JVC AV 28WT2EK User Manual

COLOUR TELEVISION

CONTENTS

AV-24WT2EK

AV-28WT2EK

SAFETY PRECAUTIONS ......... 2

Locations of remote control

buttons............................... 4

Locations of TV buttons and

parts ................................... 5

PREPARATION AND BASIC

OPERATION ....................... 6

SOUND AND PICTURE.......... 12

OTHER FEATURES ............... 14

TELETEXT ............................. 17

OTHER PREPARATION ......... 19

TROUBLESHOOTING ........... 24

SPECIFICATIONS .................. 26

INSTRUCTIONS

Thank you for purchasing this JVC colour television.

To ensure your complete understanding, please read this manual

thoroughly before operation.

SAFETY PRECAUTIONS

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

TO ENSURE PERSONAL SAFETY, OBSERVE THE FOLLOWING RULES

REGARDING THE USE OF THIS UNIT.

• Operate only from the power source specified (AC 220 – 240V, 50 Hz) on the unit.

• Avoid damaging the AC plug and power cord.

• Avoid improper installation and never position the unit where good ventilation is

unattainable.

When installing this television, distance

recommendations must be maintained

between the floor and wall, as well as

15 cm

installment in a tightly enclosed area or

piece of furniture. Please adhere to the

minimum distance guidelines show for

safe operation.

10 cm

15 cm

• Do not allow objects or liquid into the cabinet openings.

• In the event of a fault, unplug the unit and call a service technician. Do not

attempt to repair it yourself or remove the rear cover.

* When you do not use this TV set for a long period of time, be sure to disconnect

the power plug from the AC outlet.

WARNING:

DO NOT cut off the mains plug from this equipment. If the plug fitted is not

suitable for the power points in your home or the cable is too short to reach a power

point, then obtain an appropriate safety approved extension lead or adaptor or

consult your dealer.

If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug

immediately, to avoid a possible shock hazard by inadvertent connection to the

mains supply.

If a new mains plug has to be fitted, then follow the instruction given below:

IMPORTANT.

DO NOT make any connection to the larger terminal which is marked with the letter

E or by the safety earth symbol

or coloured green or green-and-yellow.

The wires in the mains lead on this product are coloured in accordance with the

following code:

Blue:

Brown:

Neutral

Live

As these colours may not correspond with the coloured marking identifying the

terminals in your plug proceed as follows:

The wire which is coloured blue must be connected to the terminal which is marked

with the letter N or coloured black.

The wire which is coloured brown must be connected to the terminal which is

marked with the letter L or coloured red.

When replacing the fuse only a correctly rated approved type should be used and be

sure to re-fit the fuse cover.

IF IN DOUBT — CONSULT A COMPETENT

ELECTRICIAN.

How To Replace The Fuse

Open the fuse compartment with the blade screwdriver,

and replace the fuse.

Fuse

Some Do’s And Don’ts On The Safe Use Of Equipment

This equipment has been designed and manufactured to meet international safety

standards but, like any electrical apparatus, care must be taken if you are to obtain

the best results and safety is to be assured.

read the operating instructions before you attempt to use the equipment.

ensure that all electrical connections (including the mains plug, extension

leads and interconnections between pieces of equipment) are properly

made and in accordance with the manufacturer’s instructions.

consult your dealer if you are ever in doubt about the installation or

operation or safety of your equipment.

be careful with glass panels or doors on equipment.

DON’T continue to operate the equipment if you are in any doubt about it working

normally, or if it is damaged in any way — switch off — withdraw the mains

plug and consult your dealer.

DON’T remove any fixed cover as this may expose dangerous voltages.

DON’T leave equipment switched on when it is unattended unless it is specifically

stated that it is designed for unattended operation or has a standby mode.

Switch off using the switch on the equipment and make sure that your family

know how to do this. Special arrangements may need to be made for infirm

or handicapped people.

DON’T use equipment such as personal stereos or radios that may distract you

when driving. It is illegal to watch television while driving.

DON’T listen to headphones at high volume, as such use can permanently damage

your hearing.

DON’T obstruct the ventilation of the equipment, for example with curtains or soft

furnishings. Overheating will cause damage and shorten the life of the

equipment.

DON’T use makeshift stands and NEVER fix legs with wood screws — to ensure

complete safety always fit the manufacturer’s approved stand or legs with

the fixings provided according to the instructions.

DON’T allow electrical equipment to be exposed to rain or moisture.

ABOVE ALL

—

NEVER let anyone especially children push anything into holes, slots or any

other opening in the case — this could result in a fatal electrical shock.

NEVER guess or take chances with electrical equipment of any kind. It is

better to be safe than sorry.

—

Locations of remote control buttons

OUTSIDE BUTTONS

INSIDE BUTTONS

How to open the cover.

ZOOM

HOLD

SIZE

MODE

REVEAL

CANCEL

SUBPAGE

INDEX

STORE

VCR TEXT

Inserting batteries into your remote

control

1 Mute button

p.12

p.9

2 Number buttons

3 ZOOM button

4 Hyper Sound button

5 Information button

6 TV button

p.16

Use two AAA/R03 dry cell batteries.

p.12

Insert two batteries, observing the

and

polarities, inserting the

end first.

p.9, 14

7 Volume –/+ buttons

8 Standby button

9 Colour buttons

0 TV/text button

- OK button

p.10

p.8, 10

p.17

p.9

= PR channel

buttons

! Teletext/VCR control buttons

p.17

@ VCR/TEXT selector switch

• When switched to the VCR side, the ! buttons function as

the JVC VCR control buttons.

CAUTION:

• Follow the cautions printed on the batteries.

Notes:

• For details on button functions, see the JVC VCR

• Battery life is approx. six months to one year, depending on

manual.

frequency of use.

• Depending on your VCR, the remote control may not

• If the remote control operates erratically, replace the batteries.

• We recommend that you use the supplied batteries

temporarily and replace them as soon as operation becomes

erratic. The supplied batteries are for operational testing of the

remote control, not for regular use.

operate perfectly, and may not even control the VCR at

all.

• When switched to the TEXT side, the ! buttons function

as teletext control buttons.

Locations of TV buttons and parts

FRONT PANEL

Push to open

(behind the door)

ECO

EXT-3

1 2

5 6

7 8 9 0

REAR PANEL

1 Remote control sensor

2 ECO sensor

3 Headphone jack (mini jack)

4 EXT-3 terminals

p.7

p.6, 19

p.10

5 Volume button

(Press this button to display the volume

level indicator. Press the 6 Up/down

buttons to change volume while the

volume level indicator is displayed.)

6 Up/down buttons

p.10

(You can use this button as the

buttons of the PR channel. Pressing the

5 Volume button makes this button

function as the Volume –/+ buttons.)

7 Hyper Sound lamp

8 ECO lamp

p.12

p.13

9 Sleep timer lamp

0 Power lamp

p.14

p.8, 10

p.6, 19

p.6

- Main power button

= EXT-2 terminal

~ EXT-1 terminal

! Aerial socket

EXT-1

EXT-2

PREPARATION AND BASIC OPERATION

1. Connecting the aerial and VCR

Notes:

If not connecting a VCR, do 1 only.

• For further details, refer to manuals

provided with the devices you are

connecting.

• Connecting cables are not supplied.

• You can view video from a VCR

without doing 3. For details, refer to

the manual provided with your VCR.

If connecting a VCR, proceed 1 → 2 → 3.

VHF/UHF outdoor aerial

EXT-1

EXT-2

To RF

output

To AV IN / OUT

terminal

To aerial input

VCR / S-VHS VCR

2. Connecting other external devices

Conditions:

• This TV set has external device connectors, EXT-1 to EXT-3 to which

you can connect a VCR. However, there are some differences in

functions among them. Consult the following table before making

connections.

EXT-1

√ *1

√ *2

√ *1

–

EXT-2

√ *1

√ *3

√ *1

–

EXT-3 (front)

*1 Select VIDEO or S-VIDEO

mode from the EXT SETTING

menu. For details, see page 19

“EXT SETTING.”

*2 Only the TV broadcast is

output.

VIDEO IN

√

–

VIDEO OUT

S-VIDEO IN

S-VIDEO OUT

RGB IN

–

√

–

*3 TV broadcasts or inputs from

EXT-1 or 3 can be output. For

details, see page 19

AUDIO-L IN

AUDIO-R IN

AUDIO-L OUT

AUDIO-R OUT

Others

√

√ *2

√

√ *3

√

–

“DUBBING.”

–

• Automatic detection and

switching of input mode.

• Automatic detection and

switching of ZOOM mode.

• Use headphones with a stereo mini jack (dia. 3.5 mm).

When using headphones, the speakers will not output sound.

• For further details, refer to manuals provided with the devices you are

connecting.

• Connecting cables are not supplied.

Devices which can be connected to the terminals on the rear panel

1 VCR

3 Decoder

2 S-VHS VCR

4 TV game

1 2 3

1 2

EXT-1

EXT-2

Devices which can be connected to the terminals on the front panel

(behind the door)

Camcorder

EXT-3

Push to open

TV game

To audio

output

Headphones

To video output

3. Connecting the power cord

Insert the power plug into an AC outlet (AC 220 – 240 V,

50 Hz).

Power cord

AC outlet

4. Turning the power and TV on

1. ^{Press the Main power button on the TV to turn}

the power on.

The Power lamp lights red (power on), then green (TV

on).

Note:

• You can also press the PR channel

If the power lamp stays red and does not change to green:

Your TV is in the standby mode. Press the Standby button on the

remote control to turn your TV on.

button, a number button or the

up/down button on the front panel to

turn the TV on.

5. Initial Settings

Note:

• When the TV is first turned ON, it enters into the initial setting mode, and

the JVC logo is displayed.

• The TV enters into the initial setting

mode only once when the TV is first

turned ON. If you turn the TV off or exit

from the setting menu while performing

the initial settings by mistake, you must

redo the initial settings, “LANGUAGE”

and “AUTO PROGRAM”, following the

procedures described in page 20.

1. ^{Press any button on the remote control.}

LANGUAGE menu appears.

Selecting the on-screen language

You can select your language from ten languages listed on the LANGUAGE

menu. The displayed menus on the screen are described in the selected

language.

button to select

2. ^Press

LANGUAGE

ENGLISH

FRAN¸CAIS

DEUTSCH

ITALIANO

CASTELLANO

NEDERLANDS

DANSK

ENGLISH.

NORSK

SVENSKA

SUOMI

:EXIT

:OK

3. ^{Press OK button.}

English is set for the on-screen display

description, and the AUTO PROGRAM menu

appears.

AUTO PROGRAM

START

CANCEL

:EXIT

Automatically allocating stations to PR channels

To view a TV programme, you must first allocate broadcast stations to PR

channels. You can automatically allocate up to 99 stations to PR channels

PR1 to PR 99 on this TV. Broadcast stations that can be received are

automatically determined and set to PR channels.

4. ^{Press OK button.}

Broadcast stations are automatically allocated

to the PR channels.

AUTO PROGRAM

Note:

CH 60

81%

• If you want to quit automatic allocation

in the middle, press the TV button.

:OK

:EXIT

The EDIT menu is displayed after the

allocation is completed.

Notes:

EDIT

• When the previous tables broadcast

channels cannot be received, nothing

is set to that particular PR channels.

• To store different broadcast channels

to PR 1 to 6, see "EDIT/MANUAL" on

page 21.

ID CH/CC

-----

• If you want to edit PR channels or allocate a

station to PR0 (AV) channel, see page 21

“EDIT/MANUAL” for procedural description.

• When carrying out automatic programming,

the following broadcast channels and Station

IDs are automatically set to PR channels

PR1 to 6 by the AUTO PROGRAM function.

BBC1 CH 21

BBC2 CH 22

ITV CH 23

CH4 CH 24

CH5 CH 25

CH 26

CH 27

CH 28

CH 29

TV OK

:MOVE

:ID

:INSERT

:DELETE

:MANUAL

PR channel

PR 1

Broadcast channel

BBC1

Station ID

BBC1

BBC2

PR 2

BBC2

PR 3

ITV

* To receive SKY1, a satellite broadcast

reception tuner is required. Before

carrying out automatic setting, receive

SKY1 on the satellite broadcast

reception tuner.

PR 4

CHANNEL4

CHANNEL5

SKY1*

CH4

PR 5

CH5

PR 6

No indication

● The procedure is complete.

Press the TV button to exit the menu.

6. Viewing a television programme

1. ^{Select a PR channel.}

Selection

• Press the PR channel

button.

Notes:

• If the picture is not clear or no colour

appears, change the colour system

manually (see page 13 for details).

• Enter “0” when selecting an AV

channel (PR 0 channel).

Direct channel selection

• Press the corresponding number buttons.

Example: To select channel 6, press “6”.

To select channel 12, press “1” and “2”.

PR LIST

To use the PR LIST to select a PR channel

1. Press Information button.

The PR LIST appears.

-----

BBC1

BBC2

ITV

CH4

CH5

• To exit the PR LIST, press TV

button.

:EXIT

:OK

Note:

• The

PR LIST

2. Press

channel.

• Press

button to select a PR

button to view the next

mark will appear on the PR

-----

BBC1

BBC2

ITV

CH4

CH5

channel when the CHILD LOCK setting

is on (see page 15).

page of the PR LIST.

• Press

previous page of the PR LIST.

button to view the

:EXIT

:OK

3. Press OK button.

2. ^{Press the Volume -/+ button.}

The Volume level indicator appears and the

volume changes as you press the Volume -/+

buttons.

Turning the TV and power off

1. ^{Press the Standby button to turn the TV off.}

The Power lamp changes from green to red.

The TV enters standby mode.

Note:

2. ^{Press the Main power button on the TV to turn}

• To save energy, we recommend that

you turn the main power off if you do

not plan to use your TV for a long time.

the main power off.

The Power lamp goes off.

To select a channel without using the remote

control

You can also use the buttons on the front panel of the TV.

Note:

1. ^{Press the Up/down button to turn your TV on.}

• If your TV does not turn on, press the

Main power button, and then press the

Up/down button again.

The Power lamp changes from red to green.

2. ^{Press the Up/down button to select the PR}

channel.

Note:

3. ^{Adjust the volume.}

1. Press the Volume button.

• PR channel selection is not available

while the volume level indicator is

displayed.

The volume level indicator appears.

2. Press the Up/down button while the volume level

indicator is displayed.

● To turn off your TV, press the Main power button.

The Power lamp goes off.

Viewing images from external devices

Notes:

1. ^{Repeatedly press the 0 button to select the EXT}

• If the picture is not clear or no colour

appears, change the colour system

manually (see page 13).

• When selecting an EXT terminal with

no input signal, the EXT number and

ID become fixed on screen.

terminal.

The current selection appears, and disappears after several

seconds.

When a station is not registered to the PR 0 (AV) channel, pressing

the 0 button changes the selection as follows:

TV mode

EXT modes

PR channel

number

EXT-1

EXT-2

EXT-3

When a station is registered to the PR 0 (AV) channel, pressing the

0 button changes the selection as follows:

TV modes

PR 0 channel

EXT modes

EXT-1

EXT-2

PR channel

number

EXT-3

TV mode:

Shows images input from an external device (such as a VCR) or TV

aerial connected to the aerial socket of your TV.

EXT modes:

Shows images input from an external device (such as a VCR)

connected to the selected EXT terminal.

• To use S-Video mode to view input from an S-VHS VCR, see “To

select S-VIDEO input for a terminal” on page 19. When selecting

EXT-1 or EXT-2 input terminals as S-VIDEO input, E1 or E2 changes

to S1 or S2 in the display.

SOUND AND PICTURE

MUTE

MULTI SOUND

TINT

You can mute the volume to 0

instantly. This is convenient when

answering the phone or when

receiving visitors.

You can select the multi sound mode You can choose from among three

for stereo broadcast programmes

and bilingual programmes.

TINT modes.

1. Press OK.

Note:

The MENU appears.

• The MULTI SOUND function has no

effect on programmes other than A2 or

NICAM broadcast programmes.

1. Press

(Mute).

2. Press

to select

The sound is muted.

PICTURE SETTING, then

press OK.

1. Press OK.

The PICTURE SETTING menu

appears.

The MENU appears.

To restore the sound:

Press the Mute button again.

PICTURE SETTING

SOUND SETTING

EXT SOURCE

FEATURES

INSTALL

DEMO

3. Press

to select TINT.

PICTURE SETTING

TINT

NORMAL

CONTRAST

BRIGHT

SHARP

COLOUR

HUE

:OK

:EXIT

HYPER SOUND

ECO MODE

COLOUR SYSTEM

4:3 AUTO ASPECT

OFF

PAL

REGULAR

You can enjoy sounds with a wider

ambiance by Hyper sound.

2. Press

to select

SOUND SETTING, then

press OK.

:OK

:EXIT

1. Press

(Hyper Sound).

The HYPER SOUND ON appears.

• The Hyper Sound lamp lights.

:RESET

The SOUND SETTING menu

appears.

4. Press

to select a tint

SOUND SETTING

mode.

STEREO/I•II

BASS

TREBLE

BALANCE

HYPER SOUND

I II

COOL:

HYPER SOUND ON

A cool white colour base with a

boost in the colour and contrast

levels. Creating a more vivid

picture.

OFF

:OK

:EXIT

To return to normal sound:

Press the Hyper Sound button again.

3. Press

to select

• HYPER SOUND can be also set to

ON by operating MENU.

WARM:

STEREO/I•II.

Use this mode when viewing film

programmes.

Notes:

1. Press the OK button.

The MENU appears.

• The multi sound mode display is

different from the broadcast

programme.

• The multi sound function does not

work in EXT modes.

NORMAL:

A normal white colour base with no

boost in the colour or contrast

levels.

2. Press

button to select

SOUND SETTING, and press OK

button.

The SOUND SETTING menu

appears.

The STEREO/I•II does not appear

in SOUND SETTING menu.

5. Press OK.

This completes the setting.

4. Press

to select a

3. Press

button to select

multi sound mode.

HYPER SOUND.

: Stereo sound

SOUND SETTING

STEREO/I•II

BASS

TREBLE

BALANCE

HYPER SOUND

I II

: Bilingual I (Sub I)

: Bilingual II (Sub II)

: Normal sound

OFF

:OK

:EXIT

5. Press OK.

This completes the setting.

4. Press

OFF.

button to select ON,

Note:

• When you display the current PR

channel number, the current multi sound

mode appears for approximately 3

seconds.

5. Press the OK button.

This completes the setting.

• If you turned on HYPER

SOUND, the Hyper Sound

lamp lights.

2. Press

to select

SOUND SETTING, then

press OK.

COLOUR SYSTEM

PICTURE/SOUND

ADJUSTMENT

The colour system is automatically

selected, but if the picture is not

clear or no colour appears, select

the colour system manually.

The SOUND SETTING menu

appears.

SOUND SETTING

You can adjust the picture and

sound as you like.

STEREO/I•II

BASS

TREBLE

I II

1. Press OK.

To adjust the picture

BALANCE

HYPER SOUND

OFF

The MENU appears.

:OK

:EXIT

1. Press OK.

2. Press

to select

PICTURE SETTING, then

press OK.

The MENU appears.

3. Press

to select an

2. Press

to select

item, and press

adjust it.

The PICTURE SETTING menu

appears.

PICTURE SETTING, then

press OK.

Item

The PICTURE SETTING menu

appears.

PICTURE SETTING

3. Press

to select

COLOUR SYSTEM.

PICTURE SETTING

Weaker

BASS

(low frequency sound)

Stronger

TINT

NORMAL

Weaker

TREBLE

(high frequency sound)

Stronger

TINT

NORMAL

CONTRAST

BRIGHT

SHARP

COLOUR

HUE

CONTRAST

BRIGHT

SHARP

Left

BALANCE

(audio balance)

Right

COLOUR

HUE

ECO MODE

COLOUR SYSTEM

4:3 AUTO ASPECT

OFF

PAL

REGULAR

ECO MODE

COLOUR SYSTEM

4:3 AUTO ASPECT

OFF

NTSC3.58

REGULAR

4. Press OK.

:OK

:EXIT

:OK

:EXIT

This completes the setting.

:RESET

3. Press

to select an

4. Press

to select the

item, and press

adjust it.

ECO MODE

appropriate colour system.

PAL:

PAL system.

When you set ECO MODE to ON,

the screen contrast is automatically

adjusted to a setting suitable for the

brightness of your room.

This reduces eye strain and the

power consumption of the TV.

CONTRAST

NTSC3.58:

NTSC 3.58 MHz system.

• To return to the default settings,

press blue button.

NTSC4.43:

NTSC 4.43 MHz system.

Item

Lower

Darker

Softer

Lighter

CONTRAST

(picture contrast)

Higher

1. Press OK.

AUTO:

Automatic colour system selection.

The MENU appears.

BRIGHT

(picture brightness)

Brighter

Notes:

2. Press

to select

PICTURE SETTING, then

press OK.

SHARP

(picture sharpness)

Sharper

• Auto may not function properly

depending on signal quality. If the

picture is abnormal in AUTO mode,

select another colour system

manually.

• When in TV mode (PR 1 to PR 99),

you cannot select AUTO, NTSC

3.58 or NTSC 4.43.

COLOUR

(picture colour)

Deeper

The PICTURE SETTING menu

appears.

Reddish

HUE

(picture hue)

Greenish

3. Press

MODE.

to select ECO

Note:

• When in TV mode (PR 0), you

cannot select NTSC 3.58 or NTSC

4.43.

PICTURE SETTING

• You can adjust the HUE (picture

hue) only when the colour system

is NTSC 3.58 or NTSC 4.43.

TINT

NORMAL

CONTRAST

BRIGHT

SHARP

COLOUR

HUE

ECO MODE

COLOUR SYSTEM

4:3 AUTO ASPECT

5. Press OK.

4. Press OK.

OFF

PAL

REGULAR

This completes the setting.

:OK

:EXIT

To adjust the sound

:RESET

1. Press OK.

4. Press

OFF.

to select ON,

The MENU appears.

5. Press OK.

This completes the setting.

• If you turned on ECO MODE, the

ECO lamp lights.

OTHER FEATURES

INFORMATION

SLEEP TIMER

BLUE BACK

You can display the PR LIST or the

current time.

You can set the TV to automatically When viewing a PR channel with no

turn off after a specified period of

time.

or poor reception, or if there is no

input from an external device, you

can mute the sound and change the

1. Press

repeatedly.

(Information)

Note:

• The SLEEP TIMER does not turn off the picture into a blue picture.

The display changes cyclically in

the following order.

Main power.

1. Press OK.

The MENU appears.

PR LIST

2. Press

to select

-----

BBC1

BBC2

ITV

2. Press

to select

FEATURES, then press OK.

The FEATURES menu appears.

FEATURES

CH4

CH5

The FEATURES menu appears.

FEATURES

SLEEP TIMER

BLUE BACK

CHILD LOCK

SLEEP TIMER

BLUE BACK

CHILD LOCK

:OK

:EXIT

:OK

:EXIT

3. Press

to select BLUE

3. Press

to select SLEEP

BACK, then press OK.

TIMER, then press OK.

The BLUE BACK menu appears.

BLUE BACK

The SLEEP TIMER menu appears.

SLEEP TIMER

21:30

OFF

Current time

OFF

120

:OK

:EXIT

:OK

:EXIT

No indication

4. Press

OFF.

to select ON or

4. Press

to select a

period of time.

5. Press OK.

You can set the period of time a

maximum of 120 minutes in 10

minute increments.

About PR LIST:

This completes the setting.

• Ten positions including the currently

selected PR channel will be displayed

as a list.

OFF:

Turns off the SLEEP TIMER.

Press

to select the

desired PR channel. For details see

page 9.

5. Press OK.

The selected period of time is

About the current time display:

This TV uses teletext data to determine

the current time.

displayed for approx. 3 seconds.

SLEEP TIMER 60

• If the TV has not received a station

that has teletext data since it was

turned on, the time display is blank.

To view the current time, select a

station that is broadcasting teletext

data. As long as you do not turn off

the TV, then even if you select other

stations, the time will still be

• The Sleep timer lamp lights if you

set the SLEEP TIMER.

To display the remaining Sleep timer

time:

Perform steps 1 to 3 to display the

SLEEP TIMER menu, and press OK

button when you finish checking the

time.

displayed.

To turn off the Sleep timer:

Perform steps 1 to 3 to display the

SLEEP TIMER menu, press

button to

select “OFF”, and then press OK button.

• The Sleep timer lamp goes out.

Note:

• One minute before the SLEEP TIMER

turns off the TV, “GOOD NIGHT!”

appears. Three seconds before the

SLEEP TIMER turns off the TV, “JVC” is

displayed on the screen.

7. Press OK.

CHILD LOCK

DEMONSTRATION

This completes the setting.

Notes:

You can lock some PR channels to

prevent your children from watching

them.

The demonstration runs

automatically and introduces the

menus of this TV’s main features.

• You cannot select a locked PR channel

using the PR channel

• Even if you can select a locked channel

and display it, you can not view the

programme of the locked channel.

buttons.

1. Press OK.

To set the CHILD LOCK

The MENU appears.

2. Press

to select DEMO,

To view a locked PR

channel

1. Press OK.

then press OK.

The MENU appears.

The demonstration begins.

• To stop the demonstration, press

any button on the remote control.

2. Press

to select

1. Select a locked PR channel.

FEATURES, then press OK.

• Use the number buttons to select

the PR channel.

The FEATURES menu appears.

FEATURES

The locked channel is displayed.

SLEEP TIMER

BLUE BACK

CHILD LOCK

:OK

:EXIT

2. Press

to select CHILD

(Information).

The ID NO. input menu appears.

3. Press

LOCK, then press 0 button.

The SET ID NO menu appears.

SET ID NO

ID NO. :

0000

3. Press the number buttons

to enter the ID number.

:OK

:EXIT

You are now viewing the locked PR

channel.

4. Enter the ID number.

1. Press

2. Press

to select a number.

to move the cursor.

If you forget the ID number:

Perform steps 1 to 3 of “To set the

CHILD LOCK”. After you confirm the ID

number, press the TV button to exit the

menu.

5. Press OK.

The CHILD LOCK menu appears.

CHILD LOCK

ID CH/CC

-----

BBC1 CH 21

BBC2 CH 22

ITV CH 23

CH4 CH 24

CH5 CH 25

CH 26

CH 27

CH 28

CH 29

:EXIT

:OK

:LOCK

6. Press

to select a PR

channel, then press blue

button.

The selected PR channel is locked.

CHILD LOCK

ID CH/CC

-----

BBC1 CH 21

BBC2 CH 22

ITV CH 23

CH4 CH 24

CH5 CH 25

CH 26

CH 27

CH 28

CH 29

:EXIT

:OK

:CANCEL

• To cancel the CHILD LOCK:

Press blue button again.

• Repeat step 6 to lock all PR

channels which you want to lock.

OTHER FEATURES

16:9 ZOOM mode:

Use to expand a wide picture (16:9

aspect ratio).

:Default position

:The picture is moved from

default position.

ZOOM

Select a ZOOM mode to change the

picture format. You can enlarge the

picture to fill the wide TV screen

(16:9 aspect ratio). In addition, you

can stretch a normal picture (4:3

aspect ratio) to fill the wide TV

screen.

Note:

• If you change the ZOOM mode, the

picture returns to its default

position.

(16:9 ZOOM)

14:9 ZOOM mode:

Automatic ZOOM

selection (AUTO mode)

Use to expand a picture with a 14:9

aspect ratio.

Notes:

You can set your TV to automatically

select the optimum ZOOM mode to

suit the picture format.

• The picture format information of the

present broadcasting programme may

be received as WSS (Wide Screen

Signalling). When AUTO mode is

selected for ZOOM mode and the WSS

signal is received, this TV automatically

selects the optimum ZOOM mode

corresponding to the WSS signal.

However, in the case of weak WSS

signal reception, this function may not

work correctly. In this case, select the

optimum ZOOM mode manually.

• If the EXT-1 terminal’s input is from a

picture signal with a 16:9 aspect ratio

picture format, the ZOOM mode may

automatically changes to FULL mode.

This is because the TV detects an

identification signal which is not an WSS

signal.

1. Press ZOOM repeatedly to

select AUTO.

(14:9 ZOOM)

16:9 ZOOM SUBTITLE mode:

Use to expand a picture with a 16:9

aspect ratio having subtitles at the

bottom of the screen.

Your TV automatically selects the

optimum ZOOM mode to suit the current

programme’s picture format.

Note:

• This function may not work

correctly depending on the

programme. In this case, select the

optimum ZOOM mode manually.

SUBTITLE SUBTITLE

(16:9 ZOOM SUBTITLE)

To preset a ZOOM mode for the

normal picture:

Note:

• In 16:9 ZOOM SUBTITLE mode,

the top of the picture are slightly

cut off.

You can preset one of the three

ZOOM modes, REGULAR,

PANORAMIC or 14:9 ZOOM, as the

ZOOM mode for the normal picture

(4:3 aspect ratio).

FULL mode:

Manual ZOOM selection

Uniformly stretches the left and right

sides of a normal picture (4:3 aspect

ratio) to fill the wide TV screen.

You can select a ZOOM mode

manually.

1. Press OK

1. Press ZOOM repeatedly to

select a ZOOM mode.

The MENU appears.

2. Press

to select

PICTURE SETTING, then

press OK.

The picture expands.

(FULL)

REGULAR mode:

Use to view a normal picture (4:3

aspect ratio) unchanged.

Note:

The PICTURE SETTING menu

appears.

• For pictures with a 16:9 aspect

ratio that have been squeezed into

a normal picture (4:3 aspect ratio),

select FULL mode to restore their

original dimensions.

3. Press

to select

4:3 AUTO ASPECT.

PICTURE SETTING

To move the picture vertically:

TINT

NORMAL

CONTRAST

BRIGHT

SHARP

COLOUR

HUE

ECO MODE

COLOUR SYSTEM

4:3 AUTO ASPECT

If you cannot see subtitles at the

bottom of the screen, or if the top or

bottom is cut off, move the picture

vertically.

PANORAMIC mode:

Stretches the left and right sides of

a normal picture to fill the screen, in

a way that does not appear

unnatural.

OFF

PAL

REGULAR

:OK

:EXIT

Note:

• You cannot move the picture vertically in

:RESET

AUTO, REGULAR and FULL mode.

4. Press

mode.

to select ZOOM

1. Press ZOOM.

The current ZOOM mode is

displayed.

(PANORAMIC)

5. Press OK.

Note:

This completes the setting.

16:9 ZOOM

• In PANORAMIC mode, the top,

bottom, left and right of the picture

are slightly cut off.

2. Before the display

disappears, press

move the picture up or

down.

TELETEXT

Note:

2. Press

(TV/text).

DISPLAY CANCEL

• If you have trouble receiving teletext

broadcasts, consult your local dealer or

the teletext station.

You can search for a teletext page

while watching TV.

(Outside buttons)

1. Select a teletext page.

TV mode

ZOOM

The TV searches for a teletext

page.

TEXT TEXT TEXT

2. Press DISPLAY CANCEL.

The TV programme appears.

P100 P101 P102 P103

When the TV finds the teletext page,

its page number appears in the

upper left of the screen.

Text mode

3. Select a page number.

Note:

Browse:

(Inside buttons)

• If selecting something other than

REGULAR or FULL mode for

ZOOM mode, the page number

does not appear on the screen.

Press the PR channel

button on

the remote control.

HOLD

SIZE

Direct selection:

MODE

REVEAL

CANCEL

Press the number buttons to enter a

three-digit page number.

3. Press

(TV/text) when

the page number is on the

screen.

SUBPAGE

INDEX

STORE

Colour button selection:

Press a colour button to select the

corresponding page number on the

bottom line of the screen.

VCR TEXT

Notes:

SIZE

• Category names of teletext pages

may appear instead of page

numbers.

• In principle, ZOOM mode is fixed to

FULL mode when you view Teletext

programmes.

1 Colour buttons

2 TV/text button

3 VCR/TEXT selector switch

You can double the height of the

teletext display.

• When this switch is set to the

TEXT side, the following buttons

function as the teletext control

button.

1. Press SIZE repeatedly.

• Some Teletext programmes display

a mixture of regular TV

programmes and Text information.

When viewing these Teletext

programmes, pay attention to the

following points.

– Teletext pages cannot be

selected with the Colour buttons.

To change to other Teletext

pages, select the Teletext page

that you want to view with the

TEXT

SIZE

4 MODE button

5 HOLD button

6 SUB PAGE button

7 STORE button

8 REVEAL button

9 SIZE button

TEXT

SIZE

0 INDEX button

- DISPLAY CANCEL button

Channel

buttons.

buttons or number

– ZOOM mode returns to the mode

you selected before you started

viewing Teletext programmes. If

part of the Teletext information is

missing at the top or bottom of

the screen, press the ZOOM

BASIC TELETEXT

OPERATION

button to switch ZOOM mode to

FULL mode or REGULAR mode.

● To return to TV mode, press the

TV/text again.

You can view two types of teletext

broadcasts on the TV: Fastext and

WST. The TV automatically

recognizes the type of teletext

broadcast.

Note:

• You can also return to TV mode by

pressing the TV button.

Condition:

• The VCR/TEXT selector switch must

already be set to the TEXT side.

1. Select a channel with a

teletext broadcast.

TELETEXT

HOLD

LIST MODE

SUB PAGE

You can hold a teletext page on the

screen for a desired length of time,

even while several other teletext

pages are being received.

If you store the numbers of teletext

pages you view often, you can

quickly call up a desired teletext

page whenever you like.

Some teletext pages include sub-

pages that are automatically

displayed. You can hold any sub-

page, or view it at any time.

Note:

1. Press HOLD.

1. Call up a teletext page with

sub-pages.

• You can store up to 64 pages in

memory. You can store four pages in

each channel from 1 to 15 (60 pages),

and four pages that are the same for all

channels above channel 15 (4 pages).

is displayed in the upper left of

the screen, and the teletext page is

held on the screen.

2. Press SUB PAGE.

3. Enter the number of the

sub-page.

To store the page

numbers

Example:

To select the 3rd sub-page, press

number buttons “0”, “0”, “0”, and “3”.

P100 P101 P102 P103

To release hold mode:

Press HOLD button again.

1. Press MODE to engage

LIST mode.

Note:

• You can also select a sub page by

pressing the red or green colour button.

Stored page numbers are displayed

at the bottom of the screen.

INDEX

2. Press a colour button, then

enter the number of the

teletext page.

Just press INDEX button to return to

the index page.

To assign other pages to remaining

colour buttons, repeat this

operation.

1. Press INDEX.

Fastext/WST:

Returns to page 100 or a previously

specified page.

3. Press and hold STORE.

The four page numbers blink white

to indicate that they are stored in

memory.

LIST mode:

Returns to the page number displayed in

the lower left area of the screen.

To call up a stored page

REVEAL

1. Press MODE to engage

LIST mode.

Some teletext pages include hidden

text (such as answers to a quiz).

Stored page numbers are displayed

at the bottom of the screen.

1. Press REVEAL.

To release LIST mode:

Press MODE button again.

Each time you press REVEAL

button, text is hidden or revealed.

2. Press a colour button to

which a page has been

assigned.

1 + 2 =

2 x 3 =

P100 P101 P102 P103

1 + 2 = 3

2 x 3 = 6

P100 P101 P102 P103

OTHER PREPARATION

To give an EXT ID to an

EXT input terminal

EXT SETTING

DUBBING

You can select S-VIDEO or normal

input for the EXT-1 and EXT-2

terminals, and you can give an EXT

ID to each EXT input terminal.

Select output to a VCR or other

device connected to the EXT-2

terminal. Note that you cannot

output from the EXT-2 terminal when

the TV is turned off.

1. Press OK.

The MENU appears.

2. Press

to select EXT

SOURCE, then press OK.

To select S-VIDEO input

for a terminal

Note:

The EXT SOURCE menu appears.

• RGB signals from TV games and

TELETEXT screens cannot be output

from EXT-2 terminal.

3. Press

to select EXT

1. Press OK.

SETTING, then press OK.

The MENU appears.

The EXT SETTING menu appears.

1. Press OK.

2. Press

to select EXT

4. Press

to select an

The MENU appears.

SOURCE, then press OK.

EXT input terminal.

2. Press

to select EXT

The EXT SOURCE menu appears.

EXT SOURCE

5. Press blue button.

SOURCE, then press OK.

EXT SETTING

DUBBING

The EXT SOURCE menu appears.

EXT S-IN

EXT-1

EXT-2

:OK

:EXIT

3. Press

to select

EXT-3

DUBBING, then press OK.

:OK

:EXIT

3. Press

to select EXT

The DUBBING menu appears.

SETTING, then press OK.

DUBBING

EXT-1

6. Repeatedly press

select a character.

EXT SETTING

The EXT SETTING menu appears.

EXT-2

EXT-3

EXT SETTING

EXT S-IN

EXT-1

EXT-2

EXT S-IN

EXT-1

EXT-2

EXT-3

:OK

:EXIT

:OK

:ID

:EXIT

:OK

4. Press

to select the

input which you want to

output from EXT-2.

4. Press

to select an

7. Press

to move the

EXT input terminal.

cursor forward.

• Pressing

cursor backward.

• To cancel the operation, press the

(Information) button.

EXT SETTING

button moves the

5. Press yellow button.

TV:

The sound and picture of the

currently selected PR channel is

output from EXT-2, so you can

record the output on a VCR

connected to the EXT-2 terminal

while watching a video input from

the EXT-1 or EXT-3 terminal.

The S-VIDEO input indication

appears.

• To select normal input, press

yellow button again.

EXT S-IN

EXT-1

EXT-2

VCR-1

EXT SETTING

EXT-3

EXT S-IN

EXT-1 S

EXT-2

:EXIT

:OK

EXT-3

DUBBING

EXT-1

:EXIT

:OK

:ID

8. Press OK.

EXT-2

EXT-3

Note:

• If you want to set an EXT ID here,

perform the operation procedures

from the step 4 in the next

column.

• To erase EXT ID, reset the EXT ID to a

blank space.

:OK

:EXIT

● This completes the procedure.

Press the TV button to exit the

menu.

6. Press OK.

DUBBING

EXT-1

The menu disappears.

EXT-2

EXT-3

:OK

:EXIT

5. Press OK.

The menu disappears.

OTHER PREPARATION

AUTO PROGRAM

LANGUAGE

AUTO PROGRAM

CH 60

81%

:OK

:EXIT

You can select one of ten languages You can automatically allocate up to

for the on-screen display.

99 stations to PR channels PR 1 to

PR99 on this TV.

When the TV receives a signal

describing the station’s name, it

allocates those stations, station IDs,

and registers then as they were

preset at the JVC factory.

EDIT

1. Press OK.

ID CH/CC

-----

The MENU appears.

BBC1 CH 21

BBC2 CH 22

ITV CH 23

CH4 CH 24

CH5 CH 25

CH 26

2. Press

to select

INSTALL, then press OK.

The INSTALL menu appears.

INSTALL

CH 27

CH 28

CH 29

1. Press OK.

TV OK

:MOVE

LANGUAGE

AUTO PROGRAM

EDIT/MANUAL

The MENU appears.

:ID

:INSERT

:DELETE

:MANUAL

2. Press

to select

:EXIT

:OK

Note:

INSTALL, then press OK.

• If a station you want to view is not

allocated to a PR channel, perform

Manual allocation (see page 23).

The INSTALL menu appears.

3. Press

to select

LANGUAGE, then press

OK.

3. Press

to select AUTO

PROGRAM, then press OK.

● The procedure is complete.

Press the TV button to exit the

menu.

The AUTO PROGRAM menu

appears.

The LANGUAGE menu appears.

LANGUAGE

ENGLISH

FRAN¸CAIS

DEUTSCH

ITALIANO

CASTELLANO

NEDERLANDS

DANSK

AUTO PROGRAM

START

CANCEL

:OK

:EXIT

NORSK

SVENSKA

SUOMI

Note:

• If you make a mistake when

selecting your country, or do not

want to use the Automatic

allocation function, select

CANCEL, and then press OK

button to return to the INSTALL

menu.

:OK

:EXIT

4. Press

to select a

language.

5. Press OK.

4. Press OK.

This completes the setting.

The PR channel is automatically set

and the EDIT menu is displayed.

• If you want to edit PR channels or

allocate a station to PR0 (AV)

channel, see page 21 “EDIT/

MANUAL” for procedural

description.

To delete a station from a To change the PR channel

PR channel number of a station

EDIT/MANUAL

You can change PR channel settings

by doing any of the following:

• You can delete an unwanted

station from a PR channel,

• You can change the PR channel

number of a station,

• You can add station IDs to PR

channels,

• You can add a new station to a PR

channel, or

1. Press

to select the

1. Press

station.

to select the

station you want to delete.

EDIT

ID CH/CC

-----

ID CH/CC

-----

BBC1 CH 21

BBC2 CH 22

ITV CH 23

CH4 CH 24

CH5 CH 25

CH 26

BBC1 CH 21

BBC2 CH 22

ITV CH 23

CH4 CH 24

CH5 CH 25

CH 26

CH 27

CH 28

CH 29

CH 27

CH 28

CH 29

• You can manually allocate the

desired station to a PR channel.

TV OK

:MOVE

TV OK

:MOVE

:ID

:INSERT

:DELETE

:MANUAL

:ID

:INSERT

:DELETE

:MANUAL

2. Press yellow button.

2. Press

EDIT

To edit PR channels

EDIT

ID CH/CC

-----

ID CH/CC

-----

1. Press OK.

BBC1 CH 21

BBC2 CH 22

ITV CH 23

CH4 CH 24

CH5 CH 25

CH 26

BBC1 CH 21

BBC2 CH 22

ITV CH 23

CH4 CH 24

CH5 CH 25

CH 26

The MENU appears.

2. Press

to select

INSTALL, then press OK.

CH 28

CH 29

CH 30

CH 27

CH 28

CH 29

The INSTALL menu appears.

TV OK

:MOVE

TV OK

STORE:

3. Press

to select EDIT/

:ID

:INSERT

:DELETE

:MANUAL

MANUAL, then press OK.

The EDIT menu appears.

EDIT

Note:

• Stations allocated to PR channels

following the deleted PR channel

number are shifted back by one to

the preceding PR channel number.

3. Press

to move the

ID CH/CC

-----

selected station to the

desired PR channel

number.

BBC1 CH 21

BBC2 CH 22

ITV CH 23

CH4 CH 24

CH5 CH 25

CH 26

• To cancel the operation, press the

(Information) button

CH 27

CH 28

CH 29

EDIT

TV OK

:MOVE

ID CH/CC

-----

BBC1 CH 21

BBC2 CH 22

:ID

:INSERT

:DELETE

:MANUAL

CH 27

4. Use any of the procedures

described in the following

pages to change the PR

channel settings.

ITV CH 23

CH4 CH 24

CH5 CH 25

CH 26

CH 28

CH 29

TV OK

STORE:

● This completes the procedure.

Press the TV button to exit the

menu.

4. Press

EDIT

ID CH/CC

-----

BBC1 CH 21

BBC2 CH 22

CH 27

ITV CH 23

CH4 CH 24

CH5 CH 25

CH 26

CH 28

CH 29

TV OK

:MOVE

:ID

:INSERT

:DELETE

:MANUAL

OTHER PREPARATION

6. Press OK.

Returns to the EDIT menu.

EDIT

To add a station ID to a

station

To add a new station to a

PR channel

ID CH/CC

-----

1. Press

station.

to select the

1. Press

to select the

BBC1 CH 21

BBC2 CH 22

ITV CH 23

CH4 CH 24

CH5 CH 25

CH 26

MOVIE CH 27

CH 28

CH 29

row containing the PR

channel number to which

you want to add a station.

EDIT

ID CH/CC

-----

BBC1 CH 21

BBC2 CH 22

ITV CH 23

CH4 CH 24

CH5 CH 25

CH 26

ID CH/CC

-----

BBC1 CH 21

BBC2 CH 22

ITV CH 23

CH4 CH 24

CH5 CH 25

CH 26

TV OK

:MOVE

:ID

:INSERT

:DELETE

:MANUAL

CH 27

CH 28

CH 29

TV OK

Programming a station’s ID

manually:

:MOVE

CH 27

CH 28

CH 29

:ID

:INSERT

:DELETE

:MANUAL

TV OK

:MOVE

Follow the operations below in place of

steps 3 thru 5.

:ID

:INSERT

:DELETE

:MANUAL

2. Press red button.

EDIT

(1) Press the

button repeatedly to

ID CH/CC

-----

2. Press green button.

select a character.

BBC1 CH 21

BBC2 CH 22

ITV CH 23

CH4 CH 24

CH5 CH 25

CH 26

• To cancel the operation, press the

(Information) button.

(2) Press the button to move cursor

to input position.

• Pressing the

cursor backward.

EDIT

button moves the

ID CH/CC

-----

CH 27

CH 28

CH 29

BBC1 CH 21

BBC2 CH 22

ITV CH 23

CH4 CH 24

CH5 CH 25

CH 26

(3) To complete station ID, follow steps

(1) and (2) repeatedly.

TV OK

:LIST

• A station ID can have up to 5

characters.

CH --

CH 27

CH 28

3. Press

to select the

first letter of the desired

station’s ID.

EDIT

TV OK

0 9

ID CH/CC

-----

Note:

BBC1 CH 21

BBC2 CH 22

ITV CH 23

CH4 CH 24

CH5 CH 25

CH 26

• For details on the relationship

between the displayed CH number

and the actual channel number,

see the Channel table on page 25.

CH 27

CH 28

CH 29

3. Press the number buttons

to enter the channel

number.

TV OK

:LIST

• To enter a one-digit channel

number, enter the corresponding

number and press OK button.

4. Press OK.

The ID LIST appears.

EDIT

ID CH/CC

-----

ID LIST

MBC

MCM

MDR

MOVIE

MTV

MTV3

EDIT

ID CH/CC

-----

BBC1 CH 21

BBC2 CH 22

ITV CH 23

CH4 CH 24

CH5 CH 25

CH 26

BBC1 CH 21

BBC2 CH 22

ITV CH 23

CH4 CH 24

CH5 CH 25

CH 26

CH 27

CH 28

CH 29

CH 50

CH 27

CH 28

TV OK

:STORE

TV OK

:MOVE

:ID

:INSERT

:DELETE

:MANUAL

5. Press

to select the

Note:

station ID.

• When you add a station, the station

• To cancel the operation, press the

(Information) button.

preset to PR99 is deleted.

To manually allocate a

station to PR channel

(Manual allocation)

1. Press blue button.

Your TV enters the Manual

allocation mode.

EDIT

ID CH/CC

-----

BBC1 CH 21

BBC2 CH 22

ITV CH 23

CH4 CH 24

CH5 CH 25

CH 26

CH 27

CH 28

CH 29

TV OK

:STORE

:SEARCH+ :FINE+

:SEARCH- :FINE-

2. Press

to select a PR

channel number.

Note:

• PR channel number “AV” appears

on the screen as PR 0 channel.

We recommend that you allocate

this PR channel to a VCR

connected to the aerial socket.

3. Press green or red button

to search for a station.

Scanning stops when the TV

receives a broadcast.

Press green or red button to search

for another station, and keep

searching until you see the station

you want.

If reception is poor:

Press the blue or yellow button to

fine-tune the station.

Note:

• For details on the relationship

between the displayed CH number

and the actual channel number,

see the Channel table on page 25.

4. Press OK.

The station is allocated to a PR

channel.

TROUBLESHOOTING

• If the plug is disconnected from the AC socket, or the TV aerial has problems, you may think there is a problem

with the TV itself. Be sure to check the following before calling for service.

IMPORTANT

• Review all instructions in this manual.

Problem

Action

No power supply.

Insert the plug in an AC socket.

Press the Main power button (see page 8).

■ GENERAL

No picture or sound.

Check aerial connections (see page 6).

Press the number 0 button to select the correct mode (see page 11).

Select the correct colour system manually (see page 13).

The power shuts off

automatically.

Press the Standby button to turn the power on again (see page 8).

Inoperable remote control.

Replace the batteries (see page 4).

Insert the batteries correctly (see page 4).

Use the remote control within about 7 metres of the TV.

Poor colour.

Adjust COLOUR and BRIGHT (see page 13).

Select the correct colour system manually (see page 13).

■ PICTURE

The screen mode suddenly

changed.

The ZOOM mode’s automatic selective function is working

(see page 16).

Lines or streaks in picture

(interference).

Move the components apart until the interference is eliminated.

Reposition the aerial.

Spots (crosstalk).

Reposition the aerial.

Replace with an aerial with better directionality.

Double pictures (ghosts).

Snowy pictures (noise).

Reposition the aerial.

Replace with an aerial with better directionality.

Check aerial connections.

Redirect the aerial.

Replace or repair the aerial.

The screen turns blue.

The BLUE BACK function is on (see page 14).

Disconnect the headphones.

No sound from the TV’s

speakers.

■ SOUND

No stereo sound.

Change STEREO/I•II to

(stereo sound) mode (see page 12).

No “SUB-I” or “SUB-II” sound in

a multisound broadcast.

Change STEREO/I•II to the correct mode (see page 12).

No teletext reception.

Tune to a teletext broadcast channel (see page 17).

We recommend that you not videotape teletext, as it may not be

recorded correctly.

■ TELETEXT

The current time is not

displayed.

Tune to a teletext broadcast channel (see page 14).

The following are normal and are NOT malfunctions:

• When you touch the CRT surface, you might feel a slight charge of static electricity. This is because the CRT contains static

electricity; it does not affect the human body.

• The TV may emit a crackling sound due to a sudden change in temperature. There is no problem unless the picture or

sound is abnormal.

• When a bright a still image (of a white dress, for example) appears on the screen, the image may be coloured. This problem

occurs in all CRTs, and as the bright image disappears, such colouration also disappears.

• This TV is equipped with a microcomputer that may operate abnormally due to interference from external components. If

this happens, turn off the main power and disconnect the power cord from the AC socket. Then reconnect the power cord to

AC socket and turn on the main power again.

Channel table

• The following table shows the relationship between the displayed CH channel number and the actual channel

number.

CH --

Channel

CH --

Channel

CH --

Channel

CH --

Channel

CH 21

CH 22

CH 23

CH 24

CH 25

CH 26

CH 27

CH 28

CH 29

CH 30

CH 31

CH 32

CH 33

E21

E22

E23

E24

E25

E26

E27

E28

E29

E30

E31

E32

E33

CH 34

CH 35

CH 36

CH 37

CH 38

CH 39

CH 40

CH 41

CH 42

CH 43

CH 44

CH 45

CH 46

E34

E35

E36

E37

E38

E39

E40

E41

E42

E43

E44

E45

E46

CH 47

CH 48

CH 49

CH 50

CH 51

CH 52

CH 53

CH 54

CH 55

CH 56

CH 57

CH 58

CH 59

E47

E48

E49

E50

E51

E52

E53

E54

E55

E56

E57

E58

E59

CH 60

CH 61

CH 62

CH 63

CH 64

CH 65

CH 66

CH 67

CH 68

CH 69

E60

E61

E62

E63

E64

E65

E66

E67

E68

E69

SPECIFICATIONS

Model

Item

AV-24WT2EK

AV-28WT2EK

TV RF systems

CCIR I

Colour systems

PAL (NTSC 3.58 / 4.43 MHz only in EXT modes)

E21-E69

Channels and frequencies

Sound-multiplex systems

Teletext systems

NICAM system

Fastext (United Kingdom system) / WST (standard system)

AC 220 – 240 V, 50 Hz

Power requirements

Power consumption

Maximum 136 W,

Maximum 140 W,

Average 111 W, Standby 1.5 W

Average 121 W, Standby 1.5 W

Picture tube size

Visible area 56 cm

Visible area 66 cm

(measured diagonally)

Audio output

Rated Power output 5 W + 5 W

Speakers

3 × 10 cm oval × 2

10 cm round × 2

External input / output

EXT-1, EXT-2

EXT-3

21-pin Euroconnector (SCART)

VIDEO IN (RCA)

AUDIO L / R IN (RCA)

Headphone jack (stereo mini jack, dia. 3.5 mm)

645 mm × 427 mm × 443 mm

23.0 kg

Dimensions (W × H × D)

Weight

716 mm × 489 mm × 496 mm

32.9 kg

Accessories

Remote control unit RM-C794 × 1

AAA (R03) dry cell battery × 2

Design and specifications subject to change without notice.

Pictures displayed on the screen using this TV’s image-processing functions should not be shown for any

commercial or demonstration purpose in public places (tearooms and halls in hotels, etc.) without the consent of

the owners of copyright of the original picture sources, as this constitutes an infringement of copyright.

IBM THINKCENTRE 8421 User Manual
Indesit KT6C3 User Manual
Jaton Geforce 9400 Gt Graphics Card VIDEO498PCITWIN User Manual
JVC CRT Television C 13311 User Manual
LG Electronics Computer Monitor M4210LCBA User Manual
Lucent Technologies MDC 9000 User Manual
Maretron TLM100 User Manual
Pelco PMCS19A User Manual
Philips 21PT2327 User Manual
Philips 107T71 User Manual