JVC AV32P10EK AV32L5EK AV32P10EI AV32L5EI User Manual

Specifications

Model

AV32L5EK* (UK model)

AV32L5EI* (Ireland model)

Item

Broadcasting systems

Colour systems

CCIR I

PAL

•

The EXT terminals also support the NTSC 3.58/4.43 MHz system.

COLOUR TELEVISION

Channels and frequencies

E21-E69

IR A-J, E2-E12, E21-E69, S1-S41, X, Y, Z,

Z+1, Z+2, ITALY A-H, ITALY H+1, ITALY H+2

Sound-multiplex systems

Teletext systems

Power requirements

Power consumption

Picture tube size

Audio output

NICAM (I) system

Contents

FLOF (Fastext), WST (World Standard Text)

220 - 240 V AC, 50 Hz

Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Setting up your TV . . . . . . . . . . . . . . . . . . . . . . . . . . .4

T-V LINK functions . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Using your TV–the basics. . . . . . . . . . . . . . . . . . . . . .8

Remote control buttons and functions . . . . . . . . . . . . .11

Using the TV’s menus. . . . . . . . . . . . . . . . . . . . . . . .17

Picture setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Picture features. . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Sound setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

DIGITAL SURROUND (Only AV32P10EK and AV32P10EI) . .23

EXT SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

FEATURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

INSTALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

DEMO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Other menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Further preparation. . . . . . . . . . . . . . . . . . . . . . . . . .37

TV buttons and parts . . . . . . . . . . . . . . . . . . . . . . . .41

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

AV32P10EK

Maximum: 189 W, Average: 140 W, Standby: 2.8 W

Viewable area 76 cm (measured diagonally)

Rated Power output: 7.5 W + 7.5 W

(20 cm × 4 cm) oval × 2

AV32L5EK

(UK model)

Speakers

EXT-1 terminal

Euroconnector (21-pin, SCART)

•

Video input, Audio L/R inputs and RGB inputs are available.

TV broadcast outputs (Video and Audio L/R) are available.

EXT-2 terminal

Euroconnector (21-pin, SCART)

•

Video input, S-VIDEO (Y/C) input, Audio L/R inputs and RGB inputs are available.

Video and Audio L/R outputs are available.

T-V LINK functions are available.

AV32P10EI

EXT-3 terminal

EXT-4 terminal

Euroconnector (21-pin, SCART)

Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.

•

AV32L5EI

RCA connectors × 3

S-VIDEO connector × 1

(Ireland model)

•

Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.

AUDIO OUT terminal

RCA connectors × 2

•

Variable audio L/R outputs are available.

Variable out 0-1 Vrms, low impedance

Headphone jack

Dimensions (W × H × D)

Weight

Stereo mini-jack (3.5 mm in diameter)

901 mm × 556 mm × 557mm

53.9 kg

Accessories

Remote control unit × 1 (RM-C56)

AAA/R03 dry cell battery × 2

* A basic model number. The actual model number may have characters added (such as “S” denoting silver) indicating the colour

of the TV set.

We may change the design and specifications without notice.

Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any commercial or demonstration pur-

pose in public places (cafes, hotels, etc.) without the consent of the owners of copyright of the original picture sources, as this

would be an infringement of copyright.

INSTRUCTIONS

VICTOR COMPANY OF JAPAN, LIMITED

LCT0909-001B-U

0106-T-CR-JMUK

Thank you for buying this

colour television.

To make sure you fully understand how to use your new TV, please read this manual thoroughly before

you begin.

Safety precautions

^IWarning

To prevent fire or shock hazard, do not expose

this appliance to rain or moisture.

Warning

DO NOT cut off the mains plug from this

equipment. If the plug fitted is not suitable for the

power points in your home or the cable is too short

to reach a power point, then obtain an appropriate

safety approved extension lead or adaptor or

consult your dealer.

Caution

To ensure personal safety, observe the following

rules regarding the use of this unit.

If nonetheless the mains plug is cut off, remove

the fuse and dispose of the plug immediately, to

avoid a possible shock hazard by inadvertent

connection to the mains supply.

1 Operate only from the power source specified

(AC 220 – 240 V, 50 Hz) on the unit.

2 Avoid damaging the mains plug and power

cord.

If a new mains plug has to be fitted, then follow the

instruction given below:

3 Avoid improper installation and never position

the unit where good ventilation is unattainable.

When installing this television, distance

recommendations must be maintained

between the floor and wall, as well as

installation in a tightly enclosed area or piece of

furniture.

Important

Do not make any connection to the larger terminal

which is marked with the letter E or by the safety

earth symbol or coloured green or green-and-

yellow.

Please adhere to the minimum distance

guidelines shown for safe operation.

The wires in the mains lead on this product are

coloured in accordance with the following code:

Blue: Neutral

15 cm

Brown: Live

As these colours may not correspond with the

coloured marking identifying the terminals in your

plug proceed as follows:

10 cm

15 cm

4 Do not allow objects or liquid into the cabinet

openings.

The wire which is coloured blue must be

connected to the terminal which is marked with the

letter N or coloured black.

5 In the event of a fault, unplug the TV and call a

service technician. Do not attempt to repair it

yourself or remove the rear cover.

6 The surface of the TV screen is easily

damaged. Be very careful with it when handling

the TV.

The wire which is coloured brown must be

connected to the terminal which is marked with the

letter L or coloured red.

Should the TV screen become soiled, wipe it

with a soft dry cloth. Never rub it forcefully.

Never use any cleaner or detergent on it.

When replacing the fuse only a correctly rated

approved type should be used and be sure to

re-fit the fuse cover.

7 The main power button on the TV does not fully

isolate the TV from the mains supply. If you are

not going to use this TV for a long period of

time, be sure to disconnect the mains plug from

the mains outlet.

If in doubt — consult a competent

electrician.

How to replace the fuse

Open the fuse

compartment with a blade

screwdriver, and replace

the fuse.

Fuse

Guidelines for safe operation

This equipment has been designed and manufactured to comply with international safety standards.

However, as with any electrical appliance, care must be taken to ensure optimal results and operational

safety.

• Before attempting to use this equipment, read the operating instructions thoroughly.

• Ensure that all electrical connections (including the mains plug, extension leads, etc.) have been made

in accordance with the manufacturer’s instructions.

• If ever in doubt about the installation, operation or safety of this equipment, consult your dealer.

• Handle all glass panels or covers with care.

• Never operate this equipment if it appears damaged or operates abnormally. Turn the power off,

disconnect the main power plug and consult your dealer.

• Never remove any affixed panels or covers. Doing so may result in electrical shock.

• Never leave this equipment operating unattended unless otherwise specifically stated that it is designed

to do so or in standby mode. Only use the designated power switch to turn off the power and ensure

that all potential users are instructed how to do so. Make special arrangements for infirm or handicapped

persons.

• Never listen to headphones at high volume. Doing so may damage your hearing.

• Never obstruct the ventilation of this equipment. Doing so may cause overheating and result in a

malfunction or damage.

• Never use makeshift stands or attempt to affix legs with wood screws. When using a manufacturer’s

approved stand or legs, use only the fixtures provided and follow the installation instructions.

• Never allow this equipment to be exposed to rain or moisture.

• Never allow anyone, especially children, to insert anything into an opening in the case. Doing so may

result in a fatal electrical shock.

• Never guess or take chances with electrical equipment of any kind. It is better to be safe than sorry.

Setting up your TV

I Connecting the aerial and video cassette recorder (VCR)

If you are connecting a VCR, follow

Aerial

→

C in the diagram opposite.

If you are not connecting a VCR, follow 1.

75-ohm

coaxial

cable

• For more details, see the manuals that came with the

equipment you want to connect.

• The connecting cables are not provided.

Back of the TV

COAXIAL

DIGITAL

• You can watch a video using the VCR without doing C.

For details, see your VCR instruction manual.

AUDIO IN

OPTICAL

SUB

WOOFER

AUDIO OUT

• To connect more equipment, please see “Further

preparation” on page 37.

EXT-2

EXT-3

•

To connect additional audio equipment, see “Using

additional audio equipment” on page 39.

EXT-1

SURROUND

REAR

• To connect other equipment (such as a DVD player) with

a digital output terminal for Dolby Digital, see “Listening

to Dolby Digital audio (Only AV32P10EK and

AV32P10EI)” on page 38.

• If you connect a decoder to a T-V LINK compatible VCR,

set the DECODER (EXT-2) function to ON. For details, see

“Using the DECODER (EXT-2) function” on page 35.

Otherwise, you will not be able to watch scrambled

channels.

75-ohm

21-pin SCART

cable

coaxial

cable

To aerial

input

VCR

To use the T-V LINK functions, you must have a T-V LINK

compatible VCR connected by a SCART cable C to the EXT-

2 terminal on the TV. For details about T-V LINK functions,

see “T-V LINK functions” on page 7.

To aerial

output

AV IN/OUT

terminal

I Connecting the power cord to the mains outlet

Caution:

• Use only the power source specified on the unit

(AC 220 – 240 V, 50 Hz).

I Putting batteries into the remote control

Use two AAA/R03 dry cell batteries.

Insert the batteries holding the - end, making sure the + and

- terminals are correctly lined up.

To open the battery compartment, slide the door downwards

and lift off. Replace the door by sliding it upwards until it

fastens into place.

• Follow the warnings printed on the batteries.

• Battery life is about six months to one year, depending on

how much you use the remote control.

• If the remote control does not work properly, fit new

batteries.

• The batteries we supply are only for setting up and

testing your TV. Please replace them as soon as you

need to.

• Always use good-quality batteries.

Setting up your TV

I Initial settings

When the TV is first turned on, it goes into the initial setting

mode, and you will see the JVC logo. Follow the instructions

on the screen to make the initial settings.

Press the main power button on the TV

The power lamp lights red (for power on), then green (for

TV on) and the JVC logo appears.

main power

button

power lamp

D0001-EK

• If the power lamp stays red and does not change to

green:

your TV is in the standby mode. Press the

(standby) button on the remote control to turn your

TV on.

main power

button

power lamp

• If the JVC logo does not appear this is because your

TV has already been turned on for the first time:

use the “LANGUAGE” and “AUTO PROGRAM”

functions to make the initial settings. For details, see

“INSTALL” on page 30.

2 ^{Press the}

button

The LANGUAGE menu appears.

LANGUAGE

yellow button

blue button

BACK

PIP

D0002(E)-EK

3 ^{Press the}⁵^and⁶^{buttons to}

choose ENGLISH

The on-screen display will then be in English.

Setting up your TV

4 Press the

button to start the AUTO

PROGRAM function

8 Now, the initial settings are complete,

and you can watch the TV

The AUTO PROGRAM menu appears and the TV

channels you receive are automatically stored in the

programme numbers list (PR).

Note:

• For UK model (AV32P10EK/AV32L5EK):

BBC1, BBC2, ITV, Channel 4 and Channel 5 are

automatically set to the programme numbers PR1 to

PR5.

AUTO PROGRAM

EDIT

CH 10

20%

BBC1

BBC2

ITV

CH4

CH5

If the TV doesn't receive one of these TV channels,

that programme number (PR) will not be set.

Programme number PR6 is not normally set.

• For Ireland model (AV32P10EI/AV32L5EI):

If your TV can detect the TV channel name from the

TV channel broadcast signal, the TV channel name

is assigned to the programme number (PR) to which

the TV channel has been set.

However, which TV channels are set to which

programme numbers (PR) will depend on the area in

which you live.

• If a TV channel you want to view is not set to a

programme number (PR), you can set it using the

MANUAL function. For details, see “EDIT/MANUAL”

on page 31.

BACK

MOVE

INSERT

DELETE

MANUAL

D0004-EK

If “ACI START/ACI SKIP” appears in the AUTO

PROGRAM menu:

You can use the ACI (Automatic Channel Installation)

function to decode the ACI data and complete the

registration of all the TV channels quickly. For details of

the ACI function and how to use it, refer to “Using the

ACI function” on page 35.

If you don’t want to use the ACI function, press the

• The AUTO PROGRAM function does not set the

programme number PR 0 (AV) for your video

cassette recorder. You will need to set this using the

MANUAL function.

button to choose ACI SKIP and then press

To cancel the AUTO PROGRAM function:

Press the button.

• In some areas you may get TV reception from more

than one transmitter, for example different ITV

regions. In this case each TV channel could be set

twice. If this happens, the first set of channels will

have the stronger signal. If you want to delete the

second set of channels, you will have to do it

manually (see page 33).

5 ^Afterthe TV channels have been

registered in the programme numbers

list (PR), the EDIT menu appears

If you want to, you can now edit the programme numbers

(PR) using the EDIT/MANUAL function. For details, see

“EDIT/MANUAL” on page 31.

If you do not want to edit programme numbers (PR), go

to the next step.

For users in the UK:

If you have any problems setting up your

new TV, please call the

6 Press the

button to display the T-V

Helpline on 0870 330 5000.

LINK menu

For users in the Republic of Ireland:

If you have any problems setting up your

new TV, please contact your local

dealer.

T-V LINK

DOWNLOAD TV

VCR

BACK

EXIT

D0005-EK

7 Follow the T-V LINK menu according to

the type of VCR you have connected to

the EXT-2 terminal

If you do not have a T-V LINK compatible VCR

connected:

Press the

The T-V LINK menu disappears.

button to leave the T-V LINK menu.

If you have a T-V LINK compatible VCR

connected:

Follow the operating procedure “Downloading data to a

VCR” on page 35 to transmit the programme number

(PR) data.

T-V LINK functions

When you have a T-V LINK compatible VCR connected to the

EXT-2 Terminal on the TV, it is easier to set up the VCR and

to view videos. T-V LINK uses the following features:

I TV auto power on/VCR

image view

When the VCR starts playing, the TV automatically turns on

and the images from the EXT-2 terminal appear on the

screen.

I Pre-set download

The VCR will automatically download the registered data on

the TV channels from the TV. This means you do not need to

set up the program channels on your VCR manually.

The preset download function automatically begins when the

initial setting is complete or whenever you carry out the AUTO

PROGRAM or EDIT/MANUAL functions.

When the VCR menu is operated, the TV automatically turns

on and the images from the EXT-2 terminal appear on the

screen.

This function does not happen if your TV’s main power is

turned off. Set your TV’s main power to on (standby mode).

You can also carry out this function using your VCR controls.

Note:

When “FEATURE NOT AVAILABLE” is displayed:

• A “T-V LINK compatible VCR” means a JVC video

cassette recorder with the T-V LINK logo, or with one of

the following logos. However, these VCRs may support

some or all of the features described earlier. For details,

see your VCR instruction manual.

If “FEATURE NOT AVAILABLE” is displayed, the download

was not performed correctly. Before trying to download again,

check that:

• the VCR power is turned on

“Q-LINK” (a trademark of Panasonic Corporation)

“Data Logic” (a trademark of Metz Corporation)

“Easy Link” (a trademark of Phillips Corporation)

“Megalogic” (a trademark of Grundig Corporation)

“SMARTLINK” (a trademark of Sony Corporation)

• the VCR is T-V LINK compatible

• the VCR is connected to the EXT-2 terminal

• the SCART cable is fully wired

I Direct Rec

“What You See Is What You Record”

You can easily record to VCR the images that you are

watching on the TV.

For details, read the manual for your VCR.

Use your VCR controls. “VCR IS RECORDING” is displayed.

In the following situations, the VCR will stop recording if

the TV is turned off, if the TV channel or input is changed,

or if the menu is displayed on the TV:

• when recording images from an external device connected

to the TV (for example a camcorder)

• when recording a TV channel after it has been unscrambled

on a decoder

• when recording a TV channel by using the TV’s output

because the VCR’s own tuner cannot properly receive that

channel

• You cannot carry out Direct Rec using your TV’s control.

• Generally, the VCR cannot record a TV channel that it

cannot receive properly on its own tuner, even if you can

view that TV channel on the TV. However, some VCRs

can record a TV channel by using the TV’s output if that

channel can be viewed on the TV. For details, see your

VCR instruction manual.

Using your TV–the basics

I Turn the main power on

Press the main power button on the TV

The power lamp lights red and your TV is in the standby mode.

If the power lamp lights green, the TV is already on.

To turn the main power off:

Press the main power button again.

The power lamp goes off.

power lamp

main power

button

The main power button on the TV does not fully cut the TV off

from the mains supply. If you are not going to use this TV for a

long time, be sure to pull the mains plug out of the mains outlet.

main power

button

power lamp

I Turn the TV on from standby mode

Press the

button, the

buttons

(standby) button, the

buttons or the number

The power lamp goes from red to green and your TV will be

turned on.

To turn the TV off:

number

buttons

Press the

(standby) button again.

The power lamp changes from green to red and the TV goes

into standby mode.

PIP

I Choose a TV channel

Choose the programme number (PR) that the TV channel has

been set to.

Use the 6buttons:

Press the 6 buttons to choose the programme number

(PR) you want.

Use the number buttons:

Enter the programme number (PR) of the channel using the

number buttons.

Example

• PR12 → press 1 and 2.

• PR6 → press 6.

Use the PR LIST:

1 Press the h (information) button to

display the PR LIST

PR LIST

BBC1

BBC2

ITV

CH4

CH5

-10

+10

D0006-EK

Using your TV–the basics

Use the 6buttons:

2 Press the 5and 6buttons to choose

Press the

buttons to choose an EXT terminal

a programme number (PR). Then press the

button

Use the PR LIST:

• For programme numbers (PR) where you have the CHILD

1 Press the

(information) button to

display the PR LIST

LOCK function set, the (CHILD LOCK) mark appears

next to the programme number (PR) in the PR LIST.

• You cannot use the 6 buttons to choose a programme

number (PR) which has the CHILD LOCK set.

2 Press the 5and 6buttons to choose

• Even if you try to choose a programme number (PR) with

an EXT terminal. Then press the

button

the CHILD LOCK set, the (CHILD LOCK) mark will

• The EXT terminals are listed after programme number PR

99.

appear, and you cannot watch the TV channel. To watch

the TV channel, see “CHILD LOCK” on page 28.

• You can choose two types of video input signal:

S-VIDEO (Y/C signal) and regular video (composite

signal). For details, see “S-IN (S-VIDEO input)” on

page 26.

• When listening to Dolby Digital audio, see “Listening to

Dolby Digital audio (Only AV32P10EK and AV32P10EI)”

on page 38.

• If you do not have a clear picture or no colour appears,

change the colour system manually. See “COLOUR

SYSTEM” on page 20.

• If you choose an EXT terminal with no input signal, the

EXT terminal number becomes fixed on the screen.

• This TV set can automatically change over the input

according to a special signal from an external device.

(The EXT-4 terminal does not support it.)

• If the picture is tilted, correct it. See “PICTURE TILT” on

page 20.

I Changing the volume

Press the

volume.

buttons to change the

The volume indicator appears, and the volume changes, as

you press the qbuttons.

To listen to the sound using headphones:

See “HEADPHONE” on page 22.

I Watching images from

To use the programme number PR 0 (AV):

external equipment

When the TV and VCR are connected only by the aerial cable,

choosing the programme number PR 0 (AV) allows you to

view images from the VCR. Set the VCR RF channel to

programme number PR 0 (AV) manually. For details, see

“EDIT/MANUAL” on page 31.

Choose the EXT terminal that the external equipment has

been connected to.

Use the

button:

Press the

button to choose an EXT terminal.

Pressing the

button changes the choice as follows:

Pressing the

button changes the choice as follows:

TV mode

EXT modes

TV mode

Programme

PR 0

EXT-1

EXT-4

EXT-2

EXT-3

Programme

numbers

PR 1 to PR 99

numbers

EXT-1

EXT-4

EXT-2

EXT-3

PR 1 to PR 99

• The VCR sends its playback image along the aerial cable

as an RF (radio frequency) signal.

• Also see your VCR instruction manual.

To return to a TV channel:

Press the

buttons.

button, the

buttons or the number

Using your TV–the basics

I Using the buttons on the TV

1 Press the P p buttons to turn the

Behind the Cover

TV on from standby mode

Press the P

buttons to choose a

programme number (PR) or an EXT

terminal

3 ^{Press the}r (volume) button and the

q buttons to change the volume

1 Press the r(volume) button

The volume level indicator appears

2 Press the qbuttons while the volume

level indicator is on screen

• The buttons on the TV cannot be used to change the

volume of the headphones.

Side of the TV

EXT-2

EXT-3

EXT-1

Remote control buttons and functions

1 Muting button

You can turn the sound off instantly.

Press the

sound. Pressing the

restores the previous volume level

(muting) button to turn off the

(muting) button again

2 Number buttons

You can choose a programme number (PR) by

entering the programme number

Example:

→

• PR12

press 1 and 2.

PIP

→

• PR6

press 6.

You can also press the

an EXT terminal.

button repeatedly to choose

3 ZOOM button

You can change the screen size by changing the picture

aspect ratio. The normal aspect ratio is 4:3 (width:height).

Choose the ideal one from the following ZOOM modes.

AUTO:

For any picture format except normal picture (4:3 aspect

ratio), the picture will be automatically displayed in the ideal

screen size.

For normal picture (4:3 Aspect Ratio), you can choose a

ZOOM mode from the 4:3 AUTO ASPECT menu. For details,

see “4:3 AUTO ASPECT” on page 20.

• AUTO may not work properly with poor signal quality. In

this case, choose the best ZOOM mode manually.

• This TV supports WSS (wide-screen signals). When

broadcasts with WSS are received with the ZOOM mode

set at AUTO, the most suitable ZOOM mode is

automatically chosen according to the WSS received.

REGULAR:

Use to view a normal picture (4:3 aspect ratio) as this is its

original shape.

PANORAMIC:

How to open the cover

This stretches the left and right sides of a normal picture (4:3

aspect ratio) to fill the screen, without making the picture

appear unnatural.

• The top and bottom of the picture are slightly cut off.

Remote control buttons and functions

14:9 ZOOM:

This zooms up the wide picture (14:9 aspect ratio) to the

upper and lower limits of the screen.

Adjusting the visible area of the

picture

If subtitles or the top (or bottom) of the picture are cut off, you

can adjust the visible area of the picture manually.

1 Press the c button

The ZOOM menu appears.

16:9 ZOOM:

This zooms up the wide picture (16:9 aspect ratio) to the full

screen.

2 Press the

button to display the ZOOM

mode indicator

The indicator appears.

16 : 9 ZOOM

D0010-EK

3 While it is displayed, press the

16:9 ZOOM SUBTITLE:

buttons to change the height of the picture

This zooms up the wide picture (16:9 aspect ratio) with

subtitles to the full screen.

• You cannot adjust the visible area in REGULAR or

FULL mode.

4 3D Button (Only AV32P10EK and

AV32P10EI)

You can turn the 3D-PHONIC function on or off by one-touch

operation.

FULL:

This uniformly stretches the left and right sides of a normal

picture (4:3 aspect ratio) to fill the wide TV screen.

Press the 3D button

Pressing the 3D button changes the function as follows:

3D-PHONIC

• For 16:9 aspect ratio pictures that have been squeezed

into a normal picture (4:3 aspect ratio), use the FULL

mode to restore the picture to its original shape.

SURROUND OFF

Choose the ZOOM mode

Previous surround function

1 Press the c button to display the

ZOOM menu

D0043-EK

ZOOM

• For details, see “3D-PHONIC” on page 23.

• If another surround function is activated before you press

the 3D button, you can return to that surround function.

• The 3D button does not work while the headphones are

connected to the TV.

AUTO

REGULAR

PANORAMIC

14:9 ZOOM

16:9 ZOOM

16:9 ZOOM SUBTITLE

FULL

BACK

D0009-EK

2 Press the

buttons to choose a ZOOM

button

mode. Then press the

The picture expands and the chosen ZOOM mode is

displayed in about 5 seconds.

• The ZOOM mode may be automatically changed by

the control signal from an external device. When you

want to return to the previous ZOOM mode, choose

the ZOOM mode again.

Remote control buttons and functions

5 Information button

9 Colour buttons

You can display the PR LIST or the current time on the

screen.

The colour buttons are used for the teletext operations or the

menu operations. For details, see “$ Teletext control buttons

and VCR P DVD switch” on page 15 or “Using the TV’s

menus” on page 17.

Press the

Pressing the

display as follows:

(information) button

(information) button changes the

0 OK button

The

button is used to operate menus. For details, see

PR LIST

“Using the TV’s menus” on page 17.

Buttons

12 : 00

BBC1

BBC2

ITV

CH4

CH5

You can choose a programme number (PR) or an EXT

terminal.

Press the

buttons to choose a

No display

Programme number (PR) or an EXT terminal.

The

buttons will also operate menus.

For details, see “Using the TV’s menus” on page 17.

-10

+10

D0011-EK

= VCR/DVD control buttons and

• You can choose programme numbers (PR) or EXT

terminals with the PR LIST. For details, see “Use the PR

LIST:” on page 8.

VCR P DVD switch

These buttons will operate a JVC brand VCR or DVD player.

Pressing a button that looks the same as the device’s original

remote control button has the same effect as the original

remote control.

• This TV uses teletext data to set the time. If the TV has not

received a TV channel that has teletext programmes

since it was turned on, the time display is blank. To see

the time, choose

TV channel that has teletext

1 Set the VCR P DVD switch to the VCR or

programmes. The time will still be displayed as long as

you do not turn off the TV, even if you choose other TV

channels.

DVD position.

VCR:

• When watching videos, the incorrect time is sometimes

displayed.

When you are using a VCR, set the switch to the VCR

position.

• The

(information) button will also operate menus. For

details, see “Using the TV’s menus” on page 17.

DVD:

When you are using a DVD player, set the switch to the

DVD position.

6 TV button

You can return to a TV channel instantly.

2 Press the VCR/DVD control button to

control your VCR or DVD player

Press the

button.

The TV returns to the TV mode and a TV channel appears.

• If your device is not made by JVC, these buttons will

not work.

• The

button will also operate menus. For details, see

“Using the TV’s menus” on page 17.

• Even if your device is made by JVC, some of these

buttons may not work, depending on the device you

are using.

7 5 Buttons

You can adjust the volume.

• You can use the

buttons to choose a TV channel

the VCR will receive, or choose the chapter the DVD

player plays back.

Press the 5buttons to adjust the sound.

• The 5buttons will also operate menus. For details, see

“Using the TV’s menus” on page 17.

• Some models of DVD player use the

buttons for

both operating the fast forward/backward functions

and for choosing the chapter. In this case, the 1/

¡ buttons do not work.

8 Standby button

Press the

on or off.

(standby) button to turn the TV

When the TV is turned on, the power lamp changes from red

to green.

Remote control buttons and functions

• When the PIP button is pressed while watching a

picture from an EXT terminal, the picture from a TV

channel or the picture from another EXT terminal is

displayed as the sub-picture.

~ FREEZE button

You can view the current programme as a still picture.

Press the SUB-P

buttons @ to change the

1 Press the FREEZE button

sub-picture to the picture from another TV channel

or another EXT terminal.

The still picture of the current picture will appear.

• The main-picture and sub-picture must be different.

• If the main-picture signal is poor, the quality of the

sub-picture may also be poor.

current

programme

still

picture

D0049-EK

• If the pictures have different standards, the top and

bottom of one of them may be missing.

To cancel the FREEZE function:

Press the FREEZE button again.

• The sub-picture will disappear if the TV receives a

control signal from the external device.

• The ZOOM function does not work in the

twin-picture mode.

• The FREEZE function does not work while a

sub-picture is displayed.

• The STEREO / I • II function does not work in the EXT

modes even if you are viewing a TV programme in

the sub-picture.

• The still picture cannot be output from the TV.

!@# PIP control buttons

You can view two pictures (Main-picture and sub-picture).

You can view a TV programme received by the TV and a

video programme from an external device at the same time.

• The BLUE BACK function does not work in the twin

picture mode or the picture in picture mode.

• The sub-picture cannot be output from the TV.

Listening to the sound of the sub-picture:

You can listen to the sound of the sub-picture with the

headphones while listening to the sound of the

main-picture from the TV speakers.

• If a device which can receive broadcast programmes

(such as a satellite tuner or VCR) is connected to the TV's

EXT terminal, both the broadcast programme received

by that device and the broadcast programme received

by the TV can be viewed at the same time.

• With just the TV, two broadcast programmes cannot be

viewed at the same time.

For details, see “HEADPHONE” on page 22.

Changing the position of the sub-picture:

You can choose one of four positions.

For details, see “PIP POSITION” on page 20.

1 Press the PIP button !

Swapping the main-picture and sub-picture:

Press the SWAP button # .

The main-picture and sub-picture will be swapped.

Pressing the PIP button changes the PIP mode as

follows:

Twin pictures mode

Main

Sub

-picture

Picture in picture mode

D0051-EK

Sub

Main

-picture

Cancel the PIP function

Main

-picture

D0050-EK

• When the PIP button is pressed while watching a TV

programme, the picture from an EXT terminal is

displayed as the sub-picture.

Press the SUB-P

buttons @ to change the

sub-picture to the picture from another EXT terminal.

Remote control buttons and functions

I $ Teletext control buttons and VCR P DVD switch

4 Choose a teletext page by pressing the

buttons, number buttons or colour

PIP

buttons

To return to the TV mode:

Press the

button or

(Text) button.

• If you have trouble receiving teletext broadcasts,

contact your local dealer or the teletext station.

• The ZOOM function will not work in the text mode or

TV and text mode.

• You cannot operate menus when viewing a teletext

programme.

• Teletext programmes cannot be viewed while a sub-

picture is displayed.

Using the List Mode

You can store the numbers of your favourite teletext pages in

memory and call them up quickly using the colour buttons.

To store the page numbers:

1 Press the M button to go into the List

mode

The page numbers you have stored are displayed at the

bottom of the screen.

2 Press a colour button to choose a

position. Then press the number buttons

to enter the page number

Basic operation

You can view two types of teletext broadcasts on the TV:

FLOF (Fastext) and WST (World Standard Text).

PIP

1 Choose a TV channel with a teletext

broadcast

PIP

2 Set the VCR PDVD switch to the

(Text)

3 Press and hold down the

button

position

The four page numbers blink white to show that they are

stored in memory.

To call up a stored page:

3 Press the g (Text) button to display the

1 Press the M button to enter the List

teletext

mode

Pressing the g (Text) button changes the mode as follows:

2 Press a colour button having a stored page

TEXT

---

PIP

To leave the List mode:

Press the M button again.

TV and text mode

TV mode

TEXT

---

D0012-EK

Text mode

Remote control buttons and functions

Hold

Size

You can hold a teletext page on the screen for as long as you

want, even while several other teletext pages are being

received.

You can double the height of the teletext display.

Press the R button.

Press the N button

Hold indication

To cancel the Hold function:

Press the N button again.

Sub-page

Some teletext pages include sub-pages that are automatically

displayed.

Index

You can return to the index page instantly.

You can hold any sub-page, or view it at any time.

Press the t button

1 Press the O button to operate the

FLOF (Fastext)/WST (World Standard Text):

Returns to page 100 or a previously specified page.

sub-page function

Sub-page numbers are displayed at the left of the

screen.

List mode:

Returns to the page number displayed in the lower left area of

the screen.

Colour*

Yellow

Meaning of sub-page number

Currently being displayed.

Can be displayed.

Cancel

White

You can search for a teletext page while watching TV.

Blue or Red

Cannot be displayed and it is not sent.

1 Press the number button to enter a page

number, or press a colour button

The TV searches for a teletext page.

* Background colour of the sub-page number.

2 Press the 6buttons to choose a subpage

number.

2 Press the S button.

To cancel the sub-page function:

The TV programme appears. When the TV finds the

teletext page, its page number appears in the upper left

of the screen.

Press the O button again.

Reveal

3 Press the S button to return to a

teletext page when the page number is on

the screen

Some teletext pages include hidden text (such as the

answers to a quiz).

You can display the hidden text.

Note:

Each time you press the Q button, text

• The TV mode cannot be resumed by pressing the

is hidden or revealed

button. To return to the TV mode press

Using the TV’s menus

This TV has a number of functions you can operate using

menus. To use all your TV’s functions fully, you need to

understand how to use the basic menus.

3 ^{Follow the menus according to the}

function you want to use

• For more details, see the descriptions of each menu

and its functions on the following pages.

1 Press the

button to display the

MENU (main menu)

• The display appearing at the bottom of a menu

shows you a button on the remote control that you

can use when you operate a chosen function.

The MENU (main menu) appears. In it, the titles of the

menus are displayed.

4 ^{Press the}

button to complete the

setting

The menu disappears.

PICTURE SETTING

PICTURE FEATURES

SOUND SETTING

EXT SETTING

FEATURES

INSTALL

To return to the previous menu:

Press the

(information) button.

To exit a menu instantly:

DIGITAL SURROUND

DEMO

Press the

button.

BACK

• When watching the television with the NTSC system,

the menus are displayed at about half of their normal

vertical size.

D0052-EK

• The title of the DIGITAL SURROUND menu is not

displayed while the headphones are connected to

the TV.

PICTURE SETTING

PICTURE FEATURES

SOUND SETTING

EXT SETTING

FEATURES

INSTALL

DEMO

BACK

D0013-EK

• AV32L5EK and AV32L5EI do not have DIGITAL

SURROUND menu.

2 ^{Press the}

buttons to choose a

menu title, and press the

button

The menu appears.

PICTURE SETTING

TINT

NORMAL

CONTRAST

BRIGHT

SHARP

COLOUR

HUE

ECO MODE

OFF

BACK

RESET

D0014-EK

Picture setting

I Picture adjustment

PICTURE SETTING

You can change the picture settings of each TINT mode as

you like.

TINT

NORMAL

CONTRAST

BRIGHT

SHARP

COLOUR

HUE

ECO MODE

The picture settings changed are stored in the TINT mode.

OFF

1 Press the 6 buttons to choose an item.

BACK

RESET

2 Press the 5 buttons to change the

D0014-EK

setting.

To display the PICTURE SETTING menu:

Item

Lower

Higher

CONTRAST

(picture contrast)

1 Press the

button to display the MENU

(main menu)

Darker

Softer

Brighter

Sharper

Deeper

BRIGHT

(picture brightness)

2 Press the 6 buttons to choose PICTURE

SETTING, and press the button

SHARP

(picture sharpness)

Lighter

Reddish

COLOUR

(picture colour)

I TINT

You can select one of three TINT modes (three kinds of

picture settings) to adjust the picture settings automatically.

Greenish

HUE

(picture hue)

1 Press the 6 buttons to choose TINT

•

You can change the HUE setting (picture hue) only

when the colour system is NTSC 3.58 or NTSC 4.43.

(See “Specifications” on page 43 and the back cover.)

2 Press the 5 buttons to choose a mode

To return to the default settings in each TINT

mode:

Press the blue button.

COOL:

A cool white colour base with a boost in the colour and

contrast levels that creates a more vivid picture.

This returns the picture settings in the TINT mode you

have chosen to the default settings, and stores them in

the TINT mode.

WARM:

A warm orange/red colour base that creates the

appropriate colour and contrast levels for watching films.

3 Press the

settings

button to complete the

NORMAL:

A normal white colour base with normal colour and

contrast levels.

The menu disappears.

3 Press the

setting

button to complete the

I ECO MODE

When you set the ECO MODE function to ON, the screen

contrast is automatically adjusted to a setting suitable for the

brightness of your room. This reduces eye strain for you and

the amount of power the TV uses.

The menu disappears.

1 Press the 6 buttons to choose ECO

MODE

2 Press the 5 buttons to choose ON

To cancel the ECO MODE function:

Press the 5 buttons to choose OFF.

3 Press the

setting

button to complete the

The menu disappears.

Picture features

I DigiPure Pro

PICTURE FEATURES

The DigiPure Pro function uses the latest in digital technology

to give you a natural-looking picture. The DigiPure Pro

function includes the following two functions.

DIGITAL VNR

AUTO

DigiPure Pro

COLOUR SYSTEM

4:3 AUTO ASPECT

PICTIRE TILT

PIP POSITION

DigiPure function:

BACK

This function helps to create a natural-looking picture by

eliminating unnecessary edges from high-contrast and crisp

images. For images with low-contrast, edges are added to

produce a sharper, more detailed picture.

D0015-EK

To display the PICTURE FEATURES menu:

You can choose from the three DigiPure function settings of

AUTO, MIN and MAX.

1 Press the

button to display MENU

• If you set the DigiPure effect too high on a low-quality

picture that contains a lot of noise, this may actually make

the noise worse. We recommend you use the AUTO

setting if you can.

(main menu)

2 Press the6buttons to choose PICTURE

FEATURES, and press the a button

Picture motion compensation function:

This function displays fast-moving pictures (for example, the

players or ball in a football game) more smoothly and

naturally on the screen.

I DIGITAL VNR

The DIGITAL VNR function cuts down the amount of noise

(graininess) in the original picture.

You can choose from the three DIGITAL VNR function

settings of AUTO, MIN and MAX.

• The effect level of the picture motion compensation

function cannot be changed. The effect level is the same

no matter which of the AUTO, MIN or MAX settings is

used.

• If you set the DIGITAL VNR effect too high it can make the

picture less sharp. We recommend you use the AUTO

setting if you can.

Press the

buttons to choose DigiPure Pro

1 Press the 6 buttons to choose DIGITAL

VNR

2 Press the 5buttons to choose a setting

2 Press the 5 buttons to choose a setting

AUTO:

The TV will automatically adjust the level of the DigiPure

effect to match the amount of noise in the picture, giving

the best possible picture.

AUTO:

The TV will automatically adjust the level of the DIGITAL

VNR effect to match the amount of noise in the picture,

giving you the best possible picture.

MIN:

The level of DigiPure effect is set to the minimum. When

you set the DigiPure Pro function to AUTO and notice

some noise, change the setting from AUTO to MIN.

• The MIN setting is not suitable for high-quality pictures

which contain very little noise.

MIN:

The level of the DIGITAL VNR effect is set to the

minimum. If you set the DIGITAL VNR function to AUTO

but feel that the sharpness of the original picture has not

been reproduced fully, change the setting from AUTO to

MIN.

• The MIN setting is not suitable for low-quality pictures

which contain a lot of noise.

MAX:

The level of DigiPure effect is set to the maximum. If you

set the DigiPure Pro function to AUTO but feel that the

original picture quality has not been reproduced fully,

change the setting from AUTO to MAX.

• The MAX setting is not suitable for low-quality pictures

which contain a lot of noise.

MAX:

The level of the DIGITAL VNR effect is set to the

maximum. If you set the DIGITAL VNR function to AUTO

but still notice some noise, change the setting from

AUTO to MAX.

• The MAX setting is not suitable for high-quality pictures

which contain very little noise.

OFF:

The DigiPure Pro function is turned off.

3 Press the

setting

button to complete the

3 Press the

setting

button to complete the

The menu disappers.

The menu disappears.

Picture features

I COLOUR SYSTEM

The colour system is chosen automatically. However, if the

picture is not clear or no colour appears, choose the colour

system manually.

4:3 AUTO ASPECT

PANORAMIC

REGULAR

14:9 ZOOM

BACK

1 Press the 6 buttons to choose COLOUR

SYSTEM. Then press the

button

D0017-EK

The sub-menu of the COLOUR SYSTEM function

appears.

2 Press the

mode

buttons to choose a ZOOM

button to complete the

COLOUR SYSTEM

3 Press the

setting

MAIN

SUB

PAL

AUTO

The menu disappears.

BACK

I PICTURE TILT

Sometimes the Earth’s own magnetic field may make the

picture tilt. If this happens, you can correct the picture tilt.

D0016-EK

Press the5 buttons to choose MAIN or SUB

MAIN:

You can change the colour system of the main-picture.

SUB:

1 Press the

buttons to choose PICTURE

button

TILT. Then press the

The sub-menu of the PICTURE TILT function appears.

You can change the colour system of the sub-picture.

• Choose MAIN when a sub-picture is not displayed.

PICTURE TILT

3 Press the

buttons to choose the

appropriate colour system

BACK

PAL:

PAL system

NTSC 3.58:

D0018-EK

NTSC 3.58 MHz system

NTSC 4.43:

NTSC 4.43 MHz system

AUTO:

This function detects a colour system from the input

signal. You can only use this when you are viewing a

picture from programme number PR 0 (AV), or an EXT

terminal.

2 Press the

becomes level

buttons until the picture

button to complete the

3 Press the

setting

The menu disappears.

4 Press the

setting

button to complete the

I PIP POSITION

You can choose one of four positions for the sub-picture.

The menu disappears.

1 Press the

buttons to choose PIP

• The AUTO function may not work properly if you

have poor signal quality. If the picture is abnormal in

the AUTO function, choose another colour system

manually.

POSITION. Then press the

button

The PIP POSITION menu appears.

• You cannot choose NTSC 3.58 or NTSC 4.43 for

programme numbers PR 0 (AV) to PR 99.

PIP POSITION

I 4:3 AUTO ASPECT

You can choose one of three ZOOM modes, REGULAR,

PANORAMIC or 14:9 ZOOM, as the ZOOM mode for the

normal picture (4:3 aspect ratio).

BACK

D0053-EK

1 Press the 6 buttons to choose 4:3 AUTO

2 Press the 5 buttons to choose the

ASPECT. Then press the

button

position

The sub-menu of the 4:3 AUTO ASPECT function

appears.

3 Press the

setting

button to complete the

The menu disappears.

Sound setting

I Sound adjustment

You can adjust the sound to your liking.

SOUND SETTING

1 Press the 6 buttons to choose an item

STEREO/

BASS

TREBLE

BALANCE

2 Press the 5 buttons to adjust it

BBE

OFF

SPEAKER

SUBWOOFER

HEADPHONE

Item

BASS

Weaker

Left

Stronger

Right

BACK

TREBLE

BALANCE

D0054-EK

3 Press the

setting

button to complete the

The menu disappears.

SOUND SETTING

STEREO/

BASS

I BBE

TREBLE

BALANCE

You can use the BBE function to enjoy easy-to-listen sound

that is faithful to the original sound recorded.

BBE

SPEAKER

HEADPHONE

OFF

1 Press the 6 buttons to choose BBE.

BACK

2 Press the 5 buttons to choose ON.

D0019-EK

To cancel the BBE function:

Press

buttons to choose OFF.

To display the SOUND SETTING menu:

3 Press the

setting.

button to complete the

1 Press the

button to display the MENU

(main menu)

The menu disappears.

2 Press the

buttons to choose SOUND

SETTING. Then press the

button

• Licensed by BBE Sound, Inc. BBE is a registered

trademark of BBE Sound, Inc.

I STEREO / I•II

I SPEAKER

Set the SPEAKER function to OFF when external front

speakers are connected to the TV. If the SPEAKER function

is set to OFF, no sound comes from the TV speakers.

When you are viewing a bilingual broadcast programme, you

can choose the sound from Bilingual I (Sub I) or Bilingual II

(Sub II). If you have poor reception on a stereo broadcast, you

can change from stereo to mono sound so that you can hear

the broadcast more clearly and easily.

Press the

buttons to choose SPEAKER

Press the

STEREO / I • II

buttons to choose

Press the 5 buttons to choose ON or OFF

2 Press the

mode

buttons to choose a sound

Press the

setting

button to complete the

s: Stereo sound

The menu disappears.

v : mono sound

t : Bilingual I (sub I)

• To hear sound from the TV speakers, set the

SPEAKER function to ON.

u : Bilingual II (sub II)

• The “SPEAKER” item is not displayed when the

3D-PHONIC function or DOLBY DIGITAL function

are operating. (Only AV32P10EK and AV32P10EI)

3 Press the

button to complete the

setting

The menu disappears.

• The sound mode you can choose differs depending

on the TV programme.

• This function does not work in the EXT modes. And

this function does not appear in the SOUND

SETTING menu.

Sound setting

SUBWOOFER (Only

I HEADPHONE

You need to use the HEADPHONE menu to adjust the

volume of the headphones.

AV32P10EK and AV32P10EI)

Set the SUBWOOFER function to ON when the subwoofer is

connected to the TV.

The HEADPHONE menu can also be used to set whether or

not sound is emitted from the TV speakers when the

headphones are being used and to perform the settings for

the sound emitted from the headphones.

1 Press the 6 buttons to choose

SUBWOOFER

1 Press the 6 buttons to choose

HEADPHONE. Then press the

button.

Press the 5 buttons to choose ON or OFF

The sub-menu of the HEADPHONE function appears.

Press the

setting

button to complete the

HEADPHONE

VOLUME

OFF

MAIN

SUB

The menu disappears.

• Set the SUBWOOFER function to OFF when the

subwoofer is not connected to the TV.

TV SPEAKER

OUTPUT

BACK

• When the 3D-PHONIC function or DOLBY DIGITAL

function is operating, the “SUBWOOFER” item does

not appear.

D0044-EK

• This function cannot be cancelled even if you

connect the headphones to the TV.

2 Press the 6 buttons to choose a

function. Then press the

change the setting

buttons to

VOLUME:

You can change the volume of the headphones.

TV SPEAKER:

You can turn the TV's speakers on or off.

ON:

The sound is emitted from the TV's speakers when

using the headphones.

OFF:

The sound is not emitted from the TV's speakers

when using the headphones.

• The sound from the external front speakers L/R and

the subwoofer cannot be stopped even if you set the

TV SPEAKER to OFF and connect the headphones

to the TV. If you want to stop the sound from the

external front speakers L/R and the subwoofer,

please turn off all amplifiers connected to the TV.

OUTPUT

You can choose the sound output to the headphones.

MAIN:

You can listen to the sound of the main-picture with

your headphones.

SUB:

You can listen to the sound of the sub-picture with

your headphones.

• When a sub-picture is not displayed, the sound of

the programme which is currently being viewed is

output to the headphones irrespective of the

OUTPUT setting.

•

When a sub-picture is displayed, the sound of the

sub-picture can be listened to with the headphones

while listening to the sound of the main-picture with

the TV speakers. In order to do this, set TV SPEAKER

to ON and OUTPUT to SUB.

3 Press the

setting

button to complete the

The menu disappears.

DIGITAL SURROUND (Only AV32P10EK

and AV32P10EI)

• This function does not work properly except for Dolby

Surround encoded programmes and Dolby Digital

DIGITAL SURROUND

programmes.

3D-PHONIC

DOLBY DIGITAL

DANCE CLUB

CONCERT HALL

I DOLBY DIGITAL

You can enjoy the surround sound of Dolby* Digital

STADIUM

SURROUND OFF

BACK

programmes and Dolby Surround encoded programmes.

When viewing a programme from the EXT

terminal which has been set to DIGITAL-IN:

You can enjoy the surround sound of Dolby Digital

programmes.

If the programme source has 5.1-channel Dolby Digital

soundtracks, you can enjoy the 5.1-channel Dolby Digital

surround sound.

D0045-EK

You can enjoy the surround sound with any of the five

surround functions.

1 Press the a button to display MENU

(main menu)

When viewing the Dolby Surround encoded programmes, you

can enjoy the Dolby Surround Pro Logic surround sound.

2 Press the 6 buttons to choose DIGITAL

When viewing a programme from the EXT

terminal which has not been set to DIGITAL-IN,

or when viewing a TV broadcasting programme:

When viewing the Dolby Surround encoded programmes, you

can enjoy the Dolby Surround Pro Logic surround sound.

SURROUND. Then press the OK button

The DIGITAL SURROUND menu is not displayed while

the headphones are connected to the TV. Disconnect

the headphones from the TV.

3 Press the 6 buttons to choose the

• Additional surround speakers are necessary in order to

use this function to enjoy surround sound. Although you

can listen to Dolby Digital audio without surround

speakers, you cannot enjoy surround sound such as

5.1-channel Dolby Digital surround sound.

function you want to use

To cancel a surround function:

Press the 6 buttons to choose SURROUND OFF.

• Before using this function, correctly set each of the items

in the DOLBY DIGITAL menu in accordance with “DOLBY

DIGITAL setting” on page 24.

Press the

button to complete the setting

The menu disappears.

• Dolby Digital soundtracks can provide anything from

mono to full 5.1-channel Dolby Digital surround sound.

When a Dolby Digital audio signal is received, the

number of front channels and rear channels included in

the signal are displayed on the screen for a few seconds

as “DOLBY D (number of front channels) / (number of

rear channels)”. If LFE (low frequency effects) are

included in the signal, “ .1” is displayed after the number

of rear channels. For example, “DOLBY D 3/2.1” is

displayed when a 5.1-channel Dolby Digital signal is

received.

• When you connect the headphones, all surround

functions will be cancelled.

I 3D-PHONIC

Dolby Surround Pro Logic surround sound and Dolby Digital

surround sound can be easily enjoyed without additional

surround speakers.

Using rear surround signals of Dolby Surround encoded

programmes or Dolby Digital programmes, this function will

create the surround sound as if surround speakers were

located to your right and left.

• This function does not work properly except for Dolby

Surround encoded programmes and Dolby Digital

programmes.

When viewing a programme from the EXT

terminal which has been set to DIGITAL-IN:

You can enjoy the atmosphere of the surround sound of

Dolby Digital programmes.

If the programme source has 5.1-channel Dolby Digital

soundtracks, you can enjoy the atmosphere of the

5.1-channel Dolby Digital surround.

When viewing Dolby Surround encoded programmes, you

can enjoy the atmosphere of Dolby Surround Pro Logic

surround sound.

* Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are

trademarks of Dolby Laboratories.

• Dolby Digital is an advanced form of digital audio coding.

Dolby Digital audio is available from programme sources

(such as DVD-video discs) which are usually identified

with a Dolby Digital logo.

• When you connect the subwoofer system to the TV, you

can enjoy the powerful low frequency effects (LFE) of

5.1-channel Dolby Digital more effectively.

• This TV does not work with digital audio signals other than

Dolby Digital audio. If no sound is emitted from the

speakers, cancel the DIGITAL-IN setting and change to

normal analog sounds.

When viewing a programme from the EXT

terminal which has not been set to DIGITAL-IN,

or when viewing a TV broadcasting programme:

When viewing Dolby Surround encoded programmes, you

can enjoy the atmosphere of Dolby Surround Pro Logic

surround sound.

• You can turn this function on or off with a single press. For

details, see “4 3D Button (Only AV32P10EK and

AV32P10EI)” on page 12.

•

For details of how to adjust the surround effect level, adjust

the volume balance of the speakers, and perform the

setting necessary when adding a front speaker system or

subwoofer system, see “3D-PHONIC setting” on page 24.

DIGITAL SURROUND (Only AV32P10EK and AV32P10EI)

DOLBY DIGITAL setting

I Other surround functions

Correctly set the items in the sub-menu of the DOLBY

DIGITAL function, and use the test signal to control the

volume level of the speakers so that you can listen to the

sounds from them uniformly. Be sure to do this before using

the DOLBY DIGITAL function.

DANCE CLUB:

This function creates a dance club atmosphere.

CONCERT HALL:

This function creates a concert hall atmosphere.

STADIUM:

This function creates a stadium atmosphere.

1 Press the 6 buttons to choose DOLBY

DIGITAL. Then press the 3 button

• The above function does not appear in the DIGITAL

SURROUND menu when viewing a programme from the

EXT terminal which has been set to DIGITAL-IN.

The sub-menu of the DOLBY DIGITAL function appears.

DOLBY DIGITAL

• The above function does not work properly for the Dolby

Surround encoded programmes or mono sound

programmes.

L/C/R

OFF

CENTRE

OFF

TV SPEAKER

REAR SPEAKER

SUBWOOFER

TEST MODE

VOLUME

LEFT

3D-PHONIC setting

CENTRE

RIGHT

1 Press the 6 buttons to choose

DELAY TIME

3D-PHONIC. Then press the 3 button

The sub-menu of the 3D-PHONIC function appears.

BACK

D0047-EK

3D-PHONIC

TV SPEAKER

SUBWOOFER

L/C/R

OFF

CENTRE

OFF

2 Press the 6 buttons to choose an item.

Then press the 5 buttons to change the

setting

LEVEL

VOLUME

LEFT

CENTRE

RIGHT

TV SPEAKER:

Only set to CENTRE when the front speakers are

connected to the TV. Otherwise set to L/C/R.

BACK

D0046-EK

REAR SPEAKER:

Set to ON when the rear speaker is connected to the TV.

Otherwise set to OFF. However, you cannot enjoy

surround sound when it is set to OFF.

2 Press the 6 buttons to choose an item.

Then press the 5 buttons to change the

setting

SUBWOOFER:

Set SUBWOOFER to ON when the subwoofer system is

connected to the TV. Otherwise, set to OFF.

TV SPEAKER:

Only set to CENTRE when the front speakers are

connected to the TV. Otherwise set to L/C/R.

TEST MODE/VOLUME (LEFT/CENTRE/RIGHT/

LS/RS):

Set the volume balance of the speakers so that the

correct surround effect can be achieved.

When the other settings have been completed, adjust in

accordance with “Adjusting the volume balance with the

TEST MODE” on page 25.

SUBWOOFER:

Set SUBWOOFER to ON when the subwoofer system is

connected to the TV. Otherwise, set to OFF.

LEVEL:

You can control the effect level of the 3D-PHONIC

function as you like.

DELAY TIME:

VOLUME (LEFT/CENTRE/RIGHT):

A delay can be applied to SURROUND (surround

sound) and CENTRE (centre sound) depending on the

arrangement of the speakers.

Select DELAY TIME and press the 3 button to display

the DELAY TIME menu. The DELAY TIME is changed in

1ms steps every time the 5 buttons are pressed.

You can adjust the sound level of each speaker

individually. LEFT/RIGHT denotes left and right of the

front speakers and CENTRE denotes the centre

speaker.

Press the OK button to complete the setting

DELAY TIME

The menu disappears.

• When a speaker system is not connected to the TV, set

TV SPEAKER to L/C/R and SUBWOOFER to OFF.

Otherwise the sound will not be emitted correctly.

SURROUND

CENTRE

BACK

• When you do not want to hear sound from the TV

speakers, set TV SPEAKER to OFF.

•

If you set TV SPEAKER to CENTRE or OFF, the sound from

the subwoofer can be heard only when listening to the

Dolby Digital sound with the Low Frequency effect (LFE).

If you want to hear sound from the subwoofer every time,

set TV SPEAKER to L/C/R.

D0048-EK

DIGITAL SURROUND (Only AV32P10EK and AV32P10EI)

3 Press the OK button to complete the

setting

4 Press the a button to complete the

settings

The menu disappears.

• When a speaker system is not connected to the TV, set

TV SPEAKER to L/C/R and SUBWOOFER to OFF.

Otherwise the sound will not be emitted correctly.

• When you do not want to hear sound from the TV

speakers, set TV SPEAKER to OFF.

• When using the front speaker system or subwoofer

system with the TV, it is recommend that this TEST MODE

is used to adjust the speaker volume levels each time the

system is used.

• The CENTRE (centre sound) DELAY TIME cannot be

adjusted when the TV SPEAKER is set to L/C/R.

•

If you set TV SPEAKER to CENTRE or OFF, the sound from

the subwoofer can be heard only when listening to the

Dolby Digital sound with the Low Frequency effect (LFE).

If you want to hear sound from the subwoofer every time,

set TV SPEAKER to L/C/R.

Adjusting the volume balance with

the TEST MODE

Use the test signal to adjust the volume level of each speaker

so that they are all the same.

Preparation:

• The TV volume cannot be adjusted after the menu is

displayed. Increase the TV volume level to about 10 before

displaying the menu.

1 Display the sub-menu of the DOLBY

DIGITAL function

2 Press the 6 buttons to choose TEST

MODE. Then press the 5 buttons to

choose ON

Test signals are output from each of the speakers in turn.

When using the front speaker system and/or

subwoofer system with the TV:

Turn on the power of each amplifier, slowly increase the

amplifiers’ volumes until the sound emitted from each

speaker connected to the system is about the same as

that of the sound emitted from the TV speakers. Note

that increasing the amplifier volume too high may

damage the speakers.

Stopping the test signal:

Press the 6 buttons to choose TEST MODE and

press the 5 buttons to choose OFF.

3 Press the 6 buttons to adjust the sound

volume of each of the speakers.

Adjust the sound volumes so that you can listen to the

sounds at the same volume when you are sitting where

you would normally sit to watch the TV.

LEFT/RIGHT:

The left or right of the front speakers

CENTRE:

The centre speaker

LS/RS:

The left or right of the surround speakers

If REAR SPEAKER is set to OFF, LS and RS are not

displayed.

EXT SETTING

3 Press the

setting.

button to complete the

The menu disappears.

EXT SETTING

EXT-1

• The EXT-1 terminal does not support S-VIDEO signal

(Y/C signal) and you cannot set S-IN (S-VIDEO

input) in the EXT-1 terminal.

• Setting S-IN (S-VIDEO input) changes the head

character from “E” to “S”. When an EXT terminal

receives a normal video signal, “E1”, “E2”, “E3” or

“E4” appears on the display. This changes to “S2”,

“S3” or “S4” when it receives an S-VIDEO signal.

DUBBING

EXT-2

EXT-3

EXT-4

BACK

ID LIST

S-IN

DIGITAL-IN

•

Even a device which can output an S-VIDEO signal

(Y/C signal) may output a regular video signal

(composite signal) depending on the device setting. If

a picture cannot appear because the S-IN (S-VIDEO

input) setting has been made, read the device

instruction manual carefully again to check for the

device settings.

D0055-EK

EXT SETTING

EXT-1

DUBBING

EXT-2

EXT-3

EXT-4

I DIGITAL-IN (Only

AV32P10EK and AV32P10EI)

When connecting a device (such as a DVD player) which

enables Dolby Digital audio signal to be output, you can listen

to Dolby Digital audio.

BACK

ID LIST

S-IN

Preparation:

D0020-EK

• In order to listen to Dolby Digital audio, correctly connect a

device to the TV in accordance with “Listening to Dolby

Digital audio (Only AV32P10EK and AV32P10EI)” on

page 38.

To display the EXT SETTING menu:

1 Press the

button to display the MENU

(main menu)

2 Press the 6 buttons to choose EXT

SETTING. Then press the button

• If DIGITAL-IN is set by mistake when no device is connected

to the DIGITAL AUDIO IN terminal, no sound is emitted.

1 Press the 6 buttons or 5 buttons to

choose an EXT terminal

I S-IN (S-VIDEO input)

You can connect a device (such as an S-VHS VCR) to enjoy

the high-quality picture of the S-VIDEO signal (Y/C signal).

Press the green button to set the DIGITAL-IN

Pressing the green button repeatedly until the mark

selected is the same as the type of cable connected to

the DIGITAL AUDIO IN terminal.

Preparation:

• First read the device’s instruction manual and

“Further preparation” on page 37 to connect the device to

the TV properly. Second, follow the device’s instruction

manual to set the device so that it sends an S-VIDEO signal

(Y/C signal) to the TV.

: Select this mark when connected with coaxial

cable.

: Select this mark when connected with optical

cable.

• Do not set S-IN (S-VIDEO input) to an EXT terminal

connected to a device which cannot output an S-VIDEO (Y/

C signal). If it is set wrongly, a picture cannot appear.

To cancel the DIGITAL-IN setting:

Press the green button to turn off the mark of DIGITAL-IN.

Press the

button to complete the setting

1 Press the

buttons or

choose an EXT terminal

buttons to

The menu disappears.

• DIGITAL-IN cannot be set for the TV and EXT-4

terminal.

• This TV does not work with digital audio signals

other than Dolby Digital audio. If no sound is emitted

from the speakers, cancel the DIGITAL-IN setting

and change to normal analog sounds.

2 Press the yellow button and set the S-IN

(S-VIDEO input)

An y (S-VIDEO input) mark is displayed. You can

view an S-VIDEO signal (Y/C signal) instead of the

regular video signal (composite signal).

To cancel the S-IN (S-VIDEO input) setting:

Press the yellow button and turn off the y (S-VIDEO

input) mark.

The regular video signal (composite signal) pictures are

resumed.

EXT SETTING

I ID LIST

You can store a name for each of the devices connected to

each EXT terminal. Giving a name to an EXT terminal makes

the EXT terminal number appear on the screen, together with

its name.

I DUBBING

You can choose a signal source to be output from the EXT-2

terminal.

You can do this with the output signal of the device connected

to another EXT terminal, or the picture and sound from a TV

channel you are currently viewing.

1 Press the 6 buttons or 5 buttons to

choose an EXT terminal

1 Press the 5buttons to choose the arrow

from the menu.

2 Press the blue button to display the name

list (ID LIST)

2 Press the 6 buttons to choose another

EXT SETTING

EXT terminal or TV.

ID LIST

VHS

EXT-1

EXT-3

EXT-4

EXT SETTING

EXT-1

EXT SETTING

EXT-1

DUBBING

EXT-2

S-VHS

DUBBING

EXT-2

DUBBING

EXT-2

EXT-3

EXT-4

EXT-3

EXT-4

DVC

SAT

STB

GAME

DVD

8mm

Hi-8

BACK

EXT SETTING

EXT-1

EXT SETTING

EXT-1

D0021-EK

DUBBING

EXT-2

DUBBING

EXT-2

EXT-3

EXT-4

EXT-3

EXT-4

3 Press the 6 buttons to choose a name.

Then press the button.

BACK

D0022-EK

The ID LIST disappears and the name is assigned to the

EXT terminal.

The arrow in the menu represents a signal flow. The left

side of the arrow shows a signal source output from the

EXT-2 terminal.

To erase a name assigned to the EXT terminal:

Choose a blank space.

EXT-1/EXT-3/EXT-4:

4 Press the

setting.

button to complete the

The output signal of the device connected to an EXT

terminal passes through the TV and is output from the

EXT-2 terminal.

The menu disappears.

TV:

• You cannot choose an EXT terminal name that is not

on the name list (ID LIST).

The picture and sound of the TV channel you are

currently viewing are output from the EXT-2 terminal.

3 Press the

setting.

button to complete the

The menu disappears.

• During dubbing, you should not turn off the TV.

Turning off the TV also turns off the output from the

EXT-2 terminal.

• When you choose an EXT terminal as an output, you

can view a TV programme or a picture from the other

EXT terminal while dubbing the picture from a

device connected to the EXT terminal onto a VCR

connected to the EXT-2 terminal.

• The RGB signals from TV games cannot be

output.

• Teletext programmes cannot be output.

• The sub-picture displayed by the PIP function

cannot be output.

• The still picture displayed by the FREEZE function

cannot be output.

•

The sound from the EXT terminal set to DIGITAL-IN

cannot be output. (Only AV32P10EK and AV32P10EI)

FEATURES

I BLUE BACK

FEATURES

You can set the TV to automatically change to a blue screen

and mute the sound if the signal is weak or absent, or when

there is no input from an external device.

SLEEP TIMER

BLUE BACK

OFF

CHILD LOCK

DECODER(EXT-2)

BACK

Press the

buttons to choose BLUE BACK

2 Press the5 buttons to choose ON

D0023-EK

To cancel the BLUE BACK function:

Press the5 buttons to choose OFF.

To display the FEATURES menu:

1 Press the

button to display the MENU

Press the

button to complete the setting

(main menu)

The menu disappears.

2 Press the6 buttons to choose

FEATURES. Then press the

button

I CHILD LOCK

When there is a TV channel you do not want your children to

watch, you can use the CHILD LOCK function to lock out the

TV channel. Even when a child chooses a programme

number (PR) for a locked TV channel the screen will change

I SLEEP TIMER

You can set the TV to automatically turn off after a set time.

to blue and display (CHILD LOCK) so the TV channel

1 Press the 6 buttons to choose SLEEP

cannot be viewed. Unless you enter a pre-set ID number by a

special operation, the lock cannot be released and the child

cannot view the TV channel.

TIMER. Then press the

button

A sub-menu of the SLEEP TIMER function appears.

To set the CHILD LOCK function

SLEEP TIMER

120

1 Press the 6 buttons to choose CHILD

LOCK. Then press theo button.

“SET ID NO.” (ID number setting screen) appears.

OFF

BACK

SET ID NO.

0000

D0024-EK

2 Press the 5buttons to set the period of

BACK

time

You can set the time for up to 120 minutes (2 hours) in

10 minute steps.

D0025-EK

To cancel the SLEEP TIMER function:

Press the 2button to set the period of time to “OFF.”

To set the ID number you want

1 Press the6 buttons to choose a number

2 Press the5 buttons to move the cursor

3 Press the

setting

button to complete the

3 Press the

button.

The menu disappears.

• One minute before the SLEEP TIMER function turns

off the TV, “GOOD NIGHT!” appears.

The sub-menu of CHILD LOCK appears.

CHILD LOCK

• The SLEEP TIMER function cannot be used to turn

off the TV’s main power.

BBC1

BBC2

ITV

CH4

CH5

• When the SLEEP TIMER function is on, you can

display the sub-menu of the SLEEP TIMER function

again to confirm or change the remaining period of

time of the SLEEP TIMER function. Press the

button to leave the menu after confirming or

changing the remaining time.

LOCK

BACK

D0026-EK

Press the6 buttons to choose a TV channel

Every time you press the 6 buttons, the programme

number (PR) changes, and the picture of the TV channel

registered in the programme number (PR) is displayed

on the screen.

FEATURES

5 Press the blue button and set the CHILD

LOCK function

I DECODER (EXT-2)

You can only use this function if you have a decoder

connected to a T-V LINK compatible VCR, which in turn is

connected to the EXT-2 terminal. To use this function, see

“Using the DECODER (EXT-2) function” on page 35.

(CHILD LOCK) appears and the TV channel is locked.

To reset the CHILD LOCK function:

Press the blue button again.

• If you have not connected a decoder with a T-V LINK

compatible VCR to the EXT-2 terminal, setting this function

to “ON” by mistake causes the picture/sound of a TV

channel you are currently viewing to disappear.

(CHILD LOCK) disappears.

6 Press the

setting

button to complete the

The menu disappears.

• To disable easy resetting of the CHILD LOCK

function, the menu disappears if you choose the

CHILD LOCK function and press the

button.

To view a locked TV channel

1 Choose a programme number (PR) for a

locked TV channel, by using the number

buttons or PR LIST

The screen changes to blue and the (CHILD LOCK)

appears. You cannot view the TV channel.

D0027-EK

2 Press the h (information) button to

display “ID NO.” (ID NO. input screen)

ID NO . :

D0028-EK

3 Press the number buttons to enter the ID

number

The lock is temporarily released so you can view the TV

channel.

If you have forgotten the ID number:

Perform step 1 of “To set the CHILD LOCK function”.

After confirming the ID number, press the

exit the menu.

button to

• Even if you reset the lock temporarily, it does not

mean that the CHILD LOCK function set for the TV

channel is cancelled. The next time anyone tries to

view the TV channel, it will be locked again.

• When you want to cancel the CHILD LOCK function,

you must perform the operation “To set the CHILD

LOCK function” again.

• To stop it being easy to choose the programme

number (PR) of a locked TV channel, the

programme number (PR) has been set so that it

cannot be chosen by the

of the TV.

buttons or the buttons

• To stop it being easy to reset the lock, “ID NO.” (ID

NO. input screen) is set so that it cannot appear

unless you press the

(Information) button.

INSTALL

If “ACI START/ACI SKIP” appears in the AUTO

PROGRAM menu:

INSTALL

You can use the ACI (Automatic Channel Installation)

function to decode the ACI data and complete the

registration of all the TV channels quickly. For details of

the ACI function and how to use it, see “Using the ACI

function” on page 35.

LANGUAGE

AUTO PROGRAM

EDIT / MANUAL

BACK

If you don’t want to use the ACI function, press the

D0029-EK

button to choose ACI SKIP and then press

To cancel the AUTO PROGRAM function:

Press the button.

To display the INSTALL menu:

1 Press the

button to display the MENU

(main menu)

3 After the TV channels have been stored in

the programme numbers (PR) list, the EDIT

menu appears

2 Press the

buttons to choose the

INSTALL menu. Then press the

button

You can now edit the programme numbers (PR) list

using the EDIT/MANUAL function. For details, see

“EDIT/MANUAL” on page 31.

I LANGUAGE

You can choose the language you want to use for the

on-screen display from the language list in the menu.

When not using the EDIT/MANUAL function:

If you do not need to use the EDIT/MANUAL function, go

to the next step.

1 Press the

buttons to choose

LANGUAGE. Then press the

button

A sub-menu of the LANGUAGE function appears.

4 Press the

button to display the T-V

LINK menu

LANGUAGE

T-V LINK

DOWNLOAD TV

VCR

BACK

EXIT

D0005-EK

D0002(E)-EK

2 Press the 5and

buttons to choose a

5 Operate the T-V LINK menu according to

the type of video cassette recorder (VCR)

you have connected to the EXT-2 terminal

language

3 Press the

setting

button to complete the

If you do not have a T-V LINK compatible VCR

connected:

The menu disappears.

Press the

button to leave the T-V LINK menu.

The T-V LINK menu disappears, and all the settings are

completed.

I AUTO PROGRAM

You can automatically store the TV channels for which you

have the best reception. Store them in the TV’s programme

numbers (PR) list by doing the following.

If you have a T-V LINK compatible VCR

connected:

See “Downloading data to a VCR” on page 35 to

transmit the programme number (PR) data to the VCR.

1 Press the

PROGRAM

buttons to choose AUTO

• If a TV channel you want to view is not set to a

programme number (PR), set it manually using the

MANUAL function. For details, see “EDIT/MANUAL”

on page 31.

2 Press the

button to start the AUTO

PROGRAM function

The AUTO PROGRAM menu appears and the TV

channels you receive are automatically registered in the

programme numbers (PR) list.

• The AUTO PROGRAM function does not set the

programme number PR 0 (AV) for your video

cassette recorder. You will need to set this using the

manual function.

• In some areas you may get TV reception from more

than one transmitter, for example different ITV

regions. In this case each TV channel could be set

twice. If this happens, the first set of channels will

have the stronger signal. If you want to delete the

second set of channels, you will have to do it

manually (see page 33).

AUTO PROGRAM

EDIT

CH 10

20%

BBC1

BBC2

ITV

CH4

CH5

BACK

MOVE

INSERT

DELETE

MANUAL

D0004-EK

INSTALL

2 Follow the options for the function you

want to use

I EDIT/MANUAL

The EDIT/MANUAL functions are divided into two types:

• editing the current programme numbers (PR)

(EDIT functions); and

3 Press the

settings

button to complete the

• manually storing a TV channel you want to view as a

programme number (PR) (MANUAL function).

The T-V LINK menu appears.

Here are the details about these functions:

T-V LINK

MOVE:

DOWNLOAD TV

VCR

This function changes the programme number (PR) of a TV

channel.

BACK

ID:

This function registers a channel name (ID) to a TV channel.

EXIT

D0005-EK

INSERT:

This function adds a new TV channel in the current

programme numbers (PR) list by using the CH/CC number.

4 Follow the T-V LINK menu according to the

type of VCR you have connected to the

EXT-2 terminal

DELETE:

This function deletes a TV channel you do not want to list.

If you do not have a T-V LINK compatible VCR

connected:

MANUAL:

This function manually stores a new TV channel in a

programme number (PR).

Press the

button to leave the T-V LINK menu.

The T-V LINK menu disappears and all the settings are

completed.

• For programme number PR 0, “AV” appears in the

programme numbers (PR) list.

• An EXT terminal number does not appear in the

programme numbers (PR) list.

• The CH/CC number is a number unique to the TV and

corresponds to the channel number of a TV channel. For

the relationship between a channel number and a CH/CC

number, see “CH/CC NUMBER” on page 33.

• You cannot use the INSERT function if you do not know

the channel number of a TV channel. Use the MANUAL

function to register a TV channel in the programme

number (PR) list.

If you have a T-V LINK compatible VCR

connected:

Follow the operating procedure “Downloading data to a

VCR” on page 35 to transmit the programme number

(PR) data to the VCR.

MOVE

1 Press the

channel

buttons to choose a TV

Every time you press the

buttons, the programme

number (PR) changes, and the picture of the TV channel

stored in the programme number (PR) appears on the screen.

Caution:

• Using the MOVE, DELETE or INSERT functions rewrites the

current programme numbers (PR) list. Therefore, the

programme numbers (PR) of some of the TV channels will

change.

2 Press the button to start the MOVE

function

• Using the MANUAL function for a TV channel for which the

CHILD LOCK function has been set cancels the CHILD

LOCK function for that channel.

EDIT

BBC1

BBC2

ITV

CH4

CH5

•

Using the MANUAL function for a TV channel for which the

DECODER (EXT-2) function has been set to ON returns the setting

of the DECODER (EXT-2) function for that channel to OFF.

• When a TV channel has already been registered in PR 99,

using the INSERT function deletes that TV channel.

BACK

1 Press the

buttons to choose EDIT/

MANUAL. Then press the

button

STORE

D0030-EK

EDIT

3 Press the

buttons to choose a new

BBC1

BBC2

ITV

CH4

CH5

programme number (PR)

To cancel the MOVE function:

Press the

(information) button.

BACK

MOVE

4 Press the button to change the

programme number (PR) of a TV channel

to a new programme number (PR)

INSERT

DELETE

MANUAL

D0038-EK

INSTALL

• You can give your own unique channel name (ID) to

the TV channel. When you have finished step 3, do

not go to step 4. Press the

buttons to move the

1 Press the

channel

buttons to choose a TV

cursor, and press the

buttons to choose each

character of the channel name (ID). Then press the

a button to register the channel name (ID) to the

TV channel.

Every time you press the

buttons, the programme

number (PR) changes, and the picture of the TV channel

stored in the programme number (PR) appears on the

screen.

INSERT

Preparation:

2 Press the red button to start the ID

function

• You need to find the CH/CC number for the TV channel.

Find the CH/CC number from the “CH/CC NUMBER” table

on page 33 based on the channel number of the TV

channel.

EDIT

1 Press the

buttons to choose a

BBC1

BBC2

ITV

CH4

CH5

Programme number (PR) for which you will

2 Press the green button and start the

INSERT function

ID LIST

BACK

EDIT

D0031-EK

BBC1

BBC2

ITV

CH4

CH5

3 Press the

buttons to choose the first

character of a channel name (ID) you want

to give the TV channel

BACK

EDIT

BBC1

BBC2

ITV

CH4

CH5

D0034-EK

To cancel the INSERT function:

Press the (Information) button.

3 For UK model (AV32P10EK/AV32L5EK):

Press the number buttons to enter the

remaining CH number.

ID LIST

BACK

D0032-EK

• You cannot enter CC numbers.

4 Press the blue button to display the ID LIST

(channel name list)

For Ireland model (AV32P10EI/AV32L5EI):

Press the

buttons to choose “CH” or

ID LIST

“CC”, then enter the remaining CH or CC

number.

EDIT

MBC

MCM

MDR

MOVIE

MTV

BBC1

BBC2

ITV

CH4

CH5

The TV shifts to registration mode.

When the registration is completed, the picture of the TV

channel appears on the screen.

MTV3

• The CH/CC number is a number given to each

broadcast frequency that carries a TV channel. If the

TV cannot detect the TV channel corresponding to

the broadcast frequency indicated by the CH/CC

number, a “no-signal” picture appears.

BACK

D0033-EK

5 Press the

buttons to choose the

channel name (ID)

To cancel the ID function:

Press the

(Information) button.

6 Press the

button to give a channel

name (ID) to a TV channel

INSTALL

DELETE

I CH/CC NUMBER

• When you want to use the INSERT function on page 32,

find the CH/CC number corresponding to the channel

number of the TV channel from this table.

1 Press the 6 buttons to choose a TV

channel

If you want to know a particular TV channel’s channel

menu, look in TV listings magazines or contact the

broadcaster.

Every time you press the 6 buttons, the programme

number (PR) changes over, and the picture of the TV

channel stored in the programme number list (PR)

appears on the screen.

• The UK model (AV32P10EK/AV32L5EK) cannot receive

the CC number channels or the channels from CH 02 to

CH 12.

2 Press the yellow button to delete the TV

channel

Channel

E40

E41

E42

E43

E44

E45

E46

E47

E48

E49

E50

E51

E52

E53

E54

E55

E56

E57

E58

E59

E60

E61

E62

E63

E64

E65

E66

E67

E68

E69

The TV channel is deleted from the programme numbers

(PR) list.

CH 02

CH 03

CH 04

CH 05

CH 06

CH 07

CH 08

CH 09

CH 10

CH 11

CH 12

CH 21

CH 22

CH 23

CH 24

CH 25

CH 26

CH 27

CH 28

CH 29

CH 30

CH 31

CH 32

CH 33

CH 34

CH 35

CH 36

CH 37

CH 38

CH 39

E2, IR A

CH 40

CH 41

CH 42

CH 43

CH 44

CH 45

CH 46

CH 47

CH 48

CH 49

CH 50

CH 51

CH 52

CH 53

CH 54

CH 55

CH 56

CH 57

CH 58

CH 59

CH 60

CH 61

CH 62

CH 63

CH 64

CH 65

CH 66

CH 67

CH 68

CH 69

E3, IR B, ITALY A

E4, IR C, ITALY B

E5, IR D, ITALY D

MANUAL

E6, IR E, ITALY E

E7, IR F, ITALY F

1 Press the

buttons to choose a

E8, IR G

E9, ITALY G

programme number (PR) for a new TV

E10, IR H, ITALY H

channel

E11, IR J, ITALY H+1

E12, ITALY H+2

E21

2 Press the blue button to activate the

MANUAL function

E22

E23

E24

E25

MANUAL

E26

E27

BBC1

BBC2

ITV

CH4

CH5

E28

E29

E30

E31

E32

E33

E34

BACK

E35

E36

FINE

E37

E38

D0035-EK

E39

To cancel the MANUAL function:

Press the (Information) button.

Channel

S31

CC 01

CC 02

CC 03

CC 04

CC 05

CC 06

CC 07

CC 08

CC 09

CC 10

CC 11

CC 12

CC 13

CC 14

CC 15

CC 16

CC 17

CC 18

CC 19

CC 20

CC 21

CC 22

CC 23

CC 24

CC 25

CC 26

CC 27

CC 28

CC 29

CC 30

CC 31

CC 32

CC 33

CC 34

CC 35

CC 36

CC 37

CC 38

CC 39

CC 40

CC 41

CC 75

CC 76

CC 77

CC 78

CC 79

S32

3 Press the green or red button to search for

a TV channel

S33

S34

S35

Scanning stops when the TV finds a TV channel. Then

the TV channel is displayed.

S36

S37

S38

S39

4 Press the green or red button repeatedly

until the TV channel you want appears

S10

S11

S12

S13

S14

S15

S16

S17

S18

S19

S20

S21

S22

S23

S24

S25

S26

S27

S28

S29

S30

S40

S41

If the TV channel reception is poor:

Press the blue or yellow button to fine-tune the TV

channel.

Z, ITALY C

Z+1

Z+2

5 Press the

button and register the TV

channel to a programme number (PR)

The normal EDIT menu appears.

DEMO

OFF

BACK

D0036-EK

To display the DEMO menu:

1 Press the

button to display the MENU

(main menu)

2 Press the 6 buttons to choose DEMO.

Then press the button

The DEMO function automatically demonstrates some of the

TV functions.

1 Press the 6 buttons to choose ON

2 Press the

setting

button to complete the

The DEMO function is set to ON, and the demonstration

will start.

To stop the demonstration:

Press one of the buttons on the remote control.

When the DEMO function is set to ON:

Each time the TV is turned on, the demonstration starts

automatically. If you do not want that to happen, cancel

the DEMO function:

1 Display the DEMO menu again

2 Press the6 buttons to choose OFF

3 Press the

function

button to cancel the DEMO

Other menus

I Using the ACI function

This TV has an ACI function which decodes the ACI

(automatic channel installation) data.

I Downloading data to a VCR

You can send the latest programme numbers (PR) data to a

VCR with the T-V LINK function.

Using the ACI function allows all TV channels transmitted

from the cable TV station to be properly registered quickly,

using the data from the cable TV station.

• You can only do this when a T-V LINK compatible VCR is

connected to the EXT-2 terminal.

• This only works when the T-V LINK menu is being

displayed.

Caution:

T-V LINK

If your cable TV station broadcasts ACI data and if “ACI

START/ACI SKIP” appears in the AUTO PROGRAM menu,

the ACI function is enabled. In all other cases, it is disabled.

DOWNLOAD TV

VCR

1 Press the 6 button to choose ACI

BACK

START. Then press the

the ACI function

button to start

EXIT

D0005-EK

When you don't want to use the ACI function:

Press the 6 button to choose ACI SKIP and then

1 Turn on the VCR

2 Press the button

press the

button.

If the AUTO PROGRAM menu changes to another

menu:

Depending on your cable TV station, there may be a

broadcast selection menu set up by the cable TV station.

The data transmission begins.

DOWNLOAD TV

VCR

Follow the menu instructions and use the 5and 6

TRANSFER. . . . .

buttons to operate the menu. After you have made the

D0037-EK

setting, press the

button.

The T-V LINK menu disappears once the data

transmission ends.

If “ACI ERROR” is displayed in the AUTO PROGRAM

When the T-V LINK menu changes over to

another menu:

The TV has finished its menu. This new menu is

operated from the VCR. See the VCR instruction

manual for what to do next.

menu:

“ACI ERROR” means that the ACI function is not

working properly. Press the

function again.

button to start the ACI

• If “FEATURE NOT AVAILABLE” appears at the T-V

If “ACI ERROR” still appears even after you have tried to

LINK menu, check the following three items. Then

start the ACI function several times, press the button

press the

button to retry data transmission.

to start the AUTO PROGRAM function. It does not cause

any problems because all the TV channels are

registered to the programme numbers (PR) by the

AUTO PROGRAM function.

− Has a T-V LINK compatible VCR been

connected to the EXT-2 terminal?

− Has the VCR power been turned on?

− Does the SCART cable that connects the EXT-2

terminal to the T-V LINK compatible VCR have all

its proper connections?

2 When the settings are completed, the EDIT

menu is displayed. Return to the

instructions that you were reading before,

and continue

I Using the DECODER (EXT-2)

When the “Initial Settings” have been made:

Return to step 5 of “Initial settings” on page 6

function

If you have a decoder connected to a T-V LINK compatible

VCR, which in turn is connected to the EXT-2 terminal, use

the DECODER (EXT-2) function to unscramble the

scrambled TV channels.

When the “AUTO PROGRAM” has been made:

Return to step 3 of “AUTO PROGRAM” on page 30

• If you have any questions about the items in the

cable TV station’s broadcast selection menu or how

to operate the menu, please contact your cable TV

station.

• When the cable TV broadcast reception is poor, the

ACI function will not work properly.

1 Turn on the decoder power

2 Display the scrambled TV channel on the

Even if the decoder is working, a scrambled picture

appears.

• If there is an error in the ACI data itself, the TV channel

cannot be registered properly. If this happens, turn

the ACI function off (ACI SKIP) and use the AUTO

PROGRAM function, or the EDIT/MANUAL function to

correct the programme number (PR) setting.

3 Press the

button to display the MENU

The MENU (main menu) appears.

Other menus

4 Press the

buttons to choose

FEATURES. Then press the

button.

The FEATURES menu appears.

FEATURES

SLEEP TIMER

BLUE BACK

OFF

CHILD LOCK

DECODER(EXT-2)

BACK

D0023-EK

5 Press the

buttons to choose

DECODER (EXT-2) . Then press the

buttons to choose ON

An unscrambled picture appears.

To cancel the DECODER (EXT-2) function:

Press the buttons to choose OFF.

6 Press the

setting

button to complete the

The T-V LINK menu appears.

T-V LINK

DOWNLOAD TV

VCR

BACK

EXIT

D0005-EK

7 Follow “Downloading data to a VCR” on

page 35 to transmit the programme

number (PR) data to the VCR

8 If you have another TV channel you want to

unscramble using a decoder, repeat steps

2 to 7.

• If the DECODER (EXT-2) function has been set to

“ON” but the TV channel cannot be unscrambled,

check the following:

− Has the decoder been connected to the VCR

properly according to the VCR and decoder

instruction manuals?

− Has the decoder power been turned on?

−

Can the TV channel be unscrambled with a

decoder?

− Do you need to change the VCR settings in order

to connect the decoder? Confirm that the VCR is

set properly by rechecking the VCR Instruction

manual.

Further preparation

I Connecting external equipment

Connect the equipment to the TV, making the correct rear

panel and front panel connections.

Behind the Cover

Before connecting anything:

• Read the manuals that came with the equipment.

Depending on the equipment, the connection method may

be different from the diagram. Also, the equipment settings

may need to change depending on the connection method.

• Turn off all the equipment including the TV.

• The “Specifications” on page 43 and the back cover give the

details of the EXT terminals. If you are connecting

equipment not listed in the following connection diagram,

see the table to choose the best EXT terminal.

• Connecting cables are not supplied.

1VCR (composite signal)

2VCR (composite signal/S-VIDEO signal)

3T-V LINK compatible VCR (composite signal/

S-VIDEO signal)

4Decoder

5DVD player (composite signal/S-VIDEO signal)

6DVD player (composite signal/RGB signal)

7TV game (composite signal/RGB signal)

8TV game (composite signal/S-VIDEO signal)

9Headphones

Side of the TV

0Camcorder (composite signal/S-VIDEO signal)

-SCART cable

=Audio cable

~Video cable

!S-VIDEO cable

EXT-2

EXT-3

EXT-1

Back of the TV

COAXIAL

DIGITAL

AUDIO IN

OPTICAL

SUB

WOOFER

AUDIO OUT

EXT-2

EXT-3

EXT-1

SURROUND

REAR

Further preparation

Equipment which can output the

S-VIDEO signal (Y/C signal) such as

an S-VHS VCR

I Listening to Dolby Digital

audio (Only AV32P10EK and

AV32P10EI)

In order to listen to Dolby Digital audio which is recorded as a

Dolby Digital programme source (such as a DVD-video disc),

connect the device and set the DIGITAL-IN as described

below.

Connect the equipment to an EXT terminal (but not the

EXT-1 terminal).

You can choose between an S-VIDEO signal (Y/C signal) and

a regular video signal (composite signal). For details of how

to operate the equipment, see “S-IN (S-VIDEO input)” on

page 26.

Preparation:

• A device (such as DVD player) with a digital output terminal

(coaxial or optical) for Dolby Digital is necessary.

T-V LINK compatible VCR

Be sure to connect the T-V LINK compatible VCR to the

EXT-2 terminal. If not, the T-V LINK function will not work

properly.

• A coaxial cable or optical cable is necessary to make the

connections. (Not supplied with the TV)

• In accordance with the instruction manual which is supplied

with the device, correctly connect a coaxial cable or optical

cable to the device’s DIGITAL OUT (digital output) terminal

and set the device so that the Dolby Digital audio signal is

output.

• When connecting a T-V LINK compatible VCR to the

EXT-2 terminal, be sure to connect the decoder to the

VCR. If not, the T-V LINK function may not work properly.

After you have stored TV channels in the programme

numbers (PR) list, set the DECODER (EXT-2) function for

the programme number (PR) to ON to unscramble a

scrambled TV channel. For details, see “Using the

DECODER (EXT-2) function” on page 35.

• Correctly connect the device to the EXT terminal in

accordance with “Connecting external equipment” on

page 37. However, since the EXT-4 terminal does not work

with Dolby Digital audio, it cannot be used.

Connecting headphones

Connect the headphones with a stereo mini-jack (3.5mm

diameter) to the headphone jack at the TV front panel.

1 Connect the device to the DIGITAL AUDIO

IN terminal with a coaxial cable 1 or

optical cable 2

Video or sound signal output from

the EXT-2 terminal

You can change over the output of the video/sound signal

from the EXT-2 terminal. This is useful when you want to dub

the video/sound from another device onto the VCR connected

to the EXT-2 terminal. For details on how to do this, see

“DUBBING” on page 27.

COAXIAL

DIGITAL

AUDIO IN

OPTICAL

Back of the TV

TV output from the EXT-1 terminal

Connect the device and set the EXT terminal

to DIGITAL-IN in accordance with “DIGITAL-

IN (Only AV32P10EK and AV32P10EI)” on

page 26

The video/sound signal of a TV channel you are viewing is

always output from the EXT-1 terminal.

• Changing over a programme number (PR) also changes

over the TV output from the EXT-1 terminal.

This completes the preparation.

• When an optical input and coaxial input are input

simultaneously, the optical input takes precedence.

• When the headphones are used, the sound

becomes normal stereo.

• The video/sound signal from an EXT terminal cannot be

output.

• Teletext programmes cannot be output.

• This TV does not work with digital audio signals

other than Dolby Digital audio. If no sound is emitted

from the speakers, cancel the DIGITAL-IN setting

and change to normal analog sound.

• The sound from the EXT terminal set to DIGITAL-IN

is not output from the EXT-2 terminal.

Further preparation

I Using additional audio

equipment

After correctly connecting the audio equipment to the TV, use

the TV menu to correctly set the functions of the audio

equipment.

AUDIO OUT

1 Connect the audio equipment to the TV.

Before connecting anything:

• Read the manuals that came with the audio equipment.

Back of the TV

• Do not turn the power of the TV or audio equipment on

until the connections have been completed.

• If the additional speakers are placed immediately next

to the TV, use magnetic-shielded speakers in order to

prevent magnetism from the speakers adversely

affecting the TV.

• Connecting cables are not supplied.

• The sound from the external front speakers L/R and

the subwoofer cannot be stopped even if you set the

TV SPEAKER function in the HEADPHONE menu to

OFF and connect the headphones to the TV. If you

want to stop the sound from the external front

speakers L/R and the subwoofer, please turn off all

amplifiers connected to the TV.

SUB

WOOFER

AUDIO OUT

Surround speakers 1 (Only AV32P10EK and

AV32P10EI):

Connect surround speakers to the TV when you want to

use the DOLBY DIGITAL function to enjoy surround

sound.

SURROUND

REAR

• Even without surround speakers, you can easily enjoy

surround sound by using the 3D-PHONIC function.

• Use impedance 8-ohm type.

Back of the TV

• Pay attention to the positive (+) and negative (-)

polarities when connecting surround speakers to your

TV.

• For the best effect, position the surround speakers at

least 1 metre above the heads of seated viewers.

Front speaker system

(Front L/R speakers 2 and amplifier 3):

You can use your hi-fi audio system speakers instead of

the TV speakers.

Subwoofer system

(Subwoofer and amplifier

5) (Only AV32P10EK

and AV32P10EI):

Using the subwoofer system improves the playing

performance of low sounds.

• It is particularly effective with the low frequency effects

(LFE) included in 5.1-channel Dolby Digital surround

sound.

Approx.

45 degrees

Positioning of speakers

Further preparation

Do you use the subwoofer system?

(Only AV32P10EK and AV32P10EI)

2 Set the following functions (A to D)

correctly depending on the speakers you

want to use

A: SPEAKER function

Stop the sound from being emitted from the TV

speakers.

Yes

OFF

Correctly perform the settings in accordance with

“SPEAKER” on page 21.

Do you use the surround speakers?

(Only AV32P10EK and AV32P10EI)

B: TV SPEAKER function (Only AV32P10EK

and AV32P10EI)

When using the 3D-PHONIC function or DOLBY

DIGITAL function, all the TV speakers work as centre

speakers.

Yes

OFF

Correctly perform the settings in accordance with

“3D-PHONIC setting” on page 24 and “DOLBY DIGITAL

setting” on page 24.

• By using the 5 buttons on the TV remote control

or the buttons on the TV, the volume of all the

speakers including those of the additional audio

equipments can be adjusted together.

• Note that the function explained here is different to the

TV SPEAKER function in the HEADPHONE menu.

• If the volume of the TV speakers is different to the

volume of the front speaker system or subwoofer

system, adjust the volume of each amplifier to match

that of the TV speakers.

• When the TV SPEAKER function in either one of the

3D-PHONIC menu or DOLBY DIGITAL menu is set,

the other is automatically set.

C: SUBWOOFER function (Only AV32P10EK

and AV32P10EI)

When using the 3D-PHONIC function or the DOLBY

DIGITAL function, the SUBWOOFER function makes

the low freaqueney effects (LFE) included in 5.1-channel

Dolby Digital surround sound more effective.

Correctly perform the settings in accordance with

“SUBWOOFER (Only AV32P10EK and AV32P10EI)” on

page 22, “3D-PHONIC setting” on page 24 and “DOLBY

DIGITAL setting” on page 24.

• When the SUBWOOFER function in any one of the

SOUND SETTING menu, 3D-PHONIC menu or

DOLBY DIGITAL menu is set, the others are

automatically set.

• If you set TV SPEAKER (B) to CENTRE or OFF, the

sound from the subwoofer can be heard only when

listening to the Dolby Digital sound with the Low

Frequency effect (LFE).

If you want to hear sound from the subwoofer every

time, set TV SPEAKER to L/C/R.

D: REAR SPEAKER function (Only AV32P10EK

and AV32P10EI)

When the DOLBY DIGITAL function is used Dolby

Digital programme surround sound is emitted from the

surround speakers.

Correctly perform the settings in accordance with

“DOLBY DIGITAL setting” on page 24.

• Note that you cannot use the DOLBY DIGITAL function

to enjoy surround sound if the REAR SPEAKER

function is turned OFF.

Do you use the front speaker system?

(Only AV32P10EK and

AV32P10EI)

Yes

OFF

CENTRE

L/C/R

• In cases where you do not want to hear sound from the

TV speakers set B (TV SPEAKER) to OFF.

TV buttons and parts

I Front panel

EXT-2

EXT-3

EXT-1

1 Remote control sensor and ECO sensor

2 Power lamp

6 r(Volume) button

7 EXT-4 terminal

page 10

pages 5 and 8

pages 26 and 37

3 Main power button

8 3D lamp (Only AV32P10EK and AV32P10EI)

The 3D lamp lights while the 3D-PHONIC function is in use.

•

4 Headphone jack (mini jack)

page 22 and 37

page 10

9 ECO lamp (Only AV32P10EK and AV32P10EI)

• If you set the ECO MODE function to ON, the ECO lamp

lights.

^{5 P}∨^/∧ ^{buttons / –/+ buttons}

0 SLEEP TIMER lamp (Only AV32P10EK and AV32P10EI)

• The SLEEP TIMER lamp lights while the SLEEP TIMER

function is operating.

I Rear Panel

COAXIAL

DIGITAL

AUDIO IN

OPTICAL

SUB

WOOFER

AUDIO OUT

EXT-2

EXT-3

EXT-2

EXT-3

EXT-1

AUDIO OUT

EXT-1

SURROUND

REAR

- Aerial socket

page 4

@ AUDIO OUT terminal

page 39

= EXT-1 terminal

pages 4, 26 and 37

# SURROUND REAR terminal

(Only AV32P10EK and AV32P10EI)

page 39

page 38

~ EXT-2 terminal

pages 4, 7, 26 and 37

pages 26 and 37

$ DIGITAL AUDIO IN terminal

(Only AV32P10EK and AV32P10EI)

! EXT-3 terminal

Troubleshooting

If a problem arises while you are using the TV, please read this troubleshooting guide carefully before you ask to have the TV

repaired. You may be able to fix it easily by yourself. For example, if the mains plug is disconnected from the mains outlet, or the

TV aerial has problems, you may think there is a problem with the TV itself.

Important:

• This troubleshooting guide only covers problems whose causes are not easy to decide. If you have a question when you are

operating a function, read the page(s) for that function carefully, not this troubleshooting guide.

• If you follow the advice in this troubleshooting guide without any success, unplug the mains plug and ask for your TV to be

repaired. Do not attempt to repair the TV by yourself or to remove the rear cover of the TV.

If you cannot turn on the TV

Poor sound

• Have you adjusted BASS or TREBLE properly? If not, follow

• Is the mains plug connected to the mains outlet?

• Is the power lamp lit? If not, press the main power button.

the description “Sound adjustment” on page 21.

• When TV channel reception is poor, it can be hard to hear

the stereo or bilingual sound. In this case, follow the

description “STEREO / I•II” on page 21 to hear the sound

more easily by changing it to a mono sound.

No picture or no sound

• Have you chosen a TV channel with very poor reception? If

so, the BLUE BACK function will be activated: the entire

screen becomes blue, and the sound is muted. If you still

want to view the TV channel, follow the description “BLUE

BACK” on page 28 to try to change the BLUE BACK function

setting to OFF.

If the TV does not respond to the

remote control.

• Have the batteries of the remote control worn out? Follow

the description “Putting batteries into the remote control” on

page 4 and replace them with new batteries.

• Have you set the speaker function to OFF? Follow the

description “SPEAKER” on page 21 to check the speaker

function setting.

• Have you attempted to use the remote control from the sides

or rear of the TV or from more than seven metres away from

the TV? Use the remote control in the front of your TV or

from less than seven metres away.

Poor picture

• If noise (snow) totally blocks out the picture, there may be a

problem with the aerial or aerial cable. Check the following

to try to solve the problem:

• When you want to change the volume of the headphones,

follow the description “HEADPHONE” on page 22.

• When you are viewing a teletext programme, you cannot

operate the menus. Press the

ordinary TV programme, and then try operating the menus.

− Have the TV and aerial been connected properly?

− Has the aerial cable been damaged?

− Is the aerial pointing in the right direction?

− Is the aerial itself faulty?

button to return to the

• If the TV will not respond suddenly, press the main power

button on the TV and turn off the main power. Press the

main power button again to turn on the TV. If the TV returns

to a normal state, it is not a failure.

• If the TV or aerial suffers interference from other equipment,

stripes or noise may appear in the picture. Move any

equipment such as an amplifier, personal computer, or a

hair drier, that can cause interference away from your TV.

Or try moving the TV. If the aerial suffers interference from

a radio tower or high-voltage wire, please contact your local

dealer.

Other issues

• When the SLEEP TIMER function operates, the TV is

automatically turned off. If the TV is turned off suddenly, try

to press the

(standby) button to turn on the TV once

again. If the TV goes back to normal, there is no problem.

• If the TV suffers interference from signals reflecting from

mountains or buildings, double-pictures (ghosting) will

occur. Try to change the aerial’s direction or replace it with

one with better directionality.

•

When a wide screen signal (WSS) is included in the broadcast

signal or the signal from an external device, or when the TV is

receiving a control signal from an external device, the ZOOM

mode will change automatically. When you want to return to

• Are your COLOUR SYSTEM settings correct? Follow the

description “COLOUR SYSTEM” on page 20 to try a way to

solve the trouble.

the previous ZOOM mode, press the

button to choose the ZOOM mode again.

• If you bring a magnetised device such as a speaker near to

your TV, the picture may be warped or unnatural colors may

appear at the corners of the screen. In this case, keep the

device from your TV. If speakers cause this to happen, use

magnetic-shielded speakers instead.

• Have the COLOUR and BRIGHT settings been adjusted

properly? Follow the description “Picture adjustment” on

page 18 to try to adjust them properly.

• Videotaping teletext is not recommended because it may

not record correctly.

• A picture may be tilted due to the earth’s own magnetic field.

If so, use the “PICTURE TILT” on page 20 to correct the tilt.

• When a white and bright still image (such as a white dress)

is displayed on the screen, the white part may look as if it is

coloured. This is unavoidable due to the nature of the picture

tube itself, and not due to a TV failure. When the picture

disappears from the screen, the unnatural colours will also

disappear.

• It takes a short time from the time an operation such as

changing channels is performed until an image is displayed.

This is not a malfunction. This is the time it takes for the

image to stabilize before it can be displayed.

• The TV may make a crackling sound due to a sudden

change in temperature. The picture or sound may be

normal. If you hear crackling sounds frequently while you

are viewing the TV, there may be other causes. As a

precaution, ask your service technician to inspect it.

• When viewing images from commercially available video

software products, or videos from videotapes which have

been recorded improperly, the top of the image may be

distorted. This is due to the condition of the video signal, and

not because of malfunction.

•

Touching the screen may cause you to feel a slight electric

shock due to its static electricity. This is unavoidable due to the

construction of the picture tube. It is not a problem with the TV.

You can rest assured that this static discharge is not harmful.

Specifications

Model

AV32P10EK* (UK model)

AV32P10EI* (Ireland model)

Item

Broadcasting systems

Colour systems

CCIR I

PAL

•

The EXT terminals also support the NTSC 3.58/4.43 MHz system.

Channels and frequencies

E21-E69

IR A-J, E2-E12, E21-E69, S1-S41, X, Y, Z,

Z+1, Z+2, ITALY A-H, ITALY H+1, ITALY H+2

Sound-multiplex systems

Teletext systems

Power requirements

Power consumption

Picture tube size

Audio output

NICAM (I) system

FLOF (Fastext), WST (World Standard Text)

220 - 240 V AC, 50 Hz

Maximum: 293 W, Average: 153 W, Standby: 2.8 W

Viewable area 76 cm (measured diagonally)

Rated Power output: 20 W + 20 W + 5 W

Speakers

10 cm round × 2, 3.5 cm round × 2, (10 cm × 3 cm) oval ×1

Euroconnector (21-pin, SCART)

EXT-1 terminal

•

Video input, Audio L/R inputs and RGB inputs are available.

TV broadcast outputs (Video and Audio L/R) are available.

EXT-2 terminal

Euroconnector (21-pin, SCART)

•

Video input, S-VIDEO (Y/C) input, Audio L/R inputs and RGB inputs are available.

Video and Audio L/R outputs are available.

T-V LINK functions are available.

EXT-3 terminal

EXT-4 terminal

Euroconnector (21-pin, SCART)

Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.

•

RCA connectors × 3

S-VIDEO connector × 1

•

Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.

AUDIO OUT terminal

RCA connectors × 3

•

Variable audio L/R outputs and subwoofer output are available.

Variable out 0-1 Vrms, low impedance

SURROUND REAR terminal Speaker terminals for external for surround speakers.

•

Surround rear sounds are output to the speakers.

•

For impedance 8-ohm speakers only.

Rated power output: 7.5 W + 7.5 W

DIGITAL AUDIO IN terminal Coaxial connector × 1

Optical connector × 1

•

Dolby Digital is available.

Headphone jack

Dimensions (W × H × D)

Weight

Stereo mini-jack (3.5 mm in diameter)

855 mm × 550 mm × 568 mm

57 kg

Accessories

Remote control unit × 1 (RM-C57)

AAA/R03 dry cell battery × 2

* A basic model number. The actual model number may have characters added (such as “S” denoting silver) indicating the colour

of the TV set.

We may change the design and specifications without notice.

Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any commercial or demonstration

purpose in public places (cafes, hotels, etc.) without the consent of the owners of copyright of the original picture sources, as

this would be an infringement of copyright.

Iiyama Computer Monitor B2403WS User Manual
KitchenAid KECC568MBB00 User Manual
MicroBoards Technology QD MultiDrive User Manual
Miele H 394 User Manual
Miele KM83 2 User Manual
Motorola MD7250 User Manual
Panasonic TC 21T1Z User Manual
Philips 32PT7OO5D User Manual
Philips 46PFL5606H User Manual
Philips 215I2 User Manual