JVC AV28R25EK User Manual

Specifications

Model

AV32R25EK*/AV32R250EK*

AV28R250EK*

AV28R25EK*/

Item

Broadcasting systems

Colour systems

CCIR I

PAL

• The EXT terminals also support the NTSC 3.58/4.43 MHz system.

Channels and frequencies E21-E69

Sound-multiplex systems NICAM (I) system

Colour Television

AV32R25EK

AV28R25EK

AV32R250EK

AV28R250EK

Teletext systems

FLOF (Fastext), WST (World Standard Text)

Power requirements

Power consumption

220 - 240 V AC, 50 Hz

Maximum: 200 W, Average: 127 W,

Standby: 3 W

Maximum: 200 W, Average: 125 W,

Standby: 3 W

Picture tube size

Viewable area 76 cm (measured

diagonally)

Viewable area 66 cm (measured

diagonally)

Contents

Audio output

Speakers

Rated Power output: 10 W + 10 W + 10 W, 18 W (woofer)

(13 cm × 6.5 cm) oval × 2, (16 cm × 4 cm) oval × 1, 13 cm round woofer ×1

Setting up your TV. . . . . . . . . . . . . . . . . 5

TV buttons and functions. . . . . . . . . . . 10

Remote control buttons and functions . . .11

Teletext function . . . . . . . . . . . . . . . . . 16

Using the TV’s menu . . . . . . . . . . . . . . 18

Additional menu operations. . . . . . . . . 35

Additional preparation . . . . . . . . . . . . . 39

Troubleshooting. . . . . . . . . . . . . . . . . . 42

Specifications . . . . . . . . . . . . Back cover

EXT-1 terminal

Euroconnector (21-pin, SCART)

• Video input, Audio L/R inputs and RGB inputs are available.

• TV broadcast outputs (Video and Audio L/R) are available.

EXT-2 terminal

Euroconnector (21-pin, SCART)

• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.

• Video and Audio L/R outputs are available.

• T-V LINK functions are available.

EXT-3 terminal

EXT-4 terminal

Euroconnector (21-pin, SCART)

• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.

RCA connectors × 3

S-VIDEO connector × 1

• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.

AUDIO OUT terminal

RCA connectors × 2

• Variable audio L/R outputs are available.

• Variable out 0-1 Vrms, low impedance.

SURROUND REAR

terminal

SPEAKER terminals for external surround speakers.

• Surround rear sounds are output to the speakers.

• For impedance 8-ohm speakers only.

• Rated power output: 7.5 W + 7.5 W

Headphone jack

Stereo mini-jack (3.5 mm in diameter)

Dimensions (W × H × D) 946 mm × 562 mm × 551 mm

854 mm × 507.5 mm × 493.5 mm

Weight

56.0 kg

43.0 kg

Accessories

Remote control unit × 1 (RM-C60 (Gray) or RM-C52 (Brack) is supplied.)

AAA/R03 dry cell battery × 2

*: A basic model number. The actual model number may have characters added (such as “S” for silver)

showing the colour of the TV set.

INSTRUCTIONS

We may change the design and specifications without notice.

Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any

commercial or demonstration purpose in public places (cafes, hotels, etc.) without the consent of the

owners of copyright of the original picture sources, as this would be an infringement of copyright.

LCT1152-001D-U

0403-T-CR-JMUK

Thank you for buying this JVC colour television.

To make sure you understand how to use your new TV, please read this manual thoroughly before you

begin.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

• Operate only from the power source specified

(AC 220 – 240 V, 50 Hz) on the unit.

• Avoid damaging the AC plug and power cord.

• When you are not using this unit for a long

period of time, it is recommended that you

disconnect the power cord from the main

outlet.

• The main power button on the TV does not

fully isolate the TV from the mains supply. If

you are not going to use this TV for a long

period of time, be sure to disconnect the mains

plug from the mains outlet.

Avoid improper installation and never position the unit where good

ventilation is unattainable.

When installing this TV, distance recommendations must be

maintained between the floor and wall, as well as installation in a tightly

enclosed area or piece of furniture.

Adhere to the minimum distance guidelines shown for safe operation.

Failure to heed the following precautions may result in damage to the TV or

remote control.

DO NOT block the TV’s ventilation openings or holes.

(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be

able to get out.)

DO NOT place anything on top of the TV.

(such as cosmetics or medicines, flower vases, potted plants, cups, etc.)

DO NOT allow objects or liquid into the cabinet openings.

(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)

DO NOT place any naked flame sources, such as lighted candles, on the TV.

The surface of the TV screen is easily damaged. Be very careful with it when handling the TV.

Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully.

Never use any cleaner or detergent on it.

In the event of a fault, unplug the unit and call a service technician. Do not attempt to repair it

yourself or remove the rear cover.

„

Warning

DO NOT cut off the mains plug from this

equipment. If the plug fitted is not suitable

for the power points in your home or the

cable is too short to reach a power point, then

obtain an appropriate safety approved

extension lead or adaptor or consult your

dealer.

As these colours may not correspond with the

coloured marking identifying the terminals in

your plug proceed as follows:

The wire which is coloured blue must be

connected to the terminal which is marked

with the letter N or coloured black.

The wire which is coloured brown must be

connected to the terminal which is marked

with the letter L or coloured red.

If nonetheless the mains plug is cut off,

remove the fuse and dispose of the plug

immediately, to avoid a possible shock

hazard by inadvertent connection to the

mains supply.

When replacing the fuse only a correctly

rated approved type should be used and be

sure to re-fit the fuse cover.

If a new mains plug has to be fitted, then

follow the instruction given below:

„ If in doubt — consult a competent

electrician.

Important

Do not make any connection to the larger

terminal which is marked with the letter E or

How to replace the fuse

Open the fuse

compartment with a

by the safety earth symbol

green or green-and-yellow.

or coloured

blade screwdriver, and

replace the fuse.

The wires in the mains lead on this product

are coloured in accordance with the

following code:

Fuse

Blue: Neutral

Brown: Live

„

Guidelines for safe operation

This equipment has been designed and manufactured to comply with international safety

standards. However, as with any electrical appliance, care must be taken to ensure optimal results

and operational safety.

• Before attempting to use this equipment, read the operating instructions thoroughly.

• Ensure that all electrical connections (including the mains plug, extension leads, etc.) have

been made in accordance with the manufacturer’s instructions.

• If ever in doubt about the installation, operation or safety of this equipment, consult your

dealer.

• Handle all glass panels or covers with care.

• Never operate this equipment if it appears damaged or operates abnormally. Turn the power

off, disconnect the main power plug and consult your dealer.

• Never remove any affixed panels or covers. Doing so may result in electrical shock.

• Never leave this equipment operating unattended unless otherwise specifically stated that it is

designed to do so or in standby mode. Only use the designated power switch to turn off the

power and ensure that all potential users are instructed how to do so. Make special

arrangements for infirm or handicapped persons.

• Never watch TV while operating a motor vehicle. It is illegal to watch TV while driving.

• Never listen to headphones at high volume. Doing so may damage your hearing.

• Never obstruct the ventilation of this equipment. Doing so may cause overheating and result in

a malfunction or damage.

• Never use makeshift stands or attempt to affix legs with wood screws. When using a

manufacturer’s approved stand or legs, use only the fixtures provided and follow the

installation instructions.

• Never allow this equipment to be exposed to rain or moisture.

• Never allow anyone, especially children, to insert anything into an opening in the case. Doing

so may result in a fatal electrical shock.

• Never guess or take chances with electrical equipment of any kind. It is better to be safe than

sorry.

Caution

• The woofer unit is mounted on the TV. Always move the TV and woofer unit together when

removing the TV from the box, or when moving the woofer unit.

• If the TV is tilted during movement the woofer unit may fall. Be careful to keep the TV level

when moving it.

• Do not grip the woofer unit when moving the TV.

• Do not place objects on the woofer unit duct.

Setting up your TV

Caution

• Turn off all the equipment including the TV before connecting anything.

Connecting the aerial and video cassette recorder (VCR)

• The connecting cables are not provided.

• For further details, refer to the manuals provided with the devices to be connected.

„ If you are connecting a VCR,

follow A → B → C → D in the

diagram opposite.

Mains outlet

Aerial

(AC 220 - 240

V, 50 Hz)

Back of the TV

„ If you are not connecting a VCR,

UHF

aerial

follow 1 → 2.

To use the T-V LINK functions, you must

WOOFER

EXT-2

EXT-3

have a T-V LINK compatible VCR

connected by a SCART cable C to the EXT-

2 terminal on the TV. For details about T-V

LINK functions, see “T-V LINK functions”

on page 8.

)

SURROUND

REAR

EXT-1

power Cord

WOOFER

75-ohm

Coaxial

Cable

AUDIO OUT

EXT-2

EXT-3

• You can watch a video using the VCR

without doing C. For details, see your

VCR instruction manual.

• To connect more equipment, please see

“Additional preparation” on page 39.

• To connect external speakers and an audio

system, please see “Connecting speakers

or an amplifier” on page 40.

)

EXT-1

SURROUND

REAR

aerial

plug

21-pin

SCART

Cable

75-ohm

Coaxial

Cable

aerial

plug

To Aerial

Input

VCR

• If you connect a decoder to a T-V LINK

compatible VCR, set the DECODER

(EXT-2) function to ON. For details, see

“Using the DECODER (EXT-2)

function” on page 35.

aerial

plug

To Aerial

Output

AV IN/OUT

Terminal

Otherwise, you will not be able to watch

scrambled channels.

„ Rear Panel

1 WOOFER terminal (page 39)

2 AUDIO OUT terminal (page 40)

3 SURROUND REAR terminal (page 39)

4 EXT-1 terminal (pages 5, 25, 39)

5 EXT-2 terminal (pages 5, 8, 25, 39)

6 EXT-3 terminal (pages 25, 39)

7 Aerial socket (page 5)

WOOFER

AUDIO OUT

EXT-2

EXT-3

)

EXT-1

SURROUND

REAR

Setting up your TV

Putting the batteries into the

Remote control

Initial settings

When the TV is first turned on, it goes into

the initial setting mode, and you will see the

JVC logo. Follow the instructions on the

screen display to make the initial settings.

Use two AAA/R03 dry cell batteries.

Insert the batteries from the - end, making

sure the + and - polarities are correct.

Blue button

• Follow the warnings printed on the

batteries.

• Battery life is about six months to one

year, depending on how much you use the

remote control.

• The batteries we supply are only for

setting up and testing your TV, please

replace them as soon as you need to.

• If the remote control does not work

properly, replace the batteries.

1 Press the Main power button on the

The Power lamp lights red (for power on),

then green (for TV on) and the JVC logo

appears.

Power lamp

Main power

button

• If the power lamp stays red and does not

change to green:

your TV is in the standby mode. Press the

# (standby) button on the remote

control to turn your TV on.

• If the JVC logo does not appear this is

because your TV has already been turned

on for the first time:

use the “LANGUAGE” and “AUTO

PROGRAM” functions to make the initial

settings. For details, see “INSTALL” on

page 29.

Setting up your TV

2 Press the a button

5 Press the a button to display the

T-V LINK menu

The LANGUAGE menu appears.

6 If you do not have a T-V LINK

compatible VCR connected:

Press the b button to exit the T-V LINK

menu.

3 Press the 6 buttons to choose

ENGLISH

The on-screen display will then be in

English.

The T-V LINK menu disappears.

To receive SKY 1 you need a satellite

tuner. You must have the satellite tuner

set to SKY 1 before starting the AUTO

PROGRAM function which follows.

If you have a T-V LINK compatible

VCR connected to the EXT-2

terminal:

Follow the operating procedure

“Downloading data to a VCR” on page 35

to transmit the programme number (PR)

data.

4 Press the a button to start the

AUTO PROGRAM function

The AUTO PROGRAM menu appears

and received TV channels are

automatically stored in the programme

numbers (PR).

• To cancel the AUTO PROGRAM

function:

Press the b button.

After the TV channels have been

registered in the programme

numbers (PR), the EDIT menu

appears

• If you want to, you can now edit the

programme numbers (PR) using the

EDIT/MANUAL function. For details,

see “EDIT/MANUAL” on page 30.

• If you do not want to edit programme

numbers (PR), go to the next step.

Setting up your TV

Now, the initial settings are complete,

and you can watch the TV

T-V LINK functions

• BBC1, BBC2, ITV, Channel 4 and

Channel 5 are automatically set to

programme numbers PR 1 to PR 5. SKY 1

is set to programme number PR 6, but no

TV channel name (ID) is set. If the TV

doesn’t receive one of these TV channels,

that programme number (PR) will not be

set.

• If a TV channel you want to view is not

set to a programme number (PR), you can

set it using the MANUAL function. For

details, see “EDIT/MANUAL” on

page 30.

• The AUTO PROGRAM function does not

set the programme number PR 0 (AV) for

your video cassette recorder. You will

need to set this using the MANUAL

function.

• In some areas you may get TV reception

from more than one transmitter, for

example different ITV regions. In this

case each TV channel could be set twice.

If this happens, the first set of channels

will have the stronger signal. If you want

to delete the second set of channels, you

will have to do it manually (see page 33).

When you have a T-V LINK compatible

VCR connected to the EXT-2 Terminal on

the TV, it is easier to set up the VCR and to

view videos. T-V LINK uses the following

features:

To use T-V LINK functions:

A “T-V LINK compatible VCR” means a

JVC video cassette recorder with the T-V

LINK logo, or with one of the following

logos. However, these VCRs may support

some or all of the features described earlier.

For details, see your VCR instruction

manual.

“Q-LINK” (a trademark of Panasonic

Corporation)

“Data Logic” (a trademark of Metz

Corporation)

“Easy Link” (a trademark of Phillips

Corporation)

“Megalogic” (a trademark of Grundig

Corporation)

“SMARTLINK” (a trademark of Sony

Corporation).

„ Pre-set download

The VCR will automatically download the

registered data on the TV channels from the

TV. This means you do not need to set up the

program channels on your VCR manually.

The preset download function automatically

begins when the initial setting is complete or

whenever you carry out the AUTO

PROGRAM or EDIT/MANUAL functions.

You can also carry out this function using

your VCR controls.

When “FEATURE NOT AVAILABLE” is

displayed:

If “FEATURE NOT AVAILABLE” is

displayed, the download was not performed

correctly. Before trying to download again,

check that:

• the VCR power is turned on

• the VCR is T-V LINK compatible

• the VCR is connected to the EXT-2

terminal

• the SCART cable is fully wired.

Setting up your TV

„ Direct Rec

“What You See Is What You Record”

You can easily record to VCR the images

that you are watching on the TV.

For details, read the manual for your VCR.

Use your VCR controls. “VCR IS

RECORDING” is displayed.

In the following situations, the VCR

will stop recording if the TV is turned

off, if the TV channel or input is

changed, or if the menu is displayed

on the TV:

• when recording images from an external

device connected to the TV (for example

a camcorder)

• when recording a TV channel after it has

been unscrambled on a decoder

• when recording a TV channel by using the

TV’s output because the VCR’s own

tuner cannot properly receive that

channel.

You cannot carry out Direct Rec using your

TV’s control.

Generally, the VCR cannot record a TV

channel that it cannot receive properly on its

own tuner, even if you can view that TV

channel on the TV. However, some VCRs

can record a TV channel by using the TV’s

output if that channel can be viewed on the

TV. For details, see your VCR instruction

manual.

„ TV auto power on/VCR image view

When the VCR starts playing, the TV

automatically turns on and the images from

the EXT-2 terminal appear on the screen.

When the VCR menu is operated, the TV

automatically turns on and the images from

the EXT-2 terminal appear on the screen.

• This function does not happen if your

TV’s main power is turned off. Set your

TV’s main power to on (standby mode).

TV buttons and functions

Refer to the pages in brackets for details.

1 Remote control sensor

2 Power lamp (6, 10)

3 Main power button (6, 10)

4 Headphone jack (mini jack) (39)

5 P p buttons/ q buttons (11)

6 r (Volume) button (10)

7 EXT-4 terminal (25, 39)

Turn the main power on

Press the Main power button on the

TV.

The power lamp lights red and your TV is in

the standby mode.

• If the power lamp lights green, the TV is

already on.

To turn the main power off:

Press the main power button again.

The power lamp goes off.

WOOFER

EXT-2

EXT-3

)

SURROUND

REAR

EXT-1

Caution

• The main power button on the TV does

not fully isolate the TV from the AC

supply. If you are not going to use the TV

for a long period of time, be sure to

disconnect the AC plug from the AC

socket.

Turn the TV on from standby

mode

Press the P p buttons to turn the TV

on from standby mode

Choose a TV channel

Press the P p buttons to choose a

programme number (PR) or an EXT

terminal

Adjust the volume

1 Press the r (Volume) button

The volume level indicator appears.

2 Press the q buttons while the

volume level indicator is on screen

Remote control buttons and functions

1 Muting button

2 Number buttons

3 ZOOM button

4 3D button

5 Information button

6 TV button

7 5 buttons

8 Standby button

9 Colour buttons

0 a button

- 6 buttons

= VCR/DVD/Teletext control button

~ VCR P DVD switch

g (Text) button

Turn the TV on or off from

standby mode

Press the # (standby) button to turn

the TV on or off.

When the TV is turned on, the power lamp

changes from red to green.

• The power can be turned on by pressing

the b button, 6 buttons or Number

buttons.

Choose a TV channel

„ Use the number buttons:

Enter the programme number (PR)

of the channel using the number

buttons.

Example:

• PR6 → press 6

• PR12 → press 1 and 2

„ Use the 6 buttons:

Press the 6 buttons to choose

the programme number (PR) you

want.

Remote control buttons and functions

„ Use the PR LIST:

„ Muting the sound

Press the (muting) button to

1 Press the

(Information) button to

turn off the sound.

display the PR LIST

Pressing the (information) button

Pressing the (muting) button again

restores the previous volume level.

changes the display as follows:

Watch images from external

equipment

„ Use the o button:

Press the o button to choose

an EXT terminal.

TV mode

EXT modes

Programme

numbers

PR 1 – PR 99

EXT-1

EXT-2

EXT-3

Current time

No display

EXT-4

„ Use the 6 buttons:

2 Press the 5 and 6 buttons to

choose a programme number (PR).

Then press the a button

Press the 6 buttons to choose

an EXT terminal.

• For programme numbers (PR) with the

CHILD LOCK function set, the n

(CHILD LOCK) mark appears next to

the Programme number (PR) in the PR

LIST.

„ Use the PR LIST:

1 Press the

(Information) button to

display the PR LIST

• You cannot use the 6 buttons to

choose a programme number (PR)

with the CHILD LOCK set.

• Even if you try to choose a programme

number (PR) with the CHILD LOCK

set, the n (CHILD LOCK) mark will

appear, and you cannot watch the TV

channel. To watch the TV channel, see

“CHILD LOCK” on page 28.

2 Press the 5 and 6 buttons to

choose an EXT terminal. Then

press the a button

• For programme numbers (PR) where

you have the CHILD LOCK function

set, the n (CHILD LOCK) mark

appears next to the programme number

(PR) in the PR LIST.

• You cannot use the 6 buttons to

choose a Programme number (PR)

which has the CHILD LOCK set.

• Even if you try to choose a programme

number (PR) with the CHILD LOCK

set, the n mark will appear, and you

cannot watch the TV channel. To

watch the TV channel, see “CHILD

LOCK” on page 28.

• If the picture is tilted, correct it. See

“PICTURE TILT (not AV28R25EK/

AV28R250EK)” on page 21.

Adjust the volume

Press the 5 buttons to adjust the

volume.

The volume indicator appears and the

volume changes as you press the q

buttons.

• If the picture is tilted, correct it. See

“PICTURE TILT (not AV28R25EK/

AV28R250EK)” on page 21.

Remote control buttons and functions

To return to a TV channel:

Press the b button, the 6 buttons or the

number buttons.

• This TV supports WSS (wide-screen

signals). When broadcasts with WSS are

received with the ZOOM mode set at

AUTO (WSS), the most suitable ZOOM

mode is automatically chosen according

to the WSS received.

To use the programme number PR 0

(AV):

When the TV and VCR are connected only

by the aerial cable, choosing the programme

number PR 0 (AV) allows you to view

images from the VCR. Set the VCR RF

channel to the programme number PR 0

(AV) manually. For details, see “EDIT/

MANUAL” on page 30.

REGULAR:

Use to view a normal picture (4:3 aspect

ratio) as this is its original shape.

Pressing the o button changes the

choice as follows:

PANORAMIC:

This stretches the left and right sides of a

normal picture (4:3 aspect ratio) to fill the

screen, without making the picture appear

unnatural.

EXT modes

TV mode

PR 0

numbers

PR 1 – PR 99

EXT-1

EXT-2

Programme

EXT-4

EXT-3

• The top and bottom of the picture are

slightly cut off.

• The VCR sends its playback image along

the aerial cable as an RF (radio frequency)

signal.

14:9 ZOOM:

This zooms up the wide picture (14:9 aspect

ratio) to the upper and lower limits of the

screen.

• Also see your VCR instruction manual.

ZOOM function

You can change the screen size according to

the picture aspect ratio. Choose the optimum

one from the following ZOOM modes.

16:9 ZOOM:

This zooms up the wide picture (16:9 aspect

ratio) to the full screen.

AUTO (WSS):

For any picture format except normal picture

(4:3 aspect ratio), the picture will be

automatically displayed in the ideal screen

size.

16:9 ZOOM SUBTITLE:

This zooms up the wide picture (16:9 aspect

ratio) with subtitles to the full screen.

For normal picture (4:3 Aspect Ratio), you

can choose a ZOOM mode from the 4:3

AUTO ASPECT menu. For details, see “4:3

AUTO ASPECT” on page 21.

• AUTO may not work properly with poor

signal quality. In this case, choose the best

ZOOM mode manually.

Remote control buttons and functions

FULL:

3 While it is displayed, press the 6

buttons to change the height of the

picture

This uniformly stretches the left and right

sides of a normal picture (4:3 aspect ratio) to

fill the wide TV screen.

• You cannot adjust the visible area in

REGULAR or FULL mode.

PRO LOGIC 3D-PHONIC

function

• For 16:9 aspect ratio pictures that have

been squeezed into a normal picture (4:3

aspect ratio), use the FULL mode to

restore the picture to its original shape.

You can turn the PRO LOGIC 3D-PHONIC

function on or off, or you can switch to the

3D HEADPHONE function by one-touch

operation.

„ Choose the ZOOM mode

1 Press the c button to display

the ZOOM menu

Press 3D button.

Pressing 3D button changes the function as

follows:

2 Press the 6 buttons to choose a

ZOOM mode. Then press the a

button

3UHYLRXVꢅVXUURXQGꢅIXQFWLRQ

The picture expands and the chosen

ZOOM mode is displayed in about 5

seconds.

• You can pre-set a ZOOM mode for the

normal picture. See “4:3 AUTO

ASPECT” on page 21.

• If some other surround function is

activated before you press the 3D button,

you can return to that surround function.

• The PRO LOGIC 3D-PHONIC function

will be activated when no headphones are

connected. For details, see “PRO LOGIC

3D-PHONIC (Dolby Pro Logic 3D-

PHONIC)” on page 22.

„ Adjusting the visible area of the

picture

If subtitles or the top (or bottom) of the

picture are cut off, you can adjust the visible

area of the picture manually.

• The 3D HEADPHONE function will be

activated when headphones are

connected. For details, see “3D

HEADPHONE” on page 24.

1 Press the c button

The ZOOM menu appears.

2 Press the a button to display the

ZOOM mode indicator.

The indicator appears.

Remote control buttons and functions

Displaying the current time

Operating a JVC brand VCR or

DVD player

You can display the current time on the

screen.

These buttons will operate a JVC brand VCR

or DVD player. Pressing a button that looks

the same as the device’s original remote

control button has the same effect as the

original remote control.

Press the

(Information) button to

display the current time

Pressing the (Information) button changes

the display as follows:

1 Set the VCR P DVD switch to the

VCR or DVD position.

VCR:

When you are using a VCR, set the switch

to the VCR position.

DVD:

When you are using a DVD player, set the

switch to the DVD position.

P (Text):

When you are viewing Teletext

programmes, set the switch to the

P (Text) position.

Current time

No indication

2 Press the VCR/DVD control button

to control your VCR or DVD player

• If your device is not made by JVC,

these buttons will not work.

• This TV uses teletext data to set the time.

If the TV has not received a TV channel

that has teletext programmes since it was

turned on, the time display is blank. To

see the time, choose a TV channel that has

teletext programmes. The time will still

be displayed as long as you do not turn off

the TV, even if you choose other TV

channels.

• Even if your device is made by JVC,

some of these buttons may not work,

depending on the device you are using.

• You can use the p buttons to choose

a TV channel the VCR will receive, or

choose the chapter the DVD player

plays back.

• When watching videos, an incorrect time

is sometimes displayed.

• Some models of DVD player use the

p buttons for both operating the fast

forward/backward functions and for

choosing the chapter. In this case, the

253 buttons do not work.

Return to TV channel instantly

You can return to a TV channel instantly.

Press the b button

The TV returns to the TV mode and a TV

channel appears.

Teletext function

• If you have trouble receiving teletext

broadcasts, consult your local dealer or

the teletext station.

• In Text mode, the ZOOM mode is

fixed to FULL.

• You cannot operate menus when

viewing a teletext programme.

Using the List Mode

You can store the numbers of your favourite

teletext pages in memory and call them up

quickly using the colour buttons.

Basic operation

To store the page numbers:

You can view two types of teletext

broadcasts on the TV:

FLOF (Fastext) and WST.

1 Press the M button to go into

the List mode

The page numbers you have stored are

displayed at the bottom of the screen.

1 Choose a TV channel with a teletext

broadcast

2 Press a colour button to choose a

position. Then press the number

buttons to enter the page number

2 Set the VCR P DVD switch to the

(Text) position

3 Press g (Text) button to display

the teletext

Pressing g (Text) button changes the

mode as follows:

3 Press and hold down the P

button

The four page numbers blink white to

show that they are stored in memory.

TEXT

---

To call up a stored page:

TV mode

Text mode

1 Press the M button to enter

the List mode

4 Choose a teletext page by pressing

the 6 buttons, number buttons or

colour buttons

2 Press a colour button having a

stored page

To return to the TV mode:

Press the b button or g (Text) button.

To leave the List mode:

Press the M button again.

Teletext function

Hold

Size

You can hold a teletext page on the screen for

You can double the height of the teletext display.

as long as you want, even while several other

teletext pages are being received.

Press the R button.

Press the N button

+ROGꢆLQGLFDWLRQ

To cancel the Hold function:

Press the N button again.

Sub-page

Index

Some teletext pages include sub-pages that

are automatically displayed.

You can hold any sub-page, or view it at any

time.

You can return to the index page instantly.

Press the T button

FLOF (Fastext)/TOP/WST (World

Standard Text):

Returns to page 100 or a previously specified

page.

1 Press the O button to

operate the sub-page function

List mode:

Returns to the page number displayed in the

lower left area of the screen.

2 Press the Number buttons to enter

a sub-page number

Example:

• 3rd sub-page → press o,

o, o and 3.

Cancel

To cancel the sub-page function:

Press the O button again.

• You can also choose a sub-page by

pressing the red or green button.

You can search for a teletext page while

watching TV.

1 Press the number button to enter a

page number, or press a colour

button

Reveal

The TV searches for a teletext page.

Some teletext pages include hidden text

(such as the answers to a quiz).

You can display the hidden text.

2 Press the S button.

The TV programme appears. When the TV

finds the teletext page, its page number

appears in the upper left of the screen.

Each time you press the Q

button, text is hidden or revealed

3 Press the S button to return

to a teletext page when the page

number is on the screen

• The TV mode cannot be resumed by

pressing the S button. To

return to the TV mode press b.

Using the TV’s menu

This TV has a number of functions you can

operate using menus. To use all your TV’s

functions, you need to understand the basic

menu operating techniques fully.

• The display appearing at the bottom of

a menu shows the buttons on the

remote control you can use when you

operate a chosen function.

Blue button

b button

a button

When a menu is displayed on the screen,

the ZOOM mode may be automatically

changed to the FULL mode. This is not a

malfunction. When the menu disappears,

the ZOOM mode will return to the

previously set ZOOM mode.

Basic operation

1 Press the a button to display the

MENU (main menu)

2 Press the 6 buttons to choose a

menu title, and press the a button

The menu appears.

When the headphones are not

connected to the TV:

To return to the previous menu:

Press the

(information) button.

To exit a menu instantly:

Press the b button.

3 Press the 6 buttons to choose a

function

• For details of the functions in the

menus, see the following pages.

When the headphones are

connected to the TV:

4 Press the 5 buttons to choose

the setting of that function

• If you want to operate a function

which appears only with its name,

follow the descriptions of that function

on the following pages.

• The display appearing at the bottom of

a menu shows you the button on the

remote control that you can use when

you operate a chosen function.

• You cannot choose DIGITAL

SURROUND and HEADPHONE

SURROUND on the MENU (main

menu) at the same time. To display

HEADPHONE SURROUND on the

MENU, connect the headphone to the

TV. To display DIGITAL

5 Press the a button to complete

the setting

The menu disappears.

• When watching the television with the

NTSC system, the menus are displayed

at about half of their normal vertical

size.

SURROUND on the MENU,

disconnect the headphone from the TV.

Using the TV’s menu

HUE

PICTURE SETTING

You can adjust the picture tint.

2 : reddish

3 : greenish

• You can change the HUE setting (picture

hue) only when the colour system is

NTSC 3.58 or NTSC 4.43. (See

“Specifications” on the back cover.)

To return to the default settings in

each TINT mode:

Press the blue button.

„ TINT

• This returns the picture settings in the

TINT mode you have chosen to the

default settings, and stores them in the

TINT mode.

You can select one of three TINT modes

(three kinds of picture settings) to adjust the

picture settings automatically.

COOL:

A cool white colour base with a boost in the

colour and contrast levels that creates a more

vivid picture.

WARM:

A warm orange/red colour base that creates

the appropriate colour and contrast levels for

watching films.

NORMAL:

A normal white colour base with normal

colour and contrast levels.

„ Picture Adjustment

You can change the picture settings of each

TINT mode as you like.

CONTRAST

You can adjust the picture contrast.

2 : lower

3 : higher

BRIGHT

You can adjust the picture brightness.

2 : darker

3 : brighter

SHARP

You can adjust the picture sharpness.

2 : softer

3 : sharper

COLOUR

You can adjust the picture colour.

2 : lighter

3 : deeper

Using the TV’s menu

„ COLOUR SYSTEM

PICTURE FEATURES

The colour system is chosen automatically.

However, if the picture is not clear or no

colour appears, choose the colour system

manually.

„ AUTO VNR

VNR Stands for “video noise reduction”.

AUTO:

1 Choose COLOUR SYSTEM then

This mode reduces any “noise” (interference

or snowing) in the current picture. The

function also adjusts the optimum sharpness

of the picture (SHARP).

press the a button

2 Press the 5 buttons to chose the

appropriate colour system.

Then press the a button

MIN:

The AUTO VNR function is cancelled. If

you set the mode to AUTO but feel that the

sharpness of the original picture has not been

reproduced fully, change the mode to MIN.

However, any noise remaining in the original

picture may be emphasized.

PAL:

PAL system

NTSC 3.58:

NTSC 3.58 MHz system

NTSC 4.43:

NTSC 4.43 MHz system

MAX:

AUTO:

This mode always reduces any noise as much

as possible, irrespective of state of the

picture. When you set the mode to AUTO but

still notice some noise, change the mode to

MAX. However, this may reduce the

sharpness of the picture.

This function detects a colour system from

the input signal. You can only use this when

you are viewing a picture from programme

number PR 0 (AV), or EXT terminal.

• The AUTO function may not work

properly if you have poor signal quality.

If the picture is abnormal in the AUTO

function, choose another colour system

manually.

• You cannot choose NTSC 3.58 or NTSC

4.43 for programme number PR 0 (AV) to

PR 99.

Using the TV’s menu

„ 4:3 AUTO ASPECT

SOUND SETTING

You can choose one of three ZOOM modes,

REGULAR, PANORAMIC or 14:9 ZOOM,

as the ZOOM mode for the normal picture

(4:3 aspect ratio).

1 Choose 4:3 AUTO ASPECT then

press the a button

„ STEREO / I • II

When you are viewing a bilingual broadcast

programme, you can choose the sound from

Bilingual I (Sub I) or Bilingual II (Sub II). If

you have poor reception on a stereo

broadcast, you can change from stereo to

mono sound so that you can hear the

broadcast more clearly and easily.

2 Press the 6 buttons to choose a

ZOOM mode

„ PICTURE TILT

s: Stereo sound

(not AV28R25EK/AV28R250EK)

Sometimes the Earth’s own magnetic field

may make the picture tilt. If this happens,

you can correct the picture tilt.

v : mono sound

t : Bilingual I (sub I)

u : Bilingual II (sub II)

1 Choose PICTURE TILT. Then press

• The sound mode you can choose differs

depending on the TV programme.

the a button

• This function does not work in the EXT

modes. And this function does not appear

in the SOUND SETTING menu.

„ Sound Adjustment

You can adjust the sound to your liking.

BASS

You can adjust the low tone of the sound.

2 : weaker

3 : strong

2 Press the 6 buttons until the

picture becomes level. Then press

the a button

TREBLE

You can adjust the high tone of the sound.

2 : weaker

3 : strong

Using the TV’s menu

BALANCE

You can adjust the volume balance between

the left and right speaker.

Digital surround

2 : turn the left speaker’s volume level up.

3 : turn the right speaker’s volume level up.

• When the DOLBY PRO LOGIC

function or PRO LOGIC 3D-PHONIC

function is operating, the

“BALANCE” item does not appears.

„ SPEAKER

You can turn off the sound from the TV

speakers; but you should only do this if you

have connected an audio system to the TV

instead of the TV speakers. When you are

using this function, see “Turning the TV’s

speakers off” on page 36.

• Connecting the headphones to the TV

automatically changes to the

HEADPHONE SURROUND function

which corresponds to the current

DIGITAL SURROUND function.

However, the PRO LOGIC 3D-PHONIC

function and DOLBY PRO LOGIC

function are changed over to the 3D

HEADPHONE function as headphones

cannot play back the Dolby Surround Pro

Logic sound properly.

ON:

The TV speakers issue sound.

OFF:

The TV speakers do not issue sound.

• The 5 buttons of the TV remote

control and the r (volume) buttons at

the front panel of your TV set can be used

to control the volume of each speaker

simultaneously.

„ PRO LOGIC 3D-PHONIC

(Dolby Pro Logic 3D-PHONIC)

The PRO LOGIC 3D-PHONIC function lets

you enjoy the atmosphere of Dolby Surround

Pro Logic sound without needing extra

surround speakers.

• Setting the volume of the amplifier too

high may damage the front speakers.

With the PRO LOGIC 3D-PHONIC

function, you can use the rear surround-

channel signal of the Dolby Surround

encoded programme to create the surround

sound image as if surround speakers were

located at your right and left.

• When the DOLBY PRO LOGIC function

or PRO LOGIC 3D-PHONIC function is

operating, the “SPEAKER” item does not

appears.

Use the PRO LOGIC 3D-PHONIC

function

Choose PRO LOGIC 3D-PHONIC.

Then press the a button

To cancel the PRO LOGIC 3D-

PHONIC function:

Press the 6 buttons to choose

SURROUND OFF.

Using the TV’s menu

• The PRO LOGIC 3D-PHONIC function

does not work properly except for Dolby

Surround encoded programmes.

• You can turn the PRO LOGIC 3D-

PHONIC function on or off by pressing

the 3D button.

3 Press the a button to complete

the setting

• To change the TV speaker setting, you

should connect an audio system to the

TV. For details, see “Connecting

speakers or an amplifier” on page 40.

• When an audio system is not

connected to your TV, please be sure

to leave the TV SPEAKER setting to

L/C/R. If you don’t, a normal sound

will not come from the TV speakers. If

the TV SPEAKER is not set to L/C/R,

press the 6 buttons to choose TV

SPEAKER and press the 5 buttons

to choose L/C/R again.

Change the setting of the PRO LOGIC

3D-PHONIC function

1 Choose PRO LOGIC 3D-PHONIC.

Then press the 3 button

The sub-menu of the PRO LOGIC 3D-

PHONIC function appears.

„ DOLBY PRO LOGIC

You can enjoy Dolby* Surround Pro Logic

sound if you add surround speakers.

Before using the DOLBY PRO LOGIC

function, first connect the surround speakers

to the TV, then set the items in the DOLBY

PRO LOGIC function properly. For details,

see “Connecting speakers or an amplifier” on

page 40.

2 Press the 6 buttons to choose an

item. Then press the 5 buttons

to change the setting

Choose DOLBY PRO LOGIC. Then

press a button

MODE:

The PRO LOGIC 3D-PHONIC function

has three modes; NORMAL, CINEMA/

SPORT, and MUSIC. You can choose

and set a mode as you like.

To cancel the DOLBY PRO LOGIC

function:

Press the 6 buttons to choose

SURROUND OFF.

LEVEL:

• The DOLBY PRO LOGIC function

will not work correctly unless you

connect extra surround speakers.

• The DOLBY PRO LOGIC function is

only available for Dolby Surround

encoded programmes.

You can control the effect level of the

PRO LOGIC 3D-PHONIC function as

you like.

TV SPEAKER:

For details, see “Additional Sound

settings” on page 36.

• Even if you do not have surround

speakers, the PRO LOGIC 3D-

PHONIC function lets you enjoy the

atmosphere of Dolby Surround Pro

Logic sound. For details, see “PRO

LOGIC 3D-PHONIC (Dolby Pro

Logic 3D-PHONIC)” on page 22.

LEFT/CENTRE/RIGHT:

You can adjust the sound level of each

speaker separately. LEFT/RIGHT means

left and right of the front speakers and

CENTRE means the centre speaker.

* Manufactured under license from

Dolby Laboratories. “Dolby”, “Pro

Logic”, and the double-D symbol are

trademarks of Dolby Laboratories.

Using the TV’s menu

„ Other surround functions

You can enjoy enhanced sound with one of

the following four surround functions:

Headphone surround

DANCE CLUB:

This function creates a dance club

atmosphere. It does not work properly for

mono sound.

CONCERT HALL:

This function creates a concert hall

atmosphere. It does not work properly for

mono sound.

Preparation:

STADIUM:

Before using a function in the HEADPHONE

SURROUND menu, please be sure to

connect the headphones to your TV. If the

headphones are not connected to the TV, the

DIGITAL SURROUND function becomes

active instead of the HEADPHONE

SURROUND function.

This function creates a stadium atmosphere.

It does not work properly for mono sound.

HYPER SOUND:

This function enhances mono sound to create

a stereo sound feel. It does not work properly

for stereo sound.

• Disconnecting the headphones from the

TV automatically changes to the

DIGITAL SURROUND function

corresponding to the current

HEADPHONE SURROUND function.

However, the 3D HEADPHONE function

is changed over to either the PRO LOGIC

3D-PHONIC function or DOLBY PRO

LOGIC function, depending on the state

at that time.

To cancel the function:

Press the 6 buttons to choose

SURROUND OFF.

• The above function does not work

properly for Dolby Surround encoded

programmes.

„ 3D HEADPHONE

The 3D HEADPHONE function produces

3D surround effects that are heard through

headphones, but should be more naturally

placed, as if they were coming out of

separate front speakers.

Choose 3D HEADPHONE. Then press

a button

To cancel the 3D HEADPHONE

function:

Press the 6 buttons to choose

SURROUND OFF.

• You can turn the 3D HEADPHONE

function on or off with a single press.

• The 3D HEADPHONE function does

not work properly for mono sound.

• The 3D HEADPHONE function

cannot play back Dolby Surround Pro

Logic sound correctly.

Using the TV’s menu

„ Other surround functions

You can enjoy enhanced sounds while using

headphones with one of the following four

surround functions:

EXT SETTING

DANCE CLUB:

This function creates a dance club

atmosphere. It does not work properly for

mono sound.

CONCERT HALL:

This function creates a concert hall

atmosphere. It does not work properly for

mono sound.

„ y (S-VIDEO input)

STADIUM:

This function creates a stadium atmosphere.

It does not work properly for mono sound.

You can connect a device (such as an S-VHS

VCR) to enjoy the high-quality picture of the

S-VIDEO signal (Y/C signal).

HYPER SOUND:

Preparation:

This function enhances mono sounds to

create a stereo sound feel. It does not work

properly for stereo sound.

• First read the device’s instruction manual

and “Additional preparation” on page 39

to connect the device to the TV properly.

Second, follow the device’s instruction

manual to set the device so that it sends an

S-VIDEO signal (Y/C signal) to the TV.

• Do not set y (S-VIDEO input) to an

EXT terminal connected to a device

which cannot output an S-VIDEO (Y/C

signal). If it is set wrongly, a picture

cannot appear.

To cancel the function:

Press the 6 buttons to choose

SURROUND OFF.

• The above function does not work

properly for Dolby Surround encoded

programmes.

1 Choose an EXT terminal

2 Press the yellow button and set the

y (S-VIDEO input).

Then press the a button

An y (S-VIDEO input) mark is

displayed. You can view an S-VIDEO

signal (Y/C signal) instead of the regular

video signal (composite signal).

Using the TV’s menu

To cancel the y (S-VIDEO input)

3 Press the 6 buttons to choose a

name. Then press the a button

The LIST disappears and the name is

assigned to the EXT terminal.

• You cannot choose an EXT terminal

name that is not on the name list

(LIST).

setting:

Press the yellow button and turn off y

(S-VIDEO input) mark. The regular video

signal (composite signal) pictures are

resumed.

• The EXT-1 terminal does not support

S-VIDEO signal (Y/C signal) and you

cannot set y (S-VIDEO input) in

the EXT-1 terminal.

To erase a name assigned to the

EXT terminal:

Choose a blank space.

• Setting y (S-VIDEO input) changes

the head character from “E” to “S”.

When an EXT terminal receives a

normal video signal, “E1”, “E2”, “E3”

or “E4” appears on the display. This

changes to “S2”, “S3” or “S4” when it

receives an S-VIDEO signal.

4 Press the a button to complete

the setting

„ DUBBING

You can choose a signal source to be output

from the EXT-2 terminal.

You can do this with the output signal of the

device connected to another EXT terminal,

or the picture and sound from a TV channel

you are currently viewing.

• Even a device which can output an S-

VIDEO signal (Y/C signal) may

output a regular video signal

(composite signal) depending on the

device setting. If a picture cannot

appear because the y (S-VIDEO

input) setting has been made, read the

device instruction manual carefully

again to check for the device settings.

1 Press the 5 buttons to choose

the arrow from the menu

2 Press the 6 buttons to choose an

EXT terminal or TV.

Then press the a button

„ LIST

You can store a name for each of the devices

connected to each EXT terminal. Giving a

name to an EXT terminal makes the EXT

terminal number appear on the screen,

together with its name.

1 Choose an EXT terminal

2 Press the blue button to display the

name list (LIST)

The arrow in the menu represents a signal

flow. The left side of the arrow shows a

signal source output from the EXT-2

terminal.

EXT-1/EXT-3/EXT-4:

The output signal of the device connected

to an EXT terminal passes through the TV

and is output from the EXT-2 terminal.

TV:

The picture and sound of the TV channel

you are currently viewing are output from

the EXT-2 terminal.

Using the TV’s menu

FEATURES

• During dubbing, you cannot turn off

the TV. Turning off the TV also turns

off the output from the EXT-2

terminal.

• When you choose an EXT terminal as

an output, you can view a TV

programme or a picture from the other

EXT terminal while dubbing the

picture from a device connected to the

EXT terminal onto a VCR connected

to the EXT-2 terminal.

„ SLEEP TIMER

You can set the TV to automatically turn off

after a specified period of time.

• The RGB signals from TV games

cannot be output.Teletext programmes

cannot be output.

1 Choose SLEEP TIMER, then press

the a button

A Sub-menu of the SLEEP TIMER

function appears.

2 Press the 5 buttons to set the

period of time.

Then press the a button

You can set the period of time a

maximum of 120 minutes (2 hours) in 10

minute steps.

• One minute before the SLEEP TIMER

function turns off the TV, “GOOD

NIGHT!” appears.

• The SLEEP TIMER function cannot

be used to turn off the TV’s main

power.

• When the SLEEP TIMER function is

on, you can display the sub-menu of

the SLEEP TIMER function again to

confirm or change the remaining

period of time of the SLEEP TIMER

function. Press the a button to leave

the menu after confirming or changing

the remaining time.

To cancel the SLEEP TIMER

function:

Press the 2 button to set a period of time

to “OFF”.

Using the TV’s menu

„ BLUE BACK

4 Press the 6 buttons to choose a

TV channel

You can set the TV to automatically change

to a blue screen and mute the sound if the

signal is weak or absent, or when there is no

input from an external device.

Every time you press the 6 buttons, the

Programme number (PR) changes, and the

picture of the TV channel registered in the

Programme number (PR) is displayed on

the screen.

ON:

This function is turned on.

OFF:

This function is turned off.

5 Press the blue button and set the

CHILD LOCK function.

„ CHILD LOCK

Then press the a button

n (CHILD LOCK) appears and the TV

channel is locked.

When there is a TV channel you do not want

your children to watch, you can use the

CHILD LOCK function to lock out the TV

channel. Even when a child chooses a

programme number (PR) for a locked TV

channel the screen will change to blue and

display n (CHILD LOCK) so the TV channel

cannot be viewed. Unless you enter a pre-set

ID number by a special operation, the lock

cannot be released and the child cannot view

the TV channel.

To reset the CHILD LOCK function:

Press the blue button again.

n (CHILD LOCK) disappears.

To disable easy resetting of the CHILD

LOCK function, the menu disappears if

you choose the CHILD LOCK function

and press the a button.

To set the CHILD LOCK function

To view a locked TV channel

1 Choose CHILD LOCK, then press

the o button

1 Choose a programme number (PR)

in which a TV channel locked with

the number buttons or PR LIST

The screen changes to blue and the n

(CHILD LOCK) appears. You cannot

view the TV channel.

“SET ID NO.” (ID number setting screen)

appears.

2 Set the ID number to your liking

2 Press the

(Information) button to

1 Press the 6 buttons to choose

a number.

display “ID NO.” (ID No. input

screen).

2 Press the 5 buttons to move

the cursor.

3 Press the a button

The Sub-menu of CHILD LOCK appears.

3 Press the number buttons to enter

the ID number

The lock is temporarily released so you

can view the TV channel.

Using the TV’s menu

If you have forgotten the ID

number:

INSTALL

Perform step 1 of “To set the CHILD

LOCK function”. After confirming the ID

number, press the b button to exit the

menu.

• Even if you reset the lock temporarily,

it does not mean that the CHILD

LOCK function set for the TV channel

is cancelled. The next time anyone

tries to view the TV channel, it will be

locked again.

• When you want to cancel the CHILD

LOCK function, you must perform the

operation “To set the CHILD LOCK

function” again.

• To stop it being easy to choose the

programme number (PR) of a locked

TV channel, the programme number

(PR) has been set so that it cannot be

chosen by the 6 buttons or the

buttons of the TV.

„ LANGUAGE

You can choose the language you want to use

for the on-screen display from the language

list in a menu.

1 Choose LANGUAGE, then press

the a button

A sub-menu of the LANGUAGE function

appears.

• To stop it being easy to reset the lock,

“ID NO.” (ID No. input screen) is set

so that it cannot appear unless you

press the

(Information) button.

„ DECODER (EXT-2)

2 Press the 5 and 6 buttons to

choose a language.

You can only use this function if you have a

decoder connected to a T-V LINK

compatible VCR, which in turn is connected

to the EXT-2 terminal. To use this function,

see “Using the DECODER (EXT-2)

function” on page 35.

Then press the a button

„ AUTO PROGRAM

To receive SKY 1 you need a satellite tuner.

You must have the satellite tuner set to SKY

1 before starting the AUTO PROGRAM

function.

Caution

• If you have not connected a decoder with

a T-V LINK compatible VCR to the EXT-2

terminal, setting this function to “ON” by

mistake causes the picture/sound of a TV

channel you are currently viewing to

disappear.

You can automatically store the TV channels

for which you have the best reception. Store

them in the TV’s programme numbers (PR)

list by doing the following.

1 Choose AUTO PROGRAM

2 Press the a button to start the

AUTO PROGRAM function

The AUTO PROGRAM menu appears

and the TV channels you receive are

automatically registered in the

programme numbers (PR) list.

Using the TV’s menu

• To cancel the AUTO PROGRAM

• If a TV channel you want to view is

not set to a programme number (PR),

set it manually using the MANUAL

function. For details, see “EDIT/

MANUAL” on page 30.

function, press the b button.

• The AUTO PROGRAM function does

not set the programme number PR 0

(AV) for your video cassette recorder.

You will need to set this using the

manual function.

• In some areas you may get TV

reception from more than one

After the TV channels have been

registered in the programme

numbers (PR), the EDIT menu

appears.

• You can now edit the programme

numbers (PR) using the EDIT/

MANUAL function. For details, see

“EDIT/MANUAL” on page 30.

• If you do not need to use the EDIT/

MANUAL function, go to the next

step.

transmitter, for example, different ITV

regions. In this case each TV channel

could be set twice. If this happens, the

first set of channels will have the

stronger signal. If you want to delete

the second set of channels, you will

have to do it manually (see page 33).

„ EDIT/MANUAL

The EDIT/MANUAL functions are divided

into two types:

3 Press the a button to display the

• editing the current programme numbers

(PR) (EDIT functions); and

T-V LINK menu

• manually storing a TV channel you want

to view a programme number (PR)

(MANUAL function).

Here are the details about these functions:

Caution

• Using the MOVE, DELETE or INSERT

functions rewrites the current programme

numbers (PR) list. Therefore, the

programme numbers (PR) of some of the

TV channels will change.

• Using the MANUAL function for a TV

channel for which the CHILD LOCK

function has been set cancels the CHILD

LOCK function for that channel.

• Using the MANUAL function for a TV

channel for which the DECODER (EXT-2)

function has been set to ON returns the

setting of the DECODER (EXT-2) function

for that channel to OFF.

4 If you do not have a T-V LINK

compatible VCR connected:

Press the b button to leave the T-V

LINK menu.

The T-V LINK menu disappears and all

the settings are completed.

If you have a T-V LINK compatible

VCR connected to the EXT-2

terminal:

See “Downloading data to a VCR” on

page 35 to transmit the programme

number (PR) data to the VCR.

• When a TV channel has already been

registered in PR 99, using the INSERT

function deletes that TV channel.

Using the TV’s menu

1 Choose EDIT/MANUAL, then press

3 Press the a button to complete

the settings

the a button

The T-V LINK menu appears.

• For programme number PR 0, “AV”

appears in the programme numbers

(PR) list.

• An EXT terminal number does not

appear in the programme numbers

(PR) list.

4 If you do not have a T-V LINK

compatible VCR connected:

Press the b button to exit the T-V LINK

menu.

The T-V LINK menu disappears and all

the settings are completed.

• The CH number is a number unique to

the TV and corresponding to the

channel number of a TV channel. For

the relationship of a channel number

and a CH number, see “CH

If you have a T-V LINK compatible

VCR connected:

Follow the operating procedure

“Downloading data to a VCR” on page 35

to transmit the programme number (PR)

data to the VCR.

NUMBER” on page 34.

2 Follow the description for a

function you want to use

MOVE

1 Press the 6 buttons to choose a

TV channel

MOVE:

This function changes a programme

number (PR) of a TV channel.

Every time you press the 6 buttons, the

programme number (PR) changes and the

picture of the TV channel stored in the

programme number (PR) appears on the

screen.

ID:

This function registers a channel name

(ID) to a TV channel.

INSERT:

2 Press the 3 button to start the

This function adds a new TV channel in

the current programme numbers (PR) list

by using the CH number.

MOVE function

• You cannot use the INSERT function

if you do not know a channel number

of a TV channel. Use the MANUAL

function to register a TV channel in the

programme number (PR).

DELETE:

This function deletes a TV channel you do

not want to list.

3 Press the 6 buttons to choose a

new programme number (PR)

MANUAL:

This function manually stores a new TV

channel in a programme number (PR).

To cancel the MOVE function:

Press the

(Information) button.

Using the TV’s menu

4 Press the 2 button to change the

programme number (PR) of a TV

channel to a new programme

number (PR)

5 Press the 6 buttons to choose

the channel name (ID)

To cancel the ID function:

Press the

(Information) button.

6 Press the a button to give a

1 Press the 6 buttons to choose a

TV channel

channel name (ID) to a TV channel

Every time you press the 6 buttons, the

programme number (PR) changes and the

picture of the TV channel stored in the

programme number (PR) appears on the

screen.

• You can give your own unique channel

name (ID) to the TV channel. When

you have finished step 3, do not go to

step 4. Press the 5 buttons to move

the cursor, and press the 6 buttons

to choose each character of the channel

name (ID). Then press the a button

to register the channel name (ID) to the

TV channel.

2 Press the red button to start the ID

function

INSERT

Preparation:

• You need to find the CH number for the

TV channel. Find the CH number from

the “CH NUMBER” table on page 34

based on the channel number of the TV

channel.

3 Press the 6 buttons to choose

the first character of a channel

name (ID) you want to give the TV

channel

1 Press the 6 buttons to choose a

programme number (PR) for which

you will register a new TV channel

2 Press the green button and start

the INSERT function

4 Press the blue button to display the

ID LIST (channel name list)

To cancel the INSERT function:

Press the

(Information) button.

Using the TV’s menu

MANUAL

3 Press the number buttons to enter

the remaining CH number

1 Press the 6 buttons to choose a

programme number (PR) for a new

TV channel

The TV shifts to registration mode.

When the registration is completed, the

picture of the TV channel appears on the

screen.

• The CH number is a number given to

each broadcast frequency that carries a

TV channel. If the TV cannot detect

the TV channel corresponding to the

broadcast frequency indicated by the

CH number, a “no-signal” picture

appears.

2 Press the blue button to activate

the MANUAL function

DELETE

To cancel the MANUAL function:

Press the

(Information) button.

1 Press the 6 buttons to choose a

TV channel

3 Press the green or red button to

search for a TV channel

Scanning stops when the TV finds a TV

channel. Then the TV channel is

displayed.

Every time you press the 6 buttons, the

programme number (PR) changes and the

picture of the TV channel stored in the

programme number (PR) appears on the

screen.

4 Press the green or red button

repeatedly until the TV channel you

want appears

If the TV channel reception is poor:

Press the blue or yellow button to fine-

tune the TV channel.

2 Press the yellow button to delete

the TV channel

5 Press the a button and register

the TV channel to a programme

number (PR)

The TV channel is deleted from the

programme numbers (PR) list.

The normal EDIT menu is resumed.

Using the TV’s menu

„ CH NUMBER

DEMO

• When you want to use the INSERT

function on page 32, find the CH number

corresponding to the channel number of

the TV channel from this table.

If you want to know a particular TV

channel’s channel menu, look in TV

listings magazines or contact the

broadcaster.

The DEMO function automatically

demonstrates some of the TV functions.

Channel

E21

E22

E23

E24

E25

E26

E27

E28

E29

E30

E31

E32

E33

E34

E35

E36

E37

E38

E39

E40

E41

E42

E43

E44

E45

Channel

E46

E47

E48

E49

E50

E51

E52

E53

E54

E55

E56

E57

E58

E59

E60

E61

E62

E63

E64

E65

E66

E67

E68

E69

CH 21

CH 22

CH 23

CH 24

CH 25

CH 26

CH 27

CH 28

CH 29

CH 30

CH 31

CH 32

CH 33

CH 34

CH 35

CH 36

CH 37

CH 38

CH 39

CH 40

CH 41

CH 42

CH 43

CH 44

CH 45

CH 46

CH 47

CH 48

CH 49

CH 50

CH 51

CH 52

CH 53

CH 54

CH 55

CH 56

CH 57

CH 58

CH 59

CH 60

CH 61

CH 62

CH 63

CH 64

CH 65

CH 66

CH 67

CH 68

CH 69

Choose ON or OFF. Then press the

a button

The DEMO function is set to ON, and the

demonstration will start.

To stop the demonstration:

Press one of the buttons on the remote

control.

When the DEMO function is set to ON:

Each time the TV is turned on, the

demonstration starts automatically. If you do

not want that to happen, cancel the DEMO

function:

1 Display the DEMO menu again

2 Press the 6 buttons to choose

OFF

3 Press the a button to cancel the

DEMO function

Additional menu operations

Downloading data to a VCR

Using the DECODER (EXT-2)

function

You can send the latest programme numbers

(PR) data to a VCR with the T-V LINK

function.

• You can only do this when a T-V LINK

compatible VCR is connected to the EXT-

2 terminal.

If you have a decoder connected to a T-V

LINK compatible VCR, which in turn is

connected to the EXT-2 terminal, use the

DECODER (EXT-2) function to unscramble

the scrambled TV channels.

• This only works when the T-V LINK

menu is being displayed.

1 Turn on the decoder power

2 Display the scrambled TV channel

on the TV

Even if the decoder is working, a

scrambled picture appears.

3 Press the a button to display the

1 Turn on the VCR

The MENU (main menu) appears.

2 Press the a button

4 Press the 6 buttons to choose

FEATURES. Then press the a

button

The data transmission begins.

The FEATURES menu appears.

The T-V LINK menu disappears once the

data transmission ends.

When the T-V LINK menu changes

over to another menu:

The TV has finished its menu. This new

menu is operated from the VCR. See the

VCR instruction manual for what to do

next.

5 Press the 6 buttons to choose

DECODER (EXT-2). Then press the

5 buttons to choose ON

If “FEATURE NOT AVAILABLE”

appears at the T-V LINK menu, check the

following three items. Then press the a

button to retry data transmission.

• Has a T-V LINK compatible VCR

been connected to the EXT-2

An unscrambled picture appears.

To cancel the DECODER (EXT-2)

function:

Press the 5 buttons to choose OFF.

6 Press the a button to complete

the setting

terminal?

• Has the VCR power been turned on?

• Does the SCART cable that connects

the EXT-2 terminal to the T-V LINK

compatible VCR have all its proper

connections?

The T-V LINK menu appears.

Additional menu operations

the front panel of your TV set can be used

to control the volume of all the speakers at

once.

• The settings of the TV speakers on each

menu are related, if you change one of

them the others will change automatically.

• Setting the volume of the amplifier too

high may damage the front speakers.

7 Follow “Downloading data to a

VCR” on page 35 to transmit the

programme number (PR) data to

the VCR

8 If you have another TV channel you

want to unscramble using a

decoder, repeat steps 2 to 7

„ Turning the TV’s speakers off

If the DECODER (EXT-2) function has

been set to “ON” but the TV channel

cannot be unscrambled, check the

following:

• Has the decoder been connected to the

VCR properly according to the VCR

and decoder instruction manuals?

• Has the decoder power been turned

on?

Preparation:

• Press the 3D button to choose

“SURROUND OFF”, then turn off the

surround function.

1 Press the a button to display the

MENU (main menu)

2 Press the 6 buttons to choose

SOUND SETTING. Then press the

a button to display the SOUND

SETTING menu

• Can the TV channel be unscrambled

with a decoder?

• Do you need to change the VCR

settings in order to connect the

decoder? Confirm that the VCR is set

properly by rechecking the VCR

Instruction manual.

The SOUND SETTING menu appears.

Additional Sound settings

Follow “Connecting speakers or an

amplifier” on page 40 to connect the

speakers and amplifier, then set the functions

depending on the connection you have made.

3 Press the 6 buttons to choose

SPEAKER. Then press the 5

buttons to choose OFF

When connecting an audio system

(front speakers and an amplifier):

Follow “Turning the TV’s speakers off” and

“Using the TV speakers as the centre

speakers for the PRO LOGIC 3D-PHONIC

function”.

The sound from the TV speakers is cut.

4 Press the a button to complete

the settings

The menu disappears.

When connecting surround speakers:

Follow “Setting the DOLBY PRO LOGIC

function”.

When connecting both an audio

system (front speakers and an

amplifier) and surround speakers:

Follow “Turning the TV’s speakers off” and

“Setting the DOLBY PRO LOGIC function”.

• The 5 buttons of the TV remote

control and the r (volume) buttons at

Additional menu operations

„ Using the TV speakers as the

centre speakers for the PRO

LOGIC 3D-PHONIC function

When the PRO LOGIC 3D-PHONIC

function is operating, the front speakers and

TV speakers are all used. The TV speakers

take the role of a centre speaker. It makes

spoken dialogues more vivid and easier to

listen to.

5 Press the a button to complete

the settings

The menu disappears.

• Use the amplifier volume to control

and set the volume of the front

speakers to fit in with the TV speakers.

„ Setting the DOLBY PRO LOGIC

function

Set the items in the sub-menu of the DOLBY

PRO LOGIC function properly, and use the

test signal to control the volume of the

speakers so that you can listen to the sounds

from them evenly. Be sure to do this

operation before using the DOLBY PRO

LOGIC function.

Preparation:

• If you have had headphones connected to

your TV set, disconnect them.

1 Press the a button to display the

MENU (main menu)

2 Press the 6 buttons to choose

DIGITAL SURROUND. Then press

the a button to display the

DIGITAL SURROUND menu

Preparation:

• If you have had the headphones connected

to your TV set, disconnect them.

• Increase the volume of the TV speakers to

a level at which you ordinarily listen. If

you do not do this before starting the

operation, it is impossible to control the

volume from within the function.

When you are using an audio system,

however, set the amplifier volume to zero

to cut the front speakers. Then pre-set the

TV sound volume level to about 10.

3 Press the 6 buttons to choose

PRO LOGIC 3D-PHONIC. Then

press the 3 button to display the

sub-menu of PRO LOGIC 3D-

PHONIC function

1 Press the a button to display the

MENU (main menu)

2 Press the 6 buttons to choose

DIGITAL SURROUND. Then press

the a button to display the

DIGITAL SURROUND menu

4 Press the 6 buttons to choose

TV SPEAKER. Then press the 5

buttons to choose CENTRE

3 Press the 6 buttons to choose

DOLBY PRO LOGIC. Then press

the 3 button to display the sub-

menu of the DOLBY PRO LOGIC

function

L/C/R:

L/C/R is used to make all the sound come

from the TV speakers.

OFF:

OFF is used to cut sound from the TV

speakers.

When the sound quality of the audio

system is better than the TV’s speakers,

you can set the TV SPEAKER to OFF to

cut the sound of the TV speakers.

Additional menu operations

4 Press the 6 buttons to choose

TV SPEAKER. Then press the 5

buttons to choose the TV speaker

setting

7 Press the a button to complete

the settings

The menu disappears.

• For details about listening positions,

see “Connecting speakers or an

amplifier” on page 40.

When you are connecting only

surround speakers:

• When you use both an audio system

and the TV speakers and they are not

matched in sound quality, you can

change over the TV SPEAKER setting

to OFF to cut the TV speakers.

Set TV SPEAKER to L/C/R.

When you are connecting both an

audio system and surround

speakers:

Set TV SPEAKER to CENTRE. All the

TV speakers act as a centre speaker.

(However, almost no sound is emitted

from the woofer.)

5 Press the 6 buttons to choose

TEST MODE. Then press the 5

buttons to choose ON

Test signals are output alternately from

each of the speakers.

To make sounds come from the

front speakers of the audio system:

Slowly turn up the amplifier volume until

the volume from the front speaker is

roughly equal to that from the TV

speakers or surround speakers.

6 Press the 5 buttons to adjust the

sound volumes of the speakers so

that you can listen to the sounds at

the same volume when you are

sitting where you would normally

sit to watch the TV

LEFT/CENTRE/RIGHT/SURROUND:

LEFT and RIGHT stands for the left and

right of the front speakers. CENTRE

refers to the centre speaker, and

SURROUND refers to surround speakers.

Additional preparation

Connecting external equipment

Connect the equipment to the TV, making

the correct rear panel and front panel

connections.

1 VCR (composite signal)

2 VCR (composite signal/S-VIDEO signal)

3 T-V LINK compatible VCR (composite

signal/S-VIDEO signal)

4 Decoder

5 DVD player (composite signal/S-VIDEO

signal)

6 DVD player (composite signal/RGB

signal)

Before connecting anything:

• Read the manuals that came with the

equipment.

Depending on the equipment, the

connection method may be different from

the diagram. Also, the equipment settings

may need to change depending on the

connection method.

7 TV game (composite signal/RGB signal)

8 TV game (composite signal/S-VIDEO

signal)

• Turn off all the equipment including the

TV.

9 Headphones

• The “Specifications” on the back cover

give the details of the EXT terminals. If

you are connecting equipment not listed

in the following connection diagram, see

the table to choose the best EXT terminal.

• Connecting cables are not supplied.

0 Camcorder (composite signal/S-VIDEO

signal)

- SCART cable

= Audio cable

~ Video cable

! S-VIDEO cable

Back of the TV

WOOFER

EXT-2

EXT-3

)

SURROUND

REAR

EXT-1

Back of the TV

WOOFER

AUDIO OUT

EXT-2

EXT-3

)

EXT-1

SURROUND

REAR

Additional preparation

• The video/sound signal from an EXT

terminal cannot be output.

• Teletext programmes cannot be output.

„ Equipment which can output the

S-VIDEO signal (Y/C signal) such

as an S-VHS VCR

Connect the equipment to an EXT terminal

(but not the EXT-1 terminal).

Connecting speakers or an

amplifier

You can choose between an S-VIDEO signal

(Y/C signal) and a regular video signal

(composite signal). For details of how to

operate the equipment, see “y (S-VIDEO

input)” on page 25.

See the audio equipment diagram, and

connect the audio equipment to the TV.

Before connecting anything:

• Read the manuals that came with the

amplifier and speakers.

• Turn the TV and amplifier off.

• Use impedance 8-ohm type speakers for

surround speakers.

• To prevent magnetism from the speakers

affecting the TV screen, use magnetic-

shielded speakers for the front speakers.

• Connecting cables are not supplied.

„ T-V LINK compatible VCR

Be sure to connect the T-V LINK compatible

VCR to the EXT-2 terminal. If not, the T-V

LINK function will not work properly.

• When connecting a T-V LINK compatible

VCR to the EXT-2 terminal, be sure to

connect the decoder to the VCR. If not,

the T-V LINK function may not work

properly. After you have stored TV

• Pay attention to the positive and

channels in the programme numbers (PR)

list, set the DECODER (EXT-2) function

for the programme number (PR) to ON to

unscramble a scrambled TV channel. For

details, see “Using the DECODER (EXT-

2) function” on page 35.

negative polarities when connecting the

surround speakers to your TV.

• For the best effect, position the surround

speakers at least 1 metre above the heads

of seated viewers.

• If you want to use your external Dolby

Surround decoder, connect it to the

AUDIO OUT terminals. Then set all

surround functions of the TV to OFF.

• The output from the AUDIO OUT

terminal is not cut off connecting

headphones to the TV.

„ Connecting headphones

Connect the headphones with a stereo mini-

jack (3.5 mm diameter) to the headphone

jack at the TV front panel.

• When you connect the headphones, the

TV speakers go off.

„ Video or sound signal output from

the EXT-2 terminal

„ Audio amplifier and front speakers

You can use external front speakers to listen

to the TV sound instead of the TV speakers.

For details of how to operate them, see

“Turning the TV’s speakers off” on page 36.

Also note that when you want to use the PRO

LOGIC 3D-PHONIC function, you can set it

to issue sound from both of the TV speakers

and external front speakers so that you can

listen to spoken dialogues more clearly and

easily. For details, see “Using the TV

speakers as the centre speakers for the PRO

LOGIC 3D-PHONIC function” on page 37.

• You cannot cut the sound from the front

speaker even if you connect a headphone

to the TV.

You can change over the output of the video/

sound signal from the EXT-2 terminal. This

is useful when you want to dub the video/

sound from another device onto the VCR

connected to the EXT-2 terminal. For details

on how to do this, see “DUBBING” on

page 26.

„ TV output from the EXT-1 terminal

The video/sound signal of a TV channel you

are viewing is always output from the EXT-1

terminal.

• Changing over a programme number (PR)

also changes over the TV output from the

EXT-1 terminal.

Additional preparation

„ External surround speakers

You can connect external surround speakers

to the TV so that you can use the “DOLBY

PRO LOGIC” on page 23. Before using the

DOLBY PRO LOGIC function, however,

follow the description “Setting the DOLBY

PRO LOGIC function” on page 37.

Removing and Fitting the

Woofer Unit

„ Removing the woofer unit

The woofer unit may be removed as

necessary.

1 Amplifier

Remove the connector while pushing the

connector lever on the WOOFER terminal,

lift the woofer, and remove it.

2 Front speakers (magnetic-shielded type)

3 Surround speakers (impedance 8 ohm type)

AUDIO OUT

Lever

SURROUND

REAR

(Terminals on rear)

„ Fitting the woofer unit

Fit the woofer unit in the reverse order to that

described in “Removing the woofer unit”.

Align the projection on the base of the

woofer unit with the hole in the top of the

TV, and insert the connector into the

WOOFER terminal.

„ Positioning the speakers

„ Cautions when fitting the woofer

unit

• Check that the woofer unit is fitted

correctly on the top of the TV.

• Do not use excessive force when inserting

the connector into the WOOFER terminal.

Use of excessive force may damage the

connector.

Approx.

45 degrees

Troubleshooting

If a problem arises while you are using the TV, please read this troubleshooting guide carefully

before you ask to have the TV repaired. You may be able to fix it easily by yourself. For example,

if the mains plug is disconnected from the mains outlet, or the TV aerial has problems, you may

think there is a problem with the TV itself.

Important:

• This troubleshooting guide only covers problems whose causes are not easy to decide. If you

have a question when you are operating a function, read the page(s) for that function carefully,

not this troubleshooting guide.

• If you follow the advice in this troubleshooting guide without any success, unplug the mains

plug and ask for your TV to be repaired. Do not attempt to repair the TV by yourself or to

remove the rear cover of the TV.

• If the TV or aerial suffers interference

from other equipment, stripes or noise

may appear in the picture. Move any

equipment such as an amplifier, personal

computer, or a hair drier, that can cause

interference away from your TV. Or try

moving the TV. If the aerial suffers

interference from a radio tower or high-

voltage wire, please contact your local

dealer.

• If the TV suffers interference from signals

reflecting from mountains or buildings,

double-pictures (ghosting) will occur. Try

to change the aerial’s direction or replace

it with one with better directionality.

• Are your COLOUR SYSTEM settings

correct? Follow the description

„ If you cannot turn on the TV

• Is the mains plug connected to the mains

outlet?

• Is the power lamp lit? If not, press the

main power button.

„ No picture or no sound

• Have you chosen a TV channel with very

poor reception? If so, the BLUE BACK

function will be activated: the entire

screen becomes blue, and the sound is

muted. If you still want to view the TV

channel, follow the description “BLUE

BACK” on page 28 to try to change the

BLUE BACK function setting to OFF.

• Have you connected headphones to the

TV?

Connecting headphones to the TV turns

off the TV speakers.

“COLOUR SYSTEM” on page 20 to try

to solve the trouble.

• Have you set the SPEAKER function to

OFF? Follow the description

“SPEAKER” on page 22 to check the

• Have the COLOUR and BRIGHT settings

been adjusted properly? Follow the

description “Picture Adjustment” on

page 19 to try to adjust them properly.

• Videotaping teletext is not recommended

because it may not record correctly.

• When a white and bright still image (such

as a white dress) is displayed on the

screen, the white part may look as if it is

coloured. This is unavoidable due to the

nature of the picture tube itself, and not

due to a TV failure. When the picture

disappears from the screen, the unnatural

colours will also disappear.

SPEAKER function setting.

„ Poor picture

• If noise (snow) totally block out the

picture, there may be a problem with the

aerial or aerial cable. Check the following

to try to solve the problem:

– Have the TV and aerial been connected

properly?

– Has the aerial cable been damaged?

– Is the aerial pointing in the right

direction?

– Is the aerial itself faulty?

Troubleshooting

• If you bring a magnetised equipment such

as a speaker near to your TV, the picture

may be warped or unnatural colours now

appear at the corners of the screen. In this

case, keep the equipment away from your

TV. If speakers cause this to happen, use

magnetic-shielded speakers instead.

• A picture may be tilted due to the earth’s

own magnetic field. If so, use the

“PICTURE TILT (not AV28R25EK/

AV28R250EK)” on page 21 to correct the

tilt.

• The TV may make a crackling sound due

to a sudden change in temperature. The

picture or sound may be normal. If you

hear crackling sounds frequently while

you are viewing the TV, there may be

other causes. As a precaution, ask your

service technician to inspect it.

„ Poor sound

• Have you adjusted BASS or TREBLE

properly? If not, follow the description

“Sound Adjustment” on page 21.

• When TV channel reception is poor, it can

be hard to hear stereo or bilingual sound.

In this case, follow the description

“STEREO / I • II” on page 21 to hear the

sound more easily by changing it to a

mono sound.

„ If the TV does not respond to the

remote control

• Have the batteries of the remote control

worn out? Follow the description “Putting

the batteries into the Remote control” on

page 6 and replace them with new

batteries.

• Have you attempted to use the remote

control from the sides or rear of the TV or

from more than seven metres away from

the TV? Use the remote control in the

front of your TV or from less than seven

metres away.

• When you are viewing a teletext

programme, you cannot operate the

menus. Press the b button to return to

the ordinary TV programme, and then try

operating the menus.

• Touching the screen may cause you to

feel a slight electric shock due to its static

electricity. This is unavoidable due to the

construction of the picture tube. It is not a

problem with the TV. You can rest

assured that this static discharge is not

harmful.

• If the TV will not respond suddenly, press

the main power button on the TV and turn

off the main power. Press the main power

button again to turn on the TV. If the TV

returns to a normal state, it is not a failure.

„ Other issues

• When the SLEEP TIMER function

operates, the TV is automatically turned

off. If the TV is turned off suddenly, try to

press the # (standby) button to turn on

the TV once again. If the TV goes back to

normal, there is no problem.

• When the TV is receiving a wide-screen

signal (WSS) or a signal from an external

device affecting the screen size, the

ZOOM mode automatically changes.

When you want to resume the previous

ZOOM mode, press the c button

again.

HP Hewlett Packard Workstation P9615A#xxx User Manual
JVC 50052496 User Manual
KitchenAid KGCT366G User Manual 1
LG Electronics LG Life Good Computer Monitor L1919SP User Manual
Microsoft Laser Desktop Keyboard 6000 v3 0 User Manual
Moffat Blue Seal E516C CB User Manual
Philips 25PT 5107 User Manual
Philips Brilliance 181AS User Manual
Philips DFU DEC2008 User Manual
Philips HTS335W User Manual