see Fig. B):

Fig. B

1 Connect the aerial cable to the aerial

input socket on the VCR, and connect

the VCR and TV with another aerial

cable.

2 Connect the VCR’s VIDEO OUT (video

output) jack and the TV’s VIDEO jack

with a video cable.

To connect a VCR to the TV with an

S-VIDEO cable:

Connect the VCR’s S-VIDEO OUT (S-

VIDEO output) connector and TV’s S

connector with an S-VIDEO cable A,

instead of connecting with a video cable.

3 Connect the VCR’s AUDIO OUT (audio L/

R output) jacks and the TV’s AUDIO jacks

(L/MONO and R) with an audio cable.

• If the VCR’s audio output is in mono,

connect the VCR’s AUDIO OUT (audio

output) jack and the TV’s AUDIO L/

MONO jack with an audio cable.

Setting up your TV

3 Connecting the power cord

Connect the mains plug to the AC outlet.

4 Putting the batteries into the

remote control

Use two AA/R6 batteries.

Insert the batteries from the - end, making

sure the + and - polarities are correct.

• Follow the warnings printed on the

batteries.

HV-Z34L1

• If the remote control does not work

properly, replace the batteries.

• The batteries we supply are only for

setting up and testing your TV. Please

replace them as soon as necessary.

POWER

POWER lamp

Main power button

5 Making the initial settings

(SETUP TOUR)

When the TV is first turned on, it enters the

initial setting mode, and the JVC logo is

displayed.

HV-Z29V1

1 Press the main power button on the TV.

The TV is turned on, and the JVC logo

appears.

POWER

• If the POWER lamp on the TV lights

red and does not change to green,

your TV is in the standby mode. Press

the # button on the remote control to

turn the TV on.

POWER lamp

Main power button

• If the JVC logo does not appear, your

TV has already been turned before. In

this case, use the “LANGUAGE”,

“TELETEXT LANGUAGE” and “AUTO

PROGRAM” functions to make the

initial settings. For details, see

FAVORITE CHANNEL

SUB-P

TV/VIDEO

“SETUP menu” on page 29.

DISPLAY

BACK

2 Press the OK button on the remote

control.

SUB-P

CHANNEL

VOLUME

The LANGUAGE menu appears. You

can choose a language for the on-screen

language.

Setting up your TV

5 After the TV channels have been

3 Press the 6 buttons to choose

ENGLISH. Then press the OK button

on the remote contol.

stored in the programme numbers

(PR) list, the EDIT menu appears.

The TELETEXT LANGUAGE menu

appears. Set the teletext language group

that corresponds to the language of the

teletext program that you want to watch.

For details, see “TELETEXT

> EDIT

CH/CC

LANGUAGE” on page 34.

> TELETEXT LANGUAGE

MANUAL

GROUP-1

GROUP-2

GROUP-3

GROUP-4

MOVE

INSERT DELETE

D0038-EN

• You can proceed to edit the

programme numbers list using the

EDIT/MANUAL function. For details,

see “EDIT/MANUAL” on page 30.

• If a TV channel you want to view is not

stored in the programme numbers list,

you can register it using the MANUAL

function. For details, see “EDIT/

MANUAL” on page 30.

OSD-10-EN

4 Press the 6 buttons to choose a

group. Then press the OK button.

The AUTO PROGRAM function starts.

The TV channels you receive are

automatically stored in the PR

(programme numbers) LIST.

>> AUTO PROGRAM

• The AUTO PROGRAM function does

not store a TV channel to the

CH 28

14%

programme number 0 (AV).

• If you do not need to use the EDIT/

MANUAL function, press the OK

button to close the EDIT menu.

D0004-EN

• To stop the AUTO PROGRAM

function, press the OK button.

Now, setting up is complete. Please

enjoy your new JVC TV!

TV buttons and functions

Turn the main power on

Press the main power button 1.

The POWER lamp 2 lights red and your TV

is in the standby mode.

HV-Z34L1

To turn the main power off:

Press the main power button again. The

POWER lamp 2 goes off.

Turn the TV on from standby

mode

Press the CHANNEL-/+ buttons 5.

The POWER lamp 2 lights red to green

and your TV will be turned on.

POWER

• You can also turn on the TV by

pressing the TV/VIDEO button 3

while it is in standby mode.

Choose a TV channel

HV-Z29V1

Press the CHANNEL-/+ buttons 5.

Choose a VIDEO terminal

Press the TV/VIDEO button 3 or

CHANNEL-/+ buttons 5.

Adjust the volume

Press the VOLUME-/+ buttons 4.

The volume level indicator appears.

MENU button 6

Press to open the menu.

POWER

For details, see “Operation with the buttons

on the TV” on page 20.

Remote control sensor 7

HV-Z34L1

VIDEO-4 terminal 8

See page 36.

HV-Z29V1

Headphone jack 9

Connect the headphones with a stereo

mini-jack (3.5mm in diameter).

(Behind the cover)

OVER

L/MONO

CHANEL

VOLUME TV/VIDEO

EXIT

IN (VIDEO-4)

6 5 4 3

TV buttons and functions

VIDEO-1 terminal 0

Back of the TV

• See pages 3 and 36.

VIDEO-2 (COMPONENT)

terminal -

• See pages 33 and 36.

VIDEO-3 (COMPONENT)

terminal =

• See pages 33 and 36.

OUTPUT terminal ~

• See page 37.

Aerial socket !

Connect the aerial cable.

• See page 3.

AV COMPU LINK terminal @

• See page 38.

BASS SPEAKER OUT terminal

# (only for HV-Z29V1)

• See page 3.

Remote control buttons and functions

Turn the TV on from standby

mode

Press the # button.

The POWER lamp lights red to green and

your TV will be turned on.

• You can turn on the TV from the

standby mode by pressing the TV/

VIDEO button, the CHANNELp

buttons or the number buttons.

To turn the TV off:

Press the # button again.

The POWER lamp changes from green to

red and the TV enters standby mode.

RETURN+

To turn the TV on or off, set the PIP/TV/

DVD switch on the remote control to the

TV or PIP position and press the #

button.

FAVORITE CHANNEL

If the PIP/TV/DVD switch on the remote

control is set to the DVD position, the TV

will not be turned on or off even if the #

button is pressed.

SUB-P

TV/VIDEO

Choose a TV channel

Choose a programme number in which a

TV channel has been set.

DISPLAY

BACK

SUB-P

CHANNEL

VOLUME

Press the CHANNELp buttons or enter

the programme number (PR) with the

number buttons.

Example:

•

PR 6 → press 6

PR 12 → press 1 and 2

SOUND

CINEMA

MODE SURROUND BASS ZOOM

• You can select a channel from the PR

LIST. For details, see “DISPLAY

button” on page 11.

F.T/L

TOP MENU

• If you do not have a clear picture or no

colour appears, follow the operation

procedure “COLOUR SYSTEM” on

page 23.

STROBE

Remote control buttons and functions

ZOOM:

You can zoom up the Wide picture (16:9

aspect ratio) to fill the TV screen.

Adjust the volume

Press the VOLUME-/+ buttons.

Watch images from an

external device

Choose a VIDEO terminal to which the

external device has been connected.

• The left side and right side of the Wide

picture (16:9 aspect ratio) will be cut off.

16:9:

This mode converts a normal picture (4:3

aspect ratio) into a Wide picture (16:9

aspect ratio).

Press the TV/VIDEO button.

• You can choose a VIDEO terminal with

the CHANNELp buttons or from the

PR LIST.

To return to a TV channel:

Press the TV/VIDEO button, the

CHANNELp buttons or the number buttons.

l (Muting) button

Press the l (Muting) button to turn off the

volume. Pressing the l (Muting) button

again resumes the previous volume level.

• Use for picture with a 16:9 aspect ratio

that have been squeezed into a normal

picture (4:3 aspect ratio), you can

restore their original dimensions.

• When a 1125i signal is input, the 16:9

aspect ratio is chosen automatically.

ZOOM button

You can change the screen size according

to the picture aspect ratio. Choose the

optimum one from the following ZOOM

modes.

CINEMA SURROUND button

You can enjoy an enhanced sound for a

wider audience by using CINEMA

SURROUND function.

Press the CINEMA SURROUND button to

select one of CINEMA SURROUND modes.

1 Press the ZOOM button to display the

ZOOM menu.

• The ZOOM button works only in the

normal screen.

>> ZOOM

HIGH/LOW:

When you listen to the stereo sound, please

select HIGH or LOW mode.

REGULAR

ZOOM

16:9

You can enjoy the sound for a wider

audience similar to the experience at the

theatre.

D0017-EN

When you combine the functions of SOUND

MODE, SUPER BASS and DIGITAL BBE,

you can enjoy more powerful sound.

• In case that you setting up the

CINEMA SURROUND function to

HIGH mode, there may be slight

volume distortion. In case that occurs,

please switch the HIGH mode to LOW

mode, the effect of CINEMA

2 Press the 6 buttons to choose a

ZOOM mode. Then press the OK button.

REGULAR:

Use to view a normal picture (4:3 aspect

ratio) as its original size is.

SURROUND functions will be less

noticeable, however, the volume

distortion will be corrected.

Remote control buttons and functions

MONO:

RETURN+ button

Select the MONO mode, when you listen to

the mono sound.

You can enjoy the sound for a wider

The RETURN+ button has two functions;

the RETURN+ function and the RETURN

function. If a channel has been registered

as the “Return Channel”, the RETURN+

function operates. If there is no setting for

the “Return Channel”, the RETURN function

operates.

audience similar to stereo sound.

OFF:

The CINEMA SURROUND function

switches off.

SOUND MODE button

RETURN+ function

You can select the SOUND MODE of you

liking from 4 types of sound modes to fully

enjoy the sound of your TV.

By registering a channel you frequently

view as the “Return Channel”, you can

select that channel at any time simply by

pressing the RETURN+ button.

Press the SOUND MODE button to select

one of sound modes.

DYNAMIC:

Dynamic sound is created by enhancing

To register a TV channel as the “Return

Channel”:

high and low tones.

You can get the 3D effect by using the

CINEMA SURROUND function in this mode.

Choose the Programme number to which

the channel you want to register has been

set, and press the RETURN+ button and

hold for more than 3 seconds continuously.

“RETURN PLUS PROGRAMMED!” is

displayed and the registration is completed.

MUSIC:

The mode suitable for music programmes.

Enjoy a concert hall-like atmosphere.

Combination with the CINEMA SURROUND

function will bring wider range sound.

To cancel a TV channel registered as the

“Return Channel”:

NEWS:

While viewing any TV channel, press the

RETURN+ button and hold for more than 3

seconds continuously. “RETURN PLUS

CANCELED!” is displayed and the

registration is cancelled.

The mode suitable for news programmes

makes the voice of the newscaster or the

like easier to hear.

USER:

Save your own sound setting to memory

with this mode.

The USER setting is performed with the

“SOUND MODE” menu (see page 25).

• When you turn off the TV, the

registration for the “Return Channel” is

cancelled.

• If you want to view the “Return

Channel” and another TV channel

alternately, first choose a channel

other than the “Return Channel”. And

then press the RETURN+ button to

change the channel to the “Return

Channel” In this way, you can view two

channels alternately by pressing the

RETURN+ button.

BASS button

You can choose the SUPER BASS mode

which emphasizes the bass sound.

Press tge BASS button to select one of

SUPER BASS modes.

You can choose HIGH, MID or LOW.

Choosing LOW will reduce the bass sound

and choosing HIGH will increase the bass

sound.

Remote control buttons and functions

RETURN function

Choose a TV channel or a

VIDEO terminal

1 Press the DISPLAY button to display

the PR LIST.

The TV temporarily memorises the TV

channel that was chosen right before the

current TV channel as the “Last Channel”.

By pressing the RETURN+ button, you can

alternately view the current TV channel and

the “Last Channel”.

2 Press the 6 and 5 buttons to

choose a programme number or

VIDEO terminal.

• If you want to view two channels

alternately by using the RETURN

function, first choose one TV channel

and then choose the other TV channel

with the Number buttons. If you choose

the TV channel without using the

Number buttons, there are cases

where a channel other than the one

you first chose is registered as the

“Last Channel”.

Then press the OK button.

• For programme numbers with the

CHANNEL GUARD function set, the n

(CHANNEL GUARD) mark is

displayed next to the programme

number in the PR LIST.

• The VIDEO terminals are registered

after the programme number PR99.

• The AV channel (channel number 0) in

the PR LIST will be chosen only if you

connect the VCR to the TV with an

aerial cable without connecting a video

cable.

DISPLAY button

You can display the PR LIST, programme

number or VIDEO terminal number on the

screen.

Favorite channel registration

You can register your favorite TV channels

with the colour buttons (Red, Green, Yellow

and Blue). After registration you can recall

the favorite channel by pressing the colour

button.

Press the DISPLAY button.

Press the DISPLAY button changes the

display as follows:

PR LIST

1 In the normal screen, choose a TV

channel (PR01-99) you want to

Programme or VIDEO

terminal number

For detailed operation, see “Choose a

TV channel” on page 8.

No indication

2 Press and hold a colour button for 3

seconds or more.

-10

+10

Then “FAVORITE CH PROGRAMMED”

appears on the screen and the current

channel is registered.

D0011-EN

Remote control buttons and functions

• If the chosen channel is already

registered as the favorite channel,

when a colour button is pressed, the

registered colour button icon appears

on the top right of the screen.

• You cannot register in the Text mode,

or while multiple screens, such as PIP

(picture in picture) are displayed.

• Also you cannot register if the chosen

channel is guarded with the CHANNEL

GUARD function and the screen is

blue, or if an on-screen menu is

displayed.

„ Showing the favorite channels

Press the DISPLAY button to display the

PR LIST.

You can see the favorite channel that has

the registered colour button icon at the right

of the channel number.

PR LIST

• Starting the AUTO PROGRAM deletes

the registered favorite channel.

-10

+10

D0011-EN

„ Recalling the favorite channel

Press the colour button, then the registered

favorite channel will be displayed.

Twin and PIP (picture in

picture) function

You can view two pictures (Main picture and

sub picture). Two different TV programmes

can be watched at the same time or a TV

programme and a video programme from

an externaldevice can be watched at the

same time.

• You cannot recall the favorite channel

in the Text mode, Menu mode where

an on-screen menu is displayed.

• The picture effect dedicated for the

colour button applies. For details, see

“Setting the picture effect” below:

„ Setting the picture effect

Each colour button has a dedicated picture

effect. When you choose a favorite channel

with a colour button, the dedicated picture

effect is used. When shipped, the factory

set picture effect is used for this purpose.

However, you can set this picture effect as

required. For details, see “FAVORITE

SETTING” on page 28.

Operate with the PIP/TV/DVD switch set

to the PIP position.

Twin mode

Press

Each time it is pressed the mode changes

as shown below.

Normal screen

Twin mode

Sub

Main

Remote control buttons and functions

PIP (picture in picture) mode

Press

Each time it is pressed the mode changes

as shown below.

„ Listening to the sound of the

sub-picture:

You can listen to the sound of the sub-

picture with the headphones while listening

to the sound of the main-picture from the TV

speakers.

Normal screen

PIP mode

For details, see “HEADPHONE VOLUME”

on page 25.

Sub

• The sub-picture sound is monaural.

Main

To return to the normal screen:

„ TV channel selection

For the main picture:

Choose a channel using the CHANNELp

buttons or the number buttons.

Press the

again, or press the

BACK button.

For the sub picture:

Choose a channel using the SUB-P6

buttons.

• The

and

buttons do not work in

the Text mode.

• Twin and PIP functions do not work for

a picture of 1125i signal.

„ Input source selection (TV,

• A picture of 625p or 525p signal

cannot be displayed as the sub-

picture.

VIDEO-1, -2, -3 or -4)

For the main picture:

Press the TV/VIDEO button.

Each time you press the button, the input

source changes as follows (the one used for

the sub picture will be skipped):

VIDEO-1 → VIDEO-2 → VIDEO-3 →

VIDEO-4 → TV

Pay attention to the following.

- When the VIDEO-2 or VIDEO-3

picture is a picture of 625p or 525p

signal, you cannot choose VIDEO-2

or VIDEO-3 with the SUB-P6

buttons.

For the sub picture:

- When the VIDEO-2 or VIDEO-3

picture signal is changed to 625p,

525p or 1125i signal while the

VIDEO-2 or VIDEO-3 picture is

displayed as the sub-picture, the

Twin or PIP modes is cancelled.

Press the

(Input) button.

Each time you press the button, the input

source changes as follow (the one used for

the main picture will be skipped):

VIDEO-1 → VIDEO-2 → VIDEO-3 →

VIDEO-4 → TV

„ Swapping the pictures

Press the

(Swap) button.

Each time you press the button, the main

picture and the sub picture will be swapped.

• The pictures cannot be swapped when

a picture of 625p or 525p signal from

VIDEO-2 or VIDEO-3 is being

displayed as the main picture.

Remote control buttons and functions

3 Choose the screen you want to view

The picture you choose changes to a

moving picture.

„ Changing the sub picture

position (in PIP mode only)

You can position the sub picture to one of

corners of the main picture.

9 pictures multi:

Choose by pressing 56.

Press the

(Position) button.

5 pictures multi:

Choose by pressing 6.

Each time you press the button, the sub

picture moves clockwise (lower right →

lower left → upper left → upper right).

4 Press the OK button

The multi-pictures disappears and the

chosen picture appears.

„ Setting the colour system of

the sub picture

Changing the multi-picture mode:

See “MULTI” on page 24.

You can choose the colour system of the

sub picture.

Cancelling the multi-pictures

Press the BACK button, CHANNELp

buttons, the number buttons or OK button.

The setting is performed with the “COLOUR

SYSTEM” menu (see page 23) when in the

Twin mode or PIP mode.

•

You can also enter this mode while in the

Twin mode, but not in the Text mode.

Multi-picture function

You can display multi-pictures that enable you

to easily find a program you want to view.

• Pictures will appear in the assigned

order in the PR LIST (PR01-99).

• The guarded channel with the

CHANNEL GUARD function will be

skipped and will not be displayed.

• Pictures from external devices cannot

be displayed in the 9-pictures multi

mode.

• In the 5-pictures multi mode, the

picture from external devices can only

be displayed as the main picture.

• In the 5 pictures multi mode, 1125i

signal cannot be displayed as the main

picture.

1 Set the PIP/TV/DVD switch to the PIP

position

2 Press the X button to display multi-

pictures

The channels are displayed in the

channel number order.

The multi-pictures will appear in one of

the two multi-picture modes.

9 pictures multi:

Still pictures

• The RETURN+ button is disabled in

the 9 pictures multi mode.

• In the multi-picture mode, the menu

cannot be displayed.

Moving picture

5 pictures multi:

• In the 5 pictures multi mode, the sound

in the moving picture can be listened

through the headphone.

Still pictures

Main picture

Moving picture

• To display the next multi-pictures,

press the X button.

Remote control buttons and functions

2 Press the STROBE button.

Eight consecutive still pictures which are

captured at intervals of about 0.2 second

are displayed in the order of “1” to “9”.

(These numbers are not actually

displayed.)

Freeze function

1 Set the PIP/TV/DVD switch to the PIP

position.

2 Press the

(Freeze) button.

Still picture is captured and displayed on

the right side of the screen. On the left,

the moving picture is displayed.

While watching a picture, you can

capture a still picture you want. The

captured still picture and the moving

picture are displayed at a time. (They are

the pictures of the same source.)

Still

picture

Moving

picture

To return to the normal screen:

Press the STROBE button again or press

the BACK button, the CHANNEL p

buttons or the number buttons.

• If signal level of the main picture is

weak, the still images become

abnormal.

To return to the normal screen:

Press the (Freeze) button again or

press the BACK button, the CHANNEL p

buttons or the number buttons.

• The

(Freeze) button do not work in

• The STROBE button do not work in the

Text mode, Twin mode, or PIP mode.

• The STROBE function does not work

for picture of 1125i signal.

• The menu cannot be displayed in the

STROBE mode.

the Text mode, Twin mode, or PIP

mode.

• The FREEZE function does not work

for picture of 1125i signal.

Strobe function

You can display eight consecutive still

pictures and one moving picture at a time.

(They are the pictures of the same source.)

1 Set the PIP/TV/DVD switch to the PIP

position.

Remote control buttons and functions

Operating a JVC brand DVD

player

You can operate a JVC brand DVD player.

Pressing the button having the same

appearance as the original remote control

button of a device makes the function work

in the same way as the original remote

control.

Viewing a teletext programme

1 Choose a TV channel with a teletext

broadcast.

2 Set the PIP/TV/DVD switch to the TV

position.

PIP

DVD

F.T/L

TOP MENU

3 Press P (Text) button to display the

teletext.

STROBE

Pressing P (Text) button changes the

mode as follows:

1 Set the PIP//TV/DVD Switch to the

DVD position

When you are operating the DVD player,

set the switch to the DVD position.

• You can turn the DVD player on or off

with the # (Standby) button.

TV and

Text mode

TV mode

• You can also press the MENU or TOP

MENU button and display the DVD

disc menu screen, and then operate by

pressing the 56 buttons.

Text mode

4 Choose a teletext page by pressing

the CHANNEL p buttons, number

buttons or colour buttons.

2 Press the DVD Control Button to

control your DVD player

• If your device is not made by JVC,

these buttons cannot be used.

• Even if your device is made by JVC,

some of these buttons or any one of

the buttons may not work, depending

on the device.

To return to the TV mode:

Press the P (Text), BACK or TV/VIDEO

button.

• If you have trouble receiving teletext

broadcasts, consult your local dealer

or the broadcast station.

• In the Text mode, the ZOOM mode is

fixed to the REGULAR mode.

• No menu operations are possible

when viewing a teletext programme.

• If characters on a teletext programme

do not appear properly, change the

TELETEXT LANGUAGE setting. For

details, see “TELETEXT LANGUAGE”

on page 34.

You cannot turn the TV on or off when the

PIP//TV/DVD switch is set to the DVD

position. When you turn the TV on or off,

set the PIP/TV/DVD switch to the TV or

PIP position.

Remote control buttons and functions

3 Press the

(Cancel) button to

return to a teletext page when the

page number is on the screen.

• You cannot return to the TV mode with

(Hold) button

You can hold a teletext page on the screen

for as long as you want, even while several

other teletext pages are being received.

the

(Cancel) button.

Press the

(Hold) button.

Sub-page

The (hold) are displayed at the top left

of the screen.

Some teletext pages include sub-pages that

are automatically displayed.

To cancel the Hold function:

1 Choose a teletext page that includes

sub-pages.

Press the

(Hold) button again.

Sub-page numbers that can be viewed

are automatically displayed at the top of

the screen.

(Reveal) button

Some teletext pages include hidden text

(such as answers to a quiz).

You can display the hidden text.

2 Press the 5 buttons to choose a

sub-page number.

Each time you press the

(Reveal)

button, text is hidden or revealed.

(Size) button

You can double the height of teletext

display.

Press the

(Size) button.

(Index) button

You can return to the index page instantly.

Press the (Index) button.

• In the List mode, you can return to the

page number displayed in the lower

left area of the screen.

(Cancel) button

You can search for a teletext page while

watching TV.

1 Press the number button to enter a

page number, or press the colour

button.

The TV searches for a teletext page.

2 Press the

(Cancel) button.

The TV programme appears. When the

TV finds the teletext page, its page

number appears in the upper left of the

screen.

Remote control buttons and functions

Using the List mode

You can store the numbers of your favorite

teletext pages in memory and call them up

quickly using the colour buttons.

To store the page numbers:

1 Press the F.T/L button to engage the

List mode.

The stored page numbers are displayed

at the bottom of the screen.

2 Press a colour button to choose a

position. Then press the number

buttons to enter the page number.

3 Press and hold down the

button.

(Store)

The four page numbers blink white to

indicate that they are stored in memory.

To call up a stored page:

1 Press the F.T/L button to engage the

List mode.

2 Press a colour button to which a page

has been assigned.

To exit the List mode:

Press the F.T/L button again.

Using the TV’s menu

This TV has a number of functions you can operate using menus.

To fully utilize all your TV’s functions, you need to understand the basic menu operating

techniques fully.

Buttons used to operate the menus

Types of menu

PICTURE menu

RETURN+

Choose to set the screen set-

tings.

D0106

D0107

D0108

FAVORITE CHANNEL

TV/VIDEO

SOUND menu

Choose to set the sound set-

tings.

SUB-P

TV/VIDEO

FEATURES menu

Choose to set the sleep timer

and child lock settings.

DISPLAY

BACK

SUB-P

CHANNEL

VOLUME

SET UP menu

1 Press the H button to display the

Choose to edit the channels

or set the display language

settings.

menu bar

D0109

PICTURE

The menu guide area can be made to

appear and disappear for some menus.

While the menu is displayed, press the

DISPLAY button to change between the

guide area being displayed and not

displayed.

D0105-EN

2 Press the 5 buttons to choose the

menu you want to use and then press

the a button

PICTURE

D1105-EN

Chosen

menu name

>> ZOOM

REGULAR

ZOOM

16:9

3 Press the 6 buttons to choose the

item to be set, press the 5 buttons

to set the item, and then press the a

button

D0017-EN

Guide area

If there are sub-menus, use the 7

buttons to operate them.

• Press the b button to return to

the previous menu.

• Press the TV/VIDEO or MENU button

to exit from the menu.

>> ZOOM

REGULAR

ZOOM

16:9

D1017-EN

• The guide area for some menus will

still be displayed even if the DISPLAY

button is pressed. This is not a

malfunction.

Using the TV’s menu

Operation with the buttons on the

PICTURE menu

PICTURE

You can also operate the menus using the

buttons on the front panel of the TV.

STANDARD

PICTURE MODE

CONTRAST

BRIGHT

SHARP

COLOUR

TINT

WHITE BALANCE

FEATURES

TV/VIDEO

button

buttons buttons

button

COOL

RESET

D0014-EN

„ PICTURE MODE

You can choose one of three PICTURE

MODEs to adjust the picture settings

automatically.

CHANNEL

VOLUME TV/VIDEO

EXIT

• The OK button acts as the MENU

button when the menu bar is not

displayed, and as the OK button when

the menu bar is displayed.

• Press the TV/VIDEO button to exit

from the menu.

BRIGHT:

Heightens contrast and sharpness.

STANDARD:

Standardizes picture adjustment.

SOFT:

Softens contrast and sharpness.

„ Adjusting the picture

You can change the picture settings of each

picture mode, as you like. The picture

settings changed are stored in the picture

mode.

CONTRAST

You can adjust the picture contrast.

2 : lower

3 : higher

BRIGHT

You can adjust the picture brightness.

2 : darker

3 : brighter

SHARP

You can adjust the picture sharpness.

2 : softer

3 : sharper

COLOUR

You can adjust the picture colour.

2 : lighter

3 : deeper

Using the TV’s menu

TINT

FEATURES menu

Choose FEATURES in the “PICTURE”

menu and press the a or 3 button to

display the sub-menu.

You can adjust the picture tint.

2 : reddish

3 : greenish

• You can change the TINT setting

(picture tint) only when the colour

system is NTSC 3.58 or NTSC 4.43.

> FEATURES

DIGITAL VNR

Super DigiPure

PULL DOWN

Colour DigiPure

COLOUR SYSTEM

ZOOM

AUTO(LOW)

AUTO

To return to the default settings in each

PICTURE MODE:

Press the blue button. This will return the

picture settings in the currently chosen

PICTURE MODE to the default settings,

and stores them in the PICTURE MODE

again.

MULTI

D1015-EN

„ DIGITAL VNR

„ WHITE BALANCE

The DIGITAL VNR function cuts down the

amount of noise in the original picture.

You can choose from the four DIGITAL

VNR function settings of AUTO(LOW),

AUTO(HIGH), MIN and MAX.

You can select one of three WHITE

BALANCE modes (three tones of white) to

adjust the white balance of the picture.

Since white is the colour which is used as a

reference for all the other colours, changing

the WHITE BALANCE mode affects the

appearance of all the other colours on the

screen.

AUTO(LOW)/AUTO(HIGH):

The TV will automatically adjust the level of

the DIGITAL VNR effect to match the

amount of noise in the picture, giving you

the best possible picture.

COOL:

A bluish white. Using this mode when

watching bright pictures allows you to enjoy

a more vivid and bright picture.

• If you set the DIGITAL VNR effect too

high it can make the picture less

sharp. It is recommended to use the

AUTO(LOW) setting if you can. If you

set the DIGITAL VNR function to

AUTO(LOW)but still notice some

noise, change the setting from

MID:

The normal white colour.

WARM:

A radish white. Using this mode when

watching films allows you to enjoy colours

that are characteristic of films.

AUTO(LOW) to AUTO(HIGH).

MIN:

The level of the DIGITAL VNR effect is set

to the minimum. If you set the DIGITAL

VNR function to AUTO(LOW) but feel that

the sharpness of the original picture has not

been reproduced fully, change the setting

from AUTO(LOW) to MIN.

• The MIN setting is not suitable for low-

quality pictures which contain a lot of

noise.

Using the TV’s menu

MAX:

MIN:

The level of the DIGITAL VNR effect is set

to the maximum. If you set the DIGITAL

VNR function to AUTO(HIGH) but still notice

some noise, change the setting from

AUTO(HIGH) to MAX.

The level of DigiPure effect is set to the

minimum. When you set the Super DigiPure

function to AUTO and notice some noise,

change the setting from AUTO to MIN.

• The MIN setting is not suitable for

high-quality pictures which contain

very little noise.

• The MAX setting is not suitable for

high-quality pictures which contain

very little noise.

MAX:

The level of DigiPure effect is set to the

maximum. If you set the Super DigiPure

function to AUTO but feel that the original

picture quality has not been reproduced

fully, change the setting from AUTO to

MAX.

„ Super DigiPure

The Super DigiPure function uses the latest

in digital technology to give you a natural-

looking picture. The Super DigiPure

function includes the following two

functions.

• The MAX setting is not suitable for

low-quality pictures which contain a lot

of noise.

DigiPure function:

This function helps to create a natural-

looking picture by eliminating unnecessary

edges from high-contrast and crisp images.

For images with low-contrast, edges are

added to produce a sharper, more detailed

picture.

OFF:

The Super DigiPure function is turned off.

„ PULL DOWN

The PULL DOWN function displays a

cinema film picture more smoothly and

naturally on the screen.

You can choose from the three DigiPure

function settings of AUTO, MIN and MAX.

• If you set the DigiPure effect too high

on a low-quality picture that contains a

lot of noise, this may actually make

the noise worse. We recommend you

use the AUTO setting if you can.

AUTO:

This function is turned on. Normally keep

this function set to AUTO.

ON :

This function is turned on.

Picture motion compensation function:

This function displays fast-moving pictures

(for example, the players or ball in a football

game) more smoothly and naturally on the

screen.

OFF:

This function is turned off.

• The motion may appear unnatural

when viewing images with the NTSC

colour system. To make the motion

smoother, switch the PULL DOWN

function from AUTO or ON to OFF.

• The effect level of the picture motion

compensation function cannot be

changed. The effect level is the same

no matter which of the AUTO, MIN or

MAX settings is used.

AUTO:

The TV will automatically adjust the level of

the DigiPure effect to match the amount of

noise in the picture, giving the best possible

picture.

Using the TV’s menu

SECAM:

SECAM system

„ Colour DigiPure

Makes the colour outline stand out and

increases the sharpness giving a clearer

picture.

NTSC 3.58:

NTSC 3.58 MHz system

ON:

NTSC 4.43:

NTSC 4.43 MHz system

Colour DigiPure works. Normally use with

this function turned on.

AUTO:

OFF:

This function detects a colour system

Colour DigiPure doesn’t work. This gives a

less clear picture than when this function is

turned on.

from the input signal.

• The AUTO function may not function

properly if you have poor signal

quality. If the picture is abnormal in

the AUTO function, choose another

colour system manually.

„ COLOUR SYSTEM

The colour system is chosen automatically.

However, if the picture is not clear or no

colour appears, choose the colour system

manually.

For colour system in your country or

region, refer to the table below:

Area

Country or Region

System

1 Choose COLOUR SYSTEM. Then

press the a or 3 button

Bahrain, Kuwait, Oman,

Qatar, United Arab Emirates,

Yemen, etc.

The sub-menu of the COLOUR SYSTEM

function appears.

PAL

Indonesia, Malaysia,

Singapore, Thailand, India,

etc.

China, Vietnam, etc.

Hong Kong, etc.

>> COLOUR SYSTEM

Asia,

Middle

East

PAL

MAIN

SUB

PAL

AUTO

Islamic Republic of Iran,

Lebanon, Saudi Arabia, etc.

SECAM

Philippines, Taiwan,

Myanmar, etc.

NTSC

Russia, etc.

SECAM

D0016-EN

Czech Republic, Poland, etc. PAL

2 Press the 5 buttons to choose

Europe

Germany, Holland, Belgium,

PAL

MAIN or SUB

etc.

UK, etc.

MAIN:

Oceania Australia, New Zealand, etc. PAL

Republic of South Africa, etc. PAL

You can change the colour system of the

main-picture.

Africa

Nigeria, etc.

PAL

SUB:

Egypt, Morocco, etc.

SECAM

You can change the colour system of the

sub-picture.

• Choose MAIN when a sub-picture is

not displayed.

3 Press the 6 buttons to choose the

appropriate colour system. Then

press the a button

PAL:

PAL system

Using the TV’s menu

„ ZOOM

SOUND menu

You can change the screen size according

to the picture aspect ratio. Choose the

optimum one from three ZOOM modes.

SOUND

STEREO/

SOUND MODE

BALANCE

HEADPHONE VOLUME

CINEMA SURROUND

SUPER BASS

MONO

1 Choose ZOOM, then press the OK or

MONO

LOW

3 button.

BBE DIGITAL

>> ZOOM

OSD-3-EN

REGULAR

ZOOM

16:9

• Functions in the “SOUND” menu other

than “HEADPHONE VOLUME” work

for the TV speakers. They do not work

for the sound from the headphones.

• When the headphones are connected

and only one screen is displayed,

“STEREO/I•II” and “HEADPHONE

VOLUME” can be used.

D0017-EN

2 Press the 6 buttons to choose a

ZOOM mode. Then press the OK

button.

• You can choose a ZOOM mode from

REGULAR, ZOOM or 16:9 modes. For

details, see “ZOOM button” on page 9.

„ STEREO / I•II

When you are viewing a bilingual broadcast

programme, you can choose the sound

from Bilingual I (sub I) or Bilingual II (sub II).

When the stereo broadcasting is received

poorly, you can change from stereo to mono

sound so that you can hear the broadcast

more clearly and easily.

„ MULTI

Choosing the number of pictures for the

Multi-picture function.

1 Choose MULTI, then press the OK or

3 button.

s : Stereo sound

>> MULTI

: mono sound

: Bilingual I (sub I)

: Bilingual II (sub II)

OSD-2-EN

MONO: Cancels the Multi Sound function,

and the sound becomes monaural.

• The sound mode you can choose

differs depending on the TV

programme.

2 Press the 5 buttons to choose the

number of pictures. Then press the

OK button.

• This function does not work in the

VIDEO modes.

Using the TV’s menu

„ SOUND MODE

„ HEADPHONE VOLUME

SOUND MODE USER.

Adjust the volume of the sub-picture sound

which is heard through the headphones

when set to Twin mode, PIP mode or 5

pictures multi.

1 Choose SOUND MODE, then press the

OK or 3 button.

2 :Reduce volume

3 :Increase volume

The “SOUND MODE“ menu appears.

• When not set to Twin mode or PIP

mode, the headphone volume is

adjusted with the r q (volume)

buttons.

> SOUND MODE

NEWS

„ CINEMA SURROUND

You can enjoy Surround sound with a “live”

effect by using the CINEMA SURROUND

function.

120Hz

500Hz

1.5kHz

5kHz

10kHz

SOUND MODE

• You can choose a CINEMA SURROUND

mode from HIGH, LOW, MONO and OFF

modes. For details, see “CINEMA

SURROUND button” on page 9.

• You can also operate the CINEMA

SURROUND function with the

CINEMA SURROUND button. For

details, see “CINEMA SURROUND

button” on page 9.

OSD4-EN

2 Press the red button and choose your

preferred SOUND MODE.

3 Press the 5 buttons and choose the

frequency to adjust, then press the

6 buttons and adjust the frequency.

• The adjusted frequency is registered

to USER.

„ SUPER BASS

• When DYNAMIC, MUSIC, or NEWS is

chosen and the frequency is adjusted,

the SOUND MODE automatically

changes to USER.

• Adjust the other frequencies

according to your preference.

• After adjusting the frequencies in step

3, pressing the blue button will return

to the SOUND MODE pattern chosen

in step 2.

You can choose the SUPER BASS mode

which emphasizes the bass sound.

• You can choose HIGH, MID or LOW.

Choosing LOW will reduce the bass

sound and choosing HIGH will

increase the bass sound.

• You can also operate the SUPER

BASS function with the BASS button.

For details, see “BASS button” on

page 10.

• You can choose a SOUND MODE

function with the SOUND MODE

button. For details, see “SOUND

MODE button” on page 10.

„ BBE DIGITAL

You can use the BBE DIGITAL function to

enjoy easy-to-listen sound that is faithful to

the original sound recorded.

„ BALANCE

• You can choose ON or OFF.

• Licensed by BBE Sound, Inc. BBE is a

registered trademark of BBE Sound, Inc.

You can adjust the volume balance

between the left and right speakers.

2 : turn the left speaker’s volume level up.

3 : turn the right speaker’s volume level up.

Using the TV’s menu

FEATURES menu

FEATURES

„ CHANNEL GUARD

When there is a TV channel you do not

want your children to watch, you can lock

out the channel. Even when a child chooses

a programme number for a locked out

channel the screen will change to blue and

display n so the channel cannot be viewed.

SLEEP TIMER

CHANNEL GUARD

APPEARANCE

BLUE BACK

CHILD LOCK

AUTO SHUTOFF

FAVORITE SETTING

TYPE A

OFF

OSD-5-EN

To set this function:

1 Choose CHANNEL GUARD, then

press the number 0 button.

„ SLEEP TIMER

You can set the TV to automatically turn off

after a set time.

> SET ID NO.

0040

1 Choose SLEEP TIMER, then press the

OK or 3 button.

> SLEEP TIMER

D0025-EN

120

2 Set the ID number you want.

OFF

To choose a number:

Press the 6 buttons.

To move a cursor:

D0024-EN

Press the 5 buttons.

2 Press the 5 buttons to set the

period of time.

3 Press the OK button.

>> CHANNEL GUARD

The TV begins count down from the set

time.

• You can set the period of time a

maximum of 120 minutes (2 hours) in

10 minute steps.

To cancel this function:

• Press the 2 button to set a period of

time to “OFF”.

GUARD

D0026-EN

3 Press the OK button to complete the

setting.

4 Press the 6 buttons to choose a TV

channel.

The menu disappears.

• One minute before this function turns

off the TV, “GOOD NIGHT!” appears.

• This function cannot be used to turn off

the TV’s main power.

• When this function is on, you can

display the SLEEP TIMER menu again

to confirm or change the remaining

time.

• The TV shows the TV programme

which the chosen TV channel is now

broadcasting.

5 Press the blue button to set this

function to the TV channel.

n (CHANNEL GUARD) appears and the

TV channel is locked.

Using the TV’s menu

To cancel this function:

„ BLUE BACK

Press the blue button again.

n (CHANNEL GUARD) disappears and

the lock is released.

You can set the TV to automatically change

to a blue screen and mute the sound if the

signal is weak or absent, or when there is

no input from an external device.

6 Press the OK button to complete the

setting.

ON:

The menu disappears.

This function is turned on.

To view a locked TV channel:

OFF:

1 Choose a programme number in

which a TV channel locked with the

number buttons or PR LIST.

This function is turned off.

„ CHILD LOCK

The screen changes to blue and the n

(CHANNEL GUARD) appears.

You can disable the front control buttons of

the TV. When this function is set to ON, the

TV can be operated only by using the

remote control.

D0027-EN

• You cannot choose a locked TV channel

with the CHANNEL p buttons.

Use this function to prevent children from

operating the TV at their own discretion

(without parent consent).

2 Press the DISPLAY button to display

“ID NO.” (ID number input screen).

ON:

This function is turned on.

OFF:

ID NO.

D0028-EN

This function is turned off.

Turning the power off with the main power

button cancels the CHILD LOCK.

3 Press the number buttons to enter the

ID number.

The lock is temporarily released so you

can view the TV channel.

„ AUTO SHUTOFF

You can set the power to turn off if no signal

is received and no operation is performed

for about 15 minutes or longer after the end

of a broadcast.

If you have forgotten the ID number:

Perform step 1 of “To set this function:” on

page 26. After confirming the ID number,

press the TV/VIDEO button to exit the menu.

ON:

• When you would like to cancel the

CHANNEL GUARD function, you must

perform the operation “To set this

function” again.

This function is turned on.

OFF:

This function is turned off.

• The AUTO SHUTOFF function does

not turn off the TV’s main power.

• The AUTO SHUTOFF will not work for

a VIDEO mode.

„ APPEARANCE

Press the 5 button and choose the

format in which the channel number is

displayed from the three types: TYPE A,

TYPE B and TYPE C.

Using the TV’s menu

• For details of each item, see

“PICTURE MODE” on page 20,

“DIGITAL VNR” on page 21, “WHITE

BALANCE” on page 21, “Super

DigiPure” on page 22.

„ FAVORITE SETTING

You can set a dedicated picture effect for

the favorite channels registered to the

colour buttons (Red, Green, Yellow and

Blue). For favorite channel registration, see

“Favorite channel registration” on page 11.

Item

Options

1 Choose FAVORITE SETTING, then

PICTURE MODE BRIGHT*, STANDARD,

SOFT

press the OK or 3 button.

DIGITAL VNR

AUTO (LOW)*, AUTO

(HIGH), MIN, MAX

> FAVORITE SETTING

FAVORITE CH SETTING

VIDEO SETTING

WHITE

BALANCE

COOL, MID*, WARM

OSD-6-EN

Super DigiPure AUTO*, MAX, OFF, MIN

PICTURE

EFFECT

ON*:

2 Choose FAVORITE CH SETTING, then

Above picture effect

applies to the chosen

favorite channel.

OFF:

press OK or 3 button.

>> FAVORITE CH SETTING

FAVORITE CHANNEL

RP 06

No picture effect applies.

PICTURE MODE

DIGITAL VNR

WHITE BALANCE

Super DigiPure

PICTURE ADJUST

BRIGHT

AUTO(LOW)

COOL

OFF

*: When shipped

• Pressing the blue button returns each

setting back to initial setting and cancels

the favorite channel registration.

RESET

OSD-7-EN

5 Press the OK button to complete the

setting.

3 Press the 6 button to choose

FAVORITE CHANNEL, then press the

5 button to choose the registered

favorite channel.

„ VIDEO SETTING

You can set a dedicated picture effect for

the video inputs, VIDEO-1 to -4.

Each time you press the 5 button, the

colour button icon (Red, Green, Yellow

or Blue) of the registered favorite

channel and its channel number (e.g.

PR1) appear.

1 Choose FAVORITE SETTING, then

press the OK or 3 button.

2 Choose VIDEO SETTING, then press

the OK or 3 button.

4 Set the picture effect.

>> VIDEO SETTING

Press the 6 button to choose an item

listed in the following table and press the

5 button to choose one of options.

• As explained in the table, if PICTURE

EFFECT is set to OFF, the dedicated

picture effect for the favorite channel is

not used. In this case, normal picture

effect is used.

VIDEO

VIDEO-1

BRIGHT

AUTO(LOW)

COOL

AUTO

PICTURE MODE

DIGITAL VNR

WHITE BALANCE

Super DigiPure

PICTURE ADJUST

RESET

OSD-8-EN

Using the TV’s menu

3 Press the 6 button to choose

VIDEO, then press the 5 button to

choose one of video inputs, VIDEO-1

to -4.

SETUP menu

SET UP

AUTO PROGRAM

EDIT/MANUAL

LANGUAGE

4 Set the picture effect.

PICTURE TILT

VIDEO-2 SETTING

VIDEO-3 SETTING

AI VOLUME

COMPONENT

Press the 6 button to choose an item

listed in the following table and press the

5 button to choose one of options.

• As explained in the table, if PICTURE

EFFECT is set to OFF, the dedicated

picture effect for the video inputs is not

used. In this case, normal picture

effect is used.

TELETEXT LANGUAGE

OSD-9-EN

„ AUTO PROGRAM

You can automatically register the TV

channels which can be received well at your

residence in the TV’s programme numbers

by performing the following.

Item

Options

PICTURE MODE BRIGHT*, STANDARD,

SOFT

1 Choose AUTO PROGRAM, then press

the OK button.

The AUTO PROGRAM function starts.

The TV channels you receive are

automatically stored in the programme

numbers list.

DIGITAL VNR

AUTO (LOW), AUTO

(HIGH), MIN*, MAX

WHITE

BALANCE

COOL, MID*, WARM

>> AUTO PROGRAM

Super DigiPure AUTO, MAX*, OFF, MIN

CH 28

PICTURE

EFFECT

ON*:

14%

Above picture effect

applies to the chosen

video input.

OFF:

D0004-EN

No picture effect applies.

• To stop the AUTO PROGRAM

function, press the OK button.

*: When shipped

• For details of each item, see

“PICTURE MODE” on page 20,

“DIGITAL VNR” on page 21, “WHITE

BALANCE” on page 21, “Super

DigiPure” on page 22.

2 After the TV channels have been

stored in the programme number list,

the EDIT menu appears.

> EDIT

• When the signal is 625p or 525p:

- In “DIGITAL VNR”, AUTO

(LOW and HIGH) cannot be selected.

- In “Super DigiPure”, AUTO cannot be

selected.

CH/CC

• Pressing the blue button will return the

picture effect to the factory set value.

MANUAL

MOVE

INSERT DELETE

D0038-EN

5 Press the OK button to complete the

setting.

Using the TV’s menu

• You can proceed to edit the

programme numbers list using the

EDIT/MANUAL function. For details,

see “EDIT/MANUAL” on page 30

• If a TV channel you want to view is not

stored in the programme numbers list,

you can register it using the MANUAL

function.

1 Choose EDIT/MANUAL, then press the

OK or 3 button.

> EDIT

CH/CC

For details, see “EDIT/MANUAL” on

page 30.

MANUAL

MOVE

INSERT DELETE

• The AUTO PROGRAM function does

not store a TV channel to the

programme number 0 (AV).

• If you do not need to use the EDIT/

MANUAL function, press the OK

button to exit the EDIT menu.

• Starting the AUTO PROGRAM deletes

the registered favorite channel.

D0038-EN

2 Follow the operation description of a

function you want to use and operate

the function.

MOVE:

This function changes a programme

number of a TV channel.

ID:

This function registers a Channel name

(ID) to a TV channel.

„ EDIT/MANUAL

The EDIT/MANUAL functions are divided

into two types: editing of the current

programme numbers (EDIT functions) and

manual registration of a TV channel you

want to view to the programme number

(MANUAL function).

INSERT:

This function adds a new TV channel in

the current programme numbers list by

using the CH/CC number.

DELETE:

This function deletes an unnecessary TV

Channel.

CAUTION

• Using the MOVE, DELETE or INSERT

function rewrites the current programme

numbers list.

Resultingly, the programme number of

some of the TV channels will change.

• When a TV channel which has been

locked out using the CHANNEL GUARD

function, using the MANUAL function for

that TV channel cancels the CHANNEL

GUARD function.

MANUAL:

This function manually registers a new

TV channel in a programme number.

3 Press the OK button to complete the

setting.

• For programme number PR 0, “AV”

appears in the programme numbers

list.

• When a TV channel has already been

registered in PR 99, using the INSERT

function deletes the TV channel.

Using the TV’s menu

To cancel the ID function:

FUNCTIONS

MOVE

Press the BACK button.

4 Press the OK button to register a

channel name to a TV channel.

1 Press the 6 buttons to choose a TV

channel.

DELETE

2 Press the 3 button to start the MOVE

1 Press the 6 buttons to choose a TV

function.

channel.

> EDIT

2 Press the yellow button to delete the

TV channel.

CH/CC

CH 21

The TV channel is deleted from the

programme numbers list.

MANUAL

1 Press the 6 buttons to choose a

programme number to which you

want to register a new TV channel.

STORE

D0030-EN

2 Press the blue button to activate the

MANUAL function.

3 Press the 6 buttons to choose a

new programme number.

At the right side following the CH/CC

number, the SYSTEM (sound system) of

the TV channel appears.

To cancel the MOVE function:

Press the BACK button.

4 Press the 2 button to change the

programme number of a TV channel

to a new programme number.

> MANUAL

CH/CC

01 (

BBC1

1 Press the 6 buttons to choose a TV

channel.

)

B / G

2 Press the red button to start the ID

function.

SEARCH+

FINE-

SYSTEM

FINE+

SEARCH-

3 Enter a channel name (ID). Press the

6 buttons to choose a character.

Press the 5 buttons to move the

cursor.

D0035-EN

To cancel the MANUAL function:

Press the BACK button.

> EDIT

CH/CC

D0032-EN

Using the TV’s menu

3 Press the 3 button to choose the

system (sound system) for a TV

channel you want to register.

6 Press the OK button and register the

TV channel to a programme number.

The normal EDIT menu is resumed.

• For the sound systems in each country

or region, refer to the table below:

INSERT

Preparation:

• Find the CH/CC number

corresponding to the channel number

of the TV channel from page 35.

Area

Country or Region

System

B/G

Bahrain, Kuwait, Oman,

Qatar, United Arab Emirates,

Yemen, etc.

Indonesia, Malaysia,

Singapore, Thailand, India,

etc.

1 Press the 6 buttons to choose a

programme number for which you will

Asia,

Middle

East

China, Vietnam, etc.

Hong Kong, etc.

Islamic Republic of Iran,

Lebanon, Saudi Arabia, etc.

Philippines, Taiwan,

Myanmar, etc.

Russia, etc.

Czech Republic, Poland, etc. D/K

Germany, Holland, Belgium,

D/K

2 Press the green button to start the

INSERT function.

B/G

> EDIT

CH/CC

D/K

Europe

B/G

etc.

UK, etc.

Oceania Australia, New Zealand, etc. B/G

CH/CC

D0034-EN

Republic of South Africa, etc.

Nigeria, etc.

Egypt, Morocco, etc.

3 Press the 6 buttons to choose “CC”

or “CH” according to the CH/CC

number of the TV channel.

Africa

B/G

4 Press the green or red button to

search for a TV channel.

To cancel the INSERT function:

Press the BACK button.

Scanning stops when the TV finds a TV

channel. Then the TV channel is

displayed.

4 Press the Number buttons to enter the

remaining CH/CC number.

The TV shifts to registration mode. When

the registration is completed, the picture

of the TV channel appears on the

screen.

5 Press the green or red button

repeatedly until the TV channel you

want appears.

If the TV channel reception is poor:

Press the blue or yellow button to fine-

tune the TV channel.

If you cannot hear the normal sound

even when the picture of the TV

channel appears normally:

The SYSTEM setting is wrong. Press the

3 button and choose a SYSTEM that has

normal sound.

Using the TV’s menu

• The CH/CC number is a number

indicating the broadcast frequency to

the TV. If the TV cannot detect the TV

channel corresponding to the

broadcast frequency indicated by the

CH/CC number, a picture in the no-

signal state appears.

„ VIDEO-2 SETTING/VIDEO-3

SETTING

Set the VIDEO-2 SETTING or VIDEO-3

SETTING correctly according to the video

signal input from the external device

connected to the VIDEO-2 or VIDEO-3

terminal. If this setting is incorrect, images

will not be displayed.

„ LANGUAGE

VIDEO:

You can choose the language you want to

use for the on-screen display from the

language list in a menu.

If a normal video signal (composite video

signal) is input.

1 Choose LANGUAGE, then press the

OK button.

COMPONENT:

If a Component video signal (Y, Cb/Pb,

Cr/Pr signals) is input.

• For detailed connecting methods, see

“Additional preparation” on page 36.

This Television is compatible with the

1125i, 625p or 525p video signal only

when the component video signal is

input.

• When the input signal is 1125i, 625p or

525p, each signal type is displayed at

the upper right side on the TV screen

by setting the input to VIDEO-2 or

VIDEO-3.

2 Press the 6 buttons to choose a

language.

3 Press the OK button to complete the

setting.

The menu disappears.

„ AI VOLUME

„ PICTURE TILT

You can prevent the sudden increase or

decrease of sound that occurs when

changing the channel to another channel or

switching the VIDEO mode to another

VIDEO mode.

There are cases where the Earth’s

magnetic force may make the picture tilt. If

this happens, you can correct the picture tilt.

1 Choose PICTURE TILT, then press the

OK or 3 button.

ON:

> PICTURE TILT

This function is turned on.

OFF:

This function is turned off.

• The AI VOLUME function may not

operate as expected if the sound input

level from a broadcast station (or video

software) is extremely low.

• When the Video or the DVD is used, it

is recommended to select OFF to get

more dynamic sound.

D0018-EN

2 Press the 6 buttons until the

picture becomes level. Then press the

OK button.

Using the TV’s menu

3 Press the OK button to complete the

setting.

„ TELETEXT LANGUAGE

There are four types of teletext language

groups. Set the teletext language group that

corresponds to the language of the teletext

program that you want to watch.

The menu disappears.

• Languages that are not included in the

teletext language group that you

select, the sub-titles of the teletext

program will not be displayed properly.

1 Choose TELETEXT LANGUAGE, then

press the OK or 3 button.

> TELETEXT LANGUAGE

GROUP-1

GROUP-2

GROUP-3

GROUP-4

OSD-10-EN

2 Press the 6 buttons to choose a

group.

Group

Languages

GROUP-1 Turkish, Hungarian, English,

German, French, Italian,

Spanish, Portuguese, Greek,

Swedish, Finnish

GROUP-2 Polish, Serbian, Croatian,

Slovenian, Czech, Slovak,

Rumanian, Hungarian,

German, French, Italian,

Swedish, Finnish

GROUP-3 Russian, Bulgarian, Lettish,

Lithuanian, Estonian,

Ukrainian, Serbian, Croatian,

Slovenian, Czech, Slovak,

English, German

GROUP-4 Arabic, Czech, Slovak.

Hungarian, English, German,

French, Italian, Spanish,

Portuguese, Swedish, Finnish

Using the TV’s menu

CH/CC number

When you want to use the INSERT function on page 32, find the CH/CC number

corresponding to the Channel number of the TV channel from this table.

US: The US channel numbers are the channel numbers used in the United States,

Philippines, etc. CCIR: The CCIR channel numbers are the channel numbers used in the

Middle East, Southeast Asia, etc. OIRT: The OIRT channel numbers are the channel

numbers used in Eastern Europe, Russia, Vietnam, etc. AUSTRALIA: The AUSTRALIA

channel numbers are the channel numbers used in Australia, etc.

Channel

US-2

US-3

US-4

US-5

US-6

US-7

US-8

US-9

US-10

US-11

US-12

US-13

CCIR

OIRT

AUSTRALIA

AU-0

AU-1

AU-2

AU-6

AU-7

AU-8

AU-9

CCIR

S-1

S-2

S-3

S-4

S-5

S-6

S-7

S-8

OIRT

AUSTRALIA

AU-5

CH 02

CH 03

CH 04

CH 05

CH 06

CH 07

CH 08

CH 09

CH 10

CH 11

CH 12

CH 13

CH 14

CH 15

CH 16

CH 17

CH 18

CH 19

CH 20

CH 21

CH 22

CH 23

CH 24

CH 25

CH 26

CH 27

CH 28

CH 29

CH 30

CH 31

CH 32

CH 33

CH 34

CH 35

CH 36

CH 37

CH 38

CH 39

CH 40

CH 41

CH 42

CH 43

CH 44

CH 45

CH 46

CH 47

CH 48

CH 49

CH 50

CH 51

CH 52

CH 53

CH 54

CH 55

CH 56

CH 57

CH 58

CH 59

CH 60

CH 61

CH 62

CH 63

CH 64

CH 65

CH 66

CH 67

CH 68

CH 69

CC 01

CC 02

CC 03

CC 04

CC 05

CC 06

CC 07

CC 08

CC 09

CC 10

CC 11

CC 12

CC 13

CC 14

CC 15

CC 16

CC 17

CC 18

CC 19

CC 20

CC 21

CC 22

CC 23

CC 24

CC 25

CC 26

CC 27

CC 28

CC 29

CC 30

CC 31

CC 32

CC 33

CC 34

CC 35

CC 36

CC 37

CC 38

CC 39

CC 40

CC 41

CC 42

CC 43

CC 44

CC 45

CC 46

CC 47

CC 48

CC 49

CC 50

CC 51

CC 52

CC 53

CC 54

CC 55

CC 56

CC 57

CC 58

CC 59

CC 60

CC 61

CC 62

CC 63

CC 64

CC 75

CC 76

CC 77

CC 78

CC 79

CC 95

CC 96

CC 97

CC 98

CC 99

AU-5A

E10

E11

E12

R10

R11

R12

AU-10

AU-11

S-9

S-10

S-11

S-12

S-13

S-14

S-15

S-16

S-17

S-18

S-19

S-20

S-21

S-22

S-23

S-24

S-25

S-26

S-27

S-28

S-29

S-30

S-31

S-32

S-33

S-34

S-35

S-36

S-37

S-38

S-39

S-40

S-41

US-14, W+29

US-15, W+30

US-16, W+31

US-17, W+32

US-18, W+33

US-19, W+34

US-20, W+35

US-21, W+36

US-22, W+37

US-23, W+38

US-24, W+39

US-25, W+40

US-26, W+41

US-27, W+42

US-28, W+43

US-29, W+44

US-30, W+45

US-31, W+46

US-32, W+47

US-33, W+48

US-34, W+49

US-35, W+50

US-36, W+51

US-37, W+52

US-38, W+53

US-39, W+54

US-40, W+55

US-41, W+56

US-42, W+57

US-43, W+58

US-44, W+59

US-45, W+60

US-46, W+61

US-47, W+62

US-48, W+63

US-49, W+64

US-50, W+65

US-51, W+66

US-52, W+67

US-53, W+68

US-54, W+69

US-55, W+70

US-56, W+71

US-57, W+72

US-58, W+73

US-59, W+74

US-60, W+75

US-61, W+76

US-62, W+77

US-63, W+78

US-64, W+79

US-65, W+80

US-66, W+81

US-67, W+82

US-68, W+83

US-69, W+84

E21

E22

E23

E24

E25

E26

E27

E28

E29

E30

E31

E32

E33

E34

E35

E36

E37

E38

E39

E40

E41

E42

E43

E44

E45

E46

E47

E48

E49

E50

E51

E52

E53

E54

E55

E56

E57

E58

E59

E60

E61

E62

E63

E64

E65

E66

E67

E68

E69

W+1

W+2

W+3

W+4

W+5

W+6

W+7

W+8

W+9

W+10

W+11

W+12

W+13

W+14

W+15

W+16

W+17

W+18

W+19

W+20

W+21

W+22

W+23

W+24

W+25

W+26

W+27

W+28

Z+1

Z+2

AU-3

AU-4

A-5

A-4

A-3

A-2

A-1

Additional preparation

„ Connecting the external

devices

Connect the devices to the TV, paying

attention to the following connection

diagram.

HV-Z34L1

HV-Z29V1

Before connecting anything:

• Read the manuals provided with the

devices. Depending on the devices,

the connection method may differ from

the figure. In addition, the device

settings may be changed depending

on the connection method to secure

proper operation.

(Behind the cover)

• Turn off all the devices including the

TV.

• The “Specifications” on page 43

contains the details of the VIDEO

terminals. If you are connecting a

device not listed in the following

connection diagram, see the

“Specifications” to choose the best

VIDEO terminal.

OVER

L/MONO

IN (VIDEO-4)

• Note that connecting cables are not

supplied.

1 VCR (composite signal)

2 VCR (S-VIDEO signal; Y/C)

3 VCR for recording (composite signal)

4 DVD player (composite signal)

5 DVD player (S-VIDEO signal; Y/C)

6 DVD player (component video signals;

Y, Cb/Pb, Cr/Pr)

Back of the TV

7 TV game (composite signal)

8 TV game (S-VIDEO signal; Y/C)

9 Camcorder (composite signal)

0 Camcorder (S-VIDEO signal; Y/C)

- Headphones

Additional preparation

If connecting a device to the VIDEO-2

(COMPONENT) or VIDEO-3 (COMPONENT)

terminal with a video cable.

Connect the TV’s VIDEO jack and the

device’s VIDEO OUT (video output) jack

with a video cable.

Then set the VIDEO-2 SETTING or VIDEO-

3 SETTING to VIDEO according to “VIDEO-

2 SETTING/VIDEO-3 SETTING” on

page 33.

Connecting methods

1 Connect the TV’s VIDEO jack and the

device’s VIDEO OUT (video output)

jack with a video cable.

If connecting a device to the TV with an

S-VIDEO cable:

Connect the VCR’s S-VIDEO OUT (S-

VIDEO output) connector and the TV’s S

connector with an S-VIDEO cable, instead

of connecting with a video cable.

Note that the connection with a video cable

will be ignored in case you connect a VCR

to the TV with both video cable and S-

VIDEO cable.

• In the VIDEO-4 terminal, the VIDEO

jack is indicated by “V”.

2 Connect the TV’s AUDIO jacks (L/

MONO and R) and the device’s AUDIO

OUT (audio L/R output) jacks with an

audio cable.

If connecting a DVD player to the TV with

a component video cable.

If the device’s sound output is in mono:

Connect the device’s AUDIO OUT jack and

the TV’s L/MONO jack with an audio cable.

Connect three jacks (Y, Cb/Pb, Cr/Pr) in the

VIDEO-2 or VIDEO-3 terminal and the DVD

player’s COMPONENT (component video

output) jacks with a component video

cables, instead of connection with a video

cable. Then set the VIDEO-2 SETTING/

VIDEO-3 SETTING to COMPONENT,

according to “VIDEO-2 SETTING/VIDEO-3

SETTING” on page 33.

Connecting devices to the

OUTPUT terminal

The signals of the images and sound you

are currently viewing with this TV are output

through the OUTPUT terminal. By

connecting a VCR to the OUTPUT terminal,

you can record the currently shown image

and sound to that VCR. To do this, connect

the VCR and OUTPUT terminal following

the steps below.

• If you have a DVD player that outputs

1125i, 625p or 525p video signals as a

component video signal, then by

attaching the device to the television

with a component video cable you can

see the actual images that are

1 Connect the VIDEO jack in the

OUTPUT terminal and the VCR’s

VIDEO IN (video input) jack with a

video cable.

recorded on a DVD disc as an original

image source.

2 Connect the AUDIO jacks (L and R) in

the OUTPUT terminal and the VCR’s

AUDIO IN (audio L/R input) jacks with

an audio cable.

• When you turn off the TV, the signals

from the OUTPUT terminal are also

turned off.

• The component signals input from the

VIDEO-2 (COMPONENT) or VIDEO-3

(COMPONENT) terminal cannot be

output through the OUTPUT terminal.

Additional preparation

Connecting Headphones

Connect the headphones with a stereo

mini jack (of 3.5 mm in diameter) to the

Headphone jack at the TV front panel.

Conditions to use the AV COMPU

LINK remote control system

• A device equipped with an AV COMPU

LINK terminal is required.

• You must connect the TV and the

device with an AV COMPU LINK cable.

AV COMPU LINK cable is not supplied

with this TV. If an AV COMPU LINK

cable is unavailable, connect them with

a cable with dia. 3.5 mm (mono) male

plugs at both ends.

• You must connect the device to an

appropriate VIDEO terminal and set it

up correctly. Otherwise the AV

COMPU LINK remote control system

will not function correctly. For details,

see “Setting up the AV COMPU LINK

remote control system”.

• The TV must be in standby mode (the

POWER lamp lighting red). If the TV’s

Main power is off (the POWER lamp

off), the AV COMPU LINK remote

control system does not function.

„ Connecting AV COMPU LINK

Supported Devices

AV COMPU LINK remote control system is

a system in which related devices are

automatically controlled when you operate

one device.

If you apply this system to the TV, you can

have the TV automatically perform the

required operations by operating one

external device. You don’t have to use the

TV’s remote control to turn on the TV or

change the VIDEO modes.

Examples of the AV COMPU LINK

remote control system

operations

Simply by pressing the PLAY button on a

VCR or a DVD player, you can view images

from the device.

Simply by inserting a prerecorded tape (a

tape with the record safety tab removed) to

a VCR, you can view the tape.

Simply by operating the AV Control

Receiver, you can have the TV turned on/off

(in standby mode) or the VIDEO mode

changed correctly.

Setting up the AV COMPU LINK

remote control system

CAUTION:

• With some devices, the setup method

differs from the ones explained here. Be

sure to read the device’s instruction

manual thoroughly before setting it up.

• The performance of the AV COMPU

LINK remote control system varies

depending on the connected device.

See the device’s instruction manual.

• When you select “TV SOUND” as the

input source with the AV Control

Receiver, there are cases where the

TV’s MUTING function automatically

operates and the sound from the TV’s

speakers is muted.

In such cases, press the VOLUME-/+

buttons or the MUTING button on the

TV’s remote control to cancel the

MUTING function. You can regain the

sound from the TV’s speakers.

1 Connect the device to the TV’s VIDEO-1,

VIDEO-2 (COMPONENT) or VIDEO-3

(COMPONENT) terminal.

If you want to connect a DVD player to

the TV with a component video cable:

Connect the DVD player to the TV’s

VIDEO-2 (COMPONENT) or VIDEO-3

(COMPONENT) terminal.

• For detailed connecting instructions,

see “Connecting the external devices”

on page 36.

2 Connect the TV’s AV COMPU LINK

terminal and the device’s AV COMPU

LINK terminal with an AV COMPU

LINK cable.

Additional preparation

3 Change the device’s setting

according to the VIDEO terminal it is

connected to.

If a VCR is connected to the VIDEO-1

terminal:

Set the VCR’s remote control code to A

code.

If a DVD player is connected to the

VIDEO-1 terminal:

Set the DVD player’s AV COMPULINK

MODE to DVD2.

If a VCR is connected to the VIDEO-2

(COMPONENT) terminal:

Set the VCR’s remote control code to B

code.

If a DVD player is connected to the

VIDEO-2 (COMPONENT) terminal:

Set the DVD player’s AV COMPULINK

MODE to DVD3.

If a DVD player is connected to the

VIDEO-3 (COMPONENT) terminal with a

component video cable:

Set the DVD player’s AV COMPULINK

MODE to DVD1.

• For instructions on how to change the

device’s setting, refer to the device’s

instruction manual.

• If the device you are connecting has

neither the remote control code nor the

AV COMPULINK MODE, then connect

it to the TV’s VIDEO-1 terminal.

Troubleshooting

If a problem arises while you are using the TV, please read this “Troubleshooting” well

before you request having the TV repaired. You may be able to fix it easily by yourself. For

example, if the AC plug is disconnected from the AC outlet, or the TV aerial has problems,

you may think there is a problem with the TV itself.

Important:

• This Troubleshooting guide only covers problems whose causes are not easy to

determine. If a question arise when you are operating a function, read the page(s)

corresponding to the operation of the function well, not this Troubleshooting guide.

• After you have followed the Troubleshooting description or the operating description of

the functions concerned without any success, remove the AC plug from the AC outlet

and request a repair of your TV. Do not attempt to repair the TV by yourself or remove

the rear cover of the TV.

„ If you cannot turn on the TV

• Is the AC plug connected to the AC

outlet?

„ Poor picture

• If noise totally obscures the picture

(snow), the aerial or aerial cable may

have trouble. Check the following to try

to solve the trouble:

• Is the POWER lamp lit? If not, press

the Main power button.

• Make sure to set the PIP/TV/DVD

switch to the TV or PIP position. You

cannot turn the TV on when the PIP/

TV/DVD switch is set to the DVD

position.

Has the TV and aerial been connected

properly?

Has the aerial cable been damaged?

Is the aerial pointed to the right

direction?

Is the aerial itself faulty?

„ If you cannot turn off the TV

• Make sure to set the PIP/TV/DVD

switch to the TV or PIP position. You

cannot turn the TV off when the PIP/

TV/DVD switch is set to the DVD

position.

• If the TV or aerial receives interference

from the other devices, stripes or noise

may appear in the picture. Move such

device as an amplifier, personal

computer, or a hair drier that can

cause interference away from your TV,

or try changing its location. If the aerial

suffers interference from a radio tower

or high-voltage wire, please contact

your local dealer.

• If the TV receives interferences from

signal reflecting from mountains or

building, double-pictures (ghosting) will

occur.

Try to change the aerial’s direction or

replace the antenna with the one with

better directionality.

„ No picture/No sound

• Have you chosen a TV channel whose

reception is extremely bad? In this

case, the BLUE BACK function will be

activated, the entire screen becomes

blue, and the sound is muted. In spite

of this, if you want to view the TV

channel, follow the description “BLUE

BACK” on page 27 to try to change the

BLUE BACK function setting to OFF.

• Are your SOUND SYSTEM settings for

the TV channels correct?

• Are your COLOUR SYSTEM settings

for the TV channels correct? Follow

the description “COLOUR SYSTEM”

on page 23 to try to solve the trouble.

Follow the description “EDIT/

MANUAL” on page 30 to use the

MANUAL function to try to change the

SYSTEM setting.

Troubleshooting

• Has COLOUR or BRIGHT been

controlled properly? Follow the

description “Adjusting the picture” on

page 20 to try to adjust them properly.

• Videotaping teletext is not

recommended because it may not

record correctly.

• When a white and bright still image

(such as a white dress) is displayed on

the screen, the white part may look as

if it were coloured.

It is a phenomenon unavoidable due to

the nature of the picture tube itself, and

not due to a TV failure.

When the picture disappears from the

screen, the unnatural colours will also

disappear.

• When viewing images from

commercially available video software

products, or videos from videotapes

which have been recorded improperly,

the top of the image may be distorted.

This is due to the condition of the video

signal, and not because of

„ Operation disabled

• Have the batteries of the remote

control become exhausted?

Follow the description “Putting the

batteries into the remote control” on

page 4 and replace them with new

batteries to try solve the problem.

• Have you attempted to use the remote

control at the sides or rear of the TV or

at a location more than seven meters

apart from the TV location? Operate

the remote control in the front of your

TV or a location less than seven

meters from your TV to try to solve the

problem.

• When you are viewing a teletext

programme, you cannot operate the

menus.

Press the BACK or TV/VIDEO button

to return the teletext programme to the

ordinary TV programme to try

operating the menus.

• Is the CHILD LOCK function set to

ON? If the CHILD LOCK function is set

to ON, you cannot operate the TV with

the front control buttons of the TV.

Follow the description “CHILD LOCK”

on page 27 to try to set the CHILD

LOCK function to OFF.

• If the TV operation becomes disabled

suddenly, press the Main power button

on the TV and turn off the main power.

Try to press the Main power button

again to turn on the main power. If the

TV returns to a normal state, it is not a

failure.

malfunction.

„ Poor sound

• When the TV channel reception is

poor, it can be hard to hear the stereo

or bilingual sound. In this case, follow

the description “STEREO / I•II” on

page 24 to hear the sound more easily

by changing it to a mono sound.

• The following functions do not operate

when receiving 1125i, video signal.

- Twin, PIP, Multi-display, FREEZE

and STROBE functions

Troubleshooting

• Touching the screen may cause you

feel a slight electric shock due to its

static electricity.

It is an unavoidable phenomenon due

to the construction of the picture tube.

It is not a problem with the TV.

You can rest assured that this static

discharge does not have harmful

influence over the human body.

„ Other concerns

• When the AUTO SHUTOFF function

operates, the TV is automatically

turned off.

If the TV is turned off suddenly, try to

press the # button to turn on the TV

once again. At this time, if the TV

resumes a normal state, there is no

problem.

• If you bring a magnetized device such

as a speaker near to your TV, a picture

may be warped or unnatural colours

appear at the corners of the screen. In

this case, keep the device apart from

your TV. If the speaker causes such

phenomena, use the magnetic-

shielded speaker instead.

• A picture may be tilted due to the

influence of the earth’s magnetism. In

this case, use the “PICTURE TILT” on

page 33 to complete the tilt.

• It takes a short period of time from the

time an operation such as changing

channels is performed until an image is

displayed. This is not a malfunction.

This is the time required for the image

to stabilize before it can be displayed.

• The TV may emit a crackling sound

due to a sudden change in

temperature. It does not matter if a

picture or sound does not show any

abnormality. If you hear crackling

sounds frequently while you are

viewing the TV, other causes may be

assumed.

For precautionary purposes, request

your service technician to inspect it.

Specifications

Broadcasting systems

Colour systems

B, G, I, D, K, K1, M

PAL, SECAM, NTSC3.58/4.43MHz

Channels and frequencies

VHF low channel (VL) =46.25 to 168.25 MHz

VHF high channel (VH) =175.25 to 463.25 MHz

UHF channel (U)

=471.25 to 863.25 MHz

• Receives cable channels in mid band (X to Z+2, S1 to S10), super band (S11

to S20) and hyper band (S21 to S41).

Sound-multiplex systems

Teletext systems

A2 (B/G), NICAM (B/G, I, D/K) system

FLOF(Fastext), WST(World Standard Text)

Languages displayed by

teletext

Please see the table in the description “TELETEXT LANGUAGE” on page 34.

Power requirements

Audio output

AC 110 to 240V, 50/60Hz

Rated Power output: 15W + 15W [HV-Z34L1], 10W + 10W + 18W [HV-Z29V1]

VIDEO-1 terminal

RCA connector × 3, S-VIDEO connector × 1

• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.

VIDEO-2 (COMPONENT)

VIDEO-3 (COMPONENT)

RCA connector × 6

• Video input, Componet video (Y, Cb/Pb, Cr/Pr) input and Audio L/R inputs are

available.

• 625p, 525p and 1125i signals are available.

RCA connector × 6

• Video input, Componet video (Y, Cb/Pb, Cr/Pr) input and Audio L/R inputs are

available.

• 625p, 525p and 1125i signals are available.

VIDEO-4 terminal

OUTPUT terminal

RCA connector × 3, S-VIDEO connector × 1

• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.

RCA connector × 3

• Video output and Audio L/R outputs are available.

Headphone jack

Accessories

Stereo mini-jack (3.5 mm in diameter)

Remote control unit × 1 (RM-C1850)

AA/R6 dry cell battery × 2

Woofer unit × 1 [HV-Z29V1 only]

Speakers

HV-Z34L1: 12cm round × 2, 3.5cm round × 2

HV-Z29V1: (13cm × 6.5cm) oval × 2, 13cm round × 1(Woofer unit)

Design and specifications subject to change without notice.

Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any commercial or

demonstration purpose in public places (cafes, hotels, etc.) without the consent of the owners of copyright of

the original picture sources, as this constitutes an infringement of copyright.

VICTOR COMPANY OF JAPAN, LIMITED

Kenmore ELITE 3231 User Manual
Keyspan Cordless VoIP Phone User Manual
KitchenAid KGCC766 User Manual
LG Electronics LG Life Good Computer Monitor E2351T User Manual
Magnavox 29MT4515 User Manual
Magnavox MWC20D6 User Manual
Nortel Networks Nortel IP Phone 1210 User Manual
Philips 28PT7138 User Manual
Philips 29PT6807 User Manual
Philips MCD715 User Manual