JVC 0405TKH CR MU User Manual

AV-32EX5BK  
AV-28EX5BK  
INSTRUCTIONS  
COLOUR TELEVISION  
Trade Mark of the DVB Digital Video Broadcasting  
Project (1991 to 1996) Number: 3533, 3534  
How to move the TV  
When moving the TV, make sure that it is held by two people as shown in the illustration. Be careful  
not to trap your hands when putting the TV down.  
1
2
3
3
Thank you for buying this JVC colour television.  
To make sure you understand how to use your new TV, please read this manual thoroughly before you  
begin.  
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS  
APPLIANCE TO RAIN OR MOISTURE.  
CAUTION:  
• Operate only from the power source specified  
(AC 220 – 240 V, 50 Hz) on the unit.  
• Avoid damaging the AC plug and power cord.  
• When you are not using this unit for a long  
period of time, it is recommended that you  
disconnect the power cord from the main  
outlet.  
• The main power button on the TV does not  
fully isolate the TV from the AC supply. If you  
are not going to use this TV for a long period  
of time, be sure to disconnect the AC plug from  
the AC socket.  
Avoid improper installation and never position the unit where good  
ventilation is unattainable.  
When installing this television, distance recommendations must be  
maintained between the floor and wall, as well as installation in a tightly  
enclosed area or piece of furniture.  
Adhere to the minimum distance guidelines shown for safe operation.  
Failure to heed the following precautions may result in damage to the TV or  
remote control.  
DO NOT block the TV’s ventilation openings or holes.  
(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be  
able to get out.)  
DO NOT place anything on top of the TV.  
(such as cosmetics or medicines, flower vases, potted plants, cups, etc.)  
DO NOT allow objects or liquid into the cabinet openings.  
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)  
DO NOT place any naked flame sources, such as lighted candles, on the TV.  
The surface of the TV screen is easily damaged. Be very careful with it when handling the TV.  
Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully.  
Never use any cleaner or detergent on it.  
In the event of a fault, unplug the unit and call a service technician. Do not attempt to repair it  
yourself or remove the rear cover.  
NOTE:  
Due to static electricity, the TV may be covered with dust.  
If this happens, wipe the TV with a soft cloth being careful not to scratch the TV.  
Digital terrestrial broadcasting (DVB-T) service area  
Although this TV can receive both Digital terrestrial broadcasting (DVB-T) and Analogue terrestrial  
broadcasting, depending on the area in which you live, you may not be able to receive Digital  
terrestrial broadcasting (DVB-T).  
For details of the Digital terrestrial broadcasting (DVB-T) service area, refer to the FREEVIEW  
website etc.  
4
Basic operation ........................................ 36  
COLOUR TEMP....................................... 37  
Connecting the power cord to the AC  
Putting the batteries into the remote  
Turn the Main power on........................... 12  
Basic operations (Remote control) ......14  
Turn the TV on or off from standby mode ... 15  
Operation while watching DTV .............19  
Using the Electronic Programme Guide  
Common Interface ................................... 31  
FEATURES ............................................. 45  
SLEEP TIMER ......................................... 45  
DECODER (EXT-2).................................. 47  
INSTALL.................................................. 48  
AUTO PROGRAM.................................... 48  
EDIT/MANUAL......................................... 49  
ATTENUATOR......................................... 52  
Additional preparation .......................... 53  
Operation while watching analogue  
TV .........................................................32  
Information function ................................. 32  
Connecting the external devices.............. 53  
Operating a JVC brand VCR or DVD  
player.................................................... 55  
CH numbers ........................................... 56  
Troubleshooting .................................... 57  
Specifications ........................................ 60  
Analogue teletext function....................33  
Basic operation ........................................ 33  
Using the List Mode ................................. 34  
Hold.......................................................... 34  
Sub-page ................................................. 34  
Reveal...................................................... 34  
Size.......................................................... 35  
Index ........................................................ 35  
Cancel...................................................... 35  
5
Setting up your TV  
Connecting the aerial  
• The connecting cables are not provided.  
Caution  
• Turn off all the equipment including the TV before connecting anything.  
If you connect via a device with an  
Aerial  
antenna terminal such as a VCR,  
Back of the TV  
follow A B C in the diagram  
75-ohm  
Coaxial  
Cable  
opposite.  
If you connect the antenna  
SERVICE  
directly to the TV, follow 1.  
• To connect more equipment, please see  
“Connecting the external devices” on  
page 53.  
EXT-1  
L
R
• To connect additional audio equipment,  
see “Connecting Speakers/Amplifier” on  
page 55.  
• When receiving Digital terrestrial  
broadcasting (DVB-T), reception can  
suddenly be lost if the signal becomes  
weak. Use a correctly installed high-  
performance antenna.  
• When connecting via a device with an  
antenna terminal such as a VCR, depending  
on the connection method, the signal may  
be weakened. If this happens, use a booster  
to increase the signal strength.  
EXT-2  
AUDIO OUT  
21-pin  
SCART  
Cable  
75-ohm  
Coaxial  
Cable  
To Aerial  
Input  
VCR  
• In areas with a lot of radio communication  
such as near ports or airports, noise may  
be introduced into the picture or sound. In  
such cases, reception may be improved by  
using a high-performance antenna.  
• Read the instruction manual of the  
devices which you connect to the TV.  
To Aerial  
Output  
AV IN/OUT  
Terminal  
CAM (CI) slot  
SERVICE  
Not available  
(For service  
adjustments)  
6
   
Setting up your TV  
To view the pay-per-view of the Connecting the power cord to  
Digital Terrestrial broadcasting the AC outlet  
It is required to subscribe to a pay-per-view  
company to view the pay-per-views of the  
Digital Terrestrial broadcasting.  
Obtain the Conditional Access Module  
(CAM) and the Viewing card by subscribing  
to a pay-per-view company, then insert those  
to the Television using the following  
procedure.  
Insert the AC plug on the power cord from  
the TV into an AC outlet.  
Caution  
• Operate only from the power source specified  
(AC 220 – 240 V, 50 Hz) on the unit.  
1 Switch off the TV and unplug from  
the mains.  
Putting the batteries into the  
remote control  
2 Insert the Viewing Card to the CAM.  
• The Viewing Card should be inserted  
straight into the slot.  
Use two AA/R6 dry cell batteries.  
Insert the batteries from the - end, making  
sure the + and - polarities are correct.  
3 Insert the CAM to the slot of the TV.  
• The CAM should be correctly inserted,  
it is impossible to insert fully if  
reversed. The CAM or the TV terminal  
may be damaged if the CAM is  
forcefully inserted.  
4 Connect the TV to the mains  
supply, switch on, and then wait for  
few moments until the card is  
activated.  
• Follow the warnings printed on the  
batteries.  
• Some CAMs may require the following  
set up.  
Please set the CAM by entering the  
• Battery life is about six months to one  
year, depending on how much you use the  
remote control.  
• The batteries we supply are only for  
setting up and testing your TV, please  
replace them as soon as you need to.  
• If the remote control does not work  
properly, replace the batteries.  
DTV menu, Common Interface then  
pressing  
a
button. (CAM set up  
menu is not displayed when it is not  
required.)  
• To see the viewing contract  
information, press H, Select  
DTV and Press a, then Select  
Common Interface and press a.  
7
     
Setting up your TV  
2 Press the a button  
Initial settings  
The Digital terrestrial broadcasting  
(DVB-T) Automatic Search starts.  
The Digital terrestrial broadcasting  
(DVB-T) channels which can be received  
are automatically registered.  
When the TV is first turned on, it goes into  
the initial settings mode, and you will see the  
JVC logo. Follow the instructions on the  
screen display to make the initial settings.  
• In some parts of the UK, Digital  
terrestrial broadcasting (DVB-T) cannot  
be received.  
If you are in these areas, continue to  
step 4.  
Installation > Automatic Search  
7
buttons  
Channels:  
BBC ONE  
BBC TWO  
BBC THREE  
BBC NEWS 24  
BBCi  
1 Press the Main power button on the  
TV  
CBBC Channel  
The Power lamp lights green and the JVC  
logo is displayed.  
UHF  
CH:68  
100%  
MENU  
Cancel, go to Installation  
Cancel, go to DTV  
BACK  
D0201-EN  
When the Automatic Search has  
finished, the EDIT PR LIST menu  
appears  
Main power  
button  
Power lamp  
EDIT PR LIST  
1
BBC ONE  
• If the JVC logo does not appear this is  
because your TV has already been  
turned on for the first time:  
1. BBC ONE  
2. BBC TWO  
7. BBC THREE  
30. CBBC Channel  
40. BBC NEWS 24  
51. BBCi  
Perform the initial settings with  
“Installation” (see page 30) in the  
DTV menu and “AUTO PROGRAM”  
(see page 48) in the INSTALL menu.  
Select  
Delete  
Edit Name  
Lock  
Favourites  
More..  
Select function  
Select PR OK Watch PR  
D0202-EN  
• If you want to, you can now edit the  
programme numbers (PR) using the  
EDIT PR LIST function. For details,  
see “Edit PR List” on page 28.  
• If you do not want to edit programme  
numbers (PR), go to the next step.  
8
 
Setting up your TV  
3 Press the H button  
4 Press the a button to display the  
T-V LINK menu  
The Analogue terrestrial broadcasting  
AUTO PROGRAM starts.  
T-V LINK  
The AUTO PROGRAM menu appears  
and received TV channels are  
automatically stored in the programme  
numbers (PR).  
DOWNLOAD TV  
RECORDING DEVICE  
OK  
EXIT  
AUTO PROGRAM  
D0005-EN  
CH 10  
• If you do not have a T-V LINK  
compatible VCR connected:  
Press the TV/DTV button to exit the T-V  
LINK menu.  
20%  
OK  
The T-V LINK menu disappears.  
D5004-EN  
• To cancel the AUTO PROGRAM  
function:  
Press the TV/DTV button.  
If you have a T-V LINK compatible  
VCR connected to the EXT-2  
terminal:  
Follow the operating procedure  
“Downloading the data to VCR” on  
page 10 to transmit the Programme  
number (PR) data.  
After the AUTO PROGRAM has  
finished, the EDIT menu appears  
Now, the initial settings are complete,  
and you can watch the TV  
EDIT  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
21  
22  
23  
24  
25  
26  
27  
28  
29  
• The Analogue terrestrial broadcasting  
channels BBC1, BBC2, ITV, Channel 4  
and Channel 5 are automatically set to the  
programme numbers PR1 to PR5. If the  
TV doesn’t receive one of these TV  
channels, that programme number (PR)  
will not be set. Programme number PR6 is  
not normally set.  
ID  
MANUAL  
OK  
MOVE  
INSERT DELETE  
D0038-EN  
• The AUTO PROGRAM function does not  
set the programme number PR 0 (AV) for  
your video cassette recorder. You will  
need to set this using the MANUAL  
function.  
• If you want to, you can now edit the  
programme numbers (PR) using the  
EDIT/MANUAL function. For details,  
see “EDIT/MANUAL” on page 49.  
• If you do not want to edit programme  
numbers (PR), go to the next step.  
If you have any problems setting up your  
new TV, please call the  
Helpline on 0870 330 5000.  
9
Setting up your TV  
Downloading the data to VCR  
You can transmit to the latest Analogue  
terrestrial broadcasting Programme numbers  
(PR) data to a VCR with the T-V LINK  
function.  
T-V LINK functions  
When you have a T-V LINK compatible  
VCR connected to the EXT-2 Terminal on  
the TV, it is easier to set up the VCR and to  
view videos. T-V LINK uses the following  
features:  
• This only works when a T-V LINK  
compatible VCR is connected to the  
EXT-2 terminal.  
To use T-V LINK functions:  
A “T-V LINK compatible VCR” means a  
JVC video cassette recorder with the T-V  
LINK logo, or with one of the following  
logos. However, these VCRs may support  
some or all of the features described earlier.  
For details, see your VCR instruction  
manual.  
• This only works when the T-V LINK  
menu is being displayed.  
T-V LINK  
DOWNLOAD TV  
RECORDING DEVICE  
OK  
EXIT  
D0005-EN  
“Q-LINK” (a trademark of Panasonic  
Corporation)  
“Data Logic” (a trademark of Metz  
Corporation)  
“Easy Link” (a trademark of Phillips  
Corporation)  
“Megalogic” (a trademark of Grundig  
Corporation)  
1 Turn on the VCR  
2 Press the a button  
The data transmission begins.  
TV  
RECORDING DEVICE  
TRANSFER. . . . .  
D0037-EN  
“SMARTLINK” (a trademark of Sony  
Corporation).  
The T-V LINK menu disappears once the  
data transmission ends.  
Pre-set download  
When the T-V LINK menu is  
changed over to another menu:  
The TV has finished its menu. This new  
menu is operated from the VCR. See the  
VCR instruction manual for what to do  
next.  
The VCR will automatically download the  
registered data on the TV Analogue  
terrestrial broadcasting channels from the  
TV. This means you do not need to set up the  
program channels on your VCR manually.  
The preset download function automatically  
begins when the initial setting is complete or  
whenever you carry out the AUTO  
If “FEATURE NOT AVAILABLE”  
appears at the T-V LINK menu:  
Check the following three items. Then  
press the 2 button to retry data  
transmission.  
• Has a T-V LINK compatible VCR  
been connected to the EXT-2  
terminal?  
PROGRAM or EDIT/MANUAL functions.  
You can also carry out this function using  
your VCR controls.  
When “FEATURE NOT AVAILABLE” is  
displayed:  
• Has the VCR power been turned on?  
• Does the SCART cable that is  
connected to the EXT-2 terminal to T-  
V LINK compatible VCR have all its  
proper connections?  
If “FEATURE NOT AVAILABLE” is  
displayed, the download was not performed  
correctly. Before trying to download again,  
check that:  
• the VCR power is turned on  
• the VCR is T-V LINK compatible  
• the VCR is connected to the EXT-2  
terminal  
• the SCART cable is fully wired.  
10  
   
Setting up your TV  
When the VCR is not ready, the following  
messages are displayed.  
Direct Rec  
“What You See Is What You Record”  
You can easily record to VCR the images  
that you are watching on the TV.  
ERROR  
MESSAGE  
Cause and  
countermeasure  
For details, read the manual for your VCR.  
Use your VCR controls. “DEVICE IS  
RECORDING” is displayed.  
NO  
The VCR is not able to  
RECORDING record.  
Check the VCR.  
NO  
The RECORDING DEVICE  
You cannot carry out Direct Rec using your  
TV’s control.  
RECORDING, is not ready to record. Check  
MEDIA  
PROBLEM  
the VCR tape.  
Generally, the VCR cannot record a TV  
channel that it cannot receive properly on its  
own tuner, even if you can view that TV  
channel on the TV. However, some VCRs  
can record a TV channel by using the TV’s  
output if that channel can be viewed on the  
TV. For details, see your VCR instruction  
manual.  
NO  
The RECORDING DEVICE  
RECORDING, cannot record as it is  
DEVICE BUSY recording or playing. Check  
the VCR.  
Refer to the VCR instruction manual.  
TV Auto Power On/VCR Image  
View  
Do not turn the TV off in the following  
cases.  
When the VCR starts playing, the TV  
automatically turns on and the images from  
EXT-2 terminal are displayed on the screen.  
When the VCR menu is operated, the TV  
automatically turns on and the images from  
EXT-2 terminal are displayed on the screen.  
• This function does not operate if your  
TV’s main power is turned off. Set your  
TV’s main power to on (standby mode).  
• when recording images from an external  
device connected to the TV (for example  
a camcorder)  
• when recording a TV channel after it has  
been unscrambled on a decoder  
• when recording a TV channel by using the  
TV’s output because the VCR’s own  
tuner cannot properly receive that  
channel.  
• when recording Digital terrestrial  
broadcasting (DVB-T).  
If you change channels or perform  
other operations while a Digital  
terrestrial broadcasting (DVB-T)  
channel is being recorded, a window  
appears asking whether to stop the  
recording.  
Press the a button to stop the  
recording, or the TV/DTV button to  
continue the recording.  
11  
 
Basic operations (TV)  
Turn the Main power on  
Press the Main power button on the  
TV.  
The Power lamp lights red and your TV is in  
the standby mode.  
• If the power lamp lights green, the TV is  
already on.  
To turn the Main power off:  
Press the Main power button again.  
The Power lamp goes off.  
Caution  
• The main power button on the TV does  
not fully isolate the TV from the AC  
supply. If you are not going to use this TV  
for a long period of time, be sure to  
disconnect the AC plug from the AC  
socket.  
Turn the TV on from standby  
mode  
Press the P p buttons to turn the TV  
on from standby mode  
S
R
L/MONO  
EXT-3  
P
When the TV is turned on, the power lamp  
changes from red to green.  
Power lamp condition  
S
R
L/MONO  
Power lamp  
condition  
Status  
EXT-3  
P
normal  
Green  
when timer is set Green  
3 minutes before Flashing in green  
timer starts  
On  
while timer  
recording in  
progress  
Green  
Refer to the pages in parentheses for details.  
1 Main power button (8, 12)  
2 Power lamp (8, 12)  
3 Remote control sensor  
4 r (Volume) button (13)  
5 P p buttons/ q buttons (13)  
6 Headphone jack (mini jack) (53)  
7 EXT-3 terminal (43, 53)  
normal  
Red  
when timer is set Red  
3 minutes before Flashing in Red  
timer starts  
Standby  
while timer  
recording in  
progress  
Orange  
12  
     
Basic operations (TV)  
Choose a TV channel  
Press the P p buttons to choose a  
programme number (PR) or an EXT  
terminal  
The EXT terminal cannot be chosen when  
watching Digital terrestrial broadcasting  
(DVB-T).  
Switching between Digital  
terrestrial broadcasting (DVB-T)  
and Analogue terrestrial  
broadcasting.  
1 Press the r (Volume) button once  
The volume level indicator appears.  
2 Press the r (Volume) button  
while the volume level indicator is  
displayed  
Adjust the volume  
1 Press the r (Volume) button once  
The volume level indicator appears.  
2 Press the q buttons while the  
volume level indicator is displayed  
13  
   
Basic operations (Remote control)  
1 Muting button  
2 Number buttons  
3 Information button  
4 Colour button  
1
2
~
!
5 TV/DTV button  
6 7 buttons  
7 g (Text) button  
8 p p buttons  
9 VCR/DVD/Teletext control buttons  
0 p buttons  
- c button  
3
4
5
@
= i (3D CINEMA SOUND) button  
~ # (Standby) button  
! VCR/TV/DVD switch  
@ G button  
# H button  
$ a button  
#
$
% b button  
^ r (Volume) q buttons  
& GUIDE button  
* SUBTITLE button  
6
7
%
^
8
9
0
&
*
-
=
14  
 
Basic operations (Remote control)  
Use the p p buttons:  
Turn the TV on or off from  
standby mode  
Press the p p buttons to  
choose the programme number  
(PR) you want.  
• For Digital terrestrial broadcasting (DVB-  
T), if the FAVOURITE setting in the  
“Edit PR List” (see page 28) has been set,  
only that programme number (PR) can be  
chosen.  
Press the # (standby) button to turn  
the TV on or off.  
When the TV is turned on, the power lamp  
lights green.  
• The power can be turned on by pressing  
the TV/DTV button, p p buttons or  
Number buttons.  
• For Analogue terrestrial broadcasting, an  
EXT terminal can also be chosen.  
To turn the TV on or off, set the VCR/TV/  
DVD switch on the remote control to the  
TV position and press the # button.  
If the VCR/TV/DVD switch on the remote  
control is set to a position other than TV,  
the TV will not be turned on or off even if  
the # button is pressed.  
Use the AV button:  
Press the AV button to choose an  
EXT terminal.  
TV mode  
EXT modes  
Analogue  
terrestrial  
broadcasting  
EXT-2  
E1  
E2  
S2  
or  
Choose a TV channel and  
watch images from external  
devices  
Digital  
terrestrial  
broadcasting  
(DVB-T)  
EXT-3  
S3  
E3  
or  
Switching between Digital  
terrestrial broadcasting (DVB-T)  
and Analogue terrestrial  
broadcasting.  
• You can choose a video input signal from  
the S-VIDEO signal (Y/C signal) and  
regular video signal (composite signal).  
For details, see “S-IN (S-VIDEO input)”  
on page 43.  
• If you do not have a clear picture or no  
colour appears, change the colour system  
manually. See “COLOUR SYSTEM” on  
page 39.  
• If you choose an EXT terminal with no  
input signal, the EXT terminal number  
becomes fixed on the screen.  
• This TV set has a function which can  
automatically change over the input  
according to a special signal output from  
an external device. (The EXT-3 terminal  
does not support this function.)  
Press the TV/DTV button.  
The broadcasting is switched every time the  
button is pressed.  
Use the number buttons:  
Enter the programme number (PR)  
of the channel using the number  
buttons.  
Example:  
• PR 6 press 6  
• PR 12 press 1 and 2  
• PR 123 press 1, 2 and 3  
15  
   
Basic operations (Remote control)  
To return to a TV channel:  
Press the TV/DTV button, the p p  
buttons or the number buttons.  
Adjust the volume  
Press the r q buttons to adjust  
the volume.  
The volume level indicator appears and the  
volume changes as you press the r q  
buttons.  
To use the programme number PR 0  
(AV):  
When the TV and VCR are connected only  
by the aerial cable, choosing the programme  
number PR 0 (AV) allows you to view  
images from the VCR. Set the VCR RF  
channel to the programme number PR 0  
(AV) manually. For details, see “EDIT/  
MANUAL” on page 49.  
Muting the sound  
Press the (muting) button to  
l
turn off the sound.  
Pressing the (muting) button again  
l
Pressing the G button changes the choice as  
follows:  
restores the previous volume level.  
TV mode  
Analogue  
terrestrial  
EXT modes  
EXT-2  
EXT-1  
ZOOM function  
You can change the screen size according to  
the picture aspect ratio. Choose the optimum  
one from the following ZOOM modes.  
PR 0  
broadcasting  
E2  
S2  
or  
E1  
AUTO:  
When a WSS (Wide Screen Signalling)  
signal, which shows the aspect ratio of the  
picture, is included in the broadcast signal or  
the signal from an external device, the TV  
automatically changes the ZOOM mode to  
16:9 ZOOM mode or FULL mode according  
to the WSS signal.  
If a WSS signal is not included, the picture is  
displayed according to the ZOOM mode set  
with the 4:3 AUTO ASPECT function.  
• For details of the 4:3 AUTO ASPECT  
function, see “4:3 AUTO ASPECT” on  
page 40.  
Digital terrestrial  
broadcasting  
(DVB-T)  
EXT-3  
or S3  
E3  
• The VCR sends its playback image along  
the aerial cable as an RF (radio frequency)  
signal.  
• Also see your VCR instruction manual.  
• When the AUTO (WSS) mode does not  
function correctly due to poor WSS signal  
quality or when you want to change the  
ZOOM mode, press the c button  
and change to another ZOOM mode.  
• When watching a 16:9 FULL programme  
with Digital terrestrial broadcasting  
(DVB-T), the aspect ratio is FULL.  
REGULAR:  
Use to view a normal picture (4:3 aspect  
ratio) as this is its original shape.  
16  
   
Basic operations (Remote control)  
Choose the ZOOM mode  
PANORAMIC:  
This stretches the left and right sides of a  
normal picture (4:3 aspect ratio) to fill the  
screen, without making the picture appear  
unnatural.  
1 Press the c button to display  
the ZOOM menu  
ZOOM  
AUTO  
REGULAR  
PANORAMIC  
14:9 ZOOM  
16:9 ZOOM  
16:9 ZOOM SUBTITLE  
FULL  
“This mode may result in information such as  
headlines or rolling text at the very top or  
bottom of the screen not being fully viewable  
on some programmes.  
OK  
D0009-EN  
In such cases the picture can be moved up or  
down using 6 keys, alternatively switch to  
FULL mode.”  
2 Press the 6 buttons to choose a  
ZOOM mode. Then press the a  
button  
14:9 ZOOM:  
This zooms up the wide picture (14:9 aspect  
ratio) to the upper and lower limits of the  
screen.  
The picture expands and the chosen  
ZOOM mode is displayed in about 5  
seconds.  
• The ZOOM mode may be  
automatically changed by the control  
signal from an external device. When  
you want to return to the previous  
ZOOM mode, choose the ZOOM  
mode again.  
16:9 ZOOM:  
This zooms up the wide picture (16:9 aspect  
ratio) to the full screen.  
Adjusting the visible area of the  
picture  
16:9 ZOOM SUBTITLE:  
This zooms up the wide picture (16:9 aspect  
ratio) with subtitles to the full screen.  
If subtitles or the top (or bottom) of the  
picture are cut off, you can adjust the visible  
area of the picture manually.  
1 Press the c button  
The ZOOM menu appears.  
FULL:  
This uniformly stretches the left and right  
sides of a normal picture (4:3 aspect ratio) to  
fill the wide TV screen.  
2 Press the a button to display the  
ZOOM mode indicator  
The indicator appears.  
• For 16:9 aspect ratio pictures that have  
been squeezed into a normal picture (4:3  
aspect ratio), use the FULL mode to  
restore the picture to its original shape.  
3 While it is displayed, press the 6  
buttons to change the position of  
the picture  
• You cannot adjust the visible area in  
REGULAR or FULL mode.  
• When you use this TV’s output signal to  
record a Digital terrestrial broadcasting  
(DVB-T) 16:9 broadcast, it will be  
recorded with its picture squeezed into a  
4:3 aspect ratio picture.  
Use the FULL mode to restore the picture  
to its original shape when playing the  
recording.  
17  
Basic operations (Remote control)  
• The visible area adjustment is saved even  
after the TV channel is changed.  
However, it is cancelled if the following  
operations are performed.  
– The power is turned off/on  
– The ZOOM mode is changed  
– The g (Text) button is pressed  
– The TV is switched between TV mode  
and EXT mode  
• Some menu displays can be cut off when  
you move the visible area up or down  
while watching Digital terrestrial  
broadcasting (DVB-T).  
3D CINEMA SOUND function  
You can enjoy sounds with a wider  
ambience.  
Press the / (3D CINEMA SOUND)  
button to turn the 3D CINEMA SOUND  
function on or off  
• The 3D CINEMA SOUND effect can be  
adjusted with the “3D CINEMA  
SOUND” menu (see page 42).  
• The 3D CINEMA SOUND function does  
not work properly with mono sound.  
• If the audio is mono sound, use “HYPER  
SOUND” (see page 41) to enjoy a  
simulated stereo experience.  
• When 3D CINEMA SOUND is turned on,  
HYPER SOUND turns off, and when  
HYPER SOUND is turned on, 3D  
CINEMA SOUND turns off.  
18  
 
Operation while watching DTV  
Information function  
Using the Electronic  
Programme Guide (EPG)  
When the h (Information) button is pressed,  
the programme information appears for  
approximately 1 minute.  
The EPG screen appears when the GUIDE  
button is pressed while watching Digital  
terrestrial broadcasting (DVB-T).  
ITV News  
CH61  
41  
Now: 13:00-14:00 Steve Scott  
Next: 14:00-14:30 Steve Scott  
13:19  
1
2
3
D0203-EN  
• When the h (Information) button is  
pressed while the information is being  
displayed, the information disappears.  
Electronic Programme Guide  
06:02  
06:00-Breakfast  
20/10/2005  
GENRE All  
20/10  
21/10  
22/10  
1. BBC ONE  
2. BBC TWO  
7. BBC THREE  
09:15-Animal Park  
10:00-Escape to the Country  
11:00-Trading Up  
23/10 30. CBBC Channel  
24/10 40. BBC NEWS 24  
25/10 51. BBCi  
• The time display in the programme  
information uses the time information  
which is included in the Digital terrestrial  
broadcasting (DVB-T). Depending on the  
channel, the time information may not be  
correct.  
11:30-Car Booty  
12:00-Bargain Hunt  
12:30-Eggheads  
27/10 90. BBC R n Gaidheal 13:00-BBC News  
26/10 89. BBC R Scotland  
.
06:00 09:15 Breakfast  
Start your day with all the latest news,sport,business and weather  
from the BBC`s Breakfast team.Includes Reporting Scotland at 25  
and 55 minutes past each hour.  
Select PR  
Genre  
Scroll  
More..  
D0204-EN  
4
1 Date column  
2 Channel column  
3 Programme column  
4 Brief description of programme  
The programme name, broadcast time and  
a brief description of the programme are  
displayed for the programme chosen from  
the date column, channel column and  
pogramme column.  
Press the h (Information) button to display  
the help screen. Press it again to return to the  
EPG screen.  
Electronic Programme Guide  
GENRE All  
06:06  
20/10/2005  
20/10  
21/10  
22/10  
1. BBC ONE  
2. BBC TWO  
7. BBC THREE  
03:25-BBC News 24  
06:00-Breakfast  
09:15-Animal Park  
10:00-Escape to the Country  
11:00-Trading Up  
23/10 30. CBBC Channel  
24/10 40. BBC NEWS 24  
25/10 51. BBCi  
11:30-Car Booty  
DTV:Go to DTV  
MENU  
Guide:Leave guide  
Back:Go to previous  
OK  
i:Exit help  
More..  
D0205-EN  
Help screen  
19  
     
Operation while watching DTV  
When the TV is being watched, it  
Using the Set Reminder  
automatically changes to the channel of the  
scheduled programme when the start time of  
the scheduled program is reached.  
• The scheduling function does not work  
when the TV is turned off.  
When you schedule a programme, you will  
not miss a programme that you want to watch.  
1 Press the 6 buttons and choose  
the date from the Date column  
Cancelling a scheduled programme.  
Display the EPG screen, choose a  
programme which has the scheduled icon  
2 Press the 6 buttons and choose  
the channel from the Channel  
column  
(
), and press the a button.  
The list of programme names and the  
broadcast time of the chosen date appears  
on the Programme column.  
The icon disappears and the scheduling is  
cancelled.  
Using the Rec Timer  
3 3 Press the 6 buttons and  
choose the program that you want  
to schedule from the Programme  
column  
By setting the Rec Timer, you can record a  
Digital terrestrial broadcasting (DVB-T)  
programme with a VCR connected to EXT-2.  
1 Perform steps 1 ~ 3 of the “Using  
the Set Reminder”  
The brief description of the programme  
are displayed.  
• Press the yellow and blue buttons to  
scroll the channel column.  
2 Press the red button  
The timer setting window appears.  
4 Press the a button  
REC TIMER  
13:49  
15/10/2005  
No. Name  
Start End  
Date  
Mode  
The scheduled icon appears at the right of  
the chosen programme and the scheduling  
is completed.  
1
2
3
4
5
BBC ONE  
BBC ONE  
BBC ONE  
BBC ONE  
BBC ONE  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
Scheduled icon  
Name  
BBC ONE  
Start  
End  
Electronic Programme Guide  
GENRE All  
06:02  
20/10/2005  
Date  
Mode  
01/01/2004  
Once  
20/10  
21/10  
22/10  
1. BBC ONE  
2. BBC TWO  
7. BBC THREE  
06:00-Breakfast  
09:15-Animal Park  
10:00-Escape to the Country  
11:00-Trading Up  
Select Programme OK Confirm Timer BACKCancel  
More..  
23/10 30. CBBC Channel  
24/10 40. BBC NEWS 24  
25/10 51. BBCi  
D0211-EN  
11:30-Car Booty  
12:00-Bargain Hunt  
12:30-Eggheads  
27/10 90. BBC R n Gaidheal 13:00-BBC News  
26/10 89. BBC R Scotland  
3 Proceed to step 2 of the “Rec  
Timer” (page 23)  
• If “Maximum number of timers  
exceeded” is displayed, the memory is  
full.  
.
06:00 09:15 Breakfast  
Start your day with all the latest news,sport,business and weather  
from the BBC`s Breakfast team.Includes Reporting Scotland at 25  
and 55 minutes past each hour.  
Select PR  
Genre  
Scroll  
More..  
• Steps 1 to 4 can be repeated to schedule  
more programmes.  
• When the GUIDE, TV/DTV, H or  
b buttons are pressed, the EPG  
screen disappears and the normal screen  
returns.  
• When the GUIDE, TV/DTV, H or  
b buttons are pressed, the EPG  
screen disappears and the normal screen  
returns.  
• When the “Rec Timer” is set within the  
same period of time, the “Set Reminder”  
will be cancelled.  
• For more information, see “Rec Timer”  
on page 23.  
20  
Operation while watching DTV  
Using the Genre function  
By using the Genre function you can sort  
programmes by genre.  
1 Press the green button  
The Genre window appears.  
2 Press the 6 buttons and choose  
the genre  
3 Press the a button  
The selected genre programme appears on  
the Programme column.  
Cancelling the Genre function.  
Display the Genre window and choose “All”  
for the genre.  
Programmes of every genre appears on the  
Programme column.  
Displaying the Subtitles  
With Digital terrestrial broadcasting (DVB-  
T), some programmes are broadcast with  
subtitles. Subtitles can be displayed when  
watching these programmes.  
Press the SUBTITLE button when  
watching Digital terrestrial  
broadcasting (DVB-T)  
“Subtitle ON” appears at the top-left of the  
screen and, when the programme has  
subtitles, the subtitles are displayed.  
Subtitle ON  
D0207-EN  
• When the SUBTITLE button is pressed  
again, “Subtitle OFF” appears and the  
subtitles disappear.  
21  
 
Digital Teletext function  
1 Press the g button  
The digital teletext information appears.  
BBC ONE  
Powers  
For a full list of sections,  
press SELECT  
VCR/TV/  
DVD switch  
Contact info  
CBeebies Home  
Music  
Number  
buttons  
Taking Care  
NEWS  
SPORT  
WEATHER  
MAIN MENU  
Press TEXT to exit  
B
B
C
Colour  
buttons  
D0208-EN  
2 Operate it with the colour buttons,  
7 buttons and a button  
The operation method may differ depending  
on the contents of the digital teletext.  
Follow the instructions displayed on digital  
teletext screen.  
7
buttons  
• When “Press SELECT” or similar  
message appears on the screen, press  
the a button.  
• When the g (Text) button is pressed, the  
TV returns to television broadcasting.  
• With Digital terrestrial broadcasting  
(DVB-T), in addition to digital teletext  
broadcasting at the same time as normal  
broadcasting, there are also channels with  
just digital teletext broadcasting.  
• The aspect ratio when watching a channel  
with just digital teletext broadcasting is  
the same as the aspect ratio of the picture  
watched previously.  
With Digital terrestrial broadcasting (DVB-  
T), in addition to pictures and sound, you can  
also watch digital teletext.  
• When you press the g (Text) button  
while subtitles are on, the subtitles are  
turned off. When you press the g (Text)  
button again, the digital teletext screen is  
displayed.  
Digital teletext is sometimes broadcast at the  
same time as normal broadcasting.  
22  
 
Operation with the DTV menu  
Buttons used to operate the menus  
Rec Timer  
By setting the timer, you can record a Digital  
terrestrial broadcasting (DVB-T) programme  
with a VCR connected to EXT-2 while you  
are out.  
TV/DTV  
• Before using DTV timer recording, the  
VCR and TV must be connected up  
correctly. For details, see “Connection  
when recording to VCR” on page 54.  
• When you have a T-V LINK compatible  
VCR connected to EXT-2, all you need to  
do is set the TV timer settings and the  
programme will be recorded.  
By using “Direct Rec” of the T-V LINK  
function, the Direct Rec commands are sent  
from the TV to the VCR to automatically  
start and end the recording. It is not  
necessary to set the timer on the VCR.  
• When your VCR is not T-V LINK  
compatible, you also need to set the VCR  
timer settings to match the TV timer  
settings.  
• The recording may not start and stop at  
exactly the right times for some  
programmes. It is recommended that you  
allow some leeway when setting the  
recording times.  
• Provided that the days and times are not  
the same, you can set up to five timer  
settings.  
• When subtitles are ON, the subtitles  
displayed with the broadcast will be  
recorded. When you do not want to record  
the subtitles, you need turn OFF the  
Subtitle setting beforehand (See  
Displaying the DTV menu  
1 Press the H button to display  
the MENU (main menu)  
MENU  
PICTURE SETTING  
PICTURE FEATURES  
SOUND SETTING  
EXT SETTING  
FEATURES  
INSTALL  
3D CINEMA SOUND  
DTV  
OK  
D5105-EN  
• DTV in the menu bar can only be chosen  
when watching Digital terrestrial  
broadcasting (DVB-T).  
2 Press the 7 buttons to  
choose the DTV  
3 Press the a button  
The DTV menu appears.  
DTV  
Rec Timer  
Configuration  
Edit PR List  
Installation  
“Displaying the Subtitles” on page 21.).  
• During DTV timer recording, you are  
unable to view the EXT SETTING menu,  
INSTALL menu, or DTV menu.  
Common Interface  
D0209-EN  
4 Press the 6 buttons to choose  
the item  
• Press the b button to return to  
the previous menu.  
• Press the TV/DTV or H button  
to exit from the menu.  
• For menu items other than DTV, see  
page 36.  
23  
     
Operation with the DTV menu  
End:  
1 Choose Timers and press the a  
button  
Set the timer end time with the number  
buttons.  
• When the 5 buttons are pressed, the  
input position moves.  
The TIMER menu appears.  
REC TIMER  
13:48  
15/10/2005  
Mode  
No. Name  
Start End  
Date  
1
2
3
4
5
6
7
8
9
10  
BBC ONE  
BBC ONE  
BBC ONE  
BBC ONE  
BBC ONE  
BBC ONE  
BBC ONE  
BBC ONE  
BBC ONE  
BBC ONE  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
Press the 4 button.  
Date:  
Set the date for the timer to work with the  
number buttons.  
• When the 5 buttons are pressed, the  
input position moves.  
Change Mode OK Edit timer settings  
More..  
Press the 4 button.  
D0210-EN  
Mode:  
Use the 5 buttons to choose the timer  
mode (Once/Daily/Weekly), and then  
press the a button.  
• When the h (Information) button is  
pressed, the help screen appears. When  
it is pressed again, the previous screen  
is returned to.  
4 Prepare your VCR for recording  
When recording on a T-V LINK  
compatible VCR:  
2 Press 6 buttons to choose the  
timer number, and then press the  
a button  
1. Insert the videotape for recording into  
the VCR and set the recording mode.  
2. Make sure the VCR is ready to  
receive Direct Rec commands from  
the TV.  
The timer setting window appears.  
REC TIMER  
13:49  
15/10/2005  
No. Name  
Start End  
Date  
Mode  
1
2
3
4
5
BBC ONE  
BBC ONE  
BBC ONE  
BBC ONE  
BBC ONE  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
00:00 00:00 01/01/2000 Inactive  
• Make sure other VCR timer settings  
do not coincide with the TV timer  
settings.  
• For details, see your VCR  
instruction manual.  
Name  
BBC ONE  
Start  
End  
Date  
Mode  
01/01/2004  
Once  
Select Programme OK Confirm Timer BACKCancel  
More..  
When recording on a T-V LINK  
incompatible VCR:  
D0211-EN  
1. Insert the videotape for recording into  
the VCR and set the recording mode.  
2. Set the VCR recording timer settings.  
• Make the start and end time match  
that of the TV timer.  
3 Use the 7 buttons, number  
buttons and a button to set the  
timer  
• When setting the start time and end  
time, input 1200 for 12:00 PM, 1500  
for 3:00 PM and 0000 for 12:00 AM.  
• Set the VCR to record the signal  
from the external input that the TV  
is connected to.  
Name:  
Use the 5 buttons to choose the  
channel for which the timer is to be set.  
• For details, see your VCR  
instruction manual.  
Press the 4 button.  
Start:  
When you have finished Step 4, you have set  
the timer.  
Set the timer start time with the number  
buttons.  
• When the 5 buttons are pressed, the  
input position moves.  
When you are not watching TV, make sure  
the TV is in standby.  
Press the 4 button.  
24  
 
Operation with the DTV menu  
The TV power lamp begins flashing at three  
minutes before the timer start time. If you are  
watching TV at the time, a message appears  
on the screen to inform you the timer is about  
to start.  
lights orange while timer recording is in  
progress.  
Reactivating the cancelled timer  
setting  
Display the TIMER MENU and press the  
6 buttons to choose which timer  
setting to reactivate. Press the 5  
buttons so that “Active” appears in the  
Mode column.  
Aborting timer recording  
Display the Digital terrestrial broadcasting  
• When performing timer recording with a  
T-V LINK compatible recording device,  
test the timer recording before you record  
the programme. There are some T-V  
LINK compatible recording device that  
will not correctly receive the Direct Rec  
command from the TV.  
press the  
(Information) button. A  
h
window will appear asking if you want to  
stop the recording. Press the button to  
a
abort the recording. If you want to continue  
recording, press the TV/DTV button.  
In this case, follow the instructions of  
“When recording on a T-V LINK  
incompatible VCR:”.  
• If, while attempting to perform timer  
VCR, the TV timer operation starts but  
the VCR does not start recording, the  
problem is with the VCR. Resolve the  
VCR-related problem and see  
“Aborting timer recording” to abort  
the recording. After this is done, reset  
the timer.  
• When you are watching TV at the  
recording start time, you may see an  
error message stating that recording  
could not start because of a VCR-  
related problem. See “Direct Rec” on  
page 11, which lists and explains each  
error message.  
While the timer is in operation:  
• You can turn the TV on or off (Standby).  
WARNING: Do not turn off the main  
power.  
• You can watch Analogue terrestrial  
broadcasting channels or the pictures via  
an EXT terminal.  
• Please note that any programme  
information that appears on the screen,  
such as when making changes to the  
Digital terrestrial broadcasting (DVB-T)  
channel picture, will be superimposed  
over the picture in the VCR recording.  
• You cannot change Digital terrestrial  
broadcasting (DVB-T) channels while  
recording.  
Cancelling and resetting the timer  
setting:  
Cancelling the timer setting  
Display the TIMER MENU and press the  
6 buttons to choose which timer  
setting to cancel. Press the 5 buttons  
so that “Inactive” appears in the Mode  
column.  
25  
 
Operation with the DTV menu  
Subtitle language  
Configuration  
With Digital terrestrial broadcasting (DVB-  
T), a number of subtitles can be broadcast at  
the same time. Choose the subtitle you want  
to display when watching these broadcasts.  
Set the basic setting for watching Digital  
terrestrial broadcasting (DVB-T).  
Choose configuration and press the  
a button  
CONFIGURATION appears.  
1 Press the 6 buttons and choose  
Subtitle  
CONFIGURATION  
2 Press the 5 buttons and choose  
a subtitle language that appears  
when the SUBTITLE button is  
pressed  
Audio Language  
Subtitle  
English  
English  
Off  
Favourite Mode  
Receiver Upgrade  
Enter PIN code  
V.3.3  
The subtitle language changes every time  
the button is pressed.  
Favourite Mode  
Enable/disable the Edit PR List Favourites  
settings.  
Change preferred audio language  
More..  
D0212-EN  
1 Press the 6 buttons and choose  
• When the b button is pressed, the  
previous screen is returned to. When the  
TV/DTV or H buttons are pressed,  
the menu disappears.  
• When the h (Information) button is  
pressed, the help screen appears. When it  
is pressed again, the previous screen is  
returned to.  
Favourite Mode  
2 Press the 5 buttons and choose  
ON or OFF  
On:  
The Edit PR List Favourites settings are  
enabled.  
When the p p button is pressed, only  
the channels chosen in the Edit PR List  
Favourites (those with the icon) can be  
chosen.  
• For details on how to set your  
favourite channels, see “Setting the  
favourite channels” on page 30.  
Audio Language  
With Digital terrestrial broadcasting (DVB-  
T), a number of languages can be broadcast  
at the same time. Choose the language you  
want to listen to when watching these  
broadcasts.  
Off:  
1 Press the 6 buttons and choose  
The Edit PR List Favourites settings are  
disabled  
Audio Language  
When the p p button is pressed, all the  
channels registered in the Edit PR List can  
be chosen.  
2 Press the 5 buttons and choose  
the language  
The language changes every time the  
button is pressed.  
• If the selected language is not broadcast,  
the default language will be played.  
26  
 
Operation with the DTV menu  
Receiver Upgrade  
Set the method to upgrade the Digital  
terrestrial broadcasting (DVB-T) receiver  
software.  
In the future, there is a possibility that the  
Receiver Update function may also be able to  
be used to update the Digital terrestrial  
broadcasting (DVB-T) software and add new  
functions.  
1 Press the 6 buttons and choose  
Receiver Upgrade, and press the  
a button  
Enter PIN code  
The setting window appears.  
Choose Enter PIN code to change the PIN  
code for the Edit PR List menu’s “Lock”.  
The PIN code factory setting (how it is set  
when you purchase the television) is 0000.  
CONFIGURATION  
Audio Language  
Subtitle  
English  
English  
Off  
Favourite Mode  
Receiver Upgrade  
Enter PIN code  
V.3.3  
1 Press the 6 buttons and choose  
Enter PIN code, then press a  
button  
Automatic Download  
Enabled  
Search for New Version  
2 Input the current PIN code  
When you are making this setting for the  
first time, input 0000.  
Switch automatic upgrade BACKExit submenu  
More..  
D0213-EN  
• The actual version may be different to  
the Receiver Upgrade version  
displayed above.  
When a PIN code has already been set,  
enter the correct PIN code.  
The PIN code setting window appears.  
2 Press the 6 buttons and choose  
Automatic Download, and press  
the 5 buttons to choose Enable  
or Disable  
CONFIGURATION  
Audio Language  
Subtitle  
English  
English  
Off  
Favourite Mode  
Receiver Upgrade  
Menu Lock  
V.3.5  
Installation  
Enter PIN code  
Enable (factory settings):  
PIN code:  
Confirm:  
The Digital terrestrial broadcasting  
(DVB-T) software is automatically  
updated every day at 3:00 am. When  
enabled, the TV also searches for new  
software whenever it goes to standby.  
0
..  
9
Enter PIN code  
BACKExit PIN code menu  
More..  
D0225-EN  
Disable:  
3 Press the number buttons to input  
a new PIN code (password)  
The Digital terrestrial broadcasting  
(DVB-T) software is not automatically  
updated.  
4 Input the new PIN code (password)  
again in the Confirm box  
Manually updating the Digital  
terrestrial broadcasting (DVB-T)  
information  
Your newly chosen PIN code is now set.  
You will now need to use the PIN code  
(password) you chose here to lock or  
unlock the Edit PR List’s “Lock”.  
Press the 6 buttons and choose  
Search for New Version, then press  
the a button  
The Digital terrestrial broadcasting (DVB-T)  
information is updated.  
27  
 
Operation with the DTV menu  
Choosing a channel  
The chosen channel is shown on the quarter-  
screen.  
Edit PR List  
The Edit PR List can be used to do the  
following:  
• delete registered channels  
• edit channel names  
1 Press the 5 buttons and choose  
Select on the bar at the bottom of  
the screen  
• lock channels so that they cannot be  
watched by children  
• set Favorites so that you can easily choose  
from only the channels you often watch.  
2 Press the 6 buttons and choose  
a channel, and then press the a  
button  
The picture of the chosen channel is  
shown on the quarter-screen.  
Choose Edit PR List and press the a  
button  
EDIT PR LIST appears.  
Deleting a channel  
• Sometimes you may notice a drop in  
picture quality while watching your  
programme in the quarter-screen. This is  
not a fault.  
1 Press the 5 buttons and choose  
Delete on the bar at the bottom of  
the screen  
2 Press the 6 buttons and choose  
the channel to be deleted, and then  
press the a button  
EDIT PR LIST  
1
BBC ONE  
1. BBC ONE  
2. BBC TWO  
7. BBC THREE  
30. CBBC Channel  
40. BBC NEWS 24  
51. BBCi  
The channel deletion confirmation  
window appears.  
EDIT PR LIST  
2
BBC TWO  
1. BBC ONE  
2. BBC TWO  
Select  
Delete  
Edit Name  
Lock  
Favourites  
More..  
7. BBC THREE  
30. CBBC Channel  
Select function  
Select PR OK Watch PR  
The selected service will be permanently  
D0202-EN  
deleted. Are you sure?  
Yes  
No  
• When the b button is pressed, the  
previous screen is returned to. When the  
TV/DTV or H buttons are pressed,  
the menu disappears.  
Select  
Delete  
Edit Name  
Lock  
Favourites  
More..  
Select function  
Select PR OK Delete PR  
D0215-EN  
• When the h (Information) button is  
pressed, the help screen appears. When it  
is pressed again, the previous screen is  
returned to.  
3 Choose Yes and press the a  
button  
The chosen channel is deleted.  
• If you do not want to delete the chosen  
channel, choose No and press the a  
button.  
• Perform “Installation” (see page 30) to  
re-register a channel that you have  
deleted.  
28  
 
Operation with the DTV menu  
Editing a channel name  
2 Press the 6 buttons and choose  
the channel to be locked, and then  
press the a button  
1 Press the 5 buttons and choose  
Edit Name on the bar at the bottom  
of the screen  
The Enter PIN code input window  
appears.  
2 Press the 6 buttons and choose  
the channel to be edited, and then  
press the a button  
EDIT PR LIST  
2
BBC TWO  
1. BBC ONE  
2. BBC TWO  
7. BBC THREE  
30. CBBC Channel  
4. BBC NEWS 24  
The edit window appears.  
Enter PIN code  
EDIT PR LIST  
2
BBC TWO  
1. BBC ONE  
2. BBC TWO  
7. BBC THREE  
30. CBBC Channel  
40. BBC NEWS 24  
51. BBCi  
Select  
Delete  
More..  
0
..  
9
Enter PIN code  
D0217-EN  
BBC TWO  
Select  
3 Press the number buttons to input  
the correct PIN code and press the  
a button  
Delete  
Edit Name  
Lock  
Favourites  
Select function  
D0216-EN  
Select PR OK Edit PR name  
More..  
If you have not changed the PIN code in  
the CONFIGURATION menu’s “Enter  
PIN code” (see page 27), input 0000.  
If you have changed the PIN code in the  
CONFIGURATION menu’s “Enter PIN  
code” (see page 27), input the PIN code  
you chose.  
3 Press the 6 buttons and choose  
a character, press the 5 buttons  
to move the cursor and edit the  
name, and then press the a  
button  
The edited channel appears in the Edit PR  
List.  
• Delete any unnecessary characters by  
entering spaces over them.  
The lock icon appears next to the channel  
name in the Edit PR List.  
EDIT PR LIST  
2
BBC TWO  
1. BBC ONE  
2. BBC TWO  
7. BBC THREE  
30. CBBC Channel  
40. BBC NEWS 24  
51. BBCi  
Locking a channel  
Digital terrestrial broadcasting (DVB-T)  
channels can be locked in the same way as  
the FEATURES menu CHILD LOCK.  
1 Press the 5 buttons and choose  
Lock on the bar at the bottom of the  
screen  
Select  
Delete  
Edit Name  
Lock  
Favourites  
More..  
0
..  
9
Enter PIN code  
D0218-EN  
When a locked channel is chosen, the  
Enter PIN code input window will appear.  
If the correct PIN code is input, the  
picture appears.  
• When you forget the PIN code for the  
“Lock”, you can unlock locked  
channels by performing Automatic  
Search (see “Installation” on page 30).  
29  
Operation with the DTV menu  
Setting the favourite channels  
Channels that you often watch can be set as  
favourite channels. You can choose from just  
those channels when the p p buttons are  
pressed.  
Installation  
Use when re-registering a channel or when  
registering a new channel.  
1 Choose Installation and press the  
a button  
• After setting the favourite channels, check  
that “Favourite Mode” in “Configuration”  
(see page 26) is set to ON.  
The Installation menu appears.  
Installation  
1 Press the 5 buttons and choose  
Favourites on the bar at the bottom  
of the screen  
Automatic Search  
Manual Search  
First Time Installation  
D0220-EN  
2 Press the 6 buttons and choose  
the channel to be registered as a  
favourite channel, and then press  
the a button  
2 Press the 6 buttons and choose  
the channel registration method,  
and then press the a button  
The favourite icon appears to the right of  
the chosen channel.  
Automatic Search:  
Choose to automatically register the  
channels that can be received.  
When Automatic Search is chosen and the  
a button is pressed, the confirmation  
window appears.  
LIST  
Start automatic search? Current PR list  
will be replaced.  
Yes  
No  
D0221-EN  
D0219-EN  
To perform Automatic Search, choose  
Yes and press the a button.  
To cancel, choose No and press the a  
button.  
Manual Search:  
Choose to register a particular channel.  
Installation > Manual Search  
Channel Number 61  
Signal Level:  
Signal Quality:  
Move cursor  
0
..  
9
OK Start  
More..  
Enter CH number  
D0222-EN  
Press the number buttons and input the  
channel that you want to register, and then  
press the a button. The Manual Search  
starts and the input channel is registered if  
it can be received.  
30  
   
Operation with the DTV menu  
First Time Installation:  
Choose when you have moved house etc  
and want to automatically re-register all  
the channels.  
In addition to registering all the channels  
that can be received, it will reset the timer  
settings.  
When Factory Settings is chosen and the  
a button is pressed, the confirmation  
window appears.  
Are you sure you want to delete the PR list  
and reset all settings?  
Yes  
No  
D0223-EN  
To perform Factory Settings, choose Yes  
and press the a button.  
To cancel, choose No and press the a  
button.  
Common Interface  
inserted into the CAM slot on the back of the  
TV, and you want to set the module for pay-  
per-view.  
When Common Interface is chosen and the  
a button is pressed, the name of the  
inserted module appears. When the a  
button is then pressed, the module setting  
menu appears.  
• When no module is inserted, “No CI  
Module” appears.  
• Refer to “To view the pay-per-view of the  
Digital Terrestrial broadcasting” on  
page 7 for deatils of the settings.  
31  
 
Operation while watching analogue TV  
PR LIST:  
The programme number (PR) and EXT  
terminal list is displayed.  
Pressing the a button after choosing the  
programme number (PR) or EXT terminal  
with the 7 buttons will display the  
Information function  
You can see the channel number of the  
programme you are watching, the current  
time or the PR LIST.  
From the PR LIST, you can choose a channel  
chosen programme or EXT terminal.  
or EXT terminal.  
• For programme numbers (PR) for which  
the CHILD LOCK function is set, the n  
(CHILD LOCK) mark is displayed. For  
details see “CHILD LOCK” on page 45.  
Press the  
display the information you want to  
see.  
(Information) button to  
h
Pressing the  
the display as follows:  
(Information) button changes  
h
PR LIST  
PR  
ID  
Channel number display  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
BBC1  
BBC2  
ITV  
CH4  
CH5  
12 : 00  
No indication  
OK  
-10  
+10  
D0011-EN  
Channel number display:  
The channel number and channel name  
(when the channel name is registered) of the  
programme you are watching or the EXT  
terminal number is displayed.  
Time display:  
The current time of the teletext data is  
displayed.  
If the TV has not received a TV channel that  
has teletext programmes since it was turned  
on, the time display is blank. To view the  
current time, choose a TV channel that has  
teletext programmes.  
• An incorrect current time is sometimes  
displayed when watching videos.  
32  
   
Analogue teletext function  
Basic operation  
1 Choose a TV channel with a teletext  
broadcast  
VCR/TV/  
DVD switch  
2 Set the VCR/TV/DVD switch to the  
TV position  
Number  
buttons  
Colour  
buttons  
3 Press g (Text) button to display  
the teletext  
Pressing g (Text) button changes the  
mode as follows:  
7
buttons  
TEXT  
TEXT  
---  
---  
TV mode  
TV and text mode  
TEXT  
TEXT  
---  
---  
D1043-EN  
Text mode  
4 Choose a teletext page by pressing  
the p p buttons, number buttons  
or colour buttons  
To return to the TV mode:  
Press the TV/DTV button or g (Text)  
button.  
• If you have trouble receiving teletext  
broadcasts, consult your local dealer or  
the teletext station.  
• The ZOOM function will not work in  
the TV and text mode or Text mode.  
• You cannot operate menus when  
viewing a teletext programme.  
33  
   
Analogue teletext function  
Using the List Mode  
Hold  
You can store the numbers of your favourite  
teletext pages in memory and call them up  
quickly using the colour buttons.  
You can hold a teletext page on the screen for  
as long as you want, even while several other  
teletext pages are being received.  
To store the page numbers:  
Press the C (Hold) button  
1 Press B button to go into the  
List mode  
Hold indication  
The page numbers you have stored are  
displayed at the bottom of the screen.  
To cancel the Hold function:  
Press C (Hold) button again.  
2 Press a colour button to choose a  
position. Then press the number  
buttons to enter the page number  
Sub-page  
Some teletext pages include sub-pages that  
are automatically displayed.  
1 Choose a teletext page that  
includes sub-pages  
Sub-page numbers that can be viewed are  
automatically displayed at the top of the  
screen.  
3 Press and hold down the A (Store)  
button  
The four page numbers blink white to  
show that they are stored in memory.  
2 Press the 5 buttons to choose a  
sub-page number  
To call up a stored page:  
Reveal  
1 Press the B button to enter the  
List mode  
Some teletext pages include hidden text  
(such as answers to a quiz).  
You can display the hidden text.  
2 Press a colour button having a  
stored page  
Each time you press the E (Reveal)  
button, text is hidden or revealed  
To exit the List mode:  
Press the B button again.  
34  
       
Analogue teletext function  
Size  
You can double the height of the teletext  
display.  
Press the F (Size) button  
Index  
You can return to the index page instantly.  
Press the G (Index) button  
Returns to page 100 or a previously specified  
page.  
Cancel  
You can search for a teletext page while  
watching TV.  
1 Press the number button to enter a  
page number, or press a colour  
button  
The TV searches for a teletext page.  
2 Press H (Cancel) button  
The TV programme appears. When the  
TV finds the teletext page, its page  
number appears in the upper left of the  
screen.  
3 Press H (Cancel) button to return  
to a teletext page when the page  
number is on the screen  
• The TV mode cannot be resumed by  
pressing the H (Cancel) button. To  
return to the TV mode press b.  
35  
     
Setting the TV  
Call the menu and perform the settings for  
the picture and sound.  
4 Press the 5 buttons to choose  
the setting of that function  
Buttons used to operate the menus  
• If you want to operate a function  
which appears only with its name,  
follow the descriptions of that function  
on the following pages.  
• The display appearing at the bottom of  
a menu shows you a button on the  
remote control that you can use when  
you operate a chosen function.  
TV/DTV  
5 Press the a button to complete  
the setting  
The menu disappears.  
Basic operation  
• When watching the television with the  
NTSC system, the menus are displayed  
at about half of their normal vertical  
size.  
1 Press the H button to display  
the MENU (main menu)  
MENU  
PICTURE SETTING  
PICTURE FEATURES  
SOUND SETTING  
EXT SETTING  
FEATURES  
INSTALL  
3D CINEMA SOUND  
DTV  
OK  
D5105-EN  
2 Press the 5 and 6 buttons to  
choose a menu title, and press the  
a button  
The menu appears.  
To return to the previous menu:  
Press the b button.  
To exit a menu instantly:  
Press the TV/DTV button.  
3 Press the 6 buttons to choose a  
function  
• For details of the functions in the  
menus, see the following pages.  
36  
   
PICTURE SETTING  
Refer to “Setting the TV” (see page 36) for  
details of displaying the menu.  
• You can change the HUE setting (picture  
hue) when the colour system is NTSC  
3.58, NTSC 4.43. (See “Specifications”  
on page 60)  
PICTURE SETTING  
PICTURE MODE  
CONTRAST  
BRIGHT  
BRIGHT  
To return to the default settings in  
each PICTURE MODE:  
Press the blue button.  
SHARP  
COLOUR  
HUE  
COLOUR TEMP.  
NORMAL  
RESET  
• This returns the picture settings in the  
PICTURE MODE mode you have chosen  
to the default settings, and stores them in  
the PICTURE MODE mode.  
OK  
D0014-EN  
PICTURE MODE  
COLOUR TEMP.  
You can choose one of three PICTURE  
MODEs to adjust the picture settings  
automatically.  
You can select one of three COLOUR  
TEMP. modes (three tones of white) to adjust  
the white balance of the picture. Since white  
is the colour which is used as a reference for  
all the other colours, changing the COLOUR  
TEMP. mode affects the appearance of all  
the other colours on the screen.  
BRIGHT:  
Heightens contrast and sharpness.  
STANDARD:  
Standardizes picture adjustment.  
SOFT:  
COOL:  
Softens contrast and sharpness.  
A bluish white. Using this mode when  
watching bright pictures allows you to enjoy  
a more vivid and bright picture.  
Picture Adjustment  
NORMAL:  
The normal white colour.  
You can change the picture settings of each  
PICTURE MODE mode as you like.  
WARM:  
CONTRAST:  
You can adjust the picture contrast.  
2 :lower  
A reddish white. Using this mode when  
watching films allows you to enjoy colours  
that are characteristic of films.  
3 : higher  
BRIGHT:  
You can adjust the picture brightness.  
2 :darker  
3 : brighter  
SHARP:  
You can adjust the picture sharpness.  
2 :softer  
3 : sharper  
COLOUR:  
You can adjust the picture colour.  
2 :lighter  
3 : deeper  
HUE:  
You can adjust the picture tint.  
2 :reddish  
3 : greenish  
37  
       
PICTURE FEATURES  
Refer to “Setting the TV” (see page 36) for  
details of displaying the menu.  
OFF:  
The DIGITAL VNR function is turned off.  
PICTURE FEATURES  
DigiPure Pro  
DIGITAL VNR  
AUTO  
AUTO  
DigiPure Pro  
COLOUR SYSTEM  
MOVIE THEATRE  
4:3 AUTO ASPECT  
PICTIRE TILT  
AUTO  
The DigiPure Pro function uses the latest in  
digital technology to give you a natural-  
looking picture.  
OK  
DigiPure function:  
D1015-EN  
This function helps to create a natural-  
looking picture by eliminating unnecessary  
edges from high-contrast and crisp images.  
For images with low-contrast, edges are  
added to produce a sharper, more detailed  
picture.  
• COLOUR SYSTEM cannot be chosen  
when watching Digital terrestrial  
broadcasting (DVB-T).  
DIGITAL VNR  
You can choose from the three DigiPure  
function settings of AUTO, MIN and MAX.  
The TV and external input may be given  
different DigiPure settings.  
• If you set the DigiPure effect too high on  
a low-quality picture that contains a lot of  
noise, this may actually make the noise  
worse. We recommend you use the  
AUTO setting if you can.  
The DIGITAL VNR function cuts down the  
amount of noise in the original picture.  
You can choose from the three DIGITAL  
VNR function settings of AUTO, MIN and  
MAX.  
The TV and external input may be given  
different DIGITAL VNR settings.  
AUTO:  
The TV will automatically adjust the level of  
the DIGITAL VNR effect to match the  
amount of noise in the picture, giving you the  
best possible picture.  
• If you set the DIGITAL VNR effect too  
high it can make the picture less sharp. It  
is recommended to use the AUTO setting  
if you can.  
Picture motion compensation  
function:  
This function displays fast-moving pictures  
more smoothly and naturally on the screen.  
• The effect level of the picture motion  
compensation function cannot be  
changed. The effect level is the same no  
matter which of the AUTO, MIN or MAX  
settings is used.  
MIN:  
The level of the DIGITAL VNR effect is set  
to the minimum. If you set the DIGITAL  
VNR function to AUTO but feel that the  
sharpness of the original picture has not been  
reproduced fully, change the setting from  
AUTO to MIN.  
1 Choose DigiPure Pro  
2 Press the 5 buttons to choose a  
setting. Then press the a button  
AUTO:  
The TV will automatically adjust the level of  
the DigiPure effect to match the amount of  
noise in the picture, giving the best possible  
picture.  
• The MIN setting is not suitable for low-  
quality pictures which contain a lot of  
noise.  
MAX:  
MIN:  
The level of the DIGITAL VNR effect is set  
to the maximum. If you set the DIGITAL  
VNR function to AUTO but still notice some  
noise, change the setting from AUTO to  
MAX.  
• The MAX setting is not suitable for high-  
quality pictures which contain very little  
noise.  
The level of DigiPure effect is set to the  
minimum. When you set the DigiPure Pro  
function to AUTO and notice some noise,  
change the setting from AUTO to MIN.  
• The MIN setting is not suitable for high-  
quality pictures which contain very little  
noise.  
38  
     
PICTURE FEATURES  
MAX:  
• The AUTO function may not function  
properly if you have poor signal quality.  
If the picture is abnormal in the AUTO  
function, choose another colour system  
manually.  
• When in the Programme numbers PR 0  
(AV) to PR 99, you cannot choose NTSC  
3.58 or NTSC 4.43.  
The level of DigiPure effect is set to the  
maximum. If you set the DigiPure Pro  
function to AUTO but feel that the original  
picture quality has not been reproduced fully,  
change the setting from AUTO to MAX.  
• The MAX setting is not suitable for low-  
quality pictures which contain a lot of  
noise.  
OFF:  
The DigiPure Pro function is turned off.  
MOVIE THEATRE  
The MOVIE THEATRE function displays a  
cinema film picture more smoothly and  
naturally on the screen.  
COLOUR SYSTEM  
The colour system is chosen automatically.  
However, if the picture is not clear or no  
colour appears, choose the colour system  
manually.  
AUTO:  
The television automatically recognizes the  
type of signal and turns the function on and  
off.  
COLOUR SYSTEM  
ON:  
This function is turned on.  
PAL  
OFF:  
This function is turned off.  
OK  
D1016-EN  
• The motion may appear unnatural when  
viewing images with the NTSC colour  
system. When the MOVIE THEATRE  
function is set to AUTO or ON, the  
motion may appear unnatural when  
viewing images with the NTSC colour  
system.  
1 Choose COLOUR SYSTEM then  
press the a button  
2 Press the 5 buttons to chose the  
appropriate colour system.  
Then press the a button  
PAL:  
PAL system  
NTSC 3.58:  
NTSC 3.58 MHz system  
NTSC 4.43:  
NTSC 4.43 MHz system  
AUTO:  
This function detects a colour system from  
the input signal. Only when you are viewing  
a picture from Programme number PR 0  
(AV), or EXT terminal, you can choose using  
the AUTO function.  
39  
   
PICTURE FEATURES  
4:3 AUTO ASPECT  
You can choose one of three ZOOM modes,  
REGULAR, PANORAMIC or 14:9 ZOOM,  
as the ZOOM mode for the normal picture  
(4:3 aspect ratio).  
1 Choose 4:3 AUTO ASPECT then  
press the a button  
4:3 AUTO ASPECT  
PANORAMIC  
REGULAR  
14:9 ZOOM  
OK  
D0017-EN  
2 Press the 6 buttons to choose a  
ZOOM mode. Then press the a  
button  
PICTURE TILT  
There are cases where the Earth’s magnetic  
force may make the picture tilt. If this  
happens, you can correct the picture tilt.  
1 Press the 6 buttons to choose  
PICTURE TILT. Then press the a  
button  
PICTURE TILT  
OK  
D0018-EN  
2 Press the 6 buttons until the  
picture becomes level. Then press  
the a button  
40  
   
SOUND SETTING  
Refer to “Setting the TV” (see page 36) for  
details of displaying the menu.  
Sound Adjustment  
You can adjust the sound to your liking.  
SOUND SETTING  
BASS:  
STEREO/  
BASS  
You can adjust the low tone of the sound.  
2 : weaker  
TREBLE  
BALANCE  
HYPER SOUND  
OFF  
ON  
3 : strong  
OK  
TREBLE:  
You can adjust the high tone of the sound.  
D0019-EN  
2 : weaker  
3 : strong  
STEREO / I • II  
BALANCE:  
You can adjust the volume balance between  
the left and right speaker.  
2 : turn the left speaker’s volume level up.  
3 : turn the right speaker’s volume level up.  
When you are viewing a bilingual broadcast  
programme, you can choose the sound from  
Bilingual I (Sub I) or Bilingual II (Sub II).  
When the stereo broadcasting is received  
poorly, you can change from stereo to mono  
sound so that you can hear the broadcast  
more clearly and easily.  
HYPER SOUND  
s: Stereo sound  
Mono sound is converted to simulated stereo  
for a more enjoyable audio experience.  
v : mono sound  
ON:  
t : Bilingual I (sub I)  
u : Bilingual II (sub II)  
This function is turned on.  
OFF:  
This function is turned off.  
• The sound mode you can choose differs  
depending on the TV programme.  
• This function does not work in the EXT  
and DTV modes. And this function does  
not appear in the SOUND SETTING  
menu.  
• If the audio is stereo sound, the “3D  
CINEMA SOUND function” (see  
page 18) is the better choice as it makes  
your listening experience more akin to  
sitting in an actual cinema.  
• When HYPER SOUND is turned on, 3D  
CINEMA SOUND turns off, and when  
3D CINEMA SOUND is turned on,  
HYPER SOUND turns off.  
41  
       
3D CINEMA SOUND  
Refer to “Setting the TV” (see page 36) for  
details of displaying the menu.  
3D CINEMA SOUND  
SURROUND  
BASS BOOST  
HIGH MID LOW  
HIGH MID LOW  
OK  
D0063-EN  
Adjust the 3D CINEMA SOUND effect.  
For details on how to turn 3D CINEMA  
SOUND on and off, read “3D CINEMA  
SOUND function” (see page 18).  
• In order to experience true 3D CINEMA  
SOUND, the audio needs to be stereo  
sound.  
• When the audio is mono sound, use  
“HYPER SOUND” (see page 41).  
SURROUND  
Adjust the surround effect.  
You can choose HIGH, MID or LOW.  
Choosing LOW will reduce the surround  
effect and choosing HIGH will increase the  
surround effect.  
BASS BOOST  
Adjust the bass sound.  
You can choose HIGH, MID or LOW.  
Choosing LOW will reduce the bass sound  
and choosing HIGH will increase the bass  
sound.  
42  
     
EXT SETTING  
Refer to “Setting the TV” (see page 36) for  
details of displaying the menu.  
To cancel the S-IN (S-VIDEO input)  
setting:  
Press the yellow button and turn off S-IN  
(S-VIDEO input) mark. The regular video  
signal (composite signal) pictures are  
resumed.  
EXT SETTING  
EXT-1  
EXT-3  
TV  
DUBBING  
EXT-2  
DTV  
• The EXT-1 terminal does not support  
S-VIDEO signal (Y/C signal) and you  
cannot set S-IN (S-VIDEO input) in  
the EXT-1 terminal.  
ID LIST  
OK  
S-IN  
D0020-EN  
• Setting S-IN (S-VIDEO input)  
changes the head character from “E” to  
“S”. For example, “E2” is changed to  
“S2”.  
S-IN (S-VIDEO input)  
When connecting a device (such as S-VHS  
VCR) which enables an S-VIDEO signal (Y/  
C signal) to be output, you can enjoy high-  
quality picture of the S-VIDEO signal (Y/C  
signal).  
• Even a device which enables the S-  
VIDEO signal (Y/C signal) to be  
output may output a regular video  
signal (composite signal) depending  
on the device setting. If a picture  
cannot appear because S-IN (S-  
VIDEO input) setting has been made,  
read the device Instruction Manual  
carefully again to check for the device  
settings.  
Preparation:  
• At first, read the Device Instruction  
Manual and “Additional preparation” on  
page 53 to connect the device to the TV  
properly. Second, follow the Device  
Instruction Manual to set the device so  
that an S-VIDEO signal (Y/C signal) can  
be output to the TV.  
ID LIST  
• Do not set S-IN (S-VIDEO input) to the  
EXT terminal connected to a device  
which cannot output an S-VIDEO (Y/C  
signal). If it is set wrongly, a picture  
cannot appear.  
You can have a name corresponding to the  
devices connected for each EXT terminal.  
Giving a name to an EXT terminal makes the  
EXT terminal number appear on the screen,  
together with the name.  
1 Choose an EXT terminal  
1 Choose an EXT terminal  
2 Press the yellow button and set the  
S-IN (S-VIDEO input).  
2 Press the blue button to display the  
name list (ID LIST)  
Then press the a button  
An S-IN (S-VIDEO input) mark is  
displayed. You can view an S-VIDEO  
signal (Y/C signal) instead of the regular  
video signal (composite signal).  
EXT SETTING  
EXT-1  
EXT-3  
TV  
DUBBING  
EXT-2  
ID LIST  
VHS  
S-VHS  
DVC  
CAM  
SAT  
STB  
DTV  
GAME  
DVD  
DVR  
OK  
D0021-EN  
43  
     
EXT SETTING  
TV:  
3 Press the 6 buttons to choose a  
name. Then press the a button  
The ID LIST disappears and the name is  
assigned to the EXT terminal.  
The picture and sound of the TV channel  
you are currently viewing are output from  
the EXT-2 terminal.  
DTV:  
• You cannot assign an EXT terminal  
name not found in the name list (ID  
LIST).  
The picture and sound of the Digital  
terrestrial braodcasting (DVB-T)TV  
channel you are currently viewing are  
output from the EXT-2 terminal.  
To erase a name assigned to the  
EXT terminal:  
Choose a blank space.  
• During dubbing, you cannot turn off  
the TV. Turning off the TV also turns  
off the output from the EXT-2  
terminal.  
4 Press the a button to complete  
the setting  
• When you choose an EXT terminal as  
an output, you can view a TV  
programme or a picture from the other  
EXT terminal while dubbing the  
picture from a device connected to the  
EXT terminal onto a VCR connected  
to the EXT-2 terminal.  
• The RGB signals from the TV games  
cannot be output. Teletext programmes  
cannot be output.  
DUBBING  
You can choose a signal source to be output  
from an EXT-2 terminal.  
You can choose any one of the output signal  
of the device connected to the EXT terminal  
and the picture and sound from a TV channel  
you are currently viewing to output it to the  
EXT-2 terminal.  
1 Press the 5 buttons to choose  
the arrow from the menu  
EXT SETTING  
EXT-1  
EXT-3  
TV  
DUBBING  
EXT-2  
DTV  
OK  
D0022-EN  
2 Press the 6 buttons to choose an  
EXT terminal or TV.  
Then press the a button  
The arrow in the menu represents a signal  
flow. The left side of the arrow denotes a  
signal source output from the EXT-2  
terminal.  
EXT-1/EXT-3:  
The output signal of the device connected  
to an EXT terminal passes through the TV  
and is output from the EXT-2 terminal.  
44  
 
FEATURES  
Refer to “Setting the TV” (see page 36) for  
details of displaying the menu.  
To cancel the SLEEP TIMER  
function:  
Press the 2 button to set a period of time  
to “OFF”.  
FEATURES  
SLEEP TIMER  
BLUE BACK  
OFF  
OFF  
ON  
ON  
CHILD LOCK  
DECODER(EXT-2)  
BLUE BACK  
OK  
You can set the TV to automatically change  
to a blue screen and mute the sound if the  
signal is weak or absent, or when there is no  
input from an external device.  
D0023-EN  
• BLUE BACK, CHILD LOCK, and  
DECODER (EXT-2) cannot be chosen  
when watching Digital terrestrial  
broadcasting (DVB-T).  
ON:  
This function is turned on.  
OFF:  
SLEEP TIMER  
This function is turned off.  
You can set the TV to automatically turn off  
after a specified period of time.  
CHILD LOCK  
When there is a TV channel you wish your  
children not to watch, you can use the  
CHILD LOCK function to lock out the TV  
channel. Even when a child chooses a  
Programme number (PR) in which a locked  
TV channel has been registered, the screen  
will change to light blue and displays n  
(CHILD LOCK) so the TV channel cannot  
be viewed. Unless you enter a pre-set ID  
number by a special operation, the lock  
cannot be released and the child cannot view  
the TV channel programmes.  
1 Choose SLEEP TIMER, then press  
the a button  
A Sub-menu of the SLEEP TIMER  
function appears.  
SLEEP TIMER  
0
120  
OFF  
OK  
D0024-EN  
2 Press the 5 buttons to set the  
period of time.  
To set the CHILD LOCK function  
Then press the a button  
You can set the period of time a  
maximum of 120 minutes (2 hours) in 10  
minute increments.  
• One minute before the SLEEP TIMER  
function turns off the TV, “GOOD  
NIGHT!” appears.  
1 Choose CHILD LOCK, then press  
the 0 button  
“SET ID NO.” (ID number setting screen)  
appears.  
SET ID NO.  
0000  
• The SLEEP TIMER function cannot  
be used to turn off the TV’s main  
power.  
OK  
D0025-EN  
• When the SLEEP TIMER function is  
on, you can display the Sub-menu of  
the SLEEP TIMER function again to  
confirm and/or change the remaining  
period of time of the SLEEP TIMER  
function. Press the a button to exit  
the menu after confirming and / or  
changing the remaining time.  
2 Set the ID number to your liking  
1 Press the 6 buttons to choose  
a number.  
2 Press the 5 buttons to move  
the cursor.  
45  
       
FEATURES  
3 Press the a button  
2 Press the  
(Information) button  
h
The Sub-menu of CHILD LOCK appears.  
while the n (CHILD LOCK) is  
displayed  
CHILD LOCK  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
The “ID NO.” (ID NO. input screen)  
appears.  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
21  
22  
23  
24  
25  
26  
27  
28  
29  
LOCK  
OK  
3 Press the Number buttons to enter  
the ID number  
D0026-EN  
The lock is temporarily released so you  
can view the TV channel.  
4 Press the 6 buttons to choose a  
TV channel  
If you have forgotten the ID  
number:  
Perform step 1 of “To set the CHILD  
LOCK function”. After confirming the ID  
number, press the TV/DTV button to exit  
the menu.  
Every time you press the 6 buttons, the  
Programme number (PR) changes, and the  
picture of the TV channel registered in the  
Programme number (PR) is displayed on  
the screen.  
5 Press the blue button and set the  
CHILD LOCK function.  
• Even if you reset the lock temporarily,  
it does not mean that the CHILD  
LOCK function set for the TV channel  
is cancelled. The next time anyone  
attempts to view the TV channel, it  
will be locked again.  
• When you would like to cancel the  
CHILD LOCK function, you must  
perform the operation “To set the  
CHILD LOCK function” again.  
• To disable easy choosing of a  
Programme number (PR) in which a  
locked TV channel has been  
Then press the a button  
n (CHILD LOCK) appears and the TV  
channel is locked.  
To reset the CHILD LOCK function:  
Press the blue button again.  
n (CHILD LOCK) disappears.  
To disable easy resetting of the CHILD  
LOCK function, the menu disappears by  
choosing the CHILD LOCK function and  
pressing the a button as in the ordinary  
menu operation.  
registered, the Programme number  
(PR) has been set that it cannot be  
chosen by the 6 buttons or the  
operation buttons at the TV.  
To view a locked TV channel  
1 Choose a Programme number (PR)  
in which a TV channel locked with  
the Number buttons or PR LIST  
The screen changes to light blue and the n  
(CHILD LOCK) appears. You cannot  
view the TV channel.  
• To disable easy resetting of the lock,  
“ID NO.” (ID NO. input screen) is set  
so that it cannot appear unless you  
press the  
(Information) button.  
h
46  
FEATURES  
DECODER (EXT-2)  
Only when connecting a Decoder with a T-V  
LINK compatible VCR connected to the  
EXT-2 terminal, you can use this function.  
Caution  
• If you have not connected a Decoder with  
a T-V LINK compatible VCR connected to  
the EXT-2 terminal, setting this function to  
“ON” by mistake causes the picture/  
sound of a TV channel you are currently  
viewing not to be issued.  
47  
 
INSTALL  
Refer to “Setting the TV” (see page 36) for  
details of displaying the menu.  
2 Press the a button to display the  
T-V LINK menu  
INSTALL  
T-V LINK  
AUTO PROGRAM  
EDIT / MANUAL  
ATTENUATOR  
DOWNLOAD TV  
RECORDING DEVICE  
OFF ON  
OK  
OK  
D0029-EN  
EXIT  
• AUTO PROGRAM and EDIT/MANUAL  
cannot be chosen when watching Digital  
terrestrial broadcasting (DVB-T).  
D0005-EN  
3 If you do not have a T-V LINK  
compatible VCR connected:  
Press the TV/DTV button to exit the T-V  
LINK menu.  
AUTO PROGRAM  
You can automatically register the TV  
channels which can be received well at your  
residence in the TV’s Programme numbers  
(PR) by performing the following.  
If you have a T-V LINK compatible  
VCR connected to the EXT-2  
terminal:  
Follow the operating procedure  
“Downloading the data to VCR” on  
page 10 to transmit the Programme  
number (PR) data.  
1 Choose AUTO PROGRAM. Then  
press the a button  
The AUTO PROGRAM menu appears  
and received TV channels are  
automatically registered in the  
Programme numbers (PR).  
• To cancel the AUTO PROGRAM  
function, press the b button.  
• When your TV can detect the TV  
channel name from the TV channel  
broadcast signal, it automatically  
registers the TV channel name (ID) to  
the TV channel has been registered.  
• If a TV channel you want to view is  
manually set it using the MANUAL  
function. For details, see “EDIT/  
MANUAL” on page 49.  
AUTO PROGRAM  
EDIT  
PR  
ID  
CH  
CH 10  
20%  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
BBC1  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
21  
22  
23  
24  
25  
26  
27  
28  
29  
OK  
ID  
MANUAL  
OK  
MOVE  
INSERT DELETE  
D0004-EN  
• The TV channel is not registered in  
Programme number PR 0 (AV). When  
you want to register a TV channel to  
PR 0 (AV) manually set it using the  
MANUAL function. For details, see  
“EDIT/MANUAL” on page 49.  
After the TV channels have been  
registered in the Programme  
numbers (PR), the EDIT menu  
appears.  
• You can proceed to edit the  
Programme numbers (PR) using the  
EDIT/MANUAL function. For details,  
see “EDIT/MANUAL” on page 49.  
• If you do not need to use the EDIT/  
MANUAL function, go to the next  
step.  
48  
   
INSTALL  
• The CH number is a number unique to  
the TV and corresponding to the  
Channel number between a TV  
channel. For the relationship of a  
Channel number and a CH number, see  
“CH numbers” on page 56.  
EDIT/MANUAL  
The EDIT/MANUAL functions are divided  
into two types: editing of the current  
Programme numbers (PR) (EDIT functions)  
and manual registration of a TV channel you  
want to view to the Programme number (PR)  
(MANUAL function). The details about  
these functions are as follows:  
2 Follow the operation description of  
a function you want to use and  
operate the function  
Caution  
MOVE:  
• Using the MOVE, DELETE or INSERT  
function rewrites the current Programme  
numbers (PR) list. Resultingly, the  
Programme number (PR) of some of the  
TV channels will change.  
• Using the MANUAL function for a TV  
channel for which the CHILD LOCK  
function has been set cancels the CHILD  
LOCK function for the TV channel.  
• Using the MANUAL function for a TV  
channel for which the DECODER (EXT-2)  
function has been set to ON returns the  
setting of the DECODER (EXT-2) function  
for the TV channel to OFF.  
This function changes a Programme  
number (PR) of a TV channel.  
ID:  
This function registers a Channel name  
(ID) to a TV channel.  
INSERT:  
This function adds a new TV channel in  
the current Programme numbers (PR) list  
by using the CH number.  
• You cannot use the INSERT function  
if you do not know a Channel number  
of a TV channel. Use the MANUAL  
function to register a TV channel in the  
Programme number (PR).  
• When a TV channel has already been  
registered in PR 99, using the INSERT  
function deletes the TV channel.  
DELETE:  
This function deletes an unnecessary TV  
channel.  
1 Choose EDIT/MANUAL, then press  
the a button  
MANUAL:  
EDIT  
This function manually registers a new  
TV channel in a Programme number  
(PR).  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
21  
22  
23  
24  
25  
26  
27  
28  
29  
3 Press the a button to complete  
the settings  
ID  
MANUAL  
The T-V LINK menu appears.  
OK  
MOVE  
INSERT DELETE  
T-V LINK  
D0038-EN  
DOWNLOAD TV  
RECORDING DEVICE  
• For Programme number PR 0, “AV”  
appears in the Programme numbers  
(PR) list.  
OK  
EXIT  
• An EXT terminal number does not  
appear in the Programme numbers  
(PR) list.  
D0005-EN  
49  
 
INSTALL  
4 If you do not have a T-V LINK  
ID  
1 Press the 6 buttons to choose a  
compatible VCR connected:  
Press the TV/DTV button to exit the T-V  
LINK menu.  
The T-V LINK menu disappears and all  
the settings are completed.  
TV channel  
Every time you press the 6 buttons, the  
Programme number (PR) is changed over,  
and the picture of the TV channel  
registered in the Programme number (PR)  
appears on the screen.  
If you have a T-V LINK compatible  
VCR connected to the EXT-2  
terminal:  
Follow the operating procedure  
“Downloading the data to VCR” on  
page 10 to transmit the Programme  
number (PR) data to the VCR.  
2 Press the red button to start the ID  
function  
EDIT  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
21  
22  
23  
24  
25  
26  
27  
28  
29  
MOVE  
1 Press the 6 buttons to choose a  
TV channel  
ID LIST  
Every time you press the 6 buttons, the  
Programme number (PR) is changed over,  
and the picture of the TV channel  
registered in the Programme number (PR)  
appears on the screen.  
OK  
D0031-EN  
3 Press the 6 buttons to choose  
the first character of a Channel  
name (ID) you want to attach to the  
TV channel  
2 Press the 3 button to start the  
MOVE function  
EDIT  
EDIT  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
21  
22  
23  
24  
25  
26  
27  
28  
29  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH  
CH  
CH  
CH  
CH  
CH  
21  
22  
23  
24  
25  
26  
M
CH  
27  
CH  
CH  
28  
29  
ID LIST  
OK  
OK  
STORE  
D0032-EN  
D0030-EN  
4 Press the blue button to display the  
ID LIST (channel name list)  
3 Press the 6 buttons to choose a  
new Programme number (PR)  
ID LIST  
EDIT  
To cancel the MOVE function:  
Press the b button.  
M6  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
MBC  
MCM  
MDR  
MOVIE  
MTV  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
21  
22  
23  
24  
25  
26  
27  
28  
29  
MTV3  
4 Press the 2 button to change the  
Programme number (PR) of a TV  
channel to a new Programme  
number (PR)  
M
OK  
D0033-EN  
50  
INSTALL  
• The CH number is a number indicating  
the broadcast frequency to the TV. If  
the TV cannot detect the TV channel  
corresponding to the broadcast  
frequency indicated by the CH  
number, a picture in the no-signal state  
appears.  
5 Press the 6 buttons to choose  
the Channel name (ID)  
To cancel the ID function:  
Press the b button.  
6 Press the a button to register a  
Channel name (ID) to a TV channel  
DELETE  
• You can register your unique Channel  
name (ID) to the TV channel. When  
step 3 is completed, do not go to step  
4, but press the 5 buttons to move  
the cursor and the 6 buttons to  
choose a character for completing the  
Channel name (ID). Then press the  
a button to register the Channel  
name (ID) to the TV channel.  
1 Press the 6 buttons to choose a  
TV channel  
Every time you press the 6 buttons, the  
Programme number (PR) is changed over,  
and the picture of the TV channel  
registered in the Programme number (PR)  
appears on the screen.  
2 Press the yellow button to delete  
the TV channel  
INSERT  
The TV channel is deleted from the  
Programme numbers (PR) list.  
1 Press the 6 buttons to choose a  
Programme number (PR) for which  
you will register a new TV channel  
MANUAL  
1 Press the 6 buttons to choose a  
Programme number (PR) to which  
you want to register a new TV  
channel  
2 Press the green button and start  
the INSERT function.  
EDIT  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
2 Press the blue button to activate  
the MANUAL function  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
21  
22  
23  
24  
25  
26  
MANUAL  
28  
29  
PR  
AV  
01  
02  
03  
04  
05  
06  
07  
08  
09  
ID  
CH  
BBC1  
BBC2  
ITV  
CH4  
CH5  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
CH  
21  
22  
23  
24  
25  
26  
27  
28  
29  
OK  
0
9
D0034-EN  
To cancel the INSERT function:  
Press the b button.  
SEARCH+  
FINE-  
OK  
FINE+  
SEARCH-  
3 Press the Number buttons to enter  
the remaining CH number  
The TV shifts to registration mode.  
When the registration is completed, the  
picture of the TV channel appears on the  
screen.  
D0035-EN  
To cancel the MANUAL function:  
Press the b button.  
51  
 
INSTALL  
3 Press the green or red button to  
search for a TV channel  
Scanning stops when the TV finds a TV  
channel. Then the TV channel is  
displayed.  
4 Press the green or red button  
repeatedly until the TV channel you  
want appears  
If the TV channel reception is poor:  
Press the blue or yellow button to fine-  
tune the TV channel.  
5 Press the a button and register  
the TV channel to a Programme  
number (PR)  
The normal EDIT menu is resumed.  
ATTENUATOR  
Turn the attenuator ON when noise is  
introduced into the picture or sound due to  
strong electric fields.  
Normally use the TV with the attenuator  
turned OFF.  
52  
 
Additional preparation  
Connecting the external devices  
Connect the devices to the TV, paying  
attention to the following connection  
diagram.  
2 VCR (composite signal/S-VIDEO signal)  
3 T-V LINK compatible VCR (composite  
signal/S-VIDEO signal)  
4 Decoder  
5 DVD player (composite signal/S-VIDEO  
signal)  
6 DVD player (composite signal/RGB  
signal)  
7 TV game (composite signal/RGB signal)  
8 TV game (composite signal/S-VIDEO  
signal)  
9 Headphones  
0 Camcorder (composite signal/S-VIDEO  
signal)  
Before connecting anything:  
• Read the manuals provided with the  
devices. Depending on the devices, the  
connection method may differ from the  
figure. In addition, the device settings  
may be changed depending on the  
connection method to secure proper  
operation.  
• Turn off all the devices including the TV.  
• The “Specifications” on page 60 contains  
the details of the EXT terminals. If you  
are connecting a device not listed in the  
following connection diagram, see the  
table to choose the best EXT terminal.  
• Note that connecting cables are not  
supplied.  
- SCART cable  
= Audio cable  
~ Video cable  
! S-VIDEO cable  
• If the VCR’s audio output is in mono,  
connect the VCR’s AUDIO OUT (audio  
output) terminal and the TV’s EXT-3  
AUDIO L/MONO terminal with an audio  
cable.  
Side of the TV  
S
R
L/MONO  
EXT-3  
P
S
R
L/MONO  
EXT-4  
P
Back of the TV  
SERVICE  
EXT-1  
EXT-2  
R
AUDIO OUT  
53  
   
Additional preparation  
Equipment which can output the  
S-VIDEO signal (Y/C signal)  
Connect the equipment to an EXT terminal  
(but not the EXT-1 terminal).  
TV output from the EXT-1 terminal  
The video/sound signal of a Analogue  
terrestrial broadcasting channel you are  
viewing is always output from the EXT-1  
terminal.  
You can choose between an S-VIDEO signal  
(Y/C signal) and a regular video signal  
(composite signal). For details of how to  
operate the equipment, see “S-IN (S-VIDEO  
input)” on page 43.  
• Changing over a programme number (PR)  
also changes over the TV output from the  
EXT-1 terminal.  
• The video/sound signal from an EXT  
terminal cannot be output.  
T-V LINK compatible VCR  
Be sure to connect the T-V LINK compatible  
VCR to the EXT-2 terminal. If not, the T-V  
LINK function will not work properly.  
VCR to the EXT-2 terminal, be sure to  
connect the decoder to the VCR. If not,  
the T-V LINK function may not work  
properly.  
• Teletext programmes cannot be output.  
Connection when recording to  
• When recording an Analogue terrestrial  
EXT-1 or EXT-2. If you connect to the  
EXT-2 terminal, make sure the  
“DUBBING” setting (see page 44) is set  
to “TV”.  
• Choose the EXT-2 terminal to connect to  
a T-V LINK compatible VCR.  
When recording an Analogue terrestrial  
broadcasting, set the “DUBBING” setting  
(see page 44) to “TV”.  
• When you connect the decoder to the  
VCR, after you have stored TV channels  
in the programme numbers (PR) list, set  
the DECODER (EXT-2) function for the  
programme number (PR) to ON to  
unscramble a scrambled TV channel. For  
details, see “DECODER (EXT-2)” on  
page 47.  
When recording a Digital terrestrial  
broadcasting (DVB-T), set the  
“DUBBING” setting (see page 44) to  
“DTV”.  
Connecting headphones  
Connect the headphones with a stereo mini-  
jack (3.5 mm diameter) to the headphone  
jack socket.  
when the headphones are connected and  
only one screen is displayed.  
Video or sound signal output from  
the EXT-2 terminal  
You can change over the output of the video/  
sound signal from the EXT-2 terminal. This  
is useful when you want to dub the video/  
sound from another device onto the VCR  
connected to the EXT-2 terminal. For details  
on how to do this, see “DUBBING” on  
page 44.  
54  
 
Additional preparation  
Connecting Speakers/Amplifier  
While referring to the Audio equipment  
connection diagram, connect the audio  
equipment you desire to the TV.  
Operating a JVC brand VCR or  
DVD player  
These buttons will operate a JVC brand VCR  
or DVD player. Pressing a button that looks  
the same as the device’s original remote  
control button has the same effect as the  
original remote control.  
You can use external front speakers to listen  
to the TV sound instead of the TV speakers.  
Before connecting anything:  
• Read the manuals provided with the  
amplifier and speakers.  
• Turn the TV and Amplifier off.  
• To prevent magnetism from the speakers  
adversely effecting the TV screen, use  
magnetic-shielded speakers for the front  
speakers.  
1 Set the VCR/TV/DVD Switch to the  
VCR or DVD position  
VCR:  
When you are operating the VCR, set the  
switch to the VCR position.  
• You can turn the VCR on or off with  
the # (standby) button.  
• Note that connecting cables are not  
supplied.  
Back of the TV  
DVD:  
L
R
When you are operating the DVD player,  
set the switch to the DVD position.  
• You can turn the DVD player on or off  
with the # (standby) button.  
• You can also press the H or  
T button and display the  
DVD disc menu screen, and then  
operate by pressing the 7  
buttons.  
1
2
Amplifier  
Front speakers (Magnetic-shielded type)  
• The output from the AUDIO OUT  
terminal is not interrupted by headphone  
connection to the TV. You cannot cut the  
sound from the front speaker even if you  
connect a headphone to the TV.  
• Adjust the volume of the external  
speakers with the amplifier.  
2 Press the VCR/DVD Control Button  
to control your VCR or DVD player  
• If your device is not made by JVC,  
these buttons will not work.  
• Even if your device is made by JVC,  
some of these buttons may not work,  
depending on the device you are using.  
• You can use the p buttons to choose  
a TV channel the VCR will receive, or  
choose the chapter the DVD player  
plays back.  
• Some models of DVD player use the  
p buttons for both operating the fast  
forward/backward functions and for  
choosing the chapter. In this case, the  
253 buttons do not work.  
You cannot turn the TV on or off when the  
VCR/TV/DVD switch is set to the VCR or  
DVD position.  
When you turn the TV on or off, set the  
VCR/TV/DVD switch to the TV position.  
55  
   
CH numbers  
When you want to use the INSERT function on page 51, find the CH number corresponding to the  
Channel number of the TV channel from this table.  
CH  
Channel  
E21  
E22  
E23  
E24  
E25  
E26  
E27  
E28  
E29  
E30  
E31  
E32  
E33  
E34  
E35  
E36  
E37  
E38  
E39  
E40  
E41  
E42  
E43  
E44  
E45  
CH  
Channel  
E46  
E47  
E48  
E49  
E50  
E51  
E52  
E53  
E54  
E55  
E56  
E57  
E58  
E59  
E60  
E61  
E62  
E63  
E64  
E65  
E66  
E67  
E68  
E69  
CH 21  
CH 22  
CH 23  
CH 24  
CH 25  
CH 26  
CH 27  
CH 28  
CH 29  
CH 30  
CH 31  
CH 32  
CH 33  
CH 34  
CH 35  
CH 36  
CH 37  
CH 38  
CH 39  
CH 40  
CH 41  
CH 42  
CH 43  
CH 44  
CH 45  
CH 46  
CH 47  
CH 48  
CH 49  
CH 50  
CH 51  
CH 52  
CH 53  
CH 54  
CH 55  
CH 56  
CH 57  
CH 58  
CH 59  
CH 60  
CH 61  
CH 62  
CH 63  
CH 64  
CH 65  
CH 66  
CH 67  
CH 68  
CH 69  
56  
 
Troubleshooting  
Digital terrestrial broadcasting (DVB-T) service area  
Although this TV can receive both Digital terrestrial broadcasting (DVB-T) and Analogue terrestrial  
broadcasting, depending on the area in which you live, you may not be able to receive Digital  
terrestrial broadcasting (DVB-T).  
For details of the Digital terrestrial broadcasting (DVB-T) service area, refer to the FREEVIEW  
website etc.  
If a problem arises while you are using the TV, please read this troubleshooting guide carefully  
before you ask to have the TV repaired. You may be able to fix it easily by yourself. For example,  
if the mains plug is disconnected from the mains outlet, or the TV aerial has problems, you may  
think there is a problem with the TV itself.  
Important:  
• This troubleshooting guide only covers problems whose causes are not easy to decide. If you  
have a question when you are operating a function, read the page(s) for that function carefully,  
not this troubleshooting guide.  
• If you follow the advice in this troubleshooting guide without any success, unplug the mains  
plug and ask for your TV to be repaired. Do not attempt to repair the TV by yourself or to  
remove the rear cover of the TV.  
If you cannot turn on the TV  
Poor picture  
• Is the AC plug connected to the AC  
outlet?  
• Is the Power lamp lit? If not, press the  
Main power button.  
• Make sure you set the VCR/TV/DVD  
switch to the TV position. You cannot  
turn the TV on when the VCR/TV/DVD  
switch is set to the VCR or DVD position.  
• If the Digital terrestrial broadcasting  
(DVB-T) picture is unnatural, press the  
Main power button on the TV and turn off  
the main power. Try to press the Main  
power button again to turn on the main  
power. The picture may appear natural  
again.  
• If noise (snow) totally blocks out the  
picture, there may be a problem with the  
aerial or aerial cable. Check the following  
to try to solve the problem:  
– Have the TV and aerial been connected  
properly?  
– Has the aerial cable been damaged?  
– Is the aerial pointing in the right  
direction?  
If you cannot turn off the TV  
• Make sure you set the VCR/TV/DVD  
switch to the TV position. You cannot  
turn the TV off when the VCR/TV/DVD  
switch is set to the VCR or DVD position.  
No picture or no sound  
• Have you chosen a TV channel with very  
poor reception? If so, the BLUE BACK  
function will be activated: the entire  
screen becomes blue, and the sound is  
muted. If you still want to view the TV  
channel, follow the description “BLUE  
BACK” on page 45 to change the BLUE  
BACK function setting to OFF.  
– Is the aerial itself faulty?  
• If the TV or aerial suffers interference  
from other equipment, stripes or noise  
may appear in the picture. Move any  
equipment such as an amplifier, personal  
computer, or a hair drier, that can cause  
interference away from your TV. Or try  
moving the TV. If the aerial suffers  
interference from a radio tower or high-  
voltage wire, please contact your local  
dealer.  
57  
 
Troubleshooting  
• If the TV suffers interference from signals  
reflecting from mountains or buildings,  
double-pictures (ghosting) will occur. Try  
to change the aerial’s direction or replace  
it with one with better directionality.  
• Are your COLOUR SYSTEM settings  
correct? Follow the description  
• When you are viewing a teletext  
programme, you cannot operate the  
menus. Press the TV/DTV button to  
return to the ordinary TV programme, and  
then try operating the menus.  
• If the TV suddenly stops responding,  
disconnect the power cord of the TV from  
the AC outlet. Connect them to the AC  
outlet again to turn on the TV. If the TV  
returns to a normal state, it is not a failure.  
“COLOUR SYSTEM” on page 39 to try  
to solve the trouble.  
• Have the COLOUR and BRIGHT settings  
been adjusted properly? Follow the  
description “Picture Adjustment” on  
page 37 to try to adjust them properly.  
• Videotaping teletext is not recommended  
because it may not record correctly.  
• When viewing images from commercially  
available video software products, or  
videos from videotapes which have been  
recorded improperly, the top of the image  
may be distorted. This is due to the  
condition of the video signal. There is  
nothing wrong with the TV.  
• When a white and bright still image (such  
as a white dress) is displayed on the  
screen, the white part may look as if it  
were coloured. It is a phenomenon  
unavoidable due to the nature of the  
picture tube itself, and not due to a TV  
failure. When the picture disappears from  
disappear.  
Other issues  
• When the SLEEP TIMER function  
operates, the TV is automatically turned  
off. If the TV suddenly turns off, try to  
press the # (standby) button to turn on  
the TV once again. If the TV goes back to  
normal, there is no problem.  
• When the TV is receiving a wide-screen  
signal (WSS) or a signal from an external  
device affecting the screen size, the  
ZOOM mode automatically changes.  
ZOOM mode, press the c button  
again.  
• It takes a short period of time from the  
time an operation such as changing  
channels is performed until an image is  
displayed. This is not a fault. This is the  
time needed for the image to stabilise  
before it can be displayed.  
Poor sound  
• The TV may make a crackling sound due  
to a sudden change in temperature. The  
picture or sound may be normal. If you  
hear crackling sounds frequently while  
you are viewing the TV, there may be  
other causes. As a precaution, ask your  
service technician to inspect it.  
• Have you adjusted BASS or TREBLE  
properly? If not, follow the description  
“Sound Adjustment” on page 41.  
If the TV does not respond to the  
remote control  
• Have the batteries of the remote control  
worn out? Follow the description “Putting  
the batteries into the remote control” on  
page 7 and replace them with new batteries.  
• Have you attempted to use the remote  
control from the sides or rear of the TV or  
from more than seven metres away from the  
TV? Use the remote control in front of your  
TV or from less than seven metres away.  
• If you bring a magnetised device such as a  
speaker near to your TV, a picture may be  
warped or unnatural colours appear at the  
corners of the screen. In this case, keep  
the device apart from your TV. If the  
speakers causes such phenomena, use the  
magnetic-shielded speakers instead.  
58  
Troubleshooting  
• A picture may be tilted due to the  
influence of the earth’s magnetism. In this  
case, use the “PICTURE TILT” on  
page 40 to complete the tilt.  
• Touching the screen may cause you feel a  
slight electric shock due to its static  
electricity. It is an unavoidable  
phenomenon due to the construction of  
the picture tube. It is not a problem with  
the TV. You can rest assured that this  
static discharge does not have harmful  
influence over the human body.  
• If an error message appears on the screen  
when viewing Digital terrestrial  
broadcasting channel and does not  
disappear, because channel from the PR  
list may have been deleted. Try  
registering all the channels again using  
“Automatic Search:” on page 30 to solve  
the trouble.  
59  
Specifications  
Model  
Item  
AV-32EX5BK  
AV-28EX5BK  
Broadcasting systems  
Colour systems  
CCIR, I  
PAL  
• The EXT terminals also support the NTSC 3.58/4.43 MHz system.  
Analogue: E21-E69, Digital: 474 MHz - 850 MHz (channel 21 - 68)  
NICAM (I) system, Digital (DVB-T): MHEG 5 UK profile  
FLOF (Fastext), WST (World Standard System)  
220 - 240 V AC, 50 Hz  
Channels and frequencies  
Sound-multiplex systems  
Teletext systems  
Power requirements  
Power consumption  
Picture tube size  
138 W, Standby: 2.8 W  
134 W, Standby: 2.8 W  
Viewable area 76 cm (measured  
diagonally)  
Viewable area 66 cm (measured  
diagonally)  
Audio output  
Speakers  
Rated Power output: 10 W + 10 W  
(13 cm × 6.5 cm) oval × 2  
EXT-1 terminal  
Euroconnector (21-pin, SCART)  
• Video input, Audio L/R inputs and RGB inputs are available.  
• TV broadcast outputs (Video and Audio L/R) are available.  
EXT-2 terminal  
Euroconnector (21-pin, SCART)  
• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.  
• Video and Audio L/R outputs are available.  
• T-V LINK functions are available.  
EXT-3 terminal  
RCA connectors × 3  
S-VIDEO connector × 1  
• Video input, S-VIDEO (Y/C) input, Audio L/MONO and R inputs are available.  
AUDIO OUT terminal  
RCA connectors × 2  
• Audio L/R outputs are available.  
Headphone jack  
Dimensions (W × H × D)  
Weight  
Stereo mini-jack (3.5 mm in diameter)  
864 mm × 587 mm × 550 mm  
762 mm × 528 mm × 493 mm  
54.0 kg  
40.0 kg  
Accessories  
Remote control unit × 1 (RM-C1814S)  
AA/R6 dry cell battery × 2  
• This TV has the CAM (Conditional Access Module) slot for watching pay-per-view.  
Please note that the CAM and Viewing Card must be purchased separately.  
We may change the design and specifications without notice.  
Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any  
commercial or demonstration purpose in public places (cafes, hotels, etc.) without the consent of  
the owners of copyright of the original picture sources, as this would be an infringement of  
copyright.  
60  
 
LCT1821-001A-U  
0405TKH-CR-MU  
© 2005 Victor Company of Japan, Limited  

Intel DESKTOP BOARD D925XCV User Manual
Intel EMX 965GME User Manual
JVC AV 21FT5BU User Manual
Lenovo LXH GJ769F4 User Manual
Magnavox 1VMN29897 User Manual
M Systems Flash Disk Pioneers DVR 115DSV User Manual
Optiquest VS11351 User Manual
Panasonic BT LH80W User Manual
Philips 21PT2382 User Manual
Philips HDR3700 User Manual